iwmc3200wifi: Implement cfg80211 PMKSA API

[linux/fpc-iii.git] / drivers / serial / serial_core.c

/*
 *  linux/drivers/char/core.c
 *
 *  Driver core for serial ports
 *
 *  Based on drivers/char/serial.c, by Linus Torvalds, Theodore Ts'o.
 *
 *  Copyright 1999 ARM Limited
 *  Copyright (C) 2000-2001 Deep Blue Solutions Ltd.
 *
 * This program is free software; you can redistribute it and/or modify
 * it under the terms of the GNU General Public License as published by
 * the Free Software Foundation; either version 2 of the License, or
 * (at your option) any later version.
 *
 * This program is distributed in the hope that it will be useful,
 * but WITHOUT ANY WARRANTY; without even the implied warranty of
 * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
 * GNU General Public License for more details.
 *
 * You should have received a copy of the GNU General Public License
 * along with this program; if not, write to the Free Software
 * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA  02111-1307  USA
 */
#include <linux/module.h>
#include <linux/tty.h>
#include <linux/slab.h>
#include <linux/init.h>
#include <linux/console.h>
#include <linux/proc_fs.h>
#include <linux/seq_file.h>
#include <linux/smp_lock.h>
#include <linux/device.h>
#include <linux/serial.h> /* for serial_state and serial_icounter_struct */
#include <linux/serial_core.h>
#include <linux/delay.h>
#include <linux/mutex.h>

#include <asm/irq.h>
#include <asm/uaccess.h>

/*
 * This is used to lock changes in serial line configuration.
 */
static DEFINE_MUTEX(port_mutex);

/*
 * lockdep: port->lock is initialized in two places, but we
 *          want only one lock-class:
 */
static struct lock_class_key port_lock_key;

#define HIGH_BITS_OFFSET        ((sizeof(long)-sizeof(int))*8)

#ifdef CONFIG_SERIAL_CORE_CONSOLE
#define uart_console(port)      ((port)->cons && (port)->cons->index == (port)->line)
#else
#define uart_console(port)      (0)
#endif

static void uart_change_speed(struct uart_state *state,
                                        struct ktermios *old_termios);
static void uart_wait_until_sent(struct tty_struct *tty, int timeout);
static void uart_change_pm(struct uart_state *state, int pm_state);

/*
 * This routine is used by the interrupt handler to schedule processing in
 * the software interrupt portion of the driver.
 */
void uart_write_wakeup(struct uart_port *port)
{
        struct uart_state *state = port->state;
        /*
         * This means you called this function _after_ the port was
         * closed.  No cookie for you.
         */
        BUG_ON(!state);
        tasklet_schedule(&state->tlet);
}

static void uart_stop(struct tty_struct *tty)
{
        struct uart_state *state = tty->driver_data;
        struct uart_port *port = state->uart_port;
        unsigned long flags;

        spin_lock_irqsave(&port->lock, flags);
        port->ops->stop_tx(port);
        spin_unlock_irqrestore(&port->lock, flags);
}

static void __uart_start(struct tty_struct *tty)
{
        struct uart_state *state = tty->driver_data;
        struct uart_port *port = state->uart_port;

        if (!uart_circ_empty(&state->xmit) && state->xmit.buf &&
            !tty->stopped && !tty->hw_stopped)
                port->ops->start_tx(port);
}

static void uart_start(struct tty_struct *tty)
{
        struct uart_state *state = tty->driver_data;
        struct uart_port *port = state->uart_port;
        unsigned long flags;

        spin_lock_irqsave(&port->lock, flags);
        __uart_start(tty);
        spin_unlock_irqrestore(&port->lock, flags);
}

static void uart_tasklet_action(unsigned long data)
{
        struct uart_state *state = (struct uart_state *)data;
        tty_wakeup(state->port.tty);
}

static inline void
uart_update_mctrl(struct uart_port *port, unsigned int set, unsigned int clear)
{
        unsigned long flags;
        unsigned int old;

        spin_lock_irqsave(&port->lock, flags);
        old = port->mctrl;
        port->mctrl = (old & ~clear) | set;
        if (old != port->mctrl)
                port->ops->set_mctrl(port, port->mctrl);
        spin_unlock_irqrestore(&port->lock, flags);
}

#define uart_set_mctrl(port, set)       uart_update_mctrl(port, set, 0)
#define uart_clear_mctrl(port, clear)   uart_update_mctrl(port, 0, clear)

/*
 * Startup the port.  This will be called once per open.  All calls
 * will be serialised by the per-port mutex.
 */
static int uart_startup(struct uart_state *state, int init_hw)
{
        struct uart_port *uport = state->uart_port;
        struct tty_port *port = &state->port;
        unsigned long page;
        int retval = 0;

        if (port->flags & ASYNC_INITIALIZED)
                return 0;

        /*
         * Set the TTY IO error marker - we will only clear this
         * once we have successfully opened the port.  Also set
         * up the tty->alt_speed kludge
         */
        set_bit(TTY_IO_ERROR, &port->tty->flags);

        if (uport->type == PORT_UNKNOWN)
                return 0;

        /*
         * Initialise and allocate the transmit and temporary
         * buffer.
         */
        if (!state->xmit.buf) {
                /* This is protected by the per port mutex */
                page = get_zeroed_page(GFP_KERNEL);
                if (!page)
                        return -ENOMEM;

                state->xmit.buf = (unsigned char *) page;
                uart_circ_clear(&state->xmit);
        }

        retval = uport->ops->startup(uport);
        if (retval == 0) {
                if (init_hw) {
                        /*
                         * Initialise the hardware port settings.
                         */
                        uart_change_speed(state, NULL);

                        /*
                         * Setup the RTS and DTR signals once the
                         * port is open and ready to respond.
                         */
                        if (port->tty->termios->c_cflag & CBAUD)
                                uart_set_mctrl(uport, TIOCM_RTS | TIOCM_DTR);
                }

                if (port->flags & ASYNC_CTS_FLOW) {
                        spin_lock_irq(&uport->lock);
                        if (!(uport->ops->get_mctrl(uport) & TIOCM_CTS))
                                port->tty->hw_stopped = 1;
                        spin_unlock_irq(&uport->lock);
                }

                set_bit(ASYNCB_INITIALIZED, &port->flags);

                clear_bit(TTY_IO_ERROR, &port->tty->flags);
        }

        if (retval && capable(CAP_SYS_ADMIN))
                retval = 0;

        return retval;
}

/*
 * This routine will shutdown a serial port; interrupts are disabled, and
 * DTR is dropped if the hangup on close termio flag is on.  Calls to
 * uart_shutdown are serialised by the per-port semaphore.
 */
static void uart_shutdown(struct uart_state *state)
{
        struct uart_port *uport = state->uart_port;
        struct tty_port *port = &state->port;
        struct tty_struct *tty = port->tty;

        /*
         * Set the TTY IO error marker
         */
        if (tty)
                set_bit(TTY_IO_ERROR, &tty->flags);

        if (test_and_clear_bit(ASYNCB_INITIALIZED, &port->flags)) {
                /*
                 * Turn off DTR and RTS early.
                 */
                if (!tty || (tty->termios->c_cflag & HUPCL))
                        uart_clear_mctrl(uport, TIOCM_DTR | TIOCM_RTS);

                /*
                 * clear delta_msr_wait queue to avoid mem leaks: we may free
                 * the irq here so the queue might never be woken up.  Note
                 * that we won't end up waiting on delta_msr_wait again since
                 * any outstanding file descriptors should be pointing at
                 * hung_up_tty_fops now.
                 */
                wake_up_interruptible(&port->delta_msr_wait);

                /*
                 * Free the IRQ and disable the port.
                 */
                uport->ops->shutdown(uport);

                /*
                 * Ensure that the IRQ handler isn't running on another CPU.
                 */
                synchronize_irq(uport->irq);
        }

        /*
         * kill off our tasklet
         */
        tasklet_kill(&state->tlet);

        /*
         * Free the transmit buffer page.
         */
        if (state->xmit.buf) {
                free_page((unsigned long)state->xmit.buf);
                state->xmit.buf = NULL;
        }
}

/**
 *      uart_update_timeout - update per-port FIFO timeout.
 *      @port:  uart_port structure describing the port
 *      @cflag: termios cflag value
 *      @baud:  speed of the port
 *
 *      Set the port FIFO timeout value.  The @cflag value should
 *      reflect the actual hardware settings.
 */
void
uart_update_timeout(struct uart_port *port, unsigned int cflag,
                    unsigned int baud)
{
        unsigned int bits;

        /* byte size and parity */
        switch (cflag & CSIZE) {
        case CS5:
                bits = 7;
                break;
        case CS6:
                bits = 8;
                break;
        case CS7:
                bits = 9;
                break;
        default:
                bits = 10;
                break; /* CS8 */
        }

        if (cflag & CSTOPB)
                bits++;
        if (cflag & PARENB)
                bits++;

        /*
         * The total number of bits to be transmitted in the fifo.
         */
        bits = bits * port->fifosize;

        /*
         * Figure the timeout to send the above number of bits.
         * Add .02 seconds of slop
         */
        port->timeout = (HZ * bits) / baud + HZ/50;
}

EXPORT_SYMBOL(uart_update_timeout);

