arch/mips/alchemy/devboards/db1550.c

   1 /*
   2  * Alchemy Db1550/Pb1550 board support
   3  *
   4  * (c) 2011 Manuel Lauss <manuel.lauss@googlemail.com>
   5  */
   6
   7 #include <linux/dma-mapping.h>
   8 #include <linux/gpio.h>
   9 #include <linux/i2c.h>
  10 #include <linux/init.h>
  11 #include <linux/io.h>
  12 #include <linux/interrupt.h>
  13 #include <linux/mtd/mtd.h>
  14 #include <linux/mtd/nand.h>
  15 #include <linux/mtd/partitions.h>
  16 #include <linux/platform_device.h>
  17 #include <linux/pm.h>
  18 #include <linux/spi/spi.h>
  19 #include <linux/spi/flash.h>
  20 #include <asm/bootinfo.h>
  21 #include <asm/mach-au1x00/au1000.h>
  22 #include <asm/mach-au1x00/au1xxx_eth.h>
  23 #include <asm/mach-au1x00/au1xxx_dbdma.h>
  24 #include <asm/mach-au1x00/au1xxx_psc.h>
  25 #include <asm/mach-au1x00/au1550_spi.h>
  26 #include <asm/mach-au1x00/au1550nd.h>
  27 #include <asm/mach-db1x00/bcsr.h>
  28 #include <prom.h>
  29 #include "platform.h"
  30
  31 static void __init db1550_hw_setup(void)
  32 {
  33         void __iomem *base;
  34
  35         /* complete SPI setup: link psc0_intclk to a 48MHz source,
  36          * and assign GPIO16 to PSC0_SYNC1 (SPI cs# line) as well as PSC1_SYNC
  37          * for AC97 on PB1550.
  38          */
  39         base = (void __iomem *)SYS_CLKSRC;
  40         __raw_writel(__raw_readl(base) | 0x000001e0, base);
  41         base = (void __iomem *)SYS_PINFUNC;
  42         __raw_writel(__raw_readl(base) | 1 | SYS_PF_PSC1_S1, base);
  43         wmb();
  44
  45         /* reset the AC97 codec now, the reset time in the psc-ac97 driver
  46          * is apparently too short although it's ridiculous as it is.
  47          */
  48         base = (void __iomem *)KSEG1ADDR(AU1550_PSC1_PHYS_ADDR);
  49         __raw_writel(PSC_SEL_CLK_SERCLK | PSC_SEL_PS_AC97MODE,
  50                      base + PSC_SEL_OFFSET);
  51         __raw_writel(PSC_CTRL_DISABLE, base + PSC_CTRL_OFFSET);
  52         wmb();
  53         __raw_writel(PSC_AC97RST_RST, base + PSC_AC97RST_OFFSET);
  54         wmb();
  55 }
  56
  57 int __init db1550_board_setup(void)
  58 {
  59         unsigned short whoami;
  60
  61         bcsr_init(DB1550_BCSR_PHYS_ADDR,
  62                   DB1550_BCSR_PHYS_ADDR + DB1550_BCSR_HEXLED_OFS);
  63
  64         whoami = bcsr_read(BCSR_WHOAMI); /* PB1550 hexled offset differs */
  65         if ((BCSR_WHOAMI_BOARD(whoami) == BCSR_WHOAMI_PB1550_SDR) ||
  66             (BCSR_WHOAMI_BOARD(whoami) == BCSR_WHOAMI_PB1550_DDR))
  67                 bcsr_init(PB1550_BCSR_PHYS_ADDR,
  68                           PB1550_BCSR_PHYS_ADDR + PB1550_BCSR_HEXLED_OFS);
  69
  70         pr_info("Alchemy/AMD %s Board, CPLD Rev %d Board-ID %d  "       \
  71                 "Daughtercard ID %d\n", get_system_type(),
  72                 (whoami >> 4) & 0xf, (whoami >> 8) & 0xf, whoami & 0xf);
  73
  74         db1550_hw_setup();
  75         return 0;
  76 }
  77
  78 /*****************************************************************************/
  79
  80 static struct mtd_partition db1550_spiflash_parts[] = {
  81         {
  82                 .name   = "spi_flash",
  83                 .offset = 0,
  84                 .size   = MTDPART_SIZ_FULL,
  85         },
  86 };
  87
  88 static struct flash_platform_data db1550_spiflash_data = {
  89         .name           = "s25fl010",
  90         .parts          = db1550_spiflash_parts,
  91         .nr_parts       = ARRAY_SIZE(db1550_spiflash_parts),
