?  search:
summary | log | graphiclog1 | graphiclog2 | commit | commitdiff | tree | refs | edit | fork
blame | history | raw | HEAD
gpio: rcar: Fix runtime PM imbalance on error
[linux/fpc-iii.git] / drivers / media / rc / redrat3.c
blobaad9526f3754d4a94ea46522d0055b6a8596b886
1 // SPDX-License-Identifier: GPL-2.0-or-later
2 /*
3 * USB RedRat3 IR Transceiver rc-core driver
4 *
5 * Copyright (c) 2011 by Jarod Wilson <jarod@redhat.com>
6 * based heavily on the work of Stephen Cox, with additional
7 * help from RedRat Ltd.
8 *
9 * This driver began life based an an old version of the first-generation
10 * lirc_mceusb driver from the lirc 0.7.2 distribution. It was then
11 * significantly rewritten by Stephen Cox with the aid of RedRat Ltd's
12 * Chris Dodge.
13 *
14 * The driver was then ported to rc-core and significantly rewritten again,
15 * by Jarod, using the in-kernel mceusb driver as a guide, after an initial
16 * port effort was started by Stephen.
17 *
18 * TODO LIST:
19 * - fix lirc not showing repeats properly
20 * --
21 *
22 * The RedRat3 is a USB transceiver with both send & receive,
23 * with 2 separate sensors available for receive to enable
24 * both good long range reception for general use, and good
25 * short range reception when required for learning a signal.
26 *
27 * http://www.redrat.co.uk/
28 *
29 * It uses its own little protocol to communicate, the required
30 * parts of which are embedded within this driver.
31 * --
32 */
33
34 #include <asm/unaligned.h>
35 #include <linux/device.h>
36 #include <linux/leds.h>
37 #include <linux/module.h>
38 #include <linux/slab.h>
39 #include <linux/usb.h>
40 #include <linux/usb/input.h>
41 #include <media/rc-core.h>
42
43 /* Driver Information */
44 #define DRIVER_AUTHOR "Jarod Wilson <jarod@redhat.com>"
45 #define DRIVER_AUTHOR2 "The Dweller, Stephen Cox"
46 #define DRIVER_DESC "RedRat3 USB IR Transceiver Driver"
47 #define DRIVER_NAME "redrat3"
48
49 /* bulk data transfer types */
50 #define RR3_ERROR 0x01
51 #define RR3_MOD_SIGNAL_IN 0x20
52 #define RR3_MOD_SIGNAL_OUT 0x21
53
54 /* Get the RR firmware version */
55 #define RR3_FW_VERSION 0xb1
56 #define RR3_FW_VERSION_LEN 64
57 /* Send encoded signal bulk-sent earlier*/
58 #define RR3_TX_SEND_SIGNAL 0xb3
59 #define RR3_SET_IR_PARAM 0xb7
60 #define RR3_GET_IR_PARAM 0xb8
61 /* Blink the red LED on the device */
62 #define RR3_BLINK_LED 0xb9
63 /* Read serial number of device */
64 #define RR3_READ_SER_NO 0xba
65 #define RR3_SER_NO_LEN 4
66 /* Start capture with the RC receiver */
67 #define RR3_RC_DET_ENABLE 0xbb
68 /* Stop capture with the RC receiver */
69 #define RR3_RC_DET_DISABLE 0xbc
70 /* Start capture with the wideband receiver */
71 #define RR3_MODSIG_CAPTURE 0xb2
72 /* Return the status of RC detector capture */
73 #define RR3_RC_DET_STATUS 0xbd
74 /* Reset redrat */
75 #define RR3_RESET 0xa0
76
77 /* Max number of lengths in the signal. */
78 #define RR3_IR_IO_MAX_LENGTHS 0x01
79 /* Periods to measure mod. freq. */
80 #define RR3_IR_IO_PERIODS_MF 0x02
81 /* Size of memory for main signal data */
82 #define RR3_IR_IO_SIG_MEM_SIZE 0x03
83 /* Delta value when measuring lengths */
84 #define RR3_IR_IO_LENGTH_FUZZ 0x04
85 /* Timeout for end of signal detection */
86 #define RR3_IR_IO_SIG_TIMEOUT 0x05
87 /* Minimum value for pause recognition. */
88 #define RR3_IR_IO_MIN_PAUSE 0x06
89
90 /* Clock freq. of EZ-USB chip */
91 #define RR3_CLK 24000000
92 /* Clock periods per timer count */
93 #define RR3_CLK_PER_COUNT 12
94 /* (RR3_CLK / RR3_CLK_PER_COUNT) */
95 #define RR3_CLK_CONV_FACTOR 2000000
96 /* USB bulk-in wideband IR data endpoint address */
97 #define RR3_WIDE_IN_EP_ADDR 0x81
98 /* USB bulk-in narrowband IR data endpoint address */
99 #define RR3_NARROW_IN_EP_ADDR 0x82
100
101 /* Size of the fixed-length portion of the signal */
102 #define RR3_DRIVER_MAXLENS 255
103 #define RR3_MAX_SIG_SIZE 512
104 #define RR3_TIME_UNIT 50
105 #define RR3_END_OF_SIGNAL 0x7f
106 #define RR3_TX_TRAILER_LEN 2
107 #define RR3_RX_MIN_TIMEOUT 5
108 #define RR3_RX_MAX_TIMEOUT 2000
109
110 /* The 8051's CPUCS Register address */
111 #define RR3_CPUCS_REG_ADDR 0x7f92
112
113 #define USB_RR3USB_VENDOR_ID 0x112a
114 #define USB_RR3USB_PRODUCT_ID 0x0001
115 #define USB_RR3IIUSB_PRODUCT_ID 0x0005
116
117
118 /*
119 * The redrat3 encodes an IR signal as set of different lengths and a set
120 * of indices into those lengths. This sets how much two lengths must
121 * differ before they are considered distinct, the value is specified
122 * in microseconds.
123 * Default 5, value 0 to 127.
