xenbus_client.c: correct exit path for xenbus_map_ring_valloc_hvm

[linux/fpc-iii.git] / drivers / staging / wlan-ng / p80211netdev.c

/* src/p80211/p80211knetdev.c
*
* Linux Kernel net device interface
*
* Copyright (C) 1999 AbsoluteValue Systems, Inc.  All Rights Reserved.
* --------------------------------------------------------------------
*
* linux-wlan
*
*   The contents of this file are subject to the Mozilla Public
*   License Version 1.1 (the "License"); you may not use this file
*   except in compliance with the License. You may obtain a copy of
*   the License at http://www.mozilla.org/MPL/
*
*   Software distributed under the License is distributed on an "AS
*   IS" basis, WITHOUT WARRANTY OF ANY KIND, either express or
*   implied. See the License for the specific language governing
*   rights and limitations under the License.
*
*   Alternatively, the contents of this file may be used under the
*   terms of the GNU Public License version 2 (the "GPL"), in which
*   case the provisions of the GPL are applicable instead of the
*   above.  If you wish to allow the use of your version of this file
*   only under the terms of the GPL and not to allow others to use
*   your version of this file under the MPL, indicate your decision
*   by deleting the provisions above and replace them with the notice
*   and other provisions required by the GPL.  If you do not delete
*   the provisions above, a recipient may use your version of this
*   file under either the MPL or the GPL.
*
* --------------------------------------------------------------------
*
* Inquiries regarding the linux-wlan Open Source project can be
* made directly to:
*
* AbsoluteValue Systems Inc.
* info@linux-wlan.com
* http://www.linux-wlan.com
*
* --------------------------------------------------------------------
*
* Portions of the development of this software were funded by
* Intersil Corporation as part of PRISM(R) chipset product development.
*
* --------------------------------------------------------------------
*
* The functions required for a Linux network device are defined here.
*
* --------------------------------------------------------------------
*/

#include <linux/module.h>
#include <linux/kernel.h>
#include <linux/sched.h>
#include <linux/types.h>
#include <linux/skbuff.h>
#include <linux/slab.h>
#include <linux/proc_fs.h>
#include <linux/interrupt.h>
#include <linux/netdevice.h>
#include <linux/kmod.h>
#include <linux/if_arp.h>
#include <linux/wireless.h>
#include <linux/sockios.h>
#include <linux/etherdevice.h>
#include <linux/if_ether.h>
#include <linux/byteorder/generic.h>
#include <linux/bitops.h>
#include <linux/uaccess.h>
#include <asm/byteorder.h>

#ifdef SIOCETHTOOL
#include <linux/ethtool.h>
#endif

#include <net/iw_handler.h>
#include <net/net_namespace.h>
#include <net/cfg80211.h>

#include "p80211types.h"
#include "p80211hdr.h"
#include "p80211conv.h"
#include "p80211mgmt.h"
#include "p80211msg.h"
#include "p80211netdev.h"
#include "p80211ioctl.h"
#include "p80211req.h"
#include "p80211metastruct.h"
#include "p80211metadef.h"

#include "cfg80211.c"

/* Support functions */
static void p80211netdev_rx_bh(unsigned long arg);

/* netdevice method functions */
static int p80211knetdev_init(netdevice_t *netdev);
static struct net_device_stats *p80211knetdev_get_stats(netdevice_t *netdev);
static int p80211knetdev_open(netdevice_t *netdev);
static int p80211knetdev_stop(netdevice_t *netdev);
static int p80211knetdev_hard_start_xmit(struct sk_buff *skb,
                                         netdevice_t *netdev);
static void p80211knetdev_set_multicast_list(netdevice_t *dev);
static int p80211knetdev_do_ioctl(netdevice_t *dev, struct ifreq *ifr,
                                  int cmd);
static int p80211knetdev_set_mac_address(netdevice_t *dev, void *addr);
static void p80211knetdev_tx_timeout(netdevice_t *netdev);
static int p80211_rx_typedrop(wlandevice_t *wlandev, u16 fc);

int wlan_watchdog = 5000;
module_param(wlan_watchdog, int, 0644);
MODULE_PARM_DESC(wlan_watchdog, "transmit timeout in milliseconds");

int wlan_wext_write = 1;
module_param(wlan_wext_write, int, 0644);
MODULE_PARM_DESC(wlan_wext_write, "enable write wireless extensions");

/*----------------------------------------------------------------
* p80211knetdev_init
*
* Init method for a Linux netdevice.  Called in response to
* register_netdev.
*
* Arguments:
*       none
*
* Returns:
*       nothing
----------------------------------------------------------------*/
static int p80211knetdev_init(netdevice_t *netdev)
{
        /* Called in response to register_netdev */
        /* This is usually the probe function, but the probe has */
        /* already been done by the MSD and the create_kdev */
        /* function.  All we do here is return success */
        return 0;
}