  92         .type           = "m25p10",
  93 };
  94
  95 static struct spi_board_info db1550_spi_devs[] __initdata = {
  96         {
  97                 /* TI TMP121AIDBVR temp sensor */
  98                 .modalias       = "tmp121",
  99                 .max_speed_hz   = 2400000,
 100                 .bus_num        = 0,
 101                 .chip_select    = 0,
 102                 .mode           = SPI_MODE_0,
 103         },
 104         {
 105                 /* Spansion S25FL001D0FMA SPI flash */
 106                 .modalias       = "m25p80",
 107                 .max_speed_hz   = 2400000,
 108                 .bus_num        = 0,
 109                 .chip_select    = 1,
 110                 .mode           = SPI_MODE_0,
 111                 .platform_data  = &db1550_spiflash_data,
 112         },
 113 };
 114
 115 static struct i2c_board_info db1550_i2c_devs[] __initdata = {
 116         { I2C_BOARD_INFO("24c04",  0x52),}, /* AT24C04-10 I2C eeprom */
 117         { I2C_BOARD_INFO("ne1619", 0x2d),}, /* adm1025-compat hwmon */
 118         { I2C_BOARD_INFO("wm8731", 0x1b),}, /* I2S audio codec WM8731 */
 119 };
 120
 121 /**********************************************************************/
 122
 123 static void au1550_nand_cmd_ctrl(struct mtd_info *mtd, int cmd,
 124                                  unsigned int ctrl)
 125 {
 126         struct nand_chip *this = mtd->priv;
 127         unsigned long ioaddr = (unsigned long)this->IO_ADDR_W;
 128
 129         ioaddr &= 0xffffff00;
 130
 131         if (ctrl & NAND_CLE) {
 132                 ioaddr += MEM_STNAND_CMD;
 133         } else if (ctrl & NAND_ALE) {
 134                 ioaddr += MEM_STNAND_ADDR;
 135         } else {
 136                 /* assume we want to r/w real data  by default */
 137                 ioaddr += MEM_STNAND_DATA;
 138         }
 139         this->IO_ADDR_R = this->IO_ADDR_W = (void __iomem *)ioaddr;
 140         if (cmd != NAND_CMD_NONE) {
 141                 __raw_writeb(cmd, this->IO_ADDR_W);
 142                 wmb();
 143         }
 144 }
 145
 146 static int au1550_nand_device_ready(struct mtd_info *mtd)
 147 {
 148         return __raw_readl((void __iomem *)MEM_STSTAT) & 1;
 149 }
 150
 151 static struct mtd_partition db1550_nand_parts[] = {
 152         {
 153                 .name   = "NAND FS 0",
 154                 .offset = 0,
 155                 .size   = 8 * 1024 * 1024,
 156         },
 157         {
 158                 .name   = "NAND FS 1",
 159                 .offset = MTDPART_OFS_APPEND,
 160                 .size   = MTDPART_SIZ_FULL
 161         },
 162 };
 163
 164 struct platform_nand_data db1550_nand_platdata = {
 165         .chip = {
 166                 .nr_chips       = 1,
 167                 .chip_offset    = 0,
 168                 .nr_partitions  = ARRAY_SIZE(db1550_nand_parts),
 169                 .partitions     = db1550_nand_parts,
 170                 .chip_delay     = 20,
 171         },
 172         .ctrl = {
 173                 .dev_ready      = au1550_nand_device_ready,
 174                 .cmd_ctrl       = au1550_nand_cmd_ctrl,
 175         },
 176 };
 177
 178 static struct resource db1550_nand_res[] = {
 179         [0] = {
 180                 .start  = 0x20000000,
 181                 .end    = 0x200000ff,
 182                 .flags  = IORESOURCE_MEM,
 183         },
 184 };
 185
 186 static struct platform_device db1550_nand_dev = {
 187         .name           = "gen_nand",
