KVM: nVMX: Fix returned value of MSR_IA32_VMX_VMCS_ENUM
[linux/fpc-iii.git] / drivers / mtd / nand / atmel_nand.c
blob4ce181a35bcd3eedf39c8fd3a5c617306278ef58
1 /*
2 * Copyright © 2003 Rick Bronson
4 * Derived from drivers/mtd/nand/autcpu12.c
5 * Copyright © 2001 Thomas Gleixner (gleixner@autronix.de)
7 * Derived from drivers/mtd/spia.c
8 * Copyright © 2000 Steven J. Hill (sjhill@cotw.com)
11 * Add Hardware ECC support for AT91SAM9260 / AT91SAM9263
12 * Richard Genoud (richard.genoud@gmail.com), Adeneo Copyright © 2007
14 * Derived from Das U-Boot source code
15 * (u-boot-1.1.5/board/atmel/at91sam9263ek/nand.c)
16 * © Copyright 2006 ATMEL Rousset, Lacressonniere Nicolas
18 * Add Programmable Multibit ECC support for various AT91 SoC
19 * © Copyright 2012 ATMEL, Hong Xu
21 * Add Nand Flash Controller support for SAMA5 SoC
22 * © Copyright 2013 ATMEL, Josh Wu (josh.wu@atmel.com)
24 * This program is free software; you can redistribute it and/or modify
25 * it under the terms of the GNU General Public License version 2 as
26 * published by the Free Software Foundation.
30 #include <linux/dma-mapping.h>
31 #include <linux/slab.h>
32 #include <linux/module.h>
33 #include <linux/moduleparam.h>
34 #include <linux/platform_device.h>
35 #include <linux/of.h>
36 #include <linux/of_device.h>
37 #include <linux/of_gpio.h>
38 #include <linux/of_mtd.h>
39 #include <linux/mtd/mtd.h>
40 #include <linux/mtd/nand.h>
41 #include <linux/mtd/partitions.h>
43 #include <linux/delay.h>
44 #include <linux/dmaengine.h>
45 #include <linux/gpio.h>
46 #include <linux/interrupt.h>
47 #include <linux/io.h>
48 #include <linux/platform_data/atmel.h>
50 static int use_dma = 1;
51 module_param(use_dma, int, 0);
53 static int on_flash_bbt = 0;
54 module_param(on_flash_bbt, int, 0);
56 /* Register access macros */
57 #define ecc_readl(add, reg) \
58 __raw_readl(add + ATMEL_ECC_##reg)
59 #define ecc_writel(add, reg, value) \
60 __raw_writel((value), add + ATMEL_ECC_##reg)
62 #include "atmel_nand_ecc.h" /* Hardware ECC registers */
63 #include "atmel_nand_nfc.h" /* Nand Flash Controller definition */
65 /* oob layout for large page size
66 * bad block info is on bytes 0 and 1
67 * the bytes have to be consecutives to avoid
68 * several NAND_CMD_RNDOUT during read
70 static struct nand_ecclayout atmel_oobinfo_large = {
71 .eccbytes = 4,
72 .eccpos = {60, 61, 62, 63},
73 .oobfree = {
74 {2, 58}
78 /* oob layout for small page size
79 * bad block info is on bytes 4 and 5
80 * the bytes have to be consecutives to avoid
81 * several NAND_CMD_RNDOUT during read
83 static struct nand_ecclayout atmel_oobinfo_small = {
84 .eccbytes = 4,
85 .eccpos = {0, 1, 2, 3},
86 .oobfree = {
87 {6, 10}
91 struct atmel_nfc {
92 void __iomem *base_cmd_regs;
93 void __iomem *hsmc_regs;
94 void __iomem *sram_bank0;
95 dma_addr_t sram_bank0_phys;
96 bool use_nfc_sram;
97 bool write_by_sram;
99 bool is_initialized;
100 struct completion comp_nfc;
102 /* Point to the sram bank which include readed data via NFC */
103 void __iomem *data_in_sram;
104 bool will_write_sram;
106 static struct atmel_nfc nand_nfc;
108 struct atmel_nand_host {
109 struct nand_chip nand_chip;
110 struct mtd_info mtd;
111 void __iomem *io_base;
112 dma_addr_t io_phys;
113 struct atmel_nand_data board;
114 struct device *dev;
115 void __iomem *ecc;
117 struct completion comp;
118 struct dma_chan *dma_chan;
120 struct atmel_nfc *nfc;
122 bool has_pmecc;
123 u8 pmecc_corr_cap;
124 u16 pmecc_sector_size;
125 u32 pmecc_lookup_table_offset;
126 u32 pmecc_lookup_table_offset_512;
127 u32 pmecc_lookup_table_offset_1024;
129 int pmecc_bytes_per_sector;
130 int pmecc_sector_number;
131 int pmecc_degree; /* Degree of remainders */
132 int pmecc_cw_len; /* Length of codeword */
134 void __iomem *pmerrloc_base;
135 void __iomem *pmecc_rom_base;
137 /* lookup table for alpha_to and index_of */
138 void __iomem *pmecc_alpha_to;
139 void __iomem *pmecc_index_of;
141 /* data for pmecc computation */
142 int16_t *pmecc_partial_syn;
143 int16_t *pmecc_si;
144 int16_t *pmecc_smu; /* Sigma table */
145 int16_t *pmecc_lmu; /* polynomal order */
146 int *pmecc_mu;
147 int *pmecc_dmu;
148 int *pmecc_delta;
151 static struct nand_ecclayout atmel_pmecc_oobinfo;
154 * Enable NAND.
156 static void atmel_nand_enable(struct atmel_nand_host *host)
158 if (gpio_is_valid(host->board.enable_pin))
159 gpio_set_value(host->board.enable_pin, 0);
163 * Disable NAND.
165 static void atmel_nand_disable(struct atmel_nand_host *host)
167 if (gpio_is_valid(host->board.enable_pin))
168 gpio_set_value(host->board.enable_pin, 1);
172 * Hardware specific access to control-lines
174 static void atmel_nand_cmd_ctrl(struct mtd_info *mtd, int cmd, unsigned int ctrl)
176 struct nand_chip *nand_chip = mtd->priv;
177 struct atmel_nand_host *host = nand_chip->priv;
179 if (ctrl & NAND_CTRL_CHANGE) {
180 if (ctrl & NAND_NCE)
181 atmel_nand_enable(host);
182 else
183 atmel_nand_disable(host);
185 if (cmd == NAND_CMD_NONE)
186 return;
188 if (ctrl & NAND_CLE)
189 writeb(cmd, host->io_base + (1 << host->board.cle));
190 else
191 writeb(cmd, host->io_base + (1 << host->board.ale));
195 * Read the Device Ready pin.
197 static int atmel_nand_device_ready(struct mtd_info *mtd)
199 struct nand_chip *nand_chip = mtd->priv;
200 struct atmel_nand_host *host = nand_chip->priv;
202 return gpio_get_value(host->board.rdy_pin) ^
203 !!host->board.rdy_pin_active_low;
206 /* Set up for hardware ready pin and enable pin. */
207 static int atmel_nand_set_enable_ready_pins(struct mtd_info *mtd)
209 struct nand_chip *chip = mtd->priv;
210 struct atmel_nand_host *host = chip->priv;
211 int res = 0;
213 if (gpio_is_valid(host->board.rdy_pin)) {
214 res = devm_gpio_request(host->dev,
215 host->board.rdy_pin, "nand_rdy");
216 if (res < 0) {
217 dev_err(host->dev,
218 "can't request rdy gpio %d\n",
219 host->board.rdy_pin);
220 return res;
223 res = gpio_direction_input(host->board.rdy_pin);
224 if (res < 0) {
225 dev_err(host->dev,
226 "can't request input direction rdy gpio %d\n",
227 host->board.rdy_pin);
228 return res;
231 chip->dev_ready = atmel_nand_device_ready;
234 if (gpio_is_valid(host->board.enable_pin)) {
235 res = devm_gpio_request(host->dev,
236 host->board.enable_pin, "nand_enable");
237 if (res < 0) {
238 dev_err(host->dev,
239 "can't request enable gpio %d\n",
240 host->board.enable_pin);
241 return res;
244 res = gpio_direction_output(host->board.enable_pin, 1);
245 if (res < 0) {
246 dev_err(host->dev,
247 "can't request output direction enable gpio %d\n",
248 host->board.enable_pin);
249 return res;
253 return res;
256 static void memcpy32_fromio(void *trg, const void __iomem *src, size_t size)
258 int i;
259 u32 *t = trg;
260 const __iomem u32 *s = src;
262 for (i = 0; i < (size >> 2); i++)
263 *t++ = readl_relaxed(s++);
266 static void memcpy32_toio(void __iomem *trg, const void *src, int size)
268 int i;
269 u32 __iomem *t = trg;
270 const u32 *s = src;
272 for (i = 0; i < (size >> 2); i++)
273 writel_relaxed(*s++, t++);
277 * Minimal-overhead PIO for data access.