/*----------------------------------------------------------------
* p80211knetdev_get_stats
*
* Statistics retrieval for linux netdevices.  Here we're reporting
* the Linux i/f level statistics.  Hence, for the primary numbers,
* we don't want to report the numbers from the MIB.  Eventually,
* it might be useful to collect some of the error counters though.
*
* Arguments:
*       netdev          Linux netdevice
*
* Returns:
*       the address of the statistics structure
----------------------------------------------------------------*/
static struct net_device_stats *p80211knetdev_get_stats(netdevice_t *netdev)
{
        wlandevice_t *wlandev = netdev->ml_priv;

        /* TODO: review the MIB stats for items that correspond to
           linux stats */

        return &(wlandev->linux_stats);
}

/*----------------------------------------------------------------
* p80211knetdev_open
*
* Linux netdevice open method.  Following a successful call here,
* the device is supposed to be ready for tx and rx.  In our
* situation that may not be entirely true due to the state of the
* MAC below.
*
* Arguments:
*       netdev          Linux network device structure
*
* Returns:
*       zero on success, non-zero otherwise
----------------------------------------------------------------*/
static int p80211knetdev_open(netdevice_t *netdev)
{
        int result = 0;         /* success */
        wlandevice_t *wlandev = netdev->ml_priv;

        /* Check to make sure the MSD is running */
        if (wlandev->msdstate != WLAN_MSD_RUNNING)
                return -ENODEV;

        /* Tell the MSD to open */
        if (wlandev->open != NULL) {
                result = wlandev->open(wlandev);
                if (result == 0) {
                        netif_start_queue(wlandev->netdev);
                        wlandev->state = WLAN_DEVICE_OPEN;
                }
        } else {
                result = -EAGAIN;
        }

        return result;
}

/*----------------------------------------------------------------
* p80211knetdev_stop
*
* Linux netdevice stop (close) method.  Following this call,
* no frames should go up or down through this interface.
*
* Arguments:
*       netdev          Linux network device structure
*
* Returns:
*       zero on success, non-zero otherwise
----------------------------------------------------------------*/
static int p80211knetdev_stop(netdevice_t *netdev)
{
        int result = 0;
        wlandevice_t *wlandev = netdev->ml_priv;

        if (wlandev->close != NULL)
                result = wlandev->close(wlandev);

        netif_stop_queue(wlandev->netdev);
        wlandev->state = WLAN_DEVICE_CLOSED;

        return result;
}

/*----------------------------------------------------------------
* p80211netdev_rx
*
* Frame receive function called by the mac specific driver.
*
* Arguments:
*       wlandev         WLAN network device structure
*       skb             skbuff containing a full 802.11 frame.
* Returns:
*       nothing
* Side effects:
*
----------------------------------------------------------------*/
void p80211netdev_rx(wlandevice_t *wlandev, struct sk_buff *skb)
{
        /* Enqueue for post-irq processing */
        skb_queue_tail(&wlandev->nsd_rxq, skb);
        tasklet_schedule(&wlandev->rx_bh);
}

/*----------------------------------------------------------------
* p80211netdev_rx_bh
*
* Deferred processing of all received frames.
*
* Arguments:
*       wlandev         WLAN network device structure
*       skb             skbuff containing a full 802.11 frame.
* Returns:
*       nothing
* Side effects:
*
----------------------------------------------------------------*/
static void p80211netdev_rx_bh(unsigned long arg)
{
        wlandevice_t *wlandev = (wlandevice_t *) arg;
        struct sk_buff *skb = NULL;
        netdevice_t *dev = wlandev->netdev;
        struct p80211_hdr_a3 *hdr;
        u16 fc;

        /* Let's empty our our queue */
        while ((skb = skb_dequeue(&wlandev->nsd_rxq))) {
                if (wlandev->state == WLAN_DEVICE_OPEN) {

                        if (dev->type != ARPHRD_ETHER) {
                                /* RAW frame; we shouldn't convert it */
                                /* XXX Append the Prism Header here instead. */

                                /* set up various data fields */
                                skb->dev = dev;
                                skb_reset_mac_header(skb);
                                skb->ip_summed = CHECKSUM_NONE;
                                skb->pkt_type = PACKET_OTHERHOST;
                                skb->protocol = htons(ETH_P_80211_RAW);
                                dev->last_rx = jiffies;

