watchdog: pic32-dmt: Remove .owner field for driver
[linux/fpc-iii.git] / drivers / crypto / caam / regs.h
blob0ba9c40597dcbbf75163bedb5f4e7ef0f1b46972
1 /*
2 * CAAM hardware register-level view
4 * Copyright 2008-2011 Freescale Semiconductor, Inc.
5 */
7 #ifndef REGS_H
8 #define REGS_H
10 #include <linux/types.h>
11 #include <linux/io.h>
14 * Architecture-specific register access methods
16 * CAAM's bus-addressable registers are 64 bits internally.
17 * They have been wired to be safely accessible on 32-bit
18 * architectures, however. Registers were organized such
19 * that (a) they can be contained in 32 bits, (b) if not, then they
20 * can be treated as two 32-bit entities, or finally (c) if they
21 * must be treated as a single 64-bit value, then this can safely
22 * be done with two 32-bit cycles.
24 * For 32-bit operations on 64-bit values, CAAM follows the same
25 * 64-bit register access conventions as it's predecessors, in that
26 * writes are "triggered" by a write to the register at the numerically
27 * higher address, thus, a full 64-bit write cycle requires a write
28 * to the lower address, followed by a write to the higher address,
29 * which will latch/execute the write cycle.
31 * For example, let's assume a SW reset of CAAM through the master
32 * configuration register.
33 * - SWRST is in bit 31 of MCFG.
34 * - MCFG begins at base+0x0000.
35 * - Bits 63-32 are a 32-bit word at base+0x0000 (numerically-lower)
36 * - Bits 31-0 are a 32-bit word at base+0x0004 (numerically-higher)
38 * (and on Power, the convention is 0-31, 32-63, I know...)
40 * Assuming a 64-bit write to this MCFG to perform a software reset
41 * would then require a write of 0 to base+0x0000, followed by a
42 * write of 0x80000000 to base+0x0004, which would "execute" the
43 * reset.
45 * Of course, since MCFG 63-32 is all zero, we could cheat and simply
46 * write 0x8000000 to base+0x0004, and the reset would work fine.
47 * However, since CAAM does contain some write-and-read-intended
48 * 64-bit registers, this code defines 64-bit access methods for
49 * the sake of internal consistency and simplicity, and so that a
50 * clean transition to 64-bit is possible when it becomes necessary.
52 * There are limitations to this that the developer must recognize.
53 * 32-bit architectures cannot enforce an atomic-64 operation,
54 * Therefore:
56 * - On writes, since the HW is assumed to latch the cycle on the
57 * write of the higher-numeric-address word, then ordered
58 * writes work OK.
60 * - For reads, where a register contains a relevant value of more
61 * that 32 bits, the hardware employs logic to latch the other
62 * "half" of the data until read, ensuring an accurate value.
63 * This is of particular relevance when dealing with CAAM's
64 * performance counters.
68 #ifdef CONFIG_ARM
69 /* These are common macros for Power, put here for ARM */
70 #define setbits32(_addr, _v) writel((readl(_addr) | (_v)), (_addr))
71 #define clrbits32(_addr, _v) writel((readl(_addr) & ~(_v)), (_addr))
73 #define out_arch(type, endian, a, v) __raw_write##type(cpu_to_##endian(v), a)
74 #define in_arch(type, endian, a) endian##_to_cpu(__raw_read##type(a))
76 #define out_le32(a, v) out_arch(l, le32, a, v)
77 #define in_le32(a) in_arch(l, le32, a)
79 #define out_be32(a, v) out_arch(l, be32, a, v)
80 #define in_be32(a) in_arch(l, be32, a)
82 #define clrsetbits(type, addr, clear, set) \
83 out_##type((addr), (in_##type(addr) & ~(clear)) | (set))
85 #define clrsetbits_be32(addr, clear, set) clrsetbits(be32, addr, clear, set)
86 #define clrsetbits_le32(addr, clear, set) clrsetbits(le32, addr, clear, set)
87 #endif
89 #ifdef __BIG_ENDIAN
90 #define wr_reg32(reg, data) out_be32(reg, data)
91 #define rd_reg32(reg) in_be32(reg)
92 #define clrsetbits_32(addr, clear, set) clrsetbits_be32(addr, clear, set)
93 #ifdef CONFIG_64BIT
94 #define wr_reg64(reg, data) out_be64(reg, data)
95 #define rd_reg64(reg) in_be64(reg)
96 #endif
97 #else
98 #ifdef __LITTLE_ENDIAN
99 #define wr_reg32(reg, data) __raw_writel(data, reg)
100 #define rd_reg32(reg) __raw_readl(reg)
101 #define clrsetbits_32(addr, clear, set) clrsetbits_le32(addr, clear, set)
102 #ifdef CONFIG_64BIT
103 #define wr_reg64(reg, data) __raw_writeq(data, reg)
104 #define rd_reg64(reg) __raw_readq(reg)
105 #endif
106 #endif
107 #endif
110 * The only users of these wr/rd_reg64 functions is the Job Ring (JR).
111 * The DMA address registers in the JR are handled differently depending on
112 * platform:
114 * 1. All BE CAAM platforms and i.MX platforms (LE CAAM):
116 * base + 0x0000 : most-significant 32 bits
117 * base + 0x0004 : least-significant 32 bits
119 * The 32-bit version of this core therefore has to write to base + 0x0004
120 * to set the 32-bit wide DMA address.
