treewide: remove redundant IS_ERR() before error code check
[linux/fpc-iii.git] / drivers / net / phy / dp83640_reg.h
blob21aa24c741b9671222e1baa63c92177b0ffa72d6
1 /* SPDX-License-Identifier: GPL-2.0 */
2 /* dp83640_reg.h
3 * Generated by regen.tcl on Thu Feb 17 10:02:48 AM CET 2011
4 */
5 #ifndef HAVE_DP83640_REGISTERS
6 #define HAVE_DP83640_REGISTERS
8 #define PAGE0 0x0000
9 #define PHYCR2 0x001c /* PHY Control Register 2 */
11 #define PAGE4 0x0004
12 #define PTP_CTL 0x0014 /* PTP Control Register */
13 #define PTP_TDR 0x0015 /* PTP Time Data Register */
14 #define PTP_STS 0x0016 /* PTP Status Register */
15 #define PTP_TSTS 0x0017 /* PTP Trigger Status Register */
16 #define PTP_RATEL 0x0018 /* PTP Rate Low Register */
17 #define PTP_RATEH 0x0019 /* PTP Rate High Register */
18 #define PTP_RDCKSUM 0x001a /* PTP Read Checksum */
19 #define PTP_WRCKSUM 0x001b /* PTP Write Checksum */
20 #define PTP_TXTS 0x001c /* PTP Transmit Timestamp Register, in four 16-bit reads */
21 #define PTP_RXTS 0x001d /* PTP Receive Timestamp Register, in six? 16-bit reads */
22 #define PTP_ESTS 0x001e /* PTP Event Status Register */
23 #define PTP_EDATA 0x001f /* PTP Event Data Register */
25 #define PAGE5 0x0005
26 #define PTP_TRIG 0x0014 /* PTP Trigger Configuration Register */
27 #define PTP_EVNT 0x0015 /* PTP Event Configuration Register */
28 #define PTP_TXCFG0 0x0016 /* PTP Transmit Configuration Register 0 */
29 #define PTP_TXCFG1 0x0017 /* PTP Transmit Configuration Register 1 */
30 #define PSF_CFG0 0x0018 /* PHY Status Frame Configuration Register 0 */
31 #define PTP_RXCFG0 0x0019 /* PTP Receive Configuration Register 0 */
32 #define PTP_RXCFG1 0x001a /* PTP Receive Configuration Register 1 */
33 #define PTP_RXCFG2 0x001b /* PTP Receive Configuration Register 2 */
34 #define PTP_RXCFG3 0x001c /* PTP Receive Configuration Register 3 */
35 #define PTP_RXCFG4 0x001d /* PTP Receive Configuration Register 4 */
36 #define PTP_TRDL 0x001e /* PTP Temporary Rate Duration Low Register */
37 #define PTP_TRDH 0x001f /* PTP Temporary Rate Duration High Register */
39 #define PAGE6 0x0006
40 #define PTP_COC 0x0014 /* PTP Clock Output Control Register */
41 #define PSF_CFG1 0x0015 /* PHY Status Frame Configuration Register 1 */
42 #define PSF_CFG2 0x0016 /* PHY Status Frame Configuration Register 2 */
43 #define PSF_CFG3 0x0017 /* PHY Status Frame Configuration Register 3 */
44 #define PSF_CFG4 0x0018 /* PHY Status Frame Configuration Register 4 */
45 #define PTP_SFDCFG 0x0019 /* PTP SFD Configuration Register */
46 #define PTP_INTCTL 0x001a /* PTP Interrupt Control Register */
47 #define PTP_CLKSRC 0x001b /* PTP Clock Source Register */
48 #define PTP_ETR 0x001c /* PTP Ethernet Type Register */
49 #define PTP_OFF 0x001d /* PTP Offset Register */
50 #define PTP_GPIOMON 0x001e /* PTP GPIO Monitor Register */
