?  search:
summary | log | graphiclog1 | graphiclog2 | commit | commitdiff | tree | refs | edit | fork
blame | history | raw | HEAD
Merge 4.11-rc4 into tty-next
[linux/fpc-iii.git] / drivers / usb / musb / blackfin.c
blob4418574a36a1d8c08f4f001778f4f0e4262b7cb7
1 /*
2 * MUSB OTG controller driver for Blackfin Processors
3 *
4 * Copyright 2006-2008 Analog Devices Inc.
5 *
6 * Enter bugs at http://blackfin.uclinux.org/
7 *
8 * Licensed under the GPL-2 or later.
9 */
10
11 #include <linux/module.h>
12 #include <linux/kernel.h>
13 #include <linux/sched.h>
14 #include <linux/list.h>
15 #include <linux/gpio.h>
16 #include <linux/io.h>
17 #include <linux/err.h>
18 #include <linux/platform_device.h>
19 #include <linux/dma-mapping.h>
20 #include <linux/prefetch.h>
21 #include <linux/usb/usb_phy_generic.h>
22
23 #include <asm/cacheflush.h>
24
25 #include "musb_core.h"
26 #include "musbhsdma.h"
27 #include "blackfin.h"
28
29 struct bfin_glue {
30 struct device *dev;
31 struct platform_device *musb;
32 struct platform_device *phy;
33 };
34 #define glue_to_musb(g) platform_get_drvdata(g->musb)
35
36 static u32 bfin_fifo_offset(u8 epnum)
37 {
38 return USB_OFFSET(USB_EP0_FIFO) + (epnum * 8);
39 }
40
41 static u8 bfin_readb(const void __iomem *addr, unsigned offset)
42 {
43 return (u8)(bfin_read16(addr + offset));
44 }
45
46 static u16 bfin_readw(const void __iomem *addr, unsigned offset)
47 {
48 return bfin_read16(addr + offset);
49 }
50
51 static u32 bfin_readl(const void __iomem *addr, unsigned offset)
52 {
53 return (u32)(bfin_read16(addr + offset));
54 }
55
56 static void bfin_writeb(void __iomem *addr, unsigned offset, u8 data)
57 {
58 bfin_write16(addr + offset, (u16)data);
59 }
60
61 static void bfin_writew(void __iomem *addr, unsigned offset, u16 data)
62 {
63 bfin_write16(addr + offset, data);
64 }
65
66 static void bfin_writel(void __iomem *addr, unsigned offset, u32 data)
67 {
68 bfin_write16(addr + offset, (u16)data);
69 }
70
71 /*
72 * Load an endpoint's FIFO
73 */
74 static void bfin_write_fifo(struct musb_hw_ep *hw_ep, u16 len, const u8 *src)
75 {
76 struct musb *musb = hw_ep->musb;
77 void __iomem *fifo = hw_ep->fifo;
78 void __iomem *epio = hw_ep->regs;
79 u8 epnum = hw_ep->epnum;
80
81 prefetch((u8 *)src);
82
83 musb_writew(epio, MUSB_TXCOUNT, len);
84
85 dev_dbg(musb->controller, "TX ep%d fifo %p count %d buf %p, epio %p\n",
86 hw_ep->epnum, fifo, len, src, epio);
87
88 dump_fifo_data(src, len);
89
90 if (!ANOMALY_05000380 && epnum != 0) {
91 u16 dma_reg;
92
93 flush_dcache_range((unsigned long)src,
