?  search:
summary | log | graphiclog1 | graphiclog2 | commit | commitdiff | tree | refs | edit | fork
blame | history | raw | HEAD
treewide: remove redundant IS_ERR() before error code check
[linux/fpc-iii.git] / drivers / net / wireless / realtek / rtlwifi / rtl8192ee / pwrseq.h
blob2ae8347f7ebb89bb99c93e3fc508a6edafebb4c2
1 /* SPDX-License-Identifier: GPL-2.0 */
2 /* Copyright(c) 2009-2014 Realtek Corporation.*/
3
4 #ifndef __RTL92E_PWRSEQ_H__
5 #define __RTL92E_PWRSEQ_H__
6
7 #include "../pwrseqcmd.h"
8 /**
9 * Check document WM-20110607-Paul-RTL8192E_Power_Architecture-R02.vsd
10 * There are 6 HW Power States:
11 * 0: POFF--Power Off
12 * 1: PDN--Power Down
13 * 2: CARDEMU--Card Emulation
14 * 3: ACT--Active Mode
15 * 4: LPS--Low Power State
16 * 5: SUS--Suspend
17 *
18 * The transision from different states are defined below
19 * TRANS_CARDEMU_TO_ACT
20 * TRANS_ACT_TO_CARDEMU
21 * TRANS_CARDEMU_TO_SUS
22 * TRANS_SUS_TO_CARDEMU
23 * TRANS_CARDEMU_TO_PDN
24 * TRANS_ACT_TO_LPS
25 * TRANS_LPS_TO_ACT
26 *
27 * TRANS_END
28 * PWR SEQ Version: rtl8192E_PwrSeq_V09.h
29 */
30
31 #define RTL8192E_TRANS_CARDEMU_TO_ACT_STEPS 18
32 #define RTL8192E_TRANS_ACT_TO_CARDEMU_STEPS 18
33 #define RTL8192E_TRANS_CARDEMU_TO_SUS_STEPS 18
34 #define RTL8192E_TRANS_SUS_TO_CARDEMU_STEPS 18
35 #define RTL8192E_TRANS_CARDEMU_TO_PDN_STEPS 18
36 #define RTL8192E_TRANS_PDN_TO_CARDEMU_STEPS 18
37 #define RTL8192E_TRANS_ACT_TO_LPS_STEPS 23
38 #define RTL8192E_TRANS_LPS_TO_ACT_STEPS 23
39 #define RTL8192E_TRANS_END_STEPS 1
40
41 #define RTL8192E_TRANS_CARDEMU_TO_ACT \
42 /* format */ \
43 /* comments here */ \
44 /* { offset, cut_msk, fab_msk|interface_msk, base|cmd, msk, value },*/\
45 /* disable HWPDN 0x04[15]=0*/ \
46 {0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, \
47 PWR_BASEADDR_MAC , PWR_CMD_WRITE, BIT(7), 0}, \
48 /* disable SW LPS 0x04[10]=0*/ \
49 {0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, \
50 PWR_BASEADDR_MAC , PWR_CMD_WRITE, BIT(2), 0}, \
51 /* disable WL suspend*/ \
52 {0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, \
53 PWR_BASEADDR_MAC , PWR_CMD_WRITE, (BIT(4)|BIT(3)), 0}, \
54 /* wait till 0x04[17] = 1 power ready*/ \
55 {0x0006, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, \
56 PWR_BASEADDR_MAC , PWR_CMD_POLLING, BIT(1), BIT(1)}, \
57 /* release WLON reset 0x04[16]=1*/ \
58 {0x0006, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, \
59 PWR_BASEADDR_MAC , PWR_CMD_WRITE, BIT(0), BIT(0)}, \
60 /* polling until return 0*/ \
61 {0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, \
62 PWR_BASEADDR_MAC , PWR_CMD_WRITE, BIT(0), BIT(0)}, \
63 /**/ \
64 {0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, \
65 PWR_BASEADDR_MAC , PWR_CMD_POLLING, BIT(0), 0},
66
67 #define RTL8192E_TRANS_ACT_TO_CARDEMU \
68 /* format */ \
69 /* comments here */ \
70 /* { offset, cut_msk, fab_msk|interface_msk, base|cmd, msk, value },*/\
71 /*0x1F[7:0] = 0 turn off RF*/ \
72 {0x001F, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, \
