serial: exar: Fix GPIO configuration for Sealevel cards based on XR17V35X
[linux/fpc-iii.git] / mm / workingset.c
blob50b7937bab32fe6b16e2a53a2ddeada8d3710144
1 // SPDX-License-Identifier: GPL-2.0
2 /*
3 * Workingset detection
5 * Copyright (C) 2013 Red Hat, Inc., Johannes Weiner
6 */
8 #include <linux/memcontrol.h>
9 #include <linux/writeback.h>
10 #include <linux/shmem_fs.h>
11 #include <linux/pagemap.h>
12 #include <linux/atomic.h>
13 #include <linux/module.h>
14 #include <linux/swap.h>
15 #include <linux/dax.h>
16 #include <linux/fs.h>
17 #include <linux/mm.h>
20 * Double CLOCK lists
22 * Per node, two clock lists are maintained for file pages: the
23 * inactive and the active list. Freshly faulted pages start out at
24 * the head of the inactive list and page reclaim scans pages from the
25 * tail. Pages that are accessed multiple times on the inactive list
26 * are promoted to the active list, to protect them from reclaim,
27 * whereas active pages are demoted to the inactive list when the
28 * active list grows too big.
30 * fault ------------------------+
31 * |
32 * +--------------+ | +-------------+
33 * reclaim <- | inactive | <-+-- demotion | active | <--+
34 * +--------------+ +-------------+ |
35 * | |
36 * +-------------- promotion ------------------+
39 * Access frequency and refault distance
41 * A workload is thrashing when its pages are frequently used but they
42 * are evicted from the inactive list every time before another access
43 * would have promoted them to the active list.
45 * In cases where the average access distance between thrashing pages
46 * is bigger than the size of memory there is nothing that can be
47 * done - the thrashing set could never fit into memory under any
48 * circumstance.
50 * However, the average access distance could be bigger than the
51 * inactive list, yet smaller than the size of memory. In this case,
52 * the set could fit into memory if it weren't for the currently
53 * active pages - which may be used more, hopefully less frequently:
55 * +-memory available to cache-+
56 * | |
57 * +-inactive------+-active----+
58 * a b | c d e f g h i | J K L M N |
59 * +---------------+-----------+
61 * It is prohibitively expensive to accurately track access frequency
62 * of pages. But a reasonable approximation can be made to measure
63 * thrashing on the inactive list, after which refaulting pages can be
64 * activated optimistically to compete with the existing active pages.
66 * Approximating inactive page access frequency - Observations:
68 * 1. When a page is accessed for the first time, it is added to the
69 * head of the inactive list, slides every existing inactive page
70 * towards the tail by one slot, and pushes the current tail page
71 * out of memory.
73 * 2. When a page is accessed for the second time, it is promoted to
74 * the active list, shrinking the inactive list by one slot. This
75 * also slides all inactive pages that were faulted into the cache
76 * more recently than the activated page towards the tail of the
77 * inactive list.
79 * Thus:
81 * 1. The sum of evictions and activations between any two points in
82 * time indicate the minimum number of inactive pages accessed in
83 * between.
85 * 2. Moving one inactive page N page slots towards the tail of the
86 * list requires at least N inactive page accesses.
88 * Combining these:
90 * 1. When a page is finally evicted from memory, the number of
91 * inactive pages accessed while the page was in cache is at least
92 * the number of page slots on the inactive list.
94 * 2. In addition, measuring the sum of evictions and activations (E)
95 * at the time of a page's eviction, and comparing it to another
96 * reading (R) at the time the page faults back into memory tells
97 * the minimum number of accesses while the page was not cached.
98 * This is called the refault distance.
