drivers/iio/common/st_sensors/st_sensors_trigger.c

   1 /*
   2  * STMicroelectronics sensors trigger library driver
   3  *
   4  * Copyright 2012-2013 STMicroelectronics Inc.
   5  *
   6  * Denis Ciocca <denis.ciocca@st.com>
   7  *
   8  * Licensed under the GPL-2.
   9  */
  10
  11 #include <linux/kernel.h>
  12 #include <linux/module.h>
  13 #include <linux/slab.h>
  14 #include <linux/iio/iio.h>
  15 #include <linux/iio/trigger.h>
  16 #include <linux/interrupt.h>
  17 #include <linux/iio/common/st_sensors.h>
  18 #include "st_sensors_core.h"
  19
  20 /**
  21  * st_sensors_new_samples_available() - check if more samples came in
  22  * returns:
  23  * 0 - no new samples available
  24  * 1 - new samples available
  25  * negative - error or unknown
  26  */
  27 static int st_sensors_new_samples_available(struct iio_dev *indio_dev,
  28                                             struct st_sensor_data *sdata)
  29 {
  30         u8 status;
  31         int ret;
  32
  33         /* How would I know if I can't check it? */
  34         if (!sdata->sensor_settings->drdy_irq.addr_stat_drdy)
  35                 return -EINVAL;
  36
  37         /* No scan mask, no interrupt */
  38         if (!indio_dev->active_scan_mask)
  39                 return 0;
  40
  41         ret = sdata->tf->read_byte(&sdata->tb, sdata->dev,
  42                         sdata->sensor_settings->drdy_irq.addr_stat_drdy,
  43                         &status);
  44         if (ret < 0) {
  45                 dev_err(sdata->dev,
  46                         "error checking samples available\n");
  47                 return ret;
  48         }
  49         /*
  50          * the lower bits of .active_scan_mask[0] is directly mapped
  51          * to the channels on the sensor: either bit 0 for
  52          * one-dimensional sensors, or e.g. x,y,z for accelerometers,
  53          * gyroscopes or magnetometers. No sensor use more than 3
  54          * channels, so cut the other status bits here.
  55          */
  56         status &= 0x07;
  57
  58         if (status & (u8)indio_dev->active_scan_mask[0])
  59                 return 1;
  60
  61         return 0;
  62 }
  63
  64 /**
  65  * st_sensors_irq_handler() - top half of the IRQ-based triggers
  66  * @irq: irq number
  67  * @p: private handler data
  68  */
  69 static irqreturn_t st_sensors_irq_handler(int irq, void *p)
  70 {
  71         struct iio_trigger *trig = p;
  72         struct iio_dev *indio_dev = iio_trigger_get_drvdata(trig);
  73         struct st_sensor_data *sdata = iio_priv(indio_dev);
  74
  75         /* Get the time stamp as close in time as possible */
  76         sdata->hw_timestamp = iio_get_time_ns(indio_dev);
  77         return IRQ_WAKE_THREAD;
  78 }
  79
  80 /**
  81  * st_sensors_irq_thread() - bottom half of the IRQ-based triggers
  82  * @irq: irq number
  83  * @p: private handler data
  84  */
  85 static irqreturn_t st_sensors_irq_thread(int irq, void *p)
  86 {
  87         struct iio_trigger *trig = p;
  88         struct iio_dev *indio_dev = iio_trigger_get_drvdata(trig);
  89         struct st_sensor_data *sdata = iio_priv(indio_dev);
  90
  91         /*
  92          * If this trigger is backed by a hardware interrupt and we have a
  93          * status register, check if this IRQ came from us. Notice that
  94          * we will process also if st_sensors_new_samples_available()
  95          * returns negative: if we can't check status, then poll
  96          * unconditionally.
  97          */
  98         if (sdata->hw_irq_trigger &&
  99             st_sensors_new_samples_available(indio_dev, sdata)) {
 100                 iio_trigger_poll_chained(p);
 101         } else {
 102                 dev_dbg(sdata->dev, "spurious IRQ\n");
 103                 return IRQ_NONE;
 104         }
 105
 106         /*
 107          * If we have proper level IRQs the handler will be re-entered if
 108          * the line is still active, so return here and come back in through
 109          * the top half if need be.
 110          */
 111         if (!sdata->edge_irq)
 112                 return IRQ_HANDLED;
 113
 114         /*
 115          * If we are using egde IRQs, new samples arrived while processing
 116          * the IRQ and those may be missed unless we pick them here, so poll
 117          * again. If the sensor delivery frequency is very high, this thread
 118          * turns into a polled loop handler.
 119          */
 120         while (sdata->hw_irq_trigger &&
 121                st_sensors_new_samples_available(indio_dev, sdata)) {
 122                 dev_dbg(sdata->dev, "more samples came in during polling\n");
 123                 sdata->hw_timestamp = iio_get_time_ns(indio_dev);
 124                 iio_trigger_poll_chained(p);
 125         }
 126
 127         return IRQ_HANDLED;
 128 }
 129
 130 int st_sensors_allocate_trigger(struct iio_dev *indio_dev,
 131                                 const struct iio_trigger_ops *trigger_ops)
 132 {
 133         int err, irq;
 134         struct st_sensor_data *sdata = iio_priv(indio_dev);
 135         unsigned long irq_trig;
 136
 137         sdata->trig = iio_trigger_alloc("%s-trigger", indio_dev->name);
 138         if (sdata->trig == NULL) {
 139                 dev_err(&indio_dev->dev, "failed to allocate iio trigger.\n");
 140                 return -ENOMEM;
 141         }
 142
 143         iio_trigger_set_drvdata(sdata->trig, indio_dev);
 144         sdata->trig->ops = trigger_ops;
 145         sdata->trig->dev.parent = sdata->dev;
 146
 147         irq = sdata->get_irq_data_ready(indio_dev);
 148         irq_trig = irqd_get_trigger_type(irq_get_irq_data(irq));
 149         /*
 150          * If the IRQ is triggered on falling edge, we need to mark the
 151          * interrupt as active low, if the hardware supports this.
