?  search:
summary | log | graphiclog1 | graphiclog2 | commit | commitdiff | tree | refs | edit | fork
blame | history | raw | HEAD
treewide: remove redundant IS_ERR() before error code check
[linux/fpc-iii.git] / drivers / i2c / busses / i2c-omap.c
blob2dfea357b13132d61d361b1694f84e0c5dafa9bb
1 // SPDX-License-Identifier: GPL-2.0-or-later
2 /*
3 * TI OMAP I2C master mode driver
4 *
5 * Copyright (C) 2003 MontaVista Software, Inc.
6 * Copyright (C) 2005 Nokia Corporation
7 * Copyright (C) 2004 - 2007 Texas Instruments.
8 *
9 * Originally written by MontaVista Software, Inc.
10 * Additional contributions by:
11 * Tony Lindgren <tony@atomide.com>
12 * Imre Deak <imre.deak@nokia.com>
13 * Juha Yrjölä <juha.yrjola@solidboot.com>
14 * Syed Khasim <x0khasim@ti.com>
15 * Nishant Menon <nm@ti.com>
16 */
17
18 #include <linux/module.h>
19 #include <linux/delay.h>
20 #include <linux/i2c.h>
21 #include <linux/err.h>
22 #include <linux/interrupt.h>
23 #include <linux/completion.h>
24 #include <linux/platform_device.h>
25 #include <linux/clk.h>
26 #include <linux/io.h>
27 #include <linux/of.h>
28 #include <linux/of_device.h>
29 #include <linux/slab.h>
30 #include <linux/platform_data/i2c-omap.h>
31 #include <linux/pm_runtime.h>
32 #include <linux/pinctrl/consumer.h>
33
34 /* I2C controller revisions */
35 #define OMAP_I2C_OMAP1_REV_2 0x20
36
37 /* I2C controller revisions present on specific hardware */
38 #define OMAP_I2C_REV_ON_2430 0x00000036
39 #define OMAP_I2C_REV_ON_3430_3530 0x0000003C
40 #define OMAP_I2C_REV_ON_3630 0x00000040
41 #define OMAP_I2C_REV_ON_4430_PLUS 0x50400002
42
43 /* timeout waiting for the controller to respond */
44 #define OMAP_I2C_TIMEOUT (msecs_to_jiffies(1000))
45
46 /* timeout for pm runtime autosuspend */
47 #define OMAP_I2C_PM_TIMEOUT 1000 /* ms */
48
49 /* timeout for making decision on bus free status */
50 #define OMAP_I2C_BUS_FREE_TIMEOUT (msecs_to_jiffies(10))
51
52 /* For OMAP3 I2C_IV has changed to I2C_WE (wakeup enable) */
53 enum {
54 OMAP_I2C_REV_REG = 0,
55 OMAP_I2C_IE_REG,
56 OMAP_I2C_STAT_REG,
57 OMAP_I2C_IV_REG,
58 OMAP_I2C_WE_REG,
59 OMAP_I2C_SYSS_REG,
60 OMAP_I2C_BUF_REG,
61 OMAP_I2C_CNT_REG,
62 OMAP_I2C_DATA_REG,
63 OMAP_I2C_SYSC_REG,
64 OMAP_I2C_CON_REG,
65 OMAP_I2C_OA_REG,
66 OMAP_I2C_SA_REG,
67 OMAP_I2C_PSC_REG,
68 OMAP_I2C_SCLL_REG,
69 OMAP_I2C_SCLH_REG,
70 OMAP_I2C_SYSTEST_REG,
71 OMAP_I2C_BUFSTAT_REG,
72 /* only on OMAP4430 */
73 OMAP_I2C_IP_V2_REVNB_LO,
74 OMAP_I2C_IP_V2_REVNB_HI,
75 OMAP_I2C_IP_V2_IRQSTATUS_RAW,
76 OMAP_I2C_IP_V2_IRQENABLE_SET,
77 OMAP_I2C_IP_V2_IRQENABLE_CLR,
78 };
79
80 /* I2C Interrupt Enable Register (OMAP_I2C_IE): */
81 #define OMAP_I2C_IE_XDR (1 << 14) /* TX Buffer drain int enable */
82 #define OMAP_I2C_IE_RDR (1 << 13) /* RX Buffer drain int enable */
83 #define OMAP_I2C_IE_XRDY (1 << 4) /* TX data ready int enable */
84 #define OMAP_I2C_IE_RRDY (1 << 3) /* RX data ready int enable */
85 #define OMAP_I2C_IE_ARDY (1 << 2) /* Access ready int enable */
86 #define OMAP_I2C_IE_NACK (1 << 1) /* No ack interrupt enable */
87 #define OMAP_I2C_IE_AL (1 << 0) /* Arbitration lost int ena */
88
89 /* I2C Status Register (OMAP_I2C_STAT): */
90 #define OMAP_I2C_STAT_XDR (1 << 14) /* TX Buffer draining */
91 #define OMAP_I2C_STAT_RDR (1 << 13) /* RX Buffer draining */
92 #define OMAP_I2C_STAT_BB (1 << 12) /* Bus busy */
93 #define OMAP_I2C_STAT_ROVR (1 << 11) /* Receive overrun */
94 #define OMAP_I2C_STAT_XUDF (1 << 10) /* Transmit underflow */
95 #define OMAP_I2C_STAT_AAS (1 << 9) /* Address as slave */
96 #define OMAP_I2C_STAT_BF (1 << 8) /* Bus Free */
97 #define OMAP_I2C_STAT_XRDY (1 << 4) /* Transmit data ready */
98 #define OMAP_I2C_STAT_RRDY (1 << 3) /* Receive data ready */
99 #define OMAP_I2C_STAT_ARDY (1 << 2) /* Register access ready */
100 #define OMAP_I2C_STAT_NACK (1 << 1) /* No ack interrupt enable */
101 #define OMAP_I2C_STAT_AL (1 << 0) /* Arbitration lost int ena */
102
103 /* I2C WE wakeup enable register */
104 #define OMAP_I2C_WE_XDR_WE (1 << 14) /* TX drain wakup */
105 #define OMAP_I2C_WE_RDR_WE (1 << 13) /* RX drain wakeup */
106 #define OMAP_I2C_WE_AAS_WE (1 << 9) /* Address as slave wakeup*/
107 #define OMAP_I2C_WE_BF_WE (1 << 8) /* Bus free wakeup */
108 #define OMAP_I2C_WE_STC_WE (1 << 6) /* Start condition wakeup */
109 #define OMAP_I2C_WE_GC_WE (1 << 5) /* General call wakeup */
110 #define OMAP_I2C_WE_DRDY_WE (1 << 3) /* TX/RX data ready wakeup */
111 #define OMAP_I2C_WE_ARDY_WE (1 << 2) /* Reg access ready wakeup */
112 #define OMAP_I2C_WE_NACK_WE (1 << 1) /* No acknowledgment wakeup */
113 #define OMAP_I2C_WE_AL_WE (1 << 0) /* Arbitration lost wakeup */
114
115 #define OMAP_I2C_WE_ALL (OMAP_I2C_WE_XDR_WE | OMAP_I2C_WE_RDR_WE | \
116 OMAP_I2C_WE_AAS_WE | OMAP_I2C_WE_BF_WE | \
117 OMAP_I2C_WE_STC_WE | OMAP_I2C_WE_GC_WE | \
118 OMAP_I2C_WE_DRDY_WE | OMAP_I2C_WE_ARDY_WE | \
119 OMAP_I2C_WE_NACK_WE | OMAP_I2C_WE_AL_WE)
120
121 /* I2C Buffer Configuration Register (OMAP_I2C_BUF): */
122 #define OMAP_I2C_BUF_RDMA_EN (1 << 15) /* RX DMA channel enable */
123 #define OMAP_I2C_BUF_RXFIF_CLR (1 << 14) /* RX FIFO Clear */
124 #define OMAP_I2C_BUF_XDMA_EN (1 << 7) /* TX DMA channel enable */
125 #define OMAP_I2C_BUF_TXFIF_CLR (1 << 6) /* TX FIFO Clear */
126
127 /* I2C Configuration Register (OMAP_I2C_CON): */
128 #define OMAP_I2C_CON_EN (1 << 15) /* I2C module enable */
129 #define OMAP_I2C_CON_BE (1 << 14) /* Big endian mode */
130 #define OMAP_I2C_CON_OPMODE_HS (1 << 12) /* High Speed support */
131 #define OMAP_I2C_CON_STB (1 << 11) /* Start byte mode (master) */
132 #define OMAP_I2C_CON_MST (1 << 10) /* Master/slave mode */
133 #define OMAP_I2C_CON_TRX (1 << 9) /* TX/RX mode (master only) */
