drivers/net/irda/vlsi_ir.h

   1
   2 /*********************************************************************
   3  *
   4  *      vlsi_ir.h:      VLSI82C147 PCI IrDA controller driver for Linux
   5  *
   6  *      Version:        0.5
   7  *
   8  *      Copyright (c) 2001-2003 Martin Diehl
   9  *
  10  *      This program is free software; you can redistribute it and/or
  11  *      modify it under the terms of the GNU General Public License as
  12  *      published by the Free Software Foundation; either version 2 of
  13  *      the License, or (at your option) any later version.
  14  *
  15  *      This program is distributed in the hope that it will be useful,
  16  *      but WITHOUT ANY WARRANTY; without even the implied warranty of
  17  *      MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
  18  *      GNU General Public License for more details.
  19  *
  20  *      You should have received a copy of the GNU General Public License
  21  *      along with this program; if not, write to the Free Software
  22  *      Foundation, Inc., 59 Temple Place, Suite 330, Boston,
  23  *      MA 02111-1307 USA
  24  *
  25  ********************************************************************/
  26
  27 #ifndef IRDA_VLSI_FIR_H
  28 #define IRDA_VLSI_FIR_H
  29
  30 /* ================================================================
  31  * compatibility stuff
  32  */
  33
  34 /* definitions not present in pci_ids.h */
  35
  36 #ifndef PCI_CLASS_WIRELESS_IRDA
  37 #define PCI_CLASS_WIRELESS_IRDA         0x0d00
  38 #endif
  39
  40 #ifndef PCI_CLASS_SUBCLASS_MASK
  41 #define PCI_CLASS_SUBCLASS_MASK         0xffff
  42 #endif
  43
  44 /* ================================================================ */
  45
  46 /* non-standard PCI registers */
  47
  48 enum vlsi_pci_regs {
  49         VLSI_PCI_CLKCTL         = 0x40,         /* chip clock input control */
  50         VLSI_PCI_MSTRPAGE       = 0x41,         /* addr [31:24] for all busmaster cycles */
  51         VLSI_PCI_IRMISC         = 0x42          /* mainly legacy UART related */
  52 };
  53
  54 /* ------------------------------------------ */
  55
  56 /* VLSI_PCI_CLKCTL: Clock Control Register (u8, rw) */
  57
  58 /* Three possible clock sources: either on-chip 48MHz PLL or
  59  * external clock applied to EXTCLK pin. External clock may
  60  * be either 48MHz or 40MHz, which is indicated by XCKSEL.
  61  * CLKSTP controls whether the selected clock source gets
  62  * connected to the IrDA block.
  63  *
  64  * On my HP OB-800 the BIOS sets external 40MHz clock as source
  65  * when IrDA enabled and I've never detected any PLL lock success.
  66  * Apparently the 14.3...MHz OSC input required for the PLL to work
  67  * is not connected and the 40MHz EXTCLK is provided externally.
  68  * At least this is what makes the driver working for me.
  69  */
  70
  71 enum vlsi_pci_clkctl {
  72
  73         /* PLL control */
  74
  75         CLKCTL_PD_INV           = 0x04,         /* PD#: inverted power down signal,
  76                                                  * i.e. PLL is powered, if PD_INV set */
  77         CLKCTL_LOCK             = 0x40,         /* (ro) set, if PLL is locked */
  78
  79         /* clock source selection */
  80
  81         CLKCTL_EXTCLK           = 0x20,         /* set to select external clock input, not PLL */
  82         CLKCTL_XCKSEL           = 0x10,         /* set to indicate EXTCLK is 40MHz, not 48MHz */
  83
  84         /* IrDA block control */
  85
  86         CLKCTL_CLKSTP           = 0x80,         /* set to disconnect from selected clock source */
  87         CLKCTL_WAKE             = 0x08          /* set to enable wakeup feature: whenever IR activity
  88                                                  * is detected, PD_INV gets set(?) and CLKSTP cleared */
  89 };
  90
  91 /* ------------------------------------------ */
  92
  93 /* VLSI_PCI_MSTRPAGE: Master Page Register (u8, rw) and busmastering stuff */
  94
  95 #define DMA_MASK_USED_BY_HW     0xffffffff
  96 #define DMA_MASK_MSTRPAGE       0x00ffffff
  97 #define MSTRPAGE_VALUE          (DMA_MASK_MSTRPAGE >> 24)
  98
  99         /* PCI busmastering is somewhat special for this guy - in short:
 100          *
 101          * We select to operate using fixed MSTRPAGE=0, use ISA DMA
 102          * address restrictions to make the PCI BM api aware of this,
 103          * but ensure the hardware is dealing with real 32bit access.
