arch/arm64/boot/dts/qcom/sdm845-cheza.dtsi

   1 // SPDX-License-Identifier: (GPL-2.0+ OR MIT)
   2 /*
   3  * Google Cheza device tree source (common between revisions)
   4  *
   5  * Copyright 2018 Google LLC.
   6  */
   7
   8 #include <dt-bindings/gpio/gpio.h>
   9 #include <dt-bindings/input/input.h>
  10 #include <dt-bindings/regulator/qcom,rpmh-regulator.h>
  11 #include "sdm845.dtsi"
  12
  13 /* PMICs depend on spmi_bus label and so must come after SoC */
  14 #include "pm8005.dtsi"
  15 #include "pm8998.dtsi"
  16
  17 / {
  18         aliases {
  19                 bluetooth0 = &bluetooth;
  20                 hsuart0 = &uart6;
  21                 serial0 = &uart9;
  22                 wifi0 = &wifi;
  23         };
  24
  25         chosen {
  26                 stdout-path = "serial0:115200n8";
  27         };
  28
  29         backlight: backlight {
  30                 compatible = "pwm-backlight";
  31                 pwms = <&cros_ec_pwm 0>;
  32                 enable-gpios = <&tlmm 37 GPIO_ACTIVE_HIGH>;
  33                 power-supply = <&ppvar_sys>;
  34                 pinctrl-names = "default";
  35                 pinctrl-0 = <&ap_edp_bklten>;
  36         };
  37
  38         /* FIXED REGULATORS - parents above children */
  39
  40         /* This is the top level supply and variable voltage */
  41         ppvar_sys: ppvar-sys-regulator {
  42                 compatible = "regulator-fixed";
  43                 regulator-name = "ppvar_sys";
  44                 regulator-always-on;
  45                 regulator-boot-on;
  46         };
  47
  48         /* This divides ppvar_sys by 2, so voltage is variable */
  49         src_vph_pwr: src-vph-pwr-regulator {
  50                 compatible = "regulator-fixed";
  51                 regulator-name = "src_vph_pwr";
  52
  53                 /* EC turns on with switchcap_on_l; always on for AP */
  54                 regulator-always-on;
  55                 regulator-boot-on;
  56
  57                 vin-supply = <&ppvar_sys>;
  58         };
  59
  60         pp5000_a: pp5000-a-regulator {
  61                 compatible = "regulator-fixed";
  62                 regulator-name = "pp5000_a";
  63
  64                 /* EC turns on with en_pp5000_a; always on for AP */
  65                 regulator-always-on;
  66                 regulator-boot-on;
  67                 regulator-min-microvolt = <5000000>;
  68                 regulator-max-microvolt = <5000000>;
  69
  70                 vin-supply = <&ppvar_sys>;
  71         };
  72
  73         src_vreg_bob: src-vreg-bob-regulator {
  74                 compatible = "regulator-fixed";
  75                 regulator-name = "src_vreg_bob";
  76
  77                 /* EC turns on with vbob_en; always on for AP */
  78                 regulator-always-on;
  79                 regulator-boot-on;
  80                 regulator-min-microvolt = <3600000>;
  81                 regulator-max-microvolt = <3600000>;
  82
  83                 vin-supply = <&ppvar_sys>;
  84         };
  85
  86         pp3300_dx_edp: pp3300-dx-edp-regulator {
  87                 compatible = "regulator-fixed";
  88                 regulator-name = "pp3300_dx_edp";
  89
  90                 regulator-min-microvolt = <3300000>;
  91                 regulator-max-microvolt = <3300000>;
  92
  93                 gpio = <&tlmm 43 GPIO_ACTIVE_HIGH>;
  94                 enable-active-high;
  95                 pinctrl-names = "default";
  96                 pinctrl-0 = <&en_pp3300_dx_edp>;
  97         };
  98
  99         /*
 100          * Apparently RPMh does not provide support for PM8998 S4 because it
 101          * is always-on; model it as a fixed regulator.
 102          */
 103         src_pp1800_s4a: pm8998-smps4 {
 104                 compatible = "regulator-fixed";
 105                 regulator-name = "src_pp1800_s4a";
 106
 107                 regulator-min-microvolt = <1800000>;
 108                 regulator-max-microvolt = <1800000>;
 109
 110                 regulator-always-on;
 111                 regulator-boot-on;
 112
 113                 vin-supply = <&src_vph_pwr>;
 114         };
 115
 116         /* BOARD-SPECIFIC TOP LEVEL NODES */
 117
 118         gpio-keys {
 119                 compatible = "gpio-keys";
 120                 pinctrl-names = "default";
 121                 pinctrl-0 = <&pen_eject_odl>;
 122
 123                 pen-insert {
 124                         label = "Pen Insert";
 125                         /* Insert = low, eject = high */
 126                         gpios = <&tlmm 119 GPIO_ACTIVE_LOW>;
 127                         linux,code = <SW_PEN_INSERTED>;
 128                         linux,input-type = <EV_SW>;
 129                         wakeup-source;
 130                 };
 131         };
 132
 133         panel: panel {
 134                 compatible ="innolux,p120zdg-bf1";
 135                 power-supply = <&pp3300_dx_edp>;
 136                 backlight = <&backlight>;
 137                 no-hpd;
 138
 139                 ports {
 140                         panel_in: port {
 141                                 panel_in_edp: endpoint {
 142                                         remote-endpoint = <&sn65dsi86_out>;
 143                                 };
 144                         };
 145                 };
 146         };
 147 };
 148
 149 /*
 150  * Reserved memory changes
 151  *
 152  * Putting this all together (out of order with the rest of the file) to keep
 153  * all modifications to the memory map (from sdm845.dtsi) in one place.