100 * Because the first access of the page was the fault and the second
101 * access the refault, we combine the in-cache distance with the
102 * out-of-cache distance to get the complete minimum access distance
103 * of this page:
105 * NR_inactive + (R - E)
107 * And knowing the minimum access distance of a page, we can easily
108 * tell if the page would be able to stay in cache assuming all page
109 * slots in the cache were available:
111 * NR_inactive + (R - E) <= NR_inactive + NR_active
113 * which can be further simplified to
115 * (R - E) <= NR_active
117 * Put into words, the refault distance (out-of-cache) can be seen as
118 * a deficit in inactive list space (in-cache). If the inactive list
119 * had (R - E) more page slots, the page would not have been evicted
120 * in between accesses, but activated instead. And on a full system,
121 * the only thing eating into inactive list space is active pages.
124 * Refaulting inactive pages
126 * All that is known about the active list is that the pages have been
127 * accessed more than once in the past. This means that at any given
128 * time there is actually a good chance that pages on the active list
129 * are no longer in active use.
131 * So when a refault distance of (R - E) is observed and there are at
132 * least (R - E) active pages, the refaulting page is activated
133 * optimistically in the hope that (R - E) active pages are actually
134 * used less frequently than the refaulting page - or even not used at
135 * all anymore.
137 * That means if inactive cache is refaulting with a suitable refault
138 * distance, we assume the cache workingset is transitioning and put
139 * pressure on the current active list.
141 * If this is wrong and demotion kicks in, the pages which are truly
142 * used more frequently will be reactivated while the less frequently
143 * used once will be evicted from memory.
145 * But if this is right, the stale pages will be pushed out of memory
146 * and the used pages get to stay in cache.
148 * Refaulting active pages
150 * If on the other hand the refaulting pages have recently been
151 * deactivated, it means that the active list is no longer protecting
152 * actively used cache from reclaim. The cache is NOT transitioning to
153 * a different workingset; the existing workingset is thrashing in the
154 * space allocated to the page cache.
157 * Implementation
159 * For each node's LRU lists, a counter for inactive evictions and
160 * activations is maintained (node->nonresident_age).
162 * On eviction, a snapshot of this counter (along with some bits to
163 * identify the node) is stored in the now empty page cache
164 * slot of the evicted page. This is called a shadow entry.
166 * On cache misses for which there are shadow entries, an eligible
167 * refault distance will immediately activate the refaulting page.
170 #define EVICTION_SHIFT ((BITS_PER_LONG - BITS_PER_XA_VALUE) + \
171 1 + NODES_SHIFT + MEM_CGROUP_ID_SHIFT)
172 #define EVICTION_MASK (~0UL >> EVICTION_SHIFT)
175 * Eviction timestamps need to be able to cover the full range of
176 * actionable refaults. However, bits are tight in the xarray
177 * entry, and after storing the identifier for the lruvec there might
178 * not be enough left to represent every single actionable refault. In
179 * that case, we have to sacrifice granularity for distance, and group
180 * evictions into coarser buckets by shaving off lower timestamp bits.
182 static unsigned int bucket_order __read_mostly;
184 static void *pack_shadow(int memcgid, pg_data_t *pgdat, unsigned long eviction,
185 bool workingset)
187 eviction >>= bucket_order;
188 eviction &= EVICTION_MASK;
189 eviction = (eviction << MEM_CGROUP_ID_SHIFT) | memcgid;
190 eviction = (eviction << NODES_SHIFT) | pgdat->node_id;
191 eviction = (eviction << 1) | workingset;
193 return xa_mk_value(eviction);
196 static void unpack_shadow(void *shadow, int *memcgidp, pg_data_t **pgdat,
197 unsigned long *evictionp, bool *workingsetp)
199 unsigned long entry = xa_to_value(shadow);
200 int memcgid, nid;
201 bool workingset;
203 workingset = entry & 1;
204 entry >>= 1;
205 nid = entry & ((1UL << NODES_SHIFT) - 1);
206 entry >>= NODES_SHIFT;
207 memcgid = entry & ((1UL << MEM_CGROUP_ID_SHIFT) - 1);
208 entry >>= MEM_CGROUP_ID_SHIFT;
210 *memcgidp = memcgid;
211 *pgdat = NODE_DATA(nid);
212 *evictionp = entry << bucket_order;
213 *workingsetp = workingset;
217 * workingset_age_nonresident - age non-resident entries as LRU ages
218 * @memcg: the lruvec that was aged
219 * @nr_pages: the number of pages to count
221 * As in-memory pages are aged, non-resident pages need to be aged as
222 * well, in order for the refault distances later on to be comparable
223 * to the in-memory dimensions. This function allows reclaim and LRU
224 * operations to drive the non-resident aging along in parallel.
