WIP FPC-III support
[linux/fpc-iii.git] / arch / arm / boot / dts / logicpd-som-lv-baseboard.dtsi
blob7d0468a237818ceca1ef0ab9c842907815d937da
1 // SPDX-License-Identifier: GPL-2.0-only
3 / {
4         gpio_keys {
5                 compatible = "gpio-keys";
6                 pinctrl-names = "default";
7                 pinctrl-0 = <&gpio_key_pins>;
9                 sysboot2 {
10                         label = "gpio3";
11                         gpios = <&gpio4 15 GPIO_ACTIVE_LOW>;    /* gpio_111 / uP_GPIO_3 */
12                         linux,code = <BTN_0>;
13                         wakeup-source;
14                 };
15         };
17         sound {
18                 compatible = "ti,omap-twl4030";
19                 ti,model = "omap3logic";
20                 ti,mcbsp = <&mcbsp2>;
21         };
23         leds {
24                 compatible = "gpio-leds";
25                 pinctrl-names = "default";
26                 pinctrl-0 = <&led_pins &led_pins_wkup>;
28                 led1 {
29                         label = "led1";
30                         gpios = <&gpio5 5 GPIO_ACTIVE_LOW>;     /* gpio133 */
31                         linux,default-trigger = "cpu0";
32                 };
34                 led2 {
35                         label = "led2";
36                         gpios = <&gpio1 11 GPIO_ACTIVE_LOW>;    /* gpio11 */
37                         linux,default-trigger = "none";
38                 };
39         };
42 &vaux1 {
43         regulator-min-microvolt = <3000000>;
44         regulator-max-microvolt = <3000000>;
47 &vaux4 {
48         regulator-min-microvolt = <1800000>;
49         regulator-max-microvolt = <1800000>;
52 &mcbsp2 {
53         status = "okay";
54         pinctrl-names = "default";
55         pinctrl-0 = <&mcbsp2_pins>;
58 &charger {
59         ti,bb-uvolt = <3200000>;
60         ti,bb-uamp = <150>;
63 &gpmc {
64         ranges = <0 0 0x30000000 0x1000000      /* CS0: 16MB for NAND */
65                   1 0 0x2c000000 0x1000000      /* CS1: 16MB for LAN9221 */
66                   2 0 0x10000000 0x2000000>;    /* CS2: 32MB for NOR */
68         ethernet@gpmc {
69                 pinctrl-names = "default";
70                 pinctrl-0 = <&lan9221_pins>;
71                 interrupt-parent = <&gpio5>;
72                 interrupts = <24 IRQ_TYPE_LEVEL_LOW>;           /* gpio_152 */
73                 reg = <1 0 0xff>;
74         };
77 &vpll2 {
78         regulator-always-on;
81 &dss {
82         status = "okay";
83         vdds_dsi-supply = <&vpll2>;
84         vdda_video-supply = <&video_reg>;
85         pinctrl-names = "default";
86         pinctrl-0 = <&dss_dpi_pins1>;
87         port {
88                 dpi_out: endpoint {
89                         remote-endpoint = <&lcd_in>;
90                         data-lines = <16>;
91                 };
92         };
95 / {
96         aliases {
97                 display0 = &lcd0;
98         };
100         video_reg: video_reg {
101                 compatible = "regulator-fixed";
102                 regulator-name = "fixed-supply";
103                 regulator-min-microvolt = <3300000>;
104                 regulator-max-microvolt = <3300000>;
105         };
107         lcd0: display {
108                 /* This isn't the exact LCD, but the timings meet spec */
109                 compatible = "logicpd,type28";
110                 pinctrl-names = "default";
111                 pinctrl-0 = <&lcd_enable_pin>;
112                 backlight = <&bl>;