 154  */
 155
 156 /*
 157  * Our mpss_region is 8MB bigger than the default one and that conflicts
 158  * with venus_mem and cdsp_mem.
 159  *
 160  * For venus_mem we'll delete and re-create at a different address.
 161  *
 162  * cdsp_mem isn't used on cheza right now so we won't bother re-creating it; but
 163  * that also means we need to delete cdsp_pas.
 164  */
 165 /delete-node/ &venus_mem;
 166 /delete-node/ &cdsp_mem;
 167 /delete-node/ &cdsp_pas;
 168 /delete-node/ &zap_shader;
 169 /delete-node/ &gpu_mem;
 170
 171 /* Increase the size from 120 MB to 128 MB */
 172 &mpss_region {
 173         reg = <0 0x8e000000 0 0x8000000>;
 174 };
 175
 176 /* Increase the size from 2MB to 8MB */
 177 &rmtfs_mem {
 178         reg = <0 0x88f00000 0 0x800000>;
 179 };
 180
 181 / {
 182         reserved-memory {
 183                 venus_mem: memory@96000000 {
 184                         reg = <0 0x96000000 0 0x500000>;
 185                         no-map;
 186                 };
 187         };
 188 };
 189
 190 &qspi {
 191         status = "okay";
 192         pinctrl-names = "default";
 193         pinctrl-0 = <&qspi_clk &qspi_cs0 &qspi_data01>;
 194
 195         flash@0 {
 196                 compatible = "jedec,spi-nor";
 197                 reg = <0>;
 198
 199                 /*
 200                  * In theory chip supports up to 104 MHz and controller up
 201                  * to 80 MHz, but above 25 MHz wasn't reliable so we'll use
 202                  * that for now.  b:117440651
 203                  */
 204                 spi-max-frequency = <25000000>;
 205                 spi-tx-bus-width = <2>;
 206                 spi-rx-bus-width = <2>;
 207         };
 208 };
 209
 210
 211 &apps_rsc {
 212         pm8998-rpmh-regulators {
 213                 compatible = "qcom,pm8998-rpmh-regulators";
 214                 qcom,pmic-id = "a";
 215
 216                 vdd-s1-supply = <&src_vph_pwr>;
 217                 vdd-s2-supply = <&src_vph_pwr>;
 218                 vdd-s3-supply = <&src_vph_pwr>;
 219                 vdd-s4-supply = <&src_vph_pwr>;
 220                 vdd-s5-supply = <&src_vph_pwr>;
 221                 vdd-s6-supply = <&src_vph_pwr>;
 222                 vdd-s7-supply = <&src_vph_pwr>;
 223                 vdd-s8-supply = <&src_vph_pwr>;
 224                 vdd-s9-supply = <&src_vph_pwr>;
 225                 vdd-s10-supply = <&src_vph_pwr>;
 226                 vdd-s11-supply = <&src_vph_pwr>;
 227                 vdd-s12-supply = <&src_vph_pwr>;
 228                 vdd-s13-supply = <&src_vph_pwr>;
 229                 vdd-l1-l27-supply = <&src_pp1025_s7a>;
 230                 vdd-l2-l8-l17-supply = <&src_pp1350_s3a>;
 231                 vdd-l3-l11-supply = <&src_pp1025_s7a>;
 232                 vdd-l4-l5-supply = <&src_pp1025_s7a>;
 233                 vdd-l6-supply = <&src_vph_pwr>;
 234                 vdd-l7-l12-l14-l15-supply = <&src_pp2040_s5a>;
 235                 vdd-l9-supply = <&src_pp2040_s5a>;
 236                 vdd-l10-l23-l25-supply = <&src_vreg_bob>;
 237                 vdd-l13-l19-l21-supply = <&src_vreg_bob>;
 238                 vdd-l16-l28-supply = <&src_vreg_bob>;
 239                 vdd-l18-l22-supply = <&src_vreg_bob>;
 240                 vdd-l20-l24-supply = <&src_vreg_bob>;
 241                 vdd-l26-supply = <&src_pp1350_s3a>;
 242                 vin-lvs-1-2-supply = <&src_pp1800_s4a>;
 243
 244                 src_pp1125_s2a: smps2 {
 245                         regulator-min-microvolt = <1100000>;
 246                         regulator-max-microvolt = <1100000>;
 247                 };
 248
 249                 src_pp1350_s3a: smps3 {
 250                         regulator-min-microvolt = <1352000>;
 251                         regulator-max-microvolt = <1352000>;
 252                 };
 253
 254                 src_pp2040_s5a: smps5 {
 255                         regulator-min-microvolt = <1904000>;
 256                         regulator-max-microvolt = <2040000>;
 257                 };
 258
 259                 src_pp1025_s7a: smps7 {
 260                         regulator-min-microvolt = <900000>;
 261                         regulator-max-microvolt = <1028000>;
 262                 };
 263
 264                 vdd_qusb_hs0:
 265                 vdda_hp_pcie_core:
 266                 vdda_mipi_csi0_0p9:
 267                 vdda_mipi_csi1_0p9:
 268                 vdda_mipi_csi2_0p9:
 269                 vdda_mipi_dsi0_pll:
 270                 vdda_mipi_dsi1_pll:
 271                 vdda_qlink_lv:
 272                 vdda_qlink_lv_ck:
 273                 vdda_qrefs_0p875:
 274                 vdda_pcie_core:
 275                 vdda_pll_cc_ebi01:
 276                 vdda_pll_cc_ebi23:
 277                 vdda_sp_sensor:
 278                 vdda_ufs1_core:
 279                 vdda_ufs2_core:
 280                 vdda_usb1_ss_core:
 281                 vdda_usb2_ss_core:
 282                 src_pp875_l1a: ldo1 {
 283                         regulator-min-microvolt = <880000>;
 284                         regulator-max-microvolt = <880000>;
 285                         regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
 286                 };
 287
 288                 vddpx_10:
 289                 src_pp1200_l2a: ldo2 {
 290                         regulator-min-microvolt = <1200000>;
 291                         regulator-max-microvolt = <1200000>;
 292                         regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
 293