124 */
125 static int length_fuzz = 5;
126 module_param(length_fuzz, uint, 0644);
127 MODULE_PARM_DESC(length_fuzz, "Length Fuzz (0-127)");
128
129 /*
130 * When receiving a continuous ir stream (for example when a user is
131 * holding a button down on a remote), this specifies the minimum size
132 * of a space when the redrat3 sends a irdata packet to the host. Specified
133 * in milliseconds. Default value 18ms.
134 * The value can be between 2 and 30 inclusive.
135 */
136 static int minimum_pause = 18;
137 module_param(minimum_pause, uint, 0644);
138 MODULE_PARM_DESC(minimum_pause, "Minimum Pause in ms (2-30)");
139
140 /*
141 * The carrier frequency is measured during the first pulse of the IR
142 * signal. The larger the number of periods used To measure, the more
143 * accurate the result is likely to be, however some signals have short
144 * initial pulses, so in some case it may be necessary to reduce this value.
145 * Default 8, value 1 to 255.
146 */
147 static int periods_measure_carrier = 8;
148 module_param(periods_measure_carrier, uint, 0644);
149 MODULE_PARM_DESC(periods_measure_carrier, "Number of Periods to Measure Carrier (1-255)");
150
151
152 struct redrat3_header {
153 __be16 length;
154 __be16 transfer_type;
155 } __packed;
156
157 /* sending and receiving irdata */
158 struct redrat3_irdata {
159 struct redrat3_header header;
160 __be32 pause;
161 __be16 mod_freq_count;
162 __be16 num_periods;
163 __u8 max_lengths;
164 __u8 no_lengths;
165 __be16 max_sig_size;
166 __be16 sig_size;
167 __u8 no_repeats;
168 __be16 lens[RR3_DRIVER_MAXLENS]; /* not aligned */
169 __u8 sigdata[RR3_MAX_SIG_SIZE];
170 } __packed;
171
172 /* firmware errors */
173 struct redrat3_error {
174 struct redrat3_header header;
175 __be16 fw_error;
176 } __packed;
177
178 /* table of devices that work with this driver */
179 static const struct usb_device_id redrat3_dev_table[] = {
180 /* Original version of the RedRat3 */
181 {USB_DEVICE(USB_RR3USB_VENDOR_ID, USB_RR3USB_PRODUCT_ID)},
182 /* Second Version/release of the RedRat3 - RetRat3-II */
183 {USB_DEVICE(USB_RR3USB_VENDOR_ID, USB_RR3IIUSB_PRODUCT_ID)},
184 {} /* Terminating entry */
185 };
186
187 /* Structure to hold all of our device specific stuff */
188 struct redrat3_dev {
189 /* core device bits */
190 struct rc_dev *rc;
191 struct device *dev;
192
193 /* led control */
194 struct led_classdev led;
195 atomic_t flash;
196 struct usb_ctrlrequest flash_control;
197 struct urb *flash_urb;
198 u8 flash_in_buf;
199
200 /* learning */
201 bool wideband;
202 struct usb_ctrlrequest learn_control;
203 struct urb *learn_urb;
204 u8 learn_buf;
205
206 /* save off the usb device pointer */
207 struct usb_device *udev;
208
209 /* the receive endpoint */
210 struct usb_endpoint_descriptor *ep_narrow;
211 /* the buffer to receive data */
212 void *bulk_in_buf;
213 /* urb used to read ir data */
214 struct urb *narrow_urb;
215 struct urb *wide_urb;
216
217 /* the send endpoint */
218 struct usb_endpoint_descriptor *ep_out;
219
220 /* usb dma */
221 dma_addr_t dma_in;
222
223 /* Is the device currently transmitting?*/
224 bool transmitting;
225
226 /* store for current packet */
227 struct redrat3_irdata irdata;
228 u16 bytes_read;
229
230 u32 carrier;
231
232 char name[64];
233 char phys[64];
234 };
235
236 static void redrat3_dump_fw_error(struct redrat3_dev *rr3, int code)
237 {
238 if (!rr3->transmitting && (code != 0x40))
239 dev_info(rr3->dev, "fw error code 0x%02x: ", code);
240
241 switch (code) {
242 case 0x00:
243 pr_cont("No Error\n");
244 break;
245
246 /* Codes 0x20 through 0x2f are IR Firmware Errors */
247 case 0x20:
248 pr_cont("Initial signal pulse not long enough to measure carrier frequency\n");
249 break;
250 case 0x21:
251 pr_cont("Not enough length values allocated for signal\n");
252 break;
253 case 0x22:
254 pr_cont("Not enough memory allocated for signal data\n");
255 break;
256 case 0x23:
257 pr_cont("Too many signal repeats\n");
258 break;
259 case 0x28:
260 pr_cont("Insufficient memory available for IR signal data memory allocation\n");
261 break;
262 case 0x29:
263 pr_cont("Insufficient memory available for IrDa signal data memory allocation\n");
264 break;
265
266 /* Codes 0x30 through 0x3f are USB Firmware Errors */
267 case 0x30:
268 pr_cont("Insufficient memory available for bulk transfer structure\n");
269 break;
270
271 /*
