| blob | d92b705e7917db2bd192d331fa58a1d99a28f743 |
1 Renesas R-Car sound
3 =============================================
4 * Modules
5 =============================================
7 Renesas R-Car and RZ/G sound is constructed from below modules
8 (for Gen2 or later)
10 SCU : Sampling Rate Converter Unit
11 - SRC : Sampling Rate Converter
12 - CMD
13 - CTU : Channel Transfer Unit
14 - MIX : Mixer
15 - DVC : Digital Volume and Mute Function
16 SSIU : Serial Sound Interface Unit
17 SSI : Serial Sound Interface
19 See detail of each module's channels, connection, limitation on datasheet
21 =============================================
22 * Multi channel
23 =============================================
25 Multi channel is supported by Multi-SSI, or TDM-SSI.
27 Multi-SSI : 6ch case, you can use stereo x 3 SSI
28 TDM-SSI : 6ch case, you can use TDM
30 =============================================
31 * Enable/Disable each modules
32 =============================================
34 See datasheet to check SRC/CTU/MIX/DVC connect-limitation.
35 DT controls enabling/disabling module.
36 ${LINUX}/arch/arm/boot/dts/r8a7790-lager.dts can be good example.
37 This is example of
39 Playback: [MEM] -> [SRC2] -> [DVC0] -> [SSIU0/SSI0] -> [codec]
40 Capture: [MEM] <- [DVC1] <- [SRC3] <- [SSIU1/SSI1] <- [codec]
42 &rcar_sound {
43 ...
44 rcar_sound,dai {
45 dai0 {
46 playback = <&ssi0 &src2 &dvc0>;
47 capture = <&ssi1 &src3 &dvc1>;
48 };
49 };
50 };
52 You can use below.
53 ${LINUX}/arch/arm/boot/dts/r8a7790.dts can be good example.
55 &src0 &ctu00 &mix0 &dvc0 &ssi0
56 &src1 &ctu01 &mix1 &dvc1 &ssi1
57 &src2 &ctu02 &ssi2
58 &src3 &ctu03 &ssi3
59 &src4 &ssi4
60 &src5 &ctu10 &ssi5
61 &src6 &ctu11 &ssi6
62 &src7 &ctu12 &ssi7
63 &src8 &ctu13 &ssi8
64 &src9 &ssi9
66 =============================================
67 * SRC (Sampling Rate Converter)
68 =============================================
70 [xx]Hz [yy]Hz
71 ------> [SRC] ------>
73 SRC can convert [xx]Hz to [yy]Hz. Then, it has below 2 modes
75 Asynchronous mode: input data / output data are based on different clocks.
76 you can use this mode on Playback / Capture
77 Synchronous mode: input data / output data are based on same clocks.
78 This mode will be used if system doesn't have its input clock,
79 for example digital TV case.
80 you can use this mode on Playback
82 ------------------
83 ** Asynchronous mode
84 ------------------
86 You need to use "simple-scu-audio-card" sound card for it.
87 example)
89 sound {
90 compatible = "simple-scu-audio-card";
91 ...
92 /*
93 * SRC Asynchronous mode setting
94 * Playback:
95 * All input data will be converted to 48kHz
96 * Capture:
97 * Inputed 48kHz data will be converted to
98 * system specified Hz
99 */
100 simple-audio-card,convert-rate = <48000>;
101 ...
102 simple-audio-card,cpu {
103 sound-dai = <&rcar_sound>;
104 };
105 simple-audio-card,codec {
106 ...
107 };
108 };
110 ------------------
111 ** Synchronous mode
112 ------------------
114 > amixer set "SRC Out Rate" on
115 > aplay xxxx.wav
116 > amixer set "SRC Out Rate" 48000
117 > amixer set "SRC Out Rate" 44100
119 =============================================
120 * CTU (Channel Transfer Unit)
121 =============================================
123 [xx]ch [yy]ch
124 ------> [CTU] -------->
126 CTU can convert [xx]ch to [yy]ch, or exchange outputed channel.
127 CTU conversion needs matrix settings.
128 For more detail information, see below
130 Renesas R-Car datasheet
131 - Sampling Rate Converter Unit (SCU)
132 - SCU Operation
133 - CMD Block
134 - Functional Blocks in CMD
136 Renesas R-Car datasheet
137 - Sampling Rate Converter Unit (SCU)
138 - Register Description
139 - CTUn Scale Value exx Register (CTUn_SVxxR)
141 ${LINUX}/sound/soc/sh/rcar/ctu.c
142 - comment of header
144 You need to use "simple-scu-audio-card" sound card for it.
145 example)
147 sound {
148 compatible = "simple-scu-audio-card";
149 ...