 294                         /* TODO: why??? */
 295                         regulator-always-on;
 296                 };
 297
 298                 pp1000_l3a_sdr845: ldo3 {
 299                         regulator-min-microvolt = <1000000>;
 300                         regulator-max-microvolt = <1000000>;
 301                         regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
 302                 };
 303
 304                 vdd_wcss_cx:
 305                 vdd_wcss_mx:
 306                 vdda_wcss_pll:
 307                 src_pp800_l5a: ldo5 {
 308                         regulator-min-microvolt = <800000>;
 309                         regulator-max-microvolt = <800000>;
 310                         regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
 311                 };
 312
 313                 vddpx_13:
 314                 src_pp1800_l6a: ldo6 {
 315                         regulator-min-microvolt = <1856000>;
 316                         regulator-max-microvolt = <1856000>;
 317                         regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
 318                 };
 319
 320                 pp1800_l7a_wcn3990: ldo7 {
 321                         regulator-min-microvolt = <1800000>;
 322                         regulator-max-microvolt = <1800000>;
 323                         regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
 324                 };
 325
 326                 src_pp1200_l8a: ldo8 {
 327                         regulator-min-microvolt = <1200000>;
 328                         regulator-max-microvolt = <1248000>;
 329                         regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
 330                 };
 331
 332                 pp1800_dx_pen:
 333                 src_pp1800_l9a: ldo9 {
 334                         regulator-min-microvolt = <1800000>;
 335                         regulator-max-microvolt = <1800000>;
 336                         regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
 337                 };
 338
 339                 src_pp1800_l10a: ldo10 {
 340                         regulator-min-microvolt = <1800000>;
 341                         regulator-max-microvolt = <1800000>;
 342                         regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
 343                 };
 344
 345                 pp1000_l11a_sdr845: ldo11 {
 346                         regulator-min-microvolt = <1000000>;
 347                         regulator-max-microvolt = <1048000>;
 348                         regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
 349                 };
 350
 351                 vdd_qfprom:
 352                 vdd_qfprom_sp:
 353                 vdda_apc1_cs_1p8:
 354                 vdda_gfx_cs_1p8:
 355                 vdda_qrefs_1p8:
 356                 vdda_qusb_hs0_1p8:
 357                 vddpx_11:
 358                 src_pp1800_l12a: ldo12 {
 359                         regulator-min-microvolt = <1800000>;
 360                         regulator-max-microvolt = <1800000>;
 361                         regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
 362                 };
 363
 364                 vddpx_2:
 365                 src_pp2950_l13a: ldo13 {
 366                         regulator-min-microvolt = <1800000>;
 367                         regulator-max-microvolt = <2960000>;
 368                         regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
 369                 };
 370
 371                 src_pp1800_l14a: ldo14 {
 372                         regulator-min-microvolt = <1800000>;
 373                         regulator-max-microvolt = <1800000>;
 374                         regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
 375                 };
 376
 377                 src_pp1800_l15a: ldo15 {
 378                         regulator-min-microvolt = <1800000>;
 379                         regulator-max-microvolt = <1800000>;
 380                         regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
 381                 };
 382
 383                 pp2700_l16a: ldo16 {
 384                         regulator-min-microvolt = <2704000>;
 385                         regulator-max-microvolt = <2704000>;
 386                         regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
 387                 };
 388
 389                 src_pp1300_l17a: ldo17 {
 390                         regulator-min-microvolt = <1304000>;
 391                         regulator-max-microvolt = <1304000>;
 392                         regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
 393                 };
 394
 395                 pp2700_l18a: ldo18 {
 396                         regulator-min-microvolt = <2704000>;
 397                         regulator-max-microvolt = <2960000>;
 398                         regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
 399                 };
 400
 401                 /*
 402                  * NOTE: this rail should have been called
 403                  * src_pp3300_l19a in the schematic
 404                  */
 405                 src_pp3000_l19a: ldo19 {
 406                         regulator-min-microvolt = <3304000>;
 407                         regulator-max-microvolt = <3304000>;
 408
 409                         regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
 410                 };
 411
 412                 src_pp2950_l20a: ldo20 {
 413                         regulator-min-microvolt = <2704000>;