134 #define OMAP_I2C_CON_XA (1 << 8) /* Expand address */
135 #define OMAP_I2C_CON_RM (1 << 2) /* Repeat mode (master only) */
136 #define OMAP_I2C_CON_STP (1 << 1) /* Stop cond (master only) */
137 #define OMAP_I2C_CON_STT (1 << 0) /* Start condition (master) */
138
139 /* I2C SCL time value when Master */
140 #define OMAP_I2C_SCLL_HSSCLL 8
141 #define OMAP_I2C_SCLH_HSSCLH 8
142
143 /* I2C System Test Register (OMAP_I2C_SYSTEST): */
144 #define OMAP_I2C_SYSTEST_ST_EN (1 << 15) /* System test enable */
145 #define OMAP_I2C_SYSTEST_FREE (1 << 14) /* Free running mode */
146 #define OMAP_I2C_SYSTEST_TMODE_MASK (3 << 12) /* Test mode select */
147 #define OMAP_I2C_SYSTEST_TMODE_SHIFT (12) /* Test mode select */
148 /* Functional mode */
149 #define OMAP_I2C_SYSTEST_SCL_I_FUNC (1 << 8) /* SCL line input value */
150 #define OMAP_I2C_SYSTEST_SCL_O_FUNC (1 << 7) /* SCL line output value */
151 #define OMAP_I2C_SYSTEST_SDA_I_FUNC (1 << 6) /* SDA line input value */
152 #define OMAP_I2C_SYSTEST_SDA_O_FUNC (1 << 5) /* SDA line output value */
153 /* SDA/SCL IO mode */
154 #define OMAP_I2C_SYSTEST_SCL_I (1 << 3) /* SCL line sense in */
155 #define OMAP_I2C_SYSTEST_SCL_O (1 << 2) /* SCL line drive out */
156 #define OMAP_I2C_SYSTEST_SDA_I (1 << 1) /* SDA line sense in */
157 #define OMAP_I2C_SYSTEST_SDA_O (1 << 0) /* SDA line drive out */
158
159 /* OCP_SYSSTATUS bit definitions */
160 #define SYSS_RESETDONE_MASK (1 << 0)
161
162 /* OCP_SYSCONFIG bit definitions */
163 #define SYSC_CLOCKACTIVITY_MASK (0x3 << 8)
164 #define SYSC_SIDLEMODE_MASK (0x3 << 3)
165 #define SYSC_ENAWAKEUP_MASK (1 << 2)
166 #define SYSC_SOFTRESET_MASK (1 << 1)
167 #define SYSC_AUTOIDLE_MASK (1 << 0)
168
169 #define SYSC_IDLEMODE_SMART 0x2
170 #define SYSC_CLOCKACTIVITY_FCLK 0x2
171
172 /* Errata definitions */
173 #define I2C_OMAP_ERRATA_I207 (1 << 0)
174 #define I2C_OMAP_ERRATA_I462 (1 << 1)
175
176 #define OMAP_I2C_IP_V2_INTERRUPTS_MASK 0x6FFF
177
178 struct omap_i2c_dev {
179 struct device *dev;
180 void __iomem *base; /* virtual */
181 int irq;
182 int reg_shift; /* bit shift for I2C register addresses */
183 struct completion cmd_complete;
184 struct resource *ioarea;
185 u32 latency; /* maximum mpu wkup latency */
186 void (*set_mpu_wkup_lat)(struct device *dev,
187 long latency);
188 u32 speed; /* Speed of bus in kHz */
189 u32 flags;
190 u16 scheme;
191 u16 cmd_err;
192 u8 *buf;
193 u8 *regs;
194 size_t buf_len;
195 struct i2c_adapter adapter;
196 u8 threshold;
197 u8 fifo_size; /* use as flag and value
198 * fifo_size==0 implies no fifo
199 * if set, should be trsh+1
200 */
201 u32 rev;
202 unsigned b_hw:1; /* bad h/w fixes */
203 unsigned bb_valid:1; /* true when BB-bit reflects
204 * the I2C bus state
205 */
206 unsigned receiver:1; /* true when we're in receiver mode */
207 u16 iestate; /* Saved interrupt register */
208 u16 pscstate;
209 u16 scllstate;
210 u16 sclhstate;
211 u16 syscstate;
212 u16 westate;
213 u16 errata;
214 };
215
216 static const u8 reg_map_ip_v1[] = {
217 [OMAP_I2C_REV_REG] = 0x00,
218 [OMAP_I2C_IE_REG] = 0x01,
219 [OMAP_I2C_STAT_REG] = 0x02,
220 [OMAP_I2C_IV_REG] = 0x03,
221 [OMAP_I2C_WE_REG] = 0x03,
222 [OMAP_I2C_SYSS_REG] = 0x04,
223 [OMAP_I2C_BUF_REG] = 0x05,
224 [OMAP_I2C_CNT_REG] = 0x06,
225 [OMAP_I2C_DATA_REG] = 0x07,
226 [OMAP_I2C_SYSC_REG] = 0x08,
227 [OMAP_I2C_CON_REG] = 0x09,
228 [OMAP_I2C_OA_REG] = 0x0a,
229 [OMAP_I2C_SA_REG] = 0x0b,
230 [OMAP_I2C_PSC_REG] = 0x0c,
231 [OMAP_I2C_SCLL_REG] = 0x0d,
232 [OMAP_I2C_SCLH_REG] = 0x0e,
233 [OMAP_I2C_SYSTEST_REG] = 0x0f,
234 [OMAP_I2C_BUFSTAT_REG] = 0x10,
235 };
236
237 static const u8 reg_map_ip_v2[] = {
238 [OMAP_I2C_REV_REG] = 0x04,
239 [OMAP_I2C_IE_REG] = 0x2c,
240 [OMAP_I2C_STAT_REG] = 0x28,
241 [OMAP_I2C_IV_REG] = 0x34,
242 [OMAP_I2C_WE_REG] = 0x34,
243 [OMAP_I2C_SYSS_REG] = 0x90,
244 [OMAP_I2C_BUF_REG] = 0x94,
245 [OMAP_I2C_CNT_REG] = 0x98,
246 [OMAP_I2C_DATA_REG] = 0x9c,
247 [OMAP_I2C_SYSC_REG] = 0x10,
248 [OMAP_I2C_CON_REG] = 0xa4,
249 [OMAP_I2C_OA_REG] = 0xa8,
250 [OMAP_I2C_SA_REG] = 0xac,
251 [OMAP_I2C_PSC_REG] = 0xb0,
252 [OMAP_I2C_SCLL_REG] = 0xb4,
253 [OMAP_I2C_SCLH_REG] = 0xb8,
254 [OMAP_I2C_SYSTEST_REG] = 0xbC,
255 [OMAP_I2C_BUFSTAT_REG] = 0xc0,
256 [OMAP_I2C_IP_V2_REVNB_LO] = 0x00,
257 [OMAP_I2C_IP_V2_REVNB_HI] = 0x04,
258 [OMAP_I2C_IP_V2_IRQSTATUS_RAW] = 0x24,
259 [OMAP_I2C_IP_V2_IRQENABLE_SET] = 0x2c,
260 [OMAP_I2C_IP_V2_IRQENABLE_CLR] = 0x30,
261 };
262
263 static int omap_i2c_xfer_data(struct omap_i2c_dev *omap);
264
265 static inline void omap_i2c_write_reg(struct omap_i2c_dev *omap,
266 int reg, u16 val)
267 {
268 writew_relaxed(val, omap->base +
269 (omap->regs[reg] << omap->reg_shift));
270 }
271
272 static inline u16 omap_i2c_read_reg(struct omap_i2c_dev *omap, int reg)
273 {
274 return readw_relaxed(omap->base +
275 (omap->regs[reg] << omap->reg_shift));
276 }
277
278 static void __omap_i2c_init(struct omap_i2c_dev *omap)
279 {
280
281 omap_i2c_write_reg(omap, OMAP_I2C_CON_REG, 0);
282
283 /* Setup clock prescaler to obtain approx 12MHz I2C module clock: */
284 omap_i2c_write_reg(omap, OMAP_I2C_PSC_REG, omap->pscstate);
285
286 /* SCL low and high time values */
287 omap_i2c_write_reg(omap, OMAP_I2C_SCLL_REG, omap->scllstate);
288 omap_i2c_write_reg(omap, OMAP_I2C_SCLH_REG, omap->sclhstate);
289 if (omap->rev >= OMAP_I2C_REV_ON_3430_3530)
290 omap_i2c_write_reg(omap, OMAP_I2C_WE_REG, omap->westate);
291
292 /* Take the I2C module out of reset: */
293 omap_i2c_write_reg(omap, OMAP_I2C_CON_REG, OMAP_I2C_CON_EN);
294
295 /*
296 * NOTE: right after setting CON_EN, STAT_BB could be 0 while the
297 * bus is busy. It will be changed to 1 on the next IP FCLK clock.
298 * udelay(1) will be enough to fix that.