/**
 *      uart_get_baud_rate - return baud rate for a particular port
 *      @port: uart_port structure describing the port in question.
 *      @termios: desired termios settings.
 *      @old: old termios (or NULL)
 *      @min: minimum acceptable baud rate
 *      @max: maximum acceptable baud rate
 *
 *      Decode the termios structure into a numeric baud rate,
 *      taking account of the magic 38400 baud rate (with spd_*
 *      flags), and mapping the %B0 rate to 9600 baud.
 *
 *      If the new baud rate is invalid, try the old termios setting.
 *      If it's still invalid, we try 9600 baud.
 *
 *      Update the @termios structure to reflect the baud rate
 *      we're actually going to be using. Don't do this for the case
 *      where B0 is requested ("hang up").
 */
unsigned int
uart_get_baud_rate(struct uart_port *port, struct ktermios *termios,
                   struct ktermios *old, unsigned int min, unsigned int max)
{
        unsigned int try, baud, altbaud = 38400;
        int hung_up = 0;
        upf_t flags = port->flags & UPF_SPD_MASK;

        if (flags == UPF_SPD_HI)
                altbaud = 57600;
        if (flags == UPF_SPD_VHI)
                altbaud = 115200;
        if (flags == UPF_SPD_SHI)
                altbaud = 230400;
        if (flags == UPF_SPD_WARP)
                altbaud = 460800;

        for (try = 0; try < 2; try++) {
                baud = tty_termios_baud_rate(termios);

                /*
                 * The spd_hi, spd_vhi, spd_shi, spd_warp kludge...
                 * Die! Die! Die!
                 */
                if (baud == 38400)
                        baud = altbaud;

                /*
                 * Special case: B0 rate.
                 */
                if (baud == 0) {
                        hung_up = 1;
                        baud = 9600;
                }

                if (baud >= min && baud <= max)
                        return baud;

                /*
                 * Oops, the quotient was zero.  Try again with
                 * the old baud rate if possible.
                 */
                termios->c_cflag &= ~CBAUD;
                if (old) {
                        baud = tty_termios_baud_rate(old);
                        if (!hung_up)
                                tty_termios_encode_baud_rate(termios,
                                                                baud, baud);
                        old = NULL;
                        continue;
                }

                /*
                 * As a last resort, if the quotient is zero,
                 * default to 9600 bps
                 */
                if (!hung_up)
                        tty_termios_encode_baud_rate(termios, 9600, 9600);
        }

        return 0;
}

EXPORT_SYMBOL(uart_get_baud_rate);

/**
 *      uart_get_divisor - return uart clock divisor
 *      @port: uart_port structure describing the port.
 *      @baud: desired baud rate
 *
 *      Calculate the uart clock divisor for the port.
 */
unsigned int
uart_get_divisor(struct uart_port *port, unsigned int baud)
{
        unsigned int quot;

        /*
         * Old custom speed handling.
         */
        if (baud == 38400 && (port->flags & UPF_SPD_MASK) == UPF_SPD_CUST)
                quot = port->custom_divisor;
        else
                quot = (port->uartclk + (8 * baud)) / (16 * baud);

        return quot;
}

EXPORT_SYMBOL(uart_get_divisor);

/* FIXME: Consistent locking policy */
static void
uart_change_speed(struct uart_state *state, struct ktermios *old_termios)
{
        struct tty_port *port = &state->port;
        struct tty_struct *tty = port->tty;
        struct uart_port *uport = state->uart_port;
        struct ktermios *termios;

        /*
         * If we have no tty, termios, or the port does not exist,
         * then we can't set the parameters for this port.
         */
        if (!tty || !tty->termios || uport->type == PORT_UNKNOWN)
                return;

        termios = tty->termios;

        /*
         * Set flags based on termios cflag
         */
        if (termios->c_cflag & CRTSCTS)
                set_bit(ASYNCB_CTS_FLOW, &port->flags);
        else
                clear_bit(ASYNCB_CTS_FLOW, &port->flags);

        if (termios->c_cflag & CLOCAL)
                clear_bit(ASYNCB_CHECK_CD, &port->flags);
        else
                set_bit(ASYNCB_CHECK_CD, &port->flags);

        uport->ops->set_termios(uport, termios, old_termios);
}

static inline int
__uart_put_char(struct uart_port *port, struct circ_buf *circ, unsigned char c)
{
        unsigned long flags;
        int ret = 0;

        if (!circ->buf)
                return 0;

        spin_lock_irqsave(&port->lock, flags);
        if (uart_circ_chars_free(circ) != 0) {
                circ->buf[circ->head] = c;
                circ->head = (circ->head + 1) & (UART_XMIT_SIZE - 1);
                ret = 1;
        }
        spin_unlock_irqrestore(&port->lock, flags);
        return ret;
}

static int uart_put_char(struct tty_struct *tty, unsigned char ch)
{
        struct uart_state *state = tty->driver_data;

        return __uart_put_char(state->uart_port, &state->xmit, ch);
}

static void uart_flush_chars(struct tty_struct *tty)
{
        uart_start(tty);
}

static int
uart_write(struct tty_struct *tty, const unsigned char *buf, int count)
{
        struct uart_state *state = tty->driver_data;
        struct uart_port *port;
        struct circ_buf *circ;
        unsigned long flags;
        int c, ret = 0;

        /*
         * This means you called this function _after_ the port was
         * closed.  No cookie for you.
         */
        if (!state) {
                WARN_ON(1);
                return -EL3HLT;
        }

        port = state->uart_port;
        circ = &state->xmit;

        if (!circ->buf)
                return 0;

        spin_lock_irqsave(&port->lock, flags);
        while (1) {
                c = CIRC_SPACE_TO_END(circ->head, circ->tail, UART_XMIT_SIZE);
                if (count < c)
                        c = count;
                if (c <= 0)
                        break;
                memcpy(circ->buf + circ->head, buf, c);
                circ->head = (circ->head + c) & (UART_XMIT_SIZE - 1);
                buf += c;
                count -= c;
                ret += c;
        }
        spin_unlock_irqrestore(&port->lock, flags);

        uart_start(tty);
        return ret;
}

static int uart_write_room(struct tty_struct *tty)
{
        struct uart_state *state = tty->driver_data;
        unsigned long flags;
        int ret;

        spin_lock_irqsave(&state->uart_port->lock, flags);
        ret = uart_circ_chars_free(&state->xmit);
        spin_unlock_irqrestore(&state->uart_port->lock, flags);
        return ret;
}

static int uart_chars_in_buffer(struct tty_struct *tty)
{
        struct uart_state *state = tty->driver_data;
        unsigned long flags;
        int ret;

        spin_lock_irqsave(&state->uart_port->lock, flags);
        ret = uart_circ_chars_pending(&state->xmit);
        spin_unlock_irqrestore(&state->uart_port->lock, flags);
        return ret;
}

static void uart_flush_buffer(struct tty_struct *tty)
{
        struct uart_state *state = tty->driver_data;
        struct uart_port *port;
        unsigned long flags;

        /*
         * This means you called this function _after_ the port was
         * closed.  No cookie for you.
         */
        if (!state) {
                WARN_ON(1);
                return;
        }

        port = state->uart_port;
        pr_debug("uart_flush_buffer(%d) called\n", tty->index);

        spin_lock_irqsave(&port->lock, flags);
        uart_circ_clear(&state->xmit);
        if (port->ops->flush_buffer)
                port->ops->flush_buffer(port);
        spin_unlock_irqrestore(&port->lock, flags);
        tty_wakeup(tty);
}

/*
 * This function is used to send a high-priority XON/XOFF character to
 * the device
 */
static void uart_send_xchar(struct tty_struct *tty, char ch)
{
        struct uart_state *state = tty->driver_data;
        struct uart_port *port = state->uart_port;
        unsigned long flags;

        if (port->ops->send_xchar)
                port->ops->send_xchar(port, ch);
        else {
                port->x_char = ch;
                if (ch) {
                        spin_lock_irqsave(&port->lock, flags);
                        port->ops->start_tx(port);
                        spin_unlock_irqrestore(&port->lock, flags);
                }
        }
}

static void uart_throttle(struct tty_struct *tty)
{
        struct uart_state *state = tty->driver_data;

        if (I_IXOFF(tty))
                uart_send_xchar(tty, STOP_CHAR(tty));

        if (tty->termios->c_cflag & CRTSCTS)
                uart_clear_mctrl(state->uart_port, TIOCM_RTS);
}

static void uart_unthrottle(struct tty_struct *tty)
{
        struct uart_state *state = tty->driver_data;
        struct uart_port *port = state->uart_port;

        if (I_IXOFF(tty)) {
                if (port->x_char)
                        port->x_char = 0;
                else
                        uart_send_xchar(tty, START_CHAR(tty));
        }

        if (tty->termios->c_cflag & CRTSCTS)
                uart_set_mctrl(port, TIOCM_RTS);
}

static int uart_get_info(struct uart_state *state,
                         struct serial_struct __user *retinfo)
{
        struct uart_port *uport = state->uart_port;
        struct tty_port *port = &state->port;
        struct serial_struct tmp;

        memset(&tmp, 0, sizeof(tmp));

        /* Ensure the state we copy is consistent and no hardware changes
           occur as we go */
        mutex_lock(&port->mutex);

        tmp.type            = uport->type;
        tmp.line            = uport->line;
        tmp.port            = uport->iobase;
        if (HIGH_BITS_OFFSET)
                tmp.port_high = (long) uport->iobase >> HIGH_BITS_OFFSET;
        tmp.irq             = uport->irq;
        tmp.flags           = uport->flags;
        tmp.xmit_fifo_size  = uport->fifosize;
        tmp.baud_base       = uport->uartclk / 16;
        tmp.close_delay     = port->close_delay / 10;
        tmp.closing_wait    = port->closing_wait == ASYNC_CLOSING_WAIT_NONE ?
                                ASYNC_CLOSING_WAIT_NONE :
                                port->closing_wait / 10;
        tmp.custom_divisor  = uport->custom_divisor;
        tmp.hub6            = uport->hub6;
        tmp.io_type         = uport->iotype;
        tmp.iomem_reg_shift = uport->regshift;
        tmp.iomem_base      = (void *)(unsigned long)uport->mapbase;

        mutex_unlock(&port->mutex);

        if (copy_to_user(retinfo, &tmp, sizeof(*retinfo)))
                return -EFAULT;
        return 0;
}

static int uart_set_info(struct uart_state *state,
                         struct serial_struct __user *newinfo)
{
        struct serial_struct new_serial;
        struct uart_port *uport = state->uart_port;
        struct tty_port *port = &state->port;
        unsigned long new_port;
        unsigned int change_irq, change_port, closing_wait;
        unsigned int old_custom_divisor, close_delay;
        upf_t old_flags, new_flags;
        int retval = 0;

        if (copy_from_user(&new_serial, newinfo, sizeof(new_serial)))
                return -EFAULT;

        new_port = new_serial.port;
        if (HIGH_BITS_OFFSET)
                new_port += (unsigned long) new_serial.port_high << HIGH_BITS_OFFSET;

        new_serial.irq = irq_canonicalize(new_serial.irq);
        close_delay = new_serial.close_delay * 10;
        closing_wait = new_serial.closing_wait == ASYNC_CLOSING_WAIT_NONE ?
                        ASYNC_CLOSING_WAIT_NONE : new_serial.closing_wait * 10;