279 static void atmel_read_buf8(struct mtd_info *mtd, u8 *buf, int len)
281 struct nand_chip *nand_chip = mtd->priv;
282 struct atmel_nand_host *host = nand_chip->priv;
284 if (host->nfc && host->nfc->use_nfc_sram && host->nfc->data_in_sram) {
285 memcpy32_fromio(buf, host->nfc->data_in_sram, len);
286 host->nfc->data_in_sram += len;
287 } else {
288 __raw_readsb(nand_chip->IO_ADDR_R, buf, len);
292 static void atmel_read_buf16(struct mtd_info *mtd, u8 *buf, int len)
294 struct nand_chip *nand_chip = mtd->priv;
295 struct atmel_nand_host *host = nand_chip->priv;
297 if (host->nfc && host->nfc->use_nfc_sram && host->nfc->data_in_sram) {
298 memcpy32_fromio(buf, host->nfc->data_in_sram, len);
299 host->nfc->data_in_sram += len;
300 } else {
301 __raw_readsw(nand_chip->IO_ADDR_R, buf, len / 2);
305 static void atmel_write_buf8(struct mtd_info *mtd, const u8 *buf, int len)
307 struct nand_chip *nand_chip = mtd->priv;
309 __raw_writesb(nand_chip->IO_ADDR_W, buf, len);
312 static void atmel_write_buf16(struct mtd_info *mtd, const u8 *buf, int len)
314 struct nand_chip *nand_chip = mtd->priv;
316 __raw_writesw(nand_chip->IO_ADDR_W, buf, len / 2);
319 static void dma_complete_func(void *completion)
321 complete(completion);
324 static int nfc_set_sram_bank(struct atmel_nand_host *host, unsigned int bank)
326 /* NFC only has two banks. Must be 0 or 1 */
327 if (bank > 1)
328 return -EINVAL;
330 if (bank) {
331 /* Only for a 2k-page or lower flash, NFC can handle 2 banks */
332 if (host->mtd.writesize > 2048)
333 return -EINVAL;
334 nfc_writel(host->nfc->hsmc_regs, BANK, ATMEL_HSMC_NFC_BANK1);
335 } else {
336 nfc_writel(host->nfc->hsmc_regs, BANK, ATMEL_HSMC_NFC_BANK0);
339 return 0;
342 static uint nfc_get_sram_off(struct atmel_nand_host *host)
344 if (nfc_readl(host->nfc->hsmc_regs, BANK) & ATMEL_HSMC_NFC_BANK1)
345 return NFC_SRAM_BANK1_OFFSET;
346 else
347 return 0;
350 static dma_addr_t nfc_sram_phys(struct atmel_nand_host *host)
352 if (nfc_readl(host->nfc->hsmc_regs, BANK) & ATMEL_HSMC_NFC_BANK1)
353 return host->nfc->sram_bank0_phys + NFC_SRAM_BANK1_OFFSET;
354 else
355 return host->nfc->sram_bank0_phys;
358 static int atmel_nand_dma_op(struct mtd_info *mtd, void *buf, int len,
359 int is_read)
361 struct dma_device *dma_dev;
362 enum dma_ctrl_flags flags;
363 dma_addr_t dma_src_addr, dma_dst_addr, phys_addr;
364 struct dma_async_tx_descriptor *tx = NULL;
365 dma_cookie_t cookie;
366 struct nand_chip *chip = mtd->priv;
367 struct atmel_nand_host *host = chip->priv;
368 void *p = buf;
369 int err = -EIO;
370 enum dma_data_direction dir = is_read ? DMA_FROM_DEVICE : DMA_TO_DEVICE;
371 struct atmel_nfc *nfc = host->nfc;
373 if (buf >= high_memory)
374 goto err_buf;
376 dma_dev = host->dma_chan->device;
378 flags = DMA_CTRL_ACK | DMA_PREP_INTERRUPT;
380 phys_addr = dma_map_single(dma_dev->dev, p, len, dir);
381 if (dma_mapping_error(dma_dev->dev, phys_addr)) {
382 dev_err(host->dev, "Failed to dma_map_single\n");
383 goto err_buf;
386 if (is_read) {
387 if (nfc && nfc->data_in_sram)
388 dma_src_addr = nfc_sram_phys(host) + (nfc->data_in_sram
389 - (nfc->sram_bank0 + nfc_get_sram_off(host)));
390 else
391 dma_src_addr = host->io_phys;
393 dma_dst_addr = phys_addr;
394 } else {
395 dma_src_addr = phys_addr;
397 if (nfc && nfc->write_by_sram)
398 dma_dst_addr = nfc_sram_phys(host);
399 else
400 dma_dst_addr = host->io_phys;
403 tx = dma_dev->device_prep_dma_memcpy(host->dma_chan, dma_dst_addr,
404 dma_src_addr, len, flags);
405 if (!tx) {
406 dev_err(host->dev, "Failed to prepare DMA memcpy\n");
407 goto err_dma;
410 init_completion(&host->comp);
411 tx->callback = dma_complete_func;
412 tx->callback_param = &host->comp;
414 cookie = tx->tx_submit(tx);
415 if (dma_submit_error(cookie)) {
416 dev_err(host->dev, "Failed to do DMA tx_submit\n");
417 goto err_dma;
420 dma_async_issue_pending(host->dma_chan);
421 wait_for_completion(&host->comp);
423 if (is_read && nfc && nfc->data_in_sram)
424 /* After read data from SRAM, need to increase the position */
425 nfc->data_in_sram += len;
427 err = 0;
429 err_dma:
430 dma_unmap_single(dma_dev->dev, phys_addr, len, dir);
431 err_buf:
432 if (err != 0)
433 dev_dbg(host->dev, "Fall back to CPU I/O\n");
434 return err;
437 static void atmel_read_buf(struct mtd_info *mtd, u8 *buf, int len)
439 struct nand_chip *chip = mtd->priv;
440 struct atmel_nand_host *host = chip->priv;
442 if (use_dma && len > mtd->oobsize)
443 /* only use DMA for bigger than oob size: better performances */
444 if (atmel_nand_dma_op(mtd, buf, len, 1) == 0)
445 return;
447 if (host->board.bus_width_16)
448 atmel_read_buf16(mtd, buf, len);
449 else
450 atmel_read_buf8(mtd, buf, len);
453 static void atmel_write_buf(struct mtd_info *mtd, const u8 *buf, int len)
455 struct nand_chip *chip = mtd->priv;
456 struct atmel_nand_host *host = chip->priv;
458 if (use_dma && len > mtd->oobsize)
459 /* only use DMA for bigger than oob size: better performances */
460 if (atmel_nand_dma_op(mtd, (void *)buf, len, 0) == 0)
461 return;
463 if (host->board.bus_width_16)
464 atmel_write_buf16(mtd, buf, len);
465 else
466 atmel_write_buf8(mtd, buf, len);
470 * Return number of ecc bytes per sector according to sector size and
471 * correction capability
473 * Following table shows what at91 PMECC supported:
474 * Correction Capability Sector_512_bytes Sector_1024_bytes
475 * ===================== ================ =================
476 * 2-bits 4-bytes 4-bytes
477 * 4-bits 7-bytes 7-bytes
478 * 8-bits 13-bytes 14-bytes
479 * 12-bits 20-bytes 21-bytes
480 * 24-bits 39-bytes 42-bytes
482 static int pmecc_get_ecc_bytes(int cap, int sector_size)
484 int m = 12 + sector_size / 512;
485 return (m * cap + 7) / 8;
488 static void pmecc_config_ecc_layout(struct nand_ecclayout *layout,
489 int oobsize, int ecc_len)
491 int i;
493 layout->eccbytes = ecc_len;
495 /* ECC will occupy the last ecc_len bytes continuously */
496 for (i = 0; i < ecc_len; i++)
497 layout->eccpos[i] = oobsize - ecc_len + i;
499 layout->oobfree[0].offset = 2;
500 layout->oobfree[0].length =
501 oobsize - ecc_len - layout->oobfree[0].offset;
504 static void __iomem *pmecc_get_alpha_to(struct atmel_nand_host *host)
506 int table_size;
508 table_size = host->pmecc_sector_size == 512 ?
509 PMECC_LOOKUP_TABLE_SIZE_512 : PMECC_LOOKUP_TABLE_SIZE_1024;
511 return host->pmecc_rom_base + host->pmecc_lookup_table_offset +
512 table_size * sizeof(int16_t);
515 static int pmecc_data_alloc(struct atmel_nand_host *host)
517 const int cap = host->pmecc_corr_cap;
518 int size;
520 size = (2 * cap + 1) * sizeof(int16_t);
521 host->pmecc_partial_syn = devm_kzalloc(host->dev, size, GFP_KERNEL);
522 host->pmecc_si = devm_kzalloc(host->dev, size, GFP_KERNEL);
523 host->pmecc_lmu = devm_kzalloc(host->dev,
524 (cap + 1) * sizeof(int16_t), GFP_KERNEL);
525 host->pmecc_smu = devm_kzalloc(host->dev,
526 (cap + 2) * size, GFP_KERNEL);
528 size = (cap + 1) * sizeof(int);
529 host->pmecc_mu = devm_kzalloc(host->dev, size, GFP_KERNEL);
530 host->pmecc_dmu = devm_kzalloc(host->dev, size, GFP_KERNEL);
531 host->pmecc_delta = devm_kzalloc(host->dev, size, GFP_KERNEL);
533 if (!host->pmecc_partial_syn ||
534 !host->pmecc_si ||
535 !host->pmecc_lmu ||
536 !host->pmecc_smu ||
537 !host->pmecc_mu ||
538 !host->pmecc_dmu ||
539 !host->pmecc_delta)
540 return -ENOMEM;
542 return 0;
545 static void pmecc_gen_syndrome(struct mtd_info *mtd, int sector)
547 struct nand_chip *nand_chip = mtd->priv;
548 struct atmel_nand_host *host = nand_chip->priv;
549 int i;
550 uint32_t value;
552 /* Fill odd syndromes */
553 for (i = 0; i < host->pmecc_corr_cap; i++) {
554 value = pmecc_readl_rem_relaxed(host->ecc, sector, i / 2);
555 if (i & 1)
556 value >>= 16;
557 value &= 0xffff;
558 host->pmecc_partial_syn[(2 * i) + 1] = (int16_t)value;
562 static void pmecc_substitute(struct mtd_info *mtd)
564 struct nand_chip *nand_chip = mtd->priv;
565 struct atmel_nand_host *host = nand_chip->priv;
566 int16_t __iomem *alpha_to = host->pmecc_alpha_to;
567 int16_t __iomem *index_of = host->pmecc_index_of;
568 int16_t *partial_syn = host->pmecc_partial_syn;
569 const int cap = host->pmecc_corr_cap;
570 int16_t *si;
571 int i, j;
573 /* si[] is a table that holds the current syndrome value,
574 * an element of that table belongs to the field
576 si = host->pmecc_si;
