treewide: remove redundant IS_ERR() before error code check

[linux/fpc-iii.git] / drivers / firmware / ti_sci.h

/* SPDX-License-Identifier: BSD-3-Clause */
/*
 * Texas Instruments System Control Interface (TISCI) Protocol
 *
 * Communication protocol with TI SCI hardware
 * The system works in a message response protocol
 * See: http://processors.wiki.ti.com/index.php/TISCI for details
 *
 * Copyright (C)  2015-2016 Texas Instruments Incorporated - http://www.ti.com/
 */

#ifndef __TI_SCI_H
#define __TI_SCI_H

/* Generic Messages */
#define TI_SCI_MSG_ENABLE_WDT   0x0000
#define TI_SCI_MSG_WAKE_RESET   0x0001
#define TI_SCI_MSG_VERSION      0x0002
#define TI_SCI_MSG_WAKE_REASON  0x0003
#define TI_SCI_MSG_GOODBYE      0x0004
#define TI_SCI_MSG_SYS_RESET    0x0005

/* Device requests */
#define TI_SCI_MSG_SET_DEVICE_STATE     0x0200
#define TI_SCI_MSG_GET_DEVICE_STATE     0x0201
#define TI_SCI_MSG_SET_DEVICE_RESETS    0x0202

/* Clock requests */
#define TI_SCI_MSG_SET_CLOCK_STATE      0x0100
#define TI_SCI_MSG_GET_CLOCK_STATE      0x0101
#define TI_SCI_MSG_SET_CLOCK_PARENT     0x0102
#define TI_SCI_MSG_GET_CLOCK_PARENT     0x0103
#define TI_SCI_MSG_GET_NUM_CLOCK_PARENTS 0x0104
#define TI_SCI_MSG_SET_CLOCK_FREQ       0x010c
#define TI_SCI_MSG_QUERY_CLOCK_FREQ     0x010d
#define TI_SCI_MSG_GET_CLOCK_FREQ       0x010e

/* Resource Management Requests */
#define TI_SCI_MSG_GET_RESOURCE_RANGE   0x1500

/* IRQ requests */
#define TI_SCI_MSG_SET_IRQ              0x1000
#define TI_SCI_MSG_FREE_IRQ             0x1001

/* NAVSS resource management */
/* Ringacc requests */
#define TI_SCI_MSG_RM_RING_ALLOCATE             0x1100
#define TI_SCI_MSG_RM_RING_FREE                 0x1101
#define TI_SCI_MSG_RM_RING_RECONFIG             0x1102
#define TI_SCI_MSG_RM_RING_RESET                0x1103
#define TI_SCI_MSG_RM_RING_CFG                  0x1110
#define TI_SCI_MSG_RM_RING_GET_CFG              0x1111

/* PSI-L requests */
#define TI_SCI_MSG_RM_PSIL_PAIR                 0x1280
#define TI_SCI_MSG_RM_PSIL_UNPAIR               0x1281

#define TI_SCI_MSG_RM_UDMAP_TX_ALLOC            0x1200
#define TI_SCI_MSG_RM_UDMAP_TX_FREE             0x1201
#define TI_SCI_MSG_RM_UDMAP_RX_ALLOC            0x1210
#define TI_SCI_MSG_RM_UDMAP_RX_FREE             0x1211
#define TI_SCI_MSG_RM_UDMAP_FLOW_CFG            0x1220
#define TI_SCI_MSG_RM_UDMAP_OPT_FLOW_CFG        0x1221

#define TISCI_MSG_RM_UDMAP_TX_CH_CFG            0x1205
#define TISCI_MSG_RM_UDMAP_TX_CH_GET_CFG        0x1206
#define TISCI_MSG_RM_UDMAP_RX_CH_CFG            0x1215
#define TISCI_MSG_RM_UDMAP_RX_CH_GET_CFG        0x1216
#define TISCI_MSG_RM_UDMAP_FLOW_CFG             0x1230
#define TISCI_MSG_RM_UDMAP_FLOW_SIZE_THRESH_CFG 0x1231
#define TISCI_MSG_RM_UDMAP_FLOW_GET_CFG         0x1232
#define TISCI_MSG_RM_UDMAP_FLOW_SIZE_THRESH_GET_CFG     0x1233

/* Processor Control requests */
#define TI_SCI_MSG_PROC_REQUEST         0xc000
#define TI_SCI_MSG_PROC_RELEASE         0xc001
#define TI_SCI_MSG_PROC_HANDOVER        0xc005
#define TI_SCI_MSG_SET_CONFIG           0xc100
#define TI_SCI_MSG_SET_CTRL             0xc101
#define TI_SCI_MSG_GET_STATUS           0xc400

/**
 * struct ti_sci_msg_hdr - Generic Message Header for All messages and responses
 * @type:       Type of messages: One of TI_SCI_MSG* values
 * @host:       Host of the message
 * @seq:        Message identifier indicating a transfer sequence
 * @flags:      Flag for the message
 */
struct ti_sci_msg_hdr {
        u16 type;
        u8 host;
        u8 seq;
#define TI_SCI_MSG_FLAG(val)                    (1 << (val))
#define TI_SCI_FLAG_REQ_GENERIC_NORESPONSE      0x0
#define TI_SCI_FLAG_REQ_ACK_ON_RECEIVED         TI_SCI_MSG_FLAG(0)
#define TI_SCI_FLAG_REQ_ACK_ON_PROCESSED        TI_SCI_MSG_FLAG(1)
#define TI_SCI_FLAG_RESP_GENERIC_NACK           0x0
#define TI_SCI_FLAG_RESP_GENERIC_ACK            TI_SCI_MSG_FLAG(1)
        /* Additional Flags */
        u32 flags;
} __packed;

/**
 * struct ti_sci_msg_resp_version - Response for a message
 * @hdr:                Generic header
 * @firmware_description: String describing the firmware
 * @firmware_revision:  Firmware revision
 * @abi_major:          Major version of the ABI that firmware supports
 * @abi_minor:          Minor version of the ABI that firmware supports
 *
 * In general, ABI version changes follow the rule that minor version increments
 * are backward compatible. Major revision changes in ABI may not be
 * backward compatible.
 *
 * Response to a generic message with message type TI_SCI_MSG_VERSION
 */
struct ti_sci_msg_resp_version {
        struct ti_sci_msg_hdr hdr;
        char firmware_description[32];
        u16 firmware_revision;
        u8 abi_major;
        u8 abi_minor;
} __packed;

/**
 * struct ti_sci_msg_req_reboot - Reboot the SoC
 * @hdr:        Generic Header
 *
 * Request type is TI_SCI_MSG_SYS_RESET, responded with a generic
 * ACK/NACK message.
 */
struct ti_sci_msg_req_reboot {
        struct ti_sci_msg_hdr hdr;
} __packed;

/**
 * struct ti_sci_msg_req_set_device_state - Set the desired state of the device
 * @hdr:                Generic header
 * @id: Indicates which device to modify
 * @reserved: Reserved space in message, must be 0 for backward compatibility
 * @state: The desired state of the device.
 *
 * Certain flags can also be set to alter the device state:
 * + MSG_FLAG_DEVICE_WAKE_ENABLED - Configure the device to be a wake source.
 * The meaning of this flag will vary slightly from device to device and from
 * SoC to SoC but it generally allows the device to wake the SoC out of deep
 * suspend states.
 * + MSG_FLAG_DEVICE_RESET_ISO - Enable reset isolation for this device.
 * + MSG_FLAG_DEVICE_EXCLUSIVE - Claim this device exclusively. When passed
 * with STATE_RETENTION or STATE_ON, it will claim the device exclusively.
 * If another host already has this device set to STATE_RETENTION or STATE_ON,
 * the message will fail. Once successful, other hosts attempting to set
 * STATE_RETENTION or STATE_ON will fail.
 *
 * Request type is TI_SCI_MSG_SET_DEVICE_STATE, responded with a generic
 * ACK/NACK message.
 */
struct ti_sci_msg_req_set_device_state {
        /* Additional hdr->flags options */
#define MSG_FLAG_DEVICE_WAKE_ENABLED    TI_SCI_MSG_FLAG(8)
#define MSG_FLAG_DEVICE_RESET_ISO       TI_SCI_MSG_FLAG(9)
#define MSG_FLAG_DEVICE_EXCLUSIVE       TI_SCI_MSG_FLAG(10)
        struct ti_sci_msg_hdr hdr;
        u32 id;
        u32 reserved;