                                wlandev->linux_stats.rx_packets++;
                                wlandev->linux_stats.rx_bytes += skb->len;
                                netif_rx_ni(skb);
                                continue;
                        } else {
                                hdr = (struct p80211_hdr_a3 *) skb->data;
                                fc = le16_to_cpu(hdr->fc);
                                if (p80211_rx_typedrop(wlandev, fc)) {
                                        dev_kfree_skb(skb);
                                        continue;
                                }

                                /* perform mcast filtering */
                                if (wlandev->netdev->flags & IFF_ALLMULTI) {
                                        /* allow my local address through */
                                        if (memcmp
                                            (hdr->a1, wlandev->netdev->dev_addr,
                                             ETH_ALEN) != 0) {
                                                /* but reject anything else that
                                                   isn't multicast */
                                                if (!(hdr->a1[0] & 0x01)) {
                                                        dev_kfree_skb(skb);
                                                        continue;
                                                }
                                        }
                                }

                                if (skb_p80211_to_ether
                                    (wlandev, wlandev->ethconv, skb) == 0) {
                                        skb->dev->last_rx = jiffies;
                                        wlandev->linux_stats.rx_packets++;
                                        wlandev->linux_stats.rx_bytes +=
                                            skb->len;
                                        netif_rx_ni(skb);
                                        continue;
                                }
                                pr_debug("p80211_to_ether failed.\n");
                        }
                }
                dev_kfree_skb(skb);
        }
}

/*----------------------------------------------------------------
* p80211knetdev_hard_start_xmit
*
* Linux netdevice method for transmitting a frame.
*
* Arguments:
*       skb     Linux sk_buff containing the frame.
*       netdev  Linux netdevice.
*
* Side effects:
*       If the lower layers report that buffers are full. netdev->tbusy
*       will be set to prevent higher layers from sending more traffic.
*
*       Note: If this function returns non-zero, higher layers retain
*             ownership of the skb.
*
* Returns:
*       zero on success, non-zero on failure.
----------------------------------------------------------------*/
static int p80211knetdev_hard_start_xmit(struct sk_buff *skb,
                                         netdevice_t *netdev)
{
        int result = 0;
        int txresult = -1;
        wlandevice_t *wlandev = netdev->ml_priv;
        union p80211_hdr p80211_hdr;
        struct p80211_metawep p80211_wep;

        p80211_wep.data = NULL;

        if (skb == NULL)
                return NETDEV_TX_OK;

        if (wlandev->state != WLAN_DEVICE_OPEN) {
                result = 1;
                goto failed;
        }

        memset(&p80211_hdr, 0, sizeof(union p80211_hdr));
        memset(&p80211_wep, 0, sizeof(struct p80211_metawep));

        if (netif_queue_stopped(netdev)) {
                pr_debug("called when queue stopped.\n");
                result = 1;
                goto failed;
        }

        netif_stop_queue(netdev);

        /* Check to see that a valid mode is set */
        switch (wlandev->macmode) {
        case WLAN_MACMODE_IBSS_STA:
        case WLAN_MACMODE_ESS_STA:
        case WLAN_MACMODE_ESS_AP:
                break;
        default:
                /* Mode isn't set yet, just drop the frame
                 * and return success .
                 * TODO: we need a saner way to handle this
                 */
                if (skb->protocol != ETH_P_80211_RAW) {
                        netif_start_queue(wlandev->netdev);
                        printk(KERN_NOTICE
                               "Tx attempt prior to association, frame dropped.\n");
                        wlandev->linux_stats.tx_dropped++;
                        result = 0;
                        goto failed;
                }
                break;
        }

        /* Check for raw transmits */
        if (skb->protocol == ETH_P_80211_RAW) {
                if (!capable(CAP_NET_ADMIN)) {
                        result = 1;
                        goto failed;
                }
                /* move the header over */
                memcpy(&p80211_hdr, skb->data, sizeof(union p80211_hdr));
                skb_pull(skb, sizeof(union p80211_hdr));
        } else {
                if (skb_ether_to_p80211
                    (wlandev, wlandev->ethconv, skb, &p80211_hdr,
                     &p80211_wep) != 0) {
                        /* convert failed */
                        pr_debug("ether_to_80211(%d) failed.\n",
                                 wlandev->ethconv);
                        result = 1;
                        goto failed;
                }
        }
        if (wlandev->txframe == NULL) {
                result = 1;
                goto failed;
        }

        netdev->trans_start = jiffies;

        wlandev->linux_stats.tx_packets++;
        /* count only the packet payload */
        wlandev->linux_stats.tx_bytes += skb->len;

        txresult = wlandev->txframe(wlandev, skb, &p80211_hdr, &p80211_wep);

