Merge tag 'for-linus-20190706' of git://git.kernel.dk/linux-block
[linux/fpc-iii.git] / drivers / net / ppp / Kconfig
blobbf395df3bb37d9de4da414a5681462d541c679d6
1 # SPDX-License-Identifier: GPL-2.0-only
3 # PPP network device configuration
6 config PPP
7         tristate "PPP (point-to-point protocol) support"
8         select SLHC
9         ---help---
10           PPP (Point to Point Protocol) is a newer and better SLIP.  It serves
11           the same purpose: sending Internet traffic over telephone (and other
12           serial) lines.  Ask your access provider if they support it, because
13           otherwise you can't use it; most Internet access providers these
14           days support PPP rather than SLIP.
16           To use PPP, you need an additional program called pppd as described
17           in the PPP-HOWTO, available at
18           <http://www.tldp.org/docs.html#howto>.  Make sure that you have
19           the version of pppd recommended in <file:Documentation/Changes>.
20           The PPP option enlarges your kernel by about 16 KB.
22           There are actually two versions of PPP: the traditional PPP for
23           asynchronous lines, such as regular analog phone lines, and
24           synchronous PPP which can be used over digital ISDN lines for
25           example.  If you want to use PPP over phone lines or other
26           asynchronous serial lines, you need to say Y (or M) here and also to
27           the next option, "PPP support for async serial ports".  For PPP over
28           synchronous lines, you should say Y (or M) here and to "Support
29           synchronous PPP", below.
31           If you said Y to "Version information on all symbols" above, then
32           you cannot compile the PPP driver into the kernel; you can then only
33           compile it as a module. To compile this driver as a module, choose M
34           here. The module will be called ppp_generic.
36 if PPP
38 config PPP_BSDCOMP
39         tristate "PPP BSD-Compress compression"
40         depends on PPP
41         ---help---
42           Support for the BSD-Compress compression method for PPP, which uses
43           the LZW compression method to compress each PPP packet before it is
44           sent over the wire. The machine at the other end of the PPP link
45           (usually your ISP) has to support the BSD-Compress compression
46           method as well for this to be useful. Even if they don't support it,
47           it is safe to say Y here.
49           The PPP Deflate compression method ("PPP Deflate compression",
50           above) is preferable to BSD-Compress, because it compresses better
51           and is patent-free.
53           Note that the BSD compression code will always be compiled as a
54           module; it is called bsd_comp and will show up in the directory
55           modules once you have said "make modules". If unsure, say N.
57 config PPP_DEFLATE
58         tristate "PPP Deflate compression"
59         depends on PPP
60         select ZLIB_INFLATE
61         select ZLIB_DEFLATE
62         ---help---
63           Support for the Deflate compression method for PPP, which uses the
64           Deflate algorithm (the same algorithm that gzip uses) to compress
65           each PPP packet before it is sent over the wire.  The machine at the
66           other end of the PPP link (usually your ISP) has to support the
67           Deflate compression method as well for this to be useful.  Even if
68           they don't support it, it is safe to say Y here.
70           To compile this driver as a module, choose M here.
72 config PPP_FILTER
73         bool "PPP filtering"
74         depends on PPP
75         ---help---
76           Say Y here if you want to be able to filter the packets passing over
77           PPP interfaces.  This allows you to control which packets count as
78           activity (i.e. which packets will reset the idle timer or bring up
79           a demand-dialed link) and which packets are to be dropped entirely.
80           You need to say Y here if you wish to use the pass-filter and
81           active-filter options to pppd.
83           If unsure, say N.
85 config PPP_MPPE
86         tristate "PPP MPPE compression (encryption)"
87         depends on PPP
88         select CRYPTO
89         select CRYPTO_SHA1
90         select CRYPTO_ARC4
91         select CRYPTO_ECB
92         ---help---
93           Support for the MPPE Encryption protocol, as employed by the
94           Microsoft Point-to-Point Tunneling Protocol.
96           See http://pptpclient.sourceforge.net/ for information on
97           configuring PPTP clients and servers to utilize this method.
99 config PPP_MULTILINK
100         bool "PPP multilink support"
101         depends on PPP
102         ---help---
103           PPP multilink is a protocol (defined in RFC 1990) which allows you
104           to combine several (logical or physical) lines into one logical PPP
105           connection, so that you can utilize your full bandwidth.
107           This has to be supported at the other end as well and you need a
108           version of the pppd daemon which understands the multilink protocol.
110           If unsure, say N.
112 config PPPOATM
113         tristate "PPP over ATM"
114         depends on ATM && PPP
115         ---help---
116           Support PPP (Point to Point Protocol) encapsulated in ATM frames.
117           This implementation does not yet comply with section 8 of RFC2364,
118           which can lead to bad results if the ATM peer loses state and
119           changes its encapsulation unilaterally.
121 config PPPOE
122         tristate "PPP over Ethernet"
123         depends on PPP
124         ---help---
125           Support for PPP over Ethernet.
127           This driver requires the latest version of pppd from the CVS
128           repository at cvs.samba.org.  Alternatively, see the
129           RoaringPenguin package (<http://www.roaringpenguin.com/pppoe>)
130           which contains instruction on how to use this driver (under
131           the heading "Kernel mode PPPoE").
133 config PPTP
134         tristate "PPP over IPv4 (PPTP)"
135         depends on PPP && NET_IPGRE_DEMUX
136         ---help---
137           Support for PPP over IPv4.(Point-to-Point Tunneling Protocol)
139           This driver requires pppd plugin to work in client mode or
140           modified pptpd (poptop) to work in server mode.
141           See http://accel-pptp.sourceforge.net/ for information how to
142           utilize this module.
144 config PPPOL2TP
145         tristate "PPP over L2TP"
146         depends on L2TP && PPP
147         ---help---
148           Support for PPP-over-L2TP socket family. L2TP is a protocol
149           used by ISPs and enterprises to tunnel PPP traffic over UDP
150           tunnels. L2TP is replacing PPTP for VPN uses.
151 if TTY
153 config PPP_ASYNC
154         tristate "PPP support for async serial ports"
155         depends on PPP
156         select CRC_CCITT
157         ---help---
158           Say Y (or M) here if you want to be able to use PPP over standard
159           asynchronous serial ports, such as COM1 or COM2 on a PC.  If you use
160           a modem (not a synchronous or ISDN modem) to contact your ISP, you
161           need this option.
163           To compile this driver as a module, choose M here.
165           If unsure, say Y.
167 config PPP_SYNC_TTY
168         tristate "PPP support for sync tty ports"
169         depends on PPP
170         ---help---
171           Say Y (or M) here if you want to be able to use PPP over synchronous
172           (HDLC) tty devices, such as the SyncLink adapter. These devices
173           are often used for high-speed leased lines like T1/E1.
175           To compile this driver as a module, choose M here.
177 endif # TTY
179 endif # PPP