sh_eth: fix EESIPR values for SH77{34|63}

[linux/fpc-iii.git] / drivers / edac / r82600_edac.c

/*
 * Radisys 82600 Embedded chipset Memory Controller kernel module
 * (C) 2005 EADS Astrium
 * This file may be distributed under the terms of the
 * GNU General Public License.
 *
 * Written by Tim Small <tim@buttersideup.com>, based on work by Thayne
 * Harbaugh, Dan Hollis <goemon at anime dot net> and others.
 *
 * $Id: edac_r82600.c,v 1.1.2.6 2005/10/05 00:43:44 dsp_llnl Exp $
 *
 * Written with reference to 82600 High Integration Dual PCI System
 * Controller Data Book:
 * www.radisys.com/files/support_downloads/007-01277-0002.82600DataBook.pdf
 * references to this document given in []
 */

#include <linux/module.h>
#include <linux/init.h>
#include <linux/pci.h>
#include <linux/pci_ids.h>
#include <linux/edac.h>
#include "edac_module.h"

#define R82600_REVISION " Ver: 2.0.2"
#define EDAC_MOD_STR    "r82600_edac"

#define r82600_printk(level, fmt, arg...) \
        edac_printk(level, "r82600", fmt, ##arg)

#define r82600_mc_printk(mci, level, fmt, arg...) \
        edac_mc_chipset_printk(mci, level, "r82600", fmt, ##arg)

/* Radisys say "The 82600 integrates a main memory SDRAM controller that
 * supports up to four banks of memory. The four banks can support a mix of
 * sizes of 64 bit wide (72 bits with ECC) Synchronous DRAM (SDRAM) DIMMs,
 * each of which can be any size from 16MB to 512MB. Both registered (control
 * signals buffered) and unbuffered DIMM types are supported. Mixing of
 * registered and unbuffered DIMMs as well as mixing of ECC and non-ECC DIMMs
 * is not allowed. The 82600 SDRAM interface operates at the same frequency as
 * the CPU bus, 66MHz, 100MHz or 133MHz."
 */

#define R82600_NR_CSROWS 4
#define R82600_NR_CHANS  1
#define R82600_NR_DIMMS  4

#define R82600_BRIDGE_ID  0x8200

/* Radisys 82600 register addresses - device 0 function 0 - PCI bridge */
#define R82600_DRAMC    0x57    /* Various SDRAM related control bits
                                 * all bits are R/W
                                 *
                                 * 7    SDRAM ISA Hole Enable
                                 * 6    Flash Page Mode Enable
                                 * 5    ECC Enable: 1=ECC 0=noECC
                                 * 4    DRAM DIMM Type: 1=
                                 * 3    BIOS Alias Disable
                                 * 2    SDRAM BIOS Flash Write Enable
                                 * 1:0  SDRAM Refresh Rate: 00=Disabled
                                 *          01=7.8usec (256Mbit SDRAMs)
                                 *          10=15.6us 11=125usec
                                 */

#define R82600_SDRAMC   0x76    /* "SDRAM Control Register"
                                 * More SDRAM related control bits
                                 * all bits are R/W
                                 *
                                 * 15:8 Reserved.
                                 *
                                 * 7:5  Special SDRAM Mode Select
                                 *
                                 * 4    Force ECC
                                 *
                                 *        1=Drive ECC bits to 0 during
                                 *          write cycles (i.e. ECC test mode)
                                 *
                                 *        0=Normal ECC functioning
                                 *
                                 * 3    Enhanced Paging Enable
                                 *
                                 * 2    CAS# Latency 0=3clks 1=2clks
                                 *
                                 * 1    RAS# to CAS# Delay 0=3 1=2
                                 *
                                 * 0    RAS# Precharge     0=3 1=2
                                 */