#define MSG_DEVICE_SW_STATE_AUTO_OFF    0
#define MSG_DEVICE_SW_STATE_RETENTION   1
#define MSG_DEVICE_SW_STATE_ON          2
        u8 state;
} __packed;

/**
 * struct ti_sci_msg_req_get_device_state - Request to get device.
 * @hdr:                Generic header
 * @id:         Device Identifier
 *
 * Request type is TI_SCI_MSG_GET_DEVICE_STATE, responded device state
 * information
 */
struct ti_sci_msg_req_get_device_state {
        struct ti_sci_msg_hdr hdr;
        u32 id;
} __packed;

/**
 * struct ti_sci_msg_resp_get_device_state - Response to get device request.
 * @hdr:                Generic header
 * @context_loss_count: Indicates how many times the device has lost context. A
 *      driver can use this monotonic counter to determine if the device has
 *      lost context since the last time this message was exchanged.
 * @resets: Programmed state of the reset lines.
 * @programmed_state:   The state as programmed by set_device.
 *                      - Uses the MSG_DEVICE_SW_* macros
 * @current_state:      The actual state of the hardware.
 *
 * Response to request TI_SCI_MSG_GET_DEVICE_STATE.
 */
struct ti_sci_msg_resp_get_device_state {
        struct ti_sci_msg_hdr hdr;
        u32 context_loss_count;
        u32 resets;
        u8 programmed_state;
#define MSG_DEVICE_HW_STATE_OFF         0
#define MSG_DEVICE_HW_STATE_ON          1
#define MSG_DEVICE_HW_STATE_TRANS       2
        u8 current_state;
} __packed;

/**
 * struct ti_sci_msg_req_set_device_resets - Set the desired resets
 *                              configuration of the device
 * @hdr:                Generic header
 * @id: Indicates which device to modify
 * @resets: A bit field of resets for the device. The meaning, behavior,
 *      and usage of the reset flags are device specific. 0 for a bit
 *      indicates releasing the reset represented by that bit while 1
 *      indicates keeping it held.
 *
 * Request type is TI_SCI_MSG_SET_DEVICE_RESETS, responded with a generic
 * ACK/NACK message.
 */
struct ti_sci_msg_req_set_device_resets {
        struct ti_sci_msg_hdr hdr;
        u32 id;
        u32 resets;
} __packed;

/**
 * struct ti_sci_msg_req_set_clock_state - Request to setup a Clock state
 * @hdr:        Generic Header, Certain flags can be set specific to the clocks:
 *              MSG_FLAG_CLOCK_ALLOW_SSC: Allow this clock to be modified
 *              via spread spectrum clocking.
 *              MSG_FLAG_CLOCK_ALLOW_FREQ_CHANGE: Allow this clock's
 *              frequency to be changed while it is running so long as it
 *              is within the min/max limits.
 *              MSG_FLAG_CLOCK_INPUT_TERM: Enable input termination, this
 *              is only applicable to clock inputs on the SoC pseudo-device.
 * @dev_id:     Device identifier this request is for
 * @clk_id:     Clock identifier for the device for this request.
 *              Each device has it's own set of clock inputs. This indexes
 *              which clock input to modify. Set to 255 if clock ID is
 *              greater than or equal to 255.
 * @request_state: Request the state for the clock to be set to.
 *              MSG_CLOCK_SW_STATE_UNREQ: The IP does not require this clock,
 *              it can be disabled, regardless of the state of the device
 *              MSG_CLOCK_SW_STATE_AUTO: Allow the System Controller to
 *              automatically manage the state of this clock. If the device
 *              is enabled, then the clock is enabled. If the device is set
 *              to off or retention, then the clock is internally set as not
 *              being required by the device.(default)
 *              MSG_CLOCK_SW_STATE_REQ:  Configure the clock to be enabled,
 *              regardless of the state of the device.
 * @clk_id_32:  Clock identifier for the device for this request.
 *              Only to be used if the clock ID is greater than or equal to
 *              255.
 *
 * Normally, all required clocks are managed by TISCI entity, this is used
 * only for specific control *IF* required. Auto managed state is
 * MSG_CLOCK_SW_STATE_AUTO, in other states, TISCI entity assume remote
 * will explicitly control.
 *
 * Request type is TI_SCI_MSG_SET_CLOCK_STATE, response is a generic
 * ACK or NACK message.
 */
struct ti_sci_msg_req_set_clock_state {
        /* Additional hdr->flags options */
#define MSG_FLAG_CLOCK_ALLOW_SSC                TI_SCI_MSG_FLAG(8)
#define MSG_FLAG_CLOCK_ALLOW_FREQ_CHANGE        TI_SCI_MSG_FLAG(9)
#define MSG_FLAG_CLOCK_INPUT_TERM               TI_SCI_MSG_FLAG(10)
        struct ti_sci_msg_hdr hdr;
        u32 dev_id;
        u8 clk_id;
#define MSG_CLOCK_SW_STATE_UNREQ        0
#define MSG_CLOCK_SW_STATE_AUTO         1
#define MSG_CLOCK_SW_STATE_REQ          2
        u8 request_state;
        u32 clk_id_32;
} __packed;

/**
 * struct ti_sci_msg_req_get_clock_state - Request for clock state
 * @hdr:        Generic Header
 * @dev_id:     Device identifier this request is for
 * @clk_id:     Clock identifier for the device for this request.
 *              Each device has it's own set of clock inputs. This indexes
 *              which clock input to get state of. Set to 255 if the clock
 *              ID is greater than or equal to 255.
 * @clk_id_32:  Clock identifier for the device for the request.
 *              Only to be used if the clock ID is greater than or equal to
 *              255.
 *
 * Request type is TI_SCI_MSG_GET_CLOCK_STATE, response is state
 * of the clock
 */
struct ti_sci_msg_req_get_clock_state {
        struct ti_sci_msg_hdr hdr;
        u32 dev_id;
        u8 clk_id;
        u32 clk_id_32;
} __packed;

/**
 * struct ti_sci_msg_resp_get_clock_state - Response to get clock state
 * @hdr:        Generic Header
 * @programmed_state: Any programmed state of the clock. This is one of
 *              MSG_CLOCK_SW_STATE* values.
 * @current_state: Current state of the clock. This is one of:
 *              MSG_CLOCK_HW_STATE_NOT_READY: Clock is not ready
 *              MSG_CLOCK_HW_STATE_READY: Clock is ready
 *
 * Response to TI_SCI_MSG_GET_CLOCK_STATE.
 */
struct ti_sci_msg_resp_get_clock_state {
        struct ti_sci_msg_hdr hdr;
        u8 programmed_state;
#define MSG_CLOCK_HW_STATE_NOT_READY    0
#define MSG_CLOCK_HW_STATE_READY        1
        u8 current_state;
} __packed;

/**
 * struct ti_sci_msg_req_set_clock_parent - Set the clock parent
 * @hdr:        Generic Header
 * @dev_id:     Device identifier this request is for
 * @clk_id:     Clock identifier for the device for this request.
 *              Each device has it's own set of clock inputs. This indexes
 *              which clock input to modify. Set to 255 if clock ID is
 *              greater than or equal to 255.
 * @parent_id:  The new clock parent is selectable by an index via this
 *              parameter. Set to 255 if clock ID is greater than or
 *              equal to 255.
 * @clk_id_32:  Clock identifier if @clk_id field is 255.
 * @parent_id_32:       Parent identifier if @parent_id is 255.
 *
 * Request type is TI_SCI_MSG_SET_CLOCK_PARENT, response is generic
 * ACK / NACK message.
 */
struct ti_sci_msg_req_set_clock_parent {
        struct ti_sci_msg_hdr hdr;
        u32 dev_id;
        u8 clk_id;
        u8 parent_id;
        u32 clk_id_32;
        u32 parent_id_32;
} __packed;

/**
 * struct ti_sci_msg_req_get_clock_parent - Get the clock parent
 * @hdr:        Generic Header
 * @dev_id:     Device identifier this request is for
 * @clk_id:     Clock identifier for the device for this request.
 *              Each device has it's own set of clock inputs. This indexes
 *              which clock input to get the parent for. If this field
 *              contains 255, the actual clock identifier is stored in
 *              @clk_id_32.
 * @clk_id_32:  Clock identifier if the @clk_id field contains 255.
 *
 * Request type is TI_SCI_MSG_GET_CLOCK_PARENT, response is parent information
 */
struct ti_sci_msg_req_get_clock_parent {
        struct ti_sci_msg_hdr hdr;
        u32 dev_id;
        u8 clk_id;
        u32 clk_id_32;
} __packed;