 414                         regulator-max-microvolt = <2960000>;
 415                         regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
 416                 };
 417
 418                 src_pp2950_l21a: ldo21 {
 419                         regulator-min-microvolt = <2704000>;
 420                         regulator-max-microvolt = <2960000>;
 421                         regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
 422                 };
 423
 424                 pp3300_hub:
 425                 src_pp3300_l22a: ldo22 {
 426                         regulator-min-microvolt = <3304000>;
 427                         regulator-max-microvolt = <3304000>;
 428                         regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
 429                         /*
 430                          * HACK: Should add a usb hub node and driver
 431                          * to turn this on and off at suspend/resume time
 432                          */
 433                         regulator-boot-on;
 434                         regulator-always-on;
 435                 };
 436
 437                 pp3300_l23a_ch1_wcn3990: ldo23 {
 438                         regulator-min-microvolt = <3000000>;
 439                         regulator-max-microvolt = <3312000>;
 440                         regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
 441                 };
 442
 443                 vdda_qusb_hs0_3p1:
 444                 src_pp3075_l24a: ldo24 {
 445                         regulator-min-microvolt = <3088000>;
 446                         regulator-max-microvolt = <3088000>;
 447                         regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
 448                 };
 449
 450                 pp3300_l25a_ch0_wcn3990: ldo25 {
 451                         regulator-min-microvolt = <3304000>;
 452                         regulator-max-microvolt = <3304000>;
 453                         regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
 454                 };
 455
 456                 pp1200_hub:
 457                 vdda_hp_pcie_1p2:
 458                 vdda_hv_ebi0:
 459                 vdda_hv_ebi1:
 460                 vdda_hv_ebi2:
 461                 vdda_hv_ebi3:
 462                 vdda_mipi_csi_1p25:
 463                 vdda_mipi_dsi0_1p2:
 464                 vdda_mipi_dsi1_1p2:
 465                 vdda_pcie_1p2:
 466                 vdda_ufs1_1p2:
 467                 vdda_ufs2_1p2:
 468                 vdda_usb1_ss_1p2:
 469                 vdda_usb2_ss_1p2:
 470                 src_pp1200_l26a: ldo26 {
 471                         regulator-min-microvolt = <1200000>;
 472                         regulator-max-microvolt = <1200000>;
 473                         regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
 474                 };
 475
 476                 pp3300_dx_pen:
 477                 src_pp3300_l28a: ldo28 {
 478                         regulator-min-microvolt = <3304000>;
 479                         regulator-max-microvolt = <3304000>;
 480                         regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
 481                 };
 482
 483                 src_pp1800_lvs1: lvs1 {
 484                         regulator-min-microvolt = <1800000>;
 485                         regulator-max-microvolt = <1800000>;
 486                 };
 487
 488                 src_pp1800_lvs2: lvs2 {
 489                         regulator-min-microvolt = <1800000>;
 490                         regulator-max-microvolt = <1800000>;
 491                 };
 492         };
 493
 494         pm8005-rpmh-regulators {
 495                 compatible = "qcom,pm8005-rpmh-regulators";
 496                 qcom,pmic-id = "c";
 497
 498                 vdd-s1-supply = <&src_vph_pwr>;
 499                 vdd-s2-supply = <&src_vph_pwr>;
 500                 vdd-s3-supply = <&src_vph_pwr>;
 501                 vdd-s4-supply = <&src_vph_pwr>;
 502
 503                 src_pp600_s3c: smps3 {
 504                         regulator-min-microvolt = <600000>;
 505                         regulator-max-microvolt = <600000>;
 506                 };
 507         };
 508 };
 509
 510 &dsi0 {
 511         status = "okay";
 512         vdda-supply = <&vdda_mipi_dsi0_1p2>;
 513
 514         ports {
 515                 port@1 {
 516                         endpoint {
 517                                 remote-endpoint = <&sn65dsi86_in>;
 518                                 data-lanes = <0 1 2 3>;
 519                         };
 520                 };
 521         };
 522 };
 523
 524 &dsi0_phy {
 525         status = "okay";
 526         vdds-supply = <&vdda_mipi_dsi0_pll>;
 527 };
 528
 529 edp_brij_i2c: &i2c3 {
 530         status = "okay";
 531         clock-frequency = <400000>;
 532
 533         sn65dsi86_bridge: bridge@2d {
 534                 compatible = "ti,sn65dsi86";
 535                 reg = <0x2d>;
 536                 pinctrl-names = "default";
 537                 pinctrl-0 = <&edp_brij_en &edp_brij_irq>;
 538
 539                 interrupt-parent = <&tlmm>;
 540                 interrupts = <10 IRQ_TYPE_LEVEL_HIGH>;
 541
 542                 enable-gpios = <&tlmm 102 GPIO_ACTIVE_HIGH>;
 543
 544                 vpll-supply = <&src_pp1800_s4a>;
 545                 vccio-supply = <&src_pp1800_s4a>;
 546                 vcca-supply = <&src_pp1200_l2a>;
 547                 vcc-supply = <&src_pp1200_l2a>;
 548
 549                 clocks = <&rpmhcc RPMH_LN_BB_CLK2>;