578 memset(&si[1], 0, sizeof(int16_t) * (2 * cap - 1));
580 /* Computation 2t syndromes based on S(x) */
581 /* Odd syndromes */
582 for (i = 1; i < 2 * cap; i += 2) {
583 for (j = 0; j < host->pmecc_degree; j++) {
584 if (partial_syn[i] & ((unsigned short)0x1 << j))
585 si[i] = readw_relaxed(alpha_to + i * j) ^ si[i];
588 /* Even syndrome = (Odd syndrome) ** 2 */
589 for (i = 2, j = 1; j <= cap; i = ++j << 1) {
590 if (si[j] == 0) {
591 si[i] = 0;
592 } else {
593 int16_t tmp;
595 tmp = readw_relaxed(index_of + si[j]);
596 tmp = (tmp * 2) % host->pmecc_cw_len;
597 si[i] = readw_relaxed(alpha_to + tmp);
601 return;
604 static void pmecc_get_sigma(struct mtd_info *mtd)
606 struct nand_chip *nand_chip = mtd->priv;
607 struct atmel_nand_host *host = nand_chip->priv;
609 int16_t *lmu = host->pmecc_lmu;
610 int16_t *si = host->pmecc_si;
611 int *mu = host->pmecc_mu;
612 int *dmu = host->pmecc_dmu; /* Discrepancy */
613 int *delta = host->pmecc_delta; /* Delta order */
614 int cw_len = host->pmecc_cw_len;
615 const int16_t cap = host->pmecc_corr_cap;
616 const int num = 2 * cap + 1;
617 int16_t __iomem *index_of = host->pmecc_index_of;
618 int16_t __iomem *alpha_to = host->pmecc_alpha_to;
619 int i, j, k;
620 uint32_t dmu_0_count, tmp;
621 int16_t *smu = host->pmecc_smu;
623 /* index of largest delta */
624 int ro;
625 int largest;
626 int diff;
628 dmu_0_count = 0;
630 /* First Row */
632 /* Mu */
633 mu[0] = -1;
635 memset(smu, 0, sizeof(int16_t) * num);
636 smu[0] = 1;
638 /* discrepancy set to 1 */
639 dmu[0] = 1;
640 /* polynom order set to 0 */
641 lmu[0] = 0;
642 delta[0] = (mu[0] * 2 - lmu[0]) >> 1;
644 /* Second Row */
646 /* Mu */
647 mu[1] = 0;
648 /* Sigma(x) set to 1 */
649 memset(&smu[num], 0, sizeof(int16_t) * num);
650 smu[num] = 1;
652 /* discrepancy set to S1 */
653 dmu[1] = si[1];
655 /* polynom order set to 0 */
656 lmu[1] = 0;
658 delta[1] = (mu[1] * 2 - lmu[1]) >> 1;
660 /* Init the Sigma(x) last row */
661 memset(&smu[(cap + 1) * num], 0, sizeof(int16_t) * num);
663 for (i = 1; i <= cap; i++) {
664 mu[i + 1] = i << 1;
665 /* Begin Computing Sigma (Mu+1) and L(mu) */
666 /* check if discrepancy is set to 0 */
667 if (dmu[i] == 0) {
668 dmu_0_count++;
670 tmp = ((cap - (lmu[i] >> 1) - 1) / 2);
671 if ((cap - (lmu[i] >> 1) - 1) & 0x1)
672 tmp += 2;
673 else
674 tmp += 1;
676 if (dmu_0_count == tmp) {
677 for (j = 0; j <= (lmu[i] >> 1) + 1; j++)
678 smu[(cap + 1) * num + j] =
679 smu[i * num + j];
681 lmu[cap + 1] = lmu[i];
682 return;
685 /* copy polynom */
686 for (j = 0; j <= lmu[i] >> 1; j++)
687 smu[(i + 1) * num + j] = smu[i * num + j];
689 /* copy previous polynom order to the next */
690 lmu[i + 1] = lmu[i];
691 } else {
692 ro = 0;
693 largest = -1;
694 /* find largest delta with dmu != 0 */
695 for (j = 0; j < i; j++) {
696 if ((dmu[j]) && (delta[j] > largest)) {
697 largest = delta[j];
698 ro = j;
702 /* compute difference */
703 diff = (mu[i] - mu[ro]);
705 /* Compute degree of the new smu polynomial */
706 if ((lmu[i] >> 1) > ((lmu[ro] >> 1) + diff))
707 lmu[i + 1] = lmu[i];
708 else
709 lmu[i + 1] = ((lmu[ro] >> 1) + diff) * 2;
711 /* Init smu[i+1] with 0 */
712 for (k = 0; k < num; k++)
713 smu[(i + 1) * num + k] = 0;
715 /* Compute smu[i+1] */
716 for (k = 0; k <= lmu[ro] >> 1; k++) {
717 int16_t a, b, c;
719 if (!(smu[ro * num + k] && dmu[i]))
720 continue;
721 a = readw_relaxed(index_of + dmu[i]);
722 b = readw_relaxed(index_of + dmu[ro]);
723 c = readw_relaxed(index_of + smu[ro * num + k]);
724 tmp = a + (cw_len - b) + c;
725 a = readw_relaxed(alpha_to + tmp % cw_len);
726 smu[(i + 1) * num + (k + diff)] = a;
729 for (k = 0; k <= lmu[i] >> 1; k++)
730 smu[(i + 1) * num + k] ^= smu[i * num + k];
733 /* End Computing Sigma (Mu+1) and L(mu) */
734 /* In either case compute delta */
735 delta[i + 1] = (mu[i + 1] * 2 - lmu[i + 1]) >> 1;
737 /* Do not compute discrepancy for the last iteration */
738 if (i >= cap)
739 continue;
741 for (k = 0; k <= (lmu[i + 1] >> 1); k++) {
742 tmp = 2 * (i - 1);
743 if (k == 0) {
744 dmu[i + 1] = si[tmp + 3];
745 } else if (smu[(i + 1) * num + k] && si[tmp + 3 - k]) {
746 int16_t a, b, c;
747 a = readw_relaxed(index_of +
748 smu[(i + 1) * num + k]);
749 b = si[2 * (i - 1) + 3 - k];
750 c = readw_relaxed(index_of + b);
751 tmp = a + c;
752 tmp %= cw_len;
753 dmu[i + 1] = readw_relaxed(alpha_to + tmp) ^
754 dmu[i + 1];
759 return;
762 static int pmecc_err_location(struct mtd_info *mtd)
764 struct nand_chip *nand_chip = mtd->priv;
765 struct atmel_nand_host *host = nand_chip->priv;
766 unsigned long end_time;
767 const int cap = host->pmecc_corr_cap;
768 const int num = 2 * cap + 1;
769 int sector_size = host->pmecc_sector_size;
770 int err_nbr = 0; /* number of error */
771 int roots_nbr; /* number of roots */
772 int i;
773 uint32_t val;
774 int16_t *smu = host->pmecc_smu;
776 pmerrloc_writel(host->pmerrloc_base, ELDIS, PMERRLOC_DISABLE);
778 for (i = 0; i <= host->pmecc_lmu[cap + 1] >> 1; i++) {
779 pmerrloc_writel_sigma_relaxed(host->pmerrloc_base, i,
780 smu[(cap + 1) * num + i]);
781 err_nbr++;
784 val = (err_nbr - 1) << 16;
785 if (sector_size == 1024)
786 val |= 1;
788 pmerrloc_writel(host->pmerrloc_base, ELCFG, val);
789 pmerrloc_writel(host->pmerrloc_base, ELEN,
790 sector_size * 8 + host->pmecc_degree * cap);
792 end_time = jiffies + msecs_to_jiffies(PMECC_MAX_TIMEOUT_MS);
793 while (!(pmerrloc_readl_relaxed(host->pmerrloc_base, ELISR)
794 & PMERRLOC_CALC_DONE)) {
795 if (unlikely(time_after(jiffies, end_time))) {
796 dev_err(host->dev, "PMECC: Timeout to calculate error location.\n");
797 return -1;
799 cpu_relax();
802 roots_nbr = (pmerrloc_readl_relaxed(host->pmerrloc_base, ELISR)
803 & PMERRLOC_ERR_NUM_MASK) >> 8;
804 /* Number of roots == degree of smu hence <= cap */
805 if (roots_nbr == host->pmecc_lmu[cap + 1] >> 1)
806 return err_nbr - 1;
808 /* Number of roots does not match the degree of smu
809 * unable to correct error */
810 return -1;
813 static void pmecc_correct_data(struct mtd_info *mtd, uint8_t *buf, uint8_t *ecc,
814 int sector_num, int extra_bytes, int err_nbr)
816 struct nand_chip *nand_chip = mtd->priv;
817 struct atmel_nand_host *host = nand_chip->priv;
818 int i = 0;
819 int byte_pos, bit_pos, sector_size, pos;
820 uint32_t tmp;
821 uint8_t err_byte;
823 sector_size = host->pmecc_sector_size;
825 while (err_nbr) {
826 tmp = pmerrloc_readl_el_relaxed(host->pmerrloc_base, i) - 1;
827 byte_pos = tmp / 8;
828 bit_pos = tmp % 8;
830 if (byte_pos >= (sector_size + extra_bytes))
831 BUG(); /* should never happen */
833 if (byte_pos < sector_size) {
834 err_byte = *(buf + byte_pos);
835 *(buf + byte_pos) ^= (1 << bit_pos);
837 pos = sector_num * host->pmecc_sector_size + byte_pos;
838 dev_info(host->dev, "Bit flip in data area, byte_pos: %d, bit_pos: %d, 0x%02x -> 0x%02x\n",
839 pos, bit_pos, err_byte, *(buf + byte_pos));
840 } else {
841 /* Bit flip in OOB area */
842 tmp = sector_num * host->pmecc_bytes_per_sector
843 + (byte_pos - sector_size);
844 err_byte = ecc[tmp];
845 ecc[tmp] ^= (1 << bit_pos);
847 pos = tmp + nand_chip->ecc.layout->eccpos[0];
848 dev_info(host->dev, "Bit flip in OOB, oob_byte_pos: %d, bit_pos: %d, 0x%02x -> 0x%02x\n",
849 pos, bit_pos, err_byte, ecc[tmp]);
852 i++;
853 err_nbr--;
856 return;
859 static int pmecc_correction(struct mtd_info *mtd, u32 pmecc_stat, uint8_t *buf,
860 u8 *ecc)
862 struct nand_chip *nand_chip = mtd->priv;
863 struct atmel_nand_host *host = nand_chip->priv;
864 int i, err_nbr, eccbytes;
865 uint8_t *buf_pos;
866 int total_err = 0;
868 eccbytes = nand_chip->ecc.bytes;
869 for (i = 0; i < eccbytes; i++)
870 if (ecc[i] != 0xff)
871 goto normal_check;
872 /* Erased page, return OK */
873 return 0;
875 normal_check:
876 for (i = 0; i < host->pmecc_sector_number; i++) {
877 err_nbr = 0;
878 if (pmecc_stat & 0x1) {
879 buf_pos = buf + i * host->pmecc_sector_size;
881 pmecc_gen_syndrome(mtd, i);
882 pmecc_substitute(mtd);
883 pmecc_get_sigma(mtd);
885 err_nbr = pmecc_err_location(mtd);
886 if (err_nbr == -1) {
887 dev_err(host->dev, "PMECC: Too many errors\n");
888 mtd->ecc_stats.failed++;
889 return -EIO;
890 } else {
891 pmecc_correct_data(mtd, buf_pos, ecc, i,
892 host->pmecc_bytes_per_sector, err_nbr);
893 mtd->ecc_stats.corrected += err_nbr;
894 total_err += err_nbr;
897 pmecc_stat >>= 1;
900 return total_err;
