drivers/ipack/devices/scc2698.h

   1 /*
   2  * scc2698.h
   3  *
   4  * driver for the IPOCTAL boards
   5  *
   6  * Copyright (C) 2009-2012 CERN (www.cern.ch)
   7  * Author: Nicolas Serafini, EIC2 SA
   8  * Author: Samuel Iglesias Gonsalvez <siglesias@igalia.com>
   9  *
  10  * This program is free software; you can redistribute it and/or modify it
  11  * under the terms of the GNU General Public License as published by the Free
  12  * Software Foundation; version 2 of the License.
  13  */
  14
  15 #ifndef SCC2698_H_
  16 #define SCC2698_H_
  17
  18 /*
  19  * union scc2698_channel - Channel access to scc2698 IO
  20  *
  21  * dn value are only spacer.
  22  *
  23  */
  24 union scc2698_channel {
  25         struct {
  26                 u8 d0, mr;  /* Mode register 1/2*/
  27                 u8 d1, sr;  /* Status register */
  28                 u8 d2, r1;  /* reserved */
  29                 u8 d3, rhr; /* Receive holding register (R) */
  30                 u8 junk[8]; /* other crap for block control */
  31         } __packed r; /* Read access */
  32         struct {
  33                 u8 d0, mr;  /* Mode register 1/2 */
  34                 u8 d1, csr; /* Clock select register */
  35                 u8 d2, cr;  /* Command register */
  36                 u8 d3, thr; /* Transmit holding register */
  37                 u8 junk[8]; /* other crap for block control */
  38         } __packed w; /* Write access */
  39 };
  40
  41 /*
  42  * union scc2698_block - Block access to scc2698 IO
  43  *
  44  * The scc2698 contain 4 block.
  45  * Each block containt two channel a and b.
  46  * dn value are only spacer.
  47  *
  48  */
  49 union scc2698_block {
  50         struct {
  51                 u8 d0, mra;  /* Mode register 1/2 (a) */
  52                 u8 d1, sra;  /* Status register (a) */
  53                 u8 d2, r1;   /* reserved */
  54                 u8 d3, rhra; /* Receive holding register (a) */
  55                 u8 d4, ipcr; /* Input port change register of block */
  56                 u8 d5, isr;  /* Interrupt status register of block */
  57                 u8 d6, ctur; /* Counter timer upper register of block */
  58                 u8 d7, ctlr; /* Counter timer lower register of block */
  59                 u8 d8, mrb;  /* Mode register 1/2 (b) */
  60                 u8 d9, srb;  /* Status register (b) */
  61                 u8 da, r2;   /* reserved */
  62                 u8 db, rhrb; /* Receive holding register (b) */
  63                 u8 dc, r3;   /* reserved */
  64                 u8 dd, ip;   /* Input port register of block */
  65                 u8 de, ctg;  /* Start counter timer of block */
  66                 u8 df, cts;  /* Stop counter timer of block */
  67         } __packed r; /* Read access */
  68         struct {
  69                 u8 d0, mra;  /* Mode register 1/2 (a) */
  70                 u8 d1, csra; /* Clock select register (a) */
  71                 u8 d2, cra;  /* Command register (a) */
  72                 u8 d3, thra; /* Transmit holding register (a) */
  73                 u8 d4, acr;  /* Auxiliary control register of block */
  74                 u8 d5, imr;  /* Interrupt mask register of block  */
  75                 u8 d6, ctu;  /* Counter timer upper register of block */
  76                 u8 d7, ctl;  /* Counter timer lower register of block */
  77                 u8 d8, mrb;  /* Mode register 1/2 (b) */
  78                 u8 d9, csrb; /* Clock select register (a) */
