drivers/usb/host/xhci-rcar.c

   1 // SPDX-License-Identifier: GPL-2.0
   2 /*
   3  * xHCI host controller driver for R-Car SoCs
   4  *
   5  * Copyright (C) 2014 Renesas Electronics Corporation
   6  */
   7
   8 #include <linux/firmware.h>
   9 #include <linux/module.h>
  10 #include <linux/platform_device.h>
  11 #include <linux/of.h>
  12 #include <linux/usb/phy.h>
  13 #include <linux/sys_soc.h>
  14
  15 #include "xhci.h"
  16 #include "xhci-plat.h"
  17 #include "xhci-rcar.h"
  18
  19 /*
  20 * - The V3 firmware is for almost all R-Car Gen3 (except r8a7795 ES1.x)
  21 * - The V2 firmware is for r8a7795 ES1.x.
  22 * - The V2 firmware is possible to use on R-Car Gen2. However, the V2 causes
  23 *   performance degradation. So, this driver continues to use the V1 if R-Car
  24 *   Gen2.
  25 * - The V1 firmware is impossible to use on R-Car Gen3.
  26 */
  27 MODULE_FIRMWARE(XHCI_RCAR_FIRMWARE_NAME_V1);
  28 MODULE_FIRMWARE(XHCI_RCAR_FIRMWARE_NAME_V2);
  29 MODULE_FIRMWARE(XHCI_RCAR_FIRMWARE_NAME_V3);
  30
  31 /*** Register Offset ***/
  32 #define RCAR_USB3_AXH_STA       0x104   /* AXI Host Control Status */
  33 #define RCAR_USB3_INT_ENA       0x224   /* Interrupt Enable */
  34 #define RCAR_USB3_DL_CTRL       0x250   /* FW Download Control & Status */
  35 #define RCAR_USB3_FW_DATA0      0x258   /* FW Data0 */
  36
  37 #define RCAR_USB3_LCLK          0xa44   /* LCLK Select */
  38 #define RCAR_USB3_CONF1         0xa48   /* USB3.0 Configuration1 */
  39 #define RCAR_USB3_CONF2         0xa5c   /* USB3.0 Configuration2 */
  40 #define RCAR_USB3_CONF3         0xaa8   /* USB3.0 Configuration3 */
  41 #define RCAR_USB3_RX_POL        0xab0   /* USB3.0 RX Polarity */
  42 #define RCAR_USB3_TX_POL        0xab8   /* USB3.0 TX Polarity */
  43
  44 /*** Register Settings ***/
  45 /* AXI Host Control Status */
  46 #define RCAR_USB3_AXH_STA_B3_PLL_ACTIVE         0x00010000
  47 #define RCAR_USB3_AXH_STA_B2_PLL_ACTIVE         0x00000001
  48 #define RCAR_USB3_AXH_STA_PLL_ACTIVE_MASK (RCAR_USB3_AXH_STA_B3_PLL_ACTIVE | \
  49                                            RCAR_USB3_AXH_STA_B2_PLL_ACTIVE)
  50
  51 /* Interrupt Enable */
  52 #define RCAR_USB3_INT_XHC_ENA   0x00000001
  53 #define RCAR_USB3_INT_PME_ENA   0x00000002
  54 #define RCAR_USB3_INT_HSE_ENA   0x00000004
  55 #define RCAR_USB3_INT_ENA_VAL   (RCAR_USB3_INT_XHC_ENA | \
  56                                 RCAR_USB3_INT_PME_ENA | RCAR_USB3_INT_HSE_ENA)
  57
  58 /* FW Download Control & Status */
  59 #define RCAR_USB3_DL_CTRL_ENABLE        0x00000001
  60 #define RCAR_USB3_DL_CTRL_FW_SUCCESS    0x00000010
  61 #define RCAR_USB3_DL_CTRL_FW_SET_DATA0  0x00000100
  62
  63 /* LCLK Select */
  64 #define RCAR_USB3_LCLK_ENA_VAL  0x01030001
  65
  66 /* USB3.0 Configuration */
  67 #define RCAR_USB3_CONF1_VAL     0x00030204
  68 #define RCAR_USB3_CONF2_VAL     0x00030300
  69 #define RCAR_USB3_CONF3_VAL     0x13802007
  70
  71 /* USB3.0 Polarity */
  72 #define RCAR_USB3_RX_POL_VAL    BIT(21)
  73 #define RCAR_USB3_TX_POL_VAL    BIT(4)
  74
  75 /* For soc_device_attribute */
