4 * Copyright 2009-2011 Freescale Semiconductor, Inc.
16 const char *error_text
;
17 } desc_error_list
[] = {
18 { 0x00, "No error." },
19 { 0x01, "SGT Length Error. The descriptor is trying to read more data than is contained in the SGT table." },
20 { 0x02, "SGT Null Entry Error." },
21 { 0x03, "Job Ring Control Error. There is a bad value in the Job Ring Control register." },
22 { 0x04, "Invalid Descriptor Command. The Descriptor Command field is invalid." },
23 { 0x05, "Reserved." },
24 { 0x06, "Invalid KEY Command" },
25 { 0x07, "Invalid LOAD Command" },
26 { 0x08, "Invalid STORE Command" },
27 { 0x09, "Invalid OPERATION Command" },
28 { 0x0A, "Invalid FIFO LOAD Command" },
29 { 0x0B, "Invalid FIFO STORE Command" },
30 { 0x0C, "Invalid MOVE/MOVE_LEN Command" },
31 { 0x0D, "Invalid JUMP Command. A nonlocal JUMP Command is invalid because the target is not a Job Header Command, or the jump is from a Trusted Descriptor to a Job Descriptor, or because the target Descriptor contains a Shared Descriptor." },
32 { 0x0E, "Invalid MATH Command" },
33 { 0x0F, "Invalid SIGNATURE Command" },
34 { 0x10, "Invalid Sequence Command. A SEQ IN PTR OR SEQ OUT PTR Command is invalid or a SEQ KEY, SEQ LOAD, SEQ FIFO LOAD, or SEQ FIFO STORE decremented the input or output sequence length below 0. This error may result if a built-in PROTOCOL Command has encountered a malformed PDU." },
35 { 0x11, "Skip data type invalid. The type must be 0xE or 0xF."},
36 { 0x12, "Shared Descriptor Header Error" },
37 { 0x13, "Header Error. Invalid length or parity, or certain other problems." },
38 { 0x14, "Burster Error. Burster has gotten to an illegal state" },
39 { 0x15, "Context Register Length Error. The descriptor is trying to read or write past the end of the Context Register. A SEQ LOAD or SEQ STORE with the VLF bit set was executed with too large a length in the variable length register (VSOL for SEQ STORE or VSIL for SEQ LOAD)." },
40 { 0x16, "DMA Error" },
41 { 0x17, "Reserved." },
42 { 0x1A, "Job failed due to JR reset" },
43 { 0x1B, "Job failed due to Fail Mode" },
44 { 0x1C, "DECO Watchdog timer timeout error" },
45 { 0x1D, "DECO tried to copy a key from another DECO but the other DECO's Key Registers were locked" },
46 { 0x1E, "DECO attempted to copy data from a DECO that had an unmasked Descriptor error" },
47 { 0x1F, "LIODN error. DECO was trying to share from itself or from another DECO but the two Non-SEQ LIODN values didn't match or the 'shared from' DECO's Descriptor required that the SEQ LIODNs be the same and they aren't." },
48 { 0x20, "DECO has completed a reset initiated via the DRR register" },
49 { 0x21, "Nonce error. When using EKT (CCM) key encryption option in the FIFO STORE Command, the Nonce counter reached its maximum value and this encryption mode can no longer be used." },
50 { 0x22, "Meta data is too large (> 511 bytes) for TLS decap (input frame; block ciphers) and IPsec decap (output frame, when doing the next header byte update) and DCRC (output frame)." },
51 { 0x23, "Read Input Frame error" },
52 { 0x24, "JDKEK, TDKEK or TDSK not loaded error" },
53 { 0x80, "DNR (do not run) error" },
54 { 0x81, "undefined protocol command" },
55 { 0x82, "invalid setting in PDB" },
56 { 0x83, "Anti-replay LATE error" },
57 { 0x84, "Anti-replay REPLAY error" },
58 { 0x85, "Sequence number overflow" },
59 { 0x86, "Sigver invalid signature" },
60 { 0x87, "DSA Sign Illegal test descriptor" },
61 { 0x88, "Protocol Format Error - A protocol has seen an error in the format of data received. When running RSA, this means that formatting with random padding was used, and did not follow the form: 0x00, 0x02, 8-to-N bytes of non-zero pad, 0x00, F data." },
62 { 0x89, "Protocol Size Error - A protocol has seen an error in size. When running RSA, pdb size N < (size of F) when no formatting is used; or pdb size N < (F + 11) when formatting is used." },
63 { 0xC1, "Blob Command error: Undefined mode" },
64 { 0xC2, "Blob Command error: Secure Memory Blob mode error" },
65 { 0xC4, "Blob Command error: Black Blob key or input size error" },
66 { 0xC5, "Blob Command error: Invalid key destination" },
67 { 0xC8, "Blob Command error: Trusted/Secure mode error" },
68 { 0xF0, "IPsec TTL or hop limit field either came in as 0, or was decremented to 0" },