150 /*
151 * CTU setting
152 * All input data will be converted to 2ch
153 * as output data
154 */
155 simple-audio-card,convert-channels = <2>;
156 ...
157 simple-audio-card,cpu {
158 sound-dai = <&rcar_sound>;
159 };
160 simple-audio-card,codec {
161 ...
162 };
163 };
165 Ex) Exchange output channel
166 Input -> Output
167 1ch -> 0ch
168 0ch -> 1ch
170 example of using matrix
171 output 0ch = (input 0ch x 0) + (input 1ch x 1)
172 output 1ch = (input 0ch x 1) + (input 1ch x 0)
174 amixer set "CTU Reset" on
175 amixer set "CTU Pass" 9,10
176 amixer set "CTU SV0" 0,4194304
177 amixer set "CTU SV1" 4194304,0
179 example of changing connection
180 amixer set "CTU Reset" on
181 amixer set "CTU Pass" 2,1
183 =============================================
184 * MIX (Mixer)
185 =============================================
187 MIX merges 2 sounds path. You can see 2 sound interface on system,
188 and these sounds will be merged by MIX.
190 aplay -D plughw:0,0 xxxx.wav &
191 aplay -D plughw:0,1 yyyy.wav
193 You need to use "simple-scu-audio-card" sound card for it.
194 Ex)
195 [MEM] -> [SRC1] -> [CTU02] -+-> [MIX0] -> [DVC0] -> [SSI0]
196 |
197 [MEM] -> [SRC2] -> [CTU03] -+
199 sound {
200 #address-cells = <1>;
201 #size-cells = <0>;
203 compatible = "simple-scu-audio-card";
204 ...
205 simple-audio-card,cpu@0 {
206 reg = <0>;
207 sound-dai = <&rcar_sound 0>;
208 };
209 simple-audio-card,cpu@1 {
210 reg = <1>;
211 sound-dai = <&rcar_sound 1>;
212 };
213 simple-audio-card,codec {
214 ...
215 };
216 };
218 &rcar_sound {
219 ...
220 rcar_sound,dai {
221 dai0 {
222 playback = <&src1 &ctu02 &mix0 &dvc0 &ssi0>;
223 };
224 dai1 {
225 playback = <&src2 &ctu03 &mix0 &dvc0 &ssi0>;
226 };
227 };
228 };
230 =============================================
231 * DVC (Digital Volume and Mute Function)
232 =============================================
234 DVC controls Playback/Capture volume.
236 Playback Volume
237 amixer set "DVC Out" 100%
239 Capture Volume
240 amixer set "DVC In" 100%
242 Playback Mute
243 amixer set "DVC Out Mute" on
245 Capture Mute
246 amixer set "DVC In Mute" on
248 Volume Ramp
249 amixer set "DVC Out Ramp Up Rate" "0.125 dB/64 steps"
250 amixer set "DVC Out Ramp Down Rate" "0.125 dB/512 steps"
251 amixer set "DVC Out Ramp" on
252 aplay xxx.wav &
253 amixer set "DVC Out" 80% // Volume Down
254 amixer set "DVC Out" 100% // Volume Up
256 =============================================
257 * SSIU (Serial Sound Interface Unit)
258 =============================================
260 There is no DT settings for SSIU, because SSIU will be automatically
261 selected via SSI.
262 SSIU can avoid some under/over run error, because it has some buffer.
263 But you can't use it if SSI was PIO mode.
264 In DMA mode, you can select not to use SSIU by using "no-busif" on DT.
266 &ssi0 {
267 no-busif;
268 };
270 =============================================
271 * SSI (Serial Sound Interface)
272 =============================================
274 ** PIO mode
276 You can use PIO mode which is for connection check by using.
277 Note: The system will drop non-SSI modules in PIO mode
278 even though if DT is selecting other modules.