73 PWR_BASEADDR_MAC , PWR_CMD_WRITE, 0xFF, 0}, \
74 /*0x4C[23]=0x4E[7]=0, switch DPDT_SEL_P output from register 0x65[2] */\
75 {0x004E, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, \
76 PWR_BASEADDR_MAC , PWR_CMD_WRITE, BIT(7), 0}, \
77 /*0x04[9] = 1 turn off MAC by HW state machine*/ \
78 {0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, \
79 PWR_BASEADDR_MAC , PWR_CMD_WRITE, BIT(1), BIT(1)}, \
80 /*wait till 0x04[9] = 0 polling until return 0 to disable*/ \
81 {0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, \
82 PWR_BASEADDR_MAC , PWR_CMD_POLLING, BIT(1), 0},
83
84 #define RTL8192E_TRANS_CARDEMU_TO_SUS \
85 /* format */ \
86 /* comments here */ \
87 /* { offset, cut_msk, fab_msk|interface_msk, base|cmd, msk, value },*/\
88 /*0x04[12:11] = 2b'11 enable WL suspend for PCIe*/ \
89 {0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_PCI_MSK, \
90 PWR_BASEADDR_MAC , PWR_CMD_WRITE, BIT(4) | BIT(3), (BIT(4) | BIT(3))},\
91 /*0x04[12:11] = 2b'01 enable WL suspend*/ \
92 {0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, \
93 PWR_INTF_USB_MSK | PWR_INTF_SDIO_MSK, PWR_BASEADDR_MAC, \
94 PWR_CMD_WRITE, BIT(3)|BIT(4), BIT(3)}, \
95 /*0x04[12:11] = 2b'11 enable WL suspend for PCIe*/ \
96 {0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_PCI_MSK, \
97 PWR_BASEADDR_MAC , PWR_CMD_WRITE, BIT(3) | BIT(4), BIT(3) | BIT(4)},\
98 /*Set SDIO suspend local register*/ \
99 {0x0086, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK, \
100 PWR_BASEADDR_SDIO , PWR_CMD_WRITE, BIT(0), BIT(0)}, \
101 /*wait power state to suspend*/ \
102 {0x0086, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK, \
103 PWR_BASEADDR_SDIO , PWR_CMD_POLLING, BIT(1), 0},
104
105 #define RTL8192E_TRANS_SUS_TO_CARDEMU \
106 /* format */ \
107 /* comments here */ \
108 /* { offset, cut_msk, fab_msk|interface_msk, base|cmd, msk, value },*/\
109 /*Set SDIO suspend local register*/ \
110 {0x0086, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK, \
111 PWR_BASEADDR_SDIO , PWR_CMD_WRITE, BIT(0), 0}, \
112 /*wait power state to suspend*/ \
113 {0x0086, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK, \
114 PWR_BASEADDR_SDIO , PWR_CMD_POLLING, BIT(1), BIT(1)}, \
115 /*0x04[12:11] = 2b'00 disable WL suspend*/ \
116 {0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, \
117 PWR_BASEADDR_MAC , PWR_CMD_WRITE, BIT(3) | BIT(4), 0},
118
119 #define RTL8192E_TRANS_CARDEMU_TO_CARDDIS \
120 /* format */ \
121 /* comments here */ \
122 /* { offset, cut_msk, fab_msk|interface_msk, base|cmd, msk, value },*/\
123 /*0x07=0x20 , SOP option to disable BG/MB*/ \
124 {0x0007, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK, \
125 PWR_BASEADDR_MAC , PWR_CMD_WRITE, 0xFF, 0x20}, \
126 /*Unlock small LDO Register*/ \
127 {0x00CC, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK, \
128 PWR_BASEADDR_MAC , PWR_CMD_WRITE, BIT(2), BIT(2)}, \
129 /*Disable small LDO*/ \
130 {0x0011, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK, \
