arch/arm64/boot/dts/renesas/salvator-common.dtsi

   1 // SPDX-License-Identifier: GPL-2.0
   2 /*
   3  * Device Tree Source for common parts of Salvator-X board variants
   4  *
   5  * Copyright (C) 2015-2016 Renesas Electronics Corp.
   6  */
   7
   8 /*
   9  * SSI-AK4613
  10  *
  11  * This command is required when Playback/Capture
  12  *
  13  *      amixer set "DVC Out" 100%
  14  *      amixer set "DVC In" 100%
  15  *
  16  * You can use Mute
  17  *
  18  *      amixer set "DVC Out Mute" on
  19  *      amixer set "DVC In Mute" on
  20  *
  21  * You can use Volume Ramp
  22  *
  23  *      amixer set "DVC Out Ramp Up Rate"   "0.125 dB/64 steps"
  24  *      amixer set "DVC Out Ramp Down Rate" "0.125 dB/512 steps"
  25  *      amixer set "DVC Out Ramp" on
  26  *      aplay xxx.wav &
  27  *      amixer set "DVC Out"  80%  // Volume Down
  28  *      amixer set "DVC Out" 100%  // Volume Up
  29  */
  30
  31 #include <dt-bindings/gpio/gpio.h>
  32 #include <dt-bindings/input/input.h>
  33
  34 / {
  35         aliases {
  36                 serial0 = &scif2;
  37                 serial1 = &hscif1;
  38                 ethernet0 = &avb;
  39         };
  40
  41         chosen {
  42                 bootargs = "ignore_loglevel rw root=/dev/nfs ip=on";
  43                 stdout-path = "serial0:115200n8";
  44         };
  45
  46         audio_clkout: audio-clkout {
  47                 /*
  48                  * This is same as <&rcar_sound 0>
  49                  * but needed to avoid cs2000/rcar_sound probe dead-lock
  50                  */
  51                 compatible = "fixed-clock";
  52                 #clock-cells = <0>;
  53                 clock-frequency = <12288000>;
  54         };
  55
  56         backlight: backlight {
  57                 compatible = "pwm-backlight";
  58                 pwms = <&pwm1 0 50000>;
  59
  60                 brightness-levels = <256 128 64 16 8 4 0>;
  61                 default-brightness-level = <6>;
  62
  63                 power-supply = <&reg_12v>;
  64                 enable-gpios = <&gpio6 7 GPIO_ACTIVE_HIGH>;
  65         };
  66
  67         cvbs-in {
  68                 compatible = "composite-video-connector";
  69                 label = "CVBS IN";
  70
  71                 port {
  72                         cvbs_con: endpoint {
  73                                 remote-endpoint = <&adv7482_ain7>;
  74                         };
  75                 };
  76         };
  77
  78         hdmi-in {
  79                 compatible = "hdmi-connector";
  80                 label = "HDMI IN";
  81                 type = "a";
  82
  83                 port {
  84                         hdmi_in_con: endpoint {
  85                                 remote-endpoint = <&adv7482_hdmi>;
  86                         };
  87                 };
  88         };
  89
  90         hdmi0-out {
  91                 compatible = "hdmi-connector";
  92                 label = "HDMI0 OUT";
  93                 type = "a";
  94
  95                 port {
  96                         hdmi0_con: endpoint {
  97                         };
  98                 };
  99         };
 100
 101         hdmi1-out {
 102                 compatible = "hdmi-connector";
 103                 label = "HDMI1 OUT";
 104                 type = "a";
 105
 106                 port {
 107                         hdmi1_con: endpoint {
 108                         };
 109                 };
 110         };
 111
 112         keys {
 113                 compatible = "gpio-keys";
 114
 115                 pinctrl-0 = <&keys_pins>;
 116                 pinctrl-names = "default";
 117
 118                 key-1 {
 119                         gpios = <&gpio5 17 GPIO_ACTIVE_LOW>;
 120                         linux,code = <KEY_1>;
 121                         label = "SW4-1";
 122                         wakeup-source;
 123                         debounce-interval = <20>;
 124                 };
 125                 key-2 {
 126                         gpios = <&gpio5 20 GPIO_ACTIVE_LOW>;
 127                         linux,code = <KEY_2>;
 128                         label = "SW4-2";
 129                         wakeup-source;
 130                         debounce-interval = <20>;
