| blob | 05ad8c98e52721e23a12f72a1221bc4004e4d148 |
1 /*
2 * MPC8323E EMDS Device Tree Source
3 *
4 * Copyright 2006 Freescale Semiconductor Inc.
5 *
6 * This program is free software; you can redistribute it and/or modify it
7 * under the terms of the GNU General Public License as published by the
8 * Free Software Foundation; either version 2 of the License, or (at your
9 * option) any later version.
11 * To enable external serial I/O on a Freescale MPC 8323 SYS/MDS board, do
12 * this:
13 *
14 * 1) On chip U61, lift (disconnect) pins 21 (TXD) and 22 (RXD) from the board.
15 * 2) Solder a wire from U61-21 to P19A-23. P19 is a grid of pins on the board
16 * next to the serial ports.
17 * 3) Solder a wire from U61-22 to P19K-22.
18 *
19 * Note that there's a typo in the schematic. The board labels the last column
20 * of pins "P19K", but in the schematic, that column is called "P19J". So if
21 * you're going by the schematic, the pin is called "P19J-K22".
22 */
24 /dts-v1/;
26 / {
27 model = "MPC8323EMDS";
28 compatible = "MPC8323EMDS", "MPC832xMDS", "MPC83xxMDS";
29 #address-cells = <1>;
30 #size-cells = <1>;
32 aliases {
33 ethernet0 = &enet0;
34 ethernet1 = &enet1;
35 serial0 = &serial0;
36 serial1 = &serial1;
37 pci0 = &pci0;
38 };
40 cpus {
41 #address-cells = <1>;
42 #size-cells = <0>;
44 PowerPC,8323@0 {
45 device_type = "cpu";
46 reg = <0x0>;
47 d-cache-line-size = <32>; // 32 bytes
48 i-cache-line-size = <32>; // 32 bytes
49 d-cache-size = <16384>; // L1, 16K
50 i-cache-size = <16384>; // L1, 16K
51 timebase-frequency = <0>;
52 bus-frequency = <0>;
53 clock-frequency = <0>;
54 };
55 };
57 memory {
58 device_type = "memory";
59 reg = <0x00000000 0x08000000>;
60 };
62 bcsr@f8000000 {
63 compatible = "fsl,mpc8323mds-bcsr";
64 reg = <0xf8000000 0x8000>;
65 };
67 soc8323@e0000000 {
68 #address-cells = <1>;
69 #size-cells = <1>;
70 device_type = "soc";
71 compatible = "simple-bus";
72 ranges = <0x0 0xe0000000 0x00100000>;
73 reg = <0xe0000000 0x00000200>;
74 bus-frequency = <132000000>;
76 wdt@200 {
77 device_type = "watchdog";
78 compatible = "mpc83xx_wdt";
79 reg = <0x200 0x100>;
80 };
82 pmc: power@b00 {
83 compatible = "fsl,mpc8323-pmc", "fsl,mpc8349-pmc";
84 reg = <0xb00 0x100 0xa00 0x100>;
85 interrupts = <80 0x8>;
86 interrupt-parent = <&ipic>;
87 };
89 i2c@3000 {
90 #address-cells = <1>;
91 #size-cells = <0>;
92 cell-index = <0>;
93 compatible = "fsl-i2c";
94 reg = <0x3000 0x100>;
95 interrupts = <14 0x8>;
96 interrupt-parent = <&ipic>;
97 dfsrr;
99 rtc@68 {
100 compatible = "dallas,ds1374";
101 reg = <0x68>;
102 };
103 };
105 serial0: serial@4500 {
106 cell-index = <0>;
107 device_type = "serial";
108 compatible = "ns16550";
109 reg = <0x4500 0x100>;
110 clock-frequency = <0>;
111 interrupts = <9 0x8>;