 550                 clock-names = "refclk";
 551
 552                 ports {
 553                         #address-cells = <1>;
 554                         #size-cells = <0>;
 555
 556                         port@0 {
 557                                 reg = <0>;
 558                                 sn65dsi86_in: endpoint {
 559                                         remote-endpoint = <&dsi0_out>;
 560                                 };
 561                         };
 562
 563                         port@1 {
 564                                 reg = <1>;
 565                                 sn65dsi86_out: endpoint {
 566                                         remote-endpoint = <&panel_in_edp>;
 567                                 };
 568                         };
 569                 };
 570         };
 571 };
 572
 573 ap_pen_1v8: &i2c11 {
 574         status = "okay";
 575         clock-frequency = <400000>;
 576
 577         digitizer@9 {
 578                 compatible = "wacom,w9013", "hid-over-i2c";
 579                 reg = <0x9>;
 580                 pinctrl-names = "default";
 581                 pinctrl-0 = <&pen_irq_l>, <&pen_pdct_l>, <&pen_rst_l>;
 582
 583                 vdd-supply = <&pp3300_dx_pen>;
 584                 vddl-supply = <&pp1800_dx_pen>;
 585                 post-power-on-delay-ms = <100>;
 586
 587                 interrupt-parent = <&tlmm>;
 588                 interrupts = <24 IRQ_TYPE_LEVEL_LOW>;
 589
 590                 hid-descr-addr = <0x1>;
 591         };
 592 };
 593
 594 amp_i2c: &i2c12 {
 595         status = "okay";
 596         clock-frequency = <400000>;
 597 };
 598
 599 ap_ts_i2c: &i2c14 {
 600         status = "okay";
 601         clock-frequency = <400000>;
 602
 603         touchscreen@10 {
 604                 compatible = "elan,ekth3500";
 605                 reg = <0x10>;
 606                 pinctrl-names = "default";
 607                 pinctrl-0 = <&ts_int_l &ts_reset_l>;
 608
 609                 interrupt-parent = <&tlmm>;
 610                 interrupts = <125 IRQ_TYPE_LEVEL_LOW>;
 611
 612                 vcc33-supply = <&src_pp3300_l28a>;
 613
 614                 reset-gpios = <&tlmm 118 GPIO_ACTIVE_LOW>;
 615         };
 616 };
 617
 618 &lpasscc {
 619         status = "okay";
 620 };
 621
 622 &mdss {
 623         status = "okay";
 624 };
 625
 626 &mdss_mdp {
 627         status = "okay";
 628 };
 629
 630 &qupv3_id_0 {
 631         status = "okay";
 632 };
 633
 634 &qupv3_id_1 {
 635         status = "okay";
 636 };
 637
 638 &sdhc_2 {
 639         status = "okay";
 640
 641         pinctrl-names = "default";
 642         pinctrl-0 = <&sdc2_clk &sdc2_cmd &sdc2_data &sd_cd_odl>;
 643
 644         vmmc-supply = <&src_pp2950_l21a>;
 645         vqmmc-supply = <&vddpx_2>;
 646
 647         cd-gpios = <&tlmm 44 GPIO_ACTIVE_LOW>;
 648 };
 649
 650 &spi0 {
 651         status = "okay";
 652 };
 653
 654 &spi10 {
 655         status = "okay";
 656
 657         cros_ec: ec@0 {
 658                 compatible = "google,cros-ec-spi";
 659                 reg = <0>;
 660                 interrupt-parent = <&tlmm>;
 661                 interrupts = <122 IRQ_TYPE_LEVEL_LOW>;
 662                 pinctrl-names = "default";
 663                 pinctrl-0 = <&ec_ap_int_l>;
 664                 spi-max-frequency = <3000000>;
 665
 666                 cros_ec_pwm: ec-pwm {
 667                         compatible = "google,cros-ec-pwm";
 668                         #pwm-cells = <1>;
 669                 };
 670
 671                 i2c_tunnel: i2c-tunnel {
 672                         compatible = "google,cros-ec-i2c-tunnel";
 673                         google,remote-bus = <0>;
 674                         #address-cells = <1>;
 675                         #size-cells = <0>;
 676                 };
 677
 678                 pdupdate {
 679                         compatible = "google,cros-ec-pd-update";
 680                 };
 681         };
 682 };
 683
 684 #include <arm/cros-ec-keyboard.dtsi>
 685 #include <arm/cros-ec-sbs.dtsi>
 686
 687 &uart6 {
 688         status = "okay";
 689
 690         bluetooth: wcn3990-bt {
 691                 compatible = "qcom,wcn3990-bt";
 692                 vddio-supply = <&src_pp1800_s4a>;
 693                 vddxo-supply = <&pp1800_l7a_wcn3990>;
 694                 vddrf-supply = <&src_pp1300_l17a>;
 695                 vddch0-supply = <&pp3300_l25a_ch0_wcn3990>;
 696                 max-speed = <3200000>;
 697         };
 698 };
 699
 700 &uart9 {
 701         status = "okay";
 702 };
 703
 704 &ufs_mem_hc {
 705         status = "okay";
 706
 707         reset-gpios = <&tlmm 150 GPIO_ACTIVE_LOW>;
 708
 709         vcc-supply = <&src_pp2950_l20a>;
 710         vcc-max-microamp = <600000>;
 711 };
 712
 713 &ufs_mem_phy {
 714         status = "okay";
 715
 716         vdda-phy-supply = <&vdda_ufs1_core>;
 717         vdda-pll-supply = <&vdda_ufs1_1p2>;
 718 };
 719
 720 &usb_1 {
 721         status = "okay";
 722
 723         /* We'll use this as USB 2.0 only */
 724         qcom,select-utmi-as-pipe-clk;
 725 };
 726
 727 &usb_1_dwc3 {
 728         /*
 729          * The hardware design intends this port to be hooked up in peripheral
 730          * mode, so we'll hardcode it here.  Some details:
 731          * - SDM845 expects only a single Type C connector so it has only one
 732          *   native Type C port but cheza has two Type C connectors.
 733          * - The only source of DP is the single native Type C port.