51 #define PTP_RXHASH 0x001f /* PTP Receive Hash Register */
53 /* Bit definitions for the PHYCR2 register */
54 #define BC_WRITE (1<<11) /* Broadcast Write Enable */
56 /* Bit definitions for the PTP_CTL register */
57 #define TRIG_SEL_SHIFT (10) /* PTP Trigger Select */
58 #define TRIG_SEL_MASK (0x7)
59 #define TRIG_DIS (1<<9) /* Disable PTP Trigger */
60 #define TRIG_EN (1<<8) /* Enable PTP Trigger */
61 #define TRIG_READ (1<<7) /* Read PTP Trigger */
62 #define TRIG_LOAD (1<<6) /* Load PTP Trigger */
63 #define PTP_RD_CLK (1<<5) /* Read PTP Clock */
64 #define PTP_LOAD_CLK (1<<4) /* Load PTP Clock */
65 #define PTP_STEP_CLK (1<<3) /* Step PTP Clock */
66 #define PTP_ENABLE (1<<2) /* Enable PTP Clock */
67 #define PTP_DISABLE (1<<1) /* Disable PTP Clock */
68 #define PTP_RESET (1<<0) /* Reset PTP Clock */
70 /* Bit definitions for the PTP_STS register */
71 #define TXTS_RDY (1<<11) /* Transmit Timestamp Ready */
72 #define RXTS_RDY (1<<10) /* Receive Timestamp Ready */
73 #define TRIG_DONE (1<<9) /* PTP Trigger Done */
74 #define EVENT_RDY (1<<8) /* PTP Event Timestamp Ready */
75 #define TXTS_IE (1<<3) /* Transmit Timestamp Interrupt Enable */
76 #define RXTS_IE (1<<2) /* Receive Timestamp Interrupt Enable */
77 #define TRIG_IE (1<<1) /* Trigger Interrupt Enable */
78 #define EVENT_IE (1<<0) /* Event Interrupt Enable */
80 /* Bit definitions for the PTP_TSTS register */
81 #define TRIG7_ERROR (1<<15) /* Trigger 7 Error */
82 #define TRIG7_ACTIVE (1<<14) /* Trigger 7 Active */
83 #define TRIG6_ERROR (1<<13) /* Trigger 6 Error */
84 #define TRIG6_ACTIVE (1<<12) /* Trigger 6 Active */
85 #define TRIG5_ERROR (1<<11) /* Trigger 5 Error */
86 #define TRIG5_ACTIVE (1<<10) /* Trigger 5 Active */
87 #define TRIG4_ERROR (1<<9) /* Trigger 4 Error */
88 #define TRIG4_ACTIVE (1<<8) /* Trigger 4 Active */
89 #define TRIG3_ERROR (1<<7) /* Trigger 3 Error */
90 #define TRIG3_ACTIVE (1<<6) /* Trigger 3 Active */
91 #define TRIG2_ERROR (1<<5) /* Trigger 2 Error */
92 #define TRIG2_ACTIVE (1<<4) /* Trigger 2 Active */
93 #define TRIG1_ERROR (1<<3) /* Trigger 1 Error */
94 #define TRIG1_ACTIVE (1<<2) /* Trigger 1 Active */
95 #define TRIG0_ERROR (1<<1) /* Trigger 0 Error */
96 #define TRIG0_ACTIVE (1<<0) /* Trigger 0 Active */
98 /* Bit definitions for the PTP_RATEH register */
99 #define PTP_RATE_DIR (1<<15) /* PTP Rate Direction */
100 #define PTP_TMP_RATE (1<<14) /* PTP Temporary Rate */
101 #define PTP_RATE_HI_SHIFT (0) /* PTP Rate High 10-bits */
102 #define PTP_RATE_HI_MASK (0x3ff)
104 /* Bit definitions for the PTP_ESTS register */
105 #define EVNTS_MISSED_SHIFT (8) /* Indicates number of events missed */
106 #define EVNTS_MISSED_MASK (0x7)
107 #define EVNT_TS_LEN_SHIFT (6) /* Indicates length of the Timestamp field in 16-bit words minus 1 */
108 #define EVNT_TS_LEN_MASK (0x3)
109 #define EVNT_RF (1<<5) /* Indicates whether the event is a rise or falling event */