113                 enable-gpios = <&gpio5 27 GPIO_ACTIVE_HIGH>;
114                 port {
115                         lcd_in: endpoint {
116                                 remote-endpoint = <&dpi_out>;
117                         };
118                 };
119         };
121         bl: backlight {
122                 compatible = "pwm-backlight";
123                 pinctrl-names = "default";
124                 pinctrl-0 = <&backlight_pins>;
125                 pwms = <&twl_pwm 0 5000000>;
126                 brightness-levels = <0 10 20 30 40 50 60 70 80 90 100>;
127                 default-brightness-level = <7>;
128                 enable-gpios = <&gpio1 8 GPIO_ACTIVE_HIGH>; /* gpio_8 */
129         };
132 &mmc1 {
133         interrupts-extended = <&intc 83 &omap3_pmx_core 0x11a>;
134         pinctrl-names = "default";
135         pinctrl-0 = <&mmc1_pins>;
136         wp-gpios = <&gpio4 30 GPIO_ACTIVE_HIGH>;                /* gpio_126 */
137         cd-gpios = <&gpio4 14 GPIO_ACTIVE_LOW>;                 /* gpio_110 */
138         vmmc-supply = <&vmmc1>;
139         bus-width = <4>;
140         cap-power-off-card;
143 &omap3_pmx_core {
144         gpio_key_pins: pinmux_gpio_key_pins {
145                 pinctrl-single,pins = <
146                         OMAP3_CORE1_IOPAD(0x212e, PIN_INPUT_PULLUP | MUX_MODE4) /* cam_xclkb.gpio_111 / uP_GPIO_3*/
147                 >;
148         };
150         led_pins: pinmux_led_pins {
151                 pinctrl-single,pins = <
152                         OMAP3_CORE1_IOPAD(0x215e, PIN_OUTPUT_PULLUP | MUX_MODE4)        /* sdmmc2_dat1.gpio_133 / uP_GPIO_0 */
153                 >;
154         };
156         lan9221_pins: pinmux_lan9221_pins {
157                 pinctrl-single,pins = <
158                         OMAP3_CORE1_IOPAD(0x2184, PIN_INPUT_PULLUP | MUX_MODE4) /* mcbsp4_clkx.gpio_152 */
159                 >;
160         };
162         mmc1_pins: pinmux_mmc1_pins {
163                 pinctrl-single,pins = <
164                         OMAP3_CORE1_IOPAD(0x2144, PIN_OUTPUT | MUX_MODE0)       /* sdmmc1_clk.sdmmc1_clk */
165                         OMAP3_CORE1_IOPAD(0x2146, PIN_INPUT | MUX_MODE0)        /* sdmmc1_cmd.sdmmc1_cmd */
166                         OMAP3_CORE1_IOPAD(0x2148, PIN_INPUT | MUX_MODE0)        /* sdmmc1_dat0.sdmmc1_dat0 */
167                         OMAP3_CORE1_IOPAD(0x214a, PIN_INPUT | MUX_MODE0)        /* sdmmc1_dat1.sdmmc1_dat1 */
168                         OMAP3_CORE1_IOPAD(0x214c, PIN_INPUT | MUX_MODE0)        /* sdmmc1_dat2.sdmmc1_dat2 */
169                         OMAP3_CORE1_IOPAD(0x214e, PIN_INPUT | MUX_MODE0)        /* sdmmc1_dat3.sdmmc1_dat3 */
170                         OMAP3_CORE1_IOPAD(0x2132, PIN_INPUT_PULLUP | MUX_MODE4) /* cam_strobe.gpio_126 */
171                         OMAP3_CORE1_IOPAD(0x212c, PIN_INPUT_PULLUP | MUX_MODE4) /* cam_d11.gpio_110 */
172                 >;
173         };
175         lcd_enable_pin: pinmux_lcd_enable_pin {
176                 pinctrl-single,pins = <
177                         OMAP3_CORE1_IOPAD(0x218a, PIN_OUTPUT | PIN_OFF_OUTPUT_LOW | MUX_MODE4)       /* mcbsp4_fs.gpio_155 */
178                 >;
179         };
181         dss_dpi_pins1: pinmux_dss_dpi_pins1 {
182                 pinctrl-single,pins = <
183                         OMAP3_CORE1_IOPAD(0x20d4, PIN_OUTPUT_PULLDOWN | PIN_OFF_OUTPUT_LOW | MUX_MODE0)   /* dss_pclk.dss_pclk */
184                         OMAP3_CORE1_IOPAD(0x20d6, PIN_OUTPUT_PULLDOWN | PIN_OFF_OUTPUT_LOW | MUX_MODE0)   /* dss_hsync.dss_hsync */
