?  search:
summary | log | graphiclog1 | graphiclog2 | commit | commitdiff | tree | refs | edit | fork
blame | history | raw | HEAD
block: move down direct IO plugging
[linux/fpc-iii.git] / drivers / mtd / nand / pxa3xx_nand.c
blob252aaefcacfa2ba0e07d1425672afcaa8c665bdf
1 /*
2 * drivers/mtd/nand/pxa3xx_nand.c
3 *
4 * Copyright © 2005 Intel Corporation
5 * Copyright © 2006 Marvell International Ltd.
6 *
7 * This program is free software; you can redistribute it and/or modify
8 * it under the terms of the GNU General Public License version 2 as
9 * published by the Free Software Foundation.
10 */
11
12 #include <linux/kernel.h>
13 #include <linux/module.h>
14 #include <linux/interrupt.h>
15 #include <linux/platform_device.h>
16 #include <linux/dma-mapping.h>
17 #include <linux/delay.h>
18 #include <linux/clk.h>
19 #include <linux/mtd/mtd.h>
20 #include <linux/mtd/nand.h>
21 #include <linux/mtd/partitions.h>
22 #include <linux/io.h>
23 #include <linux/irq.h>
24 #include <linux/slab.h>
25
26 #include <mach/dma.h>
27 #include <plat/pxa3xx_nand.h>
28
29 #define CHIP_DELAY_TIMEOUT (2 * HZ/10)
30 #define NAND_STOP_DELAY (2 * HZ/50)
31 #define PAGE_CHUNK_SIZE (2048)
32
33 /* registers and bit definitions */
34 #define NDCR (0x00) /* Control register */
35 #define NDTR0CS0 (0x04) /* Timing Parameter 0 for CS0 */
36 #define NDTR1CS0 (0x0C) /* Timing Parameter 1 for CS0 */
37 #define NDSR (0x14) /* Status Register */
38 #define NDPCR (0x18) /* Page Count Register */
39 #define NDBDR0 (0x1C) /* Bad Block Register 0 */
40 #define NDBDR1 (0x20) /* Bad Block Register 1 */
41 #define NDDB (0x40) /* Data Buffer */
42 #define NDCB0 (0x48) /* Command Buffer0 */
43 #define NDCB1 (0x4C) /* Command Buffer1 */
44 #define NDCB2 (0x50) /* Command Buffer2 */
45
46 #define NDCR_SPARE_EN (0x1 << 31)
47 #define NDCR_ECC_EN (0x1 << 30)
48 #define NDCR_DMA_EN (0x1 << 29)
49 #define NDCR_ND_RUN (0x1 << 28)
50 #define NDCR_DWIDTH_C (0x1 << 27)
51 #define NDCR_DWIDTH_M (0x1 << 26)
52 #define NDCR_PAGE_SZ (0x1 << 24)
53 #define NDCR_NCSX (0x1 << 23)
54 #define NDCR_ND_MODE (0x3 << 21)
55 #define NDCR_NAND_MODE (0x0)
56 #define NDCR_CLR_PG_CNT (0x1 << 20)
57 #define NDCR_STOP_ON_UNCOR (0x1 << 19)
58 #define NDCR_RD_ID_CNT_MASK (0x7 << 16)
59 #define NDCR_RD_ID_CNT(x) (((x) << 16) & NDCR_RD_ID_CNT_MASK)
60
61 #define NDCR_RA_START (0x1 << 15)
62 #define NDCR_PG_PER_BLK (0x1 << 14)
63 #define NDCR_ND_ARB_EN (0x1 << 12)
64 #define NDCR_INT_MASK (0xFFF)
65
66 #define NDSR_MASK (0xfff)
67 #define NDSR_RDY (0x1 << 12)
68 #define NDSR_FLASH_RDY (0x1 << 11)
69 #define NDSR_CS0_PAGED (0x1 << 10)
70 #define NDSR_CS1_PAGED (0x1 << 9)
71 #define NDSR_CS0_CMDD (0x1 << 8)
72 #define NDSR_CS1_CMDD (0x1 << 7)
73 #define NDSR_CS0_BBD (0x1 << 6)
74 #define NDSR_CS1_BBD (0x1 << 5)
75 #define NDSR_DBERR (0x1 << 4)
76 #define NDSR_SBERR (0x1 << 3)
77 #define NDSR_WRDREQ (0x1 << 2)
78 #define NDSR_RDDREQ (0x1 << 1)
79 #define NDSR_WRCMDREQ (0x1)
80
81 #define NDCB0_ST_ROW_EN (0x1 << 26)
82 #define NDCB0_AUTO_RS (0x1 << 25)
83 #define NDCB0_CSEL (0x1 << 24)
84 #define NDCB0_CMD_TYPE_MASK (0x7 << 21)
85 #define NDCB0_CMD_TYPE(x) (((x) << 21) & NDCB0_CMD_TYPE_MASK)
86 #define NDCB0_NC (0x1 << 20)
87 #define NDCB0_DBC (0x1 << 19)
88 #define NDCB0_ADDR_CYC_MASK (0x7 << 16)
89 #define NDCB0_ADDR_CYC(x) (((x) << 16) & NDCB0_ADDR_CYC_MASK)
90 #define NDCB0_CMD2_MASK (0xff << 8)
91 #define NDCB0_CMD1_MASK (0xff)
92 #define NDCB0_ADDR_CYC_SHIFT (16)
93
94 /* macros for registers read/write */
95 #define nand_writel(info, off, val) \
96 __raw_writel((val), (info)->mmio_base + (off))
97
98 #define nand_readl(info, off) \
99 __raw_readl((info)->mmio_base + (off))
100
101 /* error code and state */
102 enum {
103 ERR_NONE = 0,
104 ERR_DMABUSERR = -1,
105 ERR_SENDCMD = -2,
106 ERR_DBERR = -3,
107 ERR_BBERR = -4,
108 ERR_SBERR = -5,
109 };
110
111 enum {
112 STATE_IDLE = 0,
113 STATE_PREPARED,
114 STATE_CMD_HANDLE,
115 STATE_DMA_READING,
116 STATE_DMA_WRITING,
117 STATE_DMA_DONE,
118 STATE_PIO_READING,
119 STATE_PIO_WRITING,
120 STATE_CMD_DONE,
121 STATE_READY,
122 };
123
124 struct pxa3xx_nand_host {
125 struct nand_chip chip;
126 struct pxa3xx_nand_cmdset *cmdset;
127 struct mtd_info *mtd;
128 void *info_data;
129
130 /* page size of attached chip */
131 unsigned int page_size;
132 int use_ecc;
133 int cs;
134
135 /* calculated from pxa3xx_nand_flash data */
136 unsigned int col_addr_cycles;
137 unsigned int row_addr_cycles;
138 size_t read_id_bytes;
139
140 /* cached register value */
141 uint32_t reg_ndcr;
142 uint32_t ndtr0cs0;
143 uint32_t ndtr1cs0;
144 };
145
146 struct pxa3xx_nand_info {
147 struct nand_hw_control controller;