903 static void pmecc_enable(struct atmel_nand_host *host, int ecc_op)
905 u32 val;
907 if (ecc_op != NAND_ECC_READ && ecc_op != NAND_ECC_WRITE) {
908 dev_err(host->dev, "atmel_nand: wrong pmecc operation type!");
909 return;
912 pmecc_writel(host->ecc, CTRL, PMECC_CTRL_RST);
913 pmecc_writel(host->ecc, CTRL, PMECC_CTRL_DISABLE);
914 val = pmecc_readl_relaxed(host->ecc, CFG);
916 if (ecc_op == NAND_ECC_READ)
917 pmecc_writel(host->ecc, CFG, (val & ~PMECC_CFG_WRITE_OP)
918 | PMECC_CFG_AUTO_ENABLE);
919 else
920 pmecc_writel(host->ecc, CFG, (val | PMECC_CFG_WRITE_OP)
921 & ~PMECC_CFG_AUTO_ENABLE);
923 pmecc_writel(host->ecc, CTRL, PMECC_CTRL_ENABLE);
924 pmecc_writel(host->ecc, CTRL, PMECC_CTRL_DATA);
927 static int atmel_nand_pmecc_read_page(struct mtd_info *mtd,
928 struct nand_chip *chip, uint8_t *buf, int oob_required, int page)
930 struct atmel_nand_host *host = chip->priv;
931 int eccsize = chip->ecc.size;
932 uint8_t *oob = chip->oob_poi;
933 uint32_t *eccpos = chip->ecc.layout->eccpos;
934 uint32_t stat;
935 unsigned long end_time;
936 int bitflips = 0;
938 if (!host->nfc || !host->nfc->use_nfc_sram)
939 pmecc_enable(host, NAND_ECC_READ);
941 chip->read_buf(mtd, buf, eccsize);
942 chip->read_buf(mtd, oob, mtd->oobsize);
944 end_time = jiffies + msecs_to_jiffies(PMECC_MAX_TIMEOUT_MS);
945 while ((pmecc_readl_relaxed(host->ecc, SR) & PMECC_SR_BUSY)) {
946 if (unlikely(time_after(jiffies, end_time))) {
947 dev_err(host->dev, "PMECC: Timeout to get error status.\n");
948 return -EIO;
950 cpu_relax();
953 stat = pmecc_readl_relaxed(host->ecc, ISR);
954 if (stat != 0) {
955 bitflips = pmecc_correction(mtd, stat, buf, &oob[eccpos[0]]);
956 if (bitflips < 0)
957 /* uncorrectable errors */
958 return 0;
961 return bitflips;
964 static int atmel_nand_pmecc_write_page(struct mtd_info *mtd,
965 struct nand_chip *chip, const uint8_t *buf, int oob_required)
967 struct atmel_nand_host *host = chip->priv;
968 uint32_t *eccpos = chip->ecc.layout->eccpos;
969 int i, j;
970 unsigned long end_time;
972 if (!host->nfc || !host->nfc->write_by_sram) {
973 pmecc_enable(host, NAND_ECC_WRITE);
974 chip->write_buf(mtd, (u8 *)buf, mtd->writesize);
977 end_time = jiffies + msecs_to_jiffies(PMECC_MAX_TIMEOUT_MS);
978 while ((pmecc_readl_relaxed(host->ecc, SR) & PMECC_SR_BUSY)) {
979 if (unlikely(time_after(jiffies, end_time))) {
980 dev_err(host->dev, "PMECC: Timeout to get ECC value.\n");
981 return -EIO;
983 cpu_relax();
986 for (i = 0; i < host->pmecc_sector_number; i++) {
987 for (j = 0; j < host->pmecc_bytes_per_sector; j++) {
988 int pos;
990 pos = i * host->pmecc_bytes_per_sector + j;
991 chip->oob_poi[eccpos[pos]] =
992 pmecc_readb_ecc_relaxed(host->ecc, i, j);
995 chip->write_buf(mtd, chip->oob_poi, mtd->oobsize);
997 return 0;
1000 static void atmel_pmecc_core_init(struct mtd_info *mtd)
1002 struct nand_chip *nand_chip = mtd->priv;
1003 struct atmel_nand_host *host = nand_chip->priv;
1004 uint32_t val = 0;
1005 struct nand_ecclayout *ecc_layout;
1007 pmecc_writel(host->ecc, CTRL, PMECC_CTRL_RST);
1008 pmecc_writel(host->ecc, CTRL, PMECC_CTRL_DISABLE);
1010 switch (host->pmecc_corr_cap) {
1011 case 2:
1012 val = PMECC_CFG_BCH_ERR2;
1013 break;
1014 case 4:
1015 val = PMECC_CFG_BCH_ERR4;
1016 break;
1017 case 8:
1018 val = PMECC_CFG_BCH_ERR8;
1019 break;
1020 case 12:
1021 val = PMECC_CFG_BCH_ERR12;
1022 break;
1023 case 24:
1024 val = PMECC_CFG_BCH_ERR24;
1025 break;
1028 if (host->pmecc_sector_size == 512)
1029 val |= PMECC_CFG_SECTOR512;
1030 else if (host->pmecc_sector_size == 1024)
1031 val |= PMECC_CFG_SECTOR1024;
1033 switch (host->pmecc_sector_number) {
1034 case 1:
1035 val |= PMECC_CFG_PAGE_1SECTOR;
1036 break;
1037 case 2:
1038 val |= PMECC_CFG_PAGE_2SECTORS;
1039 break;
1040 case 4:
1041 val |= PMECC_CFG_PAGE_4SECTORS;
1042 break;
1043 case 8:
1044 val |= PMECC_CFG_PAGE_8SECTORS;
1045 break;
1048 val |= (PMECC_CFG_READ_OP | PMECC_CFG_SPARE_DISABLE
1049 | PMECC_CFG_AUTO_DISABLE);
1050 pmecc_writel(host->ecc, CFG, val);
1052 ecc_layout = nand_chip->ecc.layout;
1053 pmecc_writel(host->ecc, SAREA, mtd->oobsize - 1);
1054 pmecc_writel(host->ecc, SADDR, ecc_layout->eccpos[0]);
1055 pmecc_writel(host->ecc, EADDR,
1056 ecc_layout->eccpos[ecc_layout->eccbytes - 1]);
1057 /* See datasheet about PMECC Clock Control Register */
1058 pmecc_writel(host->ecc, CLK, 2);
1059 pmecc_writel(host->ecc, IDR, 0xff);
1060 pmecc_writel(host->ecc, CTRL, PMECC_CTRL_ENABLE);
1064 * Get minimum ecc requirements from NAND.
1065 * If pmecc-cap, pmecc-sector-size in DTS are not specified, this function
1066 * will set them according to minimum ecc requirement. Otherwise, use the
1067 * value in DTS file.
1068 * return 0 if success. otherwise return error code.
1070 static int pmecc_choose_ecc(struct atmel_nand_host *host,
1071 int *cap, int *sector_size)
1073 /* Get minimum ECC requirements */
1074 if (host->nand_chip.ecc_strength_ds) {
1075 *cap = host->nand_chip.ecc_strength_ds;
1076 *sector_size = host->nand_chip.ecc_step_ds;
1077 dev_info(host->dev, "minimum ECC: %d bits in %d bytes\n",
1078 *cap, *sector_size);
1079 } else {
1080 *cap = 2;
1081 *sector_size = 512;
1082 dev_info(host->dev, "can't detect min. ECC, assume 2 bits in 512 bytes\n");
1085 /* If device tree doesn't specify, use NAND's minimum ECC parameters */
1086 if (host->pmecc_corr_cap == 0) {
1087 /* use the most fitable ecc bits (the near bigger one ) */
1088 if (*cap <= 2)
1089 host->pmecc_corr_cap = 2;
1090 else if (*cap <= 4)
1091 host->pmecc_corr_cap = 4;
1092 else if (*cap <= 8)
1093 host->pmecc_corr_cap = 8;
1094 else if (*cap <= 12)
1095 host->pmecc_corr_cap = 12;
1096 else if (*cap <= 24)
1097 host->pmecc_corr_cap = 24;
1098 else
1099 return -EINVAL;
1101 if (host->pmecc_sector_size == 0) {
1102 /* use the most fitable sector size (the near smaller one ) */
1103 if (*sector_size >= 1024)
1104 host->pmecc_sector_size = 1024;
1105 else if (*sector_size >= 512)
1106 host->pmecc_sector_size = 512;
1107 else
1108 return -EINVAL;
1110 return 0;
1113 static int atmel_pmecc_nand_init_params(struct platform_device *pdev,
1114 struct atmel_nand_host *host)
1116 struct mtd_info *mtd = &host->mtd;
1117 struct nand_chip *nand_chip = &host->nand_chip;
1118 struct resource *regs, *regs_pmerr, *regs_rom;
1119 int cap, sector_size, err_no;
1121 err_no = pmecc_choose_ecc(host, &cap, &sector_size);
1122 if (err_no) {
1123 dev_err(host->dev, "The NAND flash's ECC requirement are not support!");
1124 return err_no;
1127 if (cap > host->pmecc_corr_cap ||
1128 sector_size != host->pmecc_sector_size)
1129 dev_info(host->dev, "WARNING: Be Caution! Using different PMECC parameters from Nand ONFI ECC reqirement.\n");
1131 cap = host->pmecc_corr_cap;
1132 sector_size = host->pmecc_sector_size;
1133 host->pmecc_lookup_table_offset = (sector_size == 512) ?
1134 host->pmecc_lookup_table_offset_512 :
1135 host->pmecc_lookup_table_offset_1024;
1137 dev_info(host->dev, "Initialize PMECC params, cap: %d, sector: %d\n",
1138 cap, sector_size);
1140 regs = platform_get_resource(pdev, IORESOURCE_MEM, 1);
1141 if (!regs) {
1142 dev_warn(host->dev,
1143 "Can't get I/O resource regs for PMECC controller, rolling back on software ECC\n");
1144 nand_chip->ecc.mode = NAND_ECC_SOFT;
1145 return 0;
1148 host->ecc = devm_ioremap_resource(&pdev->dev, regs);
1149 if (IS_ERR(host->ecc)) {
1150 dev_err(host->dev, "ioremap failed\n");
1151 err_no = PTR_ERR(host->ecc);
1152 goto err;
1155 regs_pmerr = platform_get_resource(pdev, IORESOURCE_MEM, 2);
1156 host->pmerrloc_base = devm_ioremap_resource(&pdev->dev, regs_pmerr);
1157 if (IS_ERR(host->pmerrloc_base)) {
1158 dev_err(host->dev,
1159 "Can not get I/O resource for PMECC ERRLOC controller!\n");
1160 err_no = PTR_ERR(host->pmerrloc_base);
1161 goto err;
1164 regs_rom = platform_get_resource(pdev, IORESOURCE_MEM, 3);
1165 host->pmecc_rom_base = devm_ioremap_resource(&pdev->dev, regs_rom);
1166 if (IS_ERR(host->pmecc_rom_base)) {
1167 dev_err(host->dev, "Can not get I/O resource for ROM!\n");
1168 err_no = PTR_ERR(host->pmecc_rom_base);
1169 goto err;
1172 /* ECC is calculated for the whole page (1 step) */
1173 nand_chip->ecc.size = mtd->writesize;
1175 /* set ECC page size and oob layout */
1176 switch (mtd->writesize) {
1177 case 2048:
1178 host->pmecc_degree = (sector_size == 512) ?