  76 #define RCAR_XHCI_FIRMWARE_V2   BIT(0) /* FIRMWARE V2 */
  77 #define RCAR_XHCI_FIRMWARE_V3   BIT(1) /* FIRMWARE V3 */
  78
  79 static const struct soc_device_attribute rcar_quirks_match[]  = {
  80         {
  81                 .soc_id = "r8a7795", .revision = "ES1.*",
  82                 .data = (void *)RCAR_XHCI_FIRMWARE_V2,
  83         },
  84         { /* sentinel */ },
  85 };
  86
  87 static void xhci_rcar_start_gen2(struct usb_hcd *hcd)
  88 {
  89         /* LCLK Select */
  90         writel(RCAR_USB3_LCLK_ENA_VAL, hcd->regs + RCAR_USB3_LCLK);
  91         /* USB3.0 Configuration */
  92         writel(RCAR_USB3_CONF1_VAL, hcd->regs + RCAR_USB3_CONF1);
  93         writel(RCAR_USB3_CONF2_VAL, hcd->regs + RCAR_USB3_CONF2);
  94         writel(RCAR_USB3_CONF3_VAL, hcd->regs + RCAR_USB3_CONF3);
  95         /* USB3.0 Polarity */
  96         writel(RCAR_USB3_RX_POL_VAL, hcd->regs + RCAR_USB3_RX_POL);
  97         writel(RCAR_USB3_TX_POL_VAL, hcd->regs + RCAR_USB3_TX_POL);
  98 }
  99
 100 static int xhci_rcar_is_gen2(struct device *dev)
 101 {
 102         struct device_node *node = dev->of_node;
 103
 104         return of_device_is_compatible(node, "renesas,xhci-r8a7790") ||
 105                 of_device_is_compatible(node, "renesas,xhci-r8a7791") ||
 106                 of_device_is_compatible(node, "renesas,xhci-r8a7793") ||
 107                 of_device_is_compatible(node, "renesas,rcar-gen2-xhci");
 108 }
 109
 110 void xhci_rcar_start(struct usb_hcd *hcd)
 111 {
 112         u32 temp;
 113
 114         if (hcd->regs != NULL) {
 115                 /* Interrupt Enable */
 116                 temp = readl(hcd->regs + RCAR_USB3_INT_ENA);
 117                 temp |= RCAR_USB3_INT_ENA_VAL;
 118                 writel(temp, hcd->regs + RCAR_USB3_INT_ENA);
 119                 if (xhci_rcar_is_gen2(hcd->self.controller))
 120                         xhci_rcar_start_gen2(hcd);
 121         }
 122 }
 123
 124 static int xhci_rcar_download_firmware(struct usb_hcd *hcd)
 125 {
 126         struct device *dev = hcd->self.controller;
 127         void __iomem *regs = hcd->regs;
 128         struct xhci_plat_priv *priv = hcd_to_xhci_priv(hcd);
 129         const struct firmware *fw;
 130         int retval, index, j, time;
 131         int timeout = 10000;
 132         u32 data, val, temp;
 133         u32 quirks = 0;
 134         const struct soc_device_attribute *attr;
 135         const char *firmware_name;
 136
 137         attr = soc_device_match(rcar_quirks_match);
 138         if (attr)
 139                 quirks = (uintptr_t)attr->data;
 140
 141         if (quirks & RCAR_XHCI_FIRMWARE_V2)
 142                 firmware_name = XHCI_RCAR_FIRMWARE_NAME_V2;
 143         else if (quirks & RCAR_XHCI_FIRMWARE_V3)
 144                 firmware_name = XHCI_RCAR_FIRMWARE_NAME_V3;
 145         else
 146                 firmware_name = priv->firmware_name;
 147
 148         /* request R-Car USB3.0 firmware */
 149         retval = request_firmware(&fw, firmware_name, dev);
 150         if (retval)
 151                 return retval;
 152