122 * 2. All other LE CAAM platforms (LS1021A etc.)
123 * base + 0x0000 : least-significant 32 bits
124 * base + 0x0004 : most-significant 32 bits
127 #ifndef CONFIG_64BIT
128 #if !defined(CONFIG_CRYPTO_DEV_FSL_CAAM_LE) || \
129 defined(CONFIG_CRYPTO_DEV_FSL_CAAM_IMX)
130 #define REG64_MS32(reg) ((u32 __iomem *)(reg))
131 #define REG64_LS32(reg) ((u32 __iomem *)(reg) + 1)
132 #else
133 #define REG64_MS32(reg) ((u32 __iomem *)(reg) + 1)
134 #define REG64_LS32(reg) ((u32 __iomem *)(reg))
135 #endif
137 static inline void wr_reg64(u64 __iomem *reg, u64 data)
139 wr_reg32(REG64_MS32(reg), data >> 32);
140 wr_reg32(REG64_LS32(reg), data);
143 static inline u64 rd_reg64(u64 __iomem *reg)
145 return ((u64)rd_reg32(REG64_MS32(reg)) << 32 |
146 (u64)rd_reg32(REG64_LS32(reg)));
148 #endif
151 * jr_outentry
152 * Represents each entry in a JobR output ring
154 struct jr_outentry {
155 dma_addr_t desc;/* Pointer to completed descriptor */
156 u32 jrstatus; /* Status for completed descriptor */
157 } __packed;
160 * caam_perfmon - Performance Monitor/Secure Memory Status/
161 * CAAM Global Status/Component Version IDs
163 * Spans f00-fff wherever instantiated
166 /* Number of DECOs */
167 #define CHA_NUM_MS_DECONUM_SHIFT 24
168 #define CHA_NUM_MS_DECONUM_MASK (0xfull << CHA_NUM_MS_DECONUM_SHIFT)
171 * CHA version IDs / instantiation bitfields
172 * Defined for use with the cha_id fields in perfmon, but the same shift/mask
173 * selectors can be used to pull out the number of instantiated blocks within
174 * cha_num fields in perfmon because the locations are the same.
176 #define CHA_ID_LS_AES_SHIFT 0
177 #define CHA_ID_LS_AES_MASK (0xfull << CHA_ID_LS_AES_SHIFT)
178 #define CHA_ID_LS_AES_LP (0x3ull << CHA_ID_LS_AES_SHIFT)
179 #define CHA_ID_LS_AES_HP (0x4ull << CHA_ID_LS_AES_SHIFT)
181 #define CHA_ID_LS_DES_SHIFT 4
182 #define CHA_ID_LS_DES_MASK (0xfull << CHA_ID_LS_DES_SHIFT)
184 #define CHA_ID_LS_ARC4_SHIFT 8
185 #define CHA_ID_LS_ARC4_MASK (0xfull << CHA_ID_LS_ARC4_SHIFT)
187 #define CHA_ID_LS_MD_SHIFT 12
188 #define CHA_ID_LS_MD_MASK (0xfull << CHA_ID_LS_MD_SHIFT)
189 #define CHA_ID_LS_MD_LP256 (0x0ull << CHA_ID_LS_MD_SHIFT)
190 #define CHA_ID_LS_MD_LP512 (0x1ull << CHA_ID_LS_MD_SHIFT)
191 #define CHA_ID_LS_MD_HP (0x2ull << CHA_ID_LS_MD_SHIFT)
193 #define CHA_ID_LS_RNG_SHIFT 16
194 #define CHA_ID_LS_RNG_MASK (0xfull << CHA_ID_LS_RNG_SHIFT)
196 #define CHA_ID_LS_SNW8_SHIFT 20
197 #define CHA_ID_LS_SNW8_MASK (0xfull << CHA_ID_LS_SNW8_SHIFT)
199 #define CHA_ID_LS_KAS_SHIFT 24
200 #define CHA_ID_LS_KAS_MASK (0xfull << CHA_ID_LS_KAS_SHIFT)
202 #define CHA_ID_LS_PK_SHIFT 28
203 #define CHA_ID_LS_PK_MASK (0xfull << CHA_ID_LS_PK_SHIFT)
205 #define CHA_ID_MS_CRC_SHIFT 0
206 #define CHA_ID_MS_CRC_MASK (0xfull << CHA_ID_MS_CRC_SHIFT)
208 #define CHA_ID_MS_SNW9_SHIFT 4
209 #define CHA_ID_MS_SNW9_MASK (0xfull << CHA_ID_MS_SNW9_SHIFT)
211 #define CHA_ID_MS_DECO_SHIFT 24
212 #define CHA_ID_MS_DECO_MASK (0xfull << CHA_ID_MS_DECO_SHIFT)
214 #define CHA_ID_MS_JR_SHIFT 28
215 #define CHA_ID_MS_JR_MASK (0xfull << CHA_ID_MS_JR_SHIFT)
217 struct sec_vid {
218 u16 ip_id;
219 u8 maj_rev;
220 u8 min_rev;
223 struct caam_perfmon {
224 /* Performance Monitor Registers f00-f9f */
225 u64 req_dequeued; /* PC_REQ_DEQ - Dequeued Requests */
226 u64 ob_enc_req; /* PC_OB_ENC_REQ - Outbound Encrypt Requests */
227 u64 ib_dec_req; /* PC_IB_DEC_REQ - Inbound Decrypt Requests */
228 u64 ob_enc_bytes; /* PC_OB_ENCRYPT - Outbound Bytes Encrypted */
