x86/efi: Enforce CONFIG_RELOCATABLE for EFI boot stub

[linux/fpc-iii.git] / Documentation / device-mapper / thin-provisioning.txt

Introduction
============

This document describes a collection of device-mapper targets that
between them implement thin-provisioning and snapshots.

The main highlight of this implementation, compared to the previous
implementation of snapshots, is that it allows many virtual devices to
be stored on the same data volume.  This simplifies administration and
allows the sharing of data between volumes, thus reducing disk usage.

Another significant feature is support for an arbitrary depth of
recursive snapshots (snapshots of snapshots of snapshots ...).  The
previous implementation of snapshots did this by chaining together
lookup tables, and so performance was O(depth).  This new
implementation uses a single data structure to avoid this degradation
with depth.  Fragmentation may still be an issue, however, in some
scenarios.

Metadata is stored on a separate device from data, giving the
administrator some freedom, for example to:

- Improve metadata resilience by storing metadata on a mirrored volume
  but data on a non-mirrored one.

- Improve performance by storing the metadata on SSD.

Status
======

These targets are very much still in the EXPERIMENTAL state.  Please
do not yet rely on them in production.  But do experiment and offer us
feedback.  Different use cases will have different performance
characteristics, for example due to fragmentation of the data volume.

If you find this software is not performing as expected please mail
dm-devel@redhat.com with details and we'll try our best to improve
things for you.

Userspace tools for checking and repairing the metadata are under
development.

Cookbook
========

This section describes some quick recipes for using thin provisioning.
They use the dmsetup program to control the device-mapper driver
directly.  End users will be advised to use a higher-level volume
manager such as LVM2 once support has been added.

Pool device
-----------

The pool device ties together the metadata volume and the data volume.
It maps I/O linearly to the data volume and updates the metadata via
two mechanisms:

- Function calls from the thin targets

- Device-mapper 'messages' from userspace which control the creation of new
  virtual devices amongst other things.

Setting up a fresh pool device
------------------------------

Setting up a pool device requires a valid metadata device, and a
data device.  If you do not have an existing metadata device you can
make one by zeroing the first 4k to indicate empty metadata.

    dd if=/dev/zero of=$metadata_dev bs=4096 count=1

The amount of metadata you need will vary according to how many blocks
are shared between thin devices (i.e. through snapshots).  If you have
less sharing than average you'll need a larger-than-average metadata device.

As a guide, we suggest you calculate the number of bytes to use in the
metadata device as 48 * $data_dev_size / $data_block_size but round it up
to 2MB if the answer is smaller.  If you're creating large numbers of
snapshots which are recording large amounts of change, you may find you
need to increase this.

The largest size supported is 16GB: If the device is larger,
a warning will be issued and the excess space will not be used.

Reloading a pool table
----------------------

You may reload a pool's table, indeed this is how the pool is resized
if it runs out of space.  (N.B. While specifying a different metadata
device when reloading is not forbidden at the moment, things will go
wrong if it does not route I/O to exactly the same on-disk location as
previously.)

Using an existing pool device
-----------------------------

    dmsetup create pool \
        --table "0 20971520 thin-pool $metadata_dev $data_dev \
                 $data_block_size $low_water_mark"

$data_block_size gives the smallest unit of disk space that can be
allocated at a time expressed in units of 512-byte sectors.
$data_block_size must be between 128 (64KB) and 2097152 (1GB) and a
multiple of 128 (64KB).  $data_block_size cannot be changed after the
thin-pool is created.  People primarily interested in thin provisioning
may want to use a value such as 1024 (512KB).  People doing lots of
snapshotting may want a smaller value such as 128 (64KB).  If you are
not zeroing newly-allocated data, a larger $data_block_size in the
region of 256000 (128MB) is suggested.

$low_water_mark is expressed in blocks of size $data_block_size.  If
free space on the data device drops below this level then a dm event
will be triggered which a userspace daemon should catch allowing it to
extend the pool device.  Only one such event will be sent.
Resuming a device with a new table itself triggers an event so the
userspace daemon can use this to detect a situation where a new table
already exceeds the threshold.

Thin provisioning
-----------------

i) Creating a new thinly-provisioned volume.

  To create a new thinly- provisioned volume you must send a message to an
  active pool device, /dev/mapper/pool in this example.

    dmsetup message /dev/mapper/pool 0 "create_thin 0"

  Here '0' is an identifier for the volume, a 24-bit number.  It's up
  to the caller to allocate and manage these identifiers.  If the
  identifier is already in use, the message will fail with -EEXIST.

ii) Using a thinly-provisioned volume.

  Thinly-provisioned volumes are activated using the 'thin' target:

    dmsetup create thin --table "0 2097152 thin /dev/mapper/pool 0"

  The last parameter is the identifier for the thinp device.

Internal snapshots
------------------

i) Creating an internal snapshot.

  Snapshots are created with another message to the pool.

  N.B.  If the origin device that you wish to snapshot is active, you
  must suspend it before creating the snapshot to avoid corruption.
  This is NOT enforced at the moment, so please be careful!

    dmsetup suspend /dev/mapper/thin
    dmsetup message /dev/mapper/pool 0 "create_snap 1 0"
    dmsetup resume /dev/mapper/thin

  Here '1' is the identifier for the volume, a 24-bit number.  '0' is the
  identifier for the origin device.

ii) Using an internal snapshot.