 153         /* download R-Car USB3.0 firmware */
 154         temp = readl(regs + RCAR_USB3_DL_CTRL);
 155         temp |= RCAR_USB3_DL_CTRL_ENABLE;
 156         writel(temp, regs + RCAR_USB3_DL_CTRL);
 157
 158         for (index = 0; index < fw->size; index += 4) {
 159                 /* to avoid reading beyond the end of the buffer */
 160                 for (data = 0, j = 3; j >= 0; j--) {
 161                         if ((j + index) < fw->size)
 162                                 data |= fw->data[index + j] << (8 * j);
 163                 }
 164                 writel(data, regs + RCAR_USB3_FW_DATA0);
 165                 temp = readl(regs + RCAR_USB3_DL_CTRL);
 166                 temp |= RCAR_USB3_DL_CTRL_FW_SET_DATA0;
 167                 writel(temp, regs + RCAR_USB3_DL_CTRL);
 168
 169                 for (time = 0; time < timeout; time++) {
 170                         val = readl(regs + RCAR_USB3_DL_CTRL);
 171                         if ((val & RCAR_USB3_DL_CTRL_FW_SET_DATA0) == 0)
 172                                 break;
 173                         udelay(1);
 174                 }
 175                 if (time == timeout) {
 176                         retval = -ETIMEDOUT;
 177                         break;
 178                 }
 179         }
 180
 181         temp = readl(regs + RCAR_USB3_DL_CTRL);
 182         temp &= ~RCAR_USB3_DL_CTRL_ENABLE;
 183         writel(temp, regs + RCAR_USB3_DL_CTRL);
 184
 185         for (time = 0; time < timeout; time++) {
 186                 val = readl(regs + RCAR_USB3_DL_CTRL);
 187                 if (val & RCAR_USB3_DL_CTRL_FW_SUCCESS) {
 188                         retval = 0;
 189                         break;
 190                 }
 191                 udelay(1);
 192         }
 193         if (time == timeout)
 194                 retval = -ETIMEDOUT;
 195
 196         release_firmware(fw);
 197
 198         return retval;
 199 }
 200
 201 static bool xhci_rcar_wait_for_pll_active(struct usb_hcd *hcd)
 202 {
 203         int timeout = 1000;
 204         u32 val, mask = RCAR_USB3_AXH_STA_PLL_ACTIVE_MASK;
 205
 206         while (timeout > 0) {
 207                 val = readl(hcd->regs + RCAR_USB3_AXH_STA);
 208                 if ((val & mask) == mask)
 209                         return true;
 210                 udelay(1);
 211                 timeout--;
 212         }
 213
 214         return false;
 215 }
 216
 217 /* This function needs to initialize a "phy" of usb before */
 218 int xhci_rcar_init_quirk(struct usb_hcd *hcd)
 219 {
 220         /* If hcd->regs is NULL, we don't just call the following function */
 221         if (!hcd->regs)
 222                 return 0;
 223
 224         if (!xhci_rcar_wait_for_pll_active(hcd))
 225                 return -ETIMEDOUT;
 226
 227         return xhci_rcar_download_firmware(hcd);
 228 }
 229
 230 int xhci_rcar_resume_quirk(struct usb_hcd *hcd)
 231 {
 232         int ret;
 233
 234         ret = xhci_rcar_download_firmware(hcd);
 235         if (!ret)
 236                 xhci_rcar_start(hcd);
 237
 238         return ret;
 239 }