 188         .num_resources  = ARRAY_SIZE(db1550_nand_res),
 189         .resource       = db1550_nand_res,
 190         .id             = -1,
 191         .dev            = {
 192                 .platform_data = &db1550_nand_platdata,
 193         }
 194 };
 195
 196 static struct au1550nd_platdata pb1550_nand_pd = {
 197         .parts          = db1550_nand_parts,
 198         .num_parts      = ARRAY_SIZE(db1550_nand_parts),
 199         .devwidth       = 0,    /* x8 NAND default, needs fixing up */
 200 };
 201
 202 static struct platform_device pb1550_nand_dev = {
 203         .name           = "au1550-nand",
 204         .id             = -1,
 205         .resource       = db1550_nand_res,
 206         .num_resources  = ARRAY_SIZE(db1550_nand_res),
 207         .dev            = {
 208                 .platform_data  = &pb1550_nand_pd,
 209         },
 210 };
 211
 212 static void __init pb1550_nand_setup(void)
 213 {
 214         int boot_swapboot = (au_readl(MEM_STSTAT) & (0x7 << 1)) |
 215                             ((bcsr_read(BCSR_STATUS) >> 6) & 0x1);
 216
 217         gpio_direction_input(206);      /* de-assert NAND CS# */
 218         switch (boot_swapboot) {
 219         case 0: case 2: case 8: case 0xC: case 0xD:
 220                 /* x16 NAND Flash */
 221                 pb1550_nand_pd.devwidth = 1;
 222                 /* fallthrough */
 223         case 1: case 3: case 9: case 0xE: case 0xF:
 224                 /* x8 NAND, already set up */
 225                 platform_device_register(&pb1550_nand_dev);
 226         }
 227 }
 228
 229 /**********************************************************************/
 230
 231 static struct resource au1550_psc0_res[] = {
 232         [0] = {
 233                 .start  = AU1550_PSC0_PHYS_ADDR,
 234                 .end    = AU1550_PSC0_PHYS_ADDR + 0xfff,
 235                 .flags  = IORESOURCE_MEM,
 236         },
 237         [1] = {
 238                 .start  = AU1550_PSC0_INT,
 239                 .end    = AU1550_PSC0_INT,
 240                 .flags  = IORESOURCE_IRQ,
 241         },
 242         [2] = {
 243                 .start  = AU1550_DSCR_CMD0_PSC0_TX,
 244                 .end    = AU1550_DSCR_CMD0_PSC0_TX,
 245                 .flags  = IORESOURCE_DMA,
 246         },
 247         [3] = {
 248                 .start  = AU1550_DSCR_CMD0_PSC0_RX,
 249                 .end    = AU1550_DSCR_CMD0_PSC0_RX,
 250                 .flags  = IORESOURCE_DMA,
 251         },
 252 };
 253
 254 static void db1550_spi_cs_en(struct au1550_spi_info *spi, int cs, int pol)
 255 {
 256         if (cs)
 257                 bcsr_mod(BCSR_BOARD, 0, BCSR_BOARD_SPISEL);
 258         else
 259                 bcsr_mod(BCSR_BOARD, BCSR_BOARD_SPISEL, 0);
 260 }
 261
 262 static struct au1550_spi_info db1550_spi_platdata = {
 263         .mainclk_hz     = 48000000,     /* PSC0 clock: max. 2.4MHz SPI clk */
 264         .num_chipselect = 2,
 265         .activate_cs    = db1550_spi_cs_en,
 266 };
 267
 268 static u64 spi_dmamask = DMA_BIT_MASK(32);
 269
 270 static struct platform_device db1550_spi_dev = {
 271         .dev    = {
 272                 .dma_mask               = &spi_dmamask,
 273                 .coherent_dma_mask      = DMA_BIT_MASK(32),
 274                 .platform_data          = &db1550_spi_platdata,
 275         },
 276         .name           = "au1550-spi",
 277         .id             = 0,    /* bus number */
 278         .num_resources  = ARRAY_SIZE(au1550_psc0_res),
