sh_eth: fix EESIPR values for SH77{34|63}
[linux/fpc-iii.git] / drivers / hwmon / tmp108.c
blob91bb946392869e5002097fdfa2f371dacc466f25
1 /* Texas Instruments TMP108 SMBus temperature sensor driver
3 * Copyright (C) 2016 John Muir <john@jmuir.com>
5 * This program is free software; you can redistribute it and/or modify
6 * it under the terms of the GNU General Public License as published by
7 * the Free Software Foundation; either version 2 of the License, or
8 * (at your option) any later version.
10 * This program is distributed in the hope that it will be useful,
11 * but WITHOUT ANY WARRANTY; without even the implied warranty of
12 * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
13 * GNU General Public License for more details.
16 #include <linux/delay.h>
17 #include <linux/device.h>
18 #include <linux/err.h>
19 #include <linux/hwmon.h>
20 #include <linux/hwmon-sysfs.h>
21 #include <linux/module.h>
22 #include <linux/mutex.h>
23 #include <linux/of.h>
24 #include <linux/i2c.h>
25 #include <linux/init.h>
26 #include <linux/jiffies.h>
27 #include <linux/regmap.h>
28 #include <linux/slab.h>
30 #define DRIVER_NAME "tmp108"
32 #define TMP108_REG_TEMP 0x00
33 #define TMP108_REG_CONF 0x01
34 #define TMP108_REG_TLOW 0x02
35 #define TMP108_REG_THIGH 0x03
37 #define TMP108_TEMP_MIN_MC -50000 /* Minimum millicelcius. */
38 #define TMP108_TEMP_MAX_MC 127937 /* Maximum millicelcius. */
40 /* Configuration register bits.
41 * Note: these bit definitions are byte swapped.
43 #define TMP108_CONF_M0 0x0100 /* Sensor mode. */
44 #define TMP108_CONF_M1 0x0200
45 #define TMP108_CONF_TM 0x0400 /* Thermostat mode. */
46 #define TMP108_CONF_FL 0x0800 /* Watchdog flag - TLOW */
47 #define TMP108_CONF_FH 0x1000 /* Watchdog flag - THIGH */
48 #define TMP108_CONF_CR0 0x2000 /* Conversion rate. */
49 #define TMP108_CONF_CR1 0x4000
50 #define TMP108_CONF_ID 0x8000
51 #define TMP108_CONF_HYS0 0x0010 /* Hysteresis. */
52 #define TMP108_CONF_HYS1 0x0020
53 #define TMP108_CONF_POL 0x0080 /* Polarity of alert. */
55 /* Defaults set by the hardware upon reset. */
56 #define TMP108_CONF_DEFAULTS (TMP108_CONF_CR0 | TMP108_CONF_TM |\
57 TMP108_CONF_HYS0 | TMP108_CONF_M1)
58 /* These bits are read-only. */
59 #define TMP108_CONF_READ_ONLY (TMP108_CONF_FL | TMP108_CONF_FH |\
60 TMP108_CONF_ID)
62 #define TMP108_CONF_MODE_MASK (TMP108_CONF_M0|TMP108_CONF_M1)
63 #define TMP108_MODE_SHUTDOWN 0x0000
64 #define TMP108_MODE_ONE_SHOT TMP108_CONF_M0
65 #define TMP108_MODE_CONTINUOUS TMP108_CONF_M1 /* Default */
66 /* When M1 is set, M0 is ignored. */
68 #define TMP108_CONF_CONVRATE_MASK (TMP108_CONF_CR0|TMP108_CONF_CR1)
69 #define TMP108_CONVRATE_0P25HZ 0x0000
70 #define TMP108_CONVRATE_1HZ TMP108_CONF_CR0 /* Default */
71 #define TMP108_CONVRATE_4HZ TMP108_CONF_CR1
72 #define TMP108_CONVRATE_16HZ (TMP108_CONF_CR0|TMP108_CONF_CR1)
74 #define TMP108_CONF_HYSTERESIS_MASK (TMP108_CONF_HYS0|TMP108_CONF_HYS1)
75 #define TMP108_HYSTERESIS_0C 0x0000
76 #define TMP108_HYSTERESIS_1C TMP108_CONF_HYS0 /* Default */
77 #define TMP108_HYSTERESIS_2C TMP108_CONF_HYS1
78 #define TMP108_HYSTERESIS_4C (TMP108_CONF_HYS0|TMP108_CONF_HYS1)
80 #define TMP108_CONVERSION_TIME_MS 30 /* in milli-seconds */
82 struct tmp108 {
83 struct regmap *regmap;
84 u16 orig_config;
85 unsigned long ready_time;
88 /* convert 12-bit TMP108 register value to milliCelsius */
89 static inline int tmp108_temp_reg_to_mC(s16 val)
91 return (val & ~0x0f) * 1000 / 256;