112 interrupt-parent = <&ipic>;
113 };
115 serial1: serial@4600 {
116 cell-index = <1>;
117 device_type = "serial";
118 compatible = "ns16550";
119 reg = <0x4600 0x100>;
120 clock-frequency = <0>;
121 interrupts = <10 0x8>;
122 interrupt-parent = <&ipic>;
123 };
125 dma@82a8 {
126 #address-cells = <1>;
127 #size-cells = <1>;
128 compatible = "fsl,mpc8323-dma", "fsl,elo-dma";
129 reg = <0x82a8 4>;
130 ranges = <0 0x8100 0x1a8>;
131 interrupt-parent = <&ipic>;
132 interrupts = <71 8>;
133 cell-index = <0>;
134 dma-channel@0 {
135 compatible = "fsl,mpc8323-dma-channel", "fsl,elo-dma-channel";
136 reg = <0 0x80>;
137 cell-index = <0>;
138 interrupt-parent = <&ipic>;
139 interrupts = <71 8>;
140 };
141 dma-channel@80 {
142 compatible = "fsl,mpc8323-dma-channel", "fsl,elo-dma-channel";
143 reg = <0x80 0x80>;
144 cell-index = <1>;
145 interrupt-parent = <&ipic>;
146 interrupts = <71 8>;
147 };
148 dma-channel@100 {
149 compatible = "fsl,mpc8323-dma-channel", "fsl,elo-dma-channel";
150 reg = <0x100 0x80>;
151 cell-index = <2>;
152 interrupt-parent = <&ipic>;
153 interrupts = <71 8>;
154 };
155 dma-channel@180 {
156 compatible = "fsl,mpc8323-dma-channel", "fsl,elo-dma-channel";
157 reg = <0x180 0x28>;
158 cell-index = <3>;
159 interrupt-parent = <&ipic>;
160 interrupts = <71 8>;
161 };
162 };
164 crypto@30000 {
165 compatible = "fsl,sec2.2", "fsl,sec2.1", "fsl,sec2.0";
166 reg = <0x30000 0x10000>;
167 interrupts = <11 0x8>;
168 interrupt-parent = <&ipic>;
169 fsl,num-channels = <1>;
170 fsl,channel-fifo-len = <24>;
171 fsl,exec-units-mask = <0x4c>;
172 fsl,descriptor-types-mask = <0x0122003f>;
173 sleep = <&pmc 0x03000000>;
174 };
176 ipic: pic@700 {
177 interrupt-controller;
178 #address-cells = <0>;
179 #interrupt-cells = <2>;
180 reg = <0x700 0x100>;
181 device_type = "ipic";
182 };
184 par_io@1400 {
185 reg = <0x1400 0x100>;
186 device_type = "par_io";
187 num-ports = <7>;
189 pio3: ucc_pin@03 {
190 pio-map = <
191 /* port pin dir open_drain assignment has_irq */
192 3 4 3 0 2 0 /* MDIO */
193 3 5 1 0 2 0 /* MDC */
194 0 13 2 0 1 0 /* RX_CLK (CLK9) */
195 3 24 2 0 1 0 /* TX_CLK (CLK10) */
196 1 0 1 0 1 0 /* TxD0 */
197 1 1 1 0 1 0 /* TxD1 */
198 1 2 1 0 1 0 /* TxD2 */
199 1 3 1 0 1 0 /* TxD3 */
200 1 4 2 0 1 0 /* RxD0 */
201 1 5 2 0 1 0 /* RxD1 */
202 1 6 2 0 1 0 /* RxD2 */
203 1 7 2 0 1 0 /* RxD3 */
204 1 8 2 0 1 0 /* RX_ER */
205 1 9 1 0 1 0 /* TX_ER */
206 1 10 2 0 1 0 /* RX_DV */
207 1 11 2 0 1 0 /* COL */
208 1 12 1 0 1 0 /* TX_EN */
209 1 13 2 0 1 0>; /* CRS */
210 };
211 pio4: ucc_pin@04 {
212 pio-map = <
213 /* port pin dir open_drain assignment has_irq */
214 3 31 2 0 1 0 /* RX_CLK (CLK7) */
215 3 6 2 0 1 0 /* TX_CLK (CLK8) */
216 1 18 1 0 1 0 /* TxD0 */
217 1 19 1 0 1 0 /* TxD1 */
218 1 20 1 0 1 0 /* TxD2 */