229 u64 ob_prot_bytes; /* PC_OB_PROTECT - Outbound Bytes Protected */
230 u64 ib_dec_bytes; /* PC_IB_DECRYPT - Inbound Bytes Decrypted */
231 u64 ib_valid_bytes; /* PC_IB_VALIDATED Inbound Bytes Validated */
232 u64 rsvd[13];
234 /* CAAM Hardware Instantiation Parameters fa0-fbf */
235 u32 cha_rev_ms; /* CRNR - CHA Rev No. Most significant half*/
236 u32 cha_rev_ls; /* CRNR - CHA Rev No. Least significant half*/
237 #define CTPR_MS_QI_SHIFT 25
238 #define CTPR_MS_QI_MASK (0x1ull << CTPR_MS_QI_SHIFT)
239 #define CTPR_MS_VIRT_EN_INCL 0x00000001
240 #define CTPR_MS_VIRT_EN_POR 0x00000002
241 #define CTPR_MS_PG_SZ_MASK 0x10
242 #define CTPR_MS_PG_SZ_SHIFT 4
243 u32 comp_parms_ms; /* CTPR - Compile Parameters Register */
244 u32 comp_parms_ls; /* CTPR - Compile Parameters Register */
245 u64 rsvd1[2];
247 /* CAAM Global Status fc0-fdf */
248 u64 faultaddr; /* FAR - Fault Address */
249 u32 faultliodn; /* FALR - Fault Address LIODN */
250 u32 faultdetail; /* FADR - Fault Addr Detail */
251 u32 rsvd2;
252 u32 status; /* CSTA - CAAM Status */
253 u64 rsvd3;
255 /* Component Instantiation Parameters fe0-fff */
256 u32 rtic_id; /* RVID - RTIC Version ID */
257 u32 ccb_id; /* CCBVID - CCB Version ID */
258 u32 cha_id_ms; /* CHAVID - CHA Version ID Most Significant*/
259 u32 cha_id_ls; /* CHAVID - CHA Version ID Least Significant*/
260 u32 cha_num_ms; /* CHANUM - CHA Number Most Significant */
261 u32 cha_num_ls; /* CHANUM - CHA Number Least Significant*/
262 u32 caam_id_ms; /* CAAMVID - CAAM Version ID MS */
263 u32 caam_id_ls; /* CAAMVID - CAAM Version ID LS */
266 /* LIODN programming for DMA configuration */
267 #define MSTRID_LOCK_LIODN 0x80000000
268 #define MSTRID_LOCK_MAKETRUSTED 0x00010000 /* only for JR masterid */
270 #define MSTRID_LIODN_MASK 0x0fff
271 struct masterid {
272 u32 liodn_ms; /* lock and make-trusted control bits */
273 u32 liodn_ls; /* LIODN for non-sequence and seq access */
276 /* Partition ID for DMA configuration */
277 struct partid {
278 u32 rsvd1;
279 u32 pidr; /* partition ID, DECO */
282 /* RNGB test mode (replicated twice in some configurations) */
283 /* Padded out to 0x100 */
284 struct rngtst {
285 u32 mode; /* RTSTMODEx - Test mode */
286 u32 rsvd1[3];
287 u32 reset; /* RTSTRESETx - Test reset control */
288 u32 rsvd2[3];
289 u32 status; /* RTSTSSTATUSx - Test status */
290 u32 rsvd3;
291 u32 errstat; /* RTSTERRSTATx - Test error status */
292 u32 rsvd4;
293 u32 errctl; /* RTSTERRCTLx - Test error control */
294 u32 rsvd5;
295 u32 entropy; /* RTSTENTROPYx - Test entropy */
296 u32 rsvd6[15];
297 u32 verifctl; /* RTSTVERIFCTLx - Test verification control */
298 u32 rsvd7;
299 u32 verifstat; /* RTSTVERIFSTATx - Test verification status */
300 u32 rsvd8;
301 u32 verifdata; /* RTSTVERIFDx - Test verification data */
302 u32 rsvd9;
303 u32 xkey; /* RTSTXKEYx - Test XKEY */
304 u32 rsvd10;
305 u32 oscctctl; /* RTSTOSCCTCTLx - Test osc. counter control */
306 u32 rsvd11;
307 u32 oscct; /* RTSTOSCCTx - Test oscillator counter */
308 u32 rsvd12;
309 u32 oscctstat; /* RTSTODCCTSTATx - Test osc counter status */
310 u32 rsvd13[2];
311 u32 ofifo[4]; /* RTSTOFIFOx - Test output FIFO */
312 u32 rsvd14[15];
315 /* RNG4 TRNG test registers */
316 struct rng4tst {
317 #define RTMCTL_PRGM 0x00010000 /* 1 -> program mode, 0 -> run mode */
318 #define RTMCTL_SAMP_MODE_VON_NEUMANN_ES_SC 0 /* use von Neumann data in
319 both entropy shifter and
320 statistical checker */
321 #define RTMCTL_SAMP_MODE_RAW_ES_SC 1 /* use raw data in both
322 entropy shifter and