 734          * - On cheza we want to be able to hook DP up to _either_ of the
 735          *   two Type C connectors and want to be able to achieve 4 lanes of DP.
 736          * - When you configure a Type C port for 4 lanes of DP you lose USB3.
 737          * - In order to make everything work, the native Type C port is always
 738          *   configured as 4-lanes DP so it's always available.
 739          * - The extra USB3 port on SDM845 goes to a USB 3 hub which is then
 740          *   sent to the two Type C connectors.
 741          * - The extra USB2 lines from the native Type C port are always
 742          *   setup as "peripheral" so that we can mux them over to one connector
 743          *   or the other if someone needs the connector configured as a gadget
 744          *   (but they only get USB2 speeds).
 745          *
 746          * All the hardware muxes would allow us to hook things up in different
 747          * ways to some potential benefit for static configurations (you could
 748          * achieve extra USB2 bandwidth by using two different ports for the
 749          * two connectors or possibly even get USB3 peripheral mode), but in
 750          * each case you end up forcing to disconnect/reconnect an in-use
 751          * USB session in some cases depending on what you hotplug into the
 752          * other connector.  Thus hardcoding this as peripheral makes sense.
 753          */
 754         dr_mode = "peripheral";
 755
 756         /*
 757          * We always need the high speed pins as 4-lanes DP in case someone
 758          * hotplugs a DP peripheral.  Thus limit this port to a max of high
 759          * speed.
 760          */
 761         maximum-speed = "high-speed";
 762
 763         /*
 764          * We don't need the usb3-phy since we run in highspeed mode always, so
 765          * re-define these properties removing the superspeed USB PHY reference.
 766          */
 767         phys = <&usb_1_hsphy>;
 768         phy-names = "usb2-phy";
 769 };
 770
 771 &usb_1_hsphy {
 772         status = "okay";
 773
 774         vdd-supply = <&vdda_usb1_ss_core>;
 775         vdda-pll-supply = <&vdda_qusb_hs0_1p8>;
 776         vdda-phy-dpdm-supply = <&vdda_qusb_hs0_3p1>;
 777
 778         qcom,imp-res-offset-value = <8>;
 779         qcom,hstx-trim-value = <QUSB2_V2_HSTX_TRIM_21_6_MA>;
 780         qcom,preemphasis-level = <QUSB2_V2_PREEMPHASIS_5_PERCENT>;
 781         qcom,preemphasis-width = <QUSB2_V2_PREEMPHASIS_WIDTH_HALF_BIT>;
 782 };
 783
 784 &usb_2 {
 785         status = "okay";
 786 };
 787
 788 &usb_2_dwc3 {
 789         /* We have this hooked up to a hub and we always use in host mode */
 790         dr_mode = "host";
 791 };
 792
 793 &usb_2_hsphy {
 794         status = "okay";
 795
 796         vdd-supply = <&vdda_usb2_ss_core>;
 797         vdda-pll-supply = <&vdda_qusb_hs0_1p8>;
 798         vdda-phy-dpdm-supply = <&vdda_qusb_hs0_3p1>;
 799
 800         qcom,imp-res-offset-value = <8>;
 801         qcom,hstx-trim-value = <QUSB2_V2_HSTX_TRIM_22_8_MA>;
 802 };
 803
 804 &usb_2_qmpphy {
 805         status = "okay";
 806
 807         vdda-phy-supply = <&vdda_usb2_ss_1p2>;
 808         vdda-pll-supply = <&vdda_usb2_ss_core>;
 809 };
 810
 811 &wifi {
 812         status = "okay";
 813
 814         vdd-0.8-cx-mx-supply = <&src_pp800_l5a >;
 815         vdd-1.8-xo-supply = <&pp1800_l7a_wcn3990>;
 816         vdd-1.3-rfa-supply = <&src_pp1300_l17a>;
 817         vdd-3.3-ch0-supply = <&pp3300_l25a_ch0_wcn3990>;
 818 };
 819
 820 /* PINCTRL - additions to nodes defined in sdm845.dtsi */
 821
 822 &qspi_cs0 {
 823         pinconf {
 824                 pins = "gpio90";
 825                 bias-disable;
 826         };
 827 };
 828
 829 &qspi_clk {
 830         pinconf {
 831                 pins = "gpio95";
 832                 bias-disable;
 833         };
 834 };
 835
 836 &qspi_data01 {
 837         pinconf {
 838                 pins = "gpio91", "gpio92";
 839
 840                 /* High-Z when no transfers; nice to park the lines */
 841                 bias-pull-up;
 842         };
 843 };
 844
 845 &qup_i2c3_default {
 846         pinconf {
 847                 pins = "gpio41", "gpio42";
 848                 drive-strength = <2>;
 849
 850                 /* Has external pullup */
 851                 bias-disable;
 852         };
 853 };
 854
 855 &qup_i2c11_default {
 856         pinconf {
 857                 pins = "gpio31", "gpio32";
 858                 drive-strength = <2>;
 859
 860                 /* Has external pullup */
 861                 bias-disable;
 862         };
 863 };
 864
 865 &qup_i2c12_default {
 866         pinconf {
 867                 pins = "gpio49", "gpio50";
 868                 drive-strength = <2>;
 869
 870                 /* Has external pullup */
 871                 bias-disable;
 872         };
 873 };
 874
 875 &qup_i2c14_default {
 876         pinconf {
 877                 pins = "gpio33", "gpio34";
 878                 drive-strength = <2>;
 879
 880                 /* Has external pullup */
 881                 bias-disable;
 882         };
 883 };
 884
 885 &qup_spi0_default {
 886         pinconf {
 887                 pins = "gpio0", "gpio1", "gpio2", "gpio3";
 888                 drive-strength = <2>;
 889                 bias-disable;
 890         };
 891 };
 892
 893 &qup_spi5_default {
 894         pinconf {
 895                 pins = "gpio85", "gpio86", "gpio87", "gpio88";
 896                 drive-strength = <2>;
 897                 bias-disable;
 898         };
 899 };
 900
 901 &qup_spi10_default {
 902         pinconf {
 903                 pins = "gpio53", "gpio54", "gpio55", "gpio56";
 904                 drive-strength = <2>;
 905                 bias-disable;
 906         };
 907 };
 908
 909 &qup_uart6_default {
 910         /* Change pinmux to all 4 pins since CTS and RTS are connected */
 911         pinmux {
 912                 pins = "gpio45", "gpio46",
 913                        "gpio47", "gpio48";
 914         };
 915
 916         pinconf-cts {
 917                 /*
 918                  * Configure a pull-down on 45 (CTS) to match the pull of
 919                  * the Bluetooth module.