#define R82600_EAP      0x80    /* ECC Error Address Pointer Register
                                 *
                                 * 31    Disable Hardware Scrubbing (RW)
                                 *        0=Scrub on corrected read
                                 *        1=Don't scrub on corrected read
                                 *
                                 * 30:12 Error Address Pointer (RO)
                                 *        Upper 19 bits of error address
                                 *
                                 * 11:4  Syndrome Bits (RO)
                                 *
                                 * 3     BSERR# on multibit error (RW)
                                 *        1=enable 0=disable
                                 *
                                 * 2     NMI on Single Bit Eror (RW)
                                 *        1=NMI triggered by SBE n.b. other
                                 *          prerequeists
                                 *        0=NMI not triggered
                                 *
                                 * 1     MBE (R/WC)
                                 *        read 1=MBE at EAP (see above)
                                 *        read 0=no MBE, or SBE occurred first
                                 *        write 1=Clear MBE status (must also
                                 *          clear SBE)
                                 *        write 0=NOP
                                 *
                                 * 1     SBE (R/WC)
                                 *        read 1=SBE at EAP (see above)
                                 *        read 0=no SBE, or MBE occurred first
                                 *        write 1=Clear SBE status (must also
                                 *          clear MBE)
                                 *        write 0=NOP
                                 */

#define R82600_DRBA     0x60    /* + 0x60..0x63 SDRAM Row Boundary Address
                                 *  Registers
                                 *
                                 * 7:0  Address lines 30:24 - upper limit of
                                 * each row [p57]
                                 */

struct r82600_error_info {
        u32 eapr;
};

static bool disable_hardware_scrub;

static struct edac_pci_ctl_info *r82600_pci;

static void r82600_get_error_info(struct mem_ctl_info *mci,
                                struct r82600_error_info *info)
{
        struct pci_dev *pdev;

        pdev = to_pci_dev(mci->pdev);
        pci_read_config_dword(pdev, R82600_EAP, &info->eapr);

        if (info->eapr & BIT(0))
                /* Clear error to allow next error to be reported [p.62] */
                pci_write_bits32(pdev, R82600_EAP,
                                 ((u32) BIT(0) & (u32) BIT(1)),
                                 ((u32) BIT(0) & (u32) BIT(1)));

        if (info->eapr & BIT(1))
                /* Clear error to allow next error to be reported [p.62] */
                pci_write_bits32(pdev, R82600_EAP,
                                 ((u32) BIT(0) & (u32) BIT(1)),
                                 ((u32) BIT(0) & (u32) BIT(1)));
}

static int r82600_process_error_info(struct mem_ctl_info *mci,
                                struct r82600_error_info *info,
                                int handle_errors)
{
        int error_found;
        u32 eapaddr, page;
        u32 syndrome;

        error_found = 0;

        /* bits 30:12 store the upper 19 bits of the 32 bit error address */
        eapaddr = ((info->eapr >> 12) & 0x7FFF) << 13;
        /* Syndrome in bits 11:4 [p.62]       */
        syndrome = (info->eapr >> 4) & 0xFF;

        /* the R82600 reports at less than page *
         * granularity (upper 19 bits only)     */
        page = eapaddr >> PAGE_SHIFT;

        if (info->eapr & BIT(0)) {      /* CE? */
                error_found = 1;

                if (handle_errors)
                        edac_mc_handle_error(HW_EVENT_ERR_CORRECTED, mci, 1,
                                             page, 0, syndrome,
                                             edac_mc_find_csrow_by_page(mci, page),
                                             0, -1,
                                             mci->ctl_name, "");
        }

        if (info->eapr & BIT(1)) {      /* UE? */
                error_found = 1;

                if (handle_errors)
                        /* 82600 doesn't give enough info */
                        edac_mc_handle_error(HW_EVENT_ERR_UNCORRECTED, mci, 1,
                                             page, 0, 0,
                                             edac_mc_find_csrow_by_page(mci, page),
                                             0, -1,
                                             mci->ctl_name, "");
        }

        return error_found;
}

static void r82600_check(struct mem_ctl_info *mci)
{
        struct r82600_error_info info;

        edac_dbg(1, "MC%d\n", mci->mc_idx);
        r82600_get_error_info(mci, &info);
        r82600_process_error_info(mci, &info, 1);
}