1179 PMECC_GF_DIMENSION_13 : PMECC_GF_DIMENSION_14;
1180 host->pmecc_cw_len = (1 << host->pmecc_degree) - 1;
1181 host->pmecc_sector_number = mtd->writesize / sector_size;
1182 host->pmecc_bytes_per_sector = pmecc_get_ecc_bytes(
1183 cap, sector_size);
1184 host->pmecc_alpha_to = pmecc_get_alpha_to(host);
1185 host->pmecc_index_of = host->pmecc_rom_base +
1186 host->pmecc_lookup_table_offset;
1188 nand_chip->ecc.steps = 1;
1189 nand_chip->ecc.strength = cap;
1190 nand_chip->ecc.bytes = host->pmecc_bytes_per_sector *
1191 host->pmecc_sector_number;
1192 if (nand_chip->ecc.bytes > mtd->oobsize - 2) {
1193 dev_err(host->dev, "No room for ECC bytes\n");
1194 err_no = -EINVAL;
1195 goto err;
1197 pmecc_config_ecc_layout(&atmel_pmecc_oobinfo,
1198 mtd->oobsize,
1199 nand_chip->ecc.bytes);
1200 nand_chip->ecc.layout = &atmel_pmecc_oobinfo;
1201 break;
1202 case 512:
1203 case 1024:
1204 case 4096:
1205 /* TODO */
1206 dev_warn(host->dev,
1207 "Unsupported page size for PMECC, use Software ECC\n");
1208 default:
1209 /* page size not handled by HW ECC */
1210 /* switching back to soft ECC */
1211 nand_chip->ecc.mode = NAND_ECC_SOFT;
1212 return 0;
1215 /* Allocate data for PMECC computation */
1216 err_no = pmecc_data_alloc(host);
1217 if (err_no) {
1218 dev_err(host->dev,
1219 "Cannot allocate memory for PMECC computation!\n");
1220 goto err;
1223 nand_chip->options |= NAND_NO_SUBPAGE_WRITE;
1224 nand_chip->ecc.read_page = atmel_nand_pmecc_read_page;
1225 nand_chip->ecc.write_page = atmel_nand_pmecc_write_page;
1227 atmel_pmecc_core_init(mtd);
1229 return 0;
1231 err:
1232 return err_no;
1236 * Calculate HW ECC
1238 * function called after a write
1240 * mtd: MTD block structure
1241 * dat: raw data (unused)
1242 * ecc_code: buffer for ECC
1244 static int atmel_nand_calculate(struct mtd_info *mtd,
1245 const u_char *dat, unsigned char *ecc_code)
1247 struct nand_chip *nand_chip = mtd->priv;
1248 struct atmel_nand_host *host = nand_chip->priv;
1249 unsigned int ecc_value;
1251 /* get the first 2 ECC bytes */
1252 ecc_value = ecc_readl(host->ecc, PR);
1254 ecc_code[0] = ecc_value & 0xFF;
1255 ecc_code[1] = (ecc_value >> 8) & 0xFF;
1257 /* get the last 2 ECC bytes */
1258 ecc_value = ecc_readl(host->ecc, NPR) & ATMEL_ECC_NPARITY;
1260 ecc_code[2] = ecc_value & 0xFF;
1261 ecc_code[3] = (ecc_value >> 8) & 0xFF;
1263 return 0;
1267 * HW ECC read page function
1269 * mtd: mtd info structure
1270 * chip: nand chip info structure
1271 * buf: buffer to store read data
1272 * oob_required: caller expects OOB data read to chip->oob_poi
1274 static int atmel_nand_read_page(struct mtd_info *mtd, struct nand_chip *chip,
1275 uint8_t *buf, int oob_required, int page)
1277 int eccsize = chip->ecc.size;
1278 int eccbytes = chip->ecc.bytes;
1279 uint32_t *eccpos = chip->ecc.layout->eccpos;
1280 uint8_t *p = buf;
1281 uint8_t *oob = chip->oob_poi;
1282 uint8_t *ecc_pos;
1283 int stat;
1284 unsigned int max_bitflips = 0;
1287 * Errata: ALE is incorrectly wired up to the ECC controller
1288 * on the AP7000, so it will include the address cycles in the
1289 * ECC calculation.
1291 * Workaround: Reset the parity registers before reading the
1292 * actual data.
1294 struct atmel_nand_host *host = chip->priv;
1295 if (host->board.need_reset_workaround)
1296 ecc_writel(host->ecc, CR, ATMEL_ECC_RST);
1298 /* read the page */
1299 chip->read_buf(mtd, p, eccsize);
1301 /* move to ECC position if needed */
1302 if (eccpos[0] != 0) {
1303 /* This only works on large pages
1304 * because the ECC controller waits for
1305 * NAND_CMD_RNDOUTSTART after the
1306 * NAND_CMD_RNDOUT.
1307 * anyway, for small pages, the eccpos[0] == 0
1309 chip->cmdfunc(mtd, NAND_CMD_RNDOUT,
1310 mtd->writesize + eccpos[0], -1);
1313 /* the ECC controller needs to read the ECC just after the data */
1314 ecc_pos = oob + eccpos[0];
1315 chip->read_buf(mtd, ecc_pos, eccbytes);
1317 /* check if there's an error */
1318 stat = chip->ecc.correct(mtd, p, oob, NULL);
1320 if (stat < 0) {
1321 mtd->ecc_stats.failed++;
1322 } else {
1323 mtd->ecc_stats.corrected += stat;
1324 max_bitflips = max_t(unsigned int, max_bitflips, stat);
1327 /* get back to oob start (end of page) */
1328 chip->cmdfunc(mtd, NAND_CMD_RNDOUT, mtd->writesize, -1);
1330 /* read the oob */
1331 chip->read_buf(mtd, oob, mtd->oobsize);
1333 return max_bitflips;
1337 * HW ECC Correction
1339 * function called after a read
1341 * mtd: MTD block structure
1342 * dat: raw data read from the chip
1343 * read_ecc: ECC from the chip (unused)
1344 * isnull: unused
1346 * Detect and correct a 1 bit error for a page
1348 static int atmel_nand_correct(struct mtd_info *mtd, u_char *dat,
1349 u_char *read_ecc, u_char *isnull)
1351 struct nand_chip *nand_chip = mtd->priv;
1352 struct atmel_nand_host *host = nand_chip->priv;
1353 unsigned int ecc_status;
1354 unsigned int ecc_word, ecc_bit;
1356 /* get the status from the Status Register */
1357 ecc_status = ecc_readl(host->ecc, SR);
1359 /* if there's no error */
1360 if (likely(!(ecc_status & ATMEL_ECC_RECERR)))
1361 return 0;
1363 /* get error bit offset (4 bits) */
1364 ecc_bit = ecc_readl(host->ecc, PR) & ATMEL_ECC_BITADDR;
1365 /* get word address (12 bits) */
1366 ecc_word = ecc_readl(host->ecc, PR) & ATMEL_ECC_WORDADDR;
1367 ecc_word >>= 4;
1369 /* if there are multiple errors */
1370 if (ecc_status & ATMEL_ECC_MULERR) {
1371 /* check if it is a freshly erased block
1372 * (filled with 0xff) */
1373 if ((ecc_bit == ATMEL_ECC_BITADDR)
1374 && (ecc_word == (ATMEL_ECC_WORDADDR >> 4))) {
1375 /* the block has just been erased, return OK */
1376 return 0;
1378 /* it doesn't seems to be a freshly
1379 * erased block.
1380 * We can't correct so many errors */
1381 dev_dbg(host->dev, "atmel_nand : multiple errors detected."
1382 " Unable to correct.\n");
1383 return -EIO;
1386 /* if there's a single bit error : we can correct it */
1387 if (ecc_status & ATMEL_ECC_ECCERR) {
1388 /* there's nothing much to do here.
1389 * the bit error is on the ECC itself.
1391 dev_dbg(host->dev, "atmel_nand : one bit error on ECC code."
1392 " Nothing to correct\n");
1393 return 0;
1396 dev_dbg(host->dev, "atmel_nand : one bit error on data."
1397 " (word offset in the page :"
1398 " 0x%x bit offset : 0x%x)\n",
1399 ecc_word, ecc_bit);
1400 /* correct the error */
1401 if (nand_chip->options & NAND_BUSWIDTH_16) {
1402 /* 16 bits words */
1403 ((unsigned short *) dat)[ecc_word] ^= (1 << ecc_bit);
1404 } else {
1405 /* 8 bits words */
1406 dat[ecc_word] ^= (1 << ecc_bit);
1408 dev_dbg(host->dev, "atmel_nand : error corrected\n");
1409 return 1;
1413 * Enable HW ECC : unused on most chips
1415 static void atmel_nand_hwctl(struct mtd_info *mtd, int mode)
1417 struct nand_chip *nand_chip = mtd->priv;
1418 struct atmel_nand_host *host = nand_chip->priv;
1420 if (host->board.need_reset_workaround)
1421 ecc_writel(host->ecc, CR, ATMEL_ECC_RST);
1424 static int atmel_of_init_port(struct atmel_nand_host *host,
1425 struct device_node *np)
1427 u32 val;
1428 u32 offset[2];
1429 int ecc_mode;
1430 struct atmel_nand_data *board = &host->board;
1431 enum of_gpio_flags flags = 0;
1433 if (of_property_read_u32(np, "atmel,nand-addr-offset", &val) == 0) {
1434 if (val >= 32) {
1435 dev_err(host->dev, "invalid addr-offset %u\n", val);
1436 return -EINVAL;
1438 board->ale = val;
1441 if (of_property_read_u32(np, "atmel,nand-cmd-offset", &val) == 0) {
1442 if (val >= 32) {
1443 dev_err(host->dev, "invalid cmd-offset %u\n", val);
1444 return -EINVAL;
1446 board->cle = val;
1449 ecc_mode = of_get_nand_ecc_mode(np);
1451 board->ecc_mode = ecc_mode < 0 ? NAND_ECC_SOFT : ecc_mode;
1453 board->on_flash_bbt = of_get_nand_on_flash_bbt(np);
1455 board->has_dma = of_property_read_bool(np, "atmel,nand-has-dma");
1457 if (of_get_nand_bus_width(np) == 16)
1458 board->bus_width_16 = 1;
1460 board->rdy_pin = of_get_gpio_flags(np, 0, &flags);
1461 board->rdy_pin_active_low = (flags == OF_GPIO_ACTIVE_LOW);
1463 board->enable_pin = of_get_gpio(np, 1);
1464 board->det_pin = of_get_gpio(np, 2);
1466 host->has_pmecc = of_property_read_bool(np, "atmel,has-pmecc");
1468 /* load the nfc driver if there is */
1469 of_platform_populate(np, NULL, NULL, host->dev);
1471 if (!(board->ecc_mode == NAND_ECC_HW) || !host->has_pmecc)
1472 return 0; /* Not using PMECC */
1474 /* use PMECC, get correction capability, sector size and lookup
1475 * table offset.