131 PWR_BASEADDR_MAC , PWR_CMD_WRITE, BIT(0), 0}, \
132 /*0x04[12:11] = 2b'01 enable WL suspend*/ \
133 {0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, \
134 PWR_INTF_USB_MSK|PWR_INTF_SDIO_MSK, PWR_BASEADDR_MAC, \
135 PWR_CMD_WRITE, BIT(3)|BIT(4), BIT(3)}, \
136 /*0x04[10] = 1, enable SW LPS*/ \
137 {0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_PCI_MSK, \
138 PWR_BASEADDR_MAC , PWR_CMD_WRITE, BIT(2), BIT(2)}, \
139 /*Set SDIO suspend local register*/ \
140 {0x0086, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK, \
141 PWR_BASEADDR_SDIO , PWR_CMD_WRITE, BIT(0), BIT(0)}, \
142 /*wait power state to suspend*/ \
143 {0x0086, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK, \
144 PWR_BASEADDR_SDIO , PWR_CMD_POLLING, BIT(1), 0},
145
146 #define RTL8192E_TRANS_CARDDIS_TO_CARDEMU \
147 /* format */ \
148 /* comments here */ \
149 /* { offset, cut_msk, fab_msk|interface_msk, base|cmd, msk, value },*/\
150 /*Set SDIO suspend local register*/ \
151 {0x0086, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK, \
152 PWR_BASEADDR_SDIO , PWR_CMD_WRITE, BIT(0), 0}, \
153 /*wait power state to suspend*/ \
154 {0x0086, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK, \
155 PWR_BASEADDR_SDIO , PWR_CMD_POLLING, BIT(1), BIT(1)}, \
156 /*Enable small LDO*/ \
157 {0x0011, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK, \
158 PWR_BASEADDR_MAC , PWR_CMD_WRITE, BIT(0), BIT(0)}, \
159 /*Lock small LDO Register*/ \
160 {0x00CC, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK, \
161 PWR_BASEADDR_MAC , PWR_CMD_WRITE, BIT(2), 0}, \
162 /*0x04[12:11] = 2b'00 disable WL suspend*/ \
163 {0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, \
164 PWR_BASEADDR_MAC , PWR_CMD_WRITE, BIT(3) | BIT(4), 0},
165
166 #define RTL8192E_TRANS_CARDEMU_TO_PDN \
167 /* format */ \
168 /* comments here */ \
169 /* { offset, cut_msk, fab_msk|interface_msk, base|cmd, msk, value },*/\
170 /* 0x04[16] = 0*/ \
171 {0x0006, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, \
172 PWR_BASEADDR_MAC , PWR_CMD_WRITE, BIT(0), 0}, \
173 /* 0x04[15] = 1*/ \
174 {0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, \
175 PWR_BASEADDR_MAC , PWR_CMD_WRITE, BIT(7), BIT(7)},
176
177 #define RTL8192E_TRANS_PDN_TO_CARDEMU \
178 /* format */ \
179 /* comments here */ \
180 /* { offset, cut_msk, fab_msk|interface_msk, base|cmd, msk, value },*/\
181 /* 0x04[15] = 0*/ \
182 {0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, \
183 PWR_BASEADDR_MAC , PWR_CMD_WRITE, BIT(7), 0},
184
185 #define RTL8192E_TRANS_ACT_TO_LPS \
186 /* format */ \
187 /* comments here */ \
188 /* { offset, cut_msk, fab_msk|interface_msk, base|cmd, msk, value },*/\
189 /*PCIe DMA stop*/ \
190 {0x0301, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_PCI_MSK, \
191 PWR_BASEADDR_MAC , PWR_CMD_WRITE, 0xFF, 0xFF}, \
192 /*Tx Pause*/ \
193 {0x0522, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, \
194 PWR_BASEADDR_MAC , PWR_CMD_WRITE, 0xFF, 0xFF}, \