280 &ssi0 {
281 pio-transfer
282 };
284 ** DMA mode without SSIU
286 You can use DMA without SSIU.
287 Note: under/over run, or noise are likely to occur
289 &ssi0 {
290 no-busif;
291 };
293 ** PIN sharing
295 Each SSI can share WS pin. It is based on platform.
296 This is example if SSI1 want to share WS pin with SSI0
298 &ssi1 {
299 shared-pin;
300 };
302 ** Multi-SSI
304 You can use Multi-SSI.
305 This is example of SSI0/SSI1/SSI2 (= for 6ch)
307 &rcar_sound {
308 ...
309 rcar_sound,dai {
310 dai0 {
311 playback = <&ssi0 &ssi1 &ssi2 &src0 &dvc0>;
312 };
313 };
314 };
316 ** TDM-SSI
318 You can use TDM with SSI.
319 This is example of TDM 6ch.
320 Driver can automatically switches TDM <-> stereo mode in this case.
322 rsnd_tdm: sound {
323 compatible = "simple-audio-card";
324 ...
325 simple-audio-card,cpu {
326 /* system can use TDM 6ch */
327 dai-tdm-slot-num = <6>;
328 sound-dai = <&rcar_sound>;
329 };
330 simple-audio-card,codec {
331 ...
332 };
333 };
336 =============================================
337 Required properties:
338 =============================================
340 - compatible : "renesas,rcar_sound-<soctype>", fallbacks
341 "renesas,rcar_sound-gen1" if generation1, and
342 "renesas,rcar_sound-gen2" if generation2 (or RZ/G1)
343 "renesas,rcar_sound-gen3" if generation3 (or RZ/G2)
344 Examples with soctypes are:
345 - "renesas,rcar_sound-r8a7743" (RZ/G1M)
346 - "renesas,rcar_sound-r8a7744" (RZ/G1N)
347 - "renesas,rcar_sound-r8a7745" (RZ/G1E)
348 - "renesas,rcar_sound-r8a774a1" (RZ/G2M)
349 - "renesas,rcar_sound-r8a7778" (R-Car M1A)
350 - "renesas,rcar_sound-r8a7779" (R-Car H1)
351 - "renesas,rcar_sound-r8a7790" (R-Car H2)
352 - "renesas,rcar_sound-r8a7791" (R-Car M2-W)
353 - "renesas,rcar_sound-r8a7793" (R-Car M2-N)
354 - "renesas,rcar_sound-r8a7794" (R-Car E2)
355 - "renesas,rcar_sound-r8a7795" (R-Car H3)
356 - "renesas,rcar_sound-r8a7796" (R-Car M3-W)
357 - "renesas,rcar_sound-r8a77965" (R-Car M3-N)
358 - "renesas,rcar_sound-r8a77990" (R-Car E3)
359 - reg : Should contain the register physical address.
360 required register is
361 SRU/ADG/SSI if generation1
362 SRU/ADG/SSIU/SSI if generation2
363 - rcar_sound,ssi : Should contain SSI feature.
364 The number of SSI subnode should be same as HW.
365 see below for detail.
366 - rcar_sound,src : Should contain SRC feature.
367 The number of SRC subnode should be same as HW.
368 see below for detail.
369 - rcar_sound,ctu : Should contain CTU feature.
370 The number of CTU subnode should be same as HW.
371 see below for detail.
372 - rcar_sound,mix : Should contain MIX feature.
373 The number of MIX subnode should be same as HW.
374 see below for detail.
375 - rcar_sound,dvc : Should contain DVC feature.
376 The number of DVC subnode should be same as HW.
377 see below for detail.
378 - rcar_sound,dai : DAI contents.
379 The number of DAI subnode should be same as HW.
380 see below for detail.
381 - #sound-dai-cells : it must be 0 if your system is using single DAI
382 it must be 1 if your system is using multi DAI
383 - clocks : References to SSI/SRC/MIX/CTU/DVC/AUDIO_CLK clocks.
384 - clock-names : List of necessary clock names.
385 "ssi-all", "ssi.X", "src.X", "mix.X", "ctu.X",
386 "dvc.X", "clk_a", "clk_b", "clk_c", "clk_i"
388 Optional properties:
389 - #clock-cells : it must be 0 if your system has audio_clkout
390 it must be 1 if your system has audio_clkout0/1/2/3
391 - clock-frequency : for all audio_clkout0/1/2/3
392 - clkout-lr-asynchronous : boolean property. it indicates that audio_clkoutn
393 is asynchronizes with lr-clock.