1476 * If correction bits and sector size are not specified, then find
1477 * them from NAND ONFI parameters.
1479 if (of_property_read_u32(np, "atmel,pmecc-cap", &val) == 0) {
1480 if ((val != 2) && (val != 4) && (val != 8) && (val != 12) &&
1481 (val != 24)) {
1482 dev_err(host->dev,
1483 "Unsupported PMECC correction capability: %d; should be 2, 4, 8, 12 or 24\n",
1484 val);
1485 return -EINVAL;
1487 host->pmecc_corr_cap = (u8)val;
1490 if (of_property_read_u32(np, "atmel,pmecc-sector-size", &val) == 0) {
1491 if ((val != 512) && (val != 1024)) {
1492 dev_err(host->dev,
1493 "Unsupported PMECC sector size: %d; should be 512 or 1024 bytes\n",
1494 val);
1495 return -EINVAL;
1497 host->pmecc_sector_size = (u16)val;
1500 if (of_property_read_u32_array(np, "atmel,pmecc-lookup-table-offset",
1501 offset, 2) != 0) {
1502 dev_err(host->dev, "Cannot get PMECC lookup table offset\n");
1503 return -EINVAL;
1505 if (!offset[0] && !offset[1]) {
1506 dev_err(host->dev, "Invalid PMECC lookup table offset\n");
1507 return -EINVAL;
1509 host->pmecc_lookup_table_offset_512 = offset[0];
1510 host->pmecc_lookup_table_offset_1024 = offset[1];
1512 return 0;
1515 static int atmel_hw_nand_init_params(struct platform_device *pdev,
1516 struct atmel_nand_host *host)
1518 struct mtd_info *mtd = &host->mtd;
1519 struct nand_chip *nand_chip = &host->nand_chip;
1520 struct resource *regs;
1522 regs = platform_get_resource(pdev, IORESOURCE_MEM, 1);
1523 if (!regs) {
1524 dev_err(host->dev,
1525 "Can't get I/O resource regs, use software ECC\n");
1526 nand_chip->ecc.mode = NAND_ECC_SOFT;
1527 return 0;
1530 host->ecc = devm_ioremap_resource(&pdev->dev, regs);
1531 if (IS_ERR(host->ecc)) {
1532 dev_err(host->dev, "ioremap failed\n");
1533 return PTR_ERR(host->ecc);
1536 /* ECC is calculated for the whole page (1 step) */
1537 nand_chip->ecc.size = mtd->writesize;
1539 /* set ECC page size and oob layout */
1540 switch (mtd->writesize) {
1541 case 512:
1542 nand_chip->ecc.layout = &atmel_oobinfo_small;
1543 ecc_writel(host->ecc, MR, ATMEL_ECC_PAGESIZE_528);
1544 break;
1545 case 1024:
1546 nand_chip->ecc.layout = &atmel_oobinfo_large;
1547 ecc_writel(host->ecc, MR, ATMEL_ECC_PAGESIZE_1056);
1548 break;
1549 case 2048:
1550 nand_chip->ecc.layout = &atmel_oobinfo_large;
1551 ecc_writel(host->ecc, MR, ATMEL_ECC_PAGESIZE_2112);
1552 break;
1553 case 4096:
1554 nand_chip->ecc.layout = &atmel_oobinfo_large;
1555 ecc_writel(host->ecc, MR, ATMEL_ECC_PAGESIZE_4224);
1556 break;
1557 default:
1558 /* page size not handled by HW ECC */
1559 /* switching back to soft ECC */
1560 nand_chip->ecc.mode = NAND_ECC_SOFT;
1561 return 0;
1564 /* set up for HW ECC */
1565 nand_chip->ecc.calculate = atmel_nand_calculate;
1566 nand_chip->ecc.correct = atmel_nand_correct;
1567 nand_chip->ecc.hwctl = atmel_nand_hwctl;
1568 nand_chip->ecc.read_page = atmel_nand_read_page;
1569 nand_chip->ecc.bytes = 4;
1570 nand_chip->ecc.strength = 1;
1572 return 0;
1575 /* SMC interrupt service routine */
1576 static irqreturn_t hsmc_interrupt(int irq, void *dev_id)
1578 struct atmel_nand_host *host = dev_id;
1579 u32 status, mask, pending;
1580 irqreturn_t ret = IRQ_HANDLED;
1582 status = nfc_readl(host->nfc->hsmc_regs, SR);
1583 mask = nfc_readl(host->nfc->hsmc_regs, IMR);
1584 pending = status & mask;
1586 if (pending & NFC_SR_XFR_DONE) {
1587 complete(&host->nfc->comp_nfc);
1588 nfc_writel(host->nfc->hsmc_regs, IDR, NFC_SR_XFR_DONE);
1589 } else if (pending & NFC_SR_RB_EDGE) {
1590 complete(&host->nfc->comp_nfc);
1591 nfc_writel(host->nfc->hsmc_regs, IDR, NFC_SR_RB_EDGE);
1592 } else if (pending & NFC_SR_CMD_DONE) {
1593 complete(&host->nfc->comp_nfc);
1594 nfc_writel(host->nfc->hsmc_regs, IDR, NFC_SR_CMD_DONE);
1595 } else {
1596 ret = IRQ_NONE;
1599 return ret;
1602 /* NFC(Nand Flash Controller) related functions */
1603 static int nfc_wait_interrupt(struct atmel_nand_host *host, u32 flag)
1605 unsigned long timeout;
1606 init_completion(&host->nfc->comp_nfc);
1608 /* Enable interrupt that need to wait for */
1609 nfc_writel(host->nfc->hsmc_regs, IER, flag);
1611 timeout = wait_for_completion_timeout(&host->nfc->comp_nfc,
1612 msecs_to_jiffies(NFC_TIME_OUT_MS));
1613 if (timeout)
1614 return 0;
1616 /* Time out to wait for the interrupt */
1617 dev_err(host->dev, "Time out to wait for interrupt: 0x%08x\n", flag);
1618 return -ETIMEDOUT;
1621 static int nfc_send_command(struct atmel_nand_host *host,
1622 unsigned int cmd, unsigned int addr, unsigned char cycle0)
1624 unsigned long timeout;
1625 dev_dbg(host->dev,
1626 "nfc_cmd: 0x%08x, addr1234: 0x%08x, cycle0: 0x%02x\n",
1627 cmd, addr, cycle0);
1629 timeout = jiffies + msecs_to_jiffies(NFC_TIME_OUT_MS);
1630 while (nfc_cmd_readl(NFCADDR_CMD_NFCBUSY, host->nfc->base_cmd_regs)
1631 & NFCADDR_CMD_NFCBUSY) {
1632 if (time_after(jiffies, timeout)) {
1633 dev_err(host->dev,
1634 "Time out to wait CMD_NFCBUSY ready!\n");
1635 return -ETIMEDOUT;
1638 nfc_writel(host->nfc->hsmc_regs, CYCLE0, cycle0);
1639 nfc_cmd_addr1234_writel(cmd, addr, host->nfc->base_cmd_regs);
1640 return nfc_wait_interrupt(host, NFC_SR_CMD_DONE);
1643 static int nfc_device_ready(struct mtd_info *mtd)
1645 struct nand_chip *nand_chip = mtd->priv;
1646 struct atmel_nand_host *host = nand_chip->priv;
1647 if (!nfc_wait_interrupt(host, NFC_SR_RB_EDGE))
1648 return 1;
1649 return 0;
1652 static void nfc_select_chip(struct mtd_info *mtd, int chip)
1654 struct nand_chip *nand_chip = mtd->priv;
1655 struct atmel_nand_host *host = nand_chip->priv;
1657 if (chip == -1)
1658 nfc_writel(host->nfc->hsmc_regs, CTRL, NFC_CTRL_DISABLE);
1659 else
1660 nfc_writel(host->nfc->hsmc_regs, CTRL, NFC_CTRL_ENABLE);
1663 static int nfc_make_addr(struct mtd_info *mtd, int command, int column,
1664 int page_addr, unsigned int *addr1234, unsigned int *cycle0)
1666 struct nand_chip *chip = mtd->priv;
1668 int acycle = 0;
1669 unsigned char addr_bytes[8];
1670 int index = 0, bit_shift;
1672 BUG_ON(addr1234 == NULL || cycle0 == NULL);
1674 *cycle0 = 0;
1675 *addr1234 = 0;
1677 if (column != -1) {
1678 if (chip->options & NAND_BUSWIDTH_16 &&
1679 !nand_opcode_8bits(command))
1680 column >>= 1;
1681 addr_bytes[acycle++] = column & 0xff;
1682 if (mtd->writesize > 512)
1683 addr_bytes[acycle++] = (column >> 8) & 0xff;
1686 if (page_addr != -1) {
1687 addr_bytes[acycle++] = page_addr & 0xff;
1688 addr_bytes[acycle++] = (page_addr >> 8) & 0xff;
1689 if (chip->chipsize > (128 << 20))
1690 addr_bytes[acycle++] = (page_addr >> 16) & 0xff;
1693 if (acycle > 4)
1694 *cycle0 = addr_bytes[index++];
1696 for (bit_shift = 0; index < acycle; bit_shift += 8)
1697 *addr1234 += addr_bytes[index++] << bit_shift;
1699 /* return acycle in cmd register */
1700 return acycle << NFCADDR_CMD_ACYCLE_BIT_POS;
1703 static void nfc_nand_command(struct mtd_info *mtd, unsigned int command,
1704 int column, int page_addr)
1706 struct nand_chip *chip = mtd->priv;
1707 struct atmel_nand_host *host = chip->priv;
1708 unsigned long timeout;
1709 unsigned int nfc_addr_cmd = 0;
1711 unsigned int cmd1 = command << NFCADDR_CMD_CMD1_BIT_POS;
1713 /* Set default settings: no cmd2, no addr cycle. read from nand */
1714 unsigned int cmd2 = 0;
1715 unsigned int vcmd2 = 0;
1716 int acycle = NFCADDR_CMD_ACYCLE_NONE;
1717 int csid = NFCADDR_CMD_CSID_3;
1718 int dataen = NFCADDR_CMD_DATADIS;
1719 int nfcwr = NFCADDR_CMD_NFCRD;
1720 unsigned int addr1234 = 0;
1721 unsigned int cycle0 = 0;
1722 bool do_addr = true;
1723 host->nfc->data_in_sram = NULL;
1725 dev_dbg(host->dev, "%s: cmd = 0x%02x, col = 0x%08x, page = 0x%08x\n",
1726 __func__, command, column, page_addr);
1728 switch (command) {
1729 case NAND_CMD_RESET:
1730 nfc_addr_cmd = cmd1 | acycle | csid | dataen | nfcwr;
1731 nfc_send_command(host, nfc_addr_cmd, addr1234, cycle0);
1732 udelay(chip->chip_delay);
1734 nfc_nand_command(mtd, NAND_CMD_STATUS, -1, -1);
1735 timeout = jiffies + msecs_to_jiffies(NFC_TIME_OUT_MS);
1736 while (!(chip->read_byte(mtd) & NAND_STATUS_READY)) {
1737 if (time_after(jiffies, timeout)) {
1738 dev_err(host->dev,
1739 "Time out to wait status ready!\n");
1740 break;
1743 return;
1744 case NAND_CMD_STATUS:
1745 do_addr = false;
1746 break;
1747 case NAND_CMD_PARAM:
1748 case NAND_CMD_READID:
1749 do_addr = false;
1750 acycle = NFCADDR_CMD_ACYCLE_1;
1751 if (column != -1)
1752 addr1234 = column;
1753 break;
1754 case NAND_CMD_RNDOUT:
1755 cmd2 = NAND_CMD_RNDOUTSTART << NFCADDR_CMD_CMD2_BIT_POS;
1756 vcmd2 = NFCADDR_CMD_VCMD2;
1757 break;
1758 case NAND_CMD_READ0:
1759 case NAND_CMD_READOOB:
1760 if (command == NAND_CMD_READOOB) {
1761 column += mtd->writesize;
1762 command = NAND_CMD_READ0; /* only READ0 is valid */
1763 cmd1 = command << NFCADDR_CMD_CMD1_BIT_POS;
1765 if (host->nfc->use_nfc_sram) {
1766 /* Enable Data transfer to sram */
1767 dataen = NFCADDR_CMD_DATAEN;
1769 /* Need enable PMECC now, since NFC will transfer
1770 * data in bus after sending nfc read command.