185                         OMAP3_CORE1_IOPAD(0x20d8, PIN_OUTPUT_PULLDOWN | PIN_OFF_OUTPUT_LOW | MUX_MODE0)   /* dss_vsync.dss_vsync */
186                         OMAP3_CORE1_IOPAD(0x20da, PIN_OUTPUT_PULLDOWN | PIN_OFF_OUTPUT_LOW | MUX_MODE0)   /* dss_acbias.dss_acbias */
188                         OMAP3_CORE1_IOPAD(0x20dc, PIN_OUTPUT_PULLDOWN | PIN_OFF_OUTPUT_LOW | MUX_MODE0)   /* dss_data0.dss_data0 */
189                         OMAP3_CORE1_IOPAD(0x20de, PIN_OUTPUT_PULLDOWN | PIN_OFF_OUTPUT_LOW | MUX_MODE0)   /* dss_data1.dss_data1 */
190                         OMAP3_CORE1_IOPAD(0x20e0, PIN_OUTPUT_PULLDOWN | PIN_OFF_OUTPUT_LOW | MUX_MODE0)   /* dss_data2.dss_data2 */
191                         OMAP3_CORE1_IOPAD(0x20e2, PIN_OUTPUT_PULLDOWN | PIN_OFF_OUTPUT_LOW | MUX_MODE0)   /* dss_data3.dss_data3 */
192                         OMAP3_CORE1_IOPAD(0x20e4, PIN_OUTPUT_PULLDOWN | PIN_OFF_OUTPUT_LOW | MUX_MODE0)   /* dss_data4.dss_data4 */
193                         OMAP3_CORE1_IOPAD(0x20e6, PIN_OUTPUT_PULLDOWN | PIN_OFF_OUTPUT_LOW | MUX_MODE0)   /* dss_data5.dss_data5 */
194                         OMAP3_CORE1_IOPAD(0x20e8, PIN_OUTPUT_PULLDOWN | PIN_OFF_OUTPUT_LOW | MUX_MODE0)   /* dss_data6.dss_data6 */
195                         OMAP3_CORE1_IOPAD(0x20ea, PIN_OUTPUT_PULLDOWN | PIN_OFF_OUTPUT_LOW | MUX_MODE0)   /* dss_data7.dss_data7 */
196                         OMAP3_CORE1_IOPAD(0x20ec, PIN_OUTPUT_PULLDOWN | PIN_OFF_OUTPUT_LOW | MUX_MODE0)   /* dss_data8.dss_data8 */
197                         OMAP3_CORE1_IOPAD(0x20ee, PIN_OUTPUT_PULLDOWN | PIN_OFF_OUTPUT_LOW | MUX_MODE0)   /* dss_data9.dss_data9 */
198                         OMAP3_CORE1_IOPAD(0x20f0, PIN_OUTPUT_PULLDOWN | PIN_OFF_OUTPUT_LOW | MUX_MODE0)   /* dss_data10.dss_data10 */
199                         OMAP3_CORE1_IOPAD(0x20f2, PIN_OUTPUT_PULLDOWN | PIN_OFF_OUTPUT_LOW | MUX_MODE0)   /* dss_data11.dss_data11 */
200                         OMAP3_CORE1_IOPAD(0x20f4, PIN_OUTPUT_PULLDOWN | PIN_OFF_OUTPUT_LOW | MUX_MODE0)   /* dss_data12.dss_data12 */
201                         OMAP3_CORE1_IOPAD(0x20f6, PIN_OUTPUT_PULLDOWN | PIN_OFF_OUTPUT_LOW | MUX_MODE0)   /* dss_data13.dss_data13 */
202                         OMAP3_CORE1_IOPAD(0x20f8, PIN_OUTPUT_PULLDOWN | PIN_OFF_OUTPUT_LOW | MUX_MODE0)   /* dss_data14.dss_data14 */
203                         OMAP3_CORE1_IOPAD(0x20fa, PIN_OUTPUT_PULLDOWN | PIN_OFF_OUTPUT_LOW | MUX_MODE0)   /* dss_data15.dss_data15 */
204                 >;
205         };
208 &omap3_pmx_wkup {
209         led_pins_wkup: pinmux_led_pins_wkup {
210                 pinctrl-single,pins = <
211                         OMAP3_WKUP_IOPAD(0x2a24, PIN_OUTPUT_PULLUP | MUX_MODE4) /* jtag_emu0.gpio_11 / uP_GPIO_1 */
212                 >;
213         };
215         backlight_pins: pinmux_backlight_pins {
216                 pinctrl-single,pins = <
217                         OMAP3_WKUP_IOPAD(0x2a16, PIN_OUTPUT | PIN_OFF_OUTPUT_LOW | MUX_MODE4)       /* sys_boot6.gpio_8 */
218                 >;
219         };
223 &uart1 {
224         interrupts-extended = <&intc 72 &omap3_pmx_core OMAP3_UART1_RX>;
227 /* Wired to the tps65950 on the SOM, only the USB connector is on the devkit */
228 &usb_otg_hs {
229         pinctrl-names = "default";
230         pinctrl-0 = <&hsusb_otg_pins>;
231         interface-type = <0>;
232         usb-phy = <&usb2_phy>;
233         phys = <&usb2_phy>;
234         phy-names = "usb2-phy";
235         mode = <3>;
236         power = <50>;