/**
 * struct ti_sci_msg_resp_get_clock_parent - Response with clock parent
 * @hdr:        Generic Header
 * @parent_id:  The current clock parent. If set to 255, the current parent
 *              ID can be found from the @parent_id_32 field.
 * @parent_id_32:       Current clock parent if @parent_id field is set to
 *                      255.
 *
 * Response to TI_SCI_MSG_GET_CLOCK_PARENT.
 */
struct ti_sci_msg_resp_get_clock_parent {
        struct ti_sci_msg_hdr hdr;
        u8 parent_id;
        u32 parent_id_32;
} __packed;

/**
 * struct ti_sci_msg_req_get_clock_num_parents - Request to get clock parents
 * @hdr:        Generic header
 * @dev_id:     Device identifier this request is for
 * @clk_id:     Clock identifier for the device for this request. Set to
 *              255 if clock ID is greater than or equal to 255.
 * @clk_id_32:  Clock identifier if the @clk_id field contains 255.
 *
 * This request provides information about how many clock parent options
 * are available for a given clock to a device. This is typically used
 * for input clocks.
 *
 * Request type is TI_SCI_MSG_GET_NUM_CLOCK_PARENTS, response is appropriate
 * message, or NACK in case of inability to satisfy request.
 */
struct ti_sci_msg_req_get_clock_num_parents {
        struct ti_sci_msg_hdr hdr;
        u32 dev_id;
        u8 clk_id;
        u32 clk_id_32;
} __packed;

/**
 * struct ti_sci_msg_resp_get_clock_num_parents - Response for get clk parents
 * @hdr:                Generic header
 * @num_parents:        Number of clock parents. If set to 255, the actual
 *                      number of parents is stored into @num_parents_32
 *                      field instead.
 * @num_parents_32:     Number of clock parents if @num_parents field is
 *                      set to 255.
 *
 * Response to TI_SCI_MSG_GET_NUM_CLOCK_PARENTS
 */
struct ti_sci_msg_resp_get_clock_num_parents {
        struct ti_sci_msg_hdr hdr;
        u8 num_parents;
        u32 num_parents_32;
} __packed;

/**
 * struct ti_sci_msg_req_query_clock_freq - Request to query a frequency
 * @hdr:        Generic Header
 * @dev_id:     Device identifier this request is for
 * @min_freq_hz: The minimum allowable frequency in Hz. This is the minimum
 *              allowable programmed frequency and does not account for clock
 *              tolerances and jitter.
 * @target_freq_hz: The target clock frequency. A frequency will be found
 *              as close to this target frequency as possible.
 * @max_freq_hz: The maximum allowable frequency in Hz. This is the maximum
 *              allowable programmed frequency and does not account for clock
 *              tolerances and jitter.
 * @clk_id:     Clock identifier for the device for this request. Set to
 *              255 if clock identifier is greater than or equal to 255.
 * @clk_id_32:  Clock identifier if @clk_id is set to 255.
 *
 * NOTE: Normally clock frequency management is automatically done by TISCI
 * entity. In case of specific requests, TISCI evaluates capability to achieve
 * requested frequency within provided range and responds with
 * result message.
 *
 * Request type is TI_SCI_MSG_QUERY_CLOCK_FREQ, response is appropriate message,
 * or NACK in case of inability to satisfy request.
 */
struct ti_sci_msg_req_query_clock_freq {
        struct ti_sci_msg_hdr hdr;
        u32 dev_id;
        u64 min_freq_hz;
        u64 target_freq_hz;
        u64 max_freq_hz;
        u8 clk_id;
        u32 clk_id_32;
} __packed;

/**
 * struct ti_sci_msg_resp_query_clock_freq - Response to a clock frequency query
 * @hdr:        Generic Header
 * @freq_hz:    Frequency that is the best match in Hz.
 *
 * Response to request type TI_SCI_MSG_QUERY_CLOCK_FREQ. NOTE: if the request
 * cannot be satisfied, the message will be of type NACK.
 */
struct ti_sci_msg_resp_query_clock_freq {
        struct ti_sci_msg_hdr hdr;
        u64 freq_hz;
} __packed;

/**
 * struct ti_sci_msg_req_set_clock_freq - Request to setup a clock frequency
 * @hdr:        Generic Header
 * @dev_id:     Device identifier this request is for
 * @min_freq_hz: The minimum allowable frequency in Hz. This is the minimum
 *              allowable programmed frequency and does not account for clock
 *              tolerances and jitter.
 * @target_freq_hz: The target clock frequency. The clock will be programmed
 *              at a rate as close to this target frequency as possible.
 * @max_freq_hz: The maximum allowable frequency in Hz. This is the maximum
 *              allowable programmed frequency and does not account for clock
 *              tolerances and jitter.
 * @clk_id:     Clock identifier for the device for this request. Set to
 *              255 if clock ID is greater than or equal to 255.
 * @clk_id_32:  Clock identifier if @clk_id field is set to 255.
 *
 * NOTE: Normally clock frequency management is automatically done by TISCI
 * entity. In case of specific requests, TISCI evaluates capability to achieve
 * requested range and responds with success/failure message.
 *
 * This sets the desired frequency for a clock within an allowable
 * range. This message will fail on an enabled clock unless
 * MSG_FLAG_CLOCK_ALLOW_FREQ_CHANGE is set for the clock. Additionally,
 * if other clocks have their frequency modified due to this message,
 * they also must have the MSG_FLAG_CLOCK_ALLOW_FREQ_CHANGE or be disabled.
 *
 * Calling set frequency on a clock input to the SoC pseudo-device will
 * inform the PMMC of that clock's frequency. Setting a frequency of
 * zero will indicate the clock is disabled.
 *
 * Calling set frequency on clock outputs from the SoC pseudo-device will
 * function similarly to setting the clock frequency on a device.
 *
 * Request type is TI_SCI_MSG_SET_CLOCK_FREQ, response is a generic ACK/NACK
 * message.
 */
struct ti_sci_msg_req_set_clock_freq {
        struct ti_sci_msg_hdr hdr;
        u32 dev_id;
        u64 min_freq_hz;
        u64 target_freq_hz;
        u64 max_freq_hz;
        u8 clk_id;
        u32 clk_id_32;
} __packed;

/**
 * struct ti_sci_msg_req_get_clock_freq - Request to get the clock frequency
 * @hdr:        Generic Header
 * @dev_id:     Device identifier this request is for
 * @clk_id:     Clock identifier for the device for this request. Set to
 *              255 if clock ID is greater than or equal to 255.
 * @clk_id_32:  Clock identifier if @clk_id field is set to 255.
 *
 * NOTE: Normally clock frequency management is automatically done by TISCI
 * entity. In some cases, clock frequencies are configured by host.
 *
 * Request type is TI_SCI_MSG_GET_CLOCK_FREQ, responded with clock frequency
 * that the clock is currently at.
 */
struct ti_sci_msg_req_get_clock_freq {
        struct ti_sci_msg_hdr hdr;
        u32 dev_id;
        u8 clk_id;
        u32 clk_id_32;
} __packed;

/**
 * struct ti_sci_msg_resp_get_clock_freq - Response of clock frequency request
 * @hdr:        Generic Header
 * @freq_hz:    Frequency that the clock is currently on, in Hz.
 *
 * Response to request type TI_SCI_MSG_GET_CLOCK_FREQ.
 */
struct ti_sci_msg_resp_get_clock_freq {
        struct ti_sci_msg_hdr hdr;
        u64 freq_hz;
} __packed;

#define TI_SCI_IRQ_SECONDARY_HOST_INVALID       0xff

/**
 * struct ti_sci_msg_req_get_resource_range - Request to get a host's assigned
 *                                            range of resources.
 * @hdr:                Generic Header
 * @type:               Unique resource assignment type
 * @subtype:            Resource assignment subtype within the resource type.
 * @secondary_host:     Host processing entity to which the resources are
 *                      allocated. This is required only when the destination
 *                      host id id different from ti sci interface host id,
 *                      else TI_SCI_IRQ_SECONDARY_HOST_INVALID can be passed.
 *
 * Request type is TI_SCI_MSG_GET_RESOURCE_RANGE. Responded with requested
 * resource range which is of type TI_SCI_MSG_GET_RESOURCE_RANGE.
 */
struct ti_sci_msg_req_get_resource_range {
        struct ti_sci_msg_hdr hdr;
#define MSG_RM_RESOURCE_TYPE_MASK       GENMASK(9, 0)
#define MSG_RM_RESOURCE_SUBTYPE_MASK    GENMASK(5, 0)
        u16 type;
        u8 subtype;
        u8 secondary_host;
} __packed;