 104          *
 105          * In detail:
 106          * The chip executes normal 32bit busmaster cycles, i.e.
 107          * drives all 32 address lines. These addresses however are
 108          * composed of [0:23] taken from various busaddr-pointers
 109          * and [24:31] taken from the MSTRPAGE register in the VLSI82C147
 110          * config space. Therefore _all_ busmastering must be
 111          * targeted to/from one single 16MB (busaddr-) superpage!
 112          * The point is to make sure all the allocations for memory
 113          * locations with busmaster access (ring descriptors, buffers)
 114          * are indeed bus-mappable to the same 16MB range (for x86 this
 115          * means they must reside in the same 16MB physical memory address
 116          * range). The only constraint we have which supports "several objects
 117          * mappable to common 16MB range" paradigma, is the old ISA DMA
 118          * restriction to the first 16MB of physical address range.
 119          * Hence the approach here is to enable PCI busmaster support using
 120          * the correct 32bit dma-mask used by the chip. Afterwards the device's
 121          * dma-mask gets restricted to 24bit, which must be honoured somehow by
 122          * all allocations for memory areas to be exposed to the chip ...
 123          *
 124          * Note:
 125          * Don't be surprised to get "Setting latency timer..." messages every
 126          * time when PCI busmastering is enabled for the chip.
 127          * The chip has its PCI latency timer RO fixed at 0 - which is not a
 128          * problem here, because it is never requesting _burst_ transactions.
 129          */
 130
 131 /* ------------------------------------------ */
 132
 133 /* VLSI_PCIIRMISC: IR Miscellaneous Register (u8, rw) */
 134
 135 /* legacy UART emulation - not used by this driver - would require:
 136  * (see below for some register-value definitions)
 137  *
 138  *      - IRMISC_UARTEN must be set to enable UART address decoding
 139  *      - IRMISC_UARTSEL configured
 140  *      - IRCFG_MASTER must be cleared
 141  *      - IRCFG_SIR must be set
 142  *      - IRENABLE_PHYANDCLOCK must be asserted 0->1 (and hence IRENABLE_SIR_ON)
 143  */
 144
 145 enum vlsi_pci_irmisc {
 146
 147         /* IR transceiver control */
 148
 149         IRMISC_IRRAIL           = 0x40,         /* (ro?) IR rail power indication (and control?)
 150                                                  * 0=3.3V / 1=5V. Probably set during power-on?
 151                                                  * unclear - not touched by driver */
 152         IRMISC_IRPD             = 0x08,         /* transceiver power down, if set */
 153
 154         /* legacy UART control */
 155
 156         IRMISC_UARTTST          = 0x80,         /* UART test mode - "always write 0" */
 157         IRMISC_UARTEN           = 0x04,         /* enable UART address decoding */
 158
 159         /* bits [1:0] IRMISC_UARTSEL to select legacy UART address */
 160
 161         IRMISC_UARTSEL_3f8      = 0x00,
 162         IRMISC_UARTSEL_2f8      = 0x01,
 163         IRMISC_UARTSEL_3e8      = 0x02,
 164         IRMISC_UARTSEL_2e8      = 0x03
 165 };
 166
 167 /* ================================================================ */
 168
 169 /* registers mapped to 32 byte PCI IO space */
 170
 171 /* note: better access all registers at the indicated u8/u16 size
 172  *       although some of them contain only 1 byte of information.
 173  *       some of them (particaluarly PROMPT and IRCFG) ignore
 174  *       access when using the wrong addressing mode!