148 struct platform_device *pdev;
149
150 struct clk *clk;
151 void __iomem *mmio_base;
152 unsigned long mmio_phys;
153 struct completion cmd_complete;
154
155 unsigned int buf_start;
156 unsigned int buf_count;
157
158 /* DMA information */
159 int drcmr_dat;
160 int drcmr_cmd;
161
162 unsigned char *data_buff;
163 unsigned char *oob_buff;
164 dma_addr_t data_buff_phys;
165 int data_dma_ch;
166 struct pxa_dma_desc *data_desc;
167 dma_addr_t data_desc_addr;
168
169 struct pxa3xx_nand_host *host[NUM_CHIP_SELECT];
170 unsigned int state;
171
172 int cs;
173 int use_ecc; /* use HW ECC ? */
174 int use_dma; /* use DMA ? */
175 int is_ready;
176
177 unsigned int page_size; /* page size of attached chip */
178 unsigned int data_size; /* data size in FIFO */
179 unsigned int oob_size;
180 int retcode;
181
182 /* generated NDCBx register values */
183 uint32_t ndcb0;
184 uint32_t ndcb1;
185 uint32_t ndcb2;
186 };
187
188 static bool use_dma = 1;
189 module_param(use_dma, bool, 0444);
190 MODULE_PARM_DESC(use_dma, "enable DMA for data transferring to/from NAND HW");
191
192 /*
193 * Default NAND flash controller configuration setup by the
194 * bootloader. This configuration is used only when pdata->keep_config is set
195 */
196 static struct pxa3xx_nand_cmdset default_cmdset = {
197 .read1 = 0x3000,
198 .read2 = 0x0050,
199 .program = 0x1080,
200 .read_status = 0x0070,
201 .read_id = 0x0090,
202 .erase = 0xD060,
203 .reset = 0x00FF,
204 .lock = 0x002A,
205 .unlock = 0x2423,
206 .lock_status = 0x007A,
207 };
208
209 static struct pxa3xx_nand_timing timing[] = {
210 { 40, 80, 60, 100, 80, 100, 90000, 400, 40, },
211 { 10, 0, 20, 40, 30, 40, 11123, 110, 10, },
212 { 10, 25, 15, 25, 15, 30, 25000, 60, 10, },
213 { 10, 35, 15, 25, 15, 25, 25000, 60, 10, },
214 };
215
216 static struct pxa3xx_nand_flash builtin_flash_types[] = {
217 { "DEFAULT FLASH", 0, 0, 2048, 8, 8, 0, &timing[0] },
218 { "64MiB 16-bit", 0x46ec, 32, 512, 16, 16, 4096, &timing[1] },
219 { "256MiB 8-bit", 0xdaec, 64, 2048, 8, 8, 2048, &timing[1] },
220 { "4GiB 8-bit", 0xd7ec, 128, 4096, 8, 8, 8192, &timing[1] },
221 { "128MiB 8-bit", 0xa12c, 64, 2048, 8, 8, 1024, &timing[2] },
222 { "128MiB 16-bit", 0xb12c, 64, 2048, 16, 16, 1024, &timing[2] },
223 { "512MiB 8-bit", 0xdc2c, 64, 2048, 8, 8, 4096, &timing[2] },
224 { "512MiB 16-bit", 0xcc2c, 64, 2048, 16, 16, 4096, &timing[2] },
225 { "256MiB 16-bit", 0xba20, 64, 2048, 16, 16, 2048, &timing[3] },
226 };
227
228 /* Define a default flash type setting serve as flash detecting only */
229 #define DEFAULT_FLASH_TYPE (&builtin_flash_types[0])
230
231 const char *mtd_names[] = {"pxa3xx_nand-0", "pxa3xx_nand-1", NULL};
232
233 #define NDTR0_tCH(c) (min((c), 7) << 19)
234 #define NDTR0_tCS(c) (min((c), 7) << 16)
235 #define NDTR0_tWH(c) (min((c), 7) << 11)
236 #define NDTR0_tWP(c) (min((c), 7) << 8)
237 #define NDTR0_tRH(c) (min((c), 7) << 3)
238 #define NDTR0_tRP(c) (min((c), 7) << 0)
239
240 #define NDTR1_tR(c) (min((c), 65535) << 16)
241 #define NDTR1_tWHR(c) (min((c), 15) << 4)
242 #define NDTR1_tAR(c) (min((c), 15) << 0)
243
244 /* convert nano-seconds to nand flash controller clock cycles */
245 #define ns2cycle(ns, clk) (int)((ns) * (clk / 1000000) / 1000)
246
247 static void pxa3xx_nand_set_timing(struct pxa3xx_nand_host *host,
248 const struct pxa3xx_nand_timing *t)
249 {
250 struct pxa3xx_nand_info *info = host->info_data;
251 unsigned long nand_clk = clk_get_rate(info->clk);
252 uint32_t ndtr0, ndtr1;
253
254 ndtr0 = NDTR0_tCH(ns2cycle(t->tCH, nand_clk)) |
255 NDTR0_tCS(ns2cycle(t->tCS, nand_clk)) |
256 NDTR0_tWH(ns2cycle(t->tWH, nand_clk)) |
257 NDTR0_tWP(ns2cycle(t->tWP, nand_clk)) |
258 NDTR0_tRH(ns2cycle(t->tRH, nand_clk)) |
259 NDTR0_tRP(ns2cycle(t->tRP, nand_clk));
260
261 ndtr1 = NDTR1_tR(ns2cycle(t->tR, nand_clk)) |
262 NDTR1_tWHR(ns2cycle(t->tWHR, nand_clk)) |
263 NDTR1_tAR(ns2cycle(t->tAR, nand_clk));
264
265 host->ndtr0cs0 = ndtr0;
266 host->ndtr1cs0 = ndtr1;
267 nand_writel(info, NDTR0CS0, ndtr0);
268 nand_writel(info, NDTR1CS0, ndtr1);
269 }
270
271 static void pxa3xx_set_datasize(struct pxa3xx_nand_info *info)
272 {
273 struct pxa3xx_nand_host *host = info->host[info->cs];
274 int oob_enable = host->reg_ndcr & NDCR_SPARE_EN;
275
276 info->data_size = host->page_size;
277 if (!oob_enable) {
278 info->oob_size = 0;
279 return;
280 }
281
282 switch (host->page_size) {
283 case 2048:
284 info->oob_size = (info->use_ecc) ? 40 : 64;
285 break;
286 case 512:
287 info->oob_size = (info->use_ecc) ? 8 : 16;
288 break;
289 }
290 }
291
292 /**
293 * NOTE: it is a must to set ND_RUN firstly, then write
294 * command buffer, otherwise, it does not work.