272 * Other error codes... These are primarily errors that can occur in
273 * the control messages sent to the redrat
274 */
275 case 0x40:
276 if (!rr3->transmitting)
277 pr_cont("Signal capture has been terminated\n");
278 break;
279 case 0x41:
280 pr_cont("Attempt to set/get and unknown signal I/O algorithm parameter\n");
281 break;
282 case 0x42:
283 pr_cont("Signal capture already started\n");
284 break;
285
286 default:
287 pr_cont("Unknown Error\n");
288 break;
289 }
290 }
291
292 static u32 redrat3_val_to_mod_freq(struct redrat3_irdata *irdata)
293 {
294 u32 mod_freq = 0;
295 u16 mod_freq_count = be16_to_cpu(irdata->mod_freq_count);
296
297 if (mod_freq_count != 0)
298 mod_freq = (RR3_CLK * be16_to_cpu(irdata->num_periods)) /
299 (mod_freq_count * RR3_CLK_PER_COUNT);
300
301 return mod_freq;
302 }
303
304 /* this function scales down the figures for the same result... */
305 static u32 redrat3_len_to_us(u32 length)
306 {
307 u32 biglen = length * 1000;
308 u32 divisor = (RR3_CLK_CONV_FACTOR) / 1000;
309 u32 result = (u32) (biglen / divisor);
310
311 /* don't allow zero lengths to go back, breaks lirc */
312 return result ? result : 1;
313 }
314
315 /*
316 * convert us back into redrat3 lengths
317 *
318 * length * 1000 length * 1000000
319 * ------------- = ---------------- = micro
320 * rr3clk / 1000 rr3clk
321
322 * 6 * 2 4 * 3 micro * rr3clk micro * rr3clk / 1000
323 * ----- = 4 ----- = 6 -------------- = len ---------------------
324 * 3 2 1000000 1000
325 */
326 static u32 redrat3_us_to_len(u32 microsec)
327 {
328 u32 result;
329 u32 divisor;
330
331 microsec = (microsec > IR_MAX_DURATION) ? IR_MAX_DURATION : microsec;
332 divisor = (RR3_CLK_CONV_FACTOR / 1000);
333 result = (u32)(microsec * divisor) / 1000;
334
335 /* don't allow zero lengths to go back, breaks lirc */
336 return result ? result : 1;
337 }
338
339 static void redrat3_process_ir_data(struct redrat3_dev *rr3)
340 {
341 struct ir_raw_event rawir = {};
342 struct device *dev;
343 unsigned int i, sig_size, single_len, offset, val;
344 u32 mod_freq;
345
346 dev = rr3->dev;
347
348 mod_freq = redrat3_val_to_mod_freq(&rr3->irdata);
349 dev_dbg(dev, "Got mod_freq of %u\n", mod_freq);
350 if (mod_freq && rr3->wideband) {
351 struct ir_raw_event ev = {
352 .carrier_report = 1,
353 .carrier = mod_freq
354 };
355
356 ir_raw_event_store(rr3->rc, &ev);
357 }
358
359 /* process each rr3 encoded byte into an int */
360 sig_size = be16_to_cpu(rr3->irdata.sig_size);
361 for (i = 0; i < sig_size; i++) {
362 offset = rr3->irdata.sigdata[i];
363 val = get_unaligned_be16(&rr3->irdata.lens[offset]);
364 single_len = redrat3_len_to_us(val);
365
366 /* we should always get pulse/space/pulse/space samples */
367 if (i % 2)
368 rawir.pulse = false;
369 else
370 rawir.pulse = true;
371
372 rawir.duration = US_TO_NS(single_len);
373 /* cap the value to IR_MAX_DURATION */
374 rawir.duration = (rawir.duration > IR_MAX_DURATION) ?
375 IR_MAX_DURATION : rawir.duration;
376
377 dev_dbg(dev, "storing %s with duration %d (i: %d)\n",
378 rawir.pulse ? "pulse" : "space", rawir.duration, i);
379 ir_raw_event_store_with_filter(rr3->rc, &rawir);
380 }
381
382 /* add a trailing space */
383 rawir.pulse = false;
384 rawir.timeout = true;
385 rawir.duration = rr3->rc->timeout;
386 dev_dbg(dev, "storing trailing timeout with duration %d\n",
387 rawir.duration);
388 ir_raw_event_store_with_filter(rr3->rc, &rawir);
389
390 dev_dbg(dev, "calling ir_raw_event_handle\n");
391 ir_raw_event_handle(rr3->rc);
392 }
393
394 /* Util fn to send rr3 cmds */
395 static int redrat3_send_cmd(int cmd, struct redrat3_dev *rr3)
396 {
397 struct usb_device *udev;
398 u8 *data;
399 int res;
400
401 data = kzalloc(sizeof(u8), GFP_KERNEL);
402 if (!data)
403 return -ENOMEM;
404
405 udev = rr3->udev;
406 res = usb_control_msg(udev, usb_rcvctrlpipe(udev, 0), cmd,
407 USB_TYPE_VENDOR | USB_RECIP_DEVICE | USB_DIR_IN,
408 0x0000, 0x0000, data, sizeof(u8), HZ * 10);
409
410 if (res < 0) {
411 dev_err(rr3->dev, "%s: Error sending rr3 cmd res %d, data %d",
412 __func__, res, *data);
413 res = -EIO;
414 } else
415 res = data[0];
416
417 kfree(data);
418
419 return res;
420 }
421
422 /* Enables the long range detector and starts async receive */
423 static int redrat3_enable_detector(struct redrat3_dev *rr3)
424 {
425 struct device *dev = rr3->dev;
426 u8 ret;
427
428 ret = redrat3_send_cmd(RR3_RC_DET_ENABLE, rr3);