226 void workingset_age_nonresident(struct lruvec *lruvec, unsigned long nr_pages)
229 * Reclaiming a cgroup means reclaiming all its children in a
230 * round-robin fashion. That means that each cgroup has an LRU
231 * order that is composed of the LRU orders of its child
232 * cgroups; and every page has an LRU position not just in the
233 * cgroup that owns it, but in all of that group's ancestors.
235 * So when the physical inactive list of a leaf cgroup ages,
236 * the virtual inactive lists of all its parents, including
237 * the root cgroup's, age as well.
239 do {
240 atomic_long_add(nr_pages, &lruvec->nonresident_age);
241 } while ((lruvec = parent_lruvec(lruvec)));
245 * workingset_eviction - note the eviction of a page from memory
246 * @target_memcg: the cgroup that is causing the reclaim
247 * @page: the page being evicted
249 * Returns a shadow entry to be stored in @page->mapping->i_pages in place
250 * of the evicted @page so that a later refault can be detected.
252 void *workingset_eviction(struct page *page, struct mem_cgroup *target_memcg)
254 struct pglist_data *pgdat = page_pgdat(page);
255 unsigned long eviction;
256 struct lruvec *lruvec;
257 int memcgid;
259 /* Page is fully exclusive and pins page->mem_cgroup */
260 VM_BUG_ON_PAGE(PageLRU(page), page);
261 VM_BUG_ON_PAGE(page_count(page), page);
262 VM_BUG_ON_PAGE(!PageLocked(page), page);
264 lruvec = mem_cgroup_lruvec(target_memcg, pgdat);
265 workingset_age_nonresident(lruvec, hpage_nr_pages(page));
266 /* XXX: target_memcg can be NULL, go through lruvec */
267 memcgid = mem_cgroup_id(lruvec_memcg(lruvec));
268 eviction = atomic_long_read(&lruvec->nonresident_age);
269 return pack_shadow(memcgid, pgdat, eviction, PageWorkingset(page));
273 * workingset_refault - evaluate the refault of a previously evicted page
274 * @page: the freshly allocated replacement page
275 * @shadow: shadow entry of the evicted page
277 * Calculates and evaluates the refault distance of the previously
278 * evicted page in the context of the node and the memcg whose memory
279 * pressure caused the eviction.
281 void workingset_refault(struct page *page, void *shadow)
283 struct mem_cgroup *eviction_memcg;
284 struct lruvec *eviction_lruvec;
285 unsigned long refault_distance;
286 unsigned long workingset_size;
287 struct pglist_data *pgdat;
288 struct mem_cgroup *memcg;
289 unsigned long eviction;
290 struct lruvec *lruvec;
291 unsigned long refault;
292 bool workingset;
293 int memcgid;
295 unpack_shadow(shadow, &memcgid, &pgdat, &eviction, &workingset);
297 rcu_read_lock();
299 * Look up the memcg associated with the stored ID. It might
300 * have been deleted since the page's eviction.
302 * Note that in rare events the ID could have been recycled
303 * for a new cgroup that refaults a shared page. This is
304 * impossible to tell from the available data. However, this
305 * should be a rare and limited disturbance, and activations
306 * are always speculative anyway. Ultimately, it's the aging
307 * algorithm's job to shake out the minimum access frequency
308 * for the active cache.
310 * XXX: On !CONFIG_MEMCG, this will always return NULL; it
311 * would be better if the root_mem_cgroup existed in all
312 * configurations instead.