69 { 0xF1, "3GPP HFN matches or exceeds the Threshold" },
72 static const char * const cha_id_list
[] = {
88 static const char * const err_id_list
[] = {
93 "PKHA A memory size error.",
94 "PKHA B memory size error.",
95 "Data arrived out of sequence error.",
96 "PKHA divide-by-zero error.",
97 "PKHA modulus even error.",
98 "DES key parity error.",
101 "Unsupported CCM AAD size.",
102 "Class 1 CHA is not reset",
103 "Invalid CHA combination was selected",
104 "Invalid CHA selected.",
107 static const char * const rng_err_id_list
[] = {
114 "Prediction resistance",
115 "Prediction resistance and test request",
117 "Secure key generation",
120 static void report_ccb_status(struct device
*jrdev
, const u32 status
,
123 u8 cha_id
= (status
& JRSTA_CCBERR_CHAID_MASK
) >>
124 JRSTA_CCBERR_CHAID_SHIFT
;
125 u8 err_id
= status
& JRSTA_CCBERR_ERRID_MASK
;
126 u8 idx
= (status
& JRSTA_DECOERR_INDEX_MASK
) >>
127 JRSTA_DECOERR_INDEX_SHIFT
;
129 const char *cha_str
= "unidentified cha_id value 0x";
130 char cha_err_code
[3] = { 0 };
131 const char *err_str
= "unidentified err_id value 0x";
132 char err_err_code
[3] = { 0 };
134 if (status
& JRSTA_DECOERR_JUMP
)
135 idx_str
= "jump tgt desc idx";
137 idx_str
= "desc idx";
139 if (cha_id
< ARRAY_SIZE(cha_id_list
))
140 cha_str
= cha_id_list
[cha_id
];
142 snprintf(cha_err_code
, sizeof(cha_err_code
), "%02x", cha_id
);
144 if ((cha_id
<< JRSTA_CCBERR_CHAID_SHIFT
) == JRSTA_CCBERR_CHAID_RNG
&&
145 err_id
< ARRAY_SIZE(rng_err_id_list
) &&
146 strlen(rng_err_id_list
[err_id
])) {
148 err_str
= rng_err_id_list
[err_id
];
149 } else if (err_id
< ARRAY_SIZE(err_id_list
))
150 err_str
= err_id_list
[err_id
];
152 snprintf(err_err_code
, sizeof(err_err_code
), "%02x", err_id
);
155 * CCB ICV check failures are part of normal operation life;
156 * we leave the upper layers to do what they want with them.
158 if (err_id
!= JRSTA_CCBERR_ERRID_ICVCHK
)
159 dev_err(jrdev
, "%08x: %s: %s %d: %s%s: %s%s\n",
160 status
, error
, idx_str
, idx
,
161 cha_str
, cha_err_code
,
162 err_str
, err_err_code
);
165 static void report_jump_status(struct device
*jrdev
, const u32 status
,
168 dev_err(jrdev
, "%08x: %s: %s() not implemented\n",
169 status
, error
, __func__
);
172 static void report_deco_status(struct device
*jrdev
, const u32 status
,
175 u8 err_id
= status
& JRSTA_DECOERR_ERROR_MASK
;
176 u8 idx
= (status
& JRSTA_DECOERR_INDEX_MASK
) >>
177 JRSTA_DECOERR_INDEX_SHIFT
;
179 const char *err_str
= "unidentified error value 0x";
180 char err_err_code
[3] = { 0 };
183 if (status
& JRSTA_DECOERR_JUMP
)
184 idx_str
= "jump tgt desc idx";
186 idx_str
= "desc idx";
188 for (i
= 0; i
< ARRAY_SIZE(desc_error_list
); i
++)
189 if (desc_error_list
[i
].value
== err_id
)
192 if (i
!= ARRAY_SIZE(desc_error_list
) && desc_error_list
[i
].error_text
)
193 err_str
= desc_error_list
[i
].error_text
;
195 snprintf(err_err_code
, sizeof(err_err_code
), "%02x", err_id
);
197 dev_err(jrdev
, "%08x: %s: %s %d: %s%s\n",
198 status
, error
, idx_str
, idx
, err_str
, err_err_code
);
201 static void report_jr_status(struct device
*jrdev
, const u32 status
,
204 dev_err(jrdev
, "%08x: %s: %s() not implemented\n",
205 status
, error
, __func__
);
208 static void report_cond_code_status(struct device
*jrdev
, const u32 status
,
211 dev_err(jrdev
, "%08x: %s: %s() not implemented\n",
212 status
, error
, __func__
);
215 void caam_jr_strstatus(struct device
*jrdev
, u32 status
)
217 static const struct stat_src
{
218 void (*report_ssed
)(struct device
*jrdev
, const u32 status
,
222 { NULL
, "No error" },
224 { report_ccb_status
, "CCB" },
225 { report_jump_status
, "Jump" },
226 { report_deco_status
, "DECO" },
227 { NULL
, "Queue Manager Interface" },
228 { report_jr_status
, "Job Ring" },
229 { report_cond_code_status
, "Condition Code" },
239 u32 ssrc
= status
>> JRSTA_SSRC_SHIFT
;
240 const char *error
= status_src
[ssrc
].error
;
243 * If there is an error handling function, call it to report the error.
244 * Otherwise print the error source name.
246 if (status_src
[ssrc
].report_ssed
)
247 status_src
[ssrc
].report_ssed(jrdev
, status
, error
);
249 dev_err(jrdev
, "%d: %s\n", ssrc
, error
);
251 dev_err(jrdev
, "%d: unknown error source\n", ssrc
);
253 EXPORT_SYMBOL(caam_jr_strstatus
);