429 if (ret != 0)
430 dev_dbg(dev, "%s: unexpected ret of %d\n",
431 __func__, ret);
432
433 ret = redrat3_send_cmd(RR3_RC_DET_STATUS, rr3);
434 if (ret != 1) {
435 dev_err(dev, "%s: detector status: %d, should be 1\n",
436 __func__, ret);
437 return -EIO;
438 }
439
440 ret = usb_submit_urb(rr3->narrow_urb, GFP_KERNEL);
441 if (ret) {
442 dev_err(rr3->dev, "narrow band urb failed: %d", ret);
443 return ret;
444 }
445
446 ret = usb_submit_urb(rr3->wide_urb, GFP_KERNEL);
447 if (ret)
448 dev_err(rr3->dev, "wide band urb failed: %d", ret);
449
450 return ret;
451 }
452
453 static inline void redrat3_delete(struct redrat3_dev *rr3,
454 struct usb_device *udev)
455 {
456 usb_kill_urb(rr3->narrow_urb);
457 usb_kill_urb(rr3->wide_urb);
458 usb_kill_urb(rr3->flash_urb);
459 usb_kill_urb(rr3->learn_urb);
460 usb_free_urb(rr3->narrow_urb);
461 usb_free_urb(rr3->wide_urb);
462 usb_free_urb(rr3->flash_urb);
463 usb_free_urb(rr3->learn_urb);
464 usb_free_coherent(udev, le16_to_cpu(rr3->ep_narrow->wMaxPacketSize),
465 rr3->bulk_in_buf, rr3->dma_in);
466
467 kfree(rr3);
468 }
469
470 static u32 redrat3_get_timeout(struct redrat3_dev *rr3)
471 {
472 __be32 *tmp;
473 u32 timeout = MS_TO_US(150); /* a sane default, if things go haywire */
474 int len, ret, pipe;
475
476 len = sizeof(*tmp);
477 tmp = kzalloc(len, GFP_KERNEL);
478 if (!tmp)
479 return timeout;
480
481 pipe = usb_rcvctrlpipe(rr3->udev, 0);
482 ret = usb_control_msg(rr3->udev, pipe, RR3_GET_IR_PARAM,
483 USB_TYPE_VENDOR | USB_RECIP_DEVICE | USB_DIR_IN,
484 RR3_IR_IO_SIG_TIMEOUT, 0, tmp, len, HZ * 5);
485 if (ret != len)
486 dev_warn(rr3->dev, "Failed to read timeout from hardware\n");
487 else {
488 timeout = redrat3_len_to_us(be32_to_cpup(tmp));
489
490 dev_dbg(rr3->dev, "Got timeout of %d ms\n", timeout / 1000);
491 }
492
493 kfree(tmp);
494
495 return timeout;
496 }
497
498 static int redrat3_set_timeout(struct rc_dev *rc_dev, unsigned int timeoutns)
499 {
500 struct redrat3_dev *rr3 = rc_dev->priv;
501 struct usb_device *udev = rr3->udev;
502 struct device *dev = rr3->dev;
503 __be32 *timeout;
504 int ret;
505
506 timeout = kmalloc(sizeof(*timeout), GFP_KERNEL);
507 if (!timeout)
508 return -ENOMEM;
509
510 *timeout = cpu_to_be32(redrat3_us_to_len(timeoutns / 1000));
511 ret = usb_control_msg(udev, usb_sndctrlpipe(udev, 0), RR3_SET_IR_PARAM,
512 USB_TYPE_VENDOR | USB_RECIP_DEVICE | USB_DIR_OUT,
513 RR3_IR_IO_SIG_TIMEOUT, 0, timeout, sizeof(*timeout),
514 HZ * 25);
515 dev_dbg(dev, "set ir parm timeout %d ret 0x%02x\n",
516 be32_to_cpu(*timeout), ret);
517
518 if (ret == sizeof(*timeout))
519 ret = 0;
520 else if (ret >= 0)
521 ret = -EIO;
522
523 kfree(timeout);
524
525 return ret;
526 }
527
528 static void redrat3_reset(struct redrat3_dev *rr3)
529 {
530 struct usb_device *udev = rr3->udev;
531 struct device *dev = rr3->dev;
532 int rc, rxpipe, txpipe;
533 u8 *val;
534 size_t const len = sizeof(*val);
535
536 rxpipe = usb_rcvctrlpipe(udev, 0);
537 txpipe = usb_sndctrlpipe(udev, 0);
538
539 val = kmalloc(len, GFP_KERNEL);
540 if (!val)
541 return;
542
543 *val = 0x01;
544 rc = usb_control_msg(udev, rxpipe, RR3_RESET,
545 USB_TYPE_VENDOR | USB_RECIP_DEVICE | USB_DIR_IN,
546 RR3_CPUCS_REG_ADDR, 0, val, len, HZ * 25);
547 dev_dbg(dev, "reset returned 0x%02x\n", rc);
548
549 *val = length_fuzz;
550 rc = usb_control_msg(udev, txpipe, RR3_SET_IR_PARAM,
551 USB_TYPE_VENDOR | USB_RECIP_DEVICE | USB_DIR_OUT,
552 RR3_IR_IO_LENGTH_FUZZ, 0, val, len, HZ * 25);
553 dev_dbg(dev, "set ir parm len fuzz %d rc 0x%02x\n", *val, rc);
554
555 *val = (65536 - (minimum_pause * 2000)) / 256;
556 rc = usb_control_msg(udev, txpipe, RR3_SET_IR_PARAM,
557 USB_TYPE_VENDOR | USB_RECIP_DEVICE | USB_DIR_OUT,
558 RR3_IR_IO_MIN_PAUSE, 0, val, len, HZ * 25);
559 dev_dbg(dev, "set ir parm min pause %d rc 0x%02x\n", *val, rc);
560
561 *val = periods_measure_carrier;
562 rc = usb_control_msg(udev, txpipe, RR3_SET_IR_PARAM,
563 USB_TYPE_VENDOR | USB_RECIP_DEVICE | USB_DIR_OUT,
564 RR3_IR_IO_PERIODS_MF, 0, val, len, HZ * 25);
565 dev_dbg(dev, "set ir parm periods measure carrier %d rc 0x%02x", *val,
566 rc);
567
568 *val = RR3_DRIVER_MAXLENS;
569 rc = usb_control_msg(udev, txpipe, RR3_SET_IR_PARAM,
570 USB_TYPE_VENDOR | USB_RECIP_DEVICE | USB_DIR_OUT,
571 RR3_IR_IO_MAX_LENGTHS, 0, val, len, HZ * 25);
572 dev_dbg(dev, "set ir parm max lens %d rc 0x%02x\n", *val, rc);
573
574 kfree(val);