299 */
300
301 /*
302 * Don't write to this register if the IE state is 0 as it can
303 * cause deadlock.
304 */
305 if (omap->iestate)
306 omap_i2c_write_reg(omap, OMAP_I2C_IE_REG, omap->iestate);
307 }
308
309 static int omap_i2c_reset(struct omap_i2c_dev *omap)
310 {
311 unsigned long timeout;
312 u16 sysc;
313
314 if (omap->rev >= OMAP_I2C_OMAP1_REV_2) {
315 sysc = omap_i2c_read_reg(omap, OMAP_I2C_SYSC_REG);
316
317 /* Disable I2C controller before soft reset */
318 omap_i2c_write_reg(omap, OMAP_I2C_CON_REG,
319 omap_i2c_read_reg(omap, OMAP_I2C_CON_REG) &
320 ~(OMAP_I2C_CON_EN));
321
322 omap_i2c_write_reg(omap, OMAP_I2C_SYSC_REG, SYSC_SOFTRESET_MASK);
323 /* For some reason we need to set the EN bit before the
324 * reset done bit gets set. */
325 timeout = jiffies + OMAP_I2C_TIMEOUT;
326 omap_i2c_write_reg(omap, OMAP_I2C_CON_REG, OMAP_I2C_CON_EN);
327 while (!(omap_i2c_read_reg(omap, OMAP_I2C_SYSS_REG) &
328 SYSS_RESETDONE_MASK)) {
329 if (time_after(jiffies, timeout)) {
330 dev_warn(omap->dev, "timeout waiting "
331 "for controller reset\n");
332 return -ETIMEDOUT;
333 }
334 msleep(1);
335 }
336
337 /* SYSC register is cleared by the reset; rewrite it */
338 omap_i2c_write_reg(omap, OMAP_I2C_SYSC_REG, sysc);
339
340 if (omap->rev > OMAP_I2C_REV_ON_3430_3530) {
341 /* Schedule I2C-bus monitoring on the next transfer */
342 omap->bb_valid = 0;
343 }
344 }
345
346 return 0;
347 }
348
349 static int omap_i2c_init(struct omap_i2c_dev *omap)
350 {
351 u16 psc = 0, scll = 0, sclh = 0;
352 u16 fsscll = 0, fssclh = 0, hsscll = 0, hssclh = 0;
353 unsigned long fclk_rate = 12000000;
354 unsigned long internal_clk = 0;
355 struct clk *fclk;
356 int error;
357
358 if (omap->rev >= OMAP_I2C_REV_ON_3430_3530) {
359 /*
360 * Enabling all wakup sources to stop I2C freezing on
361 * WFI instruction.
362 * REVISIT: Some wkup sources might not be needed.
363 */
364 omap->westate = OMAP_I2C_WE_ALL;
365 }
366
367 if (omap->flags & OMAP_I2C_FLAG_ALWAYS_ARMXOR_CLK) {
368 /*
369 * The I2C functional clock is the armxor_ck, so there's
370 * no need to get "armxor_ck" separately. Now, if OMAP2420
371 * always returns 12MHz for the functional clock, we can
372 * do this bit unconditionally.
373 */
374 fclk = clk_get(omap->dev, "fck");
375 if (IS_ERR(fclk)) {
376 error = PTR_ERR(fclk);
377 dev_err(omap->dev, "could not get fck: %i\n", error);
378
379 return error;
380 }
381
382 fclk_rate = clk_get_rate(fclk);
383 clk_put(fclk);
384
385 /* TRM for 5912 says the I2C clock must be prescaled to be
386 * between 7 - 12 MHz. The XOR input clock is typically
387 * 12, 13 or 19.2 MHz. So we should have code that produces:
388 *
389 * XOR MHz Divider Prescaler
390 * 12 1 0
391 * 13 2 1
392 * 19.2 2 1
393 */
394 if (fclk_rate > 12000000)
395 psc = fclk_rate / 12000000;
396 }
397
398 if (!(omap->flags & OMAP_I2C_FLAG_SIMPLE_CLOCK)) {
399
400 /*
401 * HSI2C controller internal clk rate should be 19.2 Mhz for
402 * HS and for all modes on 2430. On 34xx we can use lower rate
403 * to get longer filter period for better noise suppression.
404 * The filter is iclk (fclk for HS) period.
405 */
406 if (omap->speed > 400 ||
407 omap->flags & OMAP_I2C_FLAG_FORCE_19200_INT_CLK)
408 internal_clk = 19200;
409 else if (omap->speed > 100)
410 internal_clk = 9600;
411 else
412 internal_clk = 4000;
413 fclk = clk_get(omap->dev, "fck");
414 if (IS_ERR(fclk)) {
415 error = PTR_ERR(fclk);
416 dev_err(omap->dev, "could not get fck: %i\n", error);
417
418 return error;
419 }
420 fclk_rate = clk_get_rate(fclk) / 1000;
421 clk_put(fclk);
422
423 /* Compute prescaler divisor */
424 psc = fclk_rate / internal_clk;
425 psc = psc - 1;
426
427 /* If configured for High Speed */
428 if (omap->speed > 400) {
429 unsigned long scl;
430
431 /* For first phase of HS mode */
432 scl = internal_clk / 400;
433 fsscll = scl - (scl / 3) - 7;
434 fssclh = (scl / 3) - 5;
435
436 /* For second phase of HS mode */
437 scl = fclk_rate / omap->speed;
438 hsscll = scl - (scl / 3) - 7;
439 hssclh = (scl / 3) - 5;
440 } else if (omap->speed > 100) {
441 unsigned long scl;
442
443 /* Fast mode */
444 scl = internal_clk / omap->speed;
445 fsscll = scl - (scl / 3) - 7;
446 fssclh = (scl / 3) - 5;
447 } else {
448 /* Standard mode */
449 fsscll = internal_clk / (omap->speed * 2) - 7;
450 fssclh = internal_clk / (omap->speed * 2) - 5;
451 }
452 scll = (hsscll << OMAP_I2C_SCLL_HSSCLL) | fsscll;
453 sclh = (hssclh << OMAP_I2C_SCLH_HSSCLH) | fssclh;
454 } else {
455 /* Program desired operating rate */
456 fclk_rate /= (psc + 1) * 1000;
457 if (psc > 2)
458 psc = 2;
459 scll = fclk_rate / (omap->speed * 2) - 7 + psc;
460 sclh = fclk_rate / (omap->speed * 2) - 7 + psc;
461 }
462
463 omap->iestate = (OMAP_I2C_IE_XRDY | OMAP_I2C_IE_RRDY |
464 OMAP_I2C_IE_ARDY | OMAP_I2C_IE_NACK |
465 OMAP_I2C_IE_AL) | ((omap->fifo_size) ?
466 (OMAP_I2C_IE_RDR | OMAP_I2C_IE_XDR) : 0);
467
468 omap->pscstate = psc;
469 omap->scllstate = scll;
470 omap->sclhstate = sclh;
471
472 if (omap->rev <= OMAP_I2C_REV_ON_3430_3530) {
473 /* Not implemented */
474 omap->bb_valid = 1;
475 }
476
477 __omap_i2c_init(omap);
478
479 return 0;
480 }
481
482 /*
483 * Try bus recovery, but only if SDA is actually low.
484 */
485 static int omap_i2c_recover_bus(struct omap_i2c_dev *omap)
486 {
487 u16 systest;
488
489 systest = omap_i2c_read_reg(omap, OMAP_I2C_SYSTEST_REG);
490 if ((systest & OMAP_I2C_SYSTEST_SCL_I_FUNC) &&
491 (systest & OMAP_I2C_SYSTEST_SDA_I_FUNC))
492 return 0; /* bus seems to already be fine */
493 if (!(systest & OMAP_I2C_SYSTEST_SCL_I_FUNC))
494 return -EBUSY; /* recovery would not fix SCL */
495 return i2c_recover_bus(&omap->adapter);
496 }
497
498 /*
499 * Waiting on Bus Busy
500 */
501 static int omap_i2c_wait_for_bb(struct omap_i2c_dev *omap)
502 {
503 unsigned long timeout;
504
505 timeout = jiffies + OMAP_I2C_TIMEOUT;
506 while (omap_i2c_read_reg(omap, OMAP_I2C_STAT_REG) & OMAP_I2C_STAT_BB) {
507 if (time_after(jiffies, timeout))
508 return omap_i2c_recover_bus(omap);
509 msleep(1);
510 }
511
512 return 0;
513 }
514
515 /*
516 * Wait while BB-bit doesn't reflect the I2C bus state
517 *
518 * In a multimaster environment, after IP software reset, BB-bit value doesn't
519 * correspond to the current bus state. It may happen what BB-bit will be 0,
520 * while the bus is busy due to another I2C master activity.