        /*
         * This semaphore protects port->count.  It is also
         * very useful to prevent opens.  Also, take the
         * port configuration semaphore to make sure that a
         * module insertion/removal doesn't change anything
         * under us.
         */
        mutex_lock(&port->mutex);

        change_irq  = !(uport->flags & UPF_FIXED_PORT)
                && new_serial.irq != uport->irq;

        /*
         * Since changing the 'type' of the port changes its resource
         * allocations, we should treat type changes the same as
         * IO port changes.
         */
        change_port = !(uport->flags & UPF_FIXED_PORT)
                && (new_port != uport->iobase ||
                    (unsigned long)new_serial.iomem_base != uport->mapbase ||
                    new_serial.hub6 != uport->hub6 ||
                    new_serial.io_type != uport->iotype ||
                    new_serial.iomem_reg_shift != uport->regshift ||
                    new_serial.type != uport->type);

        old_flags = uport->flags;
        new_flags = new_serial.flags;
        old_custom_divisor = uport->custom_divisor;

        if (!capable(CAP_SYS_ADMIN)) {
                retval = -EPERM;
                if (change_irq || change_port ||
                    (new_serial.baud_base != uport->uartclk / 16) ||
                    (close_delay != port->close_delay) ||
                    (closing_wait != port->closing_wait) ||
                    (new_serial.xmit_fifo_size &&
                     new_serial.xmit_fifo_size != uport->fifosize) ||
                    (((new_flags ^ old_flags) & ~UPF_USR_MASK) != 0))
                        goto exit;
                uport->flags = ((uport->flags & ~UPF_USR_MASK) |
                               (new_flags & UPF_USR_MASK));
                uport->custom_divisor = new_serial.custom_divisor;
                goto check_and_exit;
        }

        /*
         * Ask the low level driver to verify the settings.
         */
        if (uport->ops->verify_port)
                retval = uport->ops->verify_port(uport, &new_serial);

        if ((new_serial.irq >= nr_irqs) || (new_serial.irq < 0) ||
            (new_serial.baud_base < 9600))
                retval = -EINVAL;

        if (retval)
                goto exit;

        if (change_port || change_irq) {
                retval = -EBUSY;

                /*
                 * Make sure that we are the sole user of this port.
                 */
                if (tty_port_users(port) > 1)
                        goto exit;

                /*
                 * We need to shutdown the serial port at the old
                 * port/type/irq combination.
                 */
                uart_shutdown(state);
        }

        if (change_port) {
                unsigned long old_iobase, old_mapbase;
                unsigned int old_type, old_iotype, old_hub6, old_shift;

                old_iobase = uport->iobase;
                old_mapbase = uport->mapbase;
                old_type = uport->type;
                old_hub6 = uport->hub6;
                old_iotype = uport->iotype;
                old_shift = uport->regshift;

                /*
                 * Free and release old regions
                 */
                if (old_type != PORT_UNKNOWN)
                        uport->ops->release_port(uport);

                uport->iobase = new_port;
                uport->type = new_serial.type;
                uport->hub6 = new_serial.hub6;
                uport->iotype = new_serial.io_type;
                uport->regshift = new_serial.iomem_reg_shift;
                uport->mapbase = (unsigned long)new_serial.iomem_base;

                /*
                 * Claim and map the new regions
                 */
                if (uport->type != PORT_UNKNOWN) {
                        retval = uport->ops->request_port(uport);
                } else {
                        /* Always success - Jean II */
                        retval = 0;
                }

                /*
                 * If we fail to request resources for the
                 * new port, try to restore the old settings.
                 */
                if (retval && old_type != PORT_UNKNOWN) {
                        uport->iobase = old_iobase;
                        uport->type = old_type;
                        uport->hub6 = old_hub6;
                        uport->iotype = old_iotype;
                        uport->regshift = old_shift;
                        uport->mapbase = old_mapbase;
                        retval = uport->ops->request_port(uport);
                        /*
                         * If we failed to restore the old settings,
                         * we fail like this.
                         */
                        if (retval)
                                uport->type = PORT_UNKNOWN;

                        /*
                         * We failed anyway.
                         */
                        retval = -EBUSY;
                        /* Added to return the correct error -Ram Gupta */
                        goto exit;
                }
        }

        if (change_irq)
                uport->irq      = new_serial.irq;
        if (!(uport->flags & UPF_FIXED_PORT))
                uport->uartclk  = new_serial.baud_base * 16;
        uport->flags            = (uport->flags & ~UPF_CHANGE_MASK) |
                                 (new_flags & UPF_CHANGE_MASK);
        uport->custom_divisor   = new_serial.custom_divisor;
        port->close_delay     = close_delay;
        port->closing_wait    = closing_wait;
        if (new_serial.xmit_fifo_size)
                uport->fifosize = new_serial.xmit_fifo_size;
        if (port->tty)
                port->tty->low_latency =
                        (uport->flags & UPF_LOW_LATENCY) ? 1 : 0;

 check_and_exit:
        retval = 0;
        if (uport->type == PORT_UNKNOWN)
                goto exit;
        if (port->flags & ASYNC_INITIALIZED) {
                if (((old_flags ^ uport->flags) & UPF_SPD_MASK) ||
                    old_custom_divisor != uport->custom_divisor) {
                        /*
                         * If they're setting up a custom divisor or speed,
                         * instead of clearing it, then bitch about it. No
                         * need to rate-limit; it's CAP_SYS_ADMIN only.
                         */
                        if (uport->flags & UPF_SPD_MASK) {
                                char buf[64];
                                printk(KERN_NOTICE
                                       "%s sets custom speed on %s. This "
                                       "is deprecated.\n", current->comm,
                                       tty_name(port->tty, buf));
                        }
                        uart_change_speed(state, NULL);
                }
        } else
                retval = uart_startup(state, 1);
 exit:
        mutex_unlock(&port->mutex);
        return retval;
}


/*
 * uart_get_lsr_info - get line status register info.
 * Note: uart_ioctl protects us against hangups.
 */
static int uart_get_lsr_info(struct uart_state *state,
                             unsigned int __user *value)
{
        struct uart_port *uport = state->uart_port;
        struct tty_port *port = &state->port;
        unsigned int result;

        result = uport->ops->tx_empty(uport);

        /*
         * If we're about to load something into the transmit
         * register, we'll pretend the transmitter isn't empty to
         * avoid a race condition (depending on when the transmit
         * interrupt happens).
         */
        if (uport->x_char ||
            ((uart_circ_chars_pending(&state->xmit) > 0) &&
             !port->tty->stopped && !port->tty->hw_stopped))
                result &= ~TIOCSER_TEMT;

        return put_user(result, value);
}

static int uart_tiocmget(struct tty_struct *tty, struct file *file)
{
        struct uart_state *state = tty->driver_data;
        struct tty_port *port = &state->port;
        struct uart_port *uport = state->uart_port;
        int result = -EIO;

        mutex_lock(&port->mutex);
        if ((!file || !tty_hung_up_p(file)) &&
            !(tty->flags & (1 << TTY_IO_ERROR))) {
                result = uport->mctrl;

                spin_lock_irq(&uport->lock);
                result |= uport->ops->get_mctrl(uport);
                spin_unlock_irq(&uport->lock);
        }
        mutex_unlock(&port->mutex);

        return result;
}

static int
uart_tiocmset(struct tty_struct *tty, struct file *file,
              unsigned int set, unsigned int clear)
{
        struct uart_state *state = tty->driver_data;
        struct uart_port *uport = state->uart_port;
        struct tty_port *port = &state->port;
        int ret = -EIO;

        mutex_lock(&port->mutex);
        if ((!file || !tty_hung_up_p(file)) &&
            !(tty->flags & (1 << TTY_IO_ERROR))) {
                uart_update_mctrl(uport, set, clear);
                ret = 0;
        }
        mutex_unlock(&port->mutex);
        return ret;
}

static int uart_break_ctl(struct tty_struct *tty, int break_state)
{
        struct uart_state *state = tty->driver_data;
        struct tty_port *port = &state->port;
        struct uart_port *uport = state->uart_port;

        mutex_lock(&port->mutex);

        if (uport->type != PORT_UNKNOWN)
                uport->ops->break_ctl(uport, break_state);

        mutex_unlock(&port->mutex);
        return 0;
}

static int uart_do_autoconfig(struct uart_state *state)
{
        struct uart_port *uport = state->uart_port;
        struct tty_port *port = &state->port;
        int flags, ret;

        if (!capable(CAP_SYS_ADMIN))
                return -EPERM;

        /*
         * Take the per-port semaphore.  This prevents count from
         * changing, and hence any extra opens of the port while
         * we're auto-configuring.
         */
        if (mutex_lock_interruptible(&port->mutex))
                return -ERESTARTSYS;

        ret = -EBUSY;
        if (tty_port_users(port) == 1) {
                uart_shutdown(state);