 131                 };
 132                 key-3 {
 133                         gpios = <&gpio5 22 GPIO_ACTIVE_LOW>;
 134                         linux,code = <KEY_3>;
 135                         label = "SW4-3";
 136                         wakeup-source;
 137                         debounce-interval = <20>;
 138                 };
 139                 key-4 {
 140                         gpios = <&gpio5 23 GPIO_ACTIVE_LOW>;
 141                         linux,code = <KEY_4>;
 142                         label = "SW4-4";
 143                         wakeup-source;
 144                         debounce-interval = <20>;
 145                 };
 146                 key-a {
 147                         gpios = <&gpio6 11 GPIO_ACTIVE_LOW>;
 148                         linux,code = <KEY_A>;
 149                         label = "TSW0";
 150                         wakeup-source;
 151                         debounce-interval = <20>;
 152                 };
 153                 key-b {
 154                         gpios = <&gpio6 12 GPIO_ACTIVE_LOW>;
 155                         linux,code = <KEY_B>;
 156                         label = "TSW1";
 157                         wakeup-source;
 158                         debounce-interval = <20>;
 159                 };
 160                 key-c {
 161                         gpios = <&gpio6 13 GPIO_ACTIVE_LOW>;
 162                         linux,code = <KEY_C>;
 163                         label = "TSW2";
 164                         wakeup-source;
 165                         debounce-interval = <20>;
 166                 };
 167         };
 168
 169         reg_1p8v: regulator0 {
 170                 compatible = "regulator-fixed";
 171                 regulator-name = "fixed-1.8V";
 172                 regulator-min-microvolt = <1800000>;
 173                 regulator-max-microvolt = <1800000>;
 174                 regulator-boot-on;
 175                 regulator-always-on;
 176         };
 177
 178         reg_3p3v: regulator1 {
 179                 compatible = "regulator-fixed";
 180                 regulator-name = "fixed-3.3V";
 181                 regulator-min-microvolt = <3300000>;
 182                 regulator-max-microvolt = <3300000>;
 183                 regulator-boot-on;
 184                 regulator-always-on;
 185         };
 186
 187         reg_12v: regulator2 {
 188                 compatible = "regulator-fixed";
 189                 regulator-name = "fixed-12V";
 190                 regulator-min-microvolt = <12000000>;
 191                 regulator-max-microvolt = <12000000>;
 192                 regulator-boot-on;
 193                 regulator-always-on;
 194         };
 195
 196         sound_card: sound {
 197                 compatible = "audio-graph-card";
 198
 199                 label = "rcar-sound";
 200
 201                 dais = <&rsnd_port0>;
 202         };
 203
 204         vbus0_usb2: regulator-vbus0-usb2 {
 205                 compatible = "regulator-fixed";
 206
 207                 regulator-name = "USB20_VBUS0";
 208                 regulator-min-microvolt = <5000000>;
 209                 regulator-max-microvolt = <5000000>;
 210
 211                 gpio = <&gpio6 16 GPIO_ACTIVE_HIGH>;
 212                 enable-active-high;
 213         };
 214
 215         vcc_sdhi0: regulator-vcc-sdhi0 {
 216                 compatible = "regulator-fixed";
 217
 218                 regulator-name = "SDHI0 Vcc";
 219                 regulator-min-microvolt = <3300000>;
 220                 regulator-max-microvolt = <3300000>;
 221
 222                 gpio = <&gpio5 2 GPIO_ACTIVE_HIGH>;
 223                 enable-active-high;
 224         };
 225
 226         vccq_sdhi0: regulator-vccq-sdhi0 {
 227                 compatible = "regulator-gpio";
 228
 229                 regulator-name = "SDHI0 VccQ";
 230                 regulator-min-microvolt = <1800000>;
 231                 regulator-max-microvolt = <3300000>;
 232
 233                 gpios = <&gpio5 1 GPIO_ACTIVE_HIGH>;
 234                 gpios-states = <1>;
 235                 states = <3300000 1>, <1800000 0>;
 236         };
 237
 238         vcc_sdhi3: regulator-vcc-sdhi3 {
 239                 compatible = "regulator-fixed";