1772 if (chip->ecc.mode == NAND_ECC_HW && host->has_pmecc)
1773 pmecc_enable(host, NAND_ECC_READ);
1776 cmd2 = NAND_CMD_READSTART << NFCADDR_CMD_CMD2_BIT_POS;
1777 vcmd2 = NFCADDR_CMD_VCMD2;
1778 break;
1779 /* For prgramming command, the cmd need set to write enable */
1780 case NAND_CMD_PAGEPROG:
1781 case NAND_CMD_SEQIN:
1782 case NAND_CMD_RNDIN:
1783 nfcwr = NFCADDR_CMD_NFCWR;
1784 if (host->nfc->will_write_sram && command == NAND_CMD_SEQIN)
1785 dataen = NFCADDR_CMD_DATAEN;
1786 break;
1787 default:
1788 break;
1791 if (do_addr)
1792 acycle = nfc_make_addr(mtd, command, column, page_addr,
1793 &addr1234, &cycle0);
1795 nfc_addr_cmd = cmd1 | cmd2 | vcmd2 | acycle | csid | dataen | nfcwr;
1796 nfc_send_command(host, nfc_addr_cmd, addr1234, cycle0);
1798 if (dataen == NFCADDR_CMD_DATAEN)
1799 if (nfc_wait_interrupt(host, NFC_SR_XFR_DONE))
1800 dev_err(host->dev, "something wrong, No XFR_DONE interrupt comes.\n");
1803 * Program and erase have their own busy handlers status, sequential
1804 * in, and deplete1 need no delay.
1806 switch (command) {
1807 case NAND_CMD_CACHEDPROG:
1808 case NAND_CMD_PAGEPROG:
1809 case NAND_CMD_ERASE1:
1810 case NAND_CMD_ERASE2:
1811 case NAND_CMD_RNDIN:
1812 case NAND_CMD_STATUS:
1813 case NAND_CMD_RNDOUT:
1814 case NAND_CMD_SEQIN:
1815 case NAND_CMD_READID:
1816 return;
1818 case NAND_CMD_READ0:
1819 if (dataen == NFCADDR_CMD_DATAEN) {
1820 host->nfc->data_in_sram = host->nfc->sram_bank0 +
1821 nfc_get_sram_off(host);
1822 return;
1824 /* fall through */
1825 default:
1826 nfc_wait_interrupt(host, NFC_SR_RB_EDGE);
1830 static int nfc_sram_write_page(struct mtd_info *mtd, struct nand_chip *chip,
1831 uint32_t offset, int data_len, const uint8_t *buf,
1832 int oob_required, int page, int cached, int raw)
1834 int cfg, len;
1835 int status = 0;
1836 struct atmel_nand_host *host = chip->priv;
1837 void __iomem *sram = host->nfc->sram_bank0 + nfc_get_sram_off(host);
1839 /* Subpage write is not supported */
1840 if (offset || (data_len < mtd->writesize))
1841 return -EINVAL;
1843 cfg = nfc_readl(host->nfc->hsmc_regs, CFG);
1844 len = mtd->writesize;
1846 if (unlikely(raw)) {
1847 len += mtd->oobsize;
1848 nfc_writel(host->nfc->hsmc_regs, CFG, cfg | NFC_CFG_WSPARE);
1849 } else
1850 nfc_writel(host->nfc->hsmc_regs, CFG, cfg & ~NFC_CFG_WSPARE);
1852 /* Copy page data to sram that will write to nand via NFC */
1853 if (use_dma) {
1854 if (atmel_nand_dma_op(mtd, (void *)buf, len, 0) != 0)
1855 /* Fall back to use cpu copy */
1856 memcpy32_toio(sram, buf, len);
1857 } else {
1858 memcpy32_toio(sram, buf, len);
1861 if (chip->ecc.mode == NAND_ECC_HW && host->has_pmecc)
1863 * When use NFC sram, need set up PMECC before send
1864 * NAND_CMD_SEQIN command. Since when the nand command
1865 * is sent, nfc will do transfer from sram and nand.
1867 pmecc_enable(host, NAND_ECC_WRITE);
1869 host->nfc->will_write_sram = true;
1870 chip->cmdfunc(mtd, NAND_CMD_SEQIN, 0x00, page);
1871 host->nfc->will_write_sram = false;
1873 if (likely(!raw))
1874 /* Need to write ecc into oob */
1875 status = chip->ecc.write_page(mtd, chip, buf, oob_required);
1877 if (status < 0)
1878 return status;
1880 chip->cmdfunc(mtd, NAND_CMD_PAGEPROG, -1, -1);
1881 status = chip->waitfunc(mtd, chip);
1883 if ((status & NAND_STATUS_FAIL) && (chip->errstat))
1884 status = chip->errstat(mtd, chip, FL_WRITING, status, page);
1886 if (status & NAND_STATUS_FAIL)
1887 return -EIO;
1889 return 0;
1892 static int nfc_sram_init(struct mtd_info *mtd)
1894 struct nand_chip *chip = mtd->priv;
1895 struct atmel_nand_host *host = chip->priv;
1896 int res = 0;
1898 /* Initialize the NFC CFG register */
1899 unsigned int cfg_nfc = 0;
1901 /* set page size and oob layout */
1902 switch (mtd->writesize) {
1903 case 512:
1904 cfg_nfc = NFC_CFG_PAGESIZE_512;
1905 break;
1906 case 1024:
1907 cfg_nfc = NFC_CFG_PAGESIZE_1024;
1908 break;
1909 case 2048:
1910 cfg_nfc = NFC_CFG_PAGESIZE_2048;
1911 break;
1912 case 4096:
1913 cfg_nfc = NFC_CFG_PAGESIZE_4096;
1914 break;
1915 case 8192:
1916 cfg_nfc = NFC_CFG_PAGESIZE_8192;
1917 break;
1918 default:
1919 dev_err(host->dev, "Unsupported page size for NFC.\n");
1920 res = -ENXIO;
1921 return res;
1924 /* oob bytes size = (NFCSPARESIZE + 1) * 4
1925 * Max support spare size is 512 bytes. */
1926 cfg_nfc |= (((mtd->oobsize / 4) - 1) << NFC_CFG_NFC_SPARESIZE_BIT_POS
1927 & NFC_CFG_NFC_SPARESIZE);
1928 /* default set a max timeout */
1929 cfg_nfc |= NFC_CFG_RSPARE |
1930 NFC_CFG_NFC_DTOCYC | NFC_CFG_NFC_DTOMUL;
1932 nfc_writel(host->nfc->hsmc_regs, CFG, cfg_nfc);
1934 host->nfc->will_write_sram = false;
1935 nfc_set_sram_bank(host, 0);
1937 /* Use Write page with NFC SRAM only for PMECC or ECC NONE. */
1938 if (host->nfc->write_by_sram) {
1939 if ((chip->ecc.mode == NAND_ECC_HW && host->has_pmecc) ||
1940 chip->ecc.mode == NAND_ECC_NONE)
1941 chip->write_page = nfc_sram_write_page;
1942 else
1943 host->nfc->write_by_sram = false;
1946 dev_info(host->dev, "Using NFC Sram read %s\n",
1947 host->nfc->write_by_sram ? "and write" : "");
1948 return 0;
1951 static struct platform_driver atmel_nand_nfc_driver;
1953 * Probe for the NAND device.