/**
 * struct ti_sci_msg_resp_get_resource_range - Response to resource get range.
 * @hdr:                Generic Header
 * @range_start:        Start index of the resource range.
 * @range_num:          Number of resources in the range.
 *
 * Response to request TI_SCI_MSG_GET_RESOURCE_RANGE.
 */
struct ti_sci_msg_resp_get_resource_range {
        struct ti_sci_msg_hdr hdr;
        u16 range_start;
        u16 range_num;
} __packed;

/**
 * struct ti_sci_msg_req_manage_irq - Request to configure/release the route
 *                                      between the dev and the host.
 * @hdr:                Generic Header
 * @valid_params:       Bit fields defining the validity of interrupt source
 *                      parameters. If a bit is not set, then corresponding
 *                      field is not valid and will not be used for route set.
 *                      Bit field definitions:
 *                      0 - Valid bit for @dst_id
 *                      1 - Valid bit for @dst_host_irq
 *                      2 - Valid bit for @ia_id
 *                      3 - Valid bit for @vint
 *                      4 - Valid bit for @global_event
 *                      5 - Valid bit for @vint_status_bit_index
 *                      31 - Valid bit for @secondary_host
 * @src_id:             IRQ source peripheral ID.
 * @src_index:          IRQ source index within the peripheral
 * @dst_id:             IRQ Destination ID. Based on the architecture it can be
 *                      IRQ controller or host processor ID.
 * @dst_host_irq:       IRQ number of the destination host IRQ controller
 * @ia_id:              Device ID of the interrupt aggregator in which the
 *                      vint resides.
 * @vint:               Virtual interrupt number if the interrupt route
 *                      is through an interrupt aggregator.
 * @global_event:       Global event that is to be mapped to interrupt
 *                      aggregator virtual interrupt status bit.
 * @vint_status_bit:    Virtual interrupt status bit if the interrupt route
 *                      utilizes an interrupt aggregator status bit.
 * @secondary_host:     Host ID of the IRQ destination computing entity. This is
 *                      required only when destination host id is different
 *                      from ti sci interface host id.
 *
 * Request type is TI_SCI_MSG_SET/RELEASE_IRQ.
 * Response is generic ACK / NACK message.
 */
struct ti_sci_msg_req_manage_irq {
        struct ti_sci_msg_hdr hdr;
#define MSG_FLAG_DST_ID_VALID                   TI_SCI_MSG_FLAG(0)
#define MSG_FLAG_DST_HOST_IRQ_VALID             TI_SCI_MSG_FLAG(1)
#define MSG_FLAG_IA_ID_VALID                    TI_SCI_MSG_FLAG(2)
#define MSG_FLAG_VINT_VALID                     TI_SCI_MSG_FLAG(3)
#define MSG_FLAG_GLB_EVNT_VALID                 TI_SCI_MSG_FLAG(4)
#define MSG_FLAG_VINT_STS_BIT_VALID             TI_SCI_MSG_FLAG(5)
#define MSG_FLAG_SHOST_VALID                    TI_SCI_MSG_FLAG(31)
        u32 valid_params;
        u16 src_id;
        u16 src_index;
        u16 dst_id;
        u16 dst_host_irq;
        u16 ia_id;
        u16 vint;
        u16 global_event;
        u8 vint_status_bit;
        u8 secondary_host;
} __packed;

/**
 * struct ti_sci_msg_rm_ring_cfg_req - Configure a Navigator Subsystem ring
 *
 * Configures the non-real-time registers of a Navigator Subsystem ring.
 * @hdr:        Generic Header
 * @valid_params: Bitfield defining validity of ring configuration parameters.
 *      The ring configuration fields are not valid, and will not be used for
 *      ring configuration, if their corresponding valid bit is zero.
 *      Valid bit usage:
 *      0 - Valid bit for @tisci_msg_rm_ring_cfg_req addr_lo
 *      1 - Valid bit for @tisci_msg_rm_ring_cfg_req addr_hi
 *      2 - Valid bit for @tisci_msg_rm_ring_cfg_req count
 *      3 - Valid bit for @tisci_msg_rm_ring_cfg_req mode
 *      4 - Valid bit for @tisci_msg_rm_ring_cfg_req size
 *      5 - Valid bit for @tisci_msg_rm_ring_cfg_req order_id
 * @nav_id: Device ID of Navigator Subsystem from which the ring is allocated
 * @index: ring index to be configured.
 * @addr_lo: 32 LSBs of ring base address to be programmed into the ring's
 *      RING_BA_LO register
 * @addr_hi: 16 MSBs of ring base address to be programmed into the ring's
 *      RING_BA_HI register.
 * @count: Number of ring elements. Must be even if mode is CREDENTIALS or QM
 *      modes.
 * @mode: Specifies the mode the ring is to be configured.
 * @size: Specifies encoded ring element size. To calculate the encoded size use
 *      the formula (log2(size_bytes) - 2), where size_bytes cannot be
 *      greater than 256.
 * @order_id: Specifies the ring's bus order ID.
 */
struct ti_sci_msg_rm_ring_cfg_req {
        struct ti_sci_msg_hdr hdr;
        u32 valid_params;
        u16 nav_id;
        u16 index;
        u32 addr_lo;
        u32 addr_hi;
        u32 count;
        u8 mode;
        u8 size;
        u8 order_id;
} __packed;

/**
 * struct ti_sci_msg_rm_ring_get_cfg_req - Get RA ring's configuration
 *
 * Gets the configuration of the non-real-time register fields of a ring.  The
 * host, or a supervisor of the host, who owns the ring must be the requesting
 * host.  The values of the non-real-time registers are returned in
 * @ti_sci_msg_rm_ring_get_cfg_resp.
 *
 * @hdr: Generic Header
 * @nav_id: Device ID of Navigator Subsystem from which the ring is allocated
 * @index: ring index.
 */
struct ti_sci_msg_rm_ring_get_cfg_req {
        struct ti_sci_msg_hdr hdr;
        u16 nav_id;
        u16 index;
} __packed;

/**
 * struct ti_sci_msg_rm_ring_get_cfg_resp -  Ring get configuration response
 *
 * Response received by host processor after RM has handled
 * @ti_sci_msg_rm_ring_get_cfg_req. The response contains the ring's
 * non-real-time register values.
 *
 * @hdr: Generic Header
 * @addr_lo: Ring 32 LSBs of base address
 * @addr_hi: Ring 16 MSBs of base address.
 * @count: Ring number of elements.
 * @mode: Ring mode.
 * @size: encoded Ring element size
 * @order_id: ing order ID.
 */
struct ti_sci_msg_rm_ring_get_cfg_resp {
        struct ti_sci_msg_hdr hdr;
        u32 addr_lo;
        u32 addr_hi;
        u32 count;
        u8 mode;
        u8 size;
        u8 order_id;
} __packed;

/**
 * struct ti_sci_msg_psil_pair - Pairs a PSI-L source thread to a destination
 *                               thread
 * @hdr:        Generic Header
 * @nav_id:     SoC Navigator Subsystem device ID whose PSI-L config proxy is
 *              used to pair the source and destination threads.
 * @src_thread: PSI-L source thread ID within the PSI-L System thread map.
 *
 * UDMAP transmit channels mapped to source threads will have their
 * TCHAN_THRD_ID register programmed with the destination thread if the pairing
 * is successful.