 240
 241                 regulator-name = "SDHI3 Vcc";
 242                 regulator-min-microvolt = <3300000>;
 243                 regulator-max-microvolt = <3300000>;
 244
 245                 gpio = <&gpio3 15 GPIO_ACTIVE_HIGH>;
 246                 enable-active-high;
 247         };
 248
 249         vccq_sdhi3: regulator-vccq-sdhi3 {
 250                 compatible = "regulator-gpio";
 251
 252                 regulator-name = "SDHI3 VccQ";
 253                 regulator-min-microvolt = <1800000>;
 254                 regulator-max-microvolt = <3300000>;
 255
 256                 gpios = <&gpio3 14 GPIO_ACTIVE_HIGH>;
 257                 gpios-states = <1>;
 258                 states = <3300000 1>, <1800000 0>;
 259         };
 260
 261         vga {
 262                 compatible = "vga-connector";
 263
 264                 port {
 265                         vga_in: endpoint {
 266                                 remote-endpoint = <&adv7123_out>;
 267                         };
 268                 };
 269         };
 270
 271         vga-encoder {
 272                 compatible = "adi,adv7123";
 273
 274                 ports {
 275                         #address-cells = <1>;
 276                         #size-cells = <0>;
 277
 278                         port@0 {
 279                                 reg = <0>;
 280                                 adv7123_in: endpoint {
 281                                         remote-endpoint = <&du_out_rgb>;
 282                                 };
 283                         };
 284                         port@1 {
 285                                 reg = <1>;
 286                                 adv7123_out: endpoint {
 287                                         remote-endpoint = <&vga_in>;
 288                                 };
 289                         };
 290                 };
 291         };
 292
 293         x12_clk: x12 {
 294                 compatible = "fixed-clock";
 295                 #clock-cells = <0>;
 296                 clock-frequency = <24576000>;
 297         };
 298
 299         /* External DU dot clocks */
 300         x21_clk: x21-clock {
 301                 compatible = "fixed-clock";
 302                 #clock-cells = <0>;
 303                 clock-frequency = <33000000>;
 304         };
 305
 306         x22_clk: x22-clock {
 307                 compatible = "fixed-clock";
 308                 #clock-cells = <0>;
 309                 clock-frequency = <33000000>;
 310         };
 311
 312         x23_clk: x23-clock {
 313                 compatible = "fixed-clock";
 314                 #clock-cells = <0>;
 315                 clock-frequency = <25000000>;
 316         };
 317 };
 318
 319 &audio_clk_a {
 320         clock-frequency = <22579200>;
 321 };
 322
 323 &avb {
 324         pinctrl-0 = <&avb_pins>;
 325         pinctrl-names = "default";
 326         phy-handle = <&phy0>;
 327         tx-internal-delay-ps = <2000>;
 328         status = "okay";
 329
 330         phy0: ethernet-phy@0 {
 331                 rxc-skew-ps = <1500>;
 332                 reg = <0>;
 333                 interrupt-parent = <&gpio2>;
 334                 interrupts = <11 IRQ_TYPE_LEVEL_LOW>;
 335                 reset-gpios = <&gpio2 10 GPIO_ACTIVE_LOW>;
 336         };
 337 };
 338
 339 &csi20 {
 340         status = "okay";
 341
 342         ports {
 343                 port@0 {
 344                         reg = <0>;
 345                         csi20_in: endpoint {
 346                                 clock-lanes = <0>;
 347                                 data-lanes = <1>;
 348                                 remote-endpoint = <&adv7482_txb>;
 349                         };
 350                 };
 351         };
 352 };
 353
 354 &csi40 {
 355         status = "okay";
 356
 357         ports {
 358                 port@0 {
 359                         reg = <0>;
 360
 361                         csi40_in: endpoint {
 362                                 clock-lanes = <0>;
 363                                 data-lanes = <1 2 3 4>;
 364                                 remote-endpoint = <&adv7482_txa>;
 365                         };
 366                 };
 367         };
 368 };
 369