521 * Here are BB-bit values after reset:
522 * SDA SCL BB NOTES
523 * 0 0 0 1, 2
524 * 1 0 0 1, 2
525 * 0 1 1
526 * 1 1 0 3
527 * Later, if IP detect SDA=0 and SCL=1 (ACK) or SDA 1->0 while SCL=1 (START)
528 * combinations on the bus, it set BB-bit to 1.
529 * If IP detect SDA 0->1 while SCL=1 (STOP) combination on the bus,
530 * it set BB-bit to 0 and BF to 1.
531 * BB and BF bits correctly tracks the bus state while IP is suspended
532 * BB bit became valid on the next FCLK clock after CON_EN bit set
533 *
534 * NOTES:
535 * 1. Any transfer started when BB=0 and bus is busy wouldn't be
536 * completed by IP and results in controller timeout.
537 * 2. Any transfer started when BB=0 and SCL=0 results in IP
538 * starting to drive SDA low. In that case IP corrupt data
539 * on the bus.
540 * 3. Any transfer started in the middle of another master's transfer
541 * results in unpredictable results and data corruption
542 */
543 static int omap_i2c_wait_for_bb_valid(struct omap_i2c_dev *omap)
544 {
545 unsigned long bus_free_timeout = 0;
546 unsigned long timeout;
547 int bus_free = 0;
548 u16 stat, systest;
549
550 if (omap->bb_valid)
551 return 0;
552
553 timeout = jiffies + OMAP_I2C_TIMEOUT;
554 while (1) {
555 stat = omap_i2c_read_reg(omap, OMAP_I2C_STAT_REG);
556 /*
557 * We will see BB or BF event in a case IP had detected any
558 * activity on the I2C bus. Now IP correctly tracks the bus
559 * state. BB-bit value is valid.
560 */
561 if (stat & (OMAP_I2C_STAT_BB | OMAP_I2C_STAT_BF))
562 break;
563
564 /*
565 * Otherwise, we must look signals on the bus to make
566 * the right decision.
567 */
568 systest = omap_i2c_read_reg(omap, OMAP_I2C_SYSTEST_REG);
569 if ((systest & OMAP_I2C_SYSTEST_SCL_I_FUNC) &&
570 (systest & OMAP_I2C_SYSTEST_SDA_I_FUNC)) {
571 if (!bus_free) {
572 bus_free_timeout = jiffies +
573 OMAP_I2C_BUS_FREE_TIMEOUT;
574 bus_free = 1;
575 }
576
577 /*
578 * SDA and SCL lines was high for 10 ms without bus
579 * activity detected. The bus is free. Consider
580 * BB-bit value is valid.
581 */
582 if (time_after(jiffies, bus_free_timeout))
583 break;
584 } else {
585 bus_free = 0;
586 }
587
588 if (time_after(jiffies, timeout)) {
589 /*
590 * SDA or SCL were low for the entire timeout without
591 * any activity detected. Most likely, a slave is
592 * locking up the bus with no master driving the clock.
593 */
594 dev_warn(omap->dev, "timeout waiting for bus ready\n");
595 return omap_i2c_recover_bus(omap);
596 }
597
598 msleep(1);
599 }
600
601 omap->bb_valid = 1;
602 return 0;
603 }
604
605 static void omap_i2c_resize_fifo(struct omap_i2c_dev *omap, u8 size, bool is_rx)
606 {
607 u16 buf;
608
609 if (omap->flags & OMAP_I2C_FLAG_NO_FIFO)
610 return;
611
612 /*
613 * Set up notification threshold based on message size. We're doing
614 * this to try and avoid draining feature as much as possible. Whenever
615 * we have big messages to transfer (bigger than our total fifo size)
616 * then we might use draining feature to transfer the remaining bytes.
617 */
618
619 omap->threshold = clamp(size, (u8) 1, omap->fifo_size);
620
621 buf = omap_i2c_read_reg(omap, OMAP_I2C_BUF_REG);
622
623 if (is_rx) {
624 /* Clear RX Threshold */
625 buf &= ~(0x3f << 8);
626 buf |= ((omap->threshold - 1) << 8) | OMAP_I2C_BUF_RXFIF_CLR;
627 } else {
628 /* Clear TX Threshold */
629 buf &= ~0x3f;
630 buf |= (omap->threshold - 1) | OMAP_I2C_BUF_TXFIF_CLR;
631 }
632
633 omap_i2c_write_reg(omap, OMAP_I2C_BUF_REG, buf);
634
635 if (omap->rev < OMAP_I2C_REV_ON_3630)
636 omap->b_hw = 1; /* Enable hardware fixes */
637
638 /* calculate wakeup latency constraint for MPU */
639 if (omap->set_mpu_wkup_lat != NULL)
640 omap->latency = (1000000 * omap->threshold) /
641 (1000 * omap->speed / 8);
642 }
643
644 static void omap_i2c_wait(struct omap_i2c_dev *omap)
645 {
646 u16 stat;
647 u16 mask = omap_i2c_read_reg(omap, OMAP_I2C_IE_REG);
648 int count = 0;
649
650 do {
651 stat = omap_i2c_read_reg(omap, OMAP_I2C_STAT_REG);
652 count++;
653 } while (!(stat & mask) && count < 5);
654 }
655
656 /*
657 * Low level master read/write transaction.
658 */
659 static int omap_i2c_xfer_msg(struct i2c_adapter *adap,
660 struct i2c_msg *msg, int stop, bool polling)
661 {
662 struct omap_i2c_dev *omap = i2c_get_adapdata(adap);
663 unsigned long timeout;
664 u16 w;
665 int ret;
666
667 dev_dbg(omap->dev, "addr: 0x%04x, len: %d, flags: 0x%x, stop: %d\n",
668 msg->addr, msg->len, msg->flags, stop);
669
670 omap->receiver = !!(msg->flags & I2C_M_RD);
671 omap_i2c_resize_fifo(omap, msg->len, omap->receiver);
672
673 omap_i2c_write_reg(omap, OMAP_I2C_SA_REG, msg->addr);
674
675 /* REVISIT: Could the STB bit of I2C_CON be used with probing? */
676 omap->buf = msg->buf;
677 omap->buf_len = msg->len;
678
679 /* make sure writes to omap->buf_len are ordered */
680 barrier();
681
682 omap_i2c_write_reg(omap, OMAP_I2C_CNT_REG, omap->buf_len);
683
684 /* Clear the FIFO Buffers */
685 w = omap_i2c_read_reg(omap, OMAP_I2C_BUF_REG);
686 w |= OMAP_I2C_BUF_RXFIF_CLR | OMAP_I2C_BUF_TXFIF_CLR;
687 omap_i2c_write_reg(omap, OMAP_I2C_BUF_REG, w);
688
689 if (!polling)
690 reinit_completion(&omap->cmd_complete);
691 omap->cmd_err = 0;
692
693 w = OMAP_I2C_CON_EN | OMAP_I2C_CON_MST | OMAP_I2C_CON_STT;
694
695 /* High speed configuration */
696 if (omap->speed > 400)
697 w |= OMAP_I2C_CON_OPMODE_HS;
698
699 if (msg->flags & I2C_M_STOP)
700 stop = 1;
701 if (msg->flags & I2C_M_TEN)
702 w |= OMAP_I2C_CON_XA;
703 if (!(msg->flags & I2C_M_RD))
704 w |= OMAP_I2C_CON_TRX;
705
706 if (!omap->b_hw && stop)
707 w |= OMAP_I2C_CON_STP;
708 /*
709 * NOTE: STAT_BB bit could became 1 here if another master occupy
710 * the bus. IP successfully complete transfer when the bus will be
711 * free again (BB reset to 0).
712 */
713 omap_i2c_write_reg(omap, OMAP_I2C_CON_REG, w);
714
715 /*
716 * Don't write stt and stp together on some hardware.
717 */
718 if (omap->b_hw && stop) {
719 unsigned long delay = jiffies + OMAP_I2C_TIMEOUT;
720 u16 con = omap_i2c_read_reg(omap, OMAP_I2C_CON_REG);
721 while (con & OMAP_I2C_CON_STT) {
722 con = omap_i2c_read_reg(omap, OMAP_I2C_CON_REG);
723
724 /* Let the user know if i2c is in a bad state */
725 if (time_after(jiffies, delay)) {
726 dev_err(omap->dev, "controller timed out "
727 "waiting for start condition to finish\n");
728 return -ETIMEDOUT;
729 }
730 cpu_relax();
731 }
732
733 w |= OMAP_I2C_CON_STP;
734 w &= ~OMAP_I2C_CON_STT;
735 omap_i2c_write_reg(omap, OMAP_I2C_CON_REG, w);
736 }
737
738 /*
739 * REVISIT: We should abort the transfer on signals, but the bus goes
740 * into arbitration and we're currently unable to recover from it.