314 eviction_memcg = mem_cgroup_from_id(memcgid);
315 if (!mem_cgroup_disabled() && !eviction_memcg)
316 goto out;
317 eviction_lruvec = mem_cgroup_lruvec(eviction_memcg, pgdat);
318 refault = atomic_long_read(&eviction_lruvec->nonresident_age);
321 * Calculate the refault distance
323 * The unsigned subtraction here gives an accurate distance
324 * across nonresident_age overflows in most cases. There is a
325 * special case: usually, shadow entries have a short lifetime
326 * and are either refaulted or reclaimed along with the inode
327 * before they get too old. But it is not impossible for the
328 * nonresident_age to lap a shadow entry in the field, which
329 * can then result in a false small refault distance, leading
330 * to a false activation should this old entry actually
331 * refault again. However, earlier kernels used to deactivate
332 * unconditionally with *every* reclaim invocation for the
333 * longest time, so the occasional inappropriate activation
334 * leading to pressure on the active list is not a problem.
336 refault_distance = (refault - eviction) & EVICTION_MASK;
339 * The activation decision for this page is made at the level
340 * where the eviction occurred, as that is where the LRU order
341 * during page reclaim is being determined.
343 * However, the cgroup that will own the page is the one that
344 * is actually experiencing the refault event.
346 memcg = page_memcg(page);
347 lruvec = mem_cgroup_lruvec(memcg, pgdat);
349 inc_lruvec_state(lruvec, WORKINGSET_REFAULT);
352 * Compare the distance to the existing workingset size. We
353 * don't activate pages that couldn't stay resident even if
354 * all the memory was available to the page cache. Whether
355 * cache can compete with anon or not depends on having swap.
357 workingset_size = lruvec_page_state(eviction_lruvec, NR_ACTIVE_FILE);
358 if (mem_cgroup_get_nr_swap_pages(memcg) > 0) {
359 workingset_size += lruvec_page_state(eviction_lruvec,
360 NR_INACTIVE_ANON);
361 workingset_size += lruvec_page_state(eviction_lruvec,
362 NR_ACTIVE_ANON);
364 if (refault_distance > workingset_size)
365 goto out;
367 SetPageActive(page);
368 workingset_age_nonresident(lruvec, hpage_nr_pages(page));
369 inc_lruvec_state(lruvec, WORKINGSET_ACTIVATE);
371 /* Page was active prior to eviction */
372 if (workingset) {
373 SetPageWorkingset(page);
374 /* XXX: Move to lru_cache_add() when it supports new vs putback */
375 spin_lock_irq(&page_pgdat(page)->lru_lock);
376 lru_note_cost_page(page);
377 spin_unlock_irq(&page_pgdat(page)->lru_lock);
378 inc_lruvec_state(lruvec, WORKINGSET_RESTORE);
380 out:
381 rcu_read_unlock();
385 * workingset_activation - note a page activation
386 * @page: page that is being activated
388 void workingset_activation(struct page *page)
390 struct mem_cgroup *memcg;
391 struct lruvec *lruvec;
393 rcu_read_lock();
395 * Filter non-memcg pages here, e.g. unmap can call
396 * mark_page_accessed() on VDSO pages.
398 * XXX: See workingset_refault() - this should return
399 * root_mem_cgroup even for !CONFIG_MEMCG.
401 memcg = page_memcg_rcu(page);
402 if (!mem_cgroup_disabled() && !memcg)
403 goto out;
404 lruvec = mem_cgroup_page_lruvec(page, page_pgdat(page));
405 workingset_age_nonresident(lruvec, hpage_nr_pages(page));
406 out:
407 rcu_read_unlock();
411 * Shadow entries reflect the share of the working set that does not
412 * fit into memory, so their number depends on the access pattern of
413 * the workload. In most cases, they will refault or get reclaimed
414 * along with the inode, but a (malicious) workload that streams
415 * through files with a total size several times that of available
416 * memory, while preventing the inodes from being reclaimed, can
417 * create excessive amounts of shadow nodes. To keep a lid on this,
418 * track shadow nodes and reclaim them when they grow way past the
419 * point where they would still be useful.