94 (unsigned long)(src + len));
95
96 /* Setup DMA address register */
97 dma_reg = (u32)src;
98 bfin_write16(USB_DMA_REG(epnum, USB_DMAx_ADDR_LOW), dma_reg);
99 SSYNC();
100
101 dma_reg = (u32)src >> 16;
102 bfin_write16(USB_DMA_REG(epnum, USB_DMAx_ADDR_HIGH), dma_reg);
103 SSYNC();
104
105 /* Setup DMA count register */
106 bfin_write16(USB_DMA_REG(epnum, USB_DMAx_COUNT_LOW), len);
107 bfin_write16(USB_DMA_REG(epnum, USB_DMAx_COUNT_HIGH), 0);
108 SSYNC();
109
110 /* Enable the DMA */
111 dma_reg = (epnum << 4) | DMA_ENA | INT_ENA | DIRECTION;
112 bfin_write16(USB_DMA_REG(epnum, USB_DMAx_CTRL), dma_reg);
113 SSYNC();
114
115 /* Wait for complete */
116 while (!(bfin_read_USB_DMA_INTERRUPT() & (1 << epnum)))
117 cpu_relax();
118
119 /* acknowledge dma interrupt */
120 bfin_write_USB_DMA_INTERRUPT(1 << epnum);
121 SSYNC();
122
123 /* Reset DMA */
124 bfin_write16(USB_DMA_REG(epnum, USB_DMAx_CTRL), 0);
125 SSYNC();
126 } else {
127 SSYNC();
128
129 if (unlikely((unsigned long)src & 0x01))
130 outsw_8((unsigned long)fifo, src, (len + 1) >> 1);
131 else
132 outsw((unsigned long)fifo, src, (len + 1) >> 1);
133 }
134 }
135 /*
136 * Unload an endpoint's FIFO
137 */
138 static void bfin_read_fifo(struct musb_hw_ep *hw_ep, u16 len, u8 *dst)
139 {
140 struct musb *musb = hw_ep->musb;
141 void __iomem *fifo = hw_ep->fifo;
142 u8 epnum = hw_ep->epnum;
143
144 if (ANOMALY_05000467 && epnum != 0) {
145 u16 dma_reg;
146
147 invalidate_dcache_range((unsigned long)dst,
148 (unsigned long)(dst + len));
149
150 /* Setup DMA address register */
151 dma_reg = (u32)dst;
152 bfin_write16(USB_DMA_REG(epnum, USB_DMAx_ADDR_LOW), dma_reg);
153 SSYNC();
154
155 dma_reg = (u32)dst >> 16;
156 bfin_write16(USB_DMA_REG(epnum, USB_DMAx_ADDR_HIGH), dma_reg);
157 SSYNC();
158
159 /* Setup DMA count register */
160 bfin_write16(USB_DMA_REG(epnum, USB_DMAx_COUNT_LOW), len);
161 bfin_write16(USB_DMA_REG(epnum, USB_DMAx_COUNT_HIGH), 0);
162 SSYNC();
163
164 /* Enable the DMA */
165 dma_reg = (epnum << 4) | DMA_ENA | INT_ENA;
166 bfin_write16(USB_DMA_REG(epnum, USB_DMAx_CTRL), dma_reg);
167 SSYNC();
168
169 /* Wait for complete */
170 while (!(bfin_read_USB_DMA_INTERRUPT() & (1 << epnum)))
171 cpu_relax();
172
173 /* acknowledge dma interrupt */
174 bfin_write_USB_DMA_INTERRUPT(1 << epnum);
175 SSYNC();
176
177 /* Reset DMA */
178 bfin_write16(USB_DMA_REG(epnum, USB_DMAx_CTRL), 0);
179 SSYNC();
180 } else {
181 SSYNC();
182 /* Read the last byte of packet with odd size from address fifo + 4
183 * to trigger 1 byte access to EP0 FIFO.