394 - resets : References to SSI resets.
395 - reset-names : List of valid reset names.
396 "ssi-all", "ssi.X"
398 SSI subnode properties:
399 - interrupts : Should contain SSI interrupt for PIO transfer
400 - shared-pin : if shared clock pin
401 - pio-transfer : use PIO transfer mode
402 - no-busif : BUSIF is not ussed when [mem -> SSI] via DMA case
403 - dma : Should contain Audio DMAC entry
404 - dma-names : SSI case "rx" (=playback), "tx" (=capture)
405 SSIU case "rxu" (=playback), "txu" (=capture)
407 SRC subnode properties:
408 - dma : Should contain Audio DMAC entry
409 - dma-names : "rx" (=playback), "tx" (=capture)
411 DVC subnode properties:
412 - dma : Should contain Audio DMAC entry
413 - dma-names : "tx" (=playback/capture)
415 DAI subnode properties:
416 - playback : list of playback modules
417 - capture : list of capture modules
420 =============================================
421 Example:
422 =============================================
424 rcar_sound: sound@ec500000 {
425 #sound-dai-cells = <1>;
426 compatible = "renesas,rcar_sound-r8a7791", "renesas,rcar_sound-gen2";
427 reg = <0 0xec500000 0 0x1000>, /* SCU */
428 <0 0xec5a0000 0 0x100>, /* ADG */
429 <0 0xec540000 0 0x1000>, /* SSIU */
430 <0 0xec541000 0 0x1280>, /* SSI */
431 <0 0xec740000 0 0x200>; /* Audio DMAC peri peri*/
432 reg-names = "scu", "adg", "ssiu", "ssi", "audmapp";
434 clocks = <&mstp10_clks R8A7790_CLK_SSI_ALL>,
435 <&mstp10_clks R8A7790_CLK_SSI9>, <&mstp10_clks R8A7790_CLK_SSI8>,
436 <&mstp10_clks R8A7790_CLK_SSI7>, <&mstp10_clks R8A7790_CLK_SSI6>,
437 <&mstp10_clks R8A7790_CLK_SSI5>, <&mstp10_clks R8A7790_CLK_SSI4>,
438 <&mstp10_clks R8A7790_CLK_SSI3>, <&mstp10_clks R8A7790_CLK_SSI2>,
439 <&mstp10_clks R8A7790_CLK_SSI1>, <&mstp10_clks R8A7790_CLK_SSI0>,
440 <&mstp10_clks R8A7790_CLK_SCU_SRC9>, <&mstp10_clks R8A7790_CLK_SCU_SRC8>,
441 <&mstp10_clks R8A7790_CLK_SCU_SRC7>, <&mstp10_clks R8A7790_CLK_SCU_SRC6>,
442 <&mstp10_clks R8A7790_CLK_SCU_SRC5>, <&mstp10_clks R8A7790_CLK_SCU_SRC4>,
443 <&mstp10_clks R8A7790_CLK_SCU_SRC3>, <&mstp10_clks R8A7790_CLK_SCU_SRC2>,
444 <&mstp10_clks R8A7790_CLK_SCU_SRC1>, <&mstp10_clks R8A7790_CLK_SCU_SRC0>,
445 <&mstp10_clks R8A7790_CLK_SCU_DVC0>, <&mstp10_clks R8A7790_CLK_SCU_DVC1>,
446 <&audio_clk_a>, <&audio_clk_b>, <&audio_clk_c>, <&m2_clk>;
447 clock-names = "ssi-all",
448 "ssi.9", "ssi.8", "ssi.7", "ssi.6", "ssi.5",
449 "ssi.4", "ssi.3", "ssi.2", "ssi.1", "ssi.0",
450 "src.9", "src.8", "src.7", "src.6", "src.5",
451 "src.4", "src.3", "src.2", "src.1", "src.0",
452 "dvc.0", "dvc.1",
453 "clk_a", "clk_b", "clk_c", "clk_i";
455 rcar_sound,dvc {
456 dvc0: dvc-0 {
457 dmas = <&audma0 0xbc>;
458 dma-names = "tx";
459 };
460 dvc1: dvc-1 {
461 dmas = <&audma0 0xbe>;
462 dma-names = "tx";
463 };
464 };
466 rcar_sound,mix {
467 mix0: mix-0 { };