        if (txresult == 0) {
                /* success and more buf */
                /* avail, re: hw_txdata */
                netif_wake_queue(wlandev->netdev);
                result = NETDEV_TX_OK;
        } else if (txresult == 1) {
                /* success, no more avail */
                pr_debug("txframe success, no more bufs\n");
                /* netdev->tbusy = 1;  don't set here, irqhdlr */
                /*   may have already cleared it */
                result = NETDEV_TX_OK;
        } else if (txresult == 2) {
                /* alloc failure, drop frame */
                pr_debug("txframe returned alloc_fail\n");
                result = NETDEV_TX_BUSY;
        } else {
                /* buffer full or queue busy, drop frame. */
                pr_debug("txframe returned full or busy\n");
                result = NETDEV_TX_BUSY;
        }

failed:
        /* Free up the WEP buffer if it's not the same as the skb */
        if ((p80211_wep.data) && (p80211_wep.data != skb->data))
                kzfree(p80211_wep.data);

        /* we always free the skb here, never in a lower level. */
        if (!result)
                dev_kfree_skb(skb);

        return result;
}

/*----------------------------------------------------------------
* p80211knetdev_set_multicast_list
*
* Called from higher layers whenever there's a need to set/clear
* promiscuous mode or rewrite the multicast list.
*
* Arguments:
*       none
*
* Returns:
*       nothing
----------------------------------------------------------------*/
static void p80211knetdev_set_multicast_list(netdevice_t *dev)
{
        wlandevice_t *wlandev = dev->ml_priv;

        /* TODO:  real multicast support as well */

        if (wlandev->set_multicast_list)
                wlandev->set_multicast_list(wlandev, dev);

}

#ifdef SIOCETHTOOL

static int p80211netdev_ethtool(wlandevice_t *wlandev, void __user *useraddr)
{
        u32 ethcmd;
        struct ethtool_drvinfo info;
        struct ethtool_value edata;

        memset(&info, 0, sizeof(info));
        memset(&edata, 0, sizeof(edata));

        if (copy_from_user(&ethcmd, useraddr, sizeof(ethcmd)))
                return -EFAULT;

        switch (ethcmd) {
        case ETHTOOL_GDRVINFO:
                info.cmd = ethcmd;
                snprintf(info.driver, sizeof(info.driver), "p80211_%s",
                         wlandev->nsdname);
                snprintf(info.version, sizeof(info.version), "%s",
                         WLAN_RELEASE);

                if (copy_to_user(useraddr, &info, sizeof(info)))
                        return -EFAULT;
                return 0;
#ifdef ETHTOOL_GLINK
        case ETHTOOL_GLINK:
                edata.cmd = ethcmd;

                if (wlandev->linkstatus &&
                    (wlandev->macmode != WLAN_MACMODE_NONE)) {
                        edata.data = 1;
                } else {
                        edata.data = 0;
                }

                if (copy_to_user(useraddr, &edata, sizeof(edata)))
                        return -EFAULT;
                return 0;
#endif
        }

        return -EOPNOTSUPP;
}

#endif

/*----------------------------------------------------------------
* p80211knetdev_do_ioctl
*
* Handle an ioctl call on one of our devices.  Everything Linux
* ioctl specific is done here.  Then we pass the contents of the
* ifr->data to the request message handler.
*
* Arguments:
*       dev     Linux kernel netdevice
*       ifr     Our private ioctl request structure, typed for the
*               generic struct ifreq so we can use ptr to func
*               w/o cast.
*
* Returns:
*       zero on success, a negative errno on failure.  Possible values:
*               -ENETDOWN Device isn't up.
*               -EBUSY  cmd already in progress
*               -ETIME  p80211 cmd timed out (MSD may have its own timers)
*               -EFAULT memory fault copying msg from user buffer
*               -ENOMEM unable to allocate kernel msg buffer
*               -ENOSYS bad magic, it the cmd really for us?
*               -EintR  sleeping on cmd, awakened by signal, cmd cancelled.
*
* Call Context:
*       Process thread (ioctl caller).  TODO: SMP support may require
*       locks.
----------------------------------------------------------------*/
static int p80211knetdev_do_ioctl(netdevice_t *dev, struct ifreq *ifr, int cmd)
{
        int result = 0;
        struct p80211ioctl_req *req = (struct p80211ioctl_req *) ifr;
        wlandevice_t *wlandev = dev->ml_priv;
        u8 *msgbuf;

        pr_debug("rx'd ioctl, cmd=%d, len=%d\n", cmd, req->len);