184 */
185 if (len == 1)
186 *dst = (u8)inw((unsigned long)fifo + 4);
187 else {
188 if (unlikely((unsigned long)dst & 0x01))
189 insw_8((unsigned long)fifo, dst, len >> 1);
190 else
191 insw((unsigned long)fifo, dst, len >> 1);
192
193 if (len & 0x01)
194 *(dst + len - 1) = (u8)inw((unsigned long)fifo + 4);
195 }
196 }
197 dev_dbg(musb->controller, "%cX ep%d fifo %p count %d buf %p\n",
198 'R', hw_ep->epnum, fifo, len, dst);
199
200 dump_fifo_data(dst, len);
201 }
202
203 static irqreturn_t blackfin_interrupt(int irq, void *__hci)
204 {
205 unsigned long flags;
206 irqreturn_t retval = IRQ_NONE;
207 struct musb *musb = __hci;
208
209 spin_lock_irqsave(&musb->lock, flags);
210
211 musb->int_usb = musb_readb(musb->mregs, MUSB_INTRUSB);
212 musb->int_tx = musb_readw(musb->mregs, MUSB_INTRTX);
213 musb->int_rx = musb_readw(musb->mregs, MUSB_INTRRX);
214
215 if (musb->int_usb || musb->int_tx || musb->int_rx) {
216 musb_writeb(musb->mregs, MUSB_INTRUSB, musb->int_usb);
217 musb_writew(musb->mregs, MUSB_INTRTX, musb->int_tx);
218 musb_writew(musb->mregs, MUSB_INTRRX, musb->int_rx);
219 retval = musb_interrupt(musb);
220 }
221
222 /* Start sampling ID pin, when plug is removed from MUSB */
223 if ((musb->xceiv->otg->state == OTG_STATE_B_IDLE
224 || musb->xceiv->otg->state == OTG_STATE_A_WAIT_BCON) ||
225 (musb->int_usb & MUSB_INTR_DISCONNECT && is_host_active(musb))) {
226 mod_timer(&musb_conn_timer, jiffies + TIMER_DELAY);
227 musb->a_wait_bcon = TIMER_DELAY;
228 }
229
230 spin_unlock_irqrestore(&musb->lock, flags);
231
232 return retval;
233 }
234
235 static void musb_conn_timer_handler(unsigned long _musb)
236 {
237 struct musb *musb = (void *)_musb;
238 unsigned long flags;
239 u16 val;
240 static u8 toggle;
241
242 spin_lock_irqsave(&musb->lock, flags);
243 switch (musb->xceiv->otg->state) {
244 case OTG_STATE_A_IDLE:
245 case OTG_STATE_A_WAIT_BCON:
246 /* Start a new session */
247 val = musb_readw(musb->mregs, MUSB_DEVCTL);
248 val &= ~MUSB_DEVCTL_SESSION;
249 musb_writew(musb->mregs, MUSB_DEVCTL, val);
250 val |= MUSB_DEVCTL_SESSION;
251 musb_writew(musb->mregs, MUSB_DEVCTL, val);
252 /* Check if musb is host or peripheral. */
253 val = musb_readw(musb->mregs, MUSB_DEVCTL);
254
255 if (!(val & MUSB_DEVCTL_BDEVICE)) {
256 gpio_set_value(musb->config->gpio_vrsel, 1);
257 musb->xceiv->otg->state = OTG_STATE_A_WAIT_BCON;
258 } else {
259 gpio_set_value(musb->config->gpio_vrsel, 0);
260 /* Ignore VBUSERROR and SUSPEND IRQ */
261 val = musb_readb(musb->mregs, MUSB_INTRUSBE);
262 val &= ~MUSB_INTR_VBUSERROR;
263 musb_writeb(musb->mregs, MUSB_INTRUSBE, val);
264
265 val = MUSB_INTR_SUSPEND | MUSB_INTR_VBUSERROR;
266 musb_writeb(musb->mregs, MUSB_INTRUSB, val);
267 musb->xceiv->otg->state = OTG_STATE_B_IDLE;
268 }
269 mod_timer(&musb_conn_timer, jiffies + TIMER_DELAY);
270 break;
271 case OTG_STATE_B_IDLE:
272 /*
273 * Start a new session. It seems that MUSB needs taking
274 * some time to recognize the type of the plug inserted?
275 */
276 val = musb_readw(musb->mregs, MUSB_DEVCTL);
277 val |= MUSB_DEVCTL_SESSION;
278 musb_writew(musb->mregs, MUSB_DEVCTL, val);
279 val = musb_readw(musb->mregs, MUSB_DEVCTL);
280
281 if (!(val & MUSB_DEVCTL_BDEVICE)) {
282 gpio_set_value(musb->config->gpio_vrsel, 1);
283 musb->xceiv->otg->state = OTG_STATE_A_WAIT_BCON;
284 } else {
285 gpio_set_value(musb->config->gpio_vrsel, 0);
286
287 /* Ignore VBUSERROR and SUSPEND IRQ */
288 val = musb_readb(musb->mregs, MUSB_INTRUSBE);
289 val &= ~MUSB_INTR_VBUSERROR;
290 musb_writeb(musb->mregs, MUSB_INTRUSBE, val);
291
292 val = MUSB_INTR_SUSPEND | MUSB_INTR_VBUSERROR;
293 musb_writeb(musb->mregs, MUSB_INTRUSB, val);
294
295 /* Toggle the Soft Conn bit, so that we can response to
296 * the inserting of either A-plug or B-plug.