741 */
742 if (!polling) {
743 timeout = wait_for_completion_timeout(&omap->cmd_complete,
744 OMAP_I2C_TIMEOUT);
745 } else {
746 do {
747 omap_i2c_wait(omap);
748 ret = omap_i2c_xfer_data(omap);
749 } while (ret == -EAGAIN);
750
751 timeout = !ret;
752 }
753
754 if (timeout == 0) {
755 dev_err(omap->dev, "controller timed out\n");
756 omap_i2c_reset(omap);
757 __omap_i2c_init(omap);
758 return -ETIMEDOUT;
759 }
760
761 if (likely(!omap->cmd_err))
762 return 0;
763
764 /* We have an error */
765 if (omap->cmd_err & (OMAP_I2C_STAT_ROVR | OMAP_I2C_STAT_XUDF)) {
766 omap_i2c_reset(omap);
767 __omap_i2c_init(omap);
768 return -EIO;
769 }
770
771 if (omap->cmd_err & OMAP_I2C_STAT_AL)
772 return -EAGAIN;
773
774 if (omap->cmd_err & OMAP_I2C_STAT_NACK) {
775 if (msg->flags & I2C_M_IGNORE_NAK)
776 return 0;
777
778 w = omap_i2c_read_reg(omap, OMAP_I2C_CON_REG);
779 w |= OMAP_I2C_CON_STP;
780 omap_i2c_write_reg(omap, OMAP_I2C_CON_REG, w);
781 return -EREMOTEIO;
782 }
783 return -EIO;
784 }
785
786
787 /*
788 * Prepare controller for a transaction and call omap_i2c_xfer_msg
789 * to do the work during IRQ processing.
790 */
791 static int
792 omap_i2c_xfer_common(struct i2c_adapter *adap, struct i2c_msg msgs[], int num,
793 bool polling)
794 {
795 struct omap_i2c_dev *omap = i2c_get_adapdata(adap);
796 int i;
797 int r;
798
799 r = pm_runtime_get_sync(omap->dev);
800 if (r < 0)
801 goto out;
802
803 r = omap_i2c_wait_for_bb_valid(omap);
804 if (r < 0)
805 goto out;
806
807 r = omap_i2c_wait_for_bb(omap);
808 if (r < 0)
809 goto out;
810
811 if (omap->set_mpu_wkup_lat != NULL)
812 omap->set_mpu_wkup_lat(omap->dev, omap->latency);
813
814 for (i = 0; i < num; i++) {
815 r = omap_i2c_xfer_msg(adap, &msgs[i], (i == (num - 1)),
816 polling);
817 if (r != 0)
818 break;
819 }
820
821 if (r == 0)
822 r = num;
823
824 omap_i2c_wait_for_bb(omap);
825
826 if (omap->set_mpu_wkup_lat != NULL)
827 omap->set_mpu_wkup_lat(omap->dev, -1);
828
829 out:
830 pm_runtime_mark_last_busy(omap->dev);
831 pm_runtime_put_autosuspend(omap->dev);
832 return r;
833 }
834
835 static int
836 omap_i2c_xfer_irq(struct i2c_adapter *adap, struct i2c_msg msgs[], int num)
837 {
838 return omap_i2c_xfer_common(adap, msgs, num, false);
839 }
840
841 static int
842 omap_i2c_xfer_polling(struct i2c_adapter *adap, struct i2c_msg msgs[], int num)
843 {
844 return omap_i2c_xfer_common(adap, msgs, num, true);
845 }
846
847 static u32
848 omap_i2c_func(struct i2c_adapter *adap)
849 {
850 return I2C_FUNC_I2C | (I2C_FUNC_SMBUS_EMUL & ~I2C_FUNC_SMBUS_QUICK) |
851 I2C_FUNC_PROTOCOL_MANGLING;
852 }
853
854 static inline void
855 omap_i2c_complete_cmd(struct omap_i2c_dev *omap, u16 err)
856 {
857 omap->cmd_err |= err;
858 complete(&omap->cmd_complete);
859 }
860
861 static inline void
862 omap_i2c_ack_stat(struct omap_i2c_dev *omap, u16 stat)
863 {
864 omap_i2c_write_reg(omap, OMAP_I2C_STAT_REG, stat);
865 }
866
867 static inline void i2c_omap_errata_i207(struct omap_i2c_dev *omap, u16 stat)
868 {
869 /*
870 * I2C Errata(Errata Nos. OMAP2: 1.67, OMAP3: 1.8)
871 * Not applicable for OMAP4.
872 * Under certain rare conditions, RDR could be set again
873 * when the bus is busy, then ignore the interrupt and
874 * clear the interrupt.
875 */
876 if (stat & OMAP_I2C_STAT_RDR) {
877 /* Step 1: If RDR is set, clear it */
878 omap_i2c_ack_stat(omap, OMAP_I2C_STAT_RDR);
879
880 /* Step 2: */
881 if (!(omap_i2c_read_reg(omap, OMAP_I2C_STAT_REG)
882 & OMAP_I2C_STAT_BB)) {
883
884 /* Step 3: */
885 if (omap_i2c_read_reg(omap, OMAP_I2C_STAT_REG)
886 & OMAP_I2C_STAT_RDR) {
887 omap_i2c_ack_stat(omap, OMAP_I2C_STAT_RDR);
888 dev_dbg(omap->dev, "RDR when bus is busy.\n");
889 }
890
891 }
892 }
893 }
894
895 /* rev1 devices are apparently only on some 15xx */
896 #ifdef CONFIG_ARCH_OMAP15XX
897
898 static irqreturn_t
899 omap_i2c_omap1_isr(int this_irq, void *dev_id)
900 {
901 struct omap_i2c_dev *omap = dev_id;
902 u16 iv, w;
903
904 if (pm_runtime_suspended(omap->dev))
905 return IRQ_NONE;
906
907 iv = omap_i2c_read_reg(omap, OMAP_I2C_IV_REG);
908 switch (iv) {
909 case 0x00: /* None */
910 break;
911 case 0x01: /* Arbitration lost */
912 dev_err(omap->dev, "Arbitration lost\n");
913 omap_i2c_complete_cmd(omap, OMAP_I2C_STAT_AL);
914 break;
915 case 0x02: /* No acknowledgement */
916 omap_i2c_complete_cmd(omap, OMAP_I2C_STAT_NACK);
917 omap_i2c_write_reg(omap, OMAP_I2C_CON_REG, OMAP_I2C_CON_STP);
918 break;
919 case 0x03: /* Register access ready */
920 omap_i2c_complete_cmd(omap, 0);
921 break;
922 case 0x04: /* Receive data ready */
923 if (omap->buf_len) {
924 w = omap_i2c_read_reg(omap, OMAP_I2C_DATA_REG);
925 *omap->buf++ = w;
926 omap->buf_len--;
927 if (omap->buf_len) {
928 *omap->buf++ = w >> 8;
929 omap->buf_len--;
930 }
931 } else
932 dev_err(omap->dev, "RRDY IRQ while no data requested\n");
933 break;
934 case 0x05: /* Transmit data ready */
935 if (omap->buf_len) {
936 w = *omap->buf++;
937 omap->buf_len--;
938 if (omap->buf_len) {
939 w |= *omap->buf++ << 8;
940 omap->buf_len--;
941 }
942 omap_i2c_write_reg(omap, OMAP_I2C_DATA_REG, w);
943 } else
944 dev_err(omap->dev, "XRDY IRQ while no data to send\n");
945 break;
946 default:
947 return IRQ_NONE;
948 }
949
950 return IRQ_HANDLED;
951 }
952 #else
953 #define omap_i2c_omap1_isr NULL
954 #endif
955
956 /*
957 * OMAP3430 Errata i462: When an XRDY/XDR is hit, wait for XUDF before writing
958 * data to DATA_REG. Otherwise some data bytes can be lost while transferring
959 * them from the memory to the I2C interface.