 * @dst_thread: PSI-L destination thread ID within the PSI-L System thread map.
 * PSI-L destination threads start at index 0x8000.  The request is NACK'd if
 * the destination thread is not greater than or equal to 0x8000.
 *
 * UDMAP receive channels mapped to destination threads will have their
 * RCHAN_THRD_ID register programmed with the source thread if the pairing
 * is successful.
 *
 * Request type is TI_SCI_MSG_RM_PSIL_PAIR, response is a generic ACK or NACK
 * message.
 */
struct ti_sci_msg_psil_pair {
        struct ti_sci_msg_hdr hdr;
        u32 nav_id;
        u32 src_thread;
        u32 dst_thread;
} __packed;

/**
 * struct ti_sci_msg_psil_unpair - Unpairs a PSI-L source thread from a
 *                                 destination thread
 * @hdr:        Generic Header
 * @nav_id:     SoC Navigator Subsystem device ID whose PSI-L config proxy is
 *              used to unpair the source and destination threads.
 * @src_thread: PSI-L source thread ID within the PSI-L System thread map.
 *
 * UDMAP transmit channels mapped to source threads will have their
 * TCHAN_THRD_ID register cleared if the unpairing is successful.
 *
 * @dst_thread: PSI-L destination thread ID within the PSI-L System thread map.
 * PSI-L destination threads start at index 0x8000.  The request is NACK'd if
 * the destination thread is not greater than or equal to 0x8000.
 *
 * UDMAP receive channels mapped to destination threads will have their
 * RCHAN_THRD_ID register cleared if the unpairing is successful.
 *
 * Request type is TI_SCI_MSG_RM_PSIL_UNPAIR, response is a generic ACK or NACK
 * message.
 */
struct ti_sci_msg_psil_unpair {
        struct ti_sci_msg_hdr hdr;
        u32 nav_id;
        u32 src_thread;
        u32 dst_thread;
} __packed;

/**
 * struct ti_sci_msg_udmap_rx_flow_cfg -  UDMAP receive flow configuration
 *                                        message
 * @hdr: Generic Header
 * @nav_id: SoC Navigator Subsystem device ID from which the receive flow is
 *      allocated
 * @flow_index: UDMAP receive flow index for non-optional configuration.
 * @rx_ch_index: Specifies the index of the receive channel using the flow_index
 * @rx_einfo_present: UDMAP receive flow extended packet info present.
 * @rx_psinfo_present: UDMAP receive flow PS words present.
 * @rx_error_handling: UDMAP receive flow error handling configuration. Valid
 *      values are TI_SCI_RM_UDMAP_RX_FLOW_ERR_DROP/RETRY.
 * @rx_desc_type: UDMAP receive flow descriptor type. It can be one of
 *      TI_SCI_RM_UDMAP_RX_FLOW_DESC_HOST/MONO.
 * @rx_sop_offset: UDMAP receive flow start of packet offset.
 * @rx_dest_qnum: UDMAP receive flow destination queue number.
 * @rx_ps_location: UDMAP receive flow PS words location.
 *      0 - end of packet descriptor
 *      1 - Beginning of the data buffer
 * @rx_src_tag_hi: UDMAP receive flow source tag high byte constant
 * @rx_src_tag_lo: UDMAP receive flow source tag low byte constant
 * @rx_dest_tag_hi: UDMAP receive flow destination tag high byte constant
 * @rx_dest_tag_lo: UDMAP receive flow destination tag low byte constant
 * @rx_src_tag_hi_sel: UDMAP receive flow source tag high byte selector
 * @rx_src_tag_lo_sel: UDMAP receive flow source tag low byte selector
 * @rx_dest_tag_hi_sel: UDMAP receive flow destination tag high byte selector
 * @rx_dest_tag_lo_sel: UDMAP receive flow destination tag low byte selector
 * @rx_size_thresh_en: UDMAP receive flow packet size based free buffer queue
 *      enable. If enabled, the ti_sci_rm_udmap_rx_flow_opt_cfg also need to be
 *      configured and sent.
 * @rx_fdq0_sz0_qnum: UDMAP receive flow free descriptor queue 0.
 * @rx_fdq1_qnum: UDMAP receive flow free descriptor queue 1.
 * @rx_fdq2_qnum: UDMAP receive flow free descriptor queue 2.
 * @rx_fdq3_qnum: UDMAP receive flow free descriptor queue 3.
 *
 * For detailed information on the settings, see the UDMAP section of the TRM.
 */
struct ti_sci_msg_udmap_rx_flow_cfg {
        struct ti_sci_msg_hdr hdr;
        u32 nav_id;
        u32 flow_index;
        u32 rx_ch_index;
        u8 rx_einfo_present;
        u8 rx_psinfo_present;
        u8 rx_error_handling;
        u8 rx_desc_type;
        u16 rx_sop_offset;
        u16 rx_dest_qnum;
        u8 rx_ps_location;
        u8 rx_src_tag_hi;
        u8 rx_src_tag_lo;
        u8 rx_dest_tag_hi;
        u8 rx_dest_tag_lo;
        u8 rx_src_tag_hi_sel;
        u8 rx_src_tag_lo_sel;
        u8 rx_dest_tag_hi_sel;
        u8 rx_dest_tag_lo_sel;
        u8 rx_size_thresh_en;
        u16 rx_fdq0_sz0_qnum;
        u16 rx_fdq1_qnum;
        u16 rx_fdq2_qnum;
        u16 rx_fdq3_qnum;
} __packed;

/**
 * struct rm_ti_sci_msg_udmap_rx_flow_opt_cfg - parameters for UDMAP receive
 *                                              flow optional configuration
 * @hdr: Generic Header
 * @nav_id: SoC Navigator Subsystem device ID from which the receive flow is
 *      allocated
 * @flow_index: UDMAP receive flow index for optional configuration.
 * @rx_ch_index: Specifies the index of the receive channel using the flow_index
 * @rx_size_thresh0: UDMAP receive flow packet size threshold 0.
 * @rx_size_thresh1: UDMAP receive flow packet size threshold 1.
 * @rx_size_thresh2: UDMAP receive flow packet size threshold 2.
 * @rx_fdq0_sz1_qnum: UDMAP receive flow free descriptor queue for size
 *      threshold 1.
 * @rx_fdq0_sz2_qnum: UDMAP receive flow free descriptor queue for size
 *      threshold 2.
 * @rx_fdq0_sz3_qnum: UDMAP receive flow free descriptor queue for size
 *      threshold 3.
 *
 * For detailed information on the settings, see the UDMAP section of the TRM.
 */
struct rm_ti_sci_msg_udmap_rx_flow_opt_cfg {
        struct ti_sci_msg_hdr hdr;
        u32 nav_id;
        u32 flow_index;
        u32 rx_ch_index;
        u16 rx_size_thresh0;
        u16 rx_size_thresh1;
        u16 rx_size_thresh2;
        u16 rx_fdq0_sz1_qnum;
        u16 rx_fdq0_sz2_qnum;
        u16 rx_fdq0_sz3_qnum;
} __packed;