                /*
                 * If we already have a port type configured,
                 * we must release its resources.
                 */
                if (uport->type != PORT_UNKNOWN)
                        uport->ops->release_port(uport);

                flags = UART_CONFIG_TYPE;
                if (uport->flags & UPF_AUTO_IRQ)
                        flags |= UART_CONFIG_IRQ;

                /*
                 * This will claim the ports resources if
                 * a port is found.
                 */
                uport->ops->config_port(uport, flags);

                ret = uart_startup(state, 1);
        }
        mutex_unlock(&port->mutex);
        return ret;
}

/*
 * Wait for any of the 4 modem inputs (DCD,RI,DSR,CTS) to change
 * - mask passed in arg for lines of interest
 *   (use |'ed TIOCM_RNG/DSR/CD/CTS for masking)
 * Caller should use TIOCGICOUNT to see which one it was
 *
 * FIXME: This wants extracting into a common all driver implementation
 * of TIOCMWAIT using tty_port.
 */
static int
uart_wait_modem_status(struct uart_state *state, unsigned long arg)
{
        struct uart_port *uport = state->uart_port;
        struct tty_port *port = &state->port;
        DECLARE_WAITQUEUE(wait, current);
        struct uart_icount cprev, cnow;
        int ret;

        /*
         * note the counters on entry
         */
        spin_lock_irq(&uport->lock);
        memcpy(&cprev, &uport->icount, sizeof(struct uart_icount));

        /*
         * Force modem status interrupts on
         */
        uport->ops->enable_ms(uport);
        spin_unlock_irq(&uport->lock);

        add_wait_queue(&port->delta_msr_wait, &wait);
        for (;;) {
                spin_lock_irq(&uport->lock);
                memcpy(&cnow, &uport->icount, sizeof(struct uart_icount));
                spin_unlock_irq(&uport->lock);

                set_current_state(TASK_INTERRUPTIBLE);

                if (((arg & TIOCM_RNG) && (cnow.rng != cprev.rng)) ||
                    ((arg & TIOCM_DSR) && (cnow.dsr != cprev.dsr)) ||
                    ((arg & TIOCM_CD)  && (cnow.dcd != cprev.dcd)) ||
                    ((arg & TIOCM_CTS) && (cnow.cts != cprev.cts))) {
                        ret = 0;
                        break;
                }

                schedule();

                /* see if a signal did it */
                if (signal_pending(current)) {
                        ret = -ERESTARTSYS;
                        break;
                }

                cprev = cnow;
        }

        current->state = TASK_RUNNING;
        remove_wait_queue(&port->delta_msr_wait, &wait);

        return ret;
}

/*
 * Get counter of input serial line interrupts (DCD,RI,DSR,CTS)
 * Return: write counters to the user passed counter struct
 * NB: both 1->0 and 0->1 transitions are counted except for
 *     RI where only 0->1 is counted.
 */
static int uart_get_count(struct uart_state *state,
                          struct serial_icounter_struct __user *icnt)
{
        struct serial_icounter_struct icount;
        struct uart_icount cnow;
        struct uart_port *uport = state->uart_port;

        spin_lock_irq(&uport->lock);
        memcpy(&cnow, &uport->icount, sizeof(struct uart_icount));
        spin_unlock_irq(&uport->lock);

        icount.cts         = cnow.cts;
        icount.dsr         = cnow.dsr;
        icount.rng         = cnow.rng;
        icount.dcd         = cnow.dcd;
        icount.rx          = cnow.rx;
        icount.tx          = cnow.tx;
        icount.frame       = cnow.frame;
        icount.overrun     = cnow.overrun;
        icount.parity      = cnow.parity;
        icount.brk         = cnow.brk;
        icount.buf_overrun = cnow.buf_overrun;

        return copy_to_user(icnt, &icount, sizeof(icount)) ? -EFAULT : 0;
}

/*
 * Called via sys_ioctl.  We can use spin_lock_irq() here.
 */
static int
uart_ioctl(struct tty_struct *tty, struct file *filp, unsigned int cmd,
           unsigned long arg)
{
        struct uart_state *state = tty->driver_data;
        struct tty_port *port = &state->port;
        void __user *uarg = (void __user *)arg;
        int ret = -ENOIOCTLCMD;


        /*
         * These ioctls don't rely on the hardware to be present.
         */
        switch (cmd) {
        case TIOCGSERIAL:
                ret = uart_get_info(state, uarg);
                break;

        case TIOCSSERIAL:
                ret = uart_set_info(state, uarg);
                break;

        case TIOCSERCONFIG:
                ret = uart_do_autoconfig(state);
                break;

        case TIOCSERGWILD: /* obsolete */
        case TIOCSERSWILD: /* obsolete */
                ret = 0;
                break;
        }

        if (ret != -ENOIOCTLCMD)
                goto out;

        if (tty->flags & (1 << TTY_IO_ERROR)) {
                ret = -EIO;
                goto out;
        }

        /*
         * The following should only be used when hardware is present.
         */
        switch (cmd) {
        case TIOCMIWAIT:
                ret = uart_wait_modem_status(state, arg);
                break;

        case TIOCGICOUNT:
                ret = uart_get_count(state, uarg);
                break;
        }

        if (ret != -ENOIOCTLCMD)
                goto out;

        mutex_lock(&port->mutex);

        if (tty_hung_up_p(filp)) {
                ret = -EIO;
                goto out_up;
        }

        /*
         * All these rely on hardware being present and need to be
         * protected against the tty being hung up.
         */
        switch (cmd) {
        case TIOCSERGETLSR: /* Get line status register */
                ret = uart_get_lsr_info(state, uarg);
                break;

        default: {
                struct uart_port *uport = state->uart_port;
                if (uport->ops->ioctl)
                        ret = uport->ops->ioctl(uport, cmd, arg);
                break;
        }
        }
out_up:
        mutex_unlock(&port->mutex);
out:
        return ret;
}

static void uart_set_ldisc(struct tty_struct *tty)
{
        struct uart_state *state = tty->driver_data;
        struct uart_port *uport = state->uart_port;

        if (uport->ops->set_ldisc)
                uport->ops->set_ldisc(uport);
}

static void uart_set_termios(struct tty_struct *tty,
                                                struct ktermios *old_termios)
{
        struct uart_state *state = tty->driver_data;
        unsigned long flags;
        unsigned int cflag = tty->termios->c_cflag;


        /*
         * These are the bits that are used to setup various
         * flags in the low level driver. We can ignore the Bfoo
         * bits in c_cflag; c_[io]speed will always be set
         * appropriately by set_termios() in tty_ioctl.c
         */
#define RELEVANT_IFLAG(iflag)   ((iflag) & (IGNBRK|BRKINT|IGNPAR|PARMRK|INPCK))
        if ((cflag ^ old_termios->c_cflag) == 0 &&
            tty->termios->c_ospeed == old_termios->c_ospeed &&
            tty->termios->c_ispeed == old_termios->c_ispeed &&
            RELEVANT_IFLAG(tty->termios->c_iflag ^ old_termios->c_iflag) == 0) {
                return;
        }

        uart_change_speed(state, old_termios);

        /* Handle transition to B0 status */
        if ((old_termios->c_cflag & CBAUD) && !(cflag & CBAUD))
                uart_clear_mctrl(state->uart_port, TIOCM_RTS | TIOCM_DTR);

        /* Handle transition away from B0 status */
        if (!(old_termios->c_cflag & CBAUD) && (cflag & CBAUD)) {
                unsigned int mask = TIOCM_DTR;
                if (!(cflag & CRTSCTS) ||
                    !test_bit(TTY_THROTTLED, &tty->flags))
                        mask |= TIOCM_RTS;
                uart_set_mctrl(state->uart_port, mask);
        }

        /* Handle turning off CRTSCTS */
        if ((old_termios->c_cflag & CRTSCTS) && !(cflag & CRTSCTS)) {
                spin_lock_irqsave(&state->uart_port->lock, flags);
                tty->hw_stopped = 0;
                __uart_start(tty);
                spin_unlock_irqrestore(&state->uart_port->lock, flags);
        }

        /* Handle turning on CRTSCTS */
        if (!(old_termios->c_cflag & CRTSCTS) && (cflag & CRTSCTS)) {
                spin_lock_irqsave(&state->uart_port->lock, flags);
                if (!(state->uart_port->ops->get_mctrl(state->uart_port) & TIOCM_CTS)) {
                        tty->hw_stopped = 1;
                        state->uart_port->ops->stop_tx(state->uart_port);
                }
                spin_unlock_irqrestore(&state->uart_port->lock, flags);
        }
#if 0
        /*
         * No need to wake up processes in open wait, since they
         * sample the CLOCAL flag once, and don't recheck it.
         * XXX  It's not clear whether the current behavior is correct
         * or not.  Hence, this may change.....
         */
        if (!(old_termios->c_cflag & CLOCAL) &&
            (tty->termios->c_cflag & CLOCAL))
                wake_up_interruptible(&state->uart_port.open_wait);
#endif
}

/*
 * In 2.4.5, calls to this will be serialized via the BKL in
 *  linux/drivers/char/tty_io.c:tty_release()
 *  linux/drivers/char/tty_io.c:do_tty_handup()
 */
static void uart_close(struct tty_struct *tty, struct file *filp)
{
        struct uart_state *state = tty->driver_data;
        struct tty_port *port;
        struct uart_port *uport;