 279         .resource       = au1550_psc0_res,
 280 };
 281
 282 /**********************************************************************/
 283
 284 static struct resource au1550_psc1_res[] = {
 285         [0] = {
 286                 .start  = AU1550_PSC1_PHYS_ADDR,
 287                 .end    = AU1550_PSC1_PHYS_ADDR + 0xfff,
 288                 .flags  = IORESOURCE_MEM,
 289         },
 290         [1] = {
 291                 .start  = AU1550_PSC1_INT,
 292                 .end    = AU1550_PSC1_INT,
 293                 .flags  = IORESOURCE_IRQ,
 294         },
 295         [2] = {
 296                 .start  = AU1550_DSCR_CMD0_PSC1_TX,
 297                 .end    = AU1550_DSCR_CMD0_PSC1_TX,
 298                 .flags  = IORESOURCE_DMA,
 299         },
 300         [3] = {
 301                 .start  = AU1550_DSCR_CMD0_PSC1_RX,
 302                 .end    = AU1550_DSCR_CMD0_PSC1_RX,
 303                 .flags  = IORESOURCE_DMA,
 304         },
 305 };
 306
 307 static struct platform_device db1550_ac97_dev = {
 308         .name           = "au1xpsc_ac97",
 309         .id             = 1,    /* PSC ID */
 310         .num_resources  = ARRAY_SIZE(au1550_psc1_res),
 311         .resource       = au1550_psc1_res,
 312 };
 313
 314
 315 static struct resource au1550_psc2_res[] = {
 316         [0] = {
 317                 .start  = AU1550_PSC2_PHYS_ADDR,
 318                 .end    = AU1550_PSC2_PHYS_ADDR + 0xfff,
 319                 .flags  = IORESOURCE_MEM,
 320         },
 321         [1] = {
 322                 .start  = AU1550_PSC2_INT,
 323                 .end    = AU1550_PSC2_INT,
 324                 .flags  = IORESOURCE_IRQ,
 325         },
 326         [2] = {
 327                 .start  = AU1550_DSCR_CMD0_PSC2_TX,
 328                 .end    = AU1550_DSCR_CMD0_PSC2_TX,
 329                 .flags  = IORESOURCE_DMA,
 330         },
 331         [3] = {
 332                 .start  = AU1550_DSCR_CMD0_PSC2_RX,
 333                 .end    = AU1550_DSCR_CMD0_PSC2_RX,
 334                 .flags  = IORESOURCE_DMA,
 335         },
 336 };
 337
 338 static struct platform_device db1550_i2c_dev = {
 339         .name           = "au1xpsc_smbus",
 340         .id             = 0,    /* bus number */
 341         .num_resources  = ARRAY_SIZE(au1550_psc2_res),
 342         .resource       = au1550_psc2_res,
 343 };
 344
 345 /**********************************************************************/
 346
 347 static struct resource au1550_psc3_res[] = {
 348         [0] = {
 349                 .start  = AU1550_PSC3_PHYS_ADDR,
 350                 .end    = AU1550_PSC3_PHYS_ADDR + 0xfff,
 351                 .flags  = IORESOURCE_MEM,
 352         },
 353         [1] = {
 354                 .start  = AU1550_PSC3_INT,
 355                 .end    = AU1550_PSC3_INT,
 356                 .flags  = IORESOURCE_IRQ,
 357         },
 358         [2] = {
 359                 .start  = AU1550_DSCR_CMD0_PSC3_TX,
 360                 .end    = AU1550_DSCR_CMD0_PSC3_TX,
 361                 .flags  = IORESOURCE_DMA,
 362         },
 363         [3] = {
 364                 .start  = AU1550_DSCR_CMD0_PSC3_RX,
 365                 .end    = AU1550_DSCR_CMD0_PSC3_RX,
 366                 .flags  = IORESOURCE_DMA,
 367         },
 368 };
 369
 370 static struct platform_device db1550_i2s_dev = {
 371         .name           = "au1xpsc_i2s",
 372         .id             = 3,    /* PSC ID */