295 * We enable all the interrupt at the same time, and
296 * let pxa3xx_nand_irq to handle all logic.
297 */
298 static void pxa3xx_nand_start(struct pxa3xx_nand_info *info)
299 {
300 struct pxa3xx_nand_host *host = info->host[info->cs];
301 uint32_t ndcr;
302
303 ndcr = host->reg_ndcr;
304 ndcr |= info->use_ecc ? NDCR_ECC_EN : 0;
305 ndcr |= info->use_dma ? NDCR_DMA_EN : 0;
306 ndcr |= NDCR_ND_RUN;
307
308 /* clear status bits and run */
309 nand_writel(info, NDCR, 0);
310 nand_writel(info, NDSR, NDSR_MASK);
311 nand_writel(info, NDCR, ndcr);
312 }
313
314 static void pxa3xx_nand_stop(struct pxa3xx_nand_info *info)
315 {
316 uint32_t ndcr;
317 int timeout = NAND_STOP_DELAY;
318
319 /* wait RUN bit in NDCR become 0 */
320 ndcr = nand_readl(info, NDCR);
321 while ((ndcr & NDCR_ND_RUN) && (timeout-- > 0)) {
322 ndcr = nand_readl(info, NDCR);
323 udelay(1);
324 }
325
326 if (timeout <= 0) {
327 ndcr &= ~NDCR_ND_RUN;
328 nand_writel(info, NDCR, ndcr);
329 }
330 /* clear status bits */
331 nand_writel(info, NDSR, NDSR_MASK);
332 }
333
334 static void enable_int(struct pxa3xx_nand_info *info, uint32_t int_mask)
335 {
336 uint32_t ndcr;
337
338 ndcr = nand_readl(info, NDCR);
339 nand_writel(info, NDCR, ndcr & ~int_mask);
340 }
341
342 static void disable_int(struct pxa3xx_nand_info *info, uint32_t int_mask)
343 {
344 uint32_t ndcr;
345
346 ndcr = nand_readl(info, NDCR);
347 nand_writel(info, NDCR, ndcr | int_mask);
348 }
349
350 static void handle_data_pio(struct pxa3xx_nand_info *info)
351 {
352 switch (info->state) {
353 case STATE_PIO_WRITING:
354 __raw_writesl(info->mmio_base + NDDB, info->data_buff,
355 DIV_ROUND_UP(info->data_size, 4));
356 if (info->oob_size > 0)
357 __raw_writesl(info->mmio_base + NDDB, info->oob_buff,
358 DIV_ROUND_UP(info->oob_size, 4));
359 break;
360 case STATE_PIO_READING:
361 __raw_readsl(info->mmio_base + NDDB, info->data_buff,
362 DIV_ROUND_UP(info->data_size, 4));
363 if (info->oob_size > 0)
364 __raw_readsl(info->mmio_base + NDDB, info->oob_buff,
365 DIV_ROUND_UP(info->oob_size, 4));
366 break;
367 default:
368 dev_err(&info->pdev->dev, "%s: invalid state %d\n", __func__,
369 info->state);
370 BUG();
371 }
372 }
373
374 static void start_data_dma(struct pxa3xx_nand_info *info)
375 {
376 struct pxa_dma_desc *desc = info->data_desc;
377 int dma_len = ALIGN(info->data_size + info->oob_size, 32);
378
379 desc->ddadr = DDADR_STOP;
380 desc->dcmd = DCMD_ENDIRQEN | DCMD_WIDTH4 | DCMD_BURST32 | dma_len;
381
382 switch (info->state) {
383 case STATE_DMA_WRITING:
384 desc->dsadr = info->data_buff_phys;
385 desc->dtadr = info->mmio_phys + NDDB;
386 desc->dcmd |= DCMD_INCSRCADDR | DCMD_FLOWTRG;
387 break;
388 case STATE_DMA_READING:
389 desc->dtadr = info->data_buff_phys;
390 desc->dsadr = info->mmio_phys + NDDB;
391 desc->dcmd |= DCMD_INCTRGADDR | DCMD_FLOWSRC;
392 break;
393 default:
394 dev_err(&info->pdev->dev, "%s: invalid state %d\n", __func__,
395 info->state);
396 BUG();
397 }
398
399 DRCMR(info->drcmr_dat) = DRCMR_MAPVLD | info->data_dma_ch;
400 DDADR(info->data_dma_ch) = info->data_desc_addr;
401 DCSR(info->data_dma_ch) |= DCSR_RUN;
402 }
403
404 static void pxa3xx_nand_data_dma_irq(int channel, void *data)
405 {
406 struct pxa3xx_nand_info *info = data;
407 uint32_t dcsr;
408
409 dcsr = DCSR(channel);
410 DCSR(channel) = dcsr;
411
412 if (dcsr & DCSR_BUSERR) {
413 info->retcode = ERR_DMABUSERR;
414 }
415
416 info->state = STATE_DMA_DONE;
417 enable_int(info, NDCR_INT_MASK);
418 nand_writel(info, NDSR, NDSR_WRDREQ | NDSR_RDDREQ);
419 }
420
421 static irqreturn_t pxa3xx_nand_irq(int irq, void *devid)
422 {
423 struct pxa3xx_nand_info *info = devid;
424 unsigned int status, is_completed = 0;
425 unsigned int ready, cmd_done;
426
427 if (info->cs == 0) {
428 ready = NDSR_FLASH_RDY;
429 cmd_done = NDSR_CS0_CMDD;
430 } else {
431 ready = NDSR_RDY;
432 cmd_done = NDSR_CS1_CMDD;
433 }
434
435 status = nand_readl(info, NDSR);
436
437 if (status & NDSR_DBERR)
438 info->retcode = ERR_DBERR;
439 if (status & NDSR_SBERR)
440 info->retcode = ERR_SBERR;
441 if (status & (NDSR_RDDREQ | NDSR_WRDREQ)) {
442 /* whether use dma to transfer data */
443 if (info->use_dma) {
444 disable_int(info, NDCR_INT_MASK);
445 info->state = (status & NDSR_RDDREQ) ?