 175  */
 176
 177 enum vlsi_pio_regs {
 178         VLSI_PIO_IRINTR         = 0x00,         /* interrupt enable/request (u8, rw) */
 179         VLSI_PIO_RINGPTR        = 0x02,         /* rx/tx ring pointer (u16, ro) */
 180         VLSI_PIO_RINGBASE       = 0x04,         /* [23:10] of ring address (u16, rw) */
 181         VLSI_PIO_RINGSIZE       = 0x06,         /* rx/tx ring size (u16, rw) */
 182         VLSI_PIO_PROMPT         = 0x08,         /* triggers ring processing (u16, wo) */
 183         /* 0x0a-0x0f: reserved / duplicated UART regs */
 184         VLSI_PIO_IRCFG          = 0x10,         /* configuration select (u16, rw) */
 185         VLSI_PIO_SIRFLAG        = 0x12,         /* BOF/EOF for filtered SIR (u16, ro) */
 186         VLSI_PIO_IRENABLE       = 0x14,         /* enable and status register (u16, rw/ro) */
 187         VLSI_PIO_PHYCTL         = 0x16,         /* physical layer current status (u16, ro) */
 188         VLSI_PIO_NPHYCTL        = 0x18,         /* next physical layer select (u16, rw) */
 189         VLSI_PIO_MAXPKT         = 0x1a,         /* [11:0] max len for packet receive (u16, rw) */
 190         VLSI_PIO_RCVBCNT        = 0x1c          /* current receive-FIFO byte count (u16, ro) */
 191         /* 0x1e-0x1f: reserved / duplicated UART regs */
 192 };
 193
 194 /* ------------------------------------------ */
 195
 196 /* VLSI_PIO_IRINTR: Interrupt Register (u8, rw) */
 197
 198 /* enable-bits:
 199  *              1 = enable / 0 = disable
 200  * interrupt condition bits:
 201  *              set according to corresponding interrupt source
 202  *              (regardless of the state of the enable bits)
 203  *              enable bit status indicates whether interrupt gets raised
 204  *              write-to-clear
 205  * note: RPKTINT and TPKTINT behave different in legacy UART mode (which we don't use :-)
 206  */
 207
 208 enum vlsi_pio_irintr {
 209         IRINTR_ACTEN    = 0x80, /* activity interrupt enable */
 210         IRINTR_ACTIVITY = 0x40, /* activity monitor (traffic detected) */
 211         IRINTR_RPKTEN   = 0x20, /* receive packet interrupt enable*/
 212         IRINTR_RPKTINT  = 0x10, /* rx-packet transferred from fifo to memory finished */
 213         IRINTR_TPKTEN   = 0x08, /* transmit packet interrupt enable */
 214         IRINTR_TPKTINT  = 0x04, /* last bit of tx-packet+crc shifted to ir-pulser */
 215         IRINTR_OE_EN    = 0x02, /* UART rx fifo overrun error interrupt enable */
 216         IRINTR_OE_INT   = 0x01  /* UART rx fifo overrun error (read LSR to clear) */
 217 };
 218
 219 /* we use this mask to check whether the (shared PCI) interrupt is ours */
 220
 221 #define IRINTR_INT_MASK         (IRINTR_ACTIVITY|IRINTR_RPKTINT|IRINTR_TPKTINT)
 222
 223 /* ------------------------------------------ */
 224
 225 /* VLSI_PIO_RINGPTR: Ring Pointer Read-Back Register (u16, ro) */
 226
 227 /* _both_ ring pointers are indices relative to the _entire_ rx,tx-ring!
 228  * i.e. the referenced descriptor is located
 229  * at RINGBASE + PTR * sizeof(descr) for rx and tx
 230  * therefore, the tx-pointer has offset MAX_RING_DESCR
 231  */
 232
 233 #define MAX_RING_DESCR          64      /* tx, rx rings may contain up to 64 descr each */
 234
 235 #define RINGPTR_RX_MASK         (MAX_RING_DESCR-1)
 236 #define RINGPTR_TX_MASK         ((MAX_RING_DESCR-1)<<8)
 237
 238 #define RINGPTR_GET_RX(p)       ((p)&RINGPTR_RX_MASK)
 239 #define RINGPTR_GET_TX(p)       (((p)&RINGPTR_TX_MASK)>>8)
 240
 241 /* ------------------------------------------ */
 242
 243 /* VLSI_PIO_RINGBASE: Ring Pointer Base Address Register (u16, ro) */
 244
 245 /* Contains [23:10] part of the ring base (bus-) address
 246  * which must be 1k-alinged. [31:24] is taken from
 247  * VLSI_PCI_MSTRPAGE above.
 248  * The controller initiates non-burst PCI BM cycles to
 249  * fetch and update the descriptors in the ring.
 250  * Once fetched, the descriptor remains cached onchip
 251  * until it gets closed and updated due to the ring
 252  * processing state machine.
 253  * The entire ring area is split in rx and tx areas with each
 254  * area consisting of 64 descriptors of 8 bytes each.
 255  * The rx(tx) ring is located at ringbase+0 (ringbase+64*8).
 256  */
 257
 258 #define BUS_TO_RINGBASE(p)      (((p)>>10)&0x3fff)
 259
 260 /* ------------------------------------------ */
 261
 262 /* VLSI_PIO_RINGSIZE: Ring Size Register (u16, rw) */
 263
 264 /* bit mask to indicate the ring size to be used for rx and tx.
 265  *      possible values         encoded bits
 266  *               4                 0000
 267  *               8                 0001
 268  *              16                 0011
 269  *              32                 0111
 270  *              64                 1111
 271  * located at [15:12] for tx and [11:8] for rx ([7:0] unused)
 272  *
 273  * note: probably a good idea to have IRCFG_MSTR cleared when writing
 274  *       this so the state machines are stopped and the RINGPTR is reset!