323 statistical checker */
324 #define RTMCTL_SAMP_MODE_VON_NEUMANN_ES_RAW_SC 2 /* use von Neumann data in
325 entropy shifter, raw data
326 in statistical checker */
327 #define RTMCTL_SAMP_MODE_INVALID 3 /* invalid combination */
328 u32 rtmctl; /* misc. control register */
329 u32 rtscmisc; /* statistical check misc. register */
330 u32 rtpkrrng; /* poker range register */
331 union {
332 u32 rtpkrmax; /* PRGM=1: poker max. limit register */
333 u32 rtpkrsq; /* PRGM=0: poker square calc. result register */
335 #define RTSDCTL_ENT_DLY_SHIFT 16
336 #define RTSDCTL_ENT_DLY_MASK (0xffff << RTSDCTL_ENT_DLY_SHIFT)
337 #define RTSDCTL_ENT_DLY_MIN 3200
338 #define RTSDCTL_ENT_DLY_MAX 12800
339 u32 rtsdctl; /* seed control register */
340 union {
341 u32 rtsblim; /* PRGM=1: sparse bit limit register */
342 u32 rttotsam; /* PRGM=0: total samples register */
344 u32 rtfrqmin; /* frequency count min. limit register */
345 #define RTFRQMAX_DISABLE (1 << 20)
346 union {
347 u32 rtfrqmax; /* PRGM=1: freq. count max. limit register */
348 u32 rtfrqcnt; /* PRGM=0: freq. count register */
350 u32 rsvd1[40];
351 #define RDSTA_SKVT 0x80000000
352 #define RDSTA_SKVN 0x40000000
353 #define RDSTA_IF0 0x00000001
354 #define RDSTA_IF1 0x00000002
355 #define RDSTA_IFMASK (RDSTA_IF1 | RDSTA_IF0)
356 u32 rdsta;
357 u32 rsvd2[15];
361 * caam_ctrl - basic core configuration
362 * starts base + 0x0000 padded out to 0x1000
365 #define KEK_KEY_SIZE 8
366 #define TKEK_KEY_SIZE 8
367 #define TDSK_KEY_SIZE 8
369 #define DECO_RESET 1 /* Use with DECO reset/availability regs */
370 #define DECO_RESET_0 (DECO_RESET << 0)
371 #define DECO_RESET_1 (DECO_RESET << 1)
372 #define DECO_RESET_2 (DECO_RESET << 2)
373 #define DECO_RESET_3 (DECO_RESET << 3)
374 #define DECO_RESET_4 (DECO_RESET << 4)
376 struct caam_ctrl {
377 /* Basic Configuration Section 000-01f */
378 /* Read/Writable */
379 u32 rsvd1;
380 u32 mcr; /* MCFG Master Config Register */
381 u32 rsvd2;
382 u32 scfgr; /* SCFGR, Security Config Register */
384 /* Bus Access Configuration Section 010-11f */
385 /* Read/Writable */
386 struct masterid jr_mid[4]; /* JRxLIODNR - JobR LIODN setup */
387 u32 rsvd3[11];
388 u32 jrstart; /* JRSTART - Job Ring Start Register */
389 struct masterid rtic_mid[4]; /* RTICxLIODNR - RTIC LIODN setup */
390 u32 rsvd4[5];
391 u32 deco_rsr; /* DECORSR - Deco Request Source */
392 u32 rsvd11;
393 u32 deco_rq; /* DECORR - DECO Request */
394 struct partid deco_mid[5]; /* DECOxLIODNR - 1 per DECO */
395 u32 rsvd5[22];
397 /* DECO Availability/Reset Section 120-3ff */
398 u32 deco_avail; /* DAR - DECO availability */
399 u32 deco_reset; /* DRR - DECO reset */
400 u32 rsvd6[182];
402 /* Key Encryption/Decryption Configuration 400-5ff */
403 /* Read/Writable only while in Non-secure mode */
404 u32 kek[KEK_KEY_SIZE]; /* JDKEKR - Key Encryption Key */
405 u32 tkek[TKEK_KEY_SIZE]; /* TDKEKR - Trusted Desc KEK */
406 u32 tdsk[TDSK_KEY_SIZE]; /* TDSKR - Trusted Desc Signing Key */
407 u32 rsvd7[32];
408 u64 sknonce; /* SKNR - Secure Key Nonce */
409 u32 rsvd8[70];
411 /* RNG Test/Verification/Debug Access 600-7ff */
412 /* (Useful in Test/Debug modes only...) */
413 union {
414 struct rngtst rtst[2];
415 struct rng4tst r4tst[2];
418 u32 rsvd9[448];
420 /* Performance Monitor f00-fff */
421 struct caam_perfmon perfmon;
425 * Controller master config register defs
427 #define MCFGR_SWRESET 0x80000000 /* software reset */
428 #define MCFGR_WDENABLE 0x40000000 /* DECO watchdog enable */