422 static struct list_lru shadow_nodes;
424 void workingset_update_node(struct xa_node *node)
427 * Track non-empty nodes that contain only shadow entries;
428 * unlink those that contain pages or are being freed.
430 * Avoid acquiring the list_lru lock when the nodes are
431 * already where they should be. The list_empty() test is safe
432 * as node->private_list is protected by the i_pages lock.
434 VM_WARN_ON_ONCE(!irqs_disabled()); /* For __inc_lruvec_page_state */
436 if (node->count && node->count == node->nr_values) {
437 if (list_empty(&node->private_list)) {
438 list_lru_add(&shadow_nodes, &node->private_list);
439 __inc_lruvec_slab_state(node, WORKINGSET_NODES);
441 } else {
442 if (!list_empty(&node->private_list)) {
443 list_lru_del(&shadow_nodes, &node->private_list);
444 __dec_lruvec_slab_state(node, WORKINGSET_NODES);
449 static unsigned long count_shadow_nodes(struct shrinker *shrinker,
450 struct shrink_control *sc)
452 unsigned long max_nodes;
453 unsigned long nodes;
454 unsigned long pages;
456 nodes = list_lru_shrink_count(&shadow_nodes, sc);
459 * Approximate a reasonable limit for the nodes
460 * containing shadow entries. We don't need to keep more
461 * shadow entries than possible pages on the active list,
462 * since refault distances bigger than that are dismissed.
464 * The size of the active list converges toward 100% of
465 * overall page cache as memory grows, with only a tiny
466 * inactive list. Assume the total cache size for that.
468 * Nodes might be sparsely populated, with only one shadow
469 * entry in the extreme case. Obviously, we cannot keep one
470 * node for every eligible shadow entry, so compromise on a
471 * worst-case density of 1/8th. Below that, not all eligible
472 * refaults can be detected anymore.
474 * On 64-bit with 7 xa_nodes per page and 64 slots
475 * each, this will reclaim shadow entries when they consume
476 * ~1.8% of available memory:
478 * PAGE_SIZE / xa_nodes / node_entries * 8 / PAGE_SIZE
480 #ifdef CONFIG_MEMCG
481 if (sc->memcg) {
482 struct lruvec *lruvec;
483 int i;
485 lruvec = mem_cgroup_lruvec(sc->memcg, NODE_DATA(sc->nid));
486 for (pages = 0, i = 0; i < NR_LRU_LISTS; i++)
487 pages += lruvec_page_state_local(lruvec,
488 NR_LRU_BASE + i);
489 pages += lruvec_page_state_local(lruvec, NR_SLAB_RECLAIMABLE);
490 pages += lruvec_page_state_local(lruvec, NR_SLAB_UNRECLAIMABLE);
491 } else
492 #endif
493 pages = node_present_pages(sc->nid);
495 max_nodes = pages >> (XA_CHUNK_SHIFT - 3);
497 if (!nodes)
498 return SHRINK_EMPTY;
500 if (nodes <= max_nodes)
501 return 0;
502 return nodes - max_nodes;
505 static enum lru_status shadow_lru_isolate(struct list_head *item,
506 struct list_lru_one *lru,
507 spinlock_t *lru_lock,
508 void *arg) __must_hold(lru_lock)
510 struct xa_node *node = container_of(item, struct xa_node, private_list);
511 XA_STATE(xas, node->array, 0);
512 struct address_space *mapping;
513 int ret;
516 * Page cache insertions and deletions synchroneously maintain
517 * the shadow node LRU under the i_pages lock and the
518 * lru_lock. Because the page cache tree is emptied before
519 * the inode can be destroyed, holding the lru_lock pins any
520 * address_space that has nodes on the LRU.
522 * We can then safely transition to the i_pages lock to
523 * pin only the address_space of the particular node we want
524 * to reclaim, take the node off-LRU, and drop the lru_lock.
527 mapping = container_of(node->array, struct address_space, i_pages);
529 /* Coming from the list, invert the lock order */
530 if (!xa_trylock(&mapping->i_pages)) {
531 spin_unlock_irq(lru_lock);
532 ret = LRU_RETRY;
533 goto out;
536 list_lru_isolate(lru, item);
537 __dec_lruvec_slab_state(node, WORKINGSET_NODES);
539 spin_unlock(lru_lock);
542 * The nodes should only contain one or more shadow entries,
543 * no pages, so we expect to be able to remove them all and
544 * delete and free the empty node afterwards.
546 if (WARN_ON_ONCE(!node->nr_values))
547 goto out_invalid;
548 if (WARN_ON_ONCE(node->count != node->nr_values))
549 goto out_invalid;
550 mapping->nrexceptional -= node->nr_values;
551 xas.xa_node = xa_parent_locked(&mapping->i_pages, node);
552 xas.xa_offset = node->offset;
553 xas.xa_shift = node->shift + XA_CHUNK_SHIFT;
554 xas_set_update(&xas, workingset_update_node);
556 * We could store a shadow entry here which was the minimum of the
557 * shadow entries we were tracking ...
559 xas_store(&xas, NULL);
560 __inc_lruvec_slab_state(node, WORKINGSET_NODERECLAIM);
562 out_invalid:
563 xa_unlock_irq(&mapping->i_pages);
564 ret = LRU_REMOVED_RETRY;
565 out:
566 cond_resched();
567 spin_lock_irq(lru_lock);
568 return ret;
571 static unsigned long scan_shadow_nodes(struct shrinker *shrinker,
572 struct shrink_control *sc)
574 /* list_lru lock nests inside the IRQ-safe i_pages lock */
575 return list_lru_shrink_walk_irq(&shadow_nodes, sc, shadow_lru_isolate,
576 NULL);
579 static struct shrinker workingset_shadow_shrinker = {
580 .count_objects = count_shadow_nodes,
581 .scan_objects = scan_shadow_nodes,
582 .seeks = 0, /* ->count reports only fully expendable nodes */
583 .flags = SHRINKER_NUMA_AWARE | SHRINKER_MEMCG_AWARE,
587 * Our list_lru->lock is IRQ-safe as it nests inside the IRQ-safe
588 * i_pages lock.
590 static struct lock_class_key shadow_nodes_key;
592 static int __init workingset_init(void)
594 unsigned int timestamp_bits;
595 unsigned int max_order;
596 int ret;
598 BUILD_BUG_ON(BITS_PER_LONG < EVICTION_SHIFT);
600 * Calculate the eviction bucket size to cover the longest
601 * actionable refault distance, which is currently half of
602 * memory (totalram_pages/2). However, memory hotplug may add
603 * some more pages at runtime, so keep working with up to
604 * double the initial memory by using totalram_pages as-is.
606 timestamp_bits = BITS_PER_LONG - EVICTION_SHIFT;
607 max_order = fls_long(totalram_pages() - 1);
608 if (max_order > timestamp_bits)
609 bucket_order = max_order - timestamp_bits;
610 pr_info("workingset: timestamp_bits=%d max_order=%d bucket_order=%u\n",
611 timestamp_bits, max_order, bucket_order);
613 ret = prealloc_shrinker(&workingset_shadow_shrinker);
614 if (ret)
615 goto err;
616 ret = __list_lru_init(&shadow_nodes, true, &shadow_nodes_key,
617 &workingset_shadow_shrinker);
618 if (ret)
619 goto err_list_lru;
620 register_shrinker_prepared(&workingset_shadow_shrinker);
621 return 0;
622 err_list_lru:
623 free_prealloced_shrinker(&workingset_shadow_shrinker);
624 err:
625 return ret;
627 module_init(workingset_init);