drivers/ata/pata_cs5535.c

   1 // SPDX-License-Identifier: GPL-2.0-only
   2 /*
   3  * pata-cs5535.c        - CS5535 PATA for new ATA layer
   4  *                        (C) 2005-2006 Red Hat Inc
   5  *                        Alan Cox <alan@lxorguk.ukuu.org.uk>
   6  *
   7  * based upon cs5535.c from AMD <Jens.Altmann@amd.com> as cleaned up and
   8  * made readable and Linux style by Wolfgang Zuleger <wolfgang.zuleger@gmx.de>
   9  * and Alexander Kiausch <alex.kiausch@t-online.de>
  10  *
  11  * Loosely based on the piix & svwks drivers.
  12  *
  13  * Documentation:
  14  *      Available from AMD web site.
  15  * TODO
  16  *      Review errata to see if serializing is necessary
  17  */
  18
  19 #include <linux/kernel.h>
  20 #include <linux/module.h>
  21 #include <linux/pci.h>
  22 #include <linux/blkdev.h>
  23 #include <linux/delay.h>
  24 #include <scsi/scsi_host.h>
  25 #include <linux/libata.h>
  26 #include <asm/msr.h>
  27
  28 #define DRV_NAME        "pata_cs5535"
  29 #define DRV_VERSION     "0.2.12"
  30
  31 /*
  32  *      The Geode (Aka Athlon GX now) uses an internal MSR based
  33  *      bus system for control. Demented but there you go.
  34  */
  35
  36 #define MSR_ATAC_BASE           0x51300000
  37 #define ATAC_GLD_MSR_CAP        (MSR_ATAC_BASE+0)
  38 #define ATAC_GLD_MSR_CONFIG    (MSR_ATAC_BASE+0x01)
  39 #define ATAC_GLD_MSR_SMI       (MSR_ATAC_BASE+0x02)
  40 #define ATAC_GLD_MSR_ERROR     (MSR_ATAC_BASE+0x03)
  41 #define ATAC_GLD_MSR_PM        (MSR_ATAC_BASE+0x04)
  42 #define ATAC_GLD_MSR_DIAG      (MSR_ATAC_BASE+0x05)
  43 #define ATAC_IO_BAR            (MSR_ATAC_BASE+0x08)
  44 #define ATAC_RESET             (MSR_ATAC_BASE+0x10)
  45 #define ATAC_CH0D0_PIO         (MSR_ATAC_BASE+0x20)
  46 #define ATAC_CH0D0_DMA         (MSR_ATAC_BASE+0x21)
  47 #define ATAC_CH0D1_PIO         (MSR_ATAC_BASE+0x22)
  48 #define ATAC_CH0D1_DMA         (MSR_ATAC_BASE+0x23)
  49 #define ATAC_PCI_ABRTERR       (MSR_ATAC_BASE+0x24)
  50
  51 #define ATAC_BM0_CMD_PRIM      0x00
  52 #define ATAC_BM0_STS_PRIM      0x02
  53 #define ATAC_BM0_PRD           0x04
  54
  55 #define CS5535_CABLE_DETECT    0x48
  56
  57 /**
  58  *      cs5535_cable_detect     -       detect cable type
  59  *      @ap: Port to detect on
  60  *
  61  *      Perform cable detection for ATA66 capable cable. Return a libata
  62  *      cable type.
  63  */
  64
  65 static int cs5535_cable_detect(struct ata_port *ap)
  66 {
  67         u8 cable;
  68         struct pci_dev *pdev = to_pci_dev(ap->host->dev);
  69
  70         pci_read_config_byte(pdev, CS5535_CABLE_DETECT, &cable);
  71         if (cable & 1)
  72                 return ATA_CBL_PATA80;
  73         else
  74                 return ATA_CBL_PATA40;
  75 }
  76
  77 /**
  78  *      cs5535_set_piomode              -       PIO setup
  79  *      @ap: ATA interface
  80  *      @adev: device on the interface
  81  *
  82  *      Set our PIO requirements. The CS5535 is pretty clean about all this
  83  */
  84
  85 static void cs5535_set_piomode(struct ata_port *ap, struct ata_device *adev)
  86 {
  87         static const u16 pio_timings[5] = {
  88                 0xF7F4, 0xF173, 0x8141, 0x5131, 0x1131
  89         };
  90         static const u16 pio_cmd_timings[5] = {
  91                 0xF7F4, 0x53F3, 0x13F1, 0x5131, 0x1131
  92         };
  93         u32 reg, dummy;
  94         struct ata_device *pair = ata_dev_pair(adev);
  95
  96         int mode = adev->pio_mode - XFER_PIO_0;
  97         int cmdmode = mode;
  98
  99         /* Command timing has to be for the lowest of the pair of devices */
 100         if (pair) {
 101                 int pairmode = pair->pio_mode - XFER_PIO_0;
 102                 cmdmode = min(mode, pairmode);
 103                 /* Write the other drive timing register if it changed */