 920                  */
 921                 pins = "gpio45";
 922                 bias-pull-down;
 923         };
 924
 925         pinconf-rts-tx {
 926                 /* We'll drive 46 (RTS) and 47 (TX), so no pull */
 927                 pins = "gpio46", "gpio47";
 928                 drive-strength = <2>;
 929                 bias-disable;
 930         };
 931
 932         pinconf-rx {
 933                 /*
 934                  * Configure a pull-up on 48 (RX). This is needed to avoid
 935                  * garbage data when the TX pin of the Bluetooth module is
 936                  * in tri-state (module powered off or not driving the
 937                  * signal yet).
 938                  */
 939                 pins = "gpio48";
 940                 bias-pull-up;
 941         };
 942 };
 943
 944 &qup_uart9_default {
 945         pinconf-tx {
 946                 pins = "gpio4";
 947                 drive-strength = <2>;
 948                 bias-disable;
 949         };
 950
 951         pinconf-rx {
 952                 pins = "gpio5";
 953                 drive-strength = <2>;
 954                 bias-pull-up;
 955         };
 956 };
 957
 958 /* PINCTRL - board-specific pinctrl */
 959 &pm8005_gpio {
 960         gpio-line-names = "",
 961                           "",
 962                           "SLB",
 963                           "";
 964 };
 965
 966 &pm8998_adc {
 967         adc-chan@4d {
 968                 reg = <ADC5_AMUX_THM1_100K_PU>;
 969                 label = "sdm_temp";
 970         };
 971
 972         adc-chan@4e {
 973                 reg = <ADC5_AMUX_THM2_100K_PU>;
 974                 label = "quiet_temp";
 975         };
 976
 977         adc-chan@4f {
 978                 reg = <ADC5_AMUX_THM3_100K_PU>;
 979                 label = "lte_temp_1";
 980         };
 981
 982         adc-chan@50 {
 983                 reg = <ADC5_AMUX_THM4_100K_PU>;
 984                 label = "lte_temp_2";
 985         };
 986
 987         adc-chan@51 {
 988                 reg = <ADC5_AMUX_THM5_100K_PU>;
 989                 label = "charger_temp";
 990         };
 991 };
 992
 993 &pm8998_gpio {
 994         gpio-line-names = "",
 995                           "",
 996                           "SW_CTRL",
 997                           "",
 998                           "",
 999                           "",
1000                           "",
1001                           "",
1002                           "",
1003                           "",
1004                           "",
1005                           "",
1006                           "",
1007                           "",
1008                           "",
1009                           "",
1010                           "",
1011                           "",
1012                           "",
1013                           "",
1014                           "",
1015                           "CFG_OPT1",
1016                           "WCSS_PWR_REQ",
1017                           "",
1018                           "CFG_OPT2",
1019                           "SLB";
1020 };
1021
1022 &tlmm {
1023         /*
1024          * pinctrl settings for pins that have no real owners.
1025          */
1026         pinctrl-names = "default", "sleep";
1027         pinctrl-0 = <&bios_flash_wp_r_l>,
1028                     <&ap_suspend_l_deassert>;
1029
1030         pinctrl-1 = <&bios_flash_wp_r_l>,
1031                     <&ap_suspend_l_assert>;
1032
1033         /*
1034          * Hogs prevent usermode from changing the value. A GPIO can be both
1035          * here and in the pinctrl section.