 275  */
 276
 277 #define SIZE_TO_BITS(num)               ((((num)-1)>>2)&0x0f)
 278 #define TX_RX_TO_RINGSIZE(tx,rx)        ((SIZE_TO_BITS(tx)<<12)|(SIZE_TO_BITS(rx)<<8))
 279 #define RINGSIZE_TO_RXSIZE(rs)          ((((rs)&0x0f00)>>6)+4)
 280 #define RINGSIZE_TO_TXSIZE(rs)          ((((rs)&0xf000)>>10)+4)
 281
 282
 283 /* ------------------------------------------ */
 284
 285 /* VLSI_PIO_PROMPT: Ring Prompting Register (u16, write-to-start) */
 286
 287 /* writing any value kicks the ring processing state machines
 288  * for both tx, rx rings as follows:
 289  *      - active rings (currently owning an active descriptor)
 290  *        ignore the prompt and continue
 291  *      - idle rings fetch the next descr from the ring and start
 292  *        their processing
 293  */
 294
 295 /* ------------------------------------------ */
 296
 297 /* VLSI_PIO_IRCFG: IR Config Register (u16, rw) */
 298
 299 /* notes:
 300  *      - not more than one SIR/MIR/FIR bit must be set at any time
 301  *      - SIR, MIR, FIR and CRC16 select the configuration which will
 302  *        be applied on next 0->1 transition of IRENABLE_PHYANDCLOCK (see below).
 303  *      - besides allowing the PCI interface to execute busmaster cycles
 304  *        and therefore the ring SM to operate, the MSTR bit has side-effects:
 305  *        when MSTR is cleared, the RINGPTR's get reset and the legacy UART mode
 306  *        (in contrast to busmaster access mode) gets enabled.
 307  *      - clearing ENRX or setting ENTX while data is received may stall the
 308  *        receive fifo until ENRX reenabled _and_ another packet arrives
 309  *      - SIRFILT means the chip performs the required unwrapping of hardware
 310  *        headers (XBOF's, BOF/EOF) and un-escaping in the _receive_ direction.
 311  *        Only the resulting IrLAP payload is copied to the receive buffers -
 312  *        but with the 16bit FCS still encluded. Question remains, whether it
 313  *        was already checked or we should do it before passing the packet to IrLAP?
 314  */
 315
 316 enum vlsi_pio_ircfg {
 317         IRCFG_LOOP      = 0x4000,       /* enable loopback test mode */
 318         IRCFG_ENTX      = 0x1000,       /* transmit enable */
 319         IRCFG_ENRX      = 0x0800,       /* receive enable */
 320         IRCFG_MSTR      = 0x0400,       /* master enable */
 321         IRCFG_RXANY     = 0x0200,       /* receive any packet */
 322         IRCFG_CRC16     = 0x0080,       /* 16bit (not 32bit) CRC select for MIR/FIR */
 323         IRCFG_FIR       = 0x0040,       /* FIR 4PPM encoding mode enable */
 324         IRCFG_MIR       = 0x0020,       /* MIR HDLC encoding mode enable */
 325         IRCFG_SIR       = 0x0010,       /* SIR encoding mode enable */
 326         IRCFG_SIRFILT   = 0x0008,       /* enable SIR decode filter (receiver unwrapping) */
 327         IRCFG_SIRTEST   = 0x0004,       /* allow SIR decode filter when not in SIR mode */
 328         IRCFG_TXPOL     = 0x0002,       /* invert tx polarity when set */
 329         IRCFG_RXPOL     = 0x0001        /* invert rx polarity when set */
 330 };
 331
 332 /* ------------------------------------------ */
 333
 334 /* VLSI_PIO_SIRFLAG: SIR Flag Register (u16, ro) */
 335
 336 /* register contains hardcoded BOF=0xc0 at [7:0] and EOF=0xc1 at [15:8]
 337  * which is used for unwrapping received frames in SIR decode-filter mode
 338  */
 339
 340 /* ------------------------------------------ */
 341
 342 /* VLSI_PIO_IRENABLE: IR Enable Register (u16, rw/ro) */
 343
 344 /* notes:
 345  *      - IREN acts as gate for latching the configured IR mode information
 346  *        from IRCFG and IRPHYCTL when IREN=reset and applying them when
 347  *        IREN gets set afterwards.