94 /* convert milliCelsius to left adjusted 12-bit TMP108 register value */
95 static inline u16 tmp108_mC_to_temp_reg(int val)
97 return (val * 256) / 1000;
100 static int tmp108_read(struct device *dev, enum hwmon_sensor_types type,
101 u32 attr, int channel, long *temp)
103 struct tmp108 *tmp108 = dev_get_drvdata(dev);
104 unsigned int regval;
105 int err, hyst;
107 if (type == hwmon_chip) {
108 if (attr == hwmon_chip_update_interval) {
109 err = regmap_read(tmp108->regmap, TMP108_REG_CONF,
110 &regval);
111 if (err < 0)
112 return err;
113 switch (regval & TMP108_CONF_CONVRATE_MASK) {
114 case TMP108_CONVRATE_0P25HZ:
115 default:
116 *temp = 4000;
117 break;
118 case TMP108_CONVRATE_1HZ:
119 *temp = 1000;
120 break;
121 case TMP108_CONVRATE_4HZ:
122 *temp = 250;
123 break;
124 case TMP108_CONVRATE_16HZ:
125 *temp = 63;
126 break;
128 return 0;
130 return -EOPNOTSUPP;
133 switch (attr) {
134 case hwmon_temp_input:
135 /* Is it too early to return a conversion ? */
136 if (time_before(jiffies, tmp108->ready_time)) {
137 dev_dbg(dev, "%s: Conversion not ready yet..\n",
138 __func__);
139 return -EAGAIN;
141 err = regmap_read(tmp108->regmap, TMP108_REG_TEMP, &regval);
142 if (err < 0)
143 return err;
144 *temp = tmp108_temp_reg_to_mC(regval);
145 break;
146 case hwmon_temp_min:
147 case hwmon_temp_max:
148 err = regmap_read(tmp108->regmap, attr == hwmon_temp_min ?
149 TMP108_REG_TLOW : TMP108_REG_THIGH, &regval);
150 if (err < 0)
151 return err;
152 *temp = tmp108_temp_reg_to_mC(regval);
153 break;
154 case hwmon_temp_min_alarm:
155 case hwmon_temp_max_alarm:
156 err = regmap_read(tmp108->regmap, TMP108_REG_CONF, &regval);
157 if (err < 0)
158 return err;
159 *temp = !!(regval & (attr == hwmon_temp_min_alarm ?
160 TMP108_CONF_FL : TMP108_CONF_FH));
161 break;
162 case hwmon_temp_min_hyst:
163 case hwmon_temp_max_hyst:
164 err = regmap_read(tmp108->regmap, TMP108_REG_CONF, &regval);
165 if (err < 0)
166 return err;
167 switch (regval & TMP108_CONF_HYSTERESIS_MASK) {
168 case TMP108_HYSTERESIS_0C:
169 default:
170 hyst = 0;
171 break;
172 case TMP108_HYSTERESIS_1C:
173 hyst = 1000;
174 break;
175 case TMP108_HYSTERESIS_2C:
176 hyst = 2000;
177 break;
178 case TMP108_HYSTERESIS_4C:
179 hyst = 4000;
180 break;
182 err = regmap_read(tmp108->regmap, attr == hwmon_temp_min_hyst ?
183 TMP108_REG_TLOW : TMP108_REG_THIGH, &regval);
184 if (err < 0)
185 return err;
186 *temp = tmp108_temp_reg_to_mC(regval);
187 if (attr == hwmon_temp_min_hyst)
188 *temp += hyst;
189 else
190 *temp -= hyst;
191 break;
192 default:
193 return -EOPNOTSUPP;
196 return 0;
199 static int tmp108_write(struct device *dev, enum hwmon_sensor_types type,
200 u32 attr, int channel, long temp)
202 struct tmp108 *tmp108 = dev_get_drvdata(dev);
203 u32 regval, mask;
204 int err;
206 if (type == hwmon_chip) {
207 if (attr == hwmon_chip_update_interval) {
208 if (temp < 156)
209 mask = TMP108_CONVRATE_16HZ;
210 else if (temp < 625)
211 mask = TMP108_CONVRATE_4HZ;
212 else if (temp < 2500)
213 mask = TMP108_CONVRATE_1HZ;
214 else
215 mask = TMP108_CONVRATE_0P25HZ;
216 return regmap_update_bits(tmp108->regmap,
217 TMP108_REG_CONF,
218 TMP108_CONF_CONVRATE_MASK,
219 mask);
221 return -EOPNOTSUPP;
224 switch (attr) {
225 case hwmon_temp_min:
226 case hwmon_temp_max:
227 temp = clamp_val(temp, TMP108_TEMP_MIN_MC, TMP108_TEMP_MAX_MC);
228 return regmap_write(tmp108->regmap,
229 attr == hwmon_temp_min ?