        BUG_ON(!kernel_locked());

        if (!state)
                return;

        uport = state->uart_port;
        port = &state->port;

        pr_debug("uart_close(%d) called\n", uport->line);

        mutex_lock(&port->mutex);

        if (tty_hung_up_p(filp))
                goto done;

        if ((tty->count == 1) && (port->count != 1)) {
                /*
                 * Uh, oh.  tty->count is 1, which means that the tty
                 * structure will be freed.  port->count should always
                 * be one in these conditions.  If it's greater than
                 * one, we've got real problems, since it means the
                 * serial port won't be shutdown.
                 */
                printk(KERN_ERR "uart_close: bad serial port count; tty->count is 1, "
                       "port->count is %d\n", port->count);
                port->count = 1;
        }
        if (--port->count < 0) {
                printk(KERN_ERR "uart_close: bad serial port count for %s: %d\n",
                       tty->name, port->count);
                port->count = 0;
        }
        if (port->count)
                goto done;

        /*
         * Now we wait for the transmit buffer to clear; and we notify
         * the line discipline to only process XON/XOFF characters by
         * setting tty->closing.
         */
        tty->closing = 1;

        if (port->closing_wait != ASYNC_CLOSING_WAIT_NONE)
                tty_wait_until_sent(tty, msecs_to_jiffies(port->closing_wait));

        /*
         * At this point, we stop accepting input.  To do this, we
         * disable the receive line status interrupts.
         */
        if (port->flags & ASYNC_INITIALIZED) {
                unsigned long flags;
                spin_lock_irqsave(&uport->lock, flags);
                uport->ops->stop_rx(uport);
                spin_unlock_irqrestore(&uport->lock, flags);
                /*
                 * Before we drop DTR, make sure the UART transmitter
                 * has completely drained; this is especially
                 * important if there is a transmit FIFO!
                 */
                uart_wait_until_sent(tty, uport->timeout);
        }

        uart_shutdown(state);
        uart_flush_buffer(tty);

        tty_ldisc_flush(tty);

        tty->closing = 0;
        tty_port_tty_set(port, NULL);

        if (port->blocked_open) {
                if (port->close_delay)
                        msleep_interruptible(port->close_delay);
        } else if (!uart_console(uport)) {
                uart_change_pm(state, 3);
        }

        /*
         * Wake up anyone trying to open this port.
         */
        clear_bit(ASYNCB_NORMAL_ACTIVE, &port->flags);
        wake_up_interruptible(&port->open_wait);

done:
        mutex_unlock(&port->mutex);
}

static void uart_wait_until_sent(struct tty_struct *tty, int timeout)
{
        struct uart_state *state = tty->driver_data;
        struct uart_port *port = state->uart_port;
        unsigned long char_time, expire;

        if (port->type == PORT_UNKNOWN || port->fifosize == 0)
                return;

        lock_kernel();

        /*
         * Set the check interval to be 1/5 of the estimated time to
         * send a single character, and make it at least 1.  The check
         * interval should also be less than the timeout.
         *
         * Note: we have to use pretty tight timings here to satisfy
         * the NIST-PCTS.
         */
        char_time = (port->timeout - HZ/50) / port->fifosize;
        char_time = char_time / 5;
        if (char_time == 0)
                char_time = 1;
        if (timeout && timeout < char_time)
                char_time = timeout;

        /*
         * If the transmitter hasn't cleared in twice the approximate
         * amount of time to send the entire FIFO, it probably won't
         * ever clear.  This assumes the UART isn't doing flow
         * control, which is currently the case.  Hence, if it ever
         * takes longer than port->timeout, this is probably due to a
         * UART bug of some kind.  So, we clamp the timeout parameter at
         * 2*port->timeout.
         */
        if (timeout == 0 || timeout > 2 * port->timeout)
                timeout = 2 * port->timeout;

        expire = jiffies + timeout;

        pr_debug("uart_wait_until_sent(%d), jiffies=%lu, expire=%lu...\n",
                port->line, jiffies, expire);

        /*
         * Check whether the transmitter is empty every 'char_time'.
         * 'timeout' / 'expire' give us the maximum amount of time
         * we wait.
         */
        while (!port->ops->tx_empty(port)) {
                msleep_interruptible(jiffies_to_msecs(char_time));
                if (signal_pending(current))
                        break;
                if (time_after(jiffies, expire))
                        break;
        }
        set_current_state(TASK_RUNNING); /* might not be needed */
        unlock_kernel();
}

/*
 * This is called with the BKL held in
 *  linux/drivers/char/tty_io.c:do_tty_hangup()
 * We're called from the eventd thread, so we can sleep for
 * a _short_ time only.
 */
static void uart_hangup(struct tty_struct *tty)
{
        struct uart_state *state = tty->driver_data;
        struct tty_port *port = &state->port;

        BUG_ON(!kernel_locked());
        pr_debug("uart_hangup(%d)\n", state->uart_port->line);

        mutex_lock(&port->mutex);
        if (port->flags & ASYNC_NORMAL_ACTIVE) {
                uart_flush_buffer(tty);
                uart_shutdown(state);
                port->count = 0;
                clear_bit(ASYNCB_NORMAL_ACTIVE, &port->flags);
                tty_port_tty_set(port, NULL);
                wake_up_interruptible(&port->open_wait);
                wake_up_interruptible(&port->delta_msr_wait);
        }
        mutex_unlock(&port->mutex);
}

/*
 * Copy across the serial console cflag setting into the termios settings
 * for the initial open of the port.  This allows continuity between the
 * kernel settings, and the settings init adopts when it opens the port
 * for the first time.
 */
static void uart_update_termios(struct uart_state *state)
{
        struct tty_struct *tty = state->port.tty;
        struct uart_port *port = state->uart_port;

        if (uart_console(port) && port->cons->cflag) {
                tty->termios->c_cflag = port->cons->cflag;
                port->cons->cflag = 0;
        }

        /*
         * If the device failed to grab its irq resources,
         * or some other error occurred, don't try to talk
         * to the port hardware.
         */
        if (!(tty->flags & (1 << TTY_IO_ERROR))) {
                /*
                 * Make termios settings take effect.
                 */
                uart_change_speed(state, NULL);

                /*
                 * And finally enable the RTS and DTR signals.
                 */
                if (tty->termios->c_cflag & CBAUD)
                        uart_set_mctrl(port, TIOCM_DTR | TIOCM_RTS);
        }
}

/*
 * Block the open until the port is ready.  We must be called with
 * the per-port semaphore held.
 */
static int
uart_block_til_ready(struct file *filp, struct uart_state *state)
{
        DECLARE_WAITQUEUE(wait, current);
        struct uart_port *uport = state->uart_port;
        struct tty_port *port = &state->port;
        unsigned int mctrl;

        port->blocked_open++;
        port->count--;

        add_wait_queue(&port->open_wait, &wait);
        while (1) {
                set_current_state(TASK_INTERRUPTIBLE);

                /*
                 * If we have been hung up, tell userspace/restart open.
                 */
                if (tty_hung_up_p(filp) || port->tty == NULL)
                        break;

                /*
                 * If the port has been closed, tell userspace/restart open.
                 */
                if (!(port->flags & ASYNC_INITIALIZED))
                        break;

                /*
                 * If non-blocking mode is set, or CLOCAL mode is set,
                 * we don't want to wait for the modem status lines to
                 * indicate that the port is ready.
                 *
                 * Also, if the port is not enabled/configured, we want
                 * to allow the open to succeed here.  Note that we will
                 * have set TTY_IO_ERROR for a non-existant port.
                 */
                if ((filp->f_flags & O_NONBLOCK) ||
                    (port->tty->termios->c_cflag & CLOCAL) ||
                    (port->tty->flags & (1 << TTY_IO_ERROR)))
                        break;

                /*
                 * Set DTR to allow modem to know we're waiting.  Do
                 * not set RTS here - we want to make sure we catch
                 * the data from the modem.
                 */
                if (port->tty->termios->c_cflag & CBAUD)
                        uart_set_mctrl(uport, TIOCM_DTR);

                /*
                 * and wait for the carrier to indicate that the
                 * modem is ready for us.
                 */
                spin_lock_irq(&uport->lock);
                uport->ops->enable_ms(uport);
                mctrl = uport->ops->get_mctrl(uport);
                spin_unlock_irq(&uport->lock);
                if (mctrl & TIOCM_CAR)
                        break;

                mutex_unlock(&port->mutex);
                schedule();
                mutex_lock(&port->mutex);

                if (signal_pending(current))
                        break;
        }
        set_current_state(TASK_RUNNING);
        remove_wait_queue(&port->open_wait, &wait);

        port->count++;
        port->blocked_open--;

        if (signal_pending(current))
                return -ERESTARTSYS;

        if (!port->tty || tty_hung_up_p(filp))
                return -EAGAIN;

        return 0;
}

static struct uart_state *uart_get(struct uart_driver *drv, int line)
{
        struct uart_state *state;
        struct tty_port *port;
        int ret = 0;

        state = drv->state + line;
        port = &state->port;
        if (mutex_lock_interruptible(&port->mutex)) {
                ret = -ERESTARTSYS;
                goto err;
        }

        port->count++;
        if (!state->uart_port || state->uart_port->flags & UPF_DEAD) {
                ret = -ENXIO;
                goto err_unlock;
        }
        return state;

 err_unlock:
        port->count--;
        mutex_unlock(&port->mutex);
 err:
        return ERR_PTR(ret);
}

/*
 * calls to uart_open are serialised by the BKL in
 *   fs/char_dev.c:chrdev_open()
 * Note that if this fails, then uart_close() _will_ be called.
 *
 * In time, we want to scrap the "opening nonpresent ports"
 * behaviour and implement an alternative way for setserial
 * to set base addresses/ports/types.  This will allow us to
 * get rid of a certain amount of extra tests.
 */
static int uart_open(struct tty_struct *tty, struct file *filp)
{
        struct uart_driver *drv = (struct uart_driver *)tty->driver->driver_state;
        struct uart_state *state;
        struct tty_port *port;
        int retval, line = tty->index;