  Once created, the user doesn't have to worry about any connection
  between the origin and the snapshot.  Indeed the snapshot is no
  different from any other thinly-provisioned device and can be
  snapshotted itself via the same method.  It's perfectly legal to
  have only one of them active, and there's no ordering requirement on
  activating or removing them both.  (This differs from conventional
  device-mapper snapshots.)

  Activate it exactly the same way as any other thinly-provisioned volume:

    dmsetup create snap --table "0 2097152 thin /dev/mapper/pool 1"

External snapshots
------------------

You can use an external _read only_ device as an origin for a
thinly-provisioned volume.  Any read to an unprovisioned area of the
thin device will be passed through to the origin.  Writes trigger
the allocation of new blocks as usual.

One use case for this is VM hosts that want to run guests on
thinly-provisioned volumes but have the base image on another device
(possibly shared between many VMs).

You must not write to the origin device if you use this technique!
Of course, you may write to the thin device and take internal snapshots
of the thin volume.

i) Creating a snapshot of an external device

  This is the same as creating a thin device.
  You don't mention the origin at this stage.

    dmsetup message /dev/mapper/pool 0 "create_thin 0"

ii) Using a snapshot of an external device.

  Append an extra parameter to the thin target specifying the origin:

    dmsetup create snap --table "0 2097152 thin /dev/mapper/pool 0 /dev/image"

  N.B. All descendants (internal snapshots) of this snapshot require the
  same extra origin parameter.

Deactivation
------------

All devices using a pool must be deactivated before the pool itself
can be.

    dmsetup remove thin
    dmsetup remove snap
    dmsetup remove pool

Reference
=========

'thin-pool' target
------------------

i) Constructor

    thin-pool <metadata dev> <data dev> <data block size (sectors)> \
              <low water mark (blocks)> [<number of feature args> [<arg>]*]

    Optional feature arguments:

      skip_block_zeroing: Skip the zeroing of newly-provisioned blocks.

      ignore_discard: Disable discard support.

      no_discard_passdown: Don't pass discards down to the underlying
                           data device, but just remove the mapping.

      read_only: Don't allow any changes to be made to the pool
                 metadata.

    Data block size must be between 64KB (128 sectors) and 1GB
    (2097152 sectors) inclusive.


ii) Status

    <transaction id> <used metadata blocks>/<total metadata blocks>
    <used data blocks>/<total data blocks> <held metadata root>
    [no_]discard_passdown ro|rw

    transaction id:
        A 64-bit number used by userspace to help synchronise with metadata
        from volume managers.

    used data blocks / total data blocks
        If the number of free blocks drops below the pool's low water mark a
        dm event will be sent to userspace.  This event is edge-triggered and
        it will occur only once after each resume so volume manager writers
        should register for the event and then check the target's status.

    held metadata root:
        The location, in sectors, of the metadata root that has been
        'held' for userspace read access.  '-' indicates there is no
        held root.  This feature is not yet implemented so '-' is
        always returned.

    discard_passdown|no_discard_passdown
        Whether or not discards are actually being passed down to the
        underlying device.  When this is enabled when loading the table,
        it can get disabled if the underlying device doesn't support it.

    ro|rw
        If the pool encounters certain types of device failures it will
        drop into a read-only metadata mode in which no changes to
        the pool metadata (like allocating new blocks) are permitted.

        In serious cases where even a read-only mode is deemed unsafe
        no further I/O will be permitted and the status will just
        contain the string 'Fail'.  The userspace recovery tools
        should then be used.

iii) Messages

    create_thin <dev id>

        Create a new thinly-provisioned device.
        <dev id> is an arbitrary unique 24-bit identifier chosen by
        the caller.

    create_snap <dev id> <origin id>

        Create a new snapshot of another thinly-provisioned device.
        <dev id> is an arbitrary unique 24-bit identifier chosen by
        the caller.
        <origin id> is the identifier of the thinly-provisioned device
        of which the new device will be a snapshot.

    delete <dev id>

        Deletes a thin device.  Irreversible.

    set_transaction_id <current id> <new id>

        Userland volume managers, such as LVM, need a way to
        synchronise their external metadata with the internal metadata of the
        pool target.  The thin-pool target offers to store an
        arbitrary 64-bit transaction id and return it on the target's
        status line.  To avoid races you must provide what you think
        the current transaction id is when you change it with this
        compare-and-swap message.

    reserve_metadata_snap

        Reserve a copy of the data mapping btree for use by userland.
        This allows userland to inspect the mappings as they were when
        this message was executed.  Use the pool's status command to
        get the root block associated with the metadata snapshot.

    release_metadata_snap

        Release a previously reserved copy of the data mapping btree.

'thin' target
-------------

i) Constructor

    thin <pool dev> <dev id> [<external origin dev>]

    pool dev:
        the thin-pool device, e.g. /dev/mapper/my_pool or 253:0

    dev id:
        the internal device identifier of the device to be
        activated.

    external origin dev:
        an optional block device outside the pool to be treated as a
        read-only snapshot origin: reads to unprovisioned areas of the
        thin target will be mapped to this device.

The pool doesn't store any size against the thin devices.  If you
load a thin target that is smaller than you've been using previously,
then you'll have no access to blocks mapped beyond the end.  If you
load a target that is bigger than before, then extra blocks will be
provisioned as and when needed.

If you wish to reduce the size of your thin device and potentially
regain some space then send the 'trim' message to the pool.

ii) Status

     <nr mapped sectors> <highest mapped sector>

        If the pool has encountered device errors and failed, the status
        will just contain the string 'Fail'.  The userspace recovery
        tools should then be used.