 348  *      - ENTXST reflects IRCFG_ENTX
 349  *      - ENRXST = IRCFG_ENRX && (!IRCFG_ENTX || IRCFG_LOOP)
 350  */
 351
 352 enum vlsi_pio_irenable {
 353         IRENABLE_PHYANDCLOCK    = 0x8000,  /* enable IR phy and gate the mode config (rw) */
 354         IRENABLE_CFGER          = 0x4000,  /* mode configuration error (ro) */
 355         IRENABLE_FIR_ON         = 0x2000,  /* FIR on status (ro) */
 356         IRENABLE_MIR_ON         = 0x1000,  /* MIR on status (ro) */
 357         IRENABLE_SIR_ON         = 0x0800,  /* SIR on status (ro) */
 358         IRENABLE_ENTXST         = 0x0400,  /* transmit enable status (ro) */
 359         IRENABLE_ENRXST         = 0x0200,  /* Receive enable status (ro) */
 360         IRENABLE_CRC16_ON       = 0x0100   /* 16bit (not 32bit) CRC enabled status (ro) */
 361 };
 362
 363 #define   IRENABLE_MASK     0xff00  /* Read mask */
 364
 365 /* ------------------------------------------ */
 366
 367 /* VLSI_PIO_PHYCTL: IR Physical Layer Current Control Register (u16, ro) */
 368
 369 /* read-back of the currently applied physical layer status.
 370  * applied from VLSI_PIO_NPHYCTL at rising edge of IRENABLE_PHYANDCLOCK
 371  * contents identical to VLSI_PIO_NPHYCTL (see below)
 372  */
 373
 374 /* ------------------------------------------ */
 375
 376 /* VLSI_PIO_NPHYCTL: IR Physical Layer Next Control Register (u16, rw) */
 377
 378 /* latched during IRENABLE_PHYANDCLOCK=0 and applied at 0-1 transition
 379  *
 380  * consists of BAUD[15:10], PLSWID[9:5] and PREAMB[4:0] bits defined as follows:
 381  *
 382  * SIR-mode:    BAUD = (115.2kHz / baudrate) - 1
 383  *              PLSWID = (pulsetime * freq / (BAUD+1)) - 1
 384  *                      where pulsetime is the requested IrPHY pulse width
 385  *                      and freq is 8(16)MHz for 40(48)MHz primary input clock
 386  *              PREAMB: don't care for SIR
 387  *
 388  *              The nominal SIR pulse width is 3/16 bit time so we have PLSWID=12
 389  *              fixed for all SIR speeds at 40MHz input clock (PLSWID=24 at 48MHz).
 390  *              IrPHY also allows shorter pulses down to the nominal pulse duration
 391  *              at 115.2kbaud (minus some tolerance) which is 1.41 usec.
 392  *              Using the expression PLSWID = 12/(BAUD+1)-1 (multiplied by two for 48MHz)
 393  *              we get the minimum acceptable PLSWID values according to the VLSI
 394  *              specification, which provides 1.5 usec pulse width for all speeds (except
 395  *              for 2.4kbaud getting 6usec). This is fine with IrPHY v1.3 specs and
 396  *              reduces the transceiver power which drains the battery. At 9.6kbaud for
 397  *              example this amounts to more than 90% battery power saving!
 398  *
 399  * MIR-mode:    BAUD = 0
 400  *              PLSWID = 9(10) for 40(48) MHz input clock
 401  *                      to get nominal MIR pulse width
 402  *              PREAMB = 1
 403  *
 404  * FIR-mode:    BAUD = 0
 405  *              PLSWID: don't care
 406  *              PREAMB = 15
 407  */
 408
 409 #define PHYCTL_BAUD_SHIFT       10
 410 #define PHYCTL_BAUD_MASK        0xfc00
 411 #define PHYCTL_PLSWID_SHIFT     5
 412 #define PHYCTL_PLSWID_MASK      0x03e0
 413 #define PHYCTL_PREAMB_SHIFT     0
 414 #define PHYCTL_PREAMB_MASK      0x001f
 415
 416 #define PHYCTL_TO_BAUD(bwp)     (((bwp)&PHYCTL_BAUD_MASK)>>PHYCTL_BAUD_SHIFT)
 417 #define PHYCTL_TO_PLSWID(bwp)   (((bwp)&PHYCTL_PLSWID_MASK)>>PHYCTL_PLSWID_SHIFT)
 418 #define PHYCTL_TO_PREAMB(bwp)   (((bwp)&PHYCTL_PREAMB_MASK)>>PHYCTL_PREAMB_SHIFT)
 419
 420 #define BWP_TO_PHYCTL(b,w,p)    ((((b)<<PHYCTL_BAUD_SHIFT)&PHYCTL_BAUD_MASK) \
 421                                  | (((w)<<PHYCTL_PLSWID_SHIFT)&PHYCTL_PLSWID_MASK) \
 422                                  | (((p)<<PHYCTL_PREAMB_SHIFT)&PHYCTL_PREAMB_MASK))
 423
 424 #define BAUD_BITS(br)           ((115200/(br))-1)
 425
 426 static inline unsigned
 427 calc_width_bits(unsigned baudrate, unsigned widthselect, unsigned clockselect)
 428 {
 429         unsigned        tmp;
 430
 431         if (widthselect)        /* nominal 3/16 puls width */
 432                 return (clockselect) ? 12 : 24;
 433
 434         tmp = ((clockselect) ? 12 : 24) / (BAUD_BITS(baudrate)+1);
 435
 436         /* intermediate result of integer division needed here */
 437
 438         return (tmp>0) ? (tmp-1) : 0;
 439 }
 440
 441 #define PHYCTL_SIR(br,ws,cs)    BWP_TO_PHYCTL(BAUD_BITS(br),calc_width_bits((br),(ws),(cs)),0)
 442 #define PHYCTL_MIR(cs)          BWP_TO_PHYCTL(0,((cs)?9:10),1)
 443 #define PHYCTL_FIR              BWP_TO_PHYCTL(0,0,15)
 444
 445 /* quite ugly, I know. But implementing these calculations here avoids
 446  * having magic numbers in the code and allows some playing with pulsewidths
 447  * without risk to violate the standards.