 370 &du {
 371         pinctrl-0 = <&du_pins>;
 372         pinctrl-names = "default";
 373         status = "okay";
 374
 375         ports {
 376                 port@0 {
 377                         endpoint {
 378                                 remote-endpoint = <&adv7123_in>;
 379                         };
 380                 };
 381         };
 382 };
 383
 384 &ehci0 {
 385         dr_mode = "otg";
 386         status = "okay";
 387 };
 388
 389 &ehci1 {
 390         status = "okay";
 391 };
 392
 393 &extalr_clk {
 394         clock-frequency = <32768>;
 395 };
 396
 397 &hscif1 {
 398         pinctrl-0 = <&hscif1_pins>;
 399         pinctrl-names = "default";
 400
 401         uart-has-rtscts;
 402         /* Please only enable hscif1 or scif1 */
 403         status = "okay";
 404 };
 405
 406 &hsusb {
 407         dr_mode = "otg";
 408         status = "okay";
 409 };
 410
 411 &i2c2 {
 412         pinctrl-0 = <&i2c2_pins>;
 413         pinctrl-names = "default";
 414
 415         status = "okay";
 416
 417         clock-frequency = <100000>;
 418
 419         ak4613: codec@10 {
 420                 compatible = "asahi-kasei,ak4613";
 421                 #sound-dai-cells = <0>;
 422                 reg = <0x10>;
 423                 clocks = <&rcar_sound 3>;
 424
 425                 asahi-kasei,in1-single-end;
 426                 asahi-kasei,in2-single-end;
 427                 asahi-kasei,out1-single-end;
 428                 asahi-kasei,out2-single-end;
 429                 asahi-kasei,out3-single-end;
 430                 asahi-kasei,out4-single-end;
 431                 asahi-kasei,out5-single-end;
 432                 asahi-kasei,out6-single-end;
 433
 434                 port {
 435                         ak4613_endpoint: endpoint {
 436                                 remote-endpoint = <&rsnd_endpoint0>;
 437                         };
 438                 };
 439         };
 440
 441         cs2000: clk_multiplier@4f {
 442                 #clock-cells = <0>;
 443                 compatible = "cirrus,cs2000-cp";
 444                 reg = <0x4f>;
 445                 clocks = <&audio_clkout>, <&x12_clk>;
 446                 clock-names = "clk_in", "ref_clk";
 447
 448                 assigned-clocks = <&cs2000>;
 449                 assigned-clock-rates = <24576000>; /* 1/1 divide */
 450         };
 451 };
 452
 453 &i2c4 {
 454         status = "okay";
 455
 456         pca9654: gpio@20 {
 457                 compatible = "onnn,pca9654";
 458                 reg = <0x20>;
 459                 gpio-controller;
 460                 #gpio-cells = <2>;
 461         };
 462
 463         video-receiver@70 {
 464                 compatible = "adi,adv7482";
 465                 reg = <0x70 0x71 0x72 0x73 0x74 0x75
 466                        0x60 0x61 0x62 0x63 0x64 0x65>;
 467                 reg-names = "main", "dpll", "cp", "hdmi", "edid", "repeater",
 468                             "infoframe", "cbus", "cec", "sdp", "txa", "txb" ;
 469
 470                 #address-cells = <1>;
 471                 #size-cells = <0>;
 472
 473                 interrupt-parent = <&gpio6>;
 474                 interrupt-names = "intrq1", "intrq2";
 475                 interrupts = <30 IRQ_TYPE_LEVEL_LOW>,
 476                              <31 IRQ_TYPE_LEVEL_LOW>;
 477
 478                 port@7 {
 479                         reg = <7>;
 480
 481                         adv7482_ain7: endpoint {
 482                                 remote-endpoint = <&cvbs_con>;
 483                         };
 484                 };
 485
 486                 port@8 {
 487                         reg = <8>;
 488
 489                         adv7482_hdmi: endpoint {
 490                                 remote-endpoint = <&hdmi_in_con>;
 491                         };
 492                 };
 493
 494                 port@a {
 495                         reg = <10>;
 496
 497                         adv7482_txa: endpoint {
 498                                 clock-lanes = <0>;
 499                                 data-lanes = <1 2 3 4>;
 500                                 remote-endpoint = <&csi40_in>;
 501                         };
 502                 };
 503
 504                 port@b {