429 #define MCFGR_WDFAIL 0x20000000 /* DECO watchdog force-fail */
430 #define MCFGR_DMA_RESET 0x10000000
431 #define MCFGR_LONG_PTR 0x00010000 /* Use >32-bit desc addressing */
432 #define SCFGR_RDBENABLE 0x00000400
433 #define SCFGR_VIRT_EN 0x00008000
434 #define DECORR_RQD0ENABLE 0x00000001 /* Enable DECO0 for direct access */
435 #define DECORSR_JR0 0x00000001 /* JR to supply TZ, SDID, ICID */
436 #define DECORSR_VALID 0x80000000
437 #define DECORR_DEN0 0x00010000 /* DECO0 available for access*/
439 /* AXI read cache control */
440 #define MCFGR_ARCACHE_SHIFT 12
441 #define MCFGR_ARCACHE_MASK (0xf << MCFGR_ARCACHE_SHIFT)
442 #define MCFGR_ARCACHE_BUFF (0x1 << MCFGR_ARCACHE_SHIFT)
443 #define MCFGR_ARCACHE_CACH (0x2 << MCFGR_ARCACHE_SHIFT)
444 #define MCFGR_ARCACHE_RALL (0x4 << MCFGR_ARCACHE_SHIFT)
446 /* AXI write cache control */
447 #define MCFGR_AWCACHE_SHIFT 8
448 #define MCFGR_AWCACHE_MASK (0xf << MCFGR_AWCACHE_SHIFT)
449 #define MCFGR_AWCACHE_BUFF (0x1 << MCFGR_AWCACHE_SHIFT)
450 #define MCFGR_AWCACHE_CACH (0x2 << MCFGR_AWCACHE_SHIFT)
451 #define MCFGR_AWCACHE_WALL (0x8 << MCFGR_AWCACHE_SHIFT)
453 /* AXI pipeline depth */
454 #define MCFGR_AXIPIPE_SHIFT 4
455 #define MCFGR_AXIPIPE_MASK (0xf << MCFGR_AXIPIPE_SHIFT)
457 #define MCFGR_AXIPRI 0x00000008 /* Assert AXI priority sideband */
458 #define MCFGR_LARGE_BURST 0x00000004 /* 128/256-byte burst size */
459 #define MCFGR_BURST_64 0x00000001 /* 64-byte burst size */
461 /* JRSTART register offsets */
462 #define JRSTART_JR0_START 0x00000001 /* Start Job ring 0 */
463 #define JRSTART_JR1_START 0x00000002 /* Start Job ring 1 */
464 #define JRSTART_JR2_START 0x00000004 /* Start Job ring 2 */
465 #define JRSTART_JR3_START 0x00000008 /* Start Job ring 3 */
468 * caam_job_ring - direct job ring setup
469 * 1-4 possible per instantiation, base + 1000/2000/3000/4000
470 * Padded out to 0x1000
472 struct caam_job_ring {
473 /* Input ring */
474 u64 inpring_base; /* IRBAx - Input desc ring baseaddr */
475 u32 rsvd1;
476 u32 inpring_size; /* IRSx - Input ring size */
477 u32 rsvd2;
478 u32 inpring_avail; /* IRSAx - Input ring room remaining */
479 u32 rsvd3;
480 u32 inpring_jobadd; /* IRJAx - Input ring jobs added */
482 /* Output Ring */
483 u64 outring_base; /* ORBAx - Output status ring base addr */
484 u32 rsvd4;
485 u32 outring_size; /* ORSx - Output ring size */
486 u32 rsvd5;
487 u32 outring_rmvd; /* ORJRx - Output ring jobs removed */
488 u32 rsvd6;
489 u32 outring_used; /* ORSFx - Output ring slots full */
491 /* Status/Configuration */
492 u32 rsvd7;
493 u32 jroutstatus; /* JRSTAx - JobR output status */
494 u32 rsvd8;
495 u32 jrintstatus; /* JRINTx - JobR interrupt status */
496 u32 rconfig_hi; /* JRxCFG - Ring configuration */
497 u32 rconfig_lo;
499 /* Indices. CAAM maintains as "heads" of each queue */
500 u32 rsvd9;
501 u32 inp_rdidx; /* IRRIx - Input ring read index */
502 u32 rsvd10;
503 u32 out_wtidx; /* ORWIx - Output ring write index */
505 /* Command/control */
506 u32 rsvd11;
507 u32 jrcommand; /* JRCRx - JobR command */
509 u32 rsvd12[932];
511 /* Performance Monitor f00-fff */
512 struct caam_perfmon perfmon;
515 #define JR_RINGSIZE_MASK 0x03ff
517 * jrstatus - Job Ring Output Status
518 * All values in lo word
519 * Also note, same values written out as status through QI
520 * in the command/status field of a frame descriptor
522 #define JRSTA_SSRC_SHIFT 28
523 #define JRSTA_SSRC_MASK 0xf0000000
525 #define JRSTA_SSRC_NONE 0x00000000
526 #define JRSTA_SSRC_CCB_ERROR 0x20000000