/**
 * Configures a Navigator Subsystem UDMAP transmit channel
 *
 * Configures the non-real-time registers of a Navigator Subsystem UDMAP
 * transmit channel.  The channel index must be assigned to the host defined
 * in the TISCI header via the RM board configuration resource assignment
 * range list.
 *
 * @hdr: Generic Header
 *
 * @valid_params: Bitfield defining validity of tx channel configuration
 * parameters. The tx channel configuration fields are not valid, and will not
 * be used for ch configuration, if their corresponding valid bit is zero.
 * Valid bit usage:
 *    0 - Valid bit for @ref ti_sci_msg_rm_udmap_tx_ch_cfg::tx_pause_on_err
 *    1 - Valid bit for @ref ti_sci_msg_rm_udmap_tx_ch_cfg::tx_atype
 *    2 - Valid bit for @ref ti_sci_msg_rm_udmap_tx_ch_cfg::tx_chan_type
 *    3 - Valid bit for @ref ti_sci_msg_rm_udmap_tx_ch_cfg::tx_fetch_size
 *    4 - Valid bit for @ref ti_sci_msg_rm_udmap_tx_ch_cfg::txcq_qnum
 *    5 - Valid bit for @ref ti_sci_msg_rm_udmap_tx_ch_cfg::tx_priority
 *    6 - Valid bit for @ref ti_sci_msg_rm_udmap_tx_ch_cfg::tx_qos
 *    7 - Valid bit for @ref ti_sci_msg_rm_udmap_tx_ch_cfg::tx_orderid
 *    8 - Valid bit for @ref ti_sci_msg_rm_udmap_tx_ch_cfg::tx_sched_priority
 *    9 - Valid bit for @ref ti_sci_msg_rm_udmap_tx_ch_cfg::tx_filt_einfo
 *   10 - Valid bit for @ref ti_sci_msg_rm_udmap_tx_ch_cfg::tx_filt_pswords
 *   11 - Valid bit for @ref ti_sci_msg_rm_udmap_tx_ch_cfg::tx_supr_tdpkt
 *   12 - Valid bit for @ref ti_sci_msg_rm_udmap_tx_ch_cfg::tx_credit_count
 *   13 - Valid bit for @ref ti_sci_msg_rm_udmap_tx_ch_cfg::fdepth
 *   14 - Valid bit for @ref ti_sci_msg_rm_udmap_tx_ch_cfg::tx_burst_size
 *
 * @nav_id: SoC device ID of Navigator Subsystem where tx channel is located
 *
 * @index: UDMAP transmit channel index.
 *
 * @tx_pause_on_err: UDMAP transmit channel pause on error configuration to
 * be programmed into the tx_pause_on_err field of the channel's TCHAN_TCFG
 * register.
 *
 * @tx_filt_einfo: UDMAP transmit channel extended packet information passing
 * configuration to be programmed into the tx_filt_einfo field of the
 * channel's TCHAN_TCFG register.
 *
 * @tx_filt_pswords: UDMAP transmit channel protocol specific word passing
 * configuration to be programmed into the tx_filt_pswords field of the
 * channel's TCHAN_TCFG register.
 *
 * @tx_atype: UDMAP transmit channel non Ring Accelerator access pointer
 * interpretation configuration to be programmed into the tx_atype field of
 * the channel's TCHAN_TCFG register.
 *
 * @tx_chan_type: UDMAP transmit channel functional channel type and work
 * passing mechanism configuration to be programmed into the tx_chan_type
 * field of the channel's TCHAN_TCFG register.
 *
 * @tx_supr_tdpkt: UDMAP transmit channel teardown packet generation suppression
 * configuration to be programmed into the tx_supr_tdpkt field of the channel's
 * TCHAN_TCFG register.
 *
 * @tx_fetch_size: UDMAP transmit channel number of 32-bit descriptor words to
 * fetch configuration to be programmed into the tx_fetch_size field of the
 * channel's TCHAN_TCFG register.  The user must make sure to set the maximum
 * word count that can pass through the channel for any allowed descriptor type.
 *
 * @tx_credit_count: UDMAP transmit channel transfer request credit count
 * configuration to be programmed into the count field of the TCHAN_TCREDIT
 * register.  Specifies how many credits for complete TRs are available.
 *
 * @txcq_qnum: UDMAP transmit channel completion queue configuration to be
 * programmed into the txcq_qnum field of the TCHAN_TCQ register. The specified
 * completion queue must be assigned to the host, or a subordinate of the host,
 * requesting configuration of the transmit channel.
 *
 * @tx_priority: UDMAP transmit channel transmit priority value to be programmed
 * into the priority field of the channel's TCHAN_TPRI_CTRL register.
 *
 * @tx_qos: UDMAP transmit channel transmit qos value to be programmed into the
 * qos field of the channel's TCHAN_TPRI_CTRL register.
 *
 * @tx_orderid: UDMAP transmit channel bus order id value to be programmed into
 * the orderid field of the channel's TCHAN_TPRI_CTRL register.
 *
 * @fdepth: UDMAP transmit channel FIFO depth configuration to be programmed
 * into the fdepth field of the TCHAN_TFIFO_DEPTH register. Sets the number of
 * Tx FIFO bytes which are allowed to be stored for the channel. Check the UDMAP
 * section of the TRM for restrictions regarding this parameter.
 *
 * @tx_sched_priority: UDMAP transmit channel tx scheduling priority
 * configuration to be programmed into the priority field of the channel's
 * TCHAN_TST_SCHED register.
 *
 * @tx_burst_size: UDMAP transmit channel burst size configuration to be
 * programmed into the tx_burst_size field of the TCHAN_TCFG register.
 */
struct ti_sci_msg_rm_udmap_tx_ch_cfg_req {
        struct ti_sci_msg_hdr hdr;
        u32 valid_params;
        u16 nav_id;
        u16 index;
        u8 tx_pause_on_err;
        u8 tx_filt_einfo;
        u8 tx_filt_pswords;
        u8 tx_atype;
        u8 tx_chan_type;
        u8 tx_supr_tdpkt;
        u16 tx_fetch_size;
        u8 tx_credit_count;
        u16 txcq_qnum;
        u8 tx_priority;
        u8 tx_qos;
        u8 tx_orderid;
        u16 fdepth;
        u8 tx_sched_priority;
        u8 tx_burst_size;
} __packed;

/**
 * Configures a Navigator Subsystem UDMAP receive channel
 *
 * Configures the non-real-time registers of a Navigator Subsystem UDMAP
 * receive channel.  The channel index must be assigned to the host defined
 * in the TISCI header via the RM board configuration resource assignment
 * range list.
 *
 * @hdr: Generic Header
 *
 * @valid_params: Bitfield defining validity of rx channel configuration
 * parameters.
 * The rx channel configuration fields are not valid, and will not be used for
 * ch configuration, if their corresponding valid bit is zero.
 * Valid bit usage:
 *    0 - Valid bit for @ti_sci_msg_rm_udmap_rx_ch_cfg_req::rx_pause_on_err
 *    1 - Valid bit for @ti_sci_msg_rm_udmap_rx_ch_cfg_req::rx_atype
 *    2 - Valid bit for @ti_sci_msg_rm_udmap_rx_ch_cfg_req::rx_chan_type
 *    3 - Valid bit for @ti_sci_msg_rm_udmap_rx_ch_cfg_req::rx_fetch_size
 *    4 - Valid bit for @ti_sci_msg_rm_udmap_rx_ch_cfg_req::rxcq_qnum
 *    5 - Valid bit for @ti_sci_msg_rm_udmap_rx_ch_cfg_req::rx_priority
 *    6 - Valid bit for @ti_sci_msg_rm_udmap_rx_ch_cfg_req::rx_qos
 *    7 - Valid bit for @ti_sci_msg_rm_udmap_rx_ch_cfg_req::rx_orderid
 *    8 - Valid bit for @ti_sci_msg_rm_udmap_rx_ch_cfg_req::rx_sched_priority
 *    9 - Valid bit for @ti_sci_msg_rm_udmap_rx_ch_cfg_req::flowid_start
 *   10 - Valid bit for @ti_sci_msg_rm_udmap_rx_ch_cfg_req::flowid_cnt
 *   11 - Valid bit for @ti_sci_msg_rm_udmap_rx_ch_cfg_req::rx_ignore_short
 *   12 - Valid bit for @ti_sci_msg_rm_udmap_rx_ch_cfg_req::rx_ignore_long
 *   14 - Valid bit for @ti_sci_msg_rm_udmap_rx_ch_cfg_req::rx_burst_size
 *
 * @nav_id: SoC device ID of Navigator Subsystem where rx channel is located
 *
 * @index: UDMAP receive channel index.
 *
 * @rx_fetch_size: UDMAP receive channel number of 32-bit descriptor words to
 * fetch configuration to be programmed into the rx_fetch_size field of the
 * channel's RCHAN_RCFG register.
 *
 * @rxcq_qnum: UDMAP receive channel completion queue configuration to be
 * programmed into the rxcq_qnum field of the RCHAN_RCQ register.
 * The specified completion queue must be assigned to the host, or a subordinate
 * of the host, requesting configuration of the receive channel.
 *
 * @rx_priority: UDMAP receive channel receive priority value to be programmed
 * into the priority field of the channel's RCHAN_RPRI_CTRL register.
 *
 * @rx_qos: UDMAP receive channel receive qos value to be programmed into the
 * qos field of the channel's RCHAN_RPRI_CTRL register.
 *
 * @rx_orderid: UDMAP receive channel bus order id value to be programmed into
 * the orderid field of the channel's RCHAN_RPRI_CTRL register.
 *
 * @rx_sched_priority: UDMAP receive channel rx scheduling priority
 * configuration to be programmed into the priority field of the channel's
 * RCHAN_RST_SCHED register.
 *
 * @flowid_start: UDMAP receive channel additional flows starting index
 * configuration to program into the flow_start field of the RCHAN_RFLOW_RNG
 * register. Specifies the starting index for flow IDs the receive channel is to
 * make use of beyond the default flow. flowid_start and @ref flowid_cnt must be
 * set as valid and configured together. The starting flow ID set by
 * @ref flowid_cnt must be a flow index within the Navigator Subsystem's subset
 * of flows beyond the default flows statically mapped to receive channels.
 * The additional flows must be assigned to the host, or a subordinate of the
 * host, requesting configuration of the receive channel.
 *
 * @flowid_cnt: UDMAP receive channel additional flows count configuration to
 * program into the flowid_cnt field of the RCHAN_RFLOW_RNG register.
 * This field specifies how many flow IDs are in the additional contiguous range
 * of legal flow IDs for the channel.  @ref flowid_start and flowid_cnt must be
 * set as valid and configured together. Disabling the valid_params field bit
 * for flowid_cnt indicates no flow IDs other than the default are to be
 * allocated and used by the receive channel. @ref flowid_start plus flowid_cnt
 * cannot be greater than the number of receive flows in the receive channel's
 * Navigator Subsystem.  The additional flows must be assigned to the host, or a
 * subordinate of the host, requesting configuration of the receive channel.
 *
 * @rx_pause_on_err: UDMAP receive channel pause on error configuration to be
 * programmed into the rx_pause_on_err field of the channel's RCHAN_RCFG
 * register.
 *
 * @rx_atype: UDMAP receive channel non Ring Accelerator access pointer
 * interpretation configuration to be programmed into the rx_atype field of the
 * channel's RCHAN_RCFG register.
 *
 * @rx_chan_type: UDMAP receive channel functional channel type and work passing
 * mechanism configuration to be programmed into the rx_chan_type field of the
 * channel's RCHAN_RCFG register.
 *
 * @rx_ignore_short: UDMAP receive channel short packet treatment configuration
 * to be programmed into the rx_ignore_short field of the RCHAN_RCFG register.
 *
 * @rx_ignore_long: UDMAP receive channel long packet treatment configuration to
 * be programmed into the rx_ignore_long field of the RCHAN_RCFG register.
 *
 * @rx_burst_size: UDMAP receive channel burst size configuration to be
 * programmed into the rx_burst_size field of the RCHAN_RCFG register.
 */
struct ti_sci_msg_rm_udmap_rx_ch_cfg_req {
        struct ti_sci_msg_hdr hdr;
        u32 valid_params;
        u16 nav_id;
        u16 index;
        u16 rx_fetch_size;
        u16 rxcq_qnum;
        u8 rx_priority;
        u8 rx_qos;
        u8 rx_orderid;
        u8 rx_sched_priority;
        u16 flowid_start;
        u16 flowid_cnt;
        u8 rx_pause_on_err;
        u8 rx_atype;
        u8 rx_chan_type;
        u8 rx_ignore_short;
        u8 rx_ignore_long;
        u8 rx_burst_size;
} __packed;