195 /*Should be zero if no packet is transmitting*/ \
196 {0x05F8, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, \
197 PWR_BASEADDR_MAC , PWR_CMD_POLLING, 0xFF, 0}, \
198 /*Should be zero if no packet is transmitting*/ \
199 {0x05F9, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, \
200 PWR_BASEADDR_MAC , PWR_CMD_POLLING, 0xFF, 0}, \
201 /*Should be zero if no packet is transmitting*/ \
202 {0x05FA, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, \
203 PWR_BASEADDR_MAC , PWR_CMD_POLLING, 0xFF, 0}, \
204 /*Should be zero if no packet is transmitting*/ \
205 {0x05FB, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, \
206 PWR_BASEADDR_MAC , PWR_CMD_POLLING, 0xFF, 0}, \
207 /*CCK and OFDM are disabled,and clock are gated*/ \
208 {0x0002, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, \
209 PWR_BASEADDR_MAC , PWR_CMD_WRITE, BIT(0), 0}, \
210 /*Delay 1us*/ \
211 {0x0002, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, \
212 PWR_BASEADDR_MAC , PWR_CMD_DELAY, 0, PWRSEQ_DELAY_US}, \
213 /*Whole BB is reset*/ \
214 {0x0002, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, \
215 PWR_BASEADDR_MAC , PWR_CMD_WRITE, BIT(1), 0}, \
216 /*Reset MAC TRX*/ \
217 {0x0100, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, \
218 PWR_BASEADDR_MAC , PWR_CMD_WRITE, 0xFF, 0x03}, \
219 /*check if removed later*/ \
220 {0x0101, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, \
221 PWR_BASEADDR_MAC , PWR_CMD_WRITE, BIT(1), 0}, \
222 /*When driver enter Sus/ Disable, enable LOP for BT*/ \
223 {0x0093, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK, \
224 PWR_BASEADDR_MAC , PWR_CMD_WRITE, 0xFF, 0x00}, \
225 /*Respond TxOK to scheduler*/ \
226 {0x0553, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, \
227 PWR_BASEADDR_MAC , PWR_CMD_WRITE, BIT(5), BIT(5)},
228
229 #define RTL8192E_TRANS_LPS_TO_ACT \
230 /* format */ \
231 /* comments here */ \
232 /* { offset, cut_msk, fab_msk|interface_msk, base|cmd, msk, value },*/\
233 /*SDIO RPWM, For Repeatly In and out, Taggle bit should be changed*/\
234 {0x0080, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK, \
235 PWR_BASEADDR_SDIO , PWR_CMD_WRITE, 0xFF, 0x84}, \
236 /*USB RPWM*/ \
237 {0xFE58, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_USB_MSK, \
238 PWR_BASEADDR_MAC , PWR_CMD_WRITE, 0xFF, 0x84}, \
239 /*PCIe RPWM*/ \
240 {0x0361, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_PCI_MSK, \
241 PWR_BASEADDR_MAC , PWR_CMD_WRITE, 0xFF, 0x84}, \
242 /*Delay*/ \
243 {0x0002, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, \
244 PWR_BASEADDR_MAC , PWR_CMD_DELAY, 0, PWRSEQ_DELAY_MS}, \
245 /*0x08[4] = 0 switch TSF to 40M*/ \
246 {0x0008, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, \
247 PWR_BASEADDR_MAC , PWR_CMD_WRITE, BIT(4), 0}, \
248 /*Polling 0x109[7]=0 TSF in 40M*/ \
249 {0x0109, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, \
250 PWR_BASEADDR_MAC , PWR_CMD_POLLING, BIT(7), 0}, \
251 /*0x101[1] = 1*/ \
252 {0x0101, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, \