527 #define JRSTA_SSRC_JUMP_HALT_USER 0x30000000
528 #define JRSTA_SSRC_DECO 0x40000000
529 #define JRSTA_SSRC_JRERROR 0x60000000
530 #define JRSTA_SSRC_JUMP_HALT_CC 0x70000000
532 #define JRSTA_DECOERR_JUMP 0x08000000
533 #define JRSTA_DECOERR_INDEX_SHIFT 8
534 #define JRSTA_DECOERR_INDEX_MASK 0xff00
535 #define JRSTA_DECOERR_ERROR_MASK 0x00ff
537 #define JRSTA_DECOERR_NONE 0x00
538 #define JRSTA_DECOERR_LINKLEN 0x01
539 #define JRSTA_DECOERR_LINKPTR 0x02
540 #define JRSTA_DECOERR_JRCTRL 0x03
541 #define JRSTA_DECOERR_DESCCMD 0x04
542 #define JRSTA_DECOERR_ORDER 0x05
543 #define JRSTA_DECOERR_KEYCMD 0x06
544 #define JRSTA_DECOERR_LOADCMD 0x07
545 #define JRSTA_DECOERR_STORECMD 0x08
546 #define JRSTA_DECOERR_OPCMD 0x09
547 #define JRSTA_DECOERR_FIFOLDCMD 0x0a
548 #define JRSTA_DECOERR_FIFOSTCMD 0x0b
549 #define JRSTA_DECOERR_MOVECMD 0x0c
550 #define JRSTA_DECOERR_JUMPCMD 0x0d
551 #define JRSTA_DECOERR_MATHCMD 0x0e
552 #define JRSTA_DECOERR_SHASHCMD 0x0f
553 #define JRSTA_DECOERR_SEQCMD 0x10
554 #define JRSTA_DECOERR_DECOINTERNAL 0x11
555 #define JRSTA_DECOERR_SHDESCHDR 0x12
556 #define JRSTA_DECOERR_HDRLEN 0x13
557 #define JRSTA_DECOERR_BURSTER 0x14
558 #define JRSTA_DECOERR_DESCSIGNATURE 0x15
559 #define JRSTA_DECOERR_DMA 0x16
560 #define JRSTA_DECOERR_BURSTFIFO 0x17
561 #define JRSTA_DECOERR_JRRESET 0x1a
562 #define JRSTA_DECOERR_JOBFAIL 0x1b
563 #define JRSTA_DECOERR_DNRERR 0x80
564 #define JRSTA_DECOERR_UNDEFPCL 0x81
565 #define JRSTA_DECOERR_PDBERR 0x82
566 #define JRSTA_DECOERR_ANRPLY_LATE 0x83
567 #define JRSTA_DECOERR_ANRPLY_REPLAY 0x84
568 #define JRSTA_DECOERR_SEQOVF 0x85
569 #define JRSTA_DECOERR_INVSIGN 0x86
570 #define JRSTA_DECOERR_DSASIGN 0x87
572 #define JRSTA_CCBERR_JUMP 0x08000000
573 #define JRSTA_CCBERR_INDEX_MASK 0xff00
574 #define JRSTA_CCBERR_INDEX_SHIFT 8
575 #define JRSTA_CCBERR_CHAID_MASK 0x00f0
576 #define JRSTA_CCBERR_CHAID_SHIFT 4
577 #define JRSTA_CCBERR_ERRID_MASK 0x000f
579 #define JRSTA_CCBERR_CHAID_AES (0x01 << JRSTA_CCBERR_CHAID_SHIFT)
580 #define JRSTA_CCBERR_CHAID_DES (0x02 << JRSTA_CCBERR_CHAID_SHIFT)
581 #define JRSTA_CCBERR_CHAID_ARC4 (0x03 << JRSTA_CCBERR_CHAID_SHIFT)
582 #define JRSTA_CCBERR_CHAID_MD (0x04 << JRSTA_CCBERR_CHAID_SHIFT)
583 #define JRSTA_CCBERR_CHAID_RNG (0x05 << JRSTA_CCBERR_CHAID_SHIFT)
584 #define JRSTA_CCBERR_CHAID_SNOW (0x06 << JRSTA_CCBERR_CHAID_SHIFT)
585 #define JRSTA_CCBERR_CHAID_KASUMI (0x07 << JRSTA_CCBERR_CHAID_SHIFT)
586 #define JRSTA_CCBERR_CHAID_PK (0x08 << JRSTA_CCBERR_CHAID_SHIFT)
587 #define JRSTA_CCBERR_CHAID_CRC (0x09 << JRSTA_CCBERR_CHAID_SHIFT)
589 #define JRSTA_CCBERR_ERRID_NONE 0x00
590 #define JRSTA_CCBERR_ERRID_MODE 0x01
591 #define JRSTA_CCBERR_ERRID_DATASIZ 0x02
592 #define JRSTA_CCBERR_ERRID_KEYSIZ 0x03
593 #define JRSTA_CCBERR_ERRID_PKAMEMSZ 0x04
594 #define JRSTA_CCBERR_ERRID_PKBMEMSZ 0x05
595 #define JRSTA_CCBERR_ERRID_SEQUENCE 0x06
596 #define JRSTA_CCBERR_ERRID_PKDIVZRO 0x07
597 #define JRSTA_CCBERR_ERRID_PKMODEVN 0x08
598 #define JRSTA_CCBERR_ERRID_KEYPARIT 0x09
599 #define JRSTA_CCBERR_ERRID_ICVCHK 0x0a
600 #define JRSTA_CCBERR_ERRID_HARDWARE 0x0b
601 #define JRSTA_CCBERR_ERRID_CCMAAD 0x0c
602 #define JRSTA_CCBERR_ERRID_INVCHA 0x0f
604 #define JRINT_ERR_INDEX_MASK 0x3fff0000
605 #define JRINT_ERR_INDEX_SHIFT 16
606 #define JRINT_ERR_TYPE_MASK 0xf00
607 #define JRINT_ERR_TYPE_SHIFT 8
608 #define JRINT_ERR_HALT_MASK 0xc
609 #define JRINT_ERR_HALT_SHIFT 2
610 #define JRINT_ERR_HALT_INPROGRESS 0x4
611 #define JRINT_ERR_HALT_COMPLETE 0x8
612 #define JRINT_JR_ERROR 0x02