/**
 * Configures a Navigator Subsystem UDMAP receive flow
 *
 * Configures a Navigator Subsystem UDMAP receive flow's registers.
 * Configuration does not include the flow registers which handle size-based
 * free descriptor queue routing.
 *
 * The flow index must be assigned to the host defined in the TISCI header via
 * the RM board configuration resource assignment range list.
 *
 * @hdr: Standard TISCI header
 *
 * @valid_params
 * Bitfield defining validity of rx flow configuration parameters.  The
 * rx flow configuration fields are not valid, and will not be used for flow
 * configuration, if their corresponding valid bit is zero.  Valid bit usage:
 *     0 - Valid bit for @tisci_msg_rm_udmap_flow_cfg_req::rx_einfo_present
 *     1 - Valid bit for @tisci_msg_rm_udmap_flow_cfg_req::rx_psinfo_present
 *     2 - Valid bit for @tisci_msg_rm_udmap_flow_cfg_req::rx_error_handling
 *     3 - Valid bit for @tisci_msg_rm_udmap_flow_cfg_req::rx_desc_type
 *     4 - Valid bit for @tisci_msg_rm_udmap_flow_cfg_req::rx_sop_offset
 *     5 - Valid bit for @tisci_msg_rm_udmap_flow_cfg_req::rx_dest_qnum
 *     6 - Valid bit for @tisci_msg_rm_udmap_flow_cfg_req::rx_src_tag_hi
 *     7 - Valid bit for @tisci_msg_rm_udmap_flow_cfg_req::rx_src_tag_lo
 *     8 - Valid bit for @tisci_msg_rm_udmap_flow_cfg_req::rx_dest_tag_hi
 *     9 - Valid bit for @tisci_msg_rm_udmap_flow_cfg_req::rx_dest_tag_lo
 *    10 - Valid bit for @tisci_msg_rm_udmap_flow_cfg_req::rx_src_tag_hi_sel
 *    11 - Valid bit for @tisci_msg_rm_udmap_flow_cfg_req::rx_src_tag_lo_sel
 *    12 - Valid bit for @tisci_msg_rm_udmap_flow_cfg_req::rx_dest_tag_hi_sel
 *    13 - Valid bit for @tisci_msg_rm_udmap_flow_cfg_req::rx_dest_tag_lo_sel
 *    14 - Valid bit for @tisci_msg_rm_udmap_flow_cfg_req::rx_fdq0_sz0_qnum
 *    15 - Valid bit for @tisci_msg_rm_udmap_flow_cfg_req::rx_fdq1_sz0_qnum
 *    16 - Valid bit for @tisci_msg_rm_udmap_flow_cfg_req::rx_fdq2_sz0_qnum
 *    17 - Valid bit for @tisci_msg_rm_udmap_flow_cfg_req::rx_fdq3_sz0_qnum
 *    18 - Valid bit for @tisci_msg_rm_udmap_flow_cfg_req::rx_ps_location
 *
 * @nav_id: SoC device ID of Navigator Subsystem from which the receive flow is
 * allocated
 *
 * @flow_index: UDMAP receive flow index for non-optional configuration.
 *
 * @rx_einfo_present:
 * UDMAP receive flow extended packet info present configuration to be
 * programmed into the rx_einfo_present field of the flow's RFLOW_RFA register.
 *
 * @rx_psinfo_present:
 * UDMAP receive flow PS words present configuration to be programmed into the
 * rx_psinfo_present field of the flow's RFLOW_RFA register.
 *
 * @rx_error_handling:
 * UDMAP receive flow error handling configuration to be programmed into the
 * rx_error_handling field of the flow's RFLOW_RFA register.
 *
 * @rx_desc_type:
 * UDMAP receive flow descriptor type configuration to be programmed into the
 * rx_desc_type field field of the flow's RFLOW_RFA register.
 *
 * @rx_sop_offset:
 * UDMAP receive flow start of packet offset configuration to be programmed
 * into the rx_sop_offset field of the RFLOW_RFA register.  See the UDMAP
 * section of the TRM for more information on this setting.  Valid values for
 * this field are 0-255 bytes.
 *
 * @rx_dest_qnum:
 * UDMAP receive flow destination queue configuration to be programmed into the
 * rx_dest_qnum field of the flow's RFLOW_RFA register.  The specified
 * destination queue must be valid within the Navigator Subsystem and must be
 * owned by the host, or a subordinate of the host, requesting allocation and
 * configuration of the receive flow.
 *
 * @rx_src_tag_hi:
 * UDMAP receive flow source tag high byte constant configuration to be
 * programmed into the rx_src_tag_hi field of the flow's RFLOW_RFB register.
 * See the UDMAP section of the TRM for more information on this setting.
 *
 * @rx_src_tag_lo:
 * UDMAP receive flow source tag low byte constant configuration to be
 * programmed into the rx_src_tag_lo field of the flow's RFLOW_RFB register.
 * See the UDMAP section of the TRM for more information on this setting.
 *
 * @rx_dest_tag_hi:
 * UDMAP receive flow destination tag high byte constant configuration to be
 * programmed into the rx_dest_tag_hi field of the flow's RFLOW_RFB register.
 * See the UDMAP section of the TRM for more information on this setting.
 *
 * @rx_dest_tag_lo:
 * UDMAP receive flow destination tag low byte constant configuration to be
 * programmed into the rx_dest_tag_lo field of the flow's RFLOW_RFB register.
 * See the UDMAP section of the TRM for more information on this setting.
 *
 * @rx_src_tag_hi_sel:
 * UDMAP receive flow source tag high byte selector configuration to be
 * programmed into the rx_src_tag_hi_sel field of the RFLOW_RFC register.  See
 * the UDMAP section of the TRM for more information on this setting.
 *
 * @rx_src_tag_lo_sel:
 * UDMAP receive flow source tag low byte selector configuration to be
 * programmed into the rx_src_tag_lo_sel field of the RFLOW_RFC register.  See
 * the UDMAP section of the TRM for more information on this setting.
 *
 * @rx_dest_tag_hi_sel:
 * UDMAP receive flow destination tag high byte selector configuration to be
 * programmed into the rx_dest_tag_hi_sel field of the RFLOW_RFC register.  See
 * the UDMAP section of the TRM for more information on this setting.
 *
 * @rx_dest_tag_lo_sel:
 * UDMAP receive flow destination tag low byte selector configuration to be
 * programmed into the rx_dest_tag_lo_sel field of the RFLOW_RFC register.  See
 * the UDMAP section of the TRM for more information on this setting.
 *
 * @rx_fdq0_sz0_qnum:
 * UDMAP receive flow free descriptor queue 0 configuration to be programmed
 * into the rx_fdq0_sz0_qnum field of the flow's RFLOW_RFD register.  See the
 * UDMAP section of the TRM for more information on this setting. The specified
 * free queue must be valid within the Navigator Subsystem and must be owned
 * by the host, or a subordinate of the host, requesting allocation and
 * configuration of the receive flow.
 *
 * @rx_fdq1_qnum:
 * UDMAP receive flow free descriptor queue 1 configuration to be programmed
 * into the rx_fdq1_qnum field of the flow's RFLOW_RFD register.  See the
 * UDMAP section of the TRM for more information on this setting.  The specified
 * free queue must be valid within the Navigator Subsystem and must be owned
 * by the host, or a subordinate of the host, requesting allocation and
 * configuration of the receive flow.
 *
 * @rx_fdq2_qnum:
 * UDMAP receive flow free descriptor queue 2 configuration to be programmed
 * into the rx_fdq2_qnum field of the flow's RFLOW_RFE register.  See the
 * UDMAP section of the TRM for more information on this setting.  The specified
 * free queue must be valid within the Navigator Subsystem and must be owned
 * by the host, or a subordinate of the host, requesting allocation and
 * configuration of the receive flow.
 *
 * @rx_fdq3_qnum:
 * UDMAP receive flow free descriptor queue 3 configuration to be programmed
 * into the rx_fdq3_qnum field of the flow's RFLOW_RFE register.  See the
 * UDMAP section of the TRM for more information on this setting.  The specified
 * free queue must be valid within the Navigator Subsystem and must be owned
 * by the host, or a subordinate of the host, requesting allocation and
 * configuration of the receive flow.
 *
 * @rx_ps_location:
 * UDMAP receive flow PS words location configuration to be programmed into the
 * rx_ps_location field of the flow's RFLOW_RFA register.
 */
struct ti_sci_msg_rm_udmap_flow_cfg_req {
        struct ti_sci_msg_hdr hdr;
        u32 valid_params;
        u16 nav_id;
        u16 flow_index;
        u8 rx_einfo_present;
        u8 rx_psinfo_present;
        u8 rx_error_handling;
        u8 rx_desc_type;
        u16 rx_sop_offset;
        u16 rx_dest_qnum;
        u8 rx_src_tag_hi;
        u8 rx_src_tag_lo;
        u8 rx_dest_tag_hi;
        u8 rx_dest_tag_lo;
        u8 rx_src_tag_hi_sel;
        u8 rx_src_tag_lo_sel;
        u8 rx_dest_tag_hi_sel;
        u8 rx_dest_tag_lo_sel;
        u16 rx_fdq0_sz0_qnum;
        u16 rx_fdq1_qnum;
        u16 rx_fdq2_qnum;
        u16 rx_fdq3_qnum;
        u8 rx_ps_location;
} __packed;