1955 static int atmel_nand_probe(struct platform_device *pdev)
1957 struct atmel_nand_host *host;
1958 struct mtd_info *mtd;
1959 struct nand_chip *nand_chip;
1960 struct resource *mem;
1961 struct mtd_part_parser_data ppdata = {};
1962 int res, irq;
1964 /* Allocate memory for the device structure (and zero it) */
1965 host = devm_kzalloc(&pdev->dev, sizeof(*host), GFP_KERNEL);
1966 if (!host)
1967 return -ENOMEM;
1969 res = platform_driver_register(&atmel_nand_nfc_driver);
1970 if (res)
1971 dev_err(&pdev->dev, "atmel_nand: can't register NFC driver\n");
1973 mem = platform_get_resource(pdev, IORESOURCE_MEM, 0);
1974 host->io_base = devm_ioremap_resource(&pdev->dev, mem);
1975 if (IS_ERR(host->io_base)) {
1976 dev_err(&pdev->dev, "atmel_nand: ioremap resource failed\n");
1977 res = PTR_ERR(host->io_base);
1978 goto err_nand_ioremap;
1980 host->io_phys = (dma_addr_t)mem->start;
1982 mtd = &host->mtd;
1983 nand_chip = &host->nand_chip;
1984 host->dev = &pdev->dev;
1985 if (IS_ENABLED(CONFIG_OF) && pdev->dev.of_node) {
1986 /* Only when CONFIG_OF is enabled of_node can be parsed */
1987 res = atmel_of_init_port(host, pdev->dev.of_node);
1988 if (res)
1989 goto err_nand_ioremap;
1990 } else {
1991 memcpy(&host->board, dev_get_platdata(&pdev->dev),
1992 sizeof(struct atmel_nand_data));
1995 nand_chip->priv = host; /* link the private data structures */
1996 mtd->priv = nand_chip;
1997 mtd->owner = THIS_MODULE;
1999 /* Set address of NAND IO lines */
2000 nand_chip->IO_ADDR_R = host->io_base;
2001 nand_chip->IO_ADDR_W = host->io_base;
2003 if (nand_nfc.is_initialized) {
2004 /* NFC driver is probed and initialized */
2005 host->nfc = &nand_nfc;
2007 nand_chip->select_chip = nfc_select_chip;
2008 nand_chip->dev_ready = nfc_device_ready;
2009 nand_chip->cmdfunc = nfc_nand_command;
2011 /* Initialize the interrupt for NFC */
2012 irq = platform_get_irq(pdev, 0);
2013 if (irq < 0) {
2014 dev_err(host->dev, "Cannot get HSMC irq!\n");
2015 res = irq;
2016 goto err_nand_ioremap;
2019 res = devm_request_irq(&pdev->dev, irq, hsmc_interrupt,
2020 0, "hsmc", host);
2021 if (res) {
2022 dev_err(&pdev->dev, "Unable to request HSMC irq %d\n",
2023 irq);
2024 goto err_nand_ioremap;
2026 } else {
2027 res = atmel_nand_set_enable_ready_pins(mtd);
2028 if (res)
2029 goto err_nand_ioremap;
2031 nand_chip->cmd_ctrl = atmel_nand_cmd_ctrl;
2034 nand_chip->ecc.mode = host->board.ecc_mode;
2035 nand_chip->chip_delay = 20; /* 20us command delay time */
2037 if (host->board.bus_width_16) /* 16-bit bus width */
2038 nand_chip->options |= NAND_BUSWIDTH_16;
2040 nand_chip->read_buf = atmel_read_buf;
2041 nand_chip->write_buf = atmel_write_buf;
2043 platform_set_drvdata(pdev, host);
2044 atmel_nand_enable(host);
2046 if (gpio_is_valid(host->board.det_pin)) {
2047 res = devm_gpio_request(&pdev->dev,
2048 host->board.det_pin, "nand_det");
2049 if (res < 0) {
2050 dev_err(&pdev->dev,
2051 "can't request det gpio %d\n",
2052 host->board.det_pin);
2053 goto err_no_card;
2056 res = gpio_direction_input(host->board.det_pin);
2057 if (res < 0) {
2058 dev_err(&pdev->dev,
2059 "can't request input direction det gpio %d\n",
2060 host->board.det_pin);
2061 goto err_no_card;
2064 if (gpio_get_value(host->board.det_pin)) {
2065 dev_info(&pdev->dev, "No SmartMedia card inserted.\n");
2066 res = -ENXIO;
2067 goto err_no_card;
2071 if (host->board.on_flash_bbt || on_flash_bbt) {
2072 dev_info(&pdev->dev, "Use On Flash BBT\n");
2073 nand_chip->bbt_options |= NAND_BBT_USE_FLASH;
2076 if (!host->board.has_dma)
2077 use_dma = 0;
2079 if (use_dma) {
2080 dma_cap_mask_t mask;
2082 dma_cap_zero(mask);
2083 dma_cap_set(DMA_MEMCPY, mask);
2084 host->dma_chan = dma_request_channel(mask, NULL, NULL);
2085 if (!host->dma_chan) {
2086 dev_err(host->dev, "Failed to request DMA channel\n");
2087 use_dma = 0;
2090 if (use_dma)
2091 dev_info(host->dev, "Using %s for DMA transfers.\n",
2092 dma_chan_name(host->dma_chan));
2093 else
2094 dev_info(host->dev, "No DMA support for NAND access.\n");
2096 /* first scan to find the device and get the page size */
2097 if (nand_scan_ident(mtd, 1, NULL)) {
2098 res = -ENXIO;
2099 goto err_scan_ident;
2102 if (nand_chip->ecc.mode == NAND_ECC_HW) {
2103 if (host->has_pmecc)
2104 res = atmel_pmecc_nand_init_params(pdev, host);
2105 else
2106 res = atmel_hw_nand_init_params(pdev, host);
2108 if (res != 0)
2109 goto err_hw_ecc;
2112 /* initialize the nfc configuration register */
2113 if (host->nfc && host->nfc->use_nfc_sram) {
2114 res = nfc_sram_init(mtd);
2115 if (res) {
2116 host->nfc->use_nfc_sram = false;
2117 dev_err(host->dev, "Disable use nfc sram for data transfer.\n");
2121 /* second phase scan */
2122 if (nand_scan_tail(mtd)) {
2123 res = -ENXIO;
2124 goto err_scan_tail;
2127 mtd->name = "atmel_nand";
2128 ppdata.of_node = pdev->dev.of_node;
2129 res = mtd_device_parse_register(mtd, NULL, &ppdata,
2130 host->board.parts, host->board.num_parts);
2131 if (!res)
2132 return res;
2134 err_scan_tail:
2135 if (host->has_pmecc && host->nand_chip.ecc.mode == NAND_ECC_HW)
2136 pmecc_writel(host->ecc, CTRL, PMECC_CTRL_DISABLE);
2137 err_hw_ecc:
2138 err_scan_ident:
2139 err_no_card:
2140 atmel_nand_disable(host);
2141 if (host->dma_chan)
2142 dma_release_channel(host->dma_chan);
2143 err_nand_ioremap:
2144 return res;
2148 * Remove a NAND device.
2150 static int atmel_nand_remove(struct platform_device *pdev)
2152 struct atmel_nand_host *host = platform_get_drvdata(pdev);
2153 struct mtd_info *mtd = &host->mtd;
2155 nand_release(mtd);
2157 atmel_nand_disable(host);
2159 if (host->has_pmecc && host->nand_chip.ecc.mode == NAND_ECC_HW) {
2160 pmecc_writel(host->ecc, CTRL, PMECC_CTRL_DISABLE);
2161 pmerrloc_writel(host->pmerrloc_base, ELDIS,
2162 PMERRLOC_DISABLE);
2165 if (host->dma_chan)
2166 dma_release_channel(host->dma_chan);
2168 platform_driver_unregister(&atmel_nand_nfc_driver);
2170 return 0;
2173 static const struct of_device_id atmel_nand_dt_ids[] = {
2174 { .compatible = "atmel,at91rm9200-nand" },
2175 { /* sentinel */ }
2178 MODULE_DEVICE_TABLE(of, atmel_nand_dt_ids);
2180 static int atmel_nand_nfc_probe(struct platform_device *pdev)
2182 struct atmel_nfc *nfc = &nand_nfc;
2183 struct resource *nfc_cmd_regs, *nfc_hsmc_regs, *nfc_sram;
2185 nfc_cmd_regs = platform_get_resource(pdev, IORESOURCE_MEM, 0);
2186 nfc->base_cmd_regs = devm_ioremap_resource(&pdev->dev, nfc_cmd_regs);
2187 if (IS_ERR(nfc->base_cmd_regs))
2188 return PTR_ERR(nfc->base_cmd_regs);
2190 nfc_hsmc_regs = platform_get_resource(pdev, IORESOURCE_MEM, 1);
2191 nfc->hsmc_regs = devm_ioremap_resource(&pdev->dev, nfc_hsmc_regs);
2192 if (IS_ERR(nfc->hsmc_regs))
2193 return PTR_ERR(nfc->hsmc_regs);
2195 nfc_sram = platform_get_resource(pdev, IORESOURCE_MEM, 2);
2196 if (nfc_sram) {
2197 nfc->sram_bank0 = devm_ioremap_resource(&pdev->dev, nfc_sram);
2198 if (IS_ERR(nfc->sram_bank0)) {
2199 dev_warn(&pdev->dev, "Fail to ioremap the NFC sram with error: %ld. So disable NFC sram.\n",
2200 PTR_ERR(nfc->sram_bank0));
2201 } else {
2202 nfc->use_nfc_sram = true;
2203 nfc->sram_bank0_phys = (dma_addr_t)nfc_sram->start;
2205 if (pdev->dev.of_node)
2206 nfc->write_by_sram = of_property_read_bool(
2207 pdev->dev.of_node,
2208 "atmel,write-by-sram");
2212 nfc->is_initialized = true;
2213 dev_info(&pdev->dev, "NFC is probed.\n");
2214 return 0;
2217 static const struct of_device_id atmel_nand_nfc_match[] = {
2218 { .compatible = "atmel,sama5d3-nfc" },
2219 { /* sentinel */ }
2221 MODULE_DEVICE_TABLE(of, atmel_nand_nfc_match);
2223 static struct platform_driver atmel_nand_nfc_driver = {
2224 .driver = {
2225 .name = "atmel_nand_nfc",
2226 .owner = THIS_MODULE,
2227 .of_match_table = of_match_ptr(atmel_nand_nfc_match),
2229 .probe = atmel_nand_nfc_probe,
2232 static struct platform_driver atmel_nand_driver = {
2233 .probe = atmel_nand_probe,
2234 .remove = atmel_nand_remove,
2235 .driver = {
2236 .name = "atmel_nand",
2237 .owner = THIS_MODULE,
2238 .of_match_table = of_match_ptr(atmel_nand_dt_ids),
2242 module_platform_driver(atmel_nand_driver);
2244 MODULE_LICENSE("GPL");
2245 MODULE_AUTHOR("Rick Bronson");
2246 MODULE_DESCRIPTION("NAND/SmartMedia driver for AT91 / AVR32");
2247 MODULE_ALIAS("platform:atmel_nand");