1036          */
1037         ap-suspend-l-hog {
1038                 gpio-hog;
1039                 gpios = <126 GPIO_ACTIVE_LOW>;
1040                 output-low;
1041         };
1042
1043         ap_edp_bklten: ap-edp-bklten {
1044                 pinmux {
1045                         pins = "gpio37";
1046                         function = "gpio";
1047                 };
1048
1049                 pinconf {
1050                         pins = "gpio37";
1051                         drive-strength = <2>;
1052                         bias-disable;
1053                 };
1054         };
1055
1056         bios_flash_wp_r_l: bios-flash-wp-r-l {
1057                 pinmux {
1058                         pins = "gpio128";
1059                         function = "gpio";
1060                         input-enable;
1061                 };
1062
1063                 pinconf {
1064                         pins = "gpio128";
1065                         bias-disable;
1066                 };
1067         };
1068
1069         ec_ap_int_l: ec-ap-int-l {
1070                 pinmux {
1071                        pins = "gpio122";
1072                        function = "gpio";
1073                        input-enable;
1074                 };
1075
1076                 pinconf {
1077                        pins = "gpio122";
1078                        bias-pull-up;
1079                 };
1080         };
1081
1082         edp_brij_en: edp-brij-en {
1083                 pinmux {
1084                         pins = "gpio102";
1085                         function = "gpio";
1086                 };
1087
1088                 pinconf {
1089                         pins = "gpio102";
1090                         drive-strength = <2>;
1091                         bias-disable;
1092                 };
1093         };
1094
1095         edp_brij_irq: edp-brij-irq {
1096                 pinmux {
1097                         pins = "gpio10";
1098                         function = "gpio";
1099                 };
1100
1101                 pinconf {
1102                         pins = "gpio10";
1103                         drive-strength = <2>;
1104                         bias-pull-down;
1105                 };
1106         };
1107
1108         en_pp3300_dx_edp: en-pp3300-dx-edp {
1109                 pinmux {
1110                         pins = "gpio43";
1111                         function = "gpio";
1112                 };
1113
1114                 pinconf {
1115                         pins = "gpio43";
1116                         drive-strength = <2>;
1117                         bias-disable;
1118                 };
1119         };
1120
1121         h1_ap_int_odl: h1-ap-int-odl {
1122                 pinmux {
1123                         pins = "gpio129";
1124                         function = "gpio";
1125                         input-enable;
1126                 };
1127
1128                 pinconf {
1129                         pins = "gpio129";
1130                         bias-pull-up;
1131                 };
1132         };
1133
1134         pen_eject_odl: pen-eject-odl {
1135                 pinmux {
1136                         pins = "gpio119";
1137                         function = "gpio";
1138                         bias-pull-up;
1139                 };
1140         };
1141
1142         pen_irq_l: pen-irq-l {
1143                 pinmux {
1144                         pins = "gpio24";
1145                         function = "gpio";
1146                 };
1147
1148                 pinconf {
1149                         pins = "gpio24";
1150
1151                         /* Has external pullup */
1152                         bias-disable;
1153                 };
1154         };
1155
1156         pen_pdct_l: pen-pdct-l {
1157                 pinmux {
1158                         pins = "gpio63";
1159                         function = "gpio";
1160                 };
1161
1162                 pinconf {
1163                         pins = "gpio63";
1164
1165                         /* Has external pullup */
1166                         bias-disable;
1167                 };
1168         };
1169
1170         pen_rst_l: pen-rst-l {
1171                 pinmux  {
1172                         pins = "gpio23";
1173                         function = "gpio";
1174                 };
1175
1176                 pinconf {
1177                         pins = "gpio23";
1178                         bias-disable;
1179                         drive-strength = <2>;
1180
1181                         /*
1182                          * The pen driver doesn't currently support
1183                          * driving this reset line.  By specifying
1184                          * output-high here we're relying on the fact
1185                          * that this pin has a default pulldown at boot
1186                          * (which makes sure the pen was in reset if it
1187                          * was powered) and then we set it high here to
1188                          * take it out of reset.  Better would be if the
1189                          * pen driver could control this and we could
1190                          * remove "output-high" here.
1191                          */
1192                         output-high;
1193                 };
1194         };
1195
1196         sdc2_clk: sdc2-clk {
1197                 pinconf {
1198                         pins = "sdc2_clk";
1199                         bias-disable;
1200
1201                         /*
1202                          * It seems that mmc_test reports errors if drive
1203                          * strength is not 16.
1204                          */
1205                         drive-strength = <16>;
1206                 };
1207         };
1208
1209         sdc2_cmd: sdc2-cmd {
1210                 pinconf {
1211                         pins = "sdc2_cmd";
1212                         bias-pull-up;
1213                         drive-strength = <16>;
1214                 };
1215         };
1216
1217         sdc2_data: sdc2-data {
1218                 pinconf {
1219                         pins = "sdc2_data";
1220                         bias-pull-up;
1221                         drive-strength = <16>;
1222                 };
1223         };
1224
1225         sd_cd_odl: sd-cd-odl {
1226                 pinmux {
1227                         pins = "gpio44";
1228                         function = "gpio";
1229                 };
1230
1231                 pinconf {
1232                         pins = "gpio44";
1233                         bias-pull-up;
1234                 };
1235         };
1236
1237         ts_int_l: ts-int-l {
1238                 pinmux  {
1239                         pins = "gpio125";
1240                         function = "gpio";
1241                 };
1242
1243                 pinconf {
1244                         pins = "gpio125";
1245                         bias-pull-up;
1246                 };
1247         };
1248
1249         ts_reset_l: ts-reset-l {
1250                 pinmux  {
1251                         pins = "gpio118";
1252                         function = "gpio";
1253                 };
1254
1255                 pinconf {
1256                         pins = "gpio118";
1257                         bias-disable;
1258                         drive-strength = <2>;
1259                 };
1260         };
1261
1262         ap_suspend_l_assert: ap_suspend_l_assert {
1263                 config {
1264                         pins = "gpio126";
1265                         function = "gpio";
1266                         bias-no-pull;
1267                         drive-strength = <2>;
1268                         output-low;
1269                 };
1270         };
1271
1272         ap_suspend_l_deassert: ap_suspend_l_deassert {
1273                 config {
1274                         pins = "gpio126";
1275                         function = "gpio";
1276                         bias-no-pull;
1277                         drive-strength = <2>;
1278                         output-high;
1279                 };
1280         };
1281 };