219 1 21 1 0 1 0 /* TxD3 */
220 1 22 2 0 1 0 /* RxD0 */
221 1 23 2 0 1 0 /* RxD1 */
222 1 24 2 0 1 0 /* RxD2 */
223 1 25 2 0 1 0 /* RxD3 */
224 1 26 2 0 1 0 /* RX_ER */
225 1 27 1 0 1 0 /* TX_ER */
226 1 28 2 0 1 0 /* RX_DV */
227 1 29 2 0 1 0 /* COL */
228 1 30 1 0 1 0 /* TX_EN */
229 1 31 2 0 1 0>; /* CRS */
230 };
231 pio5: ucc_pin@05 {
232 pio-map = <
233 /*
234 * open has
235 * port pin dir drain sel irq
236 */
237 2 0 1 0 2 0 /* TxD5 */
238 2 8 2 0 2 0 /* RxD5 */
240 2 29 2 0 0 0 /* CTS5 */
241 2 31 1 0 2 0 /* RTS5 */
243 2 24 2 0 0 0 /* CD */
245 >;
246 };
248 };
249 };
251 qe@e0100000 {
252 #address-cells = <1>;
253 #size-cells = <1>;
254 device_type = "qe";
255 compatible = "fsl,qe";
256 ranges = <0x0 0xe0100000 0x00100000>;
257 reg = <0xe0100000 0x480>;
258 brg-frequency = <0>;
259 bus-frequency = <198000000>;
260 fsl,qe-num-riscs = <1>;
261 fsl,qe-num-snums = <28>;
263 muram@10000 {
264 #address-cells = <1>;
265 #size-cells = <1>;
266 compatible = "fsl,qe-muram", "fsl,cpm-muram";
267 ranges = <0x0 0x00010000 0x00004000>;
269 data-only@0 {
270 compatible = "fsl,qe-muram-data",
271 "fsl,cpm-muram-data";
272 reg = <0x0 0x4000>;
273 };
274 };
276 spi@4c0 {
277 cell-index = <0>;
278 compatible = "fsl,spi";
279 reg = <0x4c0 0x40>;
280 interrupts = <2>;
281 interrupt-parent = <&qeic>;
282 mode = "cpu";
283 };
285 spi@500 {
286 cell-index = <1>;
287 compatible = "fsl,spi";
288 reg = <0x500 0x40>;
289 interrupts = <1>;
290 interrupt-parent = <&qeic>;
291 mode = "cpu";
292 };
294 usb@6c0 {
295 compatible = "qe_udc";
296 reg = <0x6c0 0x40 0x8b00 0x100>;
297 interrupts = <11>;
298 interrupt-parent = <&qeic>;
299 mode = "slave";
300 };
302 enet0: ucc@2200 {
303 device_type = "network";
304 compatible = "ucc_geth";
305 cell-index = <3>;
306 reg = <0x2200 0x200>;
307 interrupts = <34>;
308 interrupt-parent = <&qeic>;
309 local-mac-address = [ 00 00 00 00 00 00 ];
310 rx-clock-name = "clk9";
311 tx-clock-name = "clk10";
312 phy-handle = <&phy3>;
313 pio-handle = <&pio3>;
314 };
316 enet1: ucc@3200 {
317 device_type = "network";
318 compatible = "ucc_geth";
319 cell-index = <4>;
320 reg = <0x3200 0x200>;
321 interrupts = <35>;
322 interrupt-parent = <&qeic>;
323 local-mac-address = [ 00 00 00 00 00 00 ];
324 rx-clock-name = "clk7";
325 tx-clock-name = "clk8";
326 phy-handle = <&phy4>;
327 pio-handle = <&pio4>;
328 };
330 ucc@2400 {
331 device_type = "serial";
332 compatible = "ucc_uart";
333 cell-index = <5>; /* The UCC number, 1-7*/
334 port-number = <0>; /* Which ttyQEx device */
335 soft-uart; /* We need Soft-UART */
336 reg = <0x2400 0x200>;
337 interrupts = <40>; /* From Table 18-12 */
338 interrupt-parent = < &qeic >;
339 /*
340 * For Soft-UART, we need to set TX to 1X, which
341 * means specifying separate clock sources.