446 STATE_DMA_READING : STATE_DMA_WRITING;
447 start_data_dma(info);
448 goto NORMAL_IRQ_EXIT;
449 } else {
450 info->state = (status & NDSR_RDDREQ) ?
451 STATE_PIO_READING : STATE_PIO_WRITING;
452 handle_data_pio(info);
453 }
454 }
455 if (status & cmd_done) {
456 info->state = STATE_CMD_DONE;
457 is_completed = 1;
458 }
459 if (status & ready) {
460 info->is_ready = 1;
461 info->state = STATE_READY;
462 }
463
464 if (status & NDSR_WRCMDREQ) {
465 nand_writel(info, NDSR, NDSR_WRCMDREQ);
466 status &= ~NDSR_WRCMDREQ;
467 info->state = STATE_CMD_HANDLE;
468 nand_writel(info, NDCB0, info->ndcb0);
469 nand_writel(info, NDCB0, info->ndcb1);
470 nand_writel(info, NDCB0, info->ndcb2);
471 }
472
473 /* clear NDSR to let the controller exit the IRQ */
474 nand_writel(info, NDSR, status);
475 if (is_completed)
476 complete(&info->cmd_complete);
477 NORMAL_IRQ_EXIT:
478 return IRQ_HANDLED;
479 }
480
481 static inline int is_buf_blank(uint8_t *buf, size_t len)
482 {
483 for (; len > 0; len--)
484 if (*buf++ != 0xff)
485 return 0;
486 return 1;
487 }
488
489 static int prepare_command_pool(struct pxa3xx_nand_info *info, int command,
490 uint16_t column, int page_addr)
491 {
492 uint16_t cmd;
493 int addr_cycle, exec_cmd;
494 struct pxa3xx_nand_host *host;
495 struct mtd_info *mtd;
496
497 host = info->host[info->cs];
498 mtd = host->mtd;
499 addr_cycle = 0;
500 exec_cmd = 1;
501
502 /* reset data and oob column point to handle data */
503 info->buf_start = 0;
504 info->buf_count = 0;
505 info->oob_size = 0;
506 info->use_ecc = 0;
507 info->is_ready = 0;
508 info->retcode = ERR_NONE;
509 if (info->cs != 0)
510 info->ndcb0 = NDCB0_CSEL;
511 else
512 info->ndcb0 = 0;
513
514 switch (command) {
515 case NAND_CMD_READ0:
516 case NAND_CMD_PAGEPROG:
517 info->use_ecc = 1;
518 case NAND_CMD_READOOB:
519 pxa3xx_set_datasize(info);
520 break;
521 case NAND_CMD_SEQIN:
522 exec_cmd = 0;
523 break;
524 default:
525 info->ndcb1 = 0;
526 info->ndcb2 = 0;
527 break;
528 }
529
530 addr_cycle = NDCB0_ADDR_CYC(host->row_addr_cycles
531 + host->col_addr_cycles);
532
533 switch (command) {
534 case NAND_CMD_READOOB:
535 case NAND_CMD_READ0:
536 cmd = host->cmdset->read1;
537 if (command == NAND_CMD_READOOB)
538 info->buf_start = mtd->writesize + column;
539 else
540 info->buf_start = column;
541
542 if (unlikely(host->page_size < PAGE_CHUNK_SIZE))
543 info->ndcb0 |= NDCB0_CMD_TYPE(0)
544 | addr_cycle
545 | (cmd & NDCB0_CMD1_MASK);
546 else
547 info->ndcb0 |= NDCB0_CMD_TYPE(0)
548 | NDCB0_DBC
549 | addr_cycle
550 | cmd;
551
552 case NAND_CMD_SEQIN:
553 /* small page addr setting */
554 if (unlikely(host->page_size < PAGE_CHUNK_SIZE)) {
555 info->ndcb1 = ((page_addr & 0xFFFFFF) << 8)
556 | (column & 0xFF);
557
558 info->ndcb2 = 0;
559 } else {
560 info->ndcb1 = ((page_addr & 0xFFFF) << 16)
561 | (column & 0xFFFF);
562
563 if (page_addr & 0xFF0000)
564 info->ndcb2 = (page_addr & 0xFF0000) >> 16;
565 else
566 info->ndcb2 = 0;
567 }
568
569 info->buf_count = mtd->writesize + mtd->oobsize;
570 memset(info->data_buff, 0xFF, info->buf_count);
571
572 break;
573
574 case NAND_CMD_PAGEPROG:
575 if (is_buf_blank(info->data_buff,
576 (mtd->writesize + mtd->oobsize))) {
577 exec_cmd = 0;
578 break;
579 }
580
581 cmd = host->cmdset->program;
582 info->ndcb0 |= NDCB0_CMD_TYPE(0x1)
583 | NDCB0_AUTO_RS
584 | NDCB0_ST_ROW_EN
585 | NDCB0_DBC
586 | cmd
587 | addr_cycle;
588 break;
589
590 case NAND_CMD_READID:
591 cmd = host->cmdset->read_id;
592 info->buf_count = host->read_id_bytes;
593 info->ndcb0 |= NDCB0_CMD_TYPE(3)
594 | NDCB0_ADDR_CYC(1)
595 | cmd;
596
597 info->data_size = 8;
598 break;
599 case NAND_CMD_STATUS:
600 cmd = host->cmdset->read_status;
601 info->buf_count = 1;
602 info->ndcb0 |= NDCB0_CMD_TYPE(4)
603 | NDCB0_ADDR_CYC(1)
604 | cmd;
605
606 info->data_size = 8;
607 break;
608
609 case NAND_CMD_ERASE1:
610 cmd = host->cmdset->erase;
611 info->ndcb0 |= NDCB0_CMD_TYPE(2)
612 | NDCB0_AUTO_RS
613 | NDCB0_ADDR_CYC(3)
614 | NDCB0_DBC
615 | cmd;
616 info->ndcb1 = page_addr;
617 info->ndcb2 = 0;
618
619 break;
620 case NAND_CMD_RESET:
621 cmd = host->cmdset->reset;
622 info->ndcb0 |= NDCB0_CMD_TYPE(5)
623 | cmd;
624
625 break;
626
627 case NAND_CMD_ERASE2:
628 exec_cmd = 0;
629 break;
630
631 default:
632 exec_cmd = 0;
633 dev_err(&info->pdev->dev, "non-supported command %x\n",
634 command);
635 break;
636 }
637
638 return exec_cmd;
639 }
640
641 static void pxa3xx_nand_cmdfunc(struct mtd_info *mtd, unsigned command,
642 int column, int page_addr)
643 {
644 struct pxa3xx_nand_host *host = mtd->priv;
645 struct pxa3xx_nand_info *info = host->info_data;
646 int ret, exec_cmd;
647
648 /*
649 * if this is a x16 device ,then convert the input
650 * "byte" address into a "word" address appropriate
651 * for indexing a word-oriented device
652 */
653 if (host->reg_ndcr & NDCR_DWIDTH_M)