468 mix1: mix-1 { };
469 };
471 rcar_sound,ctu {
472 ctu00: ctu-0 { };
473 ctu01: ctu-1 { };
474 ctu02: ctu-2 { };
475 ctu03: ctu-3 { };
476 ctu10: ctu-4 { };
477 ctu11: ctu-5 { };
478 ctu12: ctu-6 { };
479 ctu13: ctu-7 { };
480 };
482 rcar_sound,src {
483 src0: src-0 {
484 interrupts = <0 352 IRQ_TYPE_LEVEL_HIGH>;
485 dmas = <&audma0 0x85>, <&audma1 0x9a>;
486 dma-names = "rx", "tx";
487 };
488 src1: src-1 {
489 interrupts = <0 353 IRQ_TYPE_LEVEL_HIGH>;
490 dmas = <&audma0 0x87>, <&audma1 0x9c>;
491 dma-names = "rx", "tx";
492 };
493 src2: src-2 {
494 interrupts = <0 354 IRQ_TYPE_LEVEL_HIGH>;
495 dmas = <&audma0 0x89>, <&audma1 0x9e>;
496 dma-names = "rx", "tx";
497 };
498 src3: src-3 {
499 interrupts = <0 355 IRQ_TYPE_LEVEL_HIGH>;
500 dmas = <&audma0 0x8b>, <&audma1 0xa0>;
501 dma-names = "rx", "tx";
502 };
503 src4: src-4 {
504 interrupts = <0 356 IRQ_TYPE_LEVEL_HIGH>;
505 dmas = <&audma0 0x8d>, <&audma1 0xb0>;
506 dma-names = "rx", "tx";
507 };
508 src5: src-5 {
509 interrupts = <0 357 IRQ_TYPE_LEVEL_HIGH>;
510 dmas = <&audma0 0x8f>, <&audma1 0xb2>;
511 dma-names = "rx", "tx";
512 };
513 src6: src-6 {
514 interrupts = <0 358 IRQ_TYPE_LEVEL_HIGH>;
515 dmas = <&audma0 0x91>, <&audma1 0xb4>;
516 dma-names = "rx", "tx";
517 };
518 src7: src-7 {
519 interrupts = <0 359 IRQ_TYPE_LEVEL_HIGH>;
520 dmas = <&audma0 0x93>, <&audma1 0xb6>;
521 dma-names = "rx", "tx";
522 };
523 src8: src-8 {
524 interrupts = <0 360 IRQ_TYPE_LEVEL_HIGH>;
525 dmas = <&audma0 0x95>, <&audma1 0xb8>;
526 dma-names = "rx", "tx";
527 };
528 src9: src-9 {
529 interrupts = <0 361 IRQ_TYPE_LEVEL_HIGH>;
530 dmas = <&audma0 0x97>, <&audma1 0xba>;
531 dma-names = "rx", "tx";
532 };
533 };
535 rcar_sound,ssi {
536 ssi0: ssi-0 {
537 interrupts = <0 370 IRQ_TYPE_LEVEL_HIGH>;
538 dmas = <&audma0 0x01>, <&audma1 0x02>, <&audma0 0x15>, <&audma1 0x16>;
539 dma-names = "rx", "tx", "rxu", "txu";
540 };
541 ssi1: ssi-1 {
542 interrupts = <0 371 IRQ_TYPE_LEVEL_HIGH>;
543 dmas = <&audma0 0x03>, <&audma1 0x04>, <&audma0 0x49>, <&audma1 0x4a>;
544 dma-names = "rx", "tx", "rxu", "txu";
545 };
546 ssi2: ssi-2 {
547 interrupts = <0 372 IRQ_TYPE_LEVEL_HIGH>;
548 dmas = <&audma0 0x05>, <&audma1 0x06>, <&audma0 0x63>, <&audma1 0x64>;
549 dma-names = "rx", "tx", "rxu", "txu";
550 };
551 ssi3: ssi-3 {
552 interrupts = <0 373 IRQ_TYPE_LEVEL_HIGH>;
553 dmas = <&audma0 0x07>, <&audma1 0x08>, <&audma0 0x6f>, <&audma1 0x70>;
554 dma-names = "rx", "tx", "rxu", "txu";
555 };
556 ssi4: ssi-4 {
557 interrupts = <0 374 IRQ_TYPE_LEVEL_HIGH>;
558 dmas = <&audma0 0x09>, <&audma1 0x0a>, <&audma0 0x71>, <&audma1 0x72>;
559 dma-names = "rx", "tx", "rxu", "txu";
560 };
561 ssi5: ssi-5 {
562 interrupts = <0 375 IRQ_TYPE_LEVEL_HIGH>;
563 dmas = <&audma0 0x0b>, <&audma1 0x0c>, <&audma0 0x73>, <&audma1 0x74>;