static inline int ecc_enabled(u8 dramcr)
{
        return dramcr & BIT(5);
}

static void r82600_init_csrows(struct mem_ctl_info *mci, struct pci_dev *pdev,
                        u8 dramcr)
{
        struct csrow_info *csrow;
        struct dimm_info *dimm;
        int index;
        u8 drbar;               /* SDRAM Row Boundary Address Register */
        u32 row_high_limit, row_high_limit_last;
        u32 reg_sdram, ecc_on, row_base;

        ecc_on = ecc_enabled(dramcr);
        reg_sdram = dramcr & BIT(4);
        row_high_limit_last = 0;

        for (index = 0; index < mci->nr_csrows; index++) {
                csrow = mci->csrows[index];
                dimm = csrow->channels[0]->dimm;

                /* find the DRAM Chip Select Base address and mask */
                pci_read_config_byte(pdev, R82600_DRBA + index, &drbar);

                edac_dbg(1, "Row=%d DRBA = %#0x\n", index, drbar);

                row_high_limit = ((u32) drbar << 24);
/*              row_high_limit = ((u32)drbar << 24) | 0xffffffUL; */

                edac_dbg(1, "Row=%d, Boundary Address=%#0x, Last = %#0x\n",
                         index, row_high_limit, row_high_limit_last);

                /* Empty row [p.57] */
                if (row_high_limit == row_high_limit_last)
                        continue;

                row_base = row_high_limit_last;

                csrow->first_page = row_base >> PAGE_SHIFT;
                csrow->last_page = (row_high_limit >> PAGE_SHIFT) - 1;

                dimm->nr_pages = csrow->last_page - csrow->first_page + 1;
                /* Error address is top 19 bits - so granularity is      *
                 * 14 bits                                               */
                dimm->grain = 1 << 14;
                dimm->mtype = reg_sdram ? MEM_RDDR : MEM_DDR;
                /* FIXME - check that this is unknowable with this chipset */
                dimm->dtype = DEV_UNKNOWN;

                /* Mode is global on 82600 */
                dimm->edac_mode = ecc_on ? EDAC_SECDED : EDAC_NONE;
                row_high_limit_last = row_high_limit;
        }
}

static int r82600_probe1(struct pci_dev *pdev, int dev_idx)
{
        struct mem_ctl_info *mci;
        struct edac_mc_layer layers[2];
        u8 dramcr;
        u32 eapr;
        u32 scrub_disabled;
        u32 sdram_refresh_rate;
        struct r82600_error_info discard;

        edac_dbg(0, "\n");
        pci_read_config_byte(pdev, R82600_DRAMC, &dramcr);
        pci_read_config_dword(pdev, R82600_EAP, &eapr);
        scrub_disabled = eapr & BIT(31);
        sdram_refresh_rate = dramcr & (BIT(0) | BIT(1));
        edac_dbg(2, "sdram refresh rate = %#0x\n", sdram_refresh_rate);
        edac_dbg(2, "DRAMC register = %#0x\n", dramcr);
        layers[0].type = EDAC_MC_LAYER_CHIP_SELECT;
        layers[0].size = R82600_NR_CSROWS;
        layers[0].is_virt_csrow = true;
        layers[1].type = EDAC_MC_LAYER_CHANNEL;
        layers[1].size = R82600_NR_CHANS;
        layers[1].is_virt_csrow = false;
        mci = edac_mc_alloc(0, ARRAY_SIZE(layers), layers, 0);
        if (mci == NULL)
                return -ENOMEM;

        edac_dbg(0, "mci = %p\n", mci);
        mci->pdev = &pdev->dev;
        mci->mtype_cap = MEM_FLAG_RDDR | MEM_FLAG_DDR;
        mci->edac_ctl_cap = EDAC_FLAG_NONE | EDAC_FLAG_EC | EDAC_FLAG_SECDED;
        /* FIXME try to work out if the chip leads have been used for COM2
         * instead on this board? [MA6?] MAYBE:
         */