        BUG_ON(!kernel_locked());
        pr_debug("uart_open(%d) called\n", line);

        /*
         * tty->driver->num won't change, so we won't fail here with
         * tty->driver_data set to something non-NULL (and therefore
         * we won't get caught by uart_close()).
         */
        retval = -ENODEV;
        if (line >= tty->driver->num)
                goto fail;

        /*
         * We take the semaphore inside uart_get to guarantee that we won't
         * be re-entered while allocating the state structure, or while we
         * request any IRQs that the driver may need.  This also has the nice
         * side-effect that it delays the action of uart_hangup, so we can
         * guarantee that state->port.tty will always contain something
         * reasonable.
         */
        state = uart_get(drv, line);
        if (IS_ERR(state)) {
                retval = PTR_ERR(state);
                goto fail;
        }
        port = &state->port;

        /*
         * Once we set tty->driver_data here, we are guaranteed that
         * uart_close() will decrement the driver module use count.
         * Any failures from here onwards should not touch the count.
         */
        tty->driver_data = state;
        state->uart_port->state = state;
        tty->low_latency = (state->uart_port->flags & UPF_LOW_LATENCY) ? 1 : 0;
        tty->alt_speed = 0;
        tty_port_tty_set(port, tty);

        /*
         * If the port is in the middle of closing, bail out now.
         */
        if (tty_hung_up_p(filp)) {
                retval = -EAGAIN;
                port->count--;
                mutex_unlock(&port->mutex);
                goto fail;
        }

        /*
         * Make sure the device is in D0 state.
         */
        if (port->count == 1)
                uart_change_pm(state, 0);

        /*
         * Start up the serial port.
         */
        retval = uart_startup(state, 0);

        /*
         * If we succeeded, wait until the port is ready.
         */
        if (retval == 0)
                retval = uart_block_til_ready(filp, state);
        mutex_unlock(&port->mutex);

        /*
         * If this is the first open to succeed, adjust things to suit.
         */
        if (retval == 0 && !(port->flags & ASYNC_NORMAL_ACTIVE)) {
                set_bit(ASYNCB_NORMAL_ACTIVE, &port->flags);

                uart_update_termios(state);
        }

fail:
        return retval;
}

static const char *uart_type(struct uart_port *port)
{
        const char *str = NULL;

        if (port->ops->type)
                str = port->ops->type(port);

        if (!str)
                str = "unknown";

        return str;
}

#ifdef CONFIG_PROC_FS

static void uart_line_info(struct seq_file *m, struct uart_driver *drv, int i)
{
        struct uart_state *state = drv->state + i;
        struct tty_port *port = &state->port;
        int pm_state;
        struct uart_port *uport = state->uart_port;
        char stat_buf[32];
        unsigned int status;
        int mmio;

        if (!uport)
                return;

        mmio = uport->iotype >= UPIO_MEM;
        seq_printf(m, "%d: uart:%s %s%08llX irq:%d",
                        uport->line, uart_type(uport),
                        mmio ? "mmio:0x" : "port:",
                        mmio ? (unsigned long long)uport->mapbase
                             : (unsigned long long)uport->iobase,
                        uport->irq);

        if (uport->type == PORT_UNKNOWN) {
                seq_putc(m, '\n');
                return;
        }

        if (capable(CAP_SYS_ADMIN)) {
                mutex_lock(&port->mutex);
                pm_state = state->pm_state;
                if (pm_state)
                        uart_change_pm(state, 0);
                spin_lock_irq(&uport->lock);
                status = uport->ops->get_mctrl(uport);
                spin_unlock_irq(&uport->lock);
                if (pm_state)
                        uart_change_pm(state, pm_state);
                mutex_unlock(&port->mutex);

                seq_printf(m, " tx:%d rx:%d",
                                uport->icount.tx, uport->icount.rx);
                if (uport->icount.frame)
                        seq_printf(m, " fe:%d",
                                uport->icount.frame);
                if (uport->icount.parity)
                        seq_printf(m, " pe:%d",
                                uport->icount.parity);
                if (uport->icount.brk)
                        seq_printf(m, " brk:%d",
                                uport->icount.brk);
                if (uport->icount.overrun)
                        seq_printf(m, " oe:%d",
                                uport->icount.overrun);

#define INFOBIT(bit, str) \
        if (uport->mctrl & (bit)) \
                strncat(stat_buf, (str), sizeof(stat_buf) - \
                        strlen(stat_buf) - 2)
#define STATBIT(bit, str) \
        if (status & (bit)) \
                strncat(stat_buf, (str), sizeof(stat_buf) - \
                       strlen(stat_buf) - 2)

                stat_buf[0] = '\0';
                stat_buf[1] = '\0';
                INFOBIT(TIOCM_RTS, "|RTS");
                STATBIT(TIOCM_CTS, "|CTS");
                INFOBIT(TIOCM_DTR, "|DTR");
                STATBIT(TIOCM_DSR, "|DSR");
                STATBIT(TIOCM_CAR, "|CD");
                STATBIT(TIOCM_RNG, "|RI");
                if (stat_buf[0])
                        stat_buf[0] = ' ';

                seq_puts(m, stat_buf);
        }
        seq_putc(m, '\n');
#undef STATBIT
#undef INFOBIT
}

static int uart_proc_show(struct seq_file *m, void *v)
{
        struct tty_driver *ttydrv = m->private;
        struct uart_driver *drv = ttydrv->driver_state;
        int i;

        seq_printf(m, "serinfo:1.0 driver%s%s revision:%s\n",
                        "", "", "");
        for (i = 0; i < drv->nr; i++)
                uart_line_info(m, drv, i);
        return 0;
}

static int uart_proc_open(struct inode *inode, struct file *file)
{
        return single_open(file, uart_proc_show, PDE(inode)->data);
}

static const struct file_operations uart_proc_fops = {
        .owner          = THIS_MODULE,
        .open           = uart_proc_open,
        .read           = seq_read,
        .llseek         = seq_lseek,
        .release        = single_release,
};
#endif

#if defined(CONFIG_SERIAL_CORE_CONSOLE) || defined(CONFIG_CONSOLE_POLL)
/*
 *      uart_console_write - write a console message to a serial port
 *      @port: the port to write the message
 *      @s: array of characters
 *      @count: number of characters in string to write
 *      @write: function to write character to port
 */
void uart_console_write(struct uart_port *port, const char *s,
                        unsigned int count,
                        void (*putchar)(struct uart_port *, int))
{
        unsigned int i;

        for (i = 0; i < count; i++, s++) {
                if (*s == '\n')
                        putchar(port, '\r');
                putchar(port, *s);
        }
}
EXPORT_SYMBOL_GPL(uart_console_write);

/*
 *      Check whether an invalid uart number has been specified, and
 *      if so, search for the first available port that does have
 *      console support.
 */
struct uart_port * __init
uart_get_console(struct uart_port *ports, int nr, struct console *co)
{
        int idx = co->index;

        if (idx < 0 || idx >= nr || (ports[idx].iobase == 0 &&
                                     ports[idx].membase == NULL))
                for (idx = 0; idx < nr; idx++)
                        if (ports[idx].iobase != 0 ||
                            ports[idx].membase != NULL)
                                break;

        co->index = idx;

        return ports + idx;
}

/**
 *      uart_parse_options - Parse serial port baud/parity/bits/flow contro.
 *      @options: pointer to option string
 *      @baud: pointer to an 'int' variable for the baud rate.
 *      @parity: pointer to an 'int' variable for the parity.
 *      @bits: pointer to an 'int' variable for the number of data bits.
 *      @flow: pointer to an 'int' variable for the flow control character.
 *
 *      uart_parse_options decodes a string containing the serial console
 *      options.  The format of the string is <baud><parity><bits><flow>,
 *      eg: 115200n8r
 */
void
uart_parse_options(char *options, int *baud, int *parity, int *bits, int *flow)
{
        char *s = options;

        *baud = simple_strtoul(s, NULL, 10);
        while (*s >= '0' && *s <= '9')
                s++;
        if (*s)
                *parity = *s++;
        if (*s)
                *bits = *s++ - '0';
        if (*s)
                *flow = *s;
}
EXPORT_SYMBOL_GPL(uart_parse_options);

struct baud_rates {
        unsigned int rate;
        unsigned int cflag;
};

static const struct baud_rates baud_rates[] = {
        { 921600, B921600 },
        { 460800, B460800 },
        { 230400, B230400 },
        { 115200, B115200 },
        {  57600, B57600  },
        {  38400, B38400  },
        {  19200, B19200  },
        {   9600, B9600   },
        {   4800, B4800   },
        {   2400, B2400   },
        {   1200, B1200   },
        {      0, B38400  }
};

/**
 *      uart_set_options - setup the serial console parameters
 *      @port: pointer to the serial ports uart_port structure
 *      @co: console pointer
 *      @baud: baud rate
 *      @parity: parity character - 'n' (none), 'o' (odd), 'e' (even)
 *      @bits: number of data bits
 *      @flow: flow control character - 'r' (rts)
 */
int
uart_set_options(struct uart_port *port, struct console *co,
                 int baud, int parity, int bits, int flow)
{
        struct ktermios termios;
        static struct ktermios dummy;
        int i;

        /*
         * Ensure that the serial console lock is initialised
         * early.
         */
        spin_lock_init(&port->lock);
        lockdep_set_class(&port->lock, &port_lock_key);

        memset(&termios, 0, sizeof(struct ktermios));

        termios.c_cflag = CREAD | HUPCL | CLOCAL;