 505                         reg = <11>;
 506
 507                         adv7482_txb: endpoint {
 508                                 clock-lanes = <0>;
 509                                 data-lanes = <1>;
 510                                 remote-endpoint = <&csi20_in>;
 511                         };
 512                 };
 513         };
 514
 515         csa_vdd: adc@7c {
 516                 compatible = "maxim,max9611";
 517                 reg = <0x7c>;
 518
 519                 shunt-resistor-micro-ohms = <5000>;
 520         };
 521
 522         csa_dvfs: adc@7f {
 523                 compatible = "maxim,max9611";
 524                 reg = <0x7f>;
 525
 526                 shunt-resistor-micro-ohms = <5000>;
 527         };
 528 };
 529
 530 &i2c_dvfs {
 531         status = "okay";
 532
 533         clock-frequency = <400000>;
 534
 535         pmic: pmic@30 {
 536                 pinctrl-0 = <&irq0_pins>;
 537                 pinctrl-names = "default";
 538
 539                 compatible = "rohm,bd9571mwv";
 540                 reg = <0x30>;
 541                 interrupt-parent = <&intc_ex>;
 542                 interrupts = <0 IRQ_TYPE_LEVEL_LOW>;
 543                 interrupt-controller;
 544                 #interrupt-cells = <2>;
 545                 gpio-controller;
 546                 #gpio-cells = <2>;
 547                 rohm,ddr-backup-power = <0xf>;
 548                 rohm,rstbmode-level;
 549
 550                 regulators {
 551                         dvfs: dvfs {
 552                                 regulator-name = "dvfs";
 553                                 regulator-min-microvolt = <750000>;
 554                                 regulator-max-microvolt = <1030000>;
 555                                 regulator-boot-on;
 556                                 regulator-always-on;
 557                         };
 558                 };
 559         };
 560
 561         eeprom@50 {
 562                 compatible = "rohm,br24t01", "atmel,24c01";
 563                 reg = <0x50>;
 564                 pagesize = <8>;
 565         };
 566 };
 567
 568 &ohci0 {
 569         dr_mode = "otg";
 570         status = "okay";
 571 };
 572
 573 &ohci1 {
 574         status = "okay";
 575 };
 576
 577 &pcie_bus_clk {
 578         clock-frequency = <100000000>;
 579 };
 580
 581 &pciec0 {
 582         status = "okay";
 583 };
 584
 585 &pciec1 {
 586         status = "okay";
 587 };
 588
 589 &pfc {
 590         pinctrl-0 = <&scif_clk_pins>;
 591         pinctrl-names = "default";
 592
 593         avb_pins: avb {
 594                 mux {
 595                         groups = "avb_link", "avb_mdio", "avb_mii";
 596                         function = "avb";
 597                 };
 598
 599                 pins_mdio {
 600                         groups = "avb_mdio";
 601                         drive-strength = <24>;
 602                 };
 603
 604                 pins_mii_tx {
 605                         pins = "PIN_AVB_TX_CTL", "PIN_AVB_TXC", "PIN_AVB_TD0",
 606                                "PIN_AVB_TD1", "PIN_AVB_TD2", "PIN_AVB_TD3";
 607                         drive-strength = <12>;
 608                 };
 609         };
 610
 611         du_pins: du {
 612                 groups = "du_rgb888", "du_sync", "du_oddf", "du_clk_out_0";
 613                 function = "du";
 614         };
 615
 616         hscif1_pins: hscif1 {
 617                 groups = "hscif1_data_a", "hscif1_ctrl_a";
 618                 function = "hscif1";
 619         };
 620
 621         i2c2_pins: i2c2 {
 622                 groups = "i2c2_a";
 623                 function = "i2c2";
 624         };
 625
 626         irq0_pins: irq0 {
 627                 groups = "intc_ex_irq0";
 628                 function = "intc_ex";
 629         };
 630
 631         keys_pins: keys {
 632                 pins = "GP_5_17", "GP_5_20", "GP_5_22";
 633                 bias-pull-up;
 634         };
 635
 636         pwm1_pins: pwm1 {
 637                 groups = "pwm1_a";
 638                 function = "pwm1";
 639         };
 640
 641         scif1_pins: scif1 {
 642                 groups = "scif1_data_a", "scif1_ctrl";
 643                 function = "scif1";
 644         };
 645