654 column /= 2;
655
656 /*
657 * There may be different NAND chip hooked to
658 * different chip select, so check whether
659 * chip select has been changed, if yes, reset the timing
660 */
661 if (info->cs != host->cs) {
662 info->cs = host->cs;
663 nand_writel(info, NDTR0CS0, host->ndtr0cs0);
664 nand_writel(info, NDTR1CS0, host->ndtr1cs0);
665 }
666
667 info->state = STATE_PREPARED;
668 exec_cmd = prepare_command_pool(info, command, column, page_addr);
669 if (exec_cmd) {
670 init_completion(&info->cmd_complete);
671 pxa3xx_nand_start(info);
672
673 ret = wait_for_completion_timeout(&info->cmd_complete,
674 CHIP_DELAY_TIMEOUT);
675 if (!ret) {
676 dev_err(&info->pdev->dev, "Wait time out!!!\n");
677 /* Stop State Machine for next command cycle */
678 pxa3xx_nand_stop(info);
679 }
680 }
681 info->state = STATE_IDLE;
682 }
683
684 static void pxa3xx_nand_write_page_hwecc(struct mtd_info *mtd,
685 struct nand_chip *chip, const uint8_t *buf, int oob_required)
686 {
687 chip->write_buf(mtd, buf, mtd->writesize);
688 chip->write_buf(mtd, chip->oob_poi, mtd->oobsize);
689 }
690
691 static int pxa3xx_nand_read_page_hwecc(struct mtd_info *mtd,
692 struct nand_chip *chip, uint8_t *buf, int oob_required,
693 int page)
694 {
695 struct pxa3xx_nand_host *host = mtd->priv;
696 struct pxa3xx_nand_info *info = host->info_data;
697
698 chip->read_buf(mtd, buf, mtd->writesize);
699 chip->read_buf(mtd, chip->oob_poi, mtd->oobsize);
700
701 if (info->retcode == ERR_SBERR) {
702 switch (info->use_ecc) {
703 case 1:
704 mtd->ecc_stats.corrected++;
705 break;
706 case 0:
707 default:
708 break;
709 }
710 } else if (info->retcode == ERR_DBERR) {
711 /*
712 * for blank page (all 0xff), HW will calculate its ECC as
713 * 0, which is different from the ECC information within
714 * OOB, ignore such double bit errors
715 */
716 if (is_buf_blank(buf, mtd->writesize))
717 info->retcode = ERR_NONE;
718 else
719 mtd->ecc_stats.failed++;
720 }
721
722 return 0;
723 }
724
725 static uint8_t pxa3xx_nand_read_byte(struct mtd_info *mtd)
726 {
727 struct pxa3xx_nand_host *host = mtd->priv;
728 struct pxa3xx_nand_info *info = host->info_data;
729 char retval = 0xFF;
730
731 if (info->buf_start < info->buf_count)
732 /* Has just send a new command? */
733 retval = info->data_buff[info->buf_start++];
734
735 return retval;
736 }
737
738 static u16 pxa3xx_nand_read_word(struct mtd_info *mtd)
739 {
740 struct pxa3xx_nand_host *host = mtd->priv;
741 struct pxa3xx_nand_info *info = host->info_data;
742 u16 retval = 0xFFFF;
743
744 if (!(info->buf_start & 0x01) && info->buf_start < info->buf_count) {
745 retval = *((u16 *)(info->data_buff+info->buf_start));
746 info->buf_start += 2;
747 }
748 return retval;
749 }
750
751 static void pxa3xx_nand_read_buf(struct mtd_info *mtd, uint8_t *buf, int len)
752 {
753 struct pxa3xx_nand_host *host = mtd->priv;
754 struct pxa3xx_nand_info *info = host->info_data;
755 int real_len = min_t(size_t, len, info->buf_count - info->buf_start);
756
757 memcpy(buf, info->data_buff + info->buf_start, real_len);
758 info->buf_start += real_len;
759 }
760
761 static void pxa3xx_nand_write_buf(struct mtd_info *mtd,
762 const uint8_t *buf, int len)
763 {
764 struct pxa3xx_nand_host *host = mtd->priv;
765 struct pxa3xx_nand_info *info = host->info_data;
766 int real_len = min_t(size_t, len, info->buf_count - info->buf_start);
767
768 memcpy(info->data_buff + info->buf_start, buf, real_len);
769 info->buf_start += real_len;
770 }
771
772 static int pxa3xx_nand_verify_buf(struct mtd_info *mtd,
773 const uint8_t *buf, int len)
774 {
775 return 0;
776 }
777
778 static void pxa3xx_nand_select_chip(struct mtd_info *mtd, int chip)
779 {
780 return;
781 }
782
783 static int pxa3xx_nand_waitfunc(struct mtd_info *mtd, struct nand_chip *this)
784 {
785 struct pxa3xx_nand_host *host = mtd->priv;
786 struct pxa3xx_nand_info *info = host->info_data;
787
788 /* pxa3xx_nand_send_command has waited for command complete */
789 if (this->state == FL_WRITING || this->state == FL_ERASING) {
790 if (info->retcode == ERR_NONE)
791 return 0;
792 else {
793 /*
794 * any error make it return 0x01 which will tell
795 * the caller the erase and write fail
796 */
797 return 0x01;
798 }
799 }
800
801 return 0;
802 }
803
804 static int pxa3xx_nand_config_flash(struct pxa3xx_nand_info *info,
805 const struct pxa3xx_nand_flash *f)
806 {
807 struct platform_device *pdev = info->pdev;
808 struct pxa3xx_nand_platform_data *pdata = pdev->dev.platform_data;
809 struct pxa3xx_nand_host *host = info->host[info->cs];
810 uint32_t ndcr = 0x0; /* enable all interrupts */
811
812 if (f->page_size != 2048 && f->page_size != 512) {
813 dev_err(&pdev->dev, "Current only support 2048 and 512 size\n");
814 return -EINVAL;
815 }
816
817 if (f->flash_width != 16 && f->flash_width != 8) {
818 dev_err(&pdev->dev, "Only support 8bit and 16 bit!\n");