 104                 if (cmdmode < pairmode)
 105                         wrmsr(ATAC_CH0D0_PIO + 2 * pair->devno,
 106                                 pio_cmd_timings[cmdmode] << 16 | pio_timings[pairmode], 0);
 107         }
 108         /* Write the drive timing register */
 109         wrmsr(ATAC_CH0D0_PIO + 2 * adev->devno,
 110                 pio_cmd_timings[cmdmode] << 16 | pio_timings[mode], 0);
 111
 112         /* Set the PIO "format 1" bit in the DMA timing register */
 113         rdmsr(ATAC_CH0D0_DMA + 2 * adev->devno, reg, dummy);
 114         wrmsr(ATAC_CH0D0_DMA + 2 * adev->devno, reg | 0x80000000UL, 0);
 115 }
 116
 117 /**
 118  *      cs5535_set_dmamode              -       DMA timing setup
 119  *      @ap: ATA interface
 120  *      @adev: Device being configured
 121  *
 122  */
 123
 124 static void cs5535_set_dmamode(struct ata_port *ap, struct ata_device *adev)
 125 {
 126         static const u32 udma_timings[5] = {
 127                 0x7F7436A1, 0x7F733481, 0x7F723261, 0x7F713161, 0x7F703061
 128         };
 129         static const u32 mwdma_timings[3] = {
 130                 0x7F0FFFF3, 0x7F035352, 0x7F024241
 131         };
 132         u32 reg, dummy;
 133         int mode = adev->dma_mode;
 134
 135         rdmsr(ATAC_CH0D0_DMA + 2 * adev->devno, reg, dummy);
 136         reg &= 0x80000000UL;
 137         if (mode >= XFER_UDMA_0)
 138                 reg |= udma_timings[mode - XFER_UDMA_0];
 139         else
 140                 reg |= mwdma_timings[mode - XFER_MW_DMA_0];
 141         wrmsr(ATAC_CH0D0_DMA + 2 * adev->devno, reg, 0);
 142 }
 143
 144 static struct scsi_host_template cs5535_sht = {
 145         ATA_BMDMA_SHT(DRV_NAME),
 146 };
 147
 148 static struct ata_port_operations cs5535_port_ops = {
 149         .inherits       = &ata_bmdma_port_ops,
 150         .cable_detect   = cs5535_cable_detect,
 151         .set_piomode    = cs5535_set_piomode,
 152         .set_dmamode    = cs5535_set_dmamode,
 153 };
 154
 155 /**
 156  *      cs5535_init_one         -       Initialise a CS5530
 157  *      @dev: PCI device
 158  *      @id: Entry in match table
 159  *
 160  *      Install a driver for the newly found CS5530 companion chip. Most of
 161  *      this is just housekeeping. We have to set the chip up correctly and
 162  *      turn off various bits of emulation magic.
 163  */
 164
 165 static int cs5535_init_one(struct pci_dev *dev, const struct pci_device_id *id)
 166 {
 167         static const struct ata_port_info info = {
 168                 .flags = ATA_FLAG_SLAVE_POSS,
 169                 .pio_mask = ATA_PIO4,
 170                 .mwdma_mask = ATA_MWDMA2,
 171                 .udma_mask = ATA_UDMA4,
 172                 .port_ops = &cs5535_port_ops
 173         };
 174         const struct ata_port_info *ppi[] = { &info, &ata_dummy_port_info };
 175
 176         return ata_pci_bmdma_init_one(dev, ppi, &cs5535_sht, NULL, 0);
 177 }
 178
 179 static const struct pci_device_id cs5535[] = {
 180         { PCI_VDEVICE(NS, PCI_DEVICE_ID_NS_CS5535_IDE), },
 181         { PCI_VDEVICE(AMD, PCI_DEVICE_ID_AMD_CS5535_IDE), },
 182
 183         { },
 184 };
 185
 186 static struct pci_driver cs5535_pci_driver = {
 187         .name           = DRV_NAME,
 188         .id_table       = cs5535,
 189         .probe          = cs5535_init_one,
 190         .remove         = ata_pci_remove_one,
 191 #ifdef CONFIG_PM_SLEEP
 192         .suspend        = ata_pci_device_suspend,
 193         .resume         = ata_pci_device_resume,
 194 #endif
 195 };
 196
 197 module_pci_driver(cs5535_pci_driver);
 198
 199 MODULE_AUTHOR("Alan Cox, Jens Altmann, Wolfgan Zuleger, Alexander Kiausch");
 200 MODULE_DESCRIPTION("low-level driver for the NS/AMD 5535");
 201 MODULE_LICENSE("GPL");
 202 MODULE_DEVICE_TABLE(pci, cs5535);
 203 MODULE_VERSION(DRV_VERSION);