564 dma-names = "rx", "tx", "rxu", "txu";
565 };
566 ssi6: ssi-6 {
567 interrupts = <0 376 IRQ_TYPE_LEVEL_HIGH>;
568 dmas = <&audma0 0x0d>, <&audma1 0x0e>, <&audma0 0x75>, <&audma1 0x76>;
569 dma-names = "rx", "tx", "rxu", "txu";
570 };
571 ssi7: ssi-7 {
572 interrupts = <0 377 IRQ_TYPE_LEVEL_HIGH>;
573 dmas = <&audma0 0x0f>, <&audma1 0x10>, <&audma0 0x79>, <&audma1 0x7a>;
574 dma-names = "rx", "tx", "rxu", "txu";
575 };
576 ssi8: ssi-8 {
577 interrupts = <0 378 IRQ_TYPE_LEVEL_HIGH>;
578 dmas = <&audma0 0x11>, <&audma1 0x12>, <&audma0 0x7b>, <&audma1 0x7c>;
579 dma-names = "rx", "tx", "rxu", "txu";
580 };
581 ssi9: ssi-9 {
582 interrupts = <0 379 IRQ_TYPE_LEVEL_HIGH>;
583 dmas = <&audma0 0x13>, <&audma1 0x14>, <&audma0 0x7d>, <&audma1 0x7e>;
584 dma-names = "rx", "tx", "rxu", "txu";
585 };
586 };
588 rcar_sound,dai {
589 dai0 {
590 playback = <&ssi5 &src5>;
591 capture = <&ssi6>;
592 };
593 dai1 {
594 playback = <&ssi3>;
595 };
596 dai2 {
597 capture = <&ssi4>;
598 };
599 dai3 {
600 playback = <&ssi7>;
601 };
602 dai4 {
603 capture = <&ssi8>;
604 };
605 };
606 };
608 =============================================
609 Example: simple sound card
610 =============================================
612 rsnd_ak4643: sound {
613 compatible = "simple-audio-card";
615 simple-audio-card,format = "left_j";
616 simple-audio-card,bitclock-master = <&sndcodec>;
617 simple-audio-card,frame-master = <&sndcodec>;
619 sndcpu: simple-audio-card,cpu {
620 sound-dai = <&rcar_sound>;
621 };
623 sndcodec: simple-audio-card,codec {
624 sound-dai = <&ak4643>;
625 clocks = <&audio_clock>;
626 };
627 };
629 &rcar_sound {
630 pinctrl-0 = <&sound_pins &sound_clk_pins>;
631 pinctrl-names = "default";
633 /* Single DAI */
634 #sound-dai-cells = <0>;
637 rcar_sound,dai {
638 dai0 {
639 playback = <&ssi0 &src2 &dvc0>;
640 capture = <&ssi1 &src3 &dvc1>;
641 };
642 };
643 };
645 &ssi1 {
646 shared-pin;
647 };
649 =============================================
650 Example: simple sound card for TDM
651 =============================================
653 rsnd_tdm: sound {
654 compatible = "simple-audio-card";
656 simple-audio-card,format = "left_j";
657 simple-audio-card,bitclock-master = <&sndcodec>;
658 simple-audio-card,frame-master = <&sndcodec>;
660 sndcpu: simple-audio-card,cpu {
661 sound-dai = <&rcar_sound>;
662 dai-tdm-slot-num = <6>;
663 };
665 sndcodec: simple-audio-card,codec {
666 sound-dai = <&xxx>;
667 };
668 };
670 =============================================
671 Example: simple sound card for Multi channel
672 =============================================
674 &rcar_sound {
675 pinctrl-0 = <&sound_pins &sound_clk_pins>;
676 pinctrl-names = "default";
678 /* Single DAI */
679 #sound-dai-cells = <0>;
682 rcar_sound,dai {
683 dai0 {
684 playback = <&ssi0 &ssi1 &ssi2 &src0 &dvc0>;
685 };
686 };
687 };