110 #define EVNT_NUM_SHIFT (2) /* Indicates Event Timestamp Unit which detected an event */
111 #define EVNT_NUM_MASK (0x7)
112 #define MULT_EVNT (1<<1) /* Indicates multiple events were detected at the same time */
113 #define EVENT_DET (1<<0) /* PTP Event Detected */
115 /* Bit definitions for the PTP_EDATA register */
116 #define E7_RISE (1<<15) /* Indicates direction of Event 7 */
117 #define E7_DET (1<<14) /* Indicates Event 7 detected */
118 #define E6_RISE (1<<13) /* Indicates direction of Event 6 */
119 #define E6_DET (1<<12) /* Indicates Event 6 detected */
120 #define E5_RISE (1<<11) /* Indicates direction of Event 5 */
121 #define E5_DET (1<<10) /* Indicates Event 5 detected */
122 #define E4_RISE (1<<9) /* Indicates direction of Event 4 */
123 #define E4_DET (1<<8) /* Indicates Event 4 detected */
124 #define E3_RISE (1<<7) /* Indicates direction of Event 3 */
125 #define E3_DET (1<<6) /* Indicates Event 3 detected */
126 #define E2_RISE (1<<5) /* Indicates direction of Event 2 */
127 #define E2_DET (1<<4) /* Indicates Event 2 detected */
128 #define E1_RISE (1<<3) /* Indicates direction of Event 1 */
129 #define E1_DET (1<<2) /* Indicates Event 1 detected */
130 #define E0_RISE (1<<1) /* Indicates direction of Event 0 */
131 #define E0_DET (1<<0) /* Indicates Event 0 detected */
133 /* Bit definitions for the PTP_TRIG register */
134 #define TRIG_PULSE (1<<15) /* generate a Pulse rather than a single edge */
135 #define TRIG_PER (1<<14) /* generate a periodic signal */
136 #define TRIG_IF_LATE (1<<13) /* trigger immediately if already past */
137 #define TRIG_NOTIFY (1<<12) /* Trigger Notification Enable */
138 #define TRIG_GPIO_SHIFT (8) /* Trigger GPIO Connection, value 1-12 */
139 #define TRIG_GPIO_MASK (0xf)
140 #define TRIG_TOGGLE (1<<7) /* Trigger Toggle Mode Enable */
141 #define TRIG_CSEL_SHIFT (1) /* Trigger Configuration Select */
142 #define TRIG_CSEL_MASK (0x7)
143 #define TRIG_WR (1<<0) /* Trigger Configuration Write */
145 /* Bit definitions for the PTP_EVNT register */
146 #define EVNT_RISE (1<<14) /* Event Rise Detect Enable */
147 #define EVNT_FALL (1<<13) /* Event Fall Detect Enable */
148 #define EVNT_SINGLE (1<<12) /* enable single event capture operation */
149 #define EVNT_GPIO_SHIFT (8) /* Event GPIO Connection, value 1-12 */
150 #define EVNT_GPIO_MASK (0xf)
151 #define EVNT_SEL_SHIFT (1) /* Event Select */
152 #define EVNT_SEL_MASK (0x7)
153 #define EVNT_WR (1<<0) /* Event Configuration Write */
155 /* Bit definitions for the PTP_TXCFG0 register */
156 #define SYNC_1STEP (1<<15) /* insert timestamp into transmit Sync Messages */
157 #define DR_INSERT (1<<13) /* Insert Delay_Req Timestamp in Delay_Resp (dangerous) */
158 #define NTP_TS_EN (1<<12) /* Enable Timestamping of NTP Packets */