/**
 * struct ti_sci_msg_req_proc_request - Request a processor
 * @hdr:                Generic Header
 * @processor_id:       ID of processor being requested
 *
 * Request type is TI_SCI_MSG_PROC_REQUEST, response is a generic ACK/NACK
 * message.
 */
struct ti_sci_msg_req_proc_request {
        struct ti_sci_msg_hdr hdr;
        u8 processor_id;
} __packed;

/**
 * struct ti_sci_msg_req_proc_release - Release a processor
 * @hdr:                Generic Header
 * @processor_id:       ID of processor being released
 *
 * Request type is TI_SCI_MSG_PROC_RELEASE, response is a generic ACK/NACK
 * message.
 */
struct ti_sci_msg_req_proc_release {
        struct ti_sci_msg_hdr hdr;
        u8 processor_id;
} __packed;

/**
 * struct ti_sci_msg_req_proc_handover - Handover a processor to a host
 * @hdr:                Generic Header
 * @processor_id:       ID of processor being handed over
 * @host_id:            Host ID the control needs to be transferred to
 *
 * Request type is TI_SCI_MSG_PROC_HANDOVER, response is a generic ACK/NACK
 * message.
 */
struct ti_sci_msg_req_proc_handover {
        struct ti_sci_msg_hdr hdr;
        u8 processor_id;
        u8 host_id;
} __packed;

/* Boot Vector masks */
#define TI_SCI_ADDR_LOW_MASK                    GENMASK_ULL(31, 0)
#define TI_SCI_ADDR_HIGH_MASK                   GENMASK_ULL(63, 32)
#define TI_SCI_ADDR_HIGH_SHIFT                  32

/**
 * struct ti_sci_msg_req_set_config - Set Processor boot configuration
 * @hdr:                Generic Header
 * @processor_id:       ID of processor being configured
 * @bootvector_low:     Lower 32 bit address (Little Endian) of boot vector
 * @bootvector_high:    Higher 32 bit address (Little Endian) of boot vector
 * @config_flags_set:   Optional Processor specific Config Flags to set.
 *                      Setting a bit here implies the corresponding mode
 *                      will be set
 * @config_flags_clear: Optional Processor specific Config Flags to clear.
 *                      Setting a bit here implies the corresponding mode
 *                      will be cleared
 *
 * Request type is TI_SCI_MSG_PROC_HANDOVER, response is a generic ACK/NACK
 * message.
 */
struct ti_sci_msg_req_set_config {
        struct ti_sci_msg_hdr hdr;
        u8 processor_id;
        u32 bootvector_low;
        u32 bootvector_high;
        u32 config_flags_set;
        u32 config_flags_clear;
} __packed;

/**
 * struct ti_sci_msg_req_set_ctrl - Set Processor boot control flags
 * @hdr:                Generic Header
 * @processor_id:       ID of processor being configured
 * @control_flags_set:  Optional Processor specific Control Flags to set.
 *                      Setting a bit here implies the corresponding mode
 *                      will be set
 * @control_flags_clear:Optional Processor specific Control Flags to clear.
 *                      Setting a bit here implies the corresponding mode
 *                      will be cleared
 *
 * Request type is TI_SCI_MSG_SET_CTRL, response is a generic ACK/NACK
 * message.
 */
struct ti_sci_msg_req_set_ctrl {
        struct ti_sci_msg_hdr hdr;
        u8 processor_id;
        u32 control_flags_set;
        u32 control_flags_clear;
} __packed;

/**
 * struct ti_sci_msg_req_get_status - Processor boot status request
 * @hdr:                Generic Header
 * @processor_id:       ID of processor whose status is being requested
 *
 * Request type is TI_SCI_MSG_GET_STATUS, response is an appropriate
 * message, or NACK in case of inability to satisfy request.
 */
struct ti_sci_msg_req_get_status {
        struct ti_sci_msg_hdr hdr;
        u8 processor_id;
} __packed;

/**
 * struct ti_sci_msg_resp_get_status - Processor boot status response
 * @hdr:                Generic Header
 * @processor_id:       ID of processor whose status is returned
 * @bootvector_low:     Lower 32 bit address (Little Endian) of boot vector
 * @bootvector_high:    Higher 32 bit address (Little Endian) of boot vector
 * @config_flags:       Optional Processor specific Config Flags set currently
 * @control_flags:      Optional Processor specific Control Flags set currently
 * @status_flags:       Optional Processor specific Status Flags set currently
 *
 * Response structure to a TI_SCI_MSG_GET_STATUS request.
 */
struct ti_sci_msg_resp_get_status {
        struct ti_sci_msg_hdr hdr;
        u8 processor_id;
        u32 bootvector_low;
        u32 bootvector_high;
        u32 config_flags;
        u32 control_flags;
        u32 status_flags;
} __packed;

#endif /* __TI_SCI_H */