        /* On the R82600, the pins for memory bits 72:65 - i.e. the   *
         * EC bits are shared with the pins for COM2 (!), so if COM2  *
         * is enabled, we assume COM2 is wired up, and thus no EDAC   *
         * is possible.                                               */
        mci->edac_cap = EDAC_FLAG_NONE | EDAC_FLAG_EC | EDAC_FLAG_SECDED;

        if (ecc_enabled(dramcr)) {
                if (scrub_disabled)
                        edac_dbg(3, "mci = %p - Scrubbing disabled! EAP: %#0x\n",
                                 mci, eapr);
        } else
                mci->edac_cap = EDAC_FLAG_NONE;

        mci->mod_name = EDAC_MOD_STR;
        mci->mod_ver = R82600_REVISION;
        mci->ctl_name = "R82600";
        mci->dev_name = pci_name(pdev);
        mci->edac_check = r82600_check;
        mci->ctl_page_to_phys = NULL;
        r82600_init_csrows(mci, pdev, dramcr);
        r82600_get_error_info(mci, &discard);   /* clear counters */

        /* Here we assume that we will never see multiple instances of this
         * type of memory controller.  The ID is therefore hardcoded to 0.
         */
        if (edac_mc_add_mc(mci)) {
                edac_dbg(3, "failed edac_mc_add_mc()\n");
                goto fail;
        }

        /* get this far and it's successful */

        if (disable_hardware_scrub) {
                edac_dbg(3, "Disabling Hardware Scrub (scrub on error)\n");
                pci_write_bits32(pdev, R82600_EAP, BIT(31), BIT(31));
        }

        /* allocating generic PCI control info */
        r82600_pci = edac_pci_create_generic_ctl(&pdev->dev, EDAC_MOD_STR);
        if (!r82600_pci) {
                printk(KERN_WARNING
                        "%s(): Unable to create PCI control\n",
                        __func__);
                printk(KERN_WARNING
                        "%s(): PCI error report via EDAC not setup\n",
                        __func__);
        }

        edac_dbg(3, "success\n");
        return 0;

fail:
        edac_mc_free(mci);
        return -ENODEV;
}

/* returns count (>= 0), or negative on error */
static int r82600_init_one(struct pci_dev *pdev,
                           const struct pci_device_id *ent)
{
        edac_dbg(0, "\n");

        /* don't need to call pci_enable_device() */
        return r82600_probe1(pdev, ent->driver_data);
}

static void r82600_remove_one(struct pci_dev *pdev)
{
        struct mem_ctl_info *mci;

        edac_dbg(0, "\n");

        if (r82600_pci)
                edac_pci_release_generic_ctl(r82600_pci);

        if ((mci = edac_mc_del_mc(&pdev->dev)) == NULL)
                return;

        edac_mc_free(mci);
}

static const struct pci_device_id r82600_pci_tbl[] = {
        {
         PCI_DEVICE(PCI_VENDOR_ID_RADISYS, R82600_BRIDGE_ID)
         },
        {
         0,
         }                      /* 0 terminated list. */
};

MODULE_DEVICE_TABLE(pci, r82600_pci_tbl);

static struct pci_driver r82600_driver = {
        .name = EDAC_MOD_STR,
        .probe = r82600_init_one,
        .remove = r82600_remove_one,
        .id_table = r82600_pci_tbl,
};

static int __init r82600_init(void)
{
       /* Ensure that the OPSTATE is set correctly for POLL or NMI */
       opstate_init();

        return pci_register_driver(&r82600_driver);
}

static void __exit r82600_exit(void)
{
        pci_unregister_driver(&r82600_driver);
}

module_init(r82600_init);
module_exit(r82600_exit);

MODULE_LICENSE("GPL");
MODULE_AUTHOR("Tim Small <tim@buttersideup.com> - WPAD Ltd. "
                "on behalf of EADS Astrium");
MODULE_DESCRIPTION("MC support for Radisys 82600 memory controllers");

module_param(disable_hardware_scrub, bool, 0644);
MODULE_PARM_DESC(disable_hardware_scrub,
                 "If set, disable the chipset's automatic scrub for CEs");

module_param(edac_op_state, int, 0444);
MODULE_PARM_DESC(edac_op_state, "EDAC Error Reporting state: 0=Poll,1=NMI");