Documentation/devicetree/bindings/pci/amlogic,meson-pcie.txt

   1 Amlogic Meson AXG DWC PCIE SoC controller
   2
   3 Amlogic Meson PCIe host controller is based on the Synopsys DesignWare PCI core.
   4 It shares common functions with the PCIe DesignWare core driver and
   5 inherits common properties defined in
   6 Documentation/devicetree/bindings/pci/designware-pcie.txt.
   7
   8 Additional properties are described here:
   9
  10 Required properties:
  11 - compatible:
  12         should contain :
  13         - "amlogic,axg-pcie" for AXG SoC Family
  14         - "amlogic,g12a-pcie" for G12A SoC Family
  15         to identify the core.
  16 - reg:
  17         should contain the configuration address space.
  18 - reg-names: Must be
  19         - "elbi"        External local bus interface registers
  20         - "cfg"         Meson specific registers
  21         - "config"      PCIe configuration space
  22 - reset-gpios: The GPIO to generate PCIe PERST# assert and deassert signal.
  23 - clocks: Must contain an entry for each entry in clock-names.
  24 - clock-names: Must include the following entries:
  25         - "pclk"       PCIe GEN 100M PLL clock
  26         - "port"       PCIe_x(A or B) RC clock gate
  27         - "general"    PCIe Phy clock
  28 - resets: phandle to the reset lines.
  29 - reset-names: must contain "port" and "apb"
  30        - "port"        Port A or B reset
  31        - "apb"         Share APB reset
  32 - phys: should contain a phandle to the PCIE phy
  33 - phy-names: must contain "pcie"
  34
  35 - device_type:
  36         should be "pci". As specified in designware-pcie.txt
  37
  38
  39 Example configuration:
  40
  41         pcie: pcie@f9800000 {
  42                         compatible = "amlogic,axg-pcie", "snps,dw-pcie";
  43                         reg = <0x0 0xf9800000 0x0 0x400000
  44                                         0x0 0xff646000 0x0 0x2000
  45                                         0x0 0xf9f00000 0x0 0x100000>;
  46                         reg-names = "elbi", "cfg", "config";
  47                         reset-gpios = <&gpio GPIOX_19 GPIO_ACTIVE_HIGH>;
  48                         interrupts = <GIC_SPI 177 IRQ_TYPE_EDGE_RISING>;
  49                         #interrupt-cells = <1>;
  50                         interrupt-map-mask = <0 0 0 0>;
  51                         interrupt-map = <0 0 0 0 &gic GIC_SPI 179 IRQ_TYPE_EDGE_RISING>;
  52                         bus-range = <0x0 0xff>;
  53                         #address-cells = <3>;
  54                         #size-cells = <2>;
  55                         device_type = "pci";
  56                         ranges = <0x82000000 0 0 0x0 0xf9c00000 0 0x00300000>;
  57
  58                         clocks = <&clkc CLKID_USB
  59                                         &clkc CLKID_PCIE_A
  60                                         &clkc CLKID_PCIE_CML_EN0>;
  61                         clock-names = "general",
  62                                         "pclk",
  63                                         "port";
  64                         resets = <&reset RESET_PCIE_A>,
  65                                 <&reset RESET_PCIE_APB>;
  66                         reset-names = "port",
  67                                         "apb";
  68                         phys = <&pcie_phy>;
  69                         phy-names = "pcie";
  70         };