#ifdef SIOCETHTOOL
        if (cmd == SIOCETHTOOL) {
                result =
                    p80211netdev_ethtool(wlandev, (void __user *)ifr->ifr_data);
                goto bail;
        }
#endif

        /* Test the magic, assume ifr is good if it's there */
        if (req->magic != P80211_IOCTL_MAGIC) {
                result = -ENOSYS;
                goto bail;
        }

        if (cmd == P80211_IFTEST) {
                result = 0;
                goto bail;
        } else if (cmd != P80211_IFREQ) {
                result = -ENOSYS;
                goto bail;
        }

        /* Allocate a buf of size req->len */
        msgbuf = kmalloc(req->len, GFP_KERNEL);
        if (msgbuf) {
                if (copy_from_user(msgbuf, (void __user *)req->data, req->len))
                        result = -EFAULT;
                else
                        result = p80211req_dorequest(wlandev, msgbuf);

                if (result == 0) {
                        if (copy_to_user
                            ((void __user *)req->data, msgbuf, req->len)) {
                                result = -EFAULT;
                        }
                }
                kfree(msgbuf);
        } else {
                result = -ENOMEM;
        }
bail:
        /* If allocate,copyfrom or copyto fails, return errno */
        return result;
}

/*----------------------------------------------------------------
* p80211knetdev_set_mac_address
*
* Handles the ioctl for changing the MACAddress of a netdevice
*
* references: linux/netdevice.h and drivers/net/net_init.c
*
* NOTE: [MSM] We only prevent address changes when the netdev is
* up.  We don't control anything based on dot11 state.  If the
* address is changed on a STA that's currently associated, you
* will probably lose the ability to send and receive data frames.
* Just be aware.  Therefore, this should usually only be done
* prior to scan/join/auth/assoc.
*
* Arguments:
*       dev     netdevice struct
*       addr    the new MACAddress (a struct)
*
* Returns:
*       zero on success, a negative errno on failure.  Possible values:
*               -EBUSY  device is bussy (cmd not possible)
*               -and errors returned by: p80211req_dorequest(..)
*
* by: Collin R. Mulliner <collin@mulliner.org>
----------------------------------------------------------------*/
static int p80211knetdev_set_mac_address(netdevice_t *dev, void *addr)
{
        struct sockaddr *new_addr = addr;
        struct p80211msg_dot11req_mibset dot11req;
        p80211item_unk392_t *mibattr;
        p80211item_pstr6_t *macaddr;
        p80211item_uint32_t *resultcode;
        int result;

        /* If we're running, we don't allow MAC address changes */
        if (netif_running(dev))
                return -EBUSY;

        /* Set up some convenience pointers. */
        mibattr = &dot11req.mibattribute;
        macaddr = (p80211item_pstr6_t *) &mibattr->data;
        resultcode = &dot11req.resultcode;

        /* Set up a dot11req_mibset */
        memset(&dot11req, 0, sizeof(struct p80211msg_dot11req_mibset));
        dot11req.msgcode = DIDmsg_dot11req_mibset;
        dot11req.msglen = sizeof(struct p80211msg_dot11req_mibset);
        memcpy(dot11req.devname,
               ((wlandevice_t *) dev->ml_priv)->name, WLAN_DEVNAMELEN_MAX - 1);

        /* Set up the mibattribute argument */
        mibattr->did = DIDmsg_dot11req_mibset_mibattribute;
        mibattr->status = P80211ENUM_msgitem_status_data_ok;
        mibattr->len = sizeof(mibattr->data);

        macaddr->did = DIDmib_dot11mac_dot11OperationTable_dot11MACAddress;
        macaddr->status = P80211ENUM_msgitem_status_data_ok;
        macaddr->len = sizeof(macaddr->data);
        macaddr->data.len = ETH_ALEN;
        memcpy(&macaddr->data.data, new_addr->sa_data, ETH_ALEN);

        /* Set up the resultcode argument */
        resultcode->did = DIDmsg_dot11req_mibset_resultcode;
        resultcode->status = P80211ENUM_msgitem_status_no_value;
        resultcode->len = sizeof(resultcode->data);
        resultcode->data = 0;

        /* now fire the request */
        result = p80211req_dorequest(dev->ml_priv, (u8 *) &dot11req);