342 */
343 rx-clock-name = "brg5";
344 tx-clock-name = "brg6";
345 pio-handle = < &pio5 >;
346 };
349 mdio@2320 {
350 #address-cells = <1>;
351 #size-cells = <0>;
352 reg = <0x2320 0x18>;
353 compatible = "fsl,ucc-mdio";
355 phy3: ethernet-phy@03 {
356 interrupt-parent = <&ipic>;
357 interrupts = <17 0x8>;
358 reg = <0x3>;
359 device_type = "ethernet-phy";
360 };
361 phy4: ethernet-phy@04 {
362 interrupt-parent = <&ipic>;
363 interrupts = <18 0x8>;
364 reg = <0x4>;
365 device_type = "ethernet-phy";
366 };
367 };
369 qeic: interrupt-controller@80 {
370 interrupt-controller;
371 compatible = "fsl,qe-ic";
372 #address-cells = <0>;
373 #interrupt-cells = <1>;
374 reg = <0x80 0x80>;
375 big-endian;
376 interrupts = <32 0x8 33 0x8>; //high:32 low:33
377 interrupt-parent = <&ipic>;
378 };
379 };
381 pci0: pci@e0008500 {
382 interrupt-map-mask = <0xf800 0x0 0x0 0x7>;
383 interrupt-map = <
384 /* IDSEL 0x11 AD17 */
385 0x8800 0x0 0x0 0x1 &ipic 20 0x8
386 0x8800 0x0 0x0 0x2 &ipic 21 0x8
387 0x8800 0x0 0x0 0x3 &ipic 22 0x8
388 0x8800 0x0 0x0 0x4 &ipic 23 0x8
390 /* IDSEL 0x12 AD18 */
391 0x9000 0x0 0x0 0x1 &ipic 22 0x8
392 0x9000 0x0 0x0 0x2 &ipic 23 0x8
393 0x9000 0x0 0x0 0x3 &ipic 20 0x8
394 0x9000 0x0 0x0 0x4 &ipic 21 0x8
396 /* IDSEL 0x13 AD19 */
397 0x9800 0x0 0x0 0x1 &ipic 23 0x8
398 0x9800 0x0 0x0 0x2 &ipic 20 0x8
399 0x9800 0x0 0x0 0x3 &ipic 21 0x8
400 0x9800 0x0 0x0 0x4 &ipic 22 0x8
402 /* IDSEL 0x15 AD21*/
403 0xa800 0x0 0x0 0x1 &ipic 20 0x8
404 0xa800 0x0 0x0 0x2 &ipic 21 0x8
405 0xa800 0x0 0x0 0x3 &ipic 22 0x8
406 0xa800 0x0 0x0 0x4 &ipic 23 0x8
408 /* IDSEL 0x16 AD22*/
409 0xb000 0x0 0x0 0x1 &ipic 23 0x8
410 0xb000 0x0 0x0 0x2 &ipic 20 0x8
411 0xb000 0x0 0x0 0x3 &ipic 21 0x8
412 0xb000 0x0 0x0 0x4 &ipic 22 0x8
414 /* IDSEL 0x17 AD23*/
415 0xb800 0x0 0x0 0x1 &ipic 22 0x8
416 0xb800 0x0 0x0 0x2 &ipic 23 0x8
417 0xb800 0x0 0x0 0x3 &ipic 20 0x8
418 0xb800 0x0 0x0 0x4 &ipic 21 0x8
420 /* IDSEL 0x18 AD24*/
421 0xc000 0x0 0x0 0x1 &ipic 21 0x8
422 0xc000 0x0 0x0 0x2 &ipic 22 0x8
423 0xc000 0x0 0x0 0x3 &ipic 23 0x8
424 0xc000 0x0 0x0 0x4 &ipic 20 0x8>;
425 interrupt-parent = <&ipic>;
426 interrupts = <66 0x8>;
427 bus-range = <0x0 0x0>;
428 ranges = <0x02000000 0x0 0x90000000 0x90000000 0x0 0x10000000
429 0x42000000 0x0 0x80000000 0x80000000 0x0 0x10000000
430 0x01000000 0x0 0x00000000 0xd0000000 0x0 0x00100000>;
431 clock-frequency = <0>;
432 #interrupt-cells = <1>;
433 #size-cells = <2>;
434 #address-cells = <3>;
435 reg = <0xe0008500 0x100 /* internal registers */
436 0xe0008300 0x8>; /* config space access registers */
437 compatible = "fsl,mpc8349-pci";
438 device_type = "pci";
439 sleep = <&pmc 0x00010000>;
440 };
441 };