230 TMP108_REG_TLOW : TMP108_REG_THIGH,
231 tmp108_mC_to_temp_reg(temp));
232 case hwmon_temp_min_hyst:
233 case hwmon_temp_max_hyst:
234 temp = clamp_val(temp, TMP108_TEMP_MIN_MC, TMP108_TEMP_MAX_MC);
235 err = regmap_read(tmp108->regmap,
236 attr == hwmon_temp_min_hyst ?
237 TMP108_REG_TLOW : TMP108_REG_THIGH,
238 &regval);
239 if (err < 0)
240 return err;
241 if (attr == hwmon_temp_min_hyst)
242 temp -= tmp108_temp_reg_to_mC(regval);
243 else
244 temp = tmp108_temp_reg_to_mC(regval) - temp;
245 if (temp < 500)
246 mask = TMP108_HYSTERESIS_0C;
247 else if (temp < 1500)
248 mask = TMP108_HYSTERESIS_1C;
249 else if (temp < 3000)
250 mask = TMP108_HYSTERESIS_2C;
251 else
252 mask = TMP108_HYSTERESIS_4C;
253 return regmap_update_bits(tmp108->regmap, TMP108_REG_CONF,
254 TMP108_CONF_HYSTERESIS_MASK, mask);
255 default:
256 return -EOPNOTSUPP;
260 static umode_t tmp108_is_visible(const void *data, enum hwmon_sensor_types type,
261 u32 attr, int channel)
263 if (type == hwmon_chip && attr == hwmon_chip_update_interval)
264 return 0644;
266 if (type != hwmon_temp)
267 return 0;
269 switch (attr) {
270 case hwmon_temp_input:
271 case hwmon_temp_min_alarm:
272 case hwmon_temp_max_alarm:
273 return 0444;
274 case hwmon_temp_min:
275 case hwmon_temp_max:
276 case hwmon_temp_min_hyst:
277 case hwmon_temp_max_hyst:
278 return 0644;
279 default:
280 return 0;
284 static u32 tmp108_chip_config[] = {
285 HWMON_C_REGISTER_TZ | HWMON_C_UPDATE_INTERVAL,
289 static const struct hwmon_channel_info tmp108_chip = {
290 .type = hwmon_chip,
291 .config = tmp108_chip_config,
294 static u32 tmp108_temp_config[] = {
295 HWMON_T_INPUT | HWMON_T_MAX | HWMON_T_MIN | HWMON_T_MIN_HYST
296 | HWMON_T_MAX_HYST | HWMON_T_MIN_ALARM | HWMON_T_MAX_ALARM,
300 static const struct hwmon_channel_info tmp108_temp = {
301 .type = hwmon_temp,
302 .config = tmp108_temp_config,
305 static const struct hwmon_channel_info *tmp108_info[] = {
306 &tmp108_chip,
307 &tmp108_temp,
308 NULL
311 static const struct hwmon_ops tmp108_hwmon_ops = {
312 .is_visible = tmp108_is_visible,
313 .read = tmp108_read,
314 .write = tmp108_write,
317 static const struct hwmon_chip_info tmp108_chip_info = {
318 .ops = &tmp108_hwmon_ops,
319 .info = tmp108_info,
322 static void tmp108_restore_config(void *data)
324 struct tmp108 *tmp108 = data;
326 regmap_write(tmp108->regmap, TMP108_REG_CONF, tmp108->orig_config);
329 static bool tmp108_is_writeable_reg(struct device *dev, unsigned int reg)
331 return reg != TMP108_REG_TEMP;
334 static bool tmp108_is_volatile_reg(struct device *dev, unsigned int reg)
336 /* Configuration register must be volatile to enable FL and FH. */
337 return reg == TMP108_REG_TEMP || reg == TMP108_REG_CONF;
340 static const struct regmap_config tmp108_regmap_config = {
341 .reg_bits = 8,
342 .val_bits = 16,
343 .max_register = TMP108_REG_THIGH,
344 .writeable_reg = tmp108_is_writeable_reg,
345 .volatile_reg = tmp108_is_volatile_reg,
346 .val_format_endian = REGMAP_ENDIAN_BIG,
347 .cache_type = REGCACHE_RBTREE,
348 .use_single_rw = true,
351 static int tmp108_probe(struct i2c_client *client,