 646         scif2_pins: scif2 {
 647                 groups = "scif2_data_a";
 648                 function = "scif2";
 649         };
 650
 651         scif_clk_pins: scif_clk {
 652                 groups = "scif_clk_a";
 653                 function = "scif_clk";
 654         };
 655
 656         sdhi0_pins: sd0 {
 657                 groups = "sdhi0_data4", "sdhi0_ctrl";
 658                 function = "sdhi0";
 659                 power-source = <3300>;
 660         };
 661
 662         sdhi0_pins_uhs: sd0_uhs {
 663                 groups = "sdhi0_data4", "sdhi0_ctrl";
 664                 function = "sdhi0";
 665                 power-source = <1800>;
 666         };
 667
 668         sdhi2_pins: sd2 {
 669                 groups = "sdhi2_data8", "sdhi2_ctrl", "sdhi2_ds";
 670                 function = "sdhi2";
 671                 power-source = <1800>;
 672         };
 673
 674         sdhi3_pins: sd3 {
 675                 groups = "sdhi3_data4", "sdhi3_ctrl";
 676                 function = "sdhi3";
 677                 power-source = <3300>;
 678         };
 679
 680         sdhi3_pins_uhs: sd3_uhs {
 681                 groups = "sdhi3_data4", "sdhi3_ctrl";
 682                 function = "sdhi3";
 683                 power-source = <1800>;
 684         };
 685
 686         sound_pins: sound {
 687                 groups = "ssi01239_ctrl", "ssi0_data", "ssi1_data_a";
 688                 function = "ssi";
 689         };
 690
 691         sound_clk_pins: sound_clk {
 692                 groups = "audio_clk_a_a", "audio_clk_b_a", "audio_clk_c_a",
 693                          "audio_clkout_a", "audio_clkout3_a";
 694                 function = "audio_clk";
 695         };
 696
 697         usb0_pins: usb0 {
 698                 groups = "usb0";
 699                 function = "usb0";
 700         };
 701
 702         usb1_pins: usb1 {
 703                 mux {
 704                         groups = "usb1";
 705                         function = "usb1";
 706                 };
 707
 708                 ovc {
 709                         pins = "GP_6_27";
 710                         bias-pull-up;
 711                 };
 712
 713                 pwen {
 714                         pins = "GP_6_26";
 715                         bias-pull-down;
 716                 };
 717         };
 718
 719         usb30_pins: usb30 {
 720                 groups = "usb30";
 721                 function = "usb30";
 722         };
 723 };
 724
 725 &pwm1 {
 726         pinctrl-0 = <&pwm1_pins>;
 727         pinctrl-names = "default";
 728
 729         status = "okay";
 730 };
 731
 732 &rcar_sound {
 733         pinctrl-0 = <&sound_pins &sound_clk_pins>;
 734         pinctrl-names = "default";
 735
 736         /* Single DAI */
 737         #sound-dai-cells = <0>;
 738
 739         /* audio_clkout0/1/2/3 */
 740         #clock-cells = <1>;
 741         clock-frequency = <12288000 11289600>;
 742
 743         status = "okay";
 744
 745         /* update <audio_clk_b> to <cs2000> */
 746         clocks = <&cpg CPG_MOD 1005>,
 747                  <&cpg CPG_MOD 1006>, <&cpg CPG_MOD 1007>,
 748                  <&cpg CPG_MOD 1008>, <&cpg CPG_MOD 1009>,
 749                  <&cpg CPG_MOD 1010>, <&cpg CPG_MOD 1011>,
 750                  <&cpg CPG_MOD 1012>, <&cpg CPG_MOD 1013>,
 751                  <&cpg CPG_MOD 1014>, <&cpg CPG_MOD 1015>,
 752                  <&cpg CPG_MOD 1022>, <&cpg CPG_MOD 1023>,
 753                  <&cpg CPG_MOD 1024>, <&cpg CPG_MOD 1025>,
 754                  <&cpg CPG_MOD 1026>, <&cpg CPG_MOD 1027>,
 755                  <&cpg CPG_MOD 1028>, <&cpg CPG_MOD 1029>,
 756                  <&cpg CPG_MOD 1030>, <&cpg CPG_MOD 1031>,
 757                  <&cpg CPG_MOD 1020>, <&cpg CPG_MOD 1021>,
 758                  <&cpg CPG_MOD 1020>, <&cpg CPG_MOD 1021>,
 759                  <&cpg CPG_MOD 1019>, <&cpg CPG_MOD 1018>,
 760                  <&audio_clk_a>, <&cs2000>,
 761                  <&audio_clk_c>,
 762                  <&cpg CPG_CORE CPG_AUDIO_CLK_I>;
 763
 764         ports {
 765                 #address-cells = <1>;
 766                 #size-cells = <0>;
 767                 rsnd_port0: port@0 {
 768                         reg = <0>;
 769                         