960 */
961 static int errata_omap3_i462(struct omap_i2c_dev *omap)
962 {
963 unsigned long timeout = 10000;
964 u16 stat;
965
966 do {
967 stat = omap_i2c_read_reg(omap, OMAP_I2C_STAT_REG);
968 if (stat & OMAP_I2C_STAT_XUDF)
969 break;
970
971 if (stat & (OMAP_I2C_STAT_NACK | OMAP_I2C_STAT_AL)) {
972 omap_i2c_ack_stat(omap, (OMAP_I2C_STAT_XRDY |
973 OMAP_I2C_STAT_XDR));
974 if (stat & OMAP_I2C_STAT_NACK) {
975 omap->cmd_err |= OMAP_I2C_STAT_NACK;
976 omap_i2c_ack_stat(omap, OMAP_I2C_STAT_NACK);
977 }
978
979 if (stat & OMAP_I2C_STAT_AL) {
980 dev_err(omap->dev, "Arbitration lost\n");
981 omap->cmd_err |= OMAP_I2C_STAT_AL;
982 omap_i2c_ack_stat(omap, OMAP_I2C_STAT_AL);
983 }
984
985 return -EIO;
986 }
987
988 cpu_relax();
989 } while (--timeout);
990
991 if (!timeout) {
992 dev_err(omap->dev, "timeout waiting on XUDF bit\n");
993 return 0;
994 }
995
996 return 0;
997 }
998
999 static void omap_i2c_receive_data(struct omap_i2c_dev *omap, u8 num_bytes,
1000 bool is_rdr)
1001 {
1002 u16 w;
1003
1004 while (num_bytes--) {
1005 w = omap_i2c_read_reg(omap, OMAP_I2C_DATA_REG);
1006 *omap->buf++ = w;
1007 omap->buf_len--;
1008
1009 /*
1010 * Data reg in 2430, omap3 and
1011 * omap4 is 8 bit wide
1012 */
1013 if (omap->flags & OMAP_I2C_FLAG_16BIT_DATA_REG) {
1014 *omap->buf++ = w >> 8;
1015 omap->buf_len--;
1016 }
1017 }
1018 }
1019
1020 static int omap_i2c_transmit_data(struct omap_i2c_dev *omap, u8 num_bytes,
1021 bool is_xdr)
1022 {
1023 u16 w;
1024
1025 while (num_bytes--) {
1026 w = *omap->buf++;
1027 omap->buf_len--;
1028
1029 /*
1030 * Data reg in 2430, omap3 and
1031 * omap4 is 8 bit wide
1032 */
1033 if (omap->flags & OMAP_I2C_FLAG_16BIT_DATA_REG) {
1034 w |= *omap->buf++ << 8;
1035 omap->buf_len--;
1036 }
1037
1038 if (omap->errata & I2C_OMAP_ERRATA_I462) {
1039 int ret;
1040
1041 ret = errata_omap3_i462(omap);
1042 if (ret < 0)
1043 return ret;
1044 }
1045
1046 omap_i2c_write_reg(omap, OMAP_I2C_DATA_REG, w);
1047 }
1048
1049 return 0;
1050 }
1051
1052 static irqreturn_t
1053 omap_i2c_isr(int irq, void *dev_id)
1054 {
1055 struct omap_i2c_dev *omap = dev_id;
1056 irqreturn_t ret = IRQ_HANDLED;
1057 u16 mask;
1058 u16 stat;
1059
1060 stat = omap_i2c_read_reg(omap, OMAP_I2C_STAT_REG);
1061 mask = omap_i2c_read_reg(omap, OMAP_I2C_IE_REG);
1062
1063 if (stat & mask)
1064 ret = IRQ_WAKE_THREAD;
1065
1066 return ret;
1067 }
1068
1069 static int omap_i2c_xfer_data(struct omap_i2c_dev *omap)
1070 {
1071 u16 bits;
1072 u16 stat;
1073 int err = 0, count = 0;
1074
1075 do {
1076 bits = omap_i2c_read_reg(omap, OMAP_I2C_IE_REG);
1077 stat = omap_i2c_read_reg(omap, OMAP_I2C_STAT_REG);
1078 stat &= bits;
1079
1080 /* If we're in receiver mode, ignore XDR/XRDY */
1081 if (omap->receiver)
1082 stat &= ~(OMAP_I2C_STAT_XDR | OMAP_I2C_STAT_XRDY);
1083 else
1084 stat &= ~(OMAP_I2C_STAT_RDR | OMAP_I2C_STAT_RRDY);
1085
1086 if (!stat) {
1087 /* my work here is done */
1088 err = -EAGAIN;
1089 break;
1090 }
1091
1092 dev_dbg(omap->dev, "IRQ (ISR = 0x%04x)\n", stat);
1093 if (count++ == 100) {
1094 dev_warn(omap->dev, "Too much work in one IRQ\n");
1095 break;
1096 }
1097
1098 if (stat & OMAP_I2C_STAT_NACK) {
1099 err |= OMAP_I2C_STAT_NACK;
1100 omap_i2c_ack_stat(omap, OMAP_I2C_STAT_NACK);
1101 }
1102
1103 if (stat & OMAP_I2C_STAT_AL) {
1104 dev_err(omap->dev, "Arbitration lost\n");
1105 err |= OMAP_I2C_STAT_AL;
1106 omap_i2c_ack_stat(omap, OMAP_I2C_STAT_AL);
1107 }
1108
1109 /*
1110 * ProDB0017052: Clear ARDY bit twice
1111 */
1112 if (stat & OMAP_I2C_STAT_ARDY)
1113 omap_i2c_ack_stat(omap, OMAP_I2C_STAT_ARDY);
1114
1115 if (stat & (OMAP_I2C_STAT_ARDY | OMAP_I2C_STAT_NACK |
1116 OMAP_I2C_STAT_AL)) {
1117 omap_i2c_ack_stat(omap, (OMAP_I2C_STAT_RRDY |
1118 OMAP_I2C_STAT_RDR |
1119 OMAP_I2C_STAT_XRDY |
1120 OMAP_I2C_STAT_XDR |
1121 OMAP_I2C_STAT_ARDY));
1122 break;
1123 }
1124
1125 if (stat & OMAP_I2C_STAT_RDR) {
1126 u8 num_bytes = 1;
1127
1128 if (omap->fifo_size)
1129 num_bytes = omap->buf_len;
1130
1131 if (omap->errata & I2C_OMAP_ERRATA_I207) {
1132 i2c_omap_errata_i207(omap, stat);
1133 num_bytes = (omap_i2c_read_reg(omap,
1134 OMAP_I2C_BUFSTAT_REG) >> 8) & 0x3F;
1135 }
1136
1137 omap_i2c_receive_data(omap, num_bytes, true);
1138 omap_i2c_ack_stat(omap, OMAP_I2C_STAT_RDR);
1139 continue;
1140 }
1141
1142 if (stat & OMAP_I2C_STAT_RRDY) {
1143 u8 num_bytes = 1;
1144
1145 if (omap->threshold)
1146 num_bytes = omap->threshold;
1147
1148 omap_i2c_receive_data(omap, num_bytes, false);
1149 omap_i2c_ack_stat(omap, OMAP_I2C_STAT_RRDY);
1150 continue;
1151 }
1152
1153 if (stat & OMAP_I2C_STAT_XDR) {
1154 u8 num_bytes = 1;
1155 int ret;
1156
1157 if (omap->fifo_size)
1158 num_bytes = omap->buf_len;
1159
1160 ret = omap_i2c_transmit_data(omap, num_bytes, true);
1161 if (ret < 0)
1162 break;
1163
1164 omap_i2c_ack_stat(omap, OMAP_I2C_STAT_XDR);
1165 continue;
1166 }
1167
1168 if (stat & OMAP_I2C_STAT_XRDY) {
1169 u8 num_bytes = 1;
1170 int ret;
1171
1172 if (omap->threshold)
1173 num_bytes = omap->threshold;
1174
1175 ret = omap_i2c_transmit_data(omap, num_bytes, false);
1176 if (ret < 0)
1177 break;
1178
1179 omap_i2c_ack_stat(omap, OMAP_I2C_STAT_XRDY);
1180 continue;
1181 }
1182
1183 if (stat & OMAP_I2C_STAT_ROVR) {
1184 dev_err(omap->dev, "Receive overrun\n");
1185 err |= OMAP_I2C_STAT_ROVR;
1186 omap_i2c_ack_stat(omap, OMAP_I2C_STAT_ROVR);
1187 break;
1188 }
1189
1190 if (stat & OMAP_I2C_STAT_XUDF) {
1191 dev_err(omap->dev, "Transmit underflow\n");
1192 err |= OMAP_I2C_STAT_XUDF;
1193 omap_i2c_ack_stat(omap, OMAP_I2C_STAT_XUDF);
1194 break;
1195 }
1196 } while (stat);
1197
1198 return err;
1199 }
1200
1201 static irqreturn_t
1202 omap_i2c_isr_thread(int this_irq, void *dev_id)
1203 {
1204 int ret;
1205 struct omap_i2c_dev *omap = dev_id;
1206
1207 ret = omap_i2c_xfer_data(omap);
1208 if (ret != -EAGAIN)
1209 omap_i2c_complete_cmd(omap, ret);
1210
1211 return IRQ_HANDLED;
1212 }
1213
1214 static const struct i2c_algorithm omap_i2c_algo = {
1215 .master_xfer = omap_i2c_xfer_irq,
1216 .master_xfer_atomic = omap_i2c_xfer_polling,
1217 .functionality = omap_i2c_func,