352 const struct i2c_device_id *id)
354 struct device *dev = &client->dev;
355 struct device *hwmon_dev;
356 struct tmp108 *tmp108;
357 int err;
358 u32 config;
360 if (!i2c_check_functionality(client->adapter,
361 I2C_FUNC_SMBUS_WORD_DATA)) {
362 dev_err(dev,
363 "adapter doesn't support SMBus word transactions\n");
364 return -ENODEV;
367 tmp108 = devm_kzalloc(dev, sizeof(*tmp108), GFP_KERNEL);
368 if (!tmp108)
369 return -ENOMEM;
371 dev_set_drvdata(dev, tmp108);
373 tmp108->regmap = devm_regmap_init_i2c(client, &tmp108_regmap_config);
374 if (IS_ERR(tmp108->regmap)) {
375 err = PTR_ERR(tmp108->regmap);
376 dev_err(dev, "regmap init failed: %d", err);
377 return err;
380 err = regmap_read(tmp108->regmap, TMP108_REG_CONF, &config);
381 if (err < 0) {
382 dev_err(dev, "error reading config register: %d", err);
383 return err;
385 tmp108->orig_config = config;
387 /* Only continuous mode is supported. */
388 config &= ~TMP108_CONF_MODE_MASK;
389 config |= TMP108_MODE_CONTINUOUS;
391 /* Only comparator mode is supported. */
392 config &= ~TMP108_CONF_TM;
394 err = regmap_write(tmp108->regmap, TMP108_REG_CONF, config);
395 if (err < 0) {
396 dev_err(dev, "error writing config register: %d", err);
397 return err;
400 tmp108->ready_time = jiffies;
401 if ((tmp108->orig_config & TMP108_CONF_MODE_MASK) ==
402 TMP108_MODE_SHUTDOWN)
403 tmp108->ready_time +=
404 msecs_to_jiffies(TMP108_CONVERSION_TIME_MS);
406 err = devm_add_action_or_reset(dev, tmp108_restore_config, tmp108);
407 if (err) {
408 dev_err(dev, "add action or reset failed: %d", err);
409 return err;
412 hwmon_dev = devm_hwmon_device_register_with_info(dev, client->name,
413 tmp108,
414 &tmp108_chip_info,
415 NULL);
416 return PTR_ERR_OR_ZERO(hwmon_dev);
419 static int __maybe_unused tmp108_suspend(struct device *dev)
421 struct tmp108 *tmp108 = dev_get_drvdata(dev);
423 return regmap_update_bits(tmp108->regmap, TMP108_REG_CONF,
424 TMP108_CONF_MODE_MASK, TMP108_MODE_SHUTDOWN);
427 static int __maybe_unused tmp108_resume(struct device *dev)
429 struct tmp108 *tmp108 = dev_get_drvdata(dev);
430 int err;
432 err = regmap_update_bits(tmp108->regmap, TMP108_REG_CONF,
433 TMP108_CONF_MODE_MASK, TMP108_MODE_CONTINUOUS);
434 tmp108->ready_time = jiffies +
435 msecs_to_jiffies(TMP108_CONVERSION_TIME_MS);
436 return err;
439 static SIMPLE_DEV_PM_OPS(tmp108_dev_pm_ops, tmp108_suspend, tmp108_resume);
441 static const struct i2c_device_id tmp108_i2c_ids[] = {
442 { "tmp108", 0 },
445 MODULE_DEVICE_TABLE(i2c, tmp108_i2c_ids);
447 #ifdef CONFIG_OF
448 static const struct of_device_id tmp108_of_ids[] = {
449 { .compatible = "ti,tmp108", },
452 MODULE_DEVICE_TABLE(of, tmp108_of_ids);
453 #endif
455 static struct i2c_driver tmp108_driver = {
456 .driver = {
457 .name = DRIVER_NAME,
458 .pm = &tmp108_dev_pm_ops,
459 .of_match_table = of_match_ptr(tmp108_of_ids),
461 .probe = tmp108_probe,
462 .id_table = tmp108_i2c_ids,
465 module_i2c_driver(tmp108_driver);
467 MODULE_AUTHOR("John Muir <john@jmuir.com>");
468 MODULE_DESCRIPTION("Texas Instruments TMP108 temperature sensor driver");
469 MODULE_LICENSE("GPL");