        /*
         * Construct a cflag setting.
         */
        for (i = 0; baud_rates[i].rate; i++)
                if (baud_rates[i].rate <= baud)
                        break;

        termios.c_cflag |= baud_rates[i].cflag;

        if (bits == 7)
                termios.c_cflag |= CS7;
        else
                termios.c_cflag |= CS8;

        switch (parity) {
        case 'o': case 'O':
                termios.c_cflag |= PARODD;
                /*fall through*/
        case 'e': case 'E':
                termios.c_cflag |= PARENB;
                break;
        }

        if (flow == 'r')
                termios.c_cflag |= CRTSCTS;

        /*
         * some uarts on other side don't support no flow control.
         * So we set * DTR in host uart to make them happy
         */
        port->mctrl |= TIOCM_DTR;

        port->ops->set_termios(port, &termios, &dummy);
        /*
         * Allow the setting of the UART parameters with a NULL console
         * too:
         */
        if (co)
                co->cflag = termios.c_cflag;

        return 0;
}
EXPORT_SYMBOL_GPL(uart_set_options);
#endif /* CONFIG_SERIAL_CORE_CONSOLE */

static void uart_change_pm(struct uart_state *state, int pm_state)
{
        struct uart_port *port = state->uart_port;

        if (state->pm_state != pm_state) {
                if (port->ops->pm)
                        port->ops->pm(port, pm_state, state->pm_state);
                state->pm_state = pm_state;
        }
}

struct uart_match {
        struct uart_port *port;
        struct uart_driver *driver;
};

static int serial_match_port(struct device *dev, void *data)
{
        struct uart_match *match = data;
        struct tty_driver *tty_drv = match->driver->tty_driver;
        dev_t devt = MKDEV(tty_drv->major, tty_drv->minor_start) +
                match->port->line;

        return dev->devt == devt; /* Actually, only one tty per port */
}

int uart_suspend_port(struct uart_driver *drv, struct uart_port *uport)
{
        struct uart_state *state = drv->state + uport->line;
        struct tty_port *port = &state->port;
        struct device *tty_dev;
        struct uart_match match = {uport, drv};

        mutex_lock(&port->mutex);

        if (!console_suspend_enabled && uart_console(uport)) {
                /* we're going to avoid suspending serial console */
                mutex_unlock(&port->mutex);
                return 0;
        }

        tty_dev = device_find_child(uport->dev, &match, serial_match_port);
        if (device_may_wakeup(tty_dev)) {
                enable_irq_wake(uport->irq);
                put_device(tty_dev);
                mutex_unlock(&port->mutex);
                return 0;
        }
        uport->suspended = 1;

        if (port->flags & ASYNC_INITIALIZED) {
                const struct uart_ops *ops = uport->ops;
                int tries;

                set_bit(ASYNCB_SUSPENDED, &port->flags);
                clear_bit(ASYNCB_INITIALIZED, &port->flags);

                spin_lock_irq(&uport->lock);
                ops->stop_tx(uport);
                ops->set_mctrl(uport, 0);
                ops->stop_rx(uport);
                spin_unlock_irq(&uport->lock);

                /*
                 * Wait for the transmitter to empty.
                 */
                for (tries = 3; !ops->tx_empty(uport) && tries; tries--)
                        msleep(10);
                if (!tries)
                        printk(KERN_ERR "%s%s%s%d: Unable to drain "
                                        "transmitter\n",
                               uport->dev ? dev_name(uport->dev) : "",
                               uport->dev ? ": " : "",
                               drv->dev_name,
                               drv->tty_driver->name_base + uport->line);

                ops->shutdown(uport);
        }

        /*
         * Disable the console device before suspending.
         */
        if (uart_console(uport))
                console_stop(uport->cons);

        uart_change_pm(state, 3);

        mutex_unlock(&port->mutex);

        return 0;
}

int uart_resume_port(struct uart_driver *drv, struct uart_port *uport)
{
        struct uart_state *state = drv->state + uport->line;
        struct tty_port *port = &state->port;
        struct device *tty_dev;
        struct uart_match match = {uport, drv};
        struct ktermios termios;

        mutex_lock(&port->mutex);

        if (!console_suspend_enabled && uart_console(uport)) {
                /* no need to resume serial console, it wasn't suspended */
                /*
                 * First try to use the console cflag setting.
                 */
                memset(&termios, 0, sizeof(struct ktermios));
                termios.c_cflag = uport->cons->cflag;
                /*
                 * If that's unset, use the tty termios setting.
                 */
                if (termios.c_cflag == 0)
                        termios = *state->port.tty->termios;
                else {
                        termios.c_ispeed = termios.c_ospeed =
                                tty_termios_input_baud_rate(&termios);
                        termios.c_ispeed = termios.c_ospeed =
                                tty_termios_baud_rate(&termios);
                }
                uport->ops->set_termios(uport, &termios, NULL);
                mutex_unlock(&port->mutex);
                return 0;
        }

        tty_dev = device_find_child(uport->dev, &match, serial_match_port);
        if (!uport->suspended && device_may_wakeup(tty_dev)) {
                disable_irq_wake(uport->irq);
                mutex_unlock(&port->mutex);
                return 0;
        }
        uport->suspended = 0;

        /*
         * Re-enable the console device after suspending.
         */
        if (uart_console(uport)) {
                uart_change_pm(state, 0);
                uport->ops->set_termios(uport, &termios, NULL);
                console_start(uport->cons);
        }

        if (port->flags & ASYNC_SUSPENDED) {
                const struct uart_ops *ops = uport->ops;
                int ret;

                uart_change_pm(state, 0);
                spin_lock_irq(&uport->lock);
                ops->set_mctrl(uport, 0);
                spin_unlock_irq(&uport->lock);
                ret = ops->startup(uport);
                if (ret == 0) {
                        uart_change_speed(state, NULL);
                        spin_lock_irq(&uport->lock);
                        ops->set_mctrl(uport, uport->mctrl);
                        ops->start_tx(uport);
                        spin_unlock_irq(&uport->lock);
                        set_bit(ASYNCB_INITIALIZED, &port->flags);
                } else {
                        /*
                         * Failed to resume - maybe hardware went away?
                         * Clear the "initialized" flag so we won't try
                         * to call the low level drivers shutdown method.
                         */
                        uart_shutdown(state);
                }

                clear_bit(ASYNCB_SUSPENDED, &port->flags);
        }

        mutex_unlock(&port->mutex);

        return 0;
}

static inline void
uart_report_port(struct uart_driver *drv, struct uart_port *port)
{
        char address[64];

        switch (port->iotype) {
        case UPIO_PORT:
                snprintf(address, sizeof(address), "I/O 0x%lx", port->iobase);
                break;
        case UPIO_HUB6:
                snprintf(address, sizeof(address),
                         "I/O 0x%lx offset 0x%x", port->iobase, port->hub6);
                break;
        case UPIO_MEM:
        case UPIO_MEM32:
        case UPIO_AU:
        case UPIO_TSI:
        case UPIO_DWAPB:
                snprintf(address, sizeof(address),
                         "MMIO 0x%llx", (unsigned long long)port->mapbase);
                break;
        default:
                strlcpy(address, "*unknown*", sizeof(address));
                break;
        }

        printk(KERN_INFO "%s%s%s%d at %s (irq = %d) is a %s\n",
               port->dev ? dev_name(port->dev) : "",
               port->dev ? ": " : "",
               drv->dev_name,
               drv->tty_driver->name_base + port->line,
               address, port->irq, uart_type(port));
}

static void
uart_configure_port(struct uart_driver *drv, struct uart_state *state,
                    struct uart_port *port)
{
        unsigned int flags;

        /*
         * If there isn't a port here, don't do anything further.
         */
        if (!port->iobase && !port->mapbase && !port->membase)
                return;

        /*
         * Now do the auto configuration stuff.  Note that config_port
         * is expected to claim the resources and map the port for us.
         */
        flags = 0;
        if (port->flags & UPF_AUTO_IRQ)
                flags |= UART_CONFIG_IRQ;
        if (port->flags & UPF_BOOT_AUTOCONF) {
                if (!(port->flags & UPF_FIXED_TYPE)) {
                        port->type = PORT_UNKNOWN;
                        flags |= UART_CONFIG_TYPE;
                }
                port->ops->config_port(port, flags);
        }

        if (port->type != PORT_UNKNOWN) {
                unsigned long flags;

                uart_report_port(drv, port);

                /* Power up port for set_mctrl() */
                uart_change_pm(state, 0);

                /*
                 * Ensure that the modem control lines are de-activated.
                 * keep the DTR setting that is set in uart_set_options()
                 * We probably don't need a spinlock around this, but
                 */
                spin_lock_irqsave(&port->lock, flags);
                port->ops->set_mctrl(port, port->mctrl & TIOCM_DTR);
                spin_unlock_irqrestore(&port->lock, flags);

                /*
                 * If this driver supports console, and it hasn't been
                 * successfully registered yet, try to re-register it.
                 * It may be that the port was not available.
                 */
                if (port->cons && !(port->cons->flags & CON_ENABLED))
                        register_console(port->cons);

                /*
                 * Power down all ports by default, except the
                 * console if we have one.
                 */
                if (!uart_console(port))
                        uart_change_pm(state, 3);
        }
}