159 #define IGNORE_2STEP (1<<11) /* Ignore Two_Step flag for One-Step operation */
160 #define CRC_1STEP (1<<10) /* Disable checking of CRC for One-Step operation */
161 #define CHK_1STEP (1<<9) /* Enable UDP Checksum correction for One-Step Operation */
162 #define IP1588_EN (1<<8) /* Enable IEEE 1588 defined IP address filter */
163 #define TX_L2_EN (1<<7) /* Layer2 Timestamp Enable */
164 #define TX_IPV6_EN (1<<6) /* IPv6 Timestamp Enable */
165 #define TX_IPV4_EN (1<<5) /* IPv4 Timestamp Enable */
166 #define TX_PTP_VER_SHIFT (1) /* Enable Timestamp capture for IEEE 1588 version X */
167 #define TX_PTP_VER_MASK (0xf)
168 #define TX_TS_EN (1<<0) /* Transmit Timestamp Enable */
170 /* Bit definitions for the PTP_TXCFG1 register */
171 #define BYTE0_MASK_SHIFT (8) /* Bit mask to be used for matching Byte0 of the PTP Message */
172 #define BYTE0_MASK_MASK (0xff)
173 #define BYTE0_DATA_SHIFT (0) /* Data to be used for matching Byte0 of the PTP Message */
174 #define BYTE0_DATA_MASK (0xff)
176 /* Bit definitions for the PSF_CFG0 register */
177 #define MAC_SRC_ADD_SHIFT (11) /* Status Frame Mac Source Address */
178 #define MAC_SRC_ADD_MASK (0x3)
179 #define MIN_PRE_SHIFT (8) /* Status Frame Minimum Preamble */
180 #define MIN_PRE_MASK (0x7)
181 #define PSF_ENDIAN (1<<7) /* Status Frame Endian Control */
182 #define PSF_IPV4 (1<<6) /* Status Frame IPv4 Enable */
183 #define PSF_PCF_RD (1<<5) /* Control Frame Read PHY Status Frame Enable */
184 #define PSF_ERR_EN (1<<4) /* Error PHY Status Frame Enable */
185 #define PSF_TXTS_EN (1<<3) /* Transmit Timestamp PHY Status Frame Enable */
186 #define PSF_RXTS_EN (1<<2) /* Receive Timestamp PHY Status Frame Enable */
187 #define PSF_TRIG_EN (1<<1) /* Trigger PHY Status Frame Enable */
188 #define PSF_EVNT_EN (1<<0) /* Event PHY Status Frame Enable */
190 /* Bit definitions for the PTP_RXCFG0 register */
191 #define DOMAIN_EN (1<<15) /* Domain Match Enable */
192 #define ALT_MAST_DIS (1<<14) /* Alternate Master Timestamp Disable */
193 #define USER_IP_SEL (1<<13) /* Selects portion of IP address accessible thru PTP_RXCFG2 */
194 #define USER_IP_EN (1<<12) /* Enable User-programmed IP address filter */
195 #define RX_SLAVE (1<<11) /* Receive Slave Only */
196 #define IP1588_EN_SHIFT (8) /* Enable IEEE 1588 defined IP address filters */
197 #define IP1588_EN_MASK (0xf)
198 #define RX_L2_EN (1<<7) /* Layer2 Timestamp Enable */
199 #define RX_IPV6_EN (1<<6) /* IPv6 Timestamp Enable */
200 #define RX_IPV4_EN (1<<5) /* IPv4 Timestamp Enable */
201 #define RX_PTP_VER_SHIFT (1) /* Enable Timestamp capture for IEEE 1588 version X */
202 #define RX_PTP_VER_MASK (0xf)
203 #define RX_TS_EN (1<<0) /* Receive Timestamp Enable */
205 /* Bit definitions for the PTP_RXCFG1 register */
206 #define BYTE0_MASK_SHIFT (8) /* Bit mask to be used for matching Byte0 of the PTP Message */
207 #define BYTE0_MASK_MASK (0xff)