 448  * FWIW, here is the table for reference:
 449  *
 450  * baudrate     BAUD    min-PLSWID      nom-PLSWID      PREAMB
 451  *     2400       47       0(0)            12(24)          0
 452  *     9600       11       0(0)            12(24)          0
 453  *    19200        5       1(2)            12(24)          0
 454  *    38400        2       3(6)            12(24)          0
 455  *    57600        1       5(10)           12(24)          0
 456  *   115200        0      11(22)           12(24)          0
 457  *      MIR        0        -               9(10)          1
 458  *      FIR        0        -               0             15
 459  *
 460  * note: x(y) means x-value for 40MHz / y-value for 48MHz primary input clock
 461  */
 462
 463 /* ------------------------------------------ */
 464
 465
 466 /* VLSI_PIO_MAXPKT: Maximum Packet Length register (u16, rw) */
 467
 468 /* maximum acceptable length for received packets */
 469
 470 /* hw imposed limitation - register uses only [11:0] */
 471 #define MAX_PACKET_LENGTH       0x0fff
 472
 473 /* IrLAP I-field (apparently not defined elsewhere) */
 474 #define IRDA_MTU                2048
 475
 476 /* complete packet consists of A(1)+C(1)+I(<=IRDA_MTU) */
 477 #define IRLAP_SKB_ALLOCSIZE     (1+1+IRDA_MTU)
 478
 479 /* the buffers we use to exchange frames with the hardware need to be
 480  * larger than IRLAP_SKB_ALLOCSIZE because we may have up to 4 bytes FCS
 481  * appended and, in SIR mode, a lot of frame wrapping bytes. The worst
 482  * case appears to be a SIR packet with I-size==IRDA_MTU and all bytes
 483  * requiring to be escaped to provide transparency. Furthermore, the peer
 484  * might ask for quite a number of additional XBOFs:
 485  *      up to 115+48 XBOFS               163
 486  *      regular BOF                        1
 487  *      A-field                            1
 488  *      C-field                            1
 489  *      I-field, IRDA_MTU, all escaped  4096
 490  *      FCS (16 bit at SIR, escaped)       4
 491  *      EOF                                1
 492  * AFAICS nothing in IrLAP guarantees A/C field not to need escaping
 493  * (f.e. 0xc0/0xc1 - i.e. BOF/EOF - are legal values there) so in the
 494  * worst case we have 4269 bytes total frame size.
 495  * However, the VLSI uses 12 bits only for all buffer length values,
 496  * which limits the maximum useable buffer size <= 4095.
 497  * Note this is not a limitation in the receive case because we use
 498  * the SIR filtering mode where the hw unwraps the frame and only the
 499  * bare packet+fcs is stored into the buffer - in contrast to the SIR
 500  * tx case where we have to pass frame-wrapped packets to the hw.
 501  * If this would ever become an issue in real life, the only workaround
 502  * I see would be using the legacy UART emulation in SIR mode.
 503  */
 504
 505 #define XFER_BUF_SIZE           MAX_PACKET_LENGTH
 506
 507 /* ------------------------------------------ */
 508
 509 /* VLSI_PIO_RCVBCNT: Receive Byte Count Register (u16, ro) */
 510
 511 /* receive packet counter gets incremented on every non-filtered
 512  * byte which was put in the receive fifo and reset for each
 513  * new packet. Used to decide whether we are just in the middle
 514  * of receiving
 515  */
 516
 517 /* better apply the [11:0] mask when reading, as some docs say the
 518  * reserved [15:12] would return 1 when reading - which is wrong AFAICS
 519  */
 520 #define RCVBCNT_MASK    0x0fff
 521
 522 /******************************************************************/
 523
 524 /* descriptors for rx/tx ring
 525  *
 526  * accessed by hardware - don't change!