        /* If the request wasn't successful, report an error and don't
         * change the netdev address
         */
        if (result != 0 || resultcode->data != P80211ENUM_resultcode_success) {
                printk(KERN_ERR
                       "Low-level driver failed dot11req_mibset(dot11MACAddress).\n");
                result = -EADDRNOTAVAIL;
        } else {
                /* everything's ok, change the addr in netdev */
                memcpy(dev->dev_addr, new_addr->sa_data, dev->addr_len);
        }

        return result;
}

static int wlan_change_mtu(netdevice_t *dev, int new_mtu)
{
        /* 2312 is max 802.11 payload, 20 is overhead, (ether + llc +snap)
           and another 8 for wep. */
        if ((new_mtu < 68) || (new_mtu > (2312 - 20 - 8)))
                return -EINVAL;

        dev->mtu = new_mtu;

        return 0;
}

static const struct net_device_ops p80211_netdev_ops = {
        .ndo_init = p80211knetdev_init,
        .ndo_open = p80211knetdev_open,
        .ndo_stop = p80211knetdev_stop,
        .ndo_get_stats = p80211knetdev_get_stats,
        .ndo_start_xmit = p80211knetdev_hard_start_xmit,
        .ndo_set_rx_mode = p80211knetdev_set_multicast_list,
        .ndo_do_ioctl = p80211knetdev_do_ioctl,
        .ndo_set_mac_address = p80211knetdev_set_mac_address,
        .ndo_tx_timeout = p80211knetdev_tx_timeout,
        .ndo_change_mtu = wlan_change_mtu,
        .ndo_validate_addr = eth_validate_addr,
};

/*----------------------------------------------------------------
* wlan_setup
*
* Roughly matches the functionality of ether_setup.  Here
* we set up any members of the wlandevice structure that are common
* to all devices.  Additionally, we allocate a linux 'struct device'
* and perform the same setup as ether_setup.
*
* Note: It's important that the caller have setup the wlandev->name
*       ptr prior to calling this function.
*
* Arguments:
*       wlandev         ptr to the wlandev structure for the
*                       interface.
*       physdev         ptr to usb device
* Returns:
*       zero on success, non-zero otherwise.
* Call Context:
*       Should be process thread.  We'll assume it might be
*       interrupt though.  When we add support for statically
*       compiled drivers, this function will be called in the
*       context of the kernel startup code.
----------------------------------------------------------------*/
int wlan_setup(wlandevice_t *wlandev, struct device *physdev)
{
        int result = 0;
        netdevice_t *netdev;
        struct wiphy *wiphy;
        struct wireless_dev *wdev;

        /* Set up the wlandev */
        wlandev->state = WLAN_DEVICE_CLOSED;
        wlandev->ethconv = WLAN_ETHCONV_8021h;
        wlandev->macmode = WLAN_MACMODE_NONE;

        /* Set up the rx queue */
        skb_queue_head_init(&wlandev->nsd_rxq);
        tasklet_init(&wlandev->rx_bh,
                     p80211netdev_rx_bh, (unsigned long)wlandev);

        /* Allocate and initialize the wiphy struct */
        wiphy = wlan_create_wiphy(physdev, wlandev);
        if (wiphy == NULL) {
                printk(KERN_ERR "Failed to alloc wiphy.\n");
                return 1;
        }

        /* Allocate and initialize the struct device */
        netdev = alloc_netdev(sizeof(struct wireless_dev), "wlan%d",
                                ether_setup);
        if (netdev == NULL) {
                printk(KERN_ERR "Failed to alloc netdev.\n");
                wlan_free_wiphy(wiphy);
                result = 1;
        } else {
                wlandev->netdev = netdev;
                netdev->ml_priv = wlandev;
                netdev->netdev_ops = &p80211_netdev_ops;
                wdev = netdev_priv(netdev);
                wdev->wiphy = wiphy;
                wdev->iftype = NL80211_IFTYPE_STATION;
                netdev->ieee80211_ptr = wdev;

                netif_stop_queue(netdev);
                netif_carrier_off(netdev);
        }

        return result;
}

/*----------------------------------------------------------------
* wlan_unsetup
*
* This function is paired with the wlan_setup routine.  It should
* be called after unregister_wlandev.  Basically, all it does is
* free the 'struct device' that's associated with the wlandev.
* We do it here because the 'struct device' isn't allocated
* explicitly in the driver code, it's done in wlan_setup.  To
* do the free in the driver might seem like 'magic'.
*
* Arguments:
*       wlandev         ptr to the wlandev structure for the
*                       interface.
* Call Context:
*       Should be process thread.  We'll assume it might be
*       interrupt though.  When we add support for statically
*       compiled drivers, this function will be called in the
*       context of the kernel startup code.
----------------------------------------------------------------*/
void wlan_unsetup(wlandevice_t *wlandev)
{
        struct wireless_dev *wdev;

        tasklet_kill(&wlandev->rx_bh);

        if (wlandev->netdev) {
                wdev = netdev_priv(wlandev->netdev);
                if (wdev->wiphy)
                        wlan_free_wiphy(wdev->wiphy);
                free_netdev(wlandev->netdev);
                wlandev->netdev = NULL;
        }
}