575 }
576
577 static void redrat3_get_firmware_rev(struct redrat3_dev *rr3)
578 {
579 int rc;
580 char *buffer;
581
582 buffer = kcalloc(RR3_FW_VERSION_LEN + 1, sizeof(*buffer), GFP_KERNEL);
583 if (!buffer)
584 return;
585
586 rc = usb_control_msg(rr3->udev, usb_rcvctrlpipe(rr3->udev, 0),
587 RR3_FW_VERSION,
588 USB_TYPE_VENDOR | USB_RECIP_DEVICE | USB_DIR_IN,
589 0, 0, buffer, RR3_FW_VERSION_LEN, HZ * 5);
590
591 if (rc >= 0)
592 dev_info(rr3->dev, "Firmware rev: %s", buffer);
593 else
594 dev_err(rr3->dev, "Problem fetching firmware ID\n");
595
596 kfree(buffer);
597 }
598
599 static void redrat3_read_packet_start(struct redrat3_dev *rr3, unsigned len)
600 {
601 struct redrat3_header *header = rr3->bulk_in_buf;
602 unsigned pktlen, pkttype;
603
604 /* grab the Length and type of transfer */
605 pktlen = be16_to_cpu(header->length);
606 pkttype = be16_to_cpu(header->transfer_type);
607
608 if (pktlen > sizeof(rr3->irdata)) {
609 dev_warn(rr3->dev, "packet length %u too large\n", pktlen);
610 return;
611 }
612
613 switch (pkttype) {
614 case RR3_ERROR:
615 if (len >= sizeof(struct redrat3_error)) {
616 struct redrat3_error *error = rr3->bulk_in_buf;
617 unsigned fw_error = be16_to_cpu(error->fw_error);
618 redrat3_dump_fw_error(rr3, fw_error);
619 }
620 break;
621
622 case RR3_MOD_SIGNAL_IN:
623 memcpy(&rr3->irdata, rr3->bulk_in_buf, len);
624 rr3->bytes_read = len;
625 dev_dbg(rr3->dev, "bytes_read %d, pktlen %d\n",
626 rr3->bytes_read, pktlen);
627 break;
628
629 default:
630 dev_dbg(rr3->dev, "ignoring packet with type 0x%02x, len of %d, 0x%02x\n",
631 pkttype, len, pktlen);
632 break;
633 }
634 }
635
636 static void redrat3_read_packet_continue(struct redrat3_dev *rr3, unsigned len)
637 {
638 void *irdata = &rr3->irdata;
639
640 if (len + rr3->bytes_read > sizeof(rr3->irdata)) {
641 dev_warn(rr3->dev, "too much data for packet\n");
642 rr3->bytes_read = 0;
643 return;
644 }
645
646 memcpy(irdata + rr3->bytes_read, rr3->bulk_in_buf, len);
647
648 rr3->bytes_read += len;
649 dev_dbg(rr3->dev, "bytes_read %d, pktlen %d\n", rr3->bytes_read,
650 be16_to_cpu(rr3->irdata.header.length));
651 }
652
653 /* gather IR data from incoming urb, process it when we have enough */
654 static int redrat3_get_ir_data(struct redrat3_dev *rr3, unsigned len)
655 {
656 struct device *dev = rr3->dev;
657 unsigned pkttype;
658 int ret = 0;
659
660 if (rr3->bytes_read == 0 && len >= sizeof(struct redrat3_header)) {
661 redrat3_read_packet_start(rr3, len);
662 } else if (rr3->bytes_read != 0) {
663 redrat3_read_packet_continue(rr3, len);
664 } else if (rr3->bytes_read == 0) {
665 dev_err(dev, "error: no packet data read\n");
666 ret = -ENODATA;
667 goto out;
668 }
669
670 if (rr3->bytes_read < be16_to_cpu(rr3->irdata.header.length) +
671 sizeof(struct redrat3_header))
672 /* we're still accumulating data */
673 return 0;
674
675 /* if we get here, we've got IR data to decode */
676 pkttype = be16_to_cpu(rr3->irdata.header.transfer_type);
677 if (pkttype == RR3_MOD_SIGNAL_IN)
678 redrat3_process_ir_data(rr3);
679 else
680 dev_dbg(dev, "discarding non-signal data packet (type 0x%02x)\n",
681 pkttype);
682
683 out:
684 rr3->bytes_read = 0;
685 return ret;
686 }
687
688 /* callback function from USB when async USB request has completed */
689 static void redrat3_handle_async(struct urb *urb)
690 {
691 struct redrat3_dev *rr3 = urb->context;
692 int ret;
693
694 switch (urb->status) {
695 case 0:
696 ret = redrat3_get_ir_data(rr3, urb->actual_length);
697 if (!ret && rr3->wideband && !rr3->learn_urb->hcpriv) {
698 ret = usb_submit_urb(rr3->learn_urb, GFP_ATOMIC);
699 if (ret)
700 dev_err(rr3->dev, "Failed to submit learning urb: %d",
701 ret);
702 }
703
704 if (!ret) {
705 /* no error, prepare to read more */
706 ret = usb_submit_urb(urb, GFP_ATOMIC);
707 if (ret)
708 dev_err(rr3->dev, "Failed to resubmit urb: %d",
709 ret);
710 }
711 break;
712
713 case -ECONNRESET:
714 case -ENOENT:
715 case -ESHUTDOWN:
716 usb_unlink_urb(urb);
717 return;
718
719 case -EPIPE:
720 default:
721 dev_warn(rr3->dev, "Error: urb status = %d\n", urb->status);
722 rr3->bytes_read = 0;
723 break;
724 }
725 }
726
727 static u16 mod_freq_to_val(unsigned int mod_freq)
728 {
729 int mult = 6000000;
730
731 /* Clk used in mod. freq. generation is CLK24/4. */
732 return 65536 - (mult / mod_freq);
733 }
734
735 static int redrat3_set_tx_carrier(struct rc_dev *rcdev, u32 carrier)