297 */
298 if (toggle) {
299 val = musb_readb(musb->mregs, MUSB_POWER);
300 val &= ~MUSB_POWER_SOFTCONN;
301 musb_writeb(musb->mregs, MUSB_POWER, val);
302 toggle = 0;
303 } else {
304 val = musb_readb(musb->mregs, MUSB_POWER);
305 val |= MUSB_POWER_SOFTCONN;
306 musb_writeb(musb->mregs, MUSB_POWER, val);
307 toggle = 1;
308 }
309 /* The delay time is set to 1/4 second by default,
310 * shortening it, if accelerating A-plug detection
311 * is needed in OTG mode.
312 */
313 mod_timer(&musb_conn_timer, jiffies + TIMER_DELAY / 4);
314 }
315 break;
316 default:
317 dev_dbg(musb->controller, "%s state not handled\n",
318 usb_otg_state_string(musb->xceiv->otg->state));
319 break;
320 }
321 spin_unlock_irqrestore(&musb->lock, flags);
322
323 dev_dbg(musb->controller, "state is %s\n",
324 usb_otg_state_string(musb->xceiv->otg->state));
325 }
326
327 static void bfin_musb_enable(struct musb *musb)
328 {
329 /* REVISIT is this really correct ? */
330 }
331
332 static void bfin_musb_disable(struct musb *musb)
333 {
334 }
335
336 static void bfin_musb_set_vbus(struct musb *musb, int is_on)
337 {
338 int value = musb->config->gpio_vrsel_active;
339 if (!is_on)
340 value = !value;
341 gpio_set_value(musb->config->gpio_vrsel, value);
342
343 dev_dbg(musb->controller, "VBUS %s, devctl %02x "
344 /* otg %3x conf %08x prcm %08x */ "\n",
345 usb_otg_state_string(musb->xceiv->otg->state),
346 musb_readb(musb->mregs, MUSB_DEVCTL));
347 }
348
349 static int bfin_musb_set_power(struct usb_phy *x, unsigned mA)
350 {
351 return 0;
352 }
353
354 static int bfin_musb_vbus_status(struct musb *musb)
355 {
356 return 0;
357 }
358
359 static int bfin_musb_set_mode(struct musb *musb, u8 musb_mode)
360 {
361 return -EIO;
362 }
363
364 static int bfin_musb_adjust_channel_params(struct dma_channel *channel,
365 u16 packet_sz, u8 *mode,
366 dma_addr_t *dma_addr, u32 *len)
367 {
368 struct musb_dma_channel *musb_channel = channel->private_data;
369
370 /*
371 * Anomaly 05000450 might cause data corruption when using DMA
372 * MODE 1 transmits with short packet. So to work around this,
373 * we truncate all MODE 1 transfers down to a multiple of the
374 * max packet size, and then do the last short packet transfer
375 * (if there is any) using MODE 0.