1218 };
1219
1220 static const struct i2c_adapter_quirks omap_i2c_quirks = {
1221 .flags = I2C_AQ_NO_ZERO_LEN,
1222 };
1223
1224 #ifdef CONFIG_OF
1225 static struct omap_i2c_bus_platform_data omap2420_pdata = {
1226 .rev = OMAP_I2C_IP_VERSION_1,
1227 .flags = OMAP_I2C_FLAG_NO_FIFO |
1228 OMAP_I2C_FLAG_SIMPLE_CLOCK |
1229 OMAP_I2C_FLAG_16BIT_DATA_REG |
1230 OMAP_I2C_FLAG_BUS_SHIFT_2,
1231 };
1232
1233 static struct omap_i2c_bus_platform_data omap2430_pdata = {
1234 .rev = OMAP_I2C_IP_VERSION_1,
1235 .flags = OMAP_I2C_FLAG_BUS_SHIFT_2 |
1236 OMAP_I2C_FLAG_FORCE_19200_INT_CLK,
1237 };
1238
1239 static struct omap_i2c_bus_platform_data omap3_pdata = {
1240 .rev = OMAP_I2C_IP_VERSION_1,
1241 .flags = OMAP_I2C_FLAG_BUS_SHIFT_2,
1242 };
1243
1244 static struct omap_i2c_bus_platform_data omap4_pdata = {
1245 .rev = OMAP_I2C_IP_VERSION_2,
1246 };
1247
1248 static const struct of_device_id omap_i2c_of_match[] = {
1249 {
1250 .compatible = "ti,omap4-i2c",
1251 .data = &omap4_pdata,
1252 },
1253 {
1254 .compatible = "ti,omap3-i2c",
1255 .data = &omap3_pdata,
1256 },
1257 {
1258 .compatible = "ti,omap2430-i2c",
1259 .data = &omap2430_pdata,
1260 },
1261 {
1262 .compatible = "ti,omap2420-i2c",
1263 .data = &omap2420_pdata,
1264 },
1265 { },
1266 };
1267 MODULE_DEVICE_TABLE(of, omap_i2c_of_match);
1268 #endif
1269
1270 #define OMAP_I2C_SCHEME(rev) ((rev & 0xc000) >> 14)
1271
1272 #define OMAP_I2C_REV_SCHEME_0_MAJOR(rev) (rev >> 4)
1273 #define OMAP_I2C_REV_SCHEME_0_MINOR(rev) (rev & 0xf)
1274
1275 #define OMAP_I2C_REV_SCHEME_1_MAJOR(rev) ((rev & 0x0700) >> 7)
1276 #define OMAP_I2C_REV_SCHEME_1_MINOR(rev) (rev & 0x1f)
1277 #define OMAP_I2C_SCHEME_0 0
1278 #define OMAP_I2C_SCHEME_1 1
1279
1280 static int omap_i2c_get_scl(struct i2c_adapter *adap)
1281 {
1282 struct omap_i2c_dev *dev = i2c_get_adapdata(adap);
1283 u32 reg;
1284
1285 reg = omap_i2c_read_reg(dev, OMAP_I2C_SYSTEST_REG);
1286
1287 return reg & OMAP_I2C_SYSTEST_SCL_I_FUNC;
1288 }
1289
1290 static int omap_i2c_get_sda(struct i2c_adapter *adap)
1291 {
1292 struct omap_i2c_dev *dev = i2c_get_adapdata(adap);
1293 u32 reg;
1294
1295 reg = omap_i2c_read_reg(dev, OMAP_I2C_SYSTEST_REG);
1296
1297 return reg & OMAP_I2C_SYSTEST_SDA_I_FUNC;
1298 }
1299
1300 static void omap_i2c_set_scl(struct i2c_adapter *adap, int val)
1301 {
1302 struct omap_i2c_dev *dev = i2c_get_adapdata(adap);
1303 u32 reg;
1304
1305 reg = omap_i2c_read_reg(dev, OMAP_I2C_SYSTEST_REG);
1306 if (val)
1307 reg |= OMAP_I2C_SYSTEST_SCL_O;
1308 else
1309 reg &= ~OMAP_I2C_SYSTEST_SCL_O;
1310 omap_i2c_write_reg(dev, OMAP_I2C_SYSTEST_REG, reg);
1311 }
1312
1313 static void omap_i2c_prepare_recovery(struct i2c_adapter *adap)
1314 {
1315 struct omap_i2c_dev *dev = i2c_get_adapdata(adap);
1316 u32 reg;
1317
1318 reg = omap_i2c_read_reg(dev, OMAP_I2C_SYSTEST_REG);
1319 /* enable test mode */
1320 reg |= OMAP_I2C_SYSTEST_ST_EN;
1321 /* select SDA/SCL IO mode */
1322 reg |= 3 << OMAP_I2C_SYSTEST_TMODE_SHIFT;
1323 /* set SCL to high-impedance state (reset value is 0) */
1324 reg |= OMAP_I2C_SYSTEST_SCL_O;
1325 /* set SDA to high-impedance state (reset value is 0) */
1326 reg |= OMAP_I2C_SYSTEST_SDA_O;
1327 omap_i2c_write_reg(dev, OMAP_I2C_SYSTEST_REG, reg);
1328 }
1329
1330 static void omap_i2c_unprepare_recovery(struct i2c_adapter *adap)
1331 {
1332 struct omap_i2c_dev *dev = i2c_get_adapdata(adap);
1333 u32 reg;
1334
1335 reg = omap_i2c_read_reg(dev, OMAP_I2C_SYSTEST_REG);
1336 /* restore reset values */
1337 reg &= ~OMAP_I2C_SYSTEST_ST_EN;
1338 reg &= ~OMAP_I2C_SYSTEST_TMODE_MASK;
1339 reg &= ~OMAP_I2C_SYSTEST_SCL_O;
1340 reg &= ~OMAP_I2C_SYSTEST_SDA_O;
1341 omap_i2c_write_reg(dev, OMAP_I2C_SYSTEST_REG, reg);
1342 }
1343
1344 static struct i2c_bus_recovery_info omap_i2c_bus_recovery_info = {
1345 .get_scl = omap_i2c_get_scl,
1346 .get_sda = omap_i2c_get_sda,
1347 .set_scl = omap_i2c_set_scl,
1348 .prepare_recovery = omap_i2c_prepare_recovery,
1349 .unprepare_recovery = omap_i2c_unprepare_recovery,
1350 .recover_bus = i2c_generic_scl_recovery,
1351 };
1352
1353 static int
1354 omap_i2c_probe(struct platform_device *pdev)
1355 {
1356 struct omap_i2c_dev *omap;
1357 struct i2c_adapter *adap;
1358 struct resource *mem;
1359 const struct omap_i2c_bus_platform_data *pdata =
1360 dev_get_platdata(&pdev->dev);
1361 struct device_node *node = pdev->dev.of_node;
1362 const struct of_device_id *match;
1363 int irq;
1364 int r;
1365 u32 rev;
1366 u16 minor, major;
1367
1368 irq = platform_get_irq(pdev, 0);
1369 if (irq < 0) {
1370 dev_err(&pdev->dev, "no irq resource?\n");
1371 return irq;
1372 }
1373
1374 omap = devm_kzalloc(&pdev->dev, sizeof(struct omap_i2c_dev), GFP_KERNEL);
1375 if (!omap)
1376 return -ENOMEM;
1377
1378 mem = platform_get_resource(pdev, IORESOURCE_MEM, 0);
1379 omap->base = devm_ioremap_resource(&pdev->dev, mem);
1380 if (IS_ERR(omap->base))
1381 return PTR_ERR(omap->base);
1382
1383 match = of_match_device(of_match_ptr(omap_i2c_of_match), &pdev->dev);
1384 if (match) {
1385 u32 freq = 100000; /* default to 100000 Hz */
1386
1387 pdata = match->data;
1388 omap->flags = pdata->flags;
1389
1390 of_property_read_u32(node, "clock-frequency", &freq);
1391 /* convert DT freq value in Hz into kHz for speed */
1392 omap->speed = freq / 1000;
1393 } else if (pdata != NULL) {
1394 omap->speed = pdata->clkrate;
1395 omap->flags = pdata->flags;
1396 omap->set_mpu_wkup_lat = pdata->set_mpu_wkup_lat;
1397 }
1398
1399 omap->dev = &pdev->dev;
1400 omap->irq = irq;
1401
1402 platform_set_drvdata(pdev, omap);
1403 init_completion(&omap->cmd_complete);
1404
1405 omap->reg_shift = (omap->flags >> OMAP_I2C_FLAG_BUS_SHIFT__SHIFT) & 3;
1406
1407 pm_runtime_enable(omap->dev);
1408 pm_runtime_set_autosuspend_delay(omap->dev, OMAP_I2C_PM_TIMEOUT);
1409 pm_runtime_use_autosuspend(omap->dev);
1410
1411 r = pm_runtime_get_sync(omap->dev);
1412 if (r < 0)
1413 goto err_free_mem;
1414
1415 /*
1416 * Read the Rev hi bit-[15:14] ie scheme this is 1 indicates ver2.
1417 * On omap1/3/2 Offset 4 is IE Reg the bit [15:14] is 0 at reset.