 527  *
 528  * the descriptor is owned by hardware, when the ACTIVE status bit
 529  * is set and nothing (besides reading status to test the bit)
 530  * shall be done. The bit gets cleared by hw, when the descriptor
 531  * gets closed. Premature reaping of descriptors owned be the chip
 532  * can be achieved by disabling IRCFG_MSTR
 533  *
 534  * Attention: Writing addr overwrites status!
 535  *
 536  * ### FIXME: depends on endianess (but there ain't no non-i586 ob800 ;-)
 537  */
 538
 539 struct ring_descr_hw {
 540         volatile __le16 rd_count;       /* tx/rx count [11:0] */
 541         __le16          reserved;
 542         union {
 543                 __le32  addr;           /* [23:0] of the buffer's busaddress */
 544                 struct {
 545                         u8              addr_res[3];
 546                         volatile u8     status;         /* descriptor status */
 547                 } __packed rd_s;
 548         } __packed rd_u;
 549 } __packed;
 550
 551 #define rd_addr         rd_u.addr
 552 #define rd_status       rd_u.rd_s.status
 553
 554 /* ring descriptor status bits */
 555
 556 #define RD_ACTIVE               0x80    /* descriptor owned by hw (both TX,RX) */
 557
 558 /* TX ring descriptor status */
 559
 560 #define RD_TX_DISCRC            0x40    /* do not send CRC (for SIR) */
 561 #define RD_TX_BADCRC            0x20    /* force a bad CRC */
 562 #define RD_TX_PULSE             0x10    /* send indication pulse after this frame (MIR/FIR) */
 563 #define RD_TX_FRCEUND           0x08    /* force underrun */
 564 #define RD_TX_CLRENTX           0x04    /* clear ENTX after this frame */
 565 #define RD_TX_UNDRN             0x01    /* TX fifo underrun (probably PCI problem) */
 566
 567 /* RX ring descriptor status */
 568
 569 #define RD_RX_PHYERR            0x40    /* physical encoding error */
 570 #define RD_RX_CRCERR            0x20    /* CRC error (MIR/FIR) */
 571 #define RD_RX_LENGTH            0x10    /* frame exceeds buffer length */
 572 #define RD_RX_OVER              0x08    /* RX fifo overrun (probably PCI problem) */
 573 #define RD_RX_SIRBAD            0x04    /* EOF missing: BOF follows BOF (SIR, filtered) */
 574
 575 #define RD_RX_ERROR             0x7c    /* any error in received frame */
 576
 577 /* the memory required to hold the 2 descriptor rings */
 578 #define HW_RING_AREA_SIZE       (2 * MAX_RING_DESCR * sizeof(struct ring_descr_hw))
 579
 580 /******************************************************************/
 581
 582 /* sw-ring descriptors consists of a bus-mapped transfer buffer with
 583  * associated skb and a pointer to the hw entry descriptor
 584  */
 585
 586 struct ring_descr {
 587         struct ring_descr_hw    *hw;
 588         struct sk_buff          *skb;
 589         void                    *buf;
 590 };
 591
 592 /* wrappers for operations on hw-exposed ring descriptors
 593  * access to the hw-part of the descriptors must use these.