736 {
737 struct redrat3_dev *rr3 = rcdev->priv;
738 struct device *dev = rr3->dev;
739
740 dev_dbg(dev, "Setting modulation frequency to %u", carrier);
741 if (carrier == 0)
742 return -EINVAL;
743
744 rr3->carrier = carrier;
745
746 return 0;
747 }
748
749 static int redrat3_transmit_ir(struct rc_dev *rcdev, unsigned *txbuf,
750 unsigned count)
751 {
752 struct redrat3_dev *rr3 = rcdev->priv;
753 struct device *dev = rr3->dev;
754 struct redrat3_irdata *irdata = NULL;
755 int ret, ret_len;
756 int lencheck, cur_sample_len, pipe;
757 int *sample_lens = NULL;
758 u8 curlencheck = 0;
759 unsigned i, sendbuf_len;
760
761 if (rr3->transmitting) {
762 dev_warn(dev, "%s: transmitter already in use\n", __func__);
763 return -EAGAIN;
764 }
765
766 if (count > RR3_MAX_SIG_SIZE - RR3_TX_TRAILER_LEN)
767 return -EINVAL;
768
769 /* rr3 will disable rc detector on transmit */
770 rr3->transmitting = true;
771
772 sample_lens = kcalloc(RR3_DRIVER_MAXLENS,
773 sizeof(*sample_lens),
774 GFP_KERNEL);
775 if (!sample_lens)
776 return -ENOMEM;
777
778 irdata = kzalloc(sizeof(*irdata), GFP_KERNEL);
779 if (!irdata) {
780 ret = -ENOMEM;
781 goto out;
782 }
783
784 for (i = 0; i < count; i++) {
785 cur_sample_len = redrat3_us_to_len(txbuf[i]);
786 if (cur_sample_len > 0xffff) {
787 dev_warn(dev, "transmit period of %uus truncated to %uus\n",
788 txbuf[i], redrat3_len_to_us(0xffff));
789 cur_sample_len = 0xffff;
790 }
791 for (lencheck = 0; lencheck < curlencheck; lencheck++) {
792 if (sample_lens[lencheck] == cur_sample_len)
793 break;
794 }
795 if (lencheck == curlencheck) {
796 dev_dbg(dev, "txbuf[%d]=%u, pos %d, enc %u\n",
797 i, txbuf[i], curlencheck, cur_sample_len);
798 if (curlencheck < RR3_DRIVER_MAXLENS) {
799 /* now convert the value to a proper
800 * rr3 value.. */
801 sample_lens[curlencheck] = cur_sample_len;
802 put_unaligned_be16(cur_sample_len,
803 &irdata->lens[curlencheck]);
804 curlencheck++;
805 } else {
806 ret = -EINVAL;
807 goto out;
808 }
809 }
810 irdata->sigdata[i] = lencheck;
811 }
812
813 irdata->sigdata[count] = RR3_END_OF_SIGNAL;
814 irdata->sigdata[count + 1] = RR3_END_OF_SIGNAL;
815
816 sendbuf_len = offsetof(struct redrat3_irdata,
817 sigdata[count + RR3_TX_TRAILER_LEN]);
818 /* fill in our packet header */
819 irdata->header.length = cpu_to_be16(sendbuf_len -
820 sizeof(struct redrat3_header));
821 irdata->header.transfer_type = cpu_to_be16(RR3_MOD_SIGNAL_OUT);
822 irdata->pause = cpu_to_be32(redrat3_len_to_us(100));
823 irdata->mod_freq_count = cpu_to_be16(mod_freq_to_val(rr3->carrier));
824 irdata->no_lengths = curlencheck;
825 irdata->sig_size = cpu_to_be16(count + RR3_TX_TRAILER_LEN);
826
827 pipe = usb_sndbulkpipe(rr3->udev, rr3->ep_out->bEndpointAddress);
828 ret = usb_bulk_msg(rr3->udev, pipe, irdata,
829 sendbuf_len, &ret_len, 10 * HZ);
830 dev_dbg(dev, "sent %d bytes, (ret %d)\n", ret_len, ret);
831
832 /* now tell the hardware to transmit what we sent it */
833 pipe = usb_rcvctrlpipe(rr3->udev, 0);
834 ret = usb_control_msg(rr3->udev, pipe, RR3_TX_SEND_SIGNAL,
835 USB_TYPE_VENDOR | USB_RECIP_DEVICE | USB_DIR_IN,
836 0, 0, irdata, 2, HZ * 10);
837
838 if (ret < 0)
839 dev_err(dev, "Error: control msg send failed, rc %d\n", ret);
840 else
841 ret = count;
842
843 out:
844 kfree(irdata);
845 kfree(sample_lens);
846
847 rr3->transmitting = false;
848 /* rr3 re-enables rc detector because it was enabled before */
849
850 return ret;
851 }
852
853 static void redrat3_brightness_set(struct led_classdev *led_dev, enum
854 led_brightness brightness)
855 {
856 struct redrat3_dev *rr3 = container_of(led_dev, struct redrat3_dev,
857 led);
858
859 if (brightness != LED_OFF && atomic_cmpxchg(&rr3->flash, 0, 1) == 0) {
860 int ret = usb_submit_urb(rr3->flash_urb, GFP_ATOMIC);
861 if (ret != 0) {
862 dev_dbg(rr3->dev, "%s: unexpected ret of %d\n",
863 __func__, ret);
864 atomic_set(&rr3->flash, 0);
865 }
866 }
867 }
868
869 static int redrat3_wideband_receiver(struct rc_dev *rcdev, int enable)
870 {
871 struct redrat3_dev *rr3 = rcdev->priv;
872 int ret = 0;
873
874 rr3->wideband = enable != 0;
875
876 if (enable) {
877 ret = usb_submit_urb(rr3->learn_urb, GFP_KERNEL);
878 if (ret)
879 dev_err(rr3->dev, "Failed to submit learning urb: %d",
880 ret);
881 }
882
883 return ret;
884 }
885
886 static void redrat3_learn_complete(struct urb *urb)
887 {
888 struct redrat3_dev *rr3 = urb->context;