1418 * Also since the omap_i2c_read_reg uses reg_map_ip_* a
1419 * readw_relaxed is done.
1420 */
1421 rev = readw_relaxed(omap->base + 0x04);
1422
1423 omap->scheme = OMAP_I2C_SCHEME(rev);
1424 switch (omap->scheme) {
1425 case OMAP_I2C_SCHEME_0:
1426 omap->regs = (u8 *)reg_map_ip_v1;
1427 omap->rev = omap_i2c_read_reg(omap, OMAP_I2C_REV_REG);
1428 minor = OMAP_I2C_REV_SCHEME_0_MAJOR(omap->rev);
1429 major = OMAP_I2C_REV_SCHEME_0_MAJOR(omap->rev);
1430 break;
1431 case OMAP_I2C_SCHEME_1:
1432 /* FALLTHROUGH */
1433 default:
1434 omap->regs = (u8 *)reg_map_ip_v2;
1435 rev = (rev << 16) |
1436 omap_i2c_read_reg(omap, OMAP_I2C_IP_V2_REVNB_LO);
1437 minor = OMAP_I2C_REV_SCHEME_1_MINOR(rev);
1438 major = OMAP_I2C_REV_SCHEME_1_MAJOR(rev);
1439 omap->rev = rev;
1440 }
1441
1442 omap->errata = 0;
1443
1444 if (omap->rev >= OMAP_I2C_REV_ON_2430 &&
1445 omap->rev < OMAP_I2C_REV_ON_4430_PLUS)
1446 omap->errata |= I2C_OMAP_ERRATA_I207;
1447
1448 if (omap->rev <= OMAP_I2C_REV_ON_3430_3530)
1449 omap->errata |= I2C_OMAP_ERRATA_I462;
1450
1451 if (!(omap->flags & OMAP_I2C_FLAG_NO_FIFO)) {
1452 u16 s;
1453
1454 /* Set up the fifo size - Get total size */
1455 s = (omap_i2c_read_reg(omap, OMAP_I2C_BUFSTAT_REG) >> 14) & 0x3;
1456 omap->fifo_size = 0x8 << s;
1457
1458 /*
1459 * Set up notification threshold as half the total available
1460 * size. This is to ensure that we can handle the status on int
1461 * call back latencies.
1462 */
1463
1464 omap->fifo_size = (omap->fifo_size / 2);
1465
1466 if (omap->rev < OMAP_I2C_REV_ON_3630)
1467 omap->b_hw = 1; /* Enable hardware fixes */
1468
1469 /* calculate wakeup latency constraint for MPU */
1470 if (omap->set_mpu_wkup_lat != NULL)
1471 omap->latency = (1000000 * omap->fifo_size) /
1472 (1000 * omap->speed / 8);
1473 }
1474
1475 /* reset ASAP, clearing any IRQs */
1476 omap_i2c_init(omap);
1477
1478 if (omap->rev < OMAP_I2C_OMAP1_REV_2)
1479 r = devm_request_irq(&pdev->dev, omap->irq, omap_i2c_omap1_isr,
1480 IRQF_NO_SUSPEND, pdev->name, omap);
1481 else
1482 r = devm_request_threaded_irq(&pdev->dev, omap->irq,
1483 omap_i2c_isr, omap_i2c_isr_thread,
1484 IRQF_NO_SUSPEND | IRQF_ONESHOT,
1485 pdev->name, omap);
1486
1487 if (r) {
1488 dev_err(omap->dev, "failure requesting irq %i\n", omap->irq);
1489 goto err_unuse_clocks;
1490 }
1491
1492 adap = &omap->adapter;
1493 i2c_set_adapdata(adap, omap);
1494 adap->owner = THIS_MODULE;
1495 adap->class = I2C_CLASS_DEPRECATED;
1496 strlcpy(adap->name, "OMAP I2C adapter", sizeof(adap->name));
1497 adap->algo = &omap_i2c_algo;
1498 adap->quirks = &omap_i2c_quirks;
1499 adap->dev.parent = &pdev->dev;
1500 adap->dev.of_node = pdev->dev.of_node;
1501 adap->bus_recovery_info = &omap_i2c_bus_recovery_info;
1502
1503 /* i2c device drivers may be active on return from add_adapter() */
1504 adap->nr = pdev->id;
1505 r = i2c_add_numbered_adapter(adap);
1506 if (r)
1507 goto err_unuse_clocks;
1508
1509 dev_info(omap->dev, "bus %d rev%d.%d at %d kHz\n", adap->nr,
1510 major, minor, omap->speed);
1511
1512 pm_runtime_mark_last_busy(omap->dev);
1513 pm_runtime_put_autosuspend(omap->dev);
1514
1515 return 0;
1516
1517 err_unuse_clocks:
1518 omap_i2c_write_reg(omap, OMAP_I2C_CON_REG, 0);
1519 pm_runtime_dont_use_autosuspend(omap->dev);
1520 pm_runtime_put_sync(omap->dev);
1521 pm_runtime_disable(&pdev->dev);
1522 err_free_mem:
1523
1524 return r;
1525 }
1526
1527 static int omap_i2c_remove(struct platform_device *pdev)
1528 {
1529 struct omap_i2c_dev *omap = platform_get_drvdata(pdev);
1530 int ret;
1531
1532 i2c_del_adapter(&omap->adapter);
1533 ret = pm_runtime_get_sync(&pdev->dev);
1534 if (ret < 0)
1535 return ret;
1536
1537 omap_i2c_write_reg(omap, OMAP_I2C_CON_REG, 0);
1538 pm_runtime_dont_use_autosuspend(&pdev->dev);
1539 pm_runtime_put_sync(&pdev->dev);
1540 pm_runtime_disable(&pdev->dev);
1541 return 0;
1542 }
1543
1544 static int __maybe_unused omap_i2c_runtime_suspend(struct device *dev)
1545 {
1546 struct omap_i2c_dev *omap = dev_get_drvdata(dev);
1547
1548 omap->iestate = omap_i2c_read_reg(omap, OMAP_I2C_IE_REG);
1549
1550 if (omap->scheme == OMAP_I2C_SCHEME_0)
1551 omap_i2c_write_reg(omap, OMAP_I2C_IE_REG, 0);
1552 else
1553 omap_i2c_write_reg(omap, OMAP_I2C_IP_V2_IRQENABLE_CLR,
1554 OMAP_I2C_IP_V2_INTERRUPTS_MASK);
1555
1556 if (omap->rev < OMAP_I2C_OMAP1_REV_2) {
1557 omap_i2c_read_reg(omap, OMAP_I2C_IV_REG); /* Read clears */
1558 } else {
1559 omap_i2c_write_reg(omap, OMAP_I2C_STAT_REG, omap->iestate);
1560
1561 /* Flush posted write */
1562 omap_i2c_read_reg(omap, OMAP_I2C_STAT_REG);
1563 }
1564
1565 pinctrl_pm_select_sleep_state(dev);
1566
1567 return 0;
1568 }
1569
1570 static int __maybe_unused omap_i2c_runtime_resume(struct device *dev)
1571 {
1572 struct omap_i2c_dev *omap = dev_get_drvdata(dev);
1573
1574 pinctrl_pm_select_default_state(dev);
1575
1576 if (!omap->regs)
1577 return 0;
1578
1579 __omap_i2c_init(omap);
1580
1581 return 0;
1582 }
1583
1584 static const struct dev_pm_ops omap_i2c_pm_ops = {
1585 SET_NOIRQ_SYSTEM_SLEEP_PM_OPS(pm_runtime_force_suspend,
1586 pm_runtime_force_resume)
1587 SET_RUNTIME_PM_OPS(omap_i2c_runtime_suspend,
1588 omap_i2c_runtime_resume, NULL)
1589 };
1590
1591 static struct platform_driver omap_i2c_driver = {
1592 .probe = omap_i2c_probe,
1593 .remove = omap_i2c_remove,
1594 .driver = {
1595 .name = "omap_i2c",
1596 .pm = &omap_i2c_pm_ops,
1597 .of_match_table = of_match_ptr(omap_i2c_of_match),
1598 },
1599 };
1600
1601 /* I2C may be needed to bring up other drivers */
1602 static int __init
1603 omap_i2c_init_driver(void)
1604 {
1605 return platform_driver_register(&omap_i2c_driver);
1606 }
1607 subsys_initcall(omap_i2c_init_driver);
1608
1609 static void __exit omap_i2c_exit_driver(void)
1610 {
1611 platform_driver_unregister(&omap_i2c_driver);
1612 }
1613 module_exit(omap_i2c_exit_driver);
1614
1615 MODULE_AUTHOR("MontaVista Software, Inc. (and others)");
1616 MODULE_DESCRIPTION("TI OMAP I2C bus adapter");
1617 MODULE_LICENSE("GPL");
1618 MODULE_ALIAS("platform:omap_i2c");
Linux with added FPC-III support