/*----------------------------------------------------------------
* register_wlandev
*
* Roughly matches the functionality of register_netdev.  This function
* is called after the driver has successfully probed and set up the
* resources for the device.  It's now ready to become a named device
* in the Linux system.
*
* First we allocate a name for the device (if not already set), then
* we call the Linux function register_netdevice.
*
* Arguments:
*       wlandev         ptr to the wlandev structure for the
*                       interface.
* Returns:
*       zero on success, non-zero otherwise.
* Call Context:
*       Can be either interrupt or not.
----------------------------------------------------------------*/
int register_wlandev(wlandevice_t *wlandev)
{
        return register_netdev(wlandev->netdev);
}

/*----------------------------------------------------------------
* unregister_wlandev
*
* Roughly matches the functionality of unregister_netdev.  This
* function is called to remove a named device from the system.
*
* First we tell linux that the device should no longer exist.
* Then we remove it from the list of known wlan devices.
*
* Arguments:
*       wlandev         ptr to the wlandev structure for the
*                       interface.
* Returns:
*       zero on success, non-zero otherwise.
* Call Context:
*       Can be either interrupt or not.
----------------------------------------------------------------*/
int unregister_wlandev(wlandevice_t *wlandev)
{
        struct sk_buff *skb;

        unregister_netdev(wlandev->netdev);

        /* Now to clean out the rx queue */
        while ((skb = skb_dequeue(&wlandev->nsd_rxq)))
                dev_kfree_skb(skb);

        return 0;
}

/*----------------------------------------------------------------
* p80211netdev_hwremoved
*
* Hardware removed notification. This function should be called
* immediately after an MSD has detected that the underlying hardware
* has been yanked out from under us.  The primary things we need
* to do are:
*   - Mark the wlandev
*   - Prevent any further traffic from the knetdev i/f
*   - Prevent any further requests from mgmt i/f
*   - If there are any waitq'd mgmt requests or mgmt-frame exchanges,
*     shut them down.
*   - Call the MSD hwremoved function.
*
* The remainder of the cleanup will be handled by unregister().
* Our primary goal here is to prevent as much tickling of the MSD
* as possible since the MSD is already in a 'wounded' state.
*
* TODO: As new features are added, this function should be
*       updated.
*
* Arguments:
*       wlandev         WLAN network device structure
* Returns:
*       nothing
* Side effects:
*
* Call context:
*       Usually interrupt.
----------------------------------------------------------------*/
void p80211netdev_hwremoved(wlandevice_t *wlandev)
{
        wlandev->hwremoved = 1;
        if (wlandev->state == WLAN_DEVICE_OPEN)
                netif_stop_queue(wlandev->netdev);

        netif_device_detach(wlandev->netdev);
}

/*----------------------------------------------------------------
* p80211_rx_typedrop
*
* Classifies the frame, increments the appropriate counter, and
* returns 0|1|2 indicating whether the driver should handle, ignore, or
* drop the frame
*
* Arguments:
*       wlandev         wlan device structure
*       fc              frame control field
*
* Returns:
*       zero if the frame should be handled by the driver,
*       one if the frame should be ignored
*       anything else means we drop it.
*
* Side effects:
*
* Call context:
*       interrupt
----------------------------------------------------------------*/
static int p80211_rx_typedrop(wlandevice_t *wlandev, u16 fc)
{
        u16 ftype;
        u16 fstype;
        int drop = 0;
        /* Classify frame, increment counter */
        ftype = WLAN_GET_FC_FTYPE(fc);
        fstype = WLAN_GET_FC_FSTYPE(fc);
#if 0
        pr_debug("rx_typedrop : ftype=%d fstype=%d.\n", ftype, fstype);
#endif
        switch (ftype) {
        case WLAN_FTYPE_MGMT:
                if ((wlandev->netdev->flags & IFF_PROMISC) ||
                    (wlandev->netdev->flags & IFF_ALLMULTI)) {
                        drop = 1;
                        break;
                }
                pr_debug("rx'd mgmt:\n");
                wlandev->rx.mgmt++;
                switch (fstype) {
                case WLAN_FSTYPE_ASSOCREQ:
                        /* printk("assocreq"); */
                        wlandev->rx.assocreq++;
                        break;
                case WLAN_FSTYPE_ASSOCRESP:
                        /* printk("assocresp"); */
                        wlandev->rx.assocresp++;
                        break;
                case WLAN_FSTYPE_REASSOCREQ:
                        /* printk("reassocreq"); */
                        wlandev->rx.reassocreq++;
                        break;
                case WLAN_FSTYPE_REASSOCRESP:
                        /* printk("reassocresp"); */
                        wlandev->rx.reassocresp++;
                        break;
                case WLAN_FSTYPE_PROBEREQ:
                        /* printk("probereq"); */
                        wlandev->rx.probereq++;
                        break;
                case WLAN_FSTYPE_PROBERESP:
                        /* printk("proberesp"); */
                        wlandev->rx.proberesp++;
                        break;
                case WLAN_FSTYPE_BEACON:
                        /* printk("beacon"); */
                        wlandev->rx.beacon++;
                        break;
                case WLAN_FSTYPE_ATIM:
                        /* printk("atim"); */
                        wlandev->rx.atim++;
                        break;
                case WLAN_FSTYPE_DISASSOC:
                        /* printk("disassoc"); */
                        wlandev->rx.disassoc++;
                        break;
                case WLAN_FSTYPE_AUTHEN:
                        /* printk("authen"); */
                        wlandev->rx.authen++;
                        break;
                case WLAN_FSTYPE_DEAUTHEN:
                        /* printk("deauthen"); */
                        wlandev->rx.deauthen++;
                        break;
                default:
                        /* printk("unknown"); */
                        wlandev->rx.mgmt_unknown++;
                        break;
                }
                /* printk("\n"); */
                drop = 2;
                break;