613 #define JRINT_JR_INT 0x01
615 #define JRINT_ERR_TYPE_WRITE 1
616 #define JRINT_ERR_TYPE_BAD_INPADDR 3
617 #define JRINT_ERR_TYPE_BAD_OUTADDR 4
618 #define JRINT_ERR_TYPE_INV_INPWRT 5
619 #define JRINT_ERR_TYPE_INV_OUTWRT 6
620 #define JRINT_ERR_TYPE_RESET 7
621 #define JRINT_ERR_TYPE_REMOVE_OFL 8
622 #define JRINT_ERR_TYPE_ADD_OFL 9
624 #define JRCFG_SOE 0x04
625 #define JRCFG_ICEN 0x02
626 #define JRCFG_IMSK 0x01
627 #define JRCFG_ICDCT_SHIFT 8
628 #define JRCFG_ICTT_SHIFT 16
630 #define JRCR_RESET 0x01
633 * caam_assurance - Assurance Controller View
634 * base + 0x6000 padded out to 0x1000
637 struct rtic_element {
638 u64 address;
639 u32 rsvd;
640 u32 length;
643 struct rtic_block {
644 struct rtic_element element[2];
647 struct rtic_memhash {
648 u32 memhash_be[32];
649 u32 memhash_le[32];
652 struct caam_assurance {
653 /* Status/Command/Watchdog */
654 u32 rsvd1;
655 u32 status; /* RSTA - Status */
656 u32 rsvd2;
657 u32 cmd; /* RCMD - Command */
658 u32 rsvd3;
659 u32 ctrl; /* RCTL - Control */
660 u32 rsvd4;
661 u32 throttle; /* RTHR - Throttle */
662 u32 rsvd5[2];
663 u64 watchdog; /* RWDOG - Watchdog Timer */
664 u32 rsvd6;
665 u32 rend; /* REND - Endian corrections */
666 u32 rsvd7[50];
668 /* Block access/configuration @ 100/110/120/130 */
669 struct rtic_block memblk[4]; /* Memory Blocks A-D */
670 u32 rsvd8[32];
672 /* Block hashes @ 200/300/400/500 */
673 struct rtic_memhash hash[4]; /* Block hash values A-D */
674 u32 rsvd_3[640];
678 * caam_queue_if - QI configuration and control
679 * starts base + 0x7000, padded out to 0x1000 long
682 struct caam_queue_if {
683 u32 qi_control_hi; /* QICTL - QI Control */
684 u32 qi_control_lo;
685 u32 rsvd1;
686 u32 qi_status; /* QISTA - QI Status */
687 u32 qi_deq_cfg_hi; /* QIDQC - QI Dequeue Configuration */
688 u32 qi_deq_cfg_lo;
689 u32 qi_enq_cfg_hi; /* QISEQC - QI Enqueue Command */
690 u32 qi_enq_cfg_lo;
691 u32 rsvd2[1016];
694 /* QI control bits - low word */
695 #define QICTL_DQEN 0x01 /* Enable frame pop */
696 #define QICTL_STOP 0x02 /* Stop dequeue/enqueue */
697 #define QICTL_SOE 0x04 /* Stop on error */
699 /* QI control bits - high word */
700 #define QICTL_MBSI 0x01
701 #define QICTL_MHWSI 0x02
702 #define QICTL_MWSI 0x04
703 #define QICTL_MDWSI 0x08
704 #define QICTL_CBSI 0x10 /* CtrlDataByteSwapInput */
705 #define QICTL_CHWSI 0x20 /* CtrlDataHalfSwapInput */
706 #define QICTL_CWSI 0x40 /* CtrlDataWordSwapInput */
707 #define QICTL_CDWSI 0x80 /* CtrlDataDWordSwapInput */
708 #define QICTL_MBSO 0x0100
709 #define QICTL_MHWSO 0x0200
710 #define QICTL_MWSO 0x0400
711 #define QICTL_MDWSO 0x0800
712 #define QICTL_CBSO 0x1000 /* CtrlDataByteSwapOutput */
713 #define QICTL_CHWSO 0x2000 /* CtrlDataHalfSwapOutput */
714 #define QICTL_CWSO 0x4000 /* CtrlDataWordSwapOutput */
715 #define QICTL_CDWSO 0x8000 /* CtrlDataDWordSwapOutput */
716 #define QICTL_DMBS 0x010000
717 #define QICTL_EPO 0x020000
719 /* QI status bits */
720 #define QISTA_PHRDERR 0x01 /* PreHeader Read Error */
721 #define QISTA_CFRDERR 0x02 /* Compound Frame Read Error */
722 #define QISTA_OFWRERR 0x04 /* Output Frame Read Error */
723 #define QISTA_BPDERR 0x08 /* Buffer Pool Depleted */
724 #define QISTA_BTSERR 0x10 /* Buffer Undersize */
725 #define QISTA_CFWRERR 0x20 /* Compound Frame Write Err */
726 #define QISTA_STOPD 0x80000000 /* QI Stopped (see QICTL) */
728 /* deco_sg_table - DECO view of scatter/gather table */
729 struct deco_sg_table {
730 u64 addr; /* Segment Address */