 152          */
 153         switch(irq_trig) {
 154         case IRQF_TRIGGER_FALLING:
 155         case IRQF_TRIGGER_LOW:
 156                 if (!sdata->sensor_settings->drdy_irq.addr_ihl) {
 157                         dev_err(&indio_dev->dev,
 158                                 "falling/low specified for IRQ "
 159                                 "but hardware only support rising/high: "
 160                                 "will request rising/high\n");
 161                         if (irq_trig == IRQF_TRIGGER_FALLING)
 162                                 irq_trig = IRQF_TRIGGER_RISING;
 163                         if (irq_trig == IRQF_TRIGGER_LOW)
 164                                 irq_trig = IRQF_TRIGGER_HIGH;
 165                 } else {
 166                         /* Set up INT active low i.e. falling edge */
 167                         err = st_sensors_write_data_with_mask(indio_dev,
 168                                 sdata->sensor_settings->drdy_irq.addr_ihl,
 169                                 sdata->sensor_settings->drdy_irq.mask_ihl, 1);
 170                         if (err < 0)
 171                                 goto iio_trigger_free;
 172                         dev_info(&indio_dev->dev,
 173                                  "interrupts on the falling edge or "
 174                                  "active low level\n");
 175                 }
 176                 break;
 177         case IRQF_TRIGGER_RISING:
 178                 dev_info(&indio_dev->dev,
 179                          "interrupts on the rising edge\n");
 180                 break;
 181         case IRQF_TRIGGER_HIGH:
 182                 dev_info(&indio_dev->dev,
 183                          "interrupts active high level\n");
 184                 break;
 185         default:
 186                 /* This is the most preferred mode, if possible */
 187                 dev_err(&indio_dev->dev,
 188                         "unsupported IRQ trigger specified (%lx), enforce "
 189                         "rising edge\n", irq_trig);
 190                 irq_trig = IRQF_TRIGGER_RISING;
 191         }
 192
 193         /* Tell the interrupt handler that we're dealing with edges */
 194         if (irq_trig == IRQF_TRIGGER_FALLING ||
 195             irq_trig == IRQF_TRIGGER_RISING)
 196                 sdata->edge_irq = true;
 197         else
 198                 /*
 199                  * If we're not using edges (i.e. level interrupts) we
 200                  * just mask off the IRQ, handle one interrupt, then
 201                  * if the line is still low, we return to the
 202                  * interrupt handler top half again and start over.
 203                  */
 204                 irq_trig |= IRQF_ONESHOT;
 205
 206         /*
 207          * If the interrupt pin is Open Drain, by definition this
 208          * means that the interrupt line may be shared with other
 209          * peripherals. But to do this we also need to have a status
 210          * register and mask to figure out if this sensor was firing
 211          * the IRQ or not, so we can tell the interrupt handle that
 212          * it was "our" interrupt.
 213          */
 214         if (sdata->int_pin_open_drain &&
 215             sdata->sensor_settings->drdy_irq.addr_stat_drdy)
 216                 irq_trig |= IRQF_SHARED;
 217
 218         err = request_threaded_irq(sdata->get_irq_data_ready(indio_dev),
 219                         st_sensors_irq_handler,
 220                         st_sensors_irq_thread,
 221                         irq_trig,
 222                         sdata->trig->name,
 223                         sdata->trig);
 224         if (err) {
 225                 dev_err(&indio_dev->dev, "failed to request trigger IRQ.\n");
 226                 goto iio_trigger_free;
 227         }
 228
 229         err = iio_trigger_register(sdata->trig);
 230         if (err < 0) {
 231                 dev_err(&indio_dev->dev, "failed to register iio trigger.\n");
 232                 goto iio_trigger_register_error;
 233         }
 234         indio_dev->trig = iio_trigger_get(sdata->trig);
 235
 236         return 0;
 237
 238 iio_trigger_register_error:
 239         free_irq(sdata->get_irq_data_ready(indio_dev), sdata->trig);
 240 iio_trigger_free:
 241         iio_trigger_free(sdata->trig);
 242         return err;
 243 }
 244 EXPORT_SYMBOL(st_sensors_allocate_trigger);
 245
 246 void st_sensors_deallocate_trigger(struct iio_dev *indio_dev)
 247 {
 248         struct st_sensor_data *sdata = iio_priv(indio_dev);
 249
 250         iio_trigger_unregister(sdata->trig);
 251         free_irq(sdata->get_irq_data_ready(indio_dev), sdata->trig);
 252         iio_trigger_free(sdata->trig);
 253 }
 254 EXPORT_SYMBOL(st_sensors_deallocate_trigger);
 255
 256 int st_sensors_validate_device(struct iio_trigger *trig,
 257                                struct iio_dev *indio_dev)
 258 {
 259         struct iio_dev *indio = iio_trigger_get_drvdata(trig);
 260
 261         if (indio != indio_dev)
 262                 return -EINVAL;
 263
 264         return 0;
 265 }
 266 EXPORT_SYMBOL(st_sensors_validate_device);
 267
 268 MODULE_AUTHOR("Denis Ciocca <denis.ciocca@st.com>");
 269 MODULE_DESCRIPTION("STMicroelectronics ST-sensors trigger");
 270 MODULE_LICENSE("GPL v2");