  79                 u8 da, crb;  /* Command register (b) */
  80                 u8 db, thrb; /* Transmit holding register (b) */
  81                 u8 dc, r1;   /* reserved */
  82                 u8 dd, opcr; /* Output port configuration register of block */
  83                 u8 de, r2;   /* reserved */
  84                 u8 df, r3;   /* reserved */
  85         } __packed w; /* Write access */
  86 };
  87
  88 #define MR1_CHRL_5_BITS             (0x0 << 0)
  89 #define MR1_CHRL_6_BITS             (0x1 << 0)
  90 #define MR1_CHRL_7_BITS             (0x2 << 0)
  91 #define MR1_CHRL_8_BITS             (0x3 << 0)
  92 #define MR1_PARITY_EVEN             (0x1 << 2)
  93 #define MR1_PARITY_ODD              (0x0 << 2)
  94 #define MR1_PARITY_ON               (0x0 << 3)
  95 #define MR1_PARITY_FORCE            (0x1 << 3)
  96 #define MR1_PARITY_OFF              (0x2 << 3)
  97 #define MR1_PARITY_SPECIAL          (0x3 << 3)
  98 #define MR1_ERROR_CHAR              (0x0 << 5)
  99 #define MR1_ERROR_BLOCK             (0x1 << 5)
 100 #define MR1_RxINT_RxRDY             (0x0 << 6)
 101 #define MR1_RxINT_FFULL             (0x1 << 6)
 102 #define MR1_RxRTS_CONTROL_ON        (0x1 << 7)
 103 #define MR1_RxRTS_CONTROL_OFF       (0x0 << 7)
 104
 105 #define MR2_STOP_BITS_LENGTH_1      (0x7 << 0)
 106 #define MR2_STOP_BITS_LENGTH_2      (0xF << 0)
 107 #define MR2_CTS_ENABLE_TX_ON        (0x1 << 4)
 108 #define MR2_CTS_ENABLE_TX_OFF       (0x0 << 4)
 109 #define MR2_TxRTS_CONTROL_ON        (0x1 << 5)
 110 #define MR2_TxRTS_CONTROL_OFF       (0x0 << 5)
 111 #define MR2_CH_MODE_NORMAL          (0x0 << 6)
 112 #define MR2_CH_MODE_ECHO            (0x1 << 6)
 113 #define MR2_CH_MODE_LOCAL           (0x2 << 6)
 114 #define MR2_CH_MODE_REMOTE          (0x3 << 6)
 115
 116 #define CR_ENABLE_RX                (0x1 << 0)
 117 #define CR_DISABLE_RX               (0x1 << 1)
 118 #define CR_ENABLE_TX                (0x1 << 2)
 119 #define CR_DISABLE_TX               (0x1 << 3)
 120 #define CR_CMD_RESET_MR             (0x1 << 4)
 121 #define CR_CMD_RESET_RX             (0x2 << 4)
 122 #define CR_CMD_RESET_TX             (0x3 << 4)
 123 #define CR_CMD_RESET_ERR_STATUS     (0x4 << 4)
 124 #define CR_CMD_RESET_BREAK_CHANGE   (0x5 << 4)
 125 #define CR_CMD_START_BREAK          (0x6 << 4)
 126 #define CR_CMD_STOP_BREAK           (0x7 << 4)
 127 #define CR_CMD_ASSERT_RTSN          (0x8 << 4)
 128 #define CR_CMD_NEGATE_RTSN          (0x9 << 4)
 129 #define CR_CMD_SET_TIMEOUT_MODE     (0xA << 4)
 130 #define CR_CMD_DISABLE_TIMEOUT_MODE (0xC << 4)
 131
 132 #define SR_RX_READY                 (0x1 << 0)
 133 #define SR_FIFO_FULL                (0x1 << 1)
 134 #define SR_TX_READY                 (0x1 << 2)
 135 #define SR_TX_EMPTY                 (0x1 << 3)
 136 #define SR_OVERRUN_ERROR            (0x1 << 4)
 137 #define SR_PARITY_ERROR             (0x1 << 5)
 138 #define SR_FRAMING_ERROR            (0x1 << 6)
 139 #define SR_RECEIVED_BREAK           (0x1 << 7)
 140
 141 #define SR_ERROR                    (0xF0)
 142
 143 #define ACR_DELTA_IP0_IRQ_EN        (0x1 << 0)
 144 #define ACR_DELTA_IP1_IRQ_EN        (0x1 << 1)
 145 #define ACR_DELTA_IP2_IRQ_EN        (0x1 << 2)
 146 #define ACR_DELTA_IP3_IRQ_EN        (0x1 << 3)
 147 #define ACR_CT_Mask                 (0x7 << 4)
 148 #define ACR_CExt                    (0x0 << 4)
 149 #define ACR_CTxCA                   (0x1 << 4)
 150 #define ACR_CTxCB                   (0x2 << 4)
 151 #define ACR_CClk16                  (0x3 << 4)
 152 #define ACR_TExt                    (0x4 << 4)