 373         .num_resources  = ARRAY_SIZE(au1550_psc3_res),
 374         .resource       = au1550_psc3_res,
 375 };
 376
 377 /**********************************************************************/
 378
 379 static struct platform_device db1550_stac_dev = {
 380         .name           = "ac97-codec",
 381         .id             = 1,    /* on PSC1 */
 382 };
 383
 384 static struct platform_device db1550_ac97dma_dev = {
 385         .name           = "au1xpsc-pcm",
 386         .id             = 1,    /* on PSC3 */
 387 };
 388
 389 static struct platform_device db1550_i2sdma_dev = {
 390         .name           = "au1xpsc-pcm",
 391         .id             = 3,    /* on PSC3 */
 392 };
 393
 394 static struct platform_device db1550_sndac97_dev = {
 395         .name           = "db1550-ac97",
 396 };
 397
 398 static struct platform_device db1550_sndi2s_dev = {
 399         .name           = "db1550-i2s",
 400 };
 401
 402 /**********************************************************************/
 403
 404 static int db1550_map_pci_irq(const struct pci_dev *d, u8 slot, u8 pin)
 405 {
 406         if ((slot < 11) || (slot > 13) || pin == 0)
 407                 return -1;
 408         if (slot == 11)
 409                 return (pin == 1) ? AU1550_PCI_INTC : 0xff;
 410         if (slot == 12) {
 411                 switch (pin) {
 412                 case 1: return AU1550_PCI_INTB;
 413                 case 2: return AU1550_PCI_INTC;
 414                 case 3: return AU1550_PCI_INTD;
 415                 case 4: return AU1550_PCI_INTA;
 416                 }
 417         }
 418         if (slot == 13) {
 419                 switch (pin) {
 420                 case 1: return AU1550_PCI_INTA;
 421                 case 2: return AU1550_PCI_INTB;
 422                 case 3: return AU1550_PCI_INTC;
 423                 case 4: return AU1550_PCI_INTD;
 424                 }
 425         }
 426         return -1;
 427 }
 428
 429 static int pb1550_map_pci_irq(const struct pci_dev *d, u8 slot, u8 pin)
 430 {
 431         if ((slot < 12) || (slot > 13) || pin == 0)
 432                 return -1;
 433         if (slot == 12) {
 434                 switch (pin) {
 435                 case 1: return AU1500_PCI_INTB;
 436                 case 2: return AU1500_PCI_INTC;
 437                 case 3: return AU1500_PCI_INTD;
 438                 case 4: return AU1500_PCI_INTA;
 439                 }
 440         }
 441         if (slot == 13) {
 442                 switch (pin) {
 443                 case 1: return AU1500_PCI_INTA;
 444                 case 2: return AU1500_PCI_INTB;
 445                 case 3: return AU1500_PCI_INTC;
 446                 case 4: return AU1500_PCI_INTD;
 447                 }
 448         }
 449         return -1;
 450 }
 451
 452 static struct resource alchemy_pci_host_res[] = {
 453         [0] = {
 454                 .start  = AU1500_PCI_PHYS_ADDR,
 455                 .end    = AU1500_PCI_PHYS_ADDR + 0xfff,
 456                 .flags  = IORESOURCE_MEM,
 457         },
 458 };
 459
 460 static struct alchemy_pci_platdata db1550_pci_pd = {
 461         .board_map_irq  = db1550_map_pci_irq,
 462 };
 463
 464 static struct platform_device db1550_pci_host_dev = {
 465         .dev.platform_data = &db1550_pci_pd,
 466         .name           = "alchemy-pci",
 467         .id             = 0,
 468         .num_resources  = ARRAY_SIZE(alchemy_pci_host_res),
 469         .resource       = alchemy_pci_host_res,
 470 };
 471