208 #define BYTE0_DATA_SHIFT (0) /* Data to be used for matching Byte0 of the PTP Message */
209 #define BYTE0_DATA_MASK (0xff)
211 /* Bit definitions for the PTP_RXCFG3 register */
212 #define TS_MIN_IFG_SHIFT (12) /* Minimum Inter-frame Gap */
213 #define TS_MIN_IFG_MASK (0xf)
214 #define ACC_UDP (1<<11) /* Record Timestamp if UDP Checksum Error */
215 #define ACC_CRC (1<<10) /* Record Timestamp if CRC Error */
216 #define TS_APPEND (1<<9) /* Append Timestamp for L2 */
217 #define TS_INSERT (1<<8) /* Enable Timestamp Insertion */
218 #define PTP_DOMAIN_SHIFT (0) /* PTP Message domainNumber field */
219 #define PTP_DOMAIN_MASK (0xff)
221 /* Bit definitions for the PTP_RXCFG4 register */
222 #define IPV4_UDP_MOD (1<<15) /* Enable IPV4 UDP Modification */
223 #define TS_SEC_EN (1<<14) /* Enable Timestamp Seconds */
224 #define TS_SEC_LEN_SHIFT (12) /* Inserted Timestamp Seconds Length */
225 #define TS_SEC_LEN_MASK (0x3)
226 #define RXTS_NS_OFF_SHIFT (6) /* Receive Timestamp Nanoseconds offset */
227 #define RXTS_NS_OFF_MASK (0x3f)
228 #define RXTS_SEC_OFF_SHIFT (0) /* Receive Timestamp Seconds offset */
229 #define RXTS_SEC_OFF_MASK (0x3f)
231 /* Bit definitions for the PTP_COC register */
232 #define PTP_CLKOUT_EN (1<<15) /* PTP Clock Output Enable */
233 #define PTP_CLKOUT_SEL (1<<14) /* PTP Clock Output Source Select */
234 #define PTP_CLKOUT_SPEEDSEL (1<<13) /* PTP Clock Output I/O Speed Select */
235 #define PTP_CLKDIV_SHIFT (0) /* PTP Clock Divide-by Value */
236 #define PTP_CLKDIV_MASK (0xff)
238 /* Bit definitions for the PSF_CFG1 register */
239 #define PTPRESERVED_SHIFT (12) /* PTP v2 reserved field */
240 #define PTPRESERVED_MASK (0xf)
241 #define VERSIONPTP_SHIFT (8) /* PTP v2 versionPTP field */
242 #define VERSIONPTP_MASK (0xf)
243 #define TRANSPORT_SPECIFIC_SHIFT (4) /* PTP v2 Header transportSpecific field */
244 #define TRANSPORT_SPECIFIC_MASK (0xf)
245 #define MESSAGETYPE_SHIFT (0) /* PTP v2 messageType field */
246 #define MESSAGETYPE_MASK (0xf)
248 /* Bit definitions for the PTP_SFDCFG register */
249 #define TX_SFD_GPIO_SHIFT (4) /* TX SFD GPIO Select, value 1-12 */
250 #define TX_SFD_GPIO_MASK (0xf)
251 #define RX_SFD_GPIO_SHIFT (0) /* RX SFD GPIO Select, value 1-12 */
252 #define RX_SFD_GPIO_MASK (0xf)
254 /* Bit definitions for the PTP_INTCTL register */
255 #define PTP_INT_GPIO_SHIFT (0) /* PTP Interrupt GPIO Select */
256 #define PTP_INT_GPIO_MASK (0xf)
258 /* Bit definitions for the PTP_CLKSRC register */
259 #define CLK_SRC_SHIFT (14) /* PTP Clock Source Select */
260 #define CLK_SRC_MASK (0x3)
261 #define CLK_SRC_PER_SHIFT (0) /* PTP Clock Source Period */
262 #define CLK_SRC_PER_MASK (0x7f)
264 /* Bit definitions for the PTP_OFF register */
265 #define PTP_OFFSET_SHIFT (0) /* PTP Message offset from preceding header */
266 #define PTP_OFFSET_MASK (0xff)
268 #endif