731 u32 elen; /* E, F bits + 30-bit length */
732 u32 bpid_offset; /* Buffer Pool ID + 16-bit length */
736 * caam_deco - descriptor controller - CHA cluster block
738 * Only accessible when direct DECO access is turned on
739 * (done in DECORR, via MID programmed in DECOxMID
741 * 5 typical, base + 0x8000/9000/a000/b000
742 * Padded out to 0x1000 long
744 struct caam_deco {
745 u32 rsvd1;
746 u32 cls1_mode; /* CxC1MR - Class 1 Mode */
747 u32 rsvd2;
748 u32 cls1_keysize; /* CxC1KSR - Class 1 Key Size */
749 u32 cls1_datasize_hi; /* CxC1DSR - Class 1 Data Size */
750 u32 cls1_datasize_lo;
751 u32 rsvd3;
752 u32 cls1_icvsize; /* CxC1ICVSR - Class 1 ICV size */
753 u32 rsvd4[5];
754 u32 cha_ctrl; /* CCTLR - CHA control */
755 u32 rsvd5;
756 u32 irq_crtl; /* CxCIRQ - CCB interrupt done/error/clear */
757 u32 rsvd6;
758 u32 clr_written; /* CxCWR - Clear-Written */
759 u32 ccb_status_hi; /* CxCSTA - CCB Status/Error */
760 u32 ccb_status_lo;
761 u32 rsvd7[3];
762 u32 aad_size; /* CxAADSZR - Current AAD Size */
763 u32 rsvd8;
764 u32 cls1_iv_size; /* CxC1IVSZR - Current Class 1 IV Size */
765 u32 rsvd9[7];
766 u32 pkha_a_size; /* PKASZRx - Size of PKHA A */
767 u32 rsvd10;
768 u32 pkha_b_size; /* PKBSZRx - Size of PKHA B */
769 u32 rsvd11;
770 u32 pkha_n_size; /* PKNSZRx - Size of PKHA N */
771 u32 rsvd12;
772 u32 pkha_e_size; /* PKESZRx - Size of PKHA E */
773 u32 rsvd13[24];
774 u32 cls1_ctx[16]; /* CxC1CTXR - Class 1 Context @100 */
775 u32 rsvd14[48];
776 u32 cls1_key[8]; /* CxC1KEYR - Class 1 Key @200 */
777 u32 rsvd15[121];
778 u32 cls2_mode; /* CxC2MR - Class 2 Mode */
779 u32 rsvd16;
780 u32 cls2_keysize; /* CxX2KSR - Class 2 Key Size */
781 u32 cls2_datasize_hi; /* CxC2DSR - Class 2 Data Size */
782 u32 cls2_datasize_lo;
783 u32 rsvd17;
784 u32 cls2_icvsize; /* CxC2ICVSZR - Class 2 ICV Size */
785 u32 rsvd18[56];
786 u32 cls2_ctx[18]; /* CxC2CTXR - Class 2 Context @500 */
787 u32 rsvd19[46];
788 u32 cls2_key[32]; /* CxC2KEYR - Class2 Key @600 */
789 u32 rsvd20[84];
790 u32 inp_infofifo_hi; /* CxIFIFO - Input Info FIFO @7d0 */
791 u32 inp_infofifo_lo;
792 u32 rsvd21[2];
793 u64 inp_datafifo; /* CxDFIFO - Input Data FIFO */
794 u32 rsvd22[2];
795 u64 out_datafifo; /* CxOFIFO - Output Data FIFO */
796 u32 rsvd23[2];
797 u32 jr_ctl_hi; /* CxJRR - JobR Control Register @800 */
798 u32 jr_ctl_lo;
799 u64 jr_descaddr; /* CxDADR - JobR Descriptor Address */
800 #define DECO_OP_STATUS_HI_ERR_MASK 0xF00000FF
801 u32 op_status_hi; /* DxOPSTA - DECO Operation Status */
802 u32 op_status_lo;
803 u32 rsvd24[2];
804 u32 liodn; /* DxLSR - DECO LIODN Status - non-seq */
805 u32 td_liodn; /* DxLSR - DECO LIODN Status - trustdesc */
806 u32 rsvd26[6];
807 u64 math[4]; /* DxMTH - Math register */
808 u32 rsvd27[8];
809 struct deco_sg_table gthr_tbl[4]; /* DxGTR - Gather Tables */
810 u32 rsvd28[16];
811 struct deco_sg_table sctr_tbl[4]; /* DxSTR - Scatter Tables */
812 u32 rsvd29[48];
813 u32 descbuf[64]; /* DxDESB - Descriptor buffer */
814 u32 rscvd30[193];
815 #define DESC_DBG_DECO_STAT_HOST_ERR 0x00D00000
816 #define DESC_DBG_DECO_STAT_VALID 0x80000000
817 #define DESC_DBG_DECO_STAT_MASK 0x00F00000
818 u32 desc_dbg; /* DxDDR - DECO Debug Register */
819 u32 rsvd31[126];
822 #define DECO_JQCR_WHL 0x20000000
823 #define DECO_JQCR_FOUR 0x10000000
825 #define JR_BLOCK_NUMBER 1
826 #define ASSURE_BLOCK_NUMBER 6
827 #define QI_BLOCK_NUMBER 7
828 #define DECO_BLOCK_NUMBER 8
829 #define PG_SIZE_4K 0x1000
830 #define PG_SIZE_64K 0x10000
831 #endif /* REGS_H */