 472 /**********************************************************************/
 473
 474 static struct platform_device *db1550_devs[] __initdata = {
 475         &db1550_i2c_dev,
 476         &db1550_ac97_dev,
 477         &db1550_spi_dev,
 478         &db1550_i2s_dev,
 479         &db1550_stac_dev,
 480         &db1550_ac97dma_dev,
 481         &db1550_i2sdma_dev,
 482         &db1550_sndac97_dev,
 483         &db1550_sndi2s_dev,
 484 };
 485
 486 /* must be arch_initcall; MIPS PCI scans busses in a subsys_initcall */
 487 int __init db1550_pci_setup(int id)
 488 {
 489         if (id)
 490                 db1550_pci_pd.board_map_irq = pb1550_map_pci_irq;
 491         return platform_device_register(&db1550_pci_host_dev);
 492 }
 493
 494 static void __init db1550_devices(void)
 495 {
 496         alchemy_gpio_direction_output(203, 0);  /* red led on */
 497
 498         irq_set_irq_type(AU1550_GPIO0_INT, IRQ_TYPE_EDGE_BOTH);  /* CD0# */
 499         irq_set_irq_type(AU1550_GPIO1_INT, IRQ_TYPE_EDGE_BOTH);  /* CD1# */
 500         irq_set_irq_type(AU1550_GPIO3_INT, IRQ_TYPE_LEVEL_LOW);  /* CARD0# */
 501         irq_set_irq_type(AU1550_GPIO5_INT, IRQ_TYPE_LEVEL_LOW);  /* CARD1# */
 502         irq_set_irq_type(AU1550_GPIO21_INT, IRQ_TYPE_LEVEL_LOW); /* STSCHG0# */
 503         irq_set_irq_type(AU1550_GPIO22_INT, IRQ_TYPE_LEVEL_LOW); /* STSCHG1# */
 504
 505         db1x_register_pcmcia_socket(
 506                 AU1000_PCMCIA_ATTR_PHYS_ADDR,
 507                 AU1000_PCMCIA_ATTR_PHYS_ADDR + 0x000400000 - 1,
 508                 AU1000_PCMCIA_MEM_PHYS_ADDR,
 509                 AU1000_PCMCIA_MEM_PHYS_ADDR  + 0x000400000 - 1,
 510                 AU1000_PCMCIA_IO_PHYS_ADDR,
 511                 AU1000_PCMCIA_IO_PHYS_ADDR   + 0x000010000 - 1,
 512                 AU1550_GPIO3_INT, AU1550_GPIO0_INT,
 513                 /*AU1550_GPIO21_INT*/0, 0, 0);
 514
 515         db1x_register_pcmcia_socket(
 516                 AU1000_PCMCIA_ATTR_PHYS_ADDR + 0x004000000,
 517                 AU1000_PCMCIA_ATTR_PHYS_ADDR + 0x004400000 - 1,
 518                 AU1000_PCMCIA_MEM_PHYS_ADDR  + 0x004000000,
 519                 AU1000_PCMCIA_MEM_PHYS_ADDR  + 0x004400000 - 1,
 520                 AU1000_PCMCIA_IO_PHYS_ADDR   + 0x004000000,
 521                 AU1000_PCMCIA_IO_PHYS_ADDR   + 0x004010000 - 1,
 522                 AU1550_GPIO5_INT, AU1550_GPIO1_INT,
 523                 /*AU1550_GPIO22_INT*/0, 0, 1);
 524
 525         platform_device_register(&db1550_nand_dev);
 526
 527         alchemy_gpio_direction_output(202, 0);  /* green led on */
 528 }
 529
 530 static void __init pb1550_devices(void)
 531 {
 532         irq_set_irq_type(AU1550_GPIO0_INT, IRQ_TYPE_LEVEL_LOW);
 533         irq_set_irq_type(AU1550_GPIO1_INT, IRQ_TYPE_LEVEL_LOW);
 534         irq_set_irq_type(AU1550_GPIO201_205_INT, IRQ_TYPE_LEVEL_HIGH);
 535
 536         /* enable both PCMCIA card irqs in the shared line */
 537         alchemy_gpio2_enable_int(201);  /* socket 0 card irq */
 538         alchemy_gpio2_enable_int(202);  /* socket 1 card irq */
 539
 540         /* Pb1550, like all others, also has statuschange irqs; however they're
 541         * wired up on one of the Au1550's shared GPIO201_205 line, which also
 542         * services the PCMCIA card interrupts.  So we ignore statuschange and
 543         * use the GPIO201_205 exclusively for card interrupts, since a) pcmcia
 544         * drivers are used to shared irqs and b) statuschange isn't really use-
 545         * ful anyway.
