Documentation/devicetree/bindings/input/ads7846.txt

   1 Device tree bindings for TI's ADS7843, ADS7845, ADS7846, ADS7873, TSC2046
   2 SPI driven touch screen controllers.
   3
   4 The node for this driver must be a child node of a SPI controller, hence
   5 all mandatory properties described in
   6
   7         Documentation/devicetree/bindings/spi/spi-bus.txt
   8
   9 must be specified.
  10
  11 Additional required properties:
  12
  13         compatible              Must be one of the following, depending on the
  14                                 model:
  15                                         "ti,tsc2046"
  16                                         "ti,ads7843"
  17                                         "ti,ads7845"
  18                                         "ti,ads7846"
  19                                         "ti,ads7873"
  20
  21         interrupt-parent
  22         interrupts              An interrupt node describing the IRQ line the chip's
  23                                 !PENIRQ pin is connected to.
  24         vcc-supply              A regulator node for the supply voltage.
  25
  26
  27 Optional properties:
  28
  29         ti,vref-delay-usecs             vref supply delay in usecs, 0 for
  30                                         external vref (u16).
  31         ti,vref-mv                      The VREF voltage, in millivolts (u16).
  32                                         Set to 0 to use internal refernce
  33                                         (ADS7846).
  34         ti,keep-vref-on                 set to keep vref on for differential
  35                                         measurements as well
  36         ti,swap-xy                      swap x and y axis
  37         ti,settle-delay-usec            Settling time of the analog signals;
  38                                         a function of Vcc and the capacitance
  39                                         on the X/Y drivers.  If set to non-zero,
  40                                         two samples are taken with settle_delay
  41                                         us apart, and the second one is used.
  42                                         ~150 uSec with 0.01uF caps (u16).
  43         ti,penirq-recheck-delay-usecs   If set to non-zero, after samples are
  44                                         taken this delay is applied and penirq
  45                                         is rechecked, to help avoid false
  46                                         events.  This value is affected by the
  47                                         material used to build the touch layer
  48                                         (u16).
  49         ti,x-plate-ohms                 Resistance of the X-plate,
  50                                         in Ohms (u16).
  51         ti,y-plate-ohms                 Resistance of the Y-plate,
  52                                         in Ohms (u16).
  53         ti,x-min                        Minimum value on the X axis (u16).
  54         ti,y-min                        Minimum value on the Y axis (u16).
  55         ti,x-max                        Maximum value on the X axis (u16).
  56         ti,y-max                        Minimum value on the Y axis (u16).
  57         ti,pressure-min                 Minimum reported pressure value
  58                                         (threshold) - u16.
  59         ti,pressure-max                 Maximum reported pressure value (u16).
  60         ti,debounce-max                 Max number of additional readings per
  61                                         sample (u16).
  62         ti,debounce-tol                 Tolerance used for filtering (u16).
  63         ti,debounce-rep                 Additional consecutive good readings
  64                                         required after the first two (u16).
  65         ti,pendown-gpio-debounce        Platform specific debounce time for the
  66                                         pendown-gpio (u32).
  67         pendown-gpio                    GPIO handle describing the pin the !PENIRQ
  68                                         line is connected to.
  69         wakeup-source                   use any event on touchscreen as wakeup event.
  70                                         (Legacy property support: "linux,wakeup")
  71
  72
  73 Example for a TSC2046 chip connected to an McSPI controller of an OMAP SoC::
  74
  75         spi_controller {
  76                 tsc2046@0 {
  77                         reg = <0>;      /* CS0 */
  78                         compatible = "ti,tsc2046";
  79                         interrupt-parent = <&gpio1>;
  80                         interrupts = <8 0>;     /* BOOT6 / GPIO 8 */
  81                         spi-max-frequency = <1000000>;
  82                         pendown-gpio = <&gpio1 8 0>;
  83                         vcc-supply = <&reg_vcc3>;
  84
  85                         ti,x-min = /bits/ 16 <0>;
  86                         ti,x-max = /bits/ 16 <8000>;
  87                         ti,y-min = /bits/ 16 <0>;
  88                         ti,y-max = /bits/ 16 <4800>;
  89                         ti,x-plate-ohms = /bits/ 16 <40>;
  90                         ti,pressure-max = /bits/ 16 <255>;
  91
  92                         wakeup-source;
  93                 };
  94         };