#ifdef CONFIG_CONSOLE_POLL

static int uart_poll_init(struct tty_driver *driver, int line, char *options)
{
        struct uart_driver *drv = driver->driver_state;
        struct uart_state *state = drv->state + line;
        struct uart_port *port;
        int baud = 9600;
        int bits = 8;
        int parity = 'n';
        int flow = 'n';

        if (!state || !state->uart_port)
                return -1;

        port = state->uart_port;
        if (!(port->ops->poll_get_char && port->ops->poll_put_char))
                return -1;

        if (options) {
                uart_parse_options(options, &baud, &parity, &bits, &flow);
                return uart_set_options(port, NULL, baud, parity, bits, flow);
        }

        return 0;
}

static int uart_poll_get_char(struct tty_driver *driver, int line)
{
        struct uart_driver *drv = driver->driver_state;
        struct uart_state *state = drv->state + line;
        struct uart_port *port;

        if (!state || !state->uart_port)
                return -1;

        port = state->uart_port;
        return port->ops->poll_get_char(port);
}

static void uart_poll_put_char(struct tty_driver *driver, int line, char ch)
{
        struct uart_driver *drv = driver->driver_state;
        struct uart_state *state = drv->state + line;
        struct uart_port *port;

        if (!state || !state->uart_port)
                return;

        port = state->uart_port;
        port->ops->poll_put_char(port, ch);
}
#endif

static const struct tty_operations uart_ops = {
        .open           = uart_open,
        .close          = uart_close,
        .write          = uart_write,
        .put_char       = uart_put_char,
        .flush_chars    = uart_flush_chars,
        .write_room     = uart_write_room,
        .chars_in_buffer= uart_chars_in_buffer,
        .flush_buffer   = uart_flush_buffer,
        .ioctl          = uart_ioctl,
        .throttle       = uart_throttle,
        .unthrottle     = uart_unthrottle,
        .send_xchar     = uart_send_xchar,
        .set_termios    = uart_set_termios,
        .set_ldisc      = uart_set_ldisc,
        .stop           = uart_stop,
        .start          = uart_start,
        .hangup         = uart_hangup,
        .break_ctl      = uart_break_ctl,
        .wait_until_sent= uart_wait_until_sent,
#ifdef CONFIG_PROC_FS
        .proc_fops      = &uart_proc_fops,
#endif
        .tiocmget       = uart_tiocmget,
        .tiocmset       = uart_tiocmset,
#ifdef CONFIG_CONSOLE_POLL
        .poll_init      = uart_poll_init,
        .poll_get_char  = uart_poll_get_char,
        .poll_put_char  = uart_poll_put_char,
#endif
};

/**
 *      uart_register_driver - register a driver with the uart core layer
 *      @drv: low level driver structure
 *
 *      Register a uart driver with the core driver.  We in turn register
 *      with the tty layer, and initialise the core driver per-port state.
 *
 *      We have a proc file in /proc/tty/driver which is named after the
 *      normal driver.
 *
 *      drv->port should be NULL, and the per-port structures should be
 *      registered using uart_add_one_port after this call has succeeded.
 */
int uart_register_driver(struct uart_driver *drv)
{
        struct tty_driver *normal = NULL;
        int i, retval;

        BUG_ON(drv->state);

        /*
         * Maybe we should be using a slab cache for this, especially if
         * we have a large number of ports to handle.
         */
        drv->state = kzalloc(sizeof(struct uart_state) * drv->nr, GFP_KERNEL);
        retval = -ENOMEM;
        if (!drv->state)
                goto out;

        normal  = alloc_tty_driver(drv->nr);
        if (!normal)
                goto out;

        drv->tty_driver = normal;

        normal->owner           = drv->owner;
        normal->driver_name     = drv->driver_name;
        normal->name            = drv->dev_name;
        normal->major           = drv->major;
        normal->minor_start     = drv->minor;
        normal->type            = TTY_DRIVER_TYPE_SERIAL;
        normal->subtype         = SERIAL_TYPE_NORMAL;
        normal->init_termios    = tty_std_termios;
        normal->init_termios.c_cflag = B9600 | CS8 | CREAD | HUPCL | CLOCAL;
        normal->init_termios.c_ispeed = normal->init_termios.c_ospeed = 9600;
        normal->flags           = TTY_DRIVER_REAL_RAW | TTY_DRIVER_DYNAMIC_DEV;
        normal->driver_state    = drv;
        tty_set_operations(normal, &uart_ops);

        /*
         * Initialise the UART state(s).
         */
        for (i = 0; i < drv->nr; i++) {
                struct uart_state *state = drv->state + i;
                struct tty_port *port = &state->port;

                tty_port_init(port);
                port->close_delay     = 500;    /* .5 seconds */
                port->closing_wait    = 30000;  /* 30 seconds */
                tasklet_init(&state->tlet, uart_tasklet_action,
                             (unsigned long)state);
        }

        retval = tty_register_driver(normal);
 out:
        if (retval < 0) {
                put_tty_driver(normal);
                kfree(drv->state);
        }
        return retval;
}

/**
 *      uart_unregister_driver - remove a driver from the uart core layer
 *      @drv: low level driver structure
 *
 *      Remove all references to a driver from the core driver.  The low
 *      level driver must have removed all its ports via the
 *      uart_remove_one_port() if it registered them with uart_add_one_port().
 *      (ie, drv->port == NULL)
 */
void uart_unregister_driver(struct uart_driver *drv)
{
        struct tty_driver *p = drv->tty_driver;
        tty_unregister_driver(p);
        put_tty_driver(p);
        kfree(drv->state);
        drv->tty_driver = NULL;
}

struct tty_driver *uart_console_device(struct console *co, int *index)
{
        struct uart_driver *p = co->data;
        *index = co->index;
        return p->tty_driver;
}

/**
 *      uart_add_one_port - attach a driver-defined port structure
 *      @drv: pointer to the uart low level driver structure for this port
 *      @uport: uart port structure to use for this port.
 *
 *      This allows the driver to register its own uart_port structure
 *      with the core driver.  The main purpose is to allow the low
 *      level uart drivers to expand uart_port, rather than having yet
 *      more levels of structures.
 */
int uart_add_one_port(struct uart_driver *drv, struct uart_port *uport)
{
        struct uart_state *state;
        struct tty_port *port;
        int ret = 0;
        struct device *tty_dev;

        BUG_ON(in_interrupt());

        if (uport->line >= drv->nr)
                return -EINVAL;

        state = drv->state + uport->line;
        port = &state->port;

        mutex_lock(&port_mutex);
        mutex_lock(&port->mutex);
        if (state->uart_port) {
                ret = -EINVAL;
                goto out;
        }

        state->uart_port = uport;
        state->pm_state = -1;

        uport->cons = drv->cons;
        uport->state = state;

        /*
         * If this port is a console, then the spinlock is already
         * initialised.
         */
        if (!(uart_console(uport) && (uport->cons->flags & CON_ENABLED))) {
                spin_lock_init(&uport->lock);
                lockdep_set_class(&uport->lock, &port_lock_key);
        }

        uart_configure_port(drv, state, uport);

        /*
         * Register the port whether it's detected or not.  This allows
         * setserial to be used to alter this ports parameters.
         */
        tty_dev = tty_register_device(drv->tty_driver, uport->line, uport->dev);
        if (likely(!IS_ERR(tty_dev))) {
                device_init_wakeup(tty_dev, 1);
                device_set_wakeup_enable(tty_dev, 0);
        } else
                printk(KERN_ERR "Cannot register tty device on line %d\n",
                       uport->line);

        /*
         * Ensure UPF_DEAD is not set.
         */
        uport->flags &= ~UPF_DEAD;

 out:
        mutex_unlock(&port->mutex);
        mutex_unlock(&port_mutex);

        return ret;
}

/**
 *      uart_remove_one_port - detach a driver defined port structure
 *      @drv: pointer to the uart low level driver structure for this port
 *      @uport: uart port structure for this port
 *
 *      This unhooks (and hangs up) the specified port structure from the
 *      core driver.  No further calls will be made to the low-level code
 *      for this port.
 */
int uart_remove_one_port(struct uart_driver *drv, struct uart_port *uport)
{
        struct uart_state *state = drv->state + uport->line;
        struct tty_port *port = &state->port;

        BUG_ON(in_interrupt());

        if (state->uart_port != uport)
                printk(KERN_ALERT "Removing wrong port: %p != %p\n",
                        state->uart_port, uport);

        mutex_lock(&port_mutex);

        /*
         * Mark the port "dead" - this prevents any opens from
         * succeeding while we shut down the port.
         */
        mutex_lock(&port->mutex);
        uport->flags |= UPF_DEAD;
        mutex_unlock(&port->mutex);

        /*
         * Remove the devices from the tty layer
         */
        tty_unregister_device(drv->tty_driver, uport->line);

        if (port->tty)
                tty_vhangup(port->tty);

        /*
         * Free the port IO and memory resources, if any.
         */
        if (uport->type != PORT_UNKNOWN)
                uport->ops->release_port(uport);

        /*
         * Indicate that there isn't a port here anymore.
         */
        uport->type = PORT_UNKNOWN;

        /*
         * Kill the tasklet, and free resources.
         */
        tasklet_kill(&state->tlet);

        state->uart_port = NULL;
        mutex_unlock(&port_mutex);

        return 0;
}

/*
 *      Are the two ports equivalent?
 */
int uart_match_port(struct uart_port *port1, struct uart_port *port2)
{
        if (port1->iotype != port2->iotype)
                return 0;

        switch (port1->iotype) {
        case UPIO_PORT:
                return (port1->iobase == port2->iobase);
        case UPIO_HUB6:
                return (port1->iobase == port2->iobase) &&
                       (port1->hub6   == port2->hub6);
        case UPIO_MEM:
        case UPIO_MEM32:
        case UPIO_AU:
        case UPIO_TSI:
        case UPIO_DWAPB:
                return (port1->mapbase == port2->mapbase);
        }
        return 0;
}
EXPORT_SYMBOL(uart_match_port);

EXPORT_SYMBOL(uart_write_wakeup);
EXPORT_SYMBOL(uart_register_driver);
EXPORT_SYMBOL(uart_unregister_driver);
EXPORT_SYMBOL(uart_suspend_port);
EXPORT_SYMBOL(uart_resume_port);
EXPORT_SYMBOL(uart_add_one_port);
EXPORT_SYMBOL(uart_remove_one_port);

MODULE_DESCRIPTION("Serial driver core");
MODULE_LICENSE("GPL");