376 */
377 if (ANOMALY_05000450) {
378 if (musb_channel->transmit && *mode == 1)
379 *len = *len - (*len % packet_sz);
380 }
381
382 return 0;
383 }
384
385 static void bfin_musb_reg_init(struct musb *musb)
386 {
387 if (ANOMALY_05000346) {
388 bfin_write_USB_APHY_CALIB(ANOMALY_05000346_value);
389 SSYNC();
390 }
391
392 if (ANOMALY_05000347) {
393 bfin_write_USB_APHY_CNTRL(0x0);
394 SSYNC();
395 }
396
397 /* Configure PLL oscillator register */
398 bfin_write_USB_PLLOSC_CTRL(0x3080 |
399 ((480/musb->config->clkin) << 1));
400 SSYNC();
401
402 bfin_write_USB_SRP_CLKDIV((get_sclk()/1000) / 32 - 1);
403 SSYNC();
404
405 bfin_write_USB_EP_NI0_RXMAXP(64);
406 SSYNC();
407
408 bfin_write_USB_EP_NI0_TXMAXP(64);
409 SSYNC();
410
411 /* Route INTRUSB/INTR_RX/INTR_TX to USB_INT0*/
412 bfin_write_USB_GLOBINTR(0x7);
413 SSYNC();
414
415 bfin_write_USB_GLOBAL_CTL(GLOBAL_ENA | EP1_TX_ENA | EP2_TX_ENA |
416 EP3_TX_ENA | EP4_TX_ENA | EP5_TX_ENA |
417 EP6_TX_ENA | EP7_TX_ENA | EP1_RX_ENA |
418 EP2_RX_ENA | EP3_RX_ENA | EP4_RX_ENA |
419 EP5_RX_ENA | EP6_RX_ENA | EP7_RX_ENA);
420 SSYNC();
421 }
422
423 static int bfin_musb_init(struct musb *musb)
424 {
425
426 /*
427 * Rev 1.0 BF549 EZ-KITs require PE7 to be high for both DEVICE
428 * and OTG HOST modes, while rev 1.1 and greater require PE7 to
429 * be low for DEVICE mode and high for HOST mode. We set it high
430 * here because we are in host mode
431 */
432
433 if (gpio_request(musb->config->gpio_vrsel, "USB_VRSEL")) {
434 printk(KERN_ERR "Failed ro request USB_VRSEL GPIO_%d\n",
435 musb->config->gpio_vrsel);
436 return -ENODEV;
437 }
438 gpio_direction_output(musb->config->gpio_vrsel, 0);
439
440 musb->xceiv = usb_get_phy(USB_PHY_TYPE_USB2);
441 if (IS_ERR_OR_NULL(musb->xceiv)) {
442 gpio_free(musb->config->gpio_vrsel);
443 return -EPROBE_DEFER;
444 }
445
446 bfin_musb_reg_init(musb);
447
448 setup_timer(&musb_conn_timer, musb_conn_timer_handler,
449 (unsigned long) musb);
450
451 musb->xceiv->set_power = bfin_musb_set_power;
452
453 musb->isr = blackfin_interrupt;
454 musb->double_buffer_not_ok = true;
455
456 return 0;
457 }
458
459 static int bfin_musb_exit(struct musb *musb)
460 {
461 gpio_free(musb->config->gpio_vrsel);
462 usb_put_phy(musb->xceiv);
463
464 return 0;
465 }
466
467 static const struct musb_platform_ops bfin_ops = {
468 .quirks = MUSB_DMA_INVENTRA,
469 .init = bfin_musb_init,
470 .exit = bfin_musb_exit,
471
472 .fifo_offset = bfin_fifo_offset,
473 .readb = bfin_readb,
474 .writeb = bfin_writeb,
475 .readw = bfin_readw,
476 .writew = bfin_writew,
477 .readl = bfin_readl,
478 .writel = bfin_writel,
479 .fifo_mode = 2,
480 .read_fifo = bfin_read_fifo,
481 .write_fifo = bfin_write_fifo,
482 #ifdef CONFIG_USB_INVENTRA_DMA
483 .dma_init = musbhs_dma_controller_create,
484 .dma_exit = musbhs_dma_controller_destroy,
485 #endif
486 .enable = bfin_musb_enable,
487 .disable = bfin_musb_disable,
488
489 .set_mode = bfin_musb_set_mode,
490
491 .vbus_status = bfin_musb_vbus_status,
492 .set_vbus = bfin_musb_set_vbus,
493
494 .adjust_channel_params = bfin_musb_adjust_channel_params,
495 };
496
497 static u64 bfin_dmamask = DMA_BIT_MASK(32);
498
499 static int bfin_probe(struct platform_device *pdev)
500 {
501 struct resource musb_resources[2];
502 struct musb_hdrc_platform_data *pdata = dev_get_platdata(&pdev->dev);