        case WLAN_FTYPE_CTL:
                if ((wlandev->netdev->flags & IFF_PROMISC) ||
                    (wlandev->netdev->flags & IFF_ALLMULTI)) {
                        drop = 1;
                        break;
                }
                pr_debug("rx'd ctl:\n");
                wlandev->rx.ctl++;
                switch (fstype) {
                case WLAN_FSTYPE_PSPOLL:
                        /* printk("pspoll"); */
                        wlandev->rx.pspoll++;
                        break;
                case WLAN_FSTYPE_RTS:
                        /* printk("rts"); */
                        wlandev->rx.rts++;
                        break;
                case WLAN_FSTYPE_CTS:
                        /* printk("cts"); */
                        wlandev->rx.cts++;
                        break;
                case WLAN_FSTYPE_ACK:
                        /* printk("ack"); */
                        wlandev->rx.ack++;
                        break;
                case WLAN_FSTYPE_CFEND:
                        /* printk("cfend"); */
                        wlandev->rx.cfend++;
                        break;
                case WLAN_FSTYPE_CFENDCFACK:
                        /* printk("cfendcfack"); */
                        wlandev->rx.cfendcfack++;
                        break;
                default:
                        /* printk("unknown"); */
                        wlandev->rx.ctl_unknown++;
                        break;
                }
                /* printk("\n"); */
                drop = 2;
                break;

        case WLAN_FTYPE_DATA:
                wlandev->rx.data++;
                switch (fstype) {
                case WLAN_FSTYPE_DATAONLY:
                        wlandev->rx.dataonly++;
                        break;
                case WLAN_FSTYPE_DATA_CFACK:
                        wlandev->rx.data_cfack++;
                        break;
                case WLAN_FSTYPE_DATA_CFPOLL:
                        wlandev->rx.data_cfpoll++;
                        break;
                case WLAN_FSTYPE_DATA_CFACK_CFPOLL:
                        wlandev->rx.data__cfack_cfpoll++;
                        break;
                case WLAN_FSTYPE_NULL:
                        pr_debug("rx'd data:null\n");
                        wlandev->rx.null++;
                        break;
                case WLAN_FSTYPE_CFACK:
                        pr_debug("rx'd data:cfack\n");
                        wlandev->rx.cfack++;
                        break;
                case WLAN_FSTYPE_CFPOLL:
                        pr_debug("rx'd data:cfpoll\n");
                        wlandev->rx.cfpoll++;
                        break;
                case WLAN_FSTYPE_CFACK_CFPOLL:
                        pr_debug("rx'd data:cfack_cfpoll\n");
                        wlandev->rx.cfack_cfpoll++;
                        break;
                default:
                        /* printk("unknown"); */
                        wlandev->rx.data_unknown++;
                        break;
                }

                break;
        }
        return drop;
}

static void p80211knetdev_tx_timeout(netdevice_t *netdev)
{
        wlandevice_t *wlandev = netdev->ml_priv;

        if (wlandev->tx_timeout) {
                wlandev->tx_timeout(wlandev);
        } else {
                printk(KERN_WARNING "Implement tx_timeout for %s\n",
                       wlandev->nsdname);
                netif_wake_queue(wlandev->netdev);
        }
}