Documentation/devicetree/bindings/display/mxsfb.txt

   1 * Freescale MXS LCD Interface (LCDIF)
   2
   3 New bindings:
   4 =============
   5 Required properties:
   6 - compatible:   Should be "fsl,imx23-lcdif" for i.MX23.
   7                 Should be "fsl,imx28-lcdif" for i.MX28.
   8                 Should be "fsl,imx6sx-lcdif" for i.MX6SX.
   9 - reg:          Address and length of the register set for LCDIF
  10 - interrupts:   Should contain LCDIF interrupt
  11 - clocks:       A list of phandle + clock-specifier pairs, one for each
  12                 entry in 'clock-names'.
  13 - clock-names:  A list of clock names. For MXSFB it should contain:
  14     - "pix" for the LCDIF block clock
  15     - (MX6SX-only) "axi", "disp_axi" for the bus interface clock
  16
  17 Required sub-nodes:
  18   - port: The connection to an encoder chip.
  19
  20 Example:
  21
  22         lcdif1: display-controller@2220000 {
  23                 compatible = "fsl,imx6sx-lcdif", "fsl,imx28-lcdif";
  24                 reg = <0x02220000 0x4000>;
  25                 interrupts = <GIC_SPI 5 IRQ_TYPE_LEVEL_HIGH>;
  26                 clocks = <&clks IMX6SX_CLK_LCDIF1_PIX>,
  27                          <&clks IMX6SX_CLK_LCDIF_APB>,
  28                          <&clks IMX6SX_CLK_DISPLAY_AXI>;
  29                 clock-names = "pix", "axi", "disp_axi";
  30
  31                 port {
  32                         parallel_out: endpoint {
  33                                 remote-endpoint = <&panel_in_parallel>;
  34                         };
  35                 };
  36         };
  37
  38 Deprecated bindings:
  39 ====================
  40 Required properties:
  41 - compatible:   Should be "fsl,imx23-lcdif" for i.MX23.
  42                 Should be "fsl,imx28-lcdif" for i.MX28.
  43 - reg:          Address and length of the register set for LCDIF
  44 - interrupts:   Should contain LCDIF interrupts
  45 - display:      phandle to display node (see below for details)
  46
  47 * display node
  48
  49 Required properties:
  50 - bits-per-pixel:       <16> for RGB565, <32> for RGB888/666.
  51 - bus-width:            number of data lines.  Could be <8>, <16>, <18> or <24>.
  52
  53 Required sub-node:
  54 - display-timings:      Refer to binding doc display-timing.txt for details.
  55
  56 Examples:
  57
  58 lcdif@80030000 {
  59         compatible = "fsl,imx28-lcdif";
  60         reg = <0x80030000 2000>;
  61         interrupts = <38 86>;
  62
  63         display: display {
  64                 bits-per-pixel = <32>;
  65                 bus-width = <24>;
  66
  67                 display-timings {
  68                         native-mode = <&timing0>;
  69                         timing0: timing0 {
  70                                 clock-frequency = <33500000>;
  71                                 hactive = <800>;
  72                                 vactive = <480>;
  73                                 hfront-porch = <164>;
  74                                 hback-porch = <89>;
  75                                 hsync-len = <10>;
  76                                 vback-porch = <23>;
  77                                 vfront-porch = <10>;
  78                                 vsync-len = <10>;
  79                                 hsync-active = <0>;
  80                                 vsync-active = <0>;
  81                                 de-active = <1>;
  82                                 pixelclk-active = <0>;
  83                         };
  84                 };
  85         };
  86 };