889
890 switch (urb->status) {
891 case 0:
892 break;
893 case -ECONNRESET:
894 case -ENOENT:
895 case -ESHUTDOWN:
896 usb_unlink_urb(urb);
897 return;
898 case -EPIPE:
899 default:
900 dev_err(rr3->dev, "Error: learn urb status = %d", urb->status);
901 break;
902 }
903 }
904
905 static void redrat3_led_complete(struct urb *urb)
906 {
907 struct redrat3_dev *rr3 = urb->context;
908
909 switch (urb->status) {
910 case 0:
911 break;
912 case -ECONNRESET:
913 case -ENOENT:
914 case -ESHUTDOWN:
915 usb_unlink_urb(urb);
916 return;
917 case -EPIPE:
918 default:
919 dev_dbg(rr3->dev, "Error: urb status = %d\n", urb->status);
920 break;
921 }
922
923 rr3->led.brightness = LED_OFF;
924 atomic_dec(&rr3->flash);
925 }
926
927 static struct rc_dev *redrat3_init_rc_dev(struct redrat3_dev *rr3)
928 {
929 struct device *dev = rr3->dev;
930 struct rc_dev *rc;
931 int ret;
932 u16 prod = le16_to_cpu(rr3->udev->descriptor.idProduct);
933
934 rc = rc_allocate_device(RC_DRIVER_IR_RAW);
935 if (!rc)
936 return NULL;
937
938 snprintf(rr3->name, sizeof(rr3->name),
939 "RedRat3%s Infrared Remote Transceiver",
940 prod == USB_RR3IIUSB_PRODUCT_ID ? "-II" : "");
941
942 usb_make_path(rr3->udev, rr3->phys, sizeof(rr3->phys));
943
944 rc->device_name = rr3->name;
945 rc->input_phys = rr3->phys;
946 usb_to_input_id(rr3->udev, &rc->input_id);
947 rc->dev.parent = dev;
948 rc->priv = rr3;
949 rc->allowed_protocols = RC_PROTO_BIT_ALL_IR_DECODER;
950 rc->min_timeout = MS_TO_NS(RR3_RX_MIN_TIMEOUT);
951 rc->max_timeout = MS_TO_NS(RR3_RX_MAX_TIMEOUT);
952 rc->timeout = US_TO_NS(redrat3_get_timeout(rr3));
953 rc->s_timeout = redrat3_set_timeout;
954 rc->tx_ir = redrat3_transmit_ir;
955 rc->s_tx_carrier = redrat3_set_tx_carrier;
956 rc->s_carrier_report = redrat3_wideband_receiver;
957 rc->driver_name = DRIVER_NAME;
958 rc->rx_resolution = US_TO_NS(2);
959 rc->map_name = RC_MAP_HAUPPAUGE;
960
961 ret = rc_register_device(rc);
962 if (ret < 0) {
963 dev_err(dev, "remote dev registration failed\n");
964 goto out;
965 }
966
967 return rc;
968
969 out:
970 rc_free_device(rc);
971 return NULL;
972 }
973
974 static int redrat3_dev_probe(struct usb_interface *intf,
975 const struct usb_device_id *id)
976 {
977 struct usb_device *udev = interface_to_usbdev(intf);
978 struct device *dev = &intf->dev;
979 struct usb_host_interface *uhi;
980 struct redrat3_dev *rr3;
981 struct usb_endpoint_descriptor *ep;
982 struct usb_endpoint_descriptor *ep_narrow = NULL;
983 struct usb_endpoint_descriptor *ep_wide = NULL;
984 struct usb_endpoint_descriptor *ep_out = NULL;
985 u8 addr, attrs;
986 int pipe, i;
987 int retval = -ENOMEM;
988
989 uhi = intf->cur_altsetting;
990
991 /* find our bulk-in and bulk-out endpoints */
992 for (i = 0; i < uhi->desc.bNumEndpoints; ++i) {
993 ep = &uhi->endpoint[i].desc;
994 addr = ep->bEndpointAddress;
995 attrs = ep->bmAttributes;
996
997 if (((addr & USB_ENDPOINT_DIR_MASK) == USB_DIR_IN) &&
998 ((attrs & USB_ENDPOINT_XFERTYPE_MASK) ==
999 USB_ENDPOINT_XFER_BULK)) {
1000 dev_dbg(dev, "found bulk-in endpoint at 0x%02x\n",
1001 ep->bEndpointAddress);
1002 /* data comes in on 0x82, 0x81 is for learning */
1003 if (ep->bEndpointAddress == RR3_NARROW_IN_EP_ADDR)
1004 ep_narrow = ep;
1005 if (ep->bEndpointAddress == RR3_WIDE_IN_EP_ADDR)
1006 ep_wide = ep;
1007 }
1008
1009 if ((ep_out == NULL) &&
1010 ((addr & USB_ENDPOINT_DIR_MASK) == USB_DIR_OUT) &&
1011 ((attrs & USB_ENDPOINT_XFERTYPE_MASK) ==
1012 USB_ENDPOINT_XFER_BULK)) {
1013 dev_dbg(dev, "found bulk-out endpoint at 0x%02x\n",
1014 ep->bEndpointAddress);
1015 ep_out = ep;
1016 }
1017 }
1018
1019 if (!ep_narrow || !ep_out || !ep_wide) {
1020 dev_err(dev, "Couldn't find all endpoints\n");
1021 retval = -ENODEV;
1022 goto no_endpoints;
1023 }
1024
1025 /* allocate memory for our device state and initialize it */
1026 rr3 = kzalloc(sizeof(*rr3), GFP_KERNEL);
1027 if (!rr3)
1028 goto no_endpoints;
1029
1030 rr3->dev = &intf->dev;
1031 rr3->ep_narrow = ep_narrow;
1032 rr3->ep_out = ep_out;
1033 rr3->udev = udev;
1034
1035 /* set up bulk-in endpoint */
1036 rr3->narrow_urb = usb_alloc_urb(0, GFP_KERNEL);
1037 if (!rr3->narrow_urb)
1038 goto redrat_free;
1039
1040 rr3->wide_urb = usb_alloc_urb(0, GFP_KERNEL);
1041 if (!rr3->wide_urb)
1042 goto redrat_free;
1043
1044 rr3->bulk_in_buf = usb_alloc_coherent(udev,
1045 le16_to_cpu(ep_narrow->wMaxPacketSize),