 546         */
 547         db1x_register_pcmcia_socket(
 548                 AU1000_PCMCIA_ATTR_PHYS_ADDR,
 549                 AU1000_PCMCIA_ATTR_PHYS_ADDR + 0x000400000 - 1,
 550                 AU1000_PCMCIA_MEM_PHYS_ADDR,
 551                 AU1000_PCMCIA_MEM_PHYS_ADDR  + 0x000400000 - 1,
 552                 AU1000_PCMCIA_IO_PHYS_ADDR,
 553                 AU1000_PCMCIA_IO_PHYS_ADDR   + 0x000010000 - 1,
 554                 AU1550_GPIO201_205_INT, AU1550_GPIO0_INT, 0, 0, 0);
 555
 556         db1x_register_pcmcia_socket(
 557                 AU1000_PCMCIA_ATTR_PHYS_ADDR + 0x008000000,
 558                 AU1000_PCMCIA_ATTR_PHYS_ADDR + 0x008400000 - 1,
 559                 AU1000_PCMCIA_MEM_PHYS_ADDR  + 0x008000000,
 560                 AU1000_PCMCIA_MEM_PHYS_ADDR  + 0x008400000 - 1,
 561                 AU1000_PCMCIA_IO_PHYS_ADDR   + 0x008000000,
 562                 AU1000_PCMCIA_IO_PHYS_ADDR   + 0x008010000 - 1,
 563                 AU1550_GPIO201_205_INT, AU1550_GPIO1_INT, 0, 0, 1);
 564
 565         pb1550_nand_setup();
 566 }
 567
 568 int __init db1550_dev_setup(void)
 569 {
 570         int swapped, id;
 571
 572         id = (BCSR_WHOAMI_BOARD(bcsr_read(BCSR_WHOAMI)) != BCSR_WHOAMI_DB1550);
 573
 574         i2c_register_board_info(0, db1550_i2c_devs,
 575                                 ARRAY_SIZE(db1550_i2c_devs));
 576         spi_register_board_info(db1550_spi_devs,
 577                                 ARRAY_SIZE(db1550_i2c_devs));
 578
 579         /* Audio PSC clock is supplied by codecs (PSC1, 3) FIXME: platdata!! */
 580         __raw_writel(PSC_SEL_CLK_SERCLK,
 581             (void __iomem *)KSEG1ADDR(AU1550_PSC1_PHYS_ADDR) + PSC_SEL_OFFSET);
 582         wmb();
 583         __raw_writel(PSC_SEL_CLK_SERCLK,
 584             (void __iomem *)KSEG1ADDR(AU1550_PSC3_PHYS_ADDR) + PSC_SEL_OFFSET);
 585         wmb();
 586         /* SPI/I2C use internally supplied 50MHz source */
 587         __raw_writel(PSC_SEL_CLK_INTCLK,
 588             (void __iomem *)KSEG1ADDR(AU1550_PSC0_PHYS_ADDR) + PSC_SEL_OFFSET);
 589         wmb();
 590         __raw_writel(PSC_SEL_CLK_INTCLK,
 591             (void __iomem *)KSEG1ADDR(AU1550_PSC2_PHYS_ADDR) + PSC_SEL_OFFSET);
 592         wmb();
 593
 594         id ? pb1550_devices() : db1550_devices();
 595
 596         swapped = bcsr_read(BCSR_STATUS) &
 597                (id ? BCSR_STATUS_PB1550_SWAPBOOT : BCSR_STATUS_DB1000_SWAPBOOT);
 598         db1x_register_norflash(128 << 20, 4, swapped);
 599
 600         return platform_add_devices(db1550_devs, ARRAY_SIZE(db1550_devs));
 601 }