 594  */
 595
 596 static inline int rd_is_active(struct ring_descr *rd)
 597 {
 598         return (rd->hw->rd_status & RD_ACTIVE) != 0;
 599 }
 600
 601 static inline void rd_activate(struct ring_descr *rd)
 602 {
 603         rd->hw->rd_status |= RD_ACTIVE;
 604 }
 605
 606 static inline void rd_set_status(struct ring_descr *rd, u8 s)
 607 {
 608         rd->hw->rd_status = s;   /* may pass ownership to the hardware */
 609 }
 610
 611 static inline void rd_set_addr_status(struct ring_descr *rd, dma_addr_t a, u8 s)
 612 {
 613         /* order is important for two reasons:
 614          *  - overlayed: writing addr overwrites status
 615          *  - we want to write status last so we have valid address in
 616          *    case status has RD_ACTIVE set
 617          */
 618
 619         if ((a & ~DMA_MASK_MSTRPAGE)>>24 != MSTRPAGE_VALUE) {
 620                 IRDA_ERROR("%s: pci busaddr inconsistency!\n", __func__);
 621                 dump_stack();
 622                 return;
 623         }
 624
 625         a &= DMA_MASK_MSTRPAGE;  /* clear highbyte to make sure we won't write
 626                                   * to status - just in case MSTRPAGE_VALUE!=0
 627                                   */
 628         rd->hw->rd_addr = cpu_to_le32(a);
 629         wmb();
 630         rd_set_status(rd, s);    /* may pass ownership to the hardware */
 631 }
 632
 633 static inline void rd_set_count(struct ring_descr *rd, u16 c)
 634 {
 635         rd->hw->rd_count = cpu_to_le16(c);
 636 }
 637
 638 static inline u8 rd_get_status(struct ring_descr *rd)
 639 {
 640         return rd->hw->rd_status;
 641 }
 642
 643 static inline dma_addr_t rd_get_addr(struct ring_descr *rd)
 644 {
 645         dma_addr_t      a;
 646
 647         a = le32_to_cpu(rd->hw->rd_addr);
 648         return (a & DMA_MASK_MSTRPAGE) | (MSTRPAGE_VALUE << 24);
 649 }
 650
 651 static inline u16 rd_get_count(struct ring_descr *rd)
 652 {
 653         return le16_to_cpu(rd->hw->rd_count);
 654 }
 655
 656 /******************************************************************/
 657
 658 /* sw descriptor rings for rx, tx:
 659  *
 660  * operations follow producer-consumer paradigm, with the hw
 661  * in the middle doing the processing.
 662  * ring size must be power of two.
 663  *
 664  * producer advances r->tail after inserting for processing
 665  * consumer advances r->head after removing processed rd
 666  * ring is empty if head==tail / full if (tail+1)==head
 667  */
 668
 669 struct vlsi_ring {
 670         struct pci_dev          *pdev;
 671         int                     dir;
 672         unsigned                len;
 673         unsigned                size;
 674         unsigned                mask;
 675         atomic_t                head, tail;
 676         struct ring_descr       *rd;
 677 };
 678
 679 /* ring processing helpers */
 680
 681 static inline struct ring_descr *ring_last(struct vlsi_ring *r)
 682 {
 683         int t;
 684
 685         t = atomic_read(&r->tail) & r->mask;
 686         return (((t+1) & r->mask) == (atomic_read(&r->head) & r->mask)) ? NULL : &r->rd[t];
 687 }
 688
 689 static inline struct ring_descr *ring_put(struct vlsi_ring *r)
 690 {
 691         atomic_inc(&r->tail);
 692         return ring_last(r);
 693 }
 694
 695 static inline struct ring_descr *ring_first(struct vlsi_ring *r)
 696 {
 697         int h;
 698
 699         h = atomic_read(&r->head) & r->mask;
 700         return (h == (atomic_read(&r->tail) & r->mask)) ? NULL : &r->rd[h];
 701 }
 702
 703 static inline struct ring_descr *ring_get(struct vlsi_ring *r)
 704 {
 705         atomic_inc(&r->head);
 706         return ring_first(r);
 707 }
 708
 709 /******************************************************************/
 710
 711 /* our private compound VLSI-PCI-IRDA device information */
 712
 713 typedef struct vlsi_irda_dev {
 714         struct pci_dev          *pdev;
 715
 716         struct irlap_cb         *irlap;
 717
 718         struct qos_info         qos;
 719
 720         unsigned                mode;
 721         int                     baud, new_baud;
 722
 723         dma_addr_t              busaddr;
 724         void                    *virtaddr;
 725         struct vlsi_ring        *tx_ring, *rx_ring;
 726
 727         struct timeval          last_rx;
 728
 729         spinlock_t              lock;
 730         struct mutex            mtx;
 731
 732         u8                      resume_ok;
 733         struct proc_dir_entry   *proc_entry;
 734
 735 } vlsi_irda_dev_t;
 736
 737 /********************************************************/
 738
 739 /* the remapped error flags we use for returning from frame
 740  * post-processing in vlsi_process_tx/rx() after it was completed
 741  * by the hardware. These functions either return the >=0 number
 742  * of transferred bytes in case of success or the negative (-)
 743  * of the or'ed error flags.
 744  */
 745
 746 #define VLSI_TX_DROP            0x0001
 747 #define VLSI_TX_FIFO            0x0002
 748
 749 #define VLSI_RX_DROP            0x0100
 750 #define VLSI_RX_OVER            0x0200
 751 #define VLSI_RX_LENGTH          0x0400
 752 #define VLSI_RX_FRAME           0x0800
 753 #define VLSI_RX_CRC             0x1000
 754
 755 /********************************************************/
 756
 757 #endif /* IRDA_VLSI_FIR_H */
 758