253 PWR_BASEADDR_MAC , PWR_CMD_WRITE, BIT(1), BIT(1)}, \
254 /*0x100[7:0] = 0xFF enable WMAC TRX*/ \
255 {0x0100, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, \
256 PWR_BASEADDR_MAC , PWR_CMD_WRITE, 0xFF, 0xFF}, \
257 /* 0x02[1:0] = 2b'11 enable BB macro*/ \
258 {0x0002, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, \
259 PWR_BASEADDR_MAC , PWR_CMD_WRITE, BIT(1) | BIT(0), BIT(1) | BIT(0)},\
260 /*0x522 = 0*/ \
261 {0x0522, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, \
262 PWR_BASEADDR_MAC , PWR_CMD_WRITE, 0xFF, 0}, \
263 /*Clear ISR*/ \
264 {0x013D, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, \
265 PWR_BASEADDR_MAC , PWR_CMD_WRITE, 0xFF, 0xFF},
266
267 #define RTL8192E_TRANS_END \
268 /* format */ \
269 /* comments here */ \
270 /* { offset, cut_msk, fab_msk|interface_msk, base|cmd, msk, value },*/\
271 {0xFFFF, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, \
272 0, PWR_CMD_END, 0, 0},
273
274 extern struct wlan_pwr_cfg rtl8192E_power_on_flow
275 [RTL8192E_TRANS_CARDEMU_TO_ACT_STEPS +
276 RTL8192E_TRANS_END_STEPS];
277 extern struct wlan_pwr_cfg rtl8192E_radio_off_flow
278 [RTL8192E_TRANS_ACT_TO_CARDEMU_STEPS +
279 RTL8192E_TRANS_END_STEPS];
280 extern struct wlan_pwr_cfg rtl8192E_card_disable_flow
281 [RTL8192E_TRANS_ACT_TO_CARDEMU_STEPS +
282 RTL8192E_TRANS_CARDEMU_TO_PDN_STEPS +
283 RTL8192E_TRANS_END_STEPS];
284 extern struct wlan_pwr_cfg rtl8192E_card_enable_flow
285 [RTL8192E_TRANS_ACT_TO_CARDEMU_STEPS +
286 RTL8192E_TRANS_CARDEMU_TO_PDN_STEPS +
287 RTL8192E_TRANS_END_STEPS];
288 extern struct wlan_pwr_cfg rtl8192E_suspend_flow
289 [RTL8192E_TRANS_ACT_TO_CARDEMU_STEPS +
290 RTL8192E_TRANS_CARDEMU_TO_SUS_STEPS +
291 RTL8192E_TRANS_END_STEPS];
292 extern struct wlan_pwr_cfg rtl8192E_resume_flow
293 [RTL8192E_TRANS_ACT_TO_CARDEMU_STEPS +
294 RTL8192E_TRANS_CARDEMU_TO_SUS_STEPS +
295 RTL8192E_TRANS_END_STEPS];
296 extern struct wlan_pwr_cfg rtl8192E_hwpdn_flow
297 [RTL8192E_TRANS_ACT_TO_CARDEMU_STEPS +
298 RTL8192E_TRANS_CARDEMU_TO_PDN_STEPS +
299 RTL8192E_TRANS_END_STEPS];
300 extern struct wlan_pwr_cfg rtl8192E_enter_lps_flow
301 [RTL8192E_TRANS_ACT_TO_LPS_STEPS +
302 RTL8192E_TRANS_END_STEPS];
303 extern struct wlan_pwr_cfg rtl8192E_leave_lps_flow
304 [RTL8192E_TRANS_LPS_TO_ACT_STEPS +
305 RTL8192E_TRANS_END_STEPS];
306
307 /* RTL8192EE Power Configuration CMDs for PCIe interface */
308 #define RTL8192E_NIC_PWR_ON_FLOW rtl8192E_power_on_flow
309 #define RTL8192E_NIC_RF_OFF_FLOW rtl8192E_radio_off_flow
310 #define RTL8192E_NIC_DISABLE_FLOW rtl8192E_card_disable_flow
311 #define RTL8192E_NIC_ENABLE_FLOW rtl8192E_card_enable_flow
312 #define RTL8192E_NIC_SUSPEND_FLOW rtl8192E_suspend_flow
313 #define RTL8192E_NIC_RESUME_FLOW rtl8192E_resume_flow
314 #define RTL8192E_NIC_PDN_FLOW rtl8192E_hwpdn_flow
315 #define RTL8192E_NIC_LPS_ENTER_FLOW rtl8192E_enter_lps_flow
316 #define RTL8192E_NIC_LPS_LEAVE_FLOW rtl8192E_leave_lps_flow
317
318 #endif
Linux with added FPC-III support