503 struct platform_device *musb;
504 struct bfin_glue *glue;
505
506 int ret = -ENOMEM;
507
508 glue = devm_kzalloc(&pdev->dev, sizeof(*glue), GFP_KERNEL);
509 if (!glue)
510 goto err0;
511
512 musb = platform_device_alloc("musb-hdrc", PLATFORM_DEVID_AUTO);
513 if (!musb)
514 goto err0;
515
516 musb->dev.parent = &pdev->dev;
517 musb->dev.dma_mask = &bfin_dmamask;
518 musb->dev.coherent_dma_mask = bfin_dmamask;
519
520 glue->dev = &pdev->dev;
521 glue->musb = musb;
522
523 pdata->platform_ops = &bfin_ops;
524
525 glue->phy = usb_phy_generic_register();
526 if (IS_ERR(glue->phy))
527 goto err1;
528 platform_set_drvdata(pdev, glue);
529
530 memset(musb_resources, 0x00, sizeof(*musb_resources) *
531 ARRAY_SIZE(musb_resources));
532
533 musb_resources[0].name = pdev->resource[0].name;
534 musb_resources[0].start = pdev->resource[0].start;
535 musb_resources[0].end = pdev->resource[0].end;
536 musb_resources[0].flags = pdev->resource[0].flags;
537
538 musb_resources[1].name = pdev->resource[1].name;
539 musb_resources[1].start = pdev->resource[1].start;
540 musb_resources[1].end = pdev->resource[1].end;
541 musb_resources[1].flags = pdev->resource[1].flags;
542
543 ret = platform_device_add_resources(musb, musb_resources,
544 ARRAY_SIZE(musb_resources));
545 if (ret) {
546 dev_err(&pdev->dev, "failed to add resources\n");
547 goto err2;
548 }
549
550 ret = platform_device_add_data(musb, pdata, sizeof(*pdata));
551 if (ret) {
552 dev_err(&pdev->dev, "failed to add platform_data\n");
553 goto err2;
554 }
555
556 ret = platform_device_add(musb);
557 if (ret) {
558 dev_err(&pdev->dev, "failed to register musb device\n");
559 goto err2;
560 }
561
562 return 0;
563
564 err2:
565 usb_phy_generic_unregister(glue->phy);
566
567 err1:
568 platform_device_put(musb);
569
570 err0:
571 return ret;
572 }
573
574 static int bfin_remove(struct platform_device *pdev)
575 {
576 struct bfin_glue *glue = platform_get_drvdata(pdev);
577
578 platform_device_unregister(glue->musb);
579 usb_phy_generic_unregister(glue->phy);
580
581 return 0;
582 }
583
584 static int __maybe_unused bfin_suspend(struct device *dev)
585 {
586 struct bfin_glue *glue = dev_get_drvdata(dev);
587 struct musb *musb = glue_to_musb(glue);
588
589 if (is_host_active(musb))
590 /*
591 * During hibernate gpio_vrsel will change from high to low
592 * low which will generate wakeup event resume the system
593 * immediately. Set it to 0 before hibernate to avoid this
594 * wakeup event.
595 */
596 gpio_set_value(musb->config->gpio_vrsel, 0);
597
598 return 0;
599 }
600
601 static int __maybe_unused bfin_resume(struct device *dev)
602 {
603 struct bfin_glue *glue = dev_get_drvdata(dev);
604 struct musb *musb = glue_to_musb(glue);
605
606 bfin_musb_reg_init(musb);
607
608 return 0;
609 }
610
611 static SIMPLE_DEV_PM_OPS(bfin_pm_ops, bfin_suspend, bfin_resume);
612
613 static struct platform_driver bfin_driver = {
614 .probe = bfin_probe,
615 .remove = bfin_remove,
616 .driver = {
617 .name = "musb-blackfin",
618 .pm = &bfin_pm_ops,
619 },
620 };
621
622 MODULE_DESCRIPTION("Blackfin MUSB Glue Layer");
623 MODULE_AUTHOR("Bryan Wy <cooloney@kernel.org>");
624 MODULE_LICENSE("GPL v2");
625 module_platform_driver(bfin_driver);
Linux with added FPC-III support