1046 GFP_KERNEL, &rr3->dma_in);
1047 if (!rr3->bulk_in_buf)
1048 goto redrat_free;
1049
1050 pipe = usb_rcvbulkpipe(udev, ep_narrow->bEndpointAddress);
1051 usb_fill_bulk_urb(rr3->narrow_urb, udev, pipe, rr3->bulk_in_buf,
1052 le16_to_cpu(ep_narrow->wMaxPacketSize),
1053 redrat3_handle_async, rr3);
1054 rr3->narrow_urb->transfer_dma = rr3->dma_in;
1055 rr3->narrow_urb->transfer_flags |= URB_NO_TRANSFER_DMA_MAP;
1056
1057 pipe = usb_rcvbulkpipe(udev, ep_wide->bEndpointAddress);
1058 usb_fill_bulk_urb(rr3->wide_urb, udev, pipe, rr3->bulk_in_buf,
1059 le16_to_cpu(ep_narrow->wMaxPacketSize),
1060 redrat3_handle_async, rr3);
1061 rr3->wide_urb->transfer_dma = rr3->dma_in;
1062 rr3->wide_urb->transfer_flags |= URB_NO_TRANSFER_DMA_MAP;
1063
1064 redrat3_reset(rr3);
1065 redrat3_get_firmware_rev(rr3);
1066
1067 /* default.. will get overridden by any sends with a freq defined */
1068 rr3->carrier = 38000;
1069
1070 atomic_set(&rr3->flash, 0);
1071 rr3->flash_urb = usb_alloc_urb(0, GFP_KERNEL);
1072 if (!rr3->flash_urb)
1073 goto redrat_free;
1074
1075 /* learn urb */
1076 rr3->learn_urb = usb_alloc_urb(0, GFP_KERNEL);
1077 if (!rr3->learn_urb)
1078 goto redrat_free;
1079
1080 /* setup packet is 'c0 b2 0000 0000 0001' */
1081 rr3->learn_control.bRequestType = 0xc0;
1082 rr3->learn_control.bRequest = RR3_MODSIG_CAPTURE;
1083 rr3->learn_control.wLength = cpu_to_le16(1);
1084
1085 usb_fill_control_urb(rr3->learn_urb, udev, usb_rcvctrlpipe(udev, 0),
1086 (unsigned char *)&rr3->learn_control,
1087 &rr3->learn_buf, sizeof(rr3->learn_buf),
1088 redrat3_learn_complete, rr3);
1089
1090 /* setup packet is 'c0 b9 0000 0000 0001' */
1091 rr3->flash_control.bRequestType = 0xc0;
1092 rr3->flash_control.bRequest = RR3_BLINK_LED;
1093 rr3->flash_control.wLength = cpu_to_le16(1);
1094
1095 usb_fill_control_urb(rr3->flash_urb, udev, usb_rcvctrlpipe(udev, 0),
1096 (unsigned char *)&rr3->flash_control,
1097 &rr3->flash_in_buf, sizeof(rr3->flash_in_buf),
1098 redrat3_led_complete, rr3);
1099
1100 /* led control */
1101 rr3->led.name = "redrat3:red:feedback";
1102 rr3->led.default_trigger = "rc-feedback";
1103 rr3->led.brightness_set = redrat3_brightness_set;
1104 retval = led_classdev_register(&intf->dev, &rr3->led);
1105 if (retval)
1106 goto redrat_free;
1107
1108 rr3->rc = redrat3_init_rc_dev(rr3);
1109 if (!rr3->rc) {
1110 retval = -ENOMEM;
1111 goto led_free;
1112 }
1113
1114 /* might be all we need to do? */
1115 retval = redrat3_enable_detector(rr3);
1116 if (retval < 0)
1117 goto led_free;
1118
1119 /* we can register the device now, as it is ready */
1120 usb_set_intfdata(intf, rr3);
1121
1122 return 0;
1123
1124 led_free:
1125 led_classdev_unregister(&rr3->led);
1126 redrat_free:
1127 redrat3_delete(rr3, rr3->udev);
1128
1129 no_endpoints:
1130 return retval;
1131 }
1132
1133 static void redrat3_dev_disconnect(struct usb_interface *intf)
1134 {
1135 struct usb_device *udev = interface_to_usbdev(intf);
1136 struct redrat3_dev *rr3 = usb_get_intfdata(intf);
1137
1138 usb_set_intfdata(intf, NULL);
1139 rc_unregister_device(rr3->rc);
1140 led_classdev_unregister(&rr3->led);
1141 redrat3_delete(rr3, udev);
1142 }
1143
1144 static int redrat3_dev_suspend(struct usb_interface *intf, pm_message_t message)
1145 {
1146 struct redrat3_dev *rr3 = usb_get_intfdata(intf);
1147
1148 led_classdev_suspend(&rr3->led);
1149 usb_kill_urb(rr3->narrow_urb);
1150 usb_kill_urb(rr3->wide_urb);
1151 usb_kill_urb(rr3->flash_urb);
1152 return 0;
1153 }
1154
1155 static int redrat3_dev_resume(struct usb_interface *intf)
1156 {
1157 struct redrat3_dev *rr3 = usb_get_intfdata(intf);
1158
1159 if (usb_submit_urb(rr3->narrow_urb, GFP_ATOMIC))
1160 return -EIO;
1161 if (usb_submit_urb(rr3->wide_urb, GFP_ATOMIC))
1162 return -EIO;
1163 led_classdev_resume(&rr3->led);
1164 return 0;
1165 }
1166
1167 static struct usb_driver redrat3_dev_driver = {
1168 .name = DRIVER_NAME,
1169 .probe = redrat3_dev_probe,
1170 .disconnect = redrat3_dev_disconnect,
1171 .suspend = redrat3_dev_suspend,
1172 .resume = redrat3_dev_resume,
1173 .reset_resume = redrat3_dev_resume,
1174 .id_table = redrat3_dev_table
1175 };
1176
1177 module_usb_driver(redrat3_dev_driver);
1178
1179 MODULE_DESCRIPTION(DRIVER_DESC);
1180 MODULE_AUTHOR(DRIVER_AUTHOR);
1181 MODULE_AUTHOR(DRIVER_AUTHOR2);
1182 MODULE_LICENSE("GPL");
1183 MODULE_DEVICE_TABLE(usb, redrat3_dev_table);
Linux with added FPC-III support