 153 #define ACR_TExt16                  (0x5 << 4)
 154 #define ACR_TClk                    (0x6 << 4)
 155 #define ACR_TClk16                  (0x7 << 4)
 156 #define ACR_BRG_SET1                (0x0 << 7)
 157 #define ACR_BRG_SET2                (0x1 << 7)
 158
 159 #define TX_CLK_75                   (0x0 << 0)
 160 #define TX_CLK_110                  (0x1 << 0)
 161 #define TX_CLK_38400                (0x2 << 0)
 162 #define TX_CLK_150                  (0x3 << 0)
 163 #define TX_CLK_300                  (0x4 << 0)
 164 #define TX_CLK_600                  (0x5 << 0)
 165 #define TX_CLK_1200                 (0x6 << 0)
 166 #define TX_CLK_2000                 (0x7 << 0)
 167 #define TX_CLK_2400                 (0x8 << 0)
 168 #define TX_CLK_4800                 (0x9 << 0)
 169 #define TX_CLK_1800                 (0xA << 0)
 170 #define TX_CLK_9600                 (0xB << 0)
 171 #define TX_CLK_19200                (0xC << 0)
 172 #define RX_CLK_75                   (0x0 << 4)
 173 #define RX_CLK_110                  (0x1 << 4)
 174 #define RX_CLK_38400                (0x2 << 4)
 175 #define RX_CLK_150                  (0x3 << 4)
 176 #define RX_CLK_300                  (0x4 << 4)
 177 #define RX_CLK_600                  (0x5 << 4)
 178 #define RX_CLK_1200                 (0x6 << 4)
 179 #define RX_CLK_2000                 (0x7 << 4)
 180 #define RX_CLK_2400                 (0x8 << 4)
 181 #define RX_CLK_4800                 (0x9 << 4)
 182 #define RX_CLK_1800                 (0xA << 4)
 183 #define RX_CLK_9600                 (0xB << 4)
 184 #define RX_CLK_19200                (0xC << 4)
 185
 186 #define OPCR_MPOa_RTSN              (0x0 << 0)
 187 #define OPCR_MPOa_C_TO              (0x1 << 0)
 188 #define OPCR_MPOa_TxC1X             (0x2 << 0)
 189 #define OPCR_MPOa_TxC16X            (0x3 << 0)
 190 #define OPCR_MPOa_RxC1X             (0x4 << 0)
 191 #define OPCR_MPOa_RxC16X            (0x5 << 0)
 192 #define OPCR_MPOa_TxRDY             (0x6 << 0)
 193 #define OPCR_MPOa_RxRDY_FF          (0x7 << 0)
 194
 195 #define OPCR_MPOb_RTSN              (0x0 << 4)
 196 #define OPCR_MPOb_C_TO              (0x1 << 4)
 197 #define OPCR_MPOb_TxC1X             (0x2 << 4)
 198 #define OPCR_MPOb_TxC16X            (0x3 << 4)
 199 #define OPCR_MPOb_RxC1X             (0x4 << 4)
 200 #define OPCR_MPOb_RxC16X            (0x5 << 4)
 201 #define OPCR_MPOb_TxRDY             (0x6 << 4)
 202 #define OPCR_MPOb_RxRDY_FF          (0x7 << 4)
 203
 204 #define OPCR_MPP_INPUT              (0x0 << 7)
 205 #define OPCR_MPP_OUTPUT             (0x1 << 7)
 206
 207 #define IMR_TxRDY_A                 (0x1 << 0)
 208 #define IMR_RxRDY_FFULL_A           (0x1 << 1)
 209 #define IMR_DELTA_BREAK_A           (0x1 << 2)
 210 #define IMR_COUNTER_READY           (0x1 << 3)
 211 #define IMR_TxRDY_B                 (0x1 << 4)
 212 #define IMR_RxRDY_FFULL_B           (0x1 << 5)
 213 #define IMR_DELTA_BREAK_B           (0x1 << 6)
 214 #define IMR_INPUT_PORT_CHANGE       (0x1 << 7)
 215
 216 #define ISR_TxRDY_A                 (0x1 << 0)
 217 #define ISR_RxRDY_FFULL_A           (0x1 << 1)
 218 #define ISR_DELTA_BREAK_A           (0x1 << 2)
 219 #define ISR_COUNTER_READY           (0x1 << 3)
 220 #define ISR_TxRDY_B                 (0x1 << 4)
 221 #define ISR_RxRDY_FFULL_B           (0x1 << 5)
 222 #define ISR_DELTA_BREAK_B           (0x1 << 6)
 223 #define ISR_INPUT_PORT_CHANGE       (0x1 << 7)
 224
 225 #define ACK_INT_REQ0                    0
 226 #define ACK_INT_REQ1                    2
 227
 228 #endif /* SCC2698_H_ */