819 return -EINVAL;
820 }
821
822 /* calculate flash information */
823 host->cmdset = &default_cmdset;
824 host->page_size = f->page_size;
825 host->read_id_bytes = (f->page_size == 2048) ? 4 : 2;
826
827 /* calculate addressing information */
828 host->col_addr_cycles = (f->page_size == 2048) ? 2 : 1;
829
830 if (f->num_blocks * f->page_per_block > 65536)
831 host->row_addr_cycles = 3;
832 else
833 host->row_addr_cycles = 2;
834
835 ndcr |= (pdata->enable_arbiter) ? NDCR_ND_ARB_EN : 0;
836 ndcr |= (host->col_addr_cycles == 2) ? NDCR_RA_START : 0;
837 ndcr |= (f->page_per_block == 64) ? NDCR_PG_PER_BLK : 0;
838 ndcr |= (f->page_size == 2048) ? NDCR_PAGE_SZ : 0;
839 ndcr |= (f->flash_width == 16) ? NDCR_DWIDTH_M : 0;
840 ndcr |= (f->dfc_width == 16) ? NDCR_DWIDTH_C : 0;
841
842 ndcr |= NDCR_RD_ID_CNT(host->read_id_bytes);
843 ndcr |= NDCR_SPARE_EN; /* enable spare by default */
844
845 host->reg_ndcr = ndcr;
846
847 pxa3xx_nand_set_timing(host, f->timing);
848 return 0;
849 }
850
851 static int pxa3xx_nand_detect_config(struct pxa3xx_nand_info *info)
852 {
853 /*
854 * We set 0 by hard coding here, for we don't support keep_config
855 * when there is more than one chip attached to the controller
856 */
857 struct pxa3xx_nand_host *host = info->host[0];
858 uint32_t ndcr = nand_readl(info, NDCR);
859
860 if (ndcr & NDCR_PAGE_SZ) {
861 host->page_size = 2048;
862 host->read_id_bytes = 4;
863 } else {
864 host->page_size = 512;
865 host->read_id_bytes = 2;
866 }
867
868 host->reg_ndcr = ndcr & ~NDCR_INT_MASK;
869 host->cmdset = &default_cmdset;
870
871 host->ndtr0cs0 = nand_readl(info, NDTR0CS0);
872 host->ndtr1cs0 = nand_readl(info, NDTR1CS0);
873
874 return 0;
875 }
876
877 /* the maximum possible buffer size for large page with OOB data
878 * is: 2048 + 64 = 2112 bytes, allocate a page here for both the
879 * data buffer and the DMA descriptor
880 */
881 #define MAX_BUFF_SIZE PAGE_SIZE
882
883 static int pxa3xx_nand_init_buff(struct pxa3xx_nand_info *info)
884 {
885 struct platform_device *pdev = info->pdev;
886 int data_desc_offset = MAX_BUFF_SIZE - sizeof(struct pxa_dma_desc);
887
888 if (use_dma == 0) {
889 info->data_buff = kmalloc(MAX_BUFF_SIZE, GFP_KERNEL);
890 if (info->data_buff == NULL)
891 return -ENOMEM;
892 return 0;
893 }
894
895 info->data_buff = dma_alloc_coherent(&pdev->dev, MAX_BUFF_SIZE,
896 &info->data_buff_phys, GFP_KERNEL);
897 if (info->data_buff == NULL) {
898 dev_err(&pdev->dev, "failed to allocate dma buffer\n");
899 return -ENOMEM;
900 }
901
902 info->data_desc = (void *)info->data_buff + data_desc_offset;
903 info->data_desc_addr = info->data_buff_phys + data_desc_offset;
904
905 info->data_dma_ch = pxa_request_dma("nand-data", DMA_PRIO_LOW,
906 pxa3xx_nand_data_dma_irq, info);
907 if (info->data_dma_ch < 0) {
908 dev_err(&pdev->dev, "failed to request data dma\n");
909 dma_free_coherent(&pdev->dev, MAX_BUFF_SIZE,
910 info->data_buff, info->data_buff_phys);
911 return info->data_dma_ch;
912 }
913
914 return 0;
915 }
916
917 static int pxa3xx_nand_sensing(struct pxa3xx_nand_info *info)
918 {
919 struct mtd_info *mtd;
920 int ret;
921 mtd = info->host[info->cs]->mtd;
922 /* use the common timing to make a try */
923 ret = pxa3xx_nand_config_flash(info, &builtin_flash_types[0]);
924 if (ret)
925 return ret;
926
927 pxa3xx_nand_cmdfunc(mtd, NAND_CMD_RESET, 0, 0);
928 if (info->is_ready)
929 return 0;
930
931 return -ENODEV;
932 }
933
934 static int pxa3xx_nand_scan(struct mtd_info *mtd)
935 {
936 struct pxa3xx_nand_host *host = mtd->priv;
937 struct pxa3xx_nand_info *info = host->info_data;
938 struct platform_device *pdev = info->pdev;
939 struct pxa3xx_nand_platform_data *pdata = pdev->dev.platform_data;
940 struct nand_flash_dev pxa3xx_flash_ids[2], *def = NULL;
941 const struct pxa3xx_nand_flash *f = NULL;
942 struct nand_chip *chip = mtd->priv;
943 uint32_t id = -1;
944 uint64_t chipsize;
945 int i, ret, num;
946
947 if (pdata->keep_config && !pxa3xx_nand_detect_config(info))
948 goto KEEP_CONFIG;
949
950 ret = pxa3xx_nand_sensing(info);
951 if (ret) {
952 dev_info(&info->pdev->dev, "There is no chip on cs %d!\n",
953 info->cs);
954
955 return ret;
956 }
957
958 chip->cmdfunc(mtd, NAND_CMD_READID, 0, 0);
959 id = *((uint16_t *)(info->data_buff));
960 if (id != 0)
961 dev_info(&info->pdev->dev, "Detect a flash id %x\n", id);
962 else {
963 dev_warn(&info->pdev->dev,
964 "Read out ID 0, potential timing set wrong!!\n");
965
966 return -EINVAL;
967 }
968
969 num = ARRAY_SIZE(builtin_flash_types) + pdata->num_flash - 1;
970 for (i = 0; i < num; i++) {
971 if (i < pdata->num_flash)
972 f = pdata->flash + i;
973 else
974 f = &builtin_flash_types[i - pdata->num_flash + 1];
975
976 /* find the chip in default list */
977 if (f->chip_id == id)
978 break;
979 }
980
981 if (i >= (ARRAY_SIZE(builtin_flash_types) + pdata->num_flash - 1)) {
982 dev_err(&info->pdev->dev, "ERROR!! flash not defined!!!\n");
983
984 return -EINVAL;
985 }
986
987 ret = pxa3xx_nand_config_flash(info, f);
988 if (ret) {
989 dev_err(&info->pdev->dev, "ERROR! Configure failed\n");
990 return ret;
991 }
992
993 pxa3xx_flash_ids[0].name = f->name;
994 pxa3xx_flash_ids[0].id = (f->chip_id >> 8) & 0xffff;
995 pxa3xx_flash_ids[0].pagesize = f->page_size;
996 chipsize = (uint64_t)f->num_blocks * f->page_per_block * f->page_size;
997 pxa3xx_flash_ids[0].chipsize = chipsize >> 20;
998 pxa3xx_flash_ids[0].erasesize = f->page_size * f->page_per_block;
999 if (f->flash_width == 16)
1000 pxa3xx_flash_ids[0].options = NAND_BUSWIDTH_16;
1001 pxa3xx_flash_ids[1].name = NULL;
1002 def = pxa3xx_flash_ids;
1003 KEEP_CONFIG:
1004 chip->ecc.mode = NAND_ECC_HW;
1005 chip->ecc.size = host->page_size;
1006 chip->ecc.strength = 1;
1007
1008 chip->options |= NAND_NO_READRDY;
1009 if (host->reg_ndcr & NDCR_DWIDTH_M)
1010 chip->options |= NAND_BUSWIDTH_16;
1011
1012 if (nand_scan_ident(mtd, 1, def))
1013 return -ENODEV;
1014 /* calculate addressing information */
1015 if (mtd->writesize >= 2048)
1016 host->col_addr_cycles = 2;
1017 else
1018 host->col_addr_cycles = 1;
1019
1020 info->oob_buff = info->data_buff + mtd->writesize;
1021 if ((mtd->size >> chip->page_shift) > 65536)
1022 host->row_addr_cycles = 3;
1023 else
1024 host->row_addr_cycles = 2;
1025
1026 mtd->name = mtd_names[0];
1027 return nand_scan_tail(mtd);
1028 }
1029
1030 static int alloc_nand_resource(struct platform_device *pdev)
1031 {
1032 struct pxa3xx_nand_platform_data *pdata;
1033 struct pxa3xx_nand_info *info;
1034 struct pxa3xx_nand_host *host;
1035 struct nand_chip *chip;
1036 struct mtd_info *mtd;
1037 struct resource *r;
1038 int ret, irq, cs;
1039
1040 pdata = pdev->dev.platform_data;
1041 info = kzalloc(sizeof(*info) + (sizeof(*mtd) +
1042 sizeof(*host)) * pdata->num_cs, GFP_KERNEL);
1043 if (!info) {
1044 dev_err(&pdev->dev, "failed to allocate memory\n");
1045 return -ENOMEM;
1046 }
1047
1048 info->pdev = pdev;
1049 for (cs = 0; cs < pdata->num_cs; cs++) {
1050 mtd = (struct mtd_info *)((unsigned int)&info[1] +
1051 (sizeof(*mtd) + sizeof(*host)) * cs);
1052 chip = (struct nand_chip *)(&mtd[1]);
1053 host = (struct pxa3xx_nand_host *)chip;
1054 info->host[cs] = host;
1055 host->mtd = mtd;
1056 host->cs = cs;
1057 host->info_data = info;
1058 mtd->priv = host;
1059 mtd->owner = THIS_MODULE;
1060
1061 chip->ecc.read_page = pxa3xx_nand_read_page_hwecc;
1062 chip->ecc.write_page = pxa3xx_nand_write_page_hwecc;
1063 chip->controller = &info->controller;
1064 chip->waitfunc = pxa3xx_nand_waitfunc;
1065 chip->select_chip = pxa3xx_nand_select_chip;
1066 chip->cmdfunc = pxa3xx_nand_cmdfunc;
1067 chip->read_word = pxa3xx_nand_read_word;
1068 chip->read_byte = pxa3xx_nand_read_byte;
1069 chip->read_buf = pxa3xx_nand_read_buf;
1070 chip->write_buf = pxa3xx_nand_write_buf;
1071 chip->verify_buf = pxa3xx_nand_verify_buf;
1072 }
1073
1074 spin_lock_init(&chip->controller->lock);
1075 init_waitqueue_head(&chip->controller->wq);
1076 info->clk = clk_get(&pdev->dev, NULL);
1077 if (IS_ERR(info->clk)) {
1078 dev_err(&pdev->dev, "failed to get nand clock\n");
1079 ret = PTR_ERR(info->clk);
1080 goto fail_free_mtd;
1081 }
1082 clk_enable(info->clk);
1083
1084 r = platform_get_resource(pdev, IORESOURCE_DMA, 0);
1085 if (r == NULL) {
1086 dev_err(&pdev->dev, "no resource defined for data DMA\n");
1087 ret = -ENXIO;
1088 goto fail_put_clk;
1089 }
1090 info->drcmr_dat = r->start;
1091
1092 r = platform_get_resource(pdev, IORESOURCE_DMA, 1);
1093 if (r == NULL) {
1094 dev_err(&pdev->dev, "no resource defined for command DMA\n");
1095 ret = -ENXIO;
1096 goto fail_put_clk;
1097 }
1098 info->drcmr_cmd = r->start;
1099
1100 irq = platform_get_irq(pdev, 0);
1101 if (irq < 0) {
1102 dev_err(&pdev->dev, "no IRQ resource defined\n");
1103 ret = -ENXIO;
1104 goto fail_put_clk;
1105 }
1106
1107 r = platform_get_resource(pdev, IORESOURCE_MEM, 0);
1108 if (r == NULL) {
1109 dev_err(&pdev->dev, "no IO memory resource defined\n");
1110 ret = -ENODEV;
1111 goto fail_put_clk;
1112 }
1113
1114 r = request_mem_region(r->start, resource_size(r), pdev->name);
1115 if (r == NULL) {
1116 dev_err(&pdev->dev, "failed to request memory resource\n");
1117 ret = -EBUSY;
1118 goto fail_put_clk;
1119 }
1120
1121 info->mmio_base = ioremap(r->start, resource_size(r));
1122 if (info->mmio_base == NULL) {
1123 dev_err(&pdev->dev, "ioremap() failed\n");
1124 ret = -ENODEV;
1125 goto fail_free_res;
1126 }
1127 info->mmio_phys = r->start;
1128
1129 ret = pxa3xx_nand_init_buff(info);
1130 if (ret)
1131 goto fail_free_io;
1132
1133 /* initialize all interrupts to be disabled */
1134 disable_int(info, NDSR_MASK);
1135
1136 ret = request_irq(irq, pxa3xx_nand_irq, IRQF_DISABLED,
1137 pdev->name, info);
1138 if (ret < 0) {
1139 dev_err(&pdev->dev, "failed to request IRQ\n");
1140 goto fail_free_buf;
1141 }
1142
1143 platform_set_drvdata(pdev, info);
1144
1145 return 0;
1146
1147 fail_free_buf:
1148 free_irq(irq, info);
1149 if (use_dma) {
1150 pxa_free_dma(info->data_dma_ch);
1151 dma_free_coherent(&pdev->dev, MAX_BUFF_SIZE,
1152 info->data_buff, info->data_buff_phys);
1153 } else
1154 kfree(info->data_buff);
1155 fail_free_io:
1156 iounmap(info->mmio_base);
1157 fail_free_res:
1158 release_mem_region(r->start, resource_size(r));
1159 fail_put_clk:
1160 clk_disable(info->clk);
1161 clk_put(info->clk);
1162 fail_free_mtd:
1163 kfree(info);
1164 return ret;
1165 }
1166
1167 static int pxa3xx_nand_remove(struct platform_device *pdev)
1168 {
1169 struct pxa3xx_nand_info *info = platform_get_drvdata(pdev);
1170 struct pxa3xx_nand_platform_data *pdata;
1171 struct resource *r;
1172 int irq, cs;
1173
1174 if (!info)
1175 return 0;
1176
1177 pdata = pdev->dev.platform_data;
1178 platform_set_drvdata(pdev, NULL);
1179
1180 irq = platform_get_irq(pdev, 0);
1181 if (irq >= 0)
1182 free_irq(irq, info);
1183 if (use_dma) {
1184 pxa_free_dma(info->data_dma_ch);
1185 dma_free_writecombine(&pdev->dev, MAX_BUFF_SIZE,
1186 info->data_buff, info->data_buff_phys);
1187 } else
1188 kfree(info->data_buff);
1189
1190 iounmap(info->mmio_base);
1191 r = platform_get_resource(pdev, IORESOURCE_MEM, 0);
1192 release_mem_region(r->start, resource_size(r));
1193
1194 clk_disable(info->clk);
1195 clk_put(info->clk);
1196
1197 for (cs = 0; cs < pdata->num_cs; cs++)
1198 nand_release(info->host[cs]->mtd);
1199 kfree(info);
1200 return 0;
1201 }
1202
1203 static int pxa3xx_nand_probe(struct platform_device *pdev)
1204 {
1205 struct pxa3xx_nand_platform_data *pdata;
1206 struct pxa3xx_nand_info *info;
1207 int ret, cs, probe_success;
1208
1209 pdata = pdev->dev.platform_data;
1210 if (!pdata) {
1211 dev_err(&pdev->dev, "no platform data defined\n");
1212 return -ENODEV;
1213 }
1214
1215 ret = alloc_nand_resource(pdev);
1216 if (ret) {
1217 dev_err(&pdev->dev, "alloc nand resource failed\n");
1218 return ret;
1219 }
1220
1221 info = platform_get_drvdata(pdev);
1222 probe_success = 0;
1223 for (cs = 0; cs < pdata->num_cs; cs++) {
1224 info->cs = cs;
1225 ret = pxa3xx_nand_scan(info->host[cs]->mtd);
1226 if (ret) {
1227 dev_warn(&pdev->dev, "failed to scan nand at cs %d\n",
1228 cs);
1229 continue;
1230 }
1231
1232 ret = mtd_device_parse_register(info->host[cs]->mtd, NULL,
1233 NULL, pdata->parts[cs],
1234 pdata->nr_parts[cs]);
1235 if (!ret)
1236 probe_success = 1;
1237 }
1238
1239 if (!probe_success) {
1240 pxa3xx_nand_remove(pdev);
1241 return -ENODEV;
1242 }
1243
1244 return 0;
1245 }
1246
1247 #ifdef CONFIG_PM
1248 static int pxa3xx_nand_suspend(struct platform_device *pdev, pm_message_t state)
1249 {
1250 struct pxa3xx_nand_info *info = platform_get_drvdata(pdev);
1251 struct pxa3xx_nand_platform_data *pdata;
1252 struct mtd_info *mtd;
1253 int cs;
1254
1255 pdata = pdev->dev.platform_data;
1256 if (info->state) {
1257 dev_err(&pdev->dev, "driver busy, state = %d\n", info->state);
1258 return -EAGAIN;
1259 }
1260
1261 for (cs = 0; cs < pdata->num_cs; cs++) {
1262 mtd = info->host[cs]->mtd;
1263 mtd_suspend(mtd);
1264 }
1265
1266 return 0;
1267 }
1268
1269 static int pxa3xx_nand_resume(struct platform_device *pdev)
1270 {
1271 struct pxa3xx_nand_info *info = platform_get_drvdata(pdev);
1272 struct pxa3xx_nand_platform_data *pdata;
1273 struct mtd_info *mtd;
1274 int cs;
1275
1276 pdata = pdev->dev.platform_data;
1277 /* We don't want to handle interrupt without calling mtd routine */
1278 disable_int(info, NDCR_INT_MASK);
1279
1280 /*
1281 * Directly set the chip select to a invalid value,
1282 * then the driver would reset the timing according
1283 * to current chip select at the beginning of cmdfunc
1284 */
1285 info->cs = 0xff;
1286
1287 /*
1288 * As the spec says, the NDSR would be updated to 0x1800 when
1289 * doing the nand_clk disable/enable.
1290 * To prevent it damaging state machine of the driver, clear
1291 * all status before resume
1292 */
1293 nand_writel(info, NDSR, NDSR_MASK);
1294 for (cs = 0; cs < pdata->num_cs; cs++) {
1295 mtd = info->host[cs]->mtd;
1296 mtd_resume(mtd);
1297 }
1298
1299 return 0;
1300 }
1301 #else
1302 #define pxa3xx_nand_suspend NULL
1303 #define pxa3xx_nand_resume NULL
1304 #endif
1305
1306 static struct platform_driver pxa3xx_nand_driver = {
1307 .driver = {
1308 .name = "pxa3xx-nand",
1309 },
1310 .probe = pxa3xx_nand_probe,
1311 .remove = pxa3xx_nand_remove,
1312 .suspend = pxa3xx_nand_suspend,
1313 .resume = pxa3xx_nand_resume,
1314 };
1315
1316 module_platform_driver(pxa3xx_nand_driver);
1317
1318 MODULE_LICENSE("GPL");
1319 MODULE_DESCRIPTION("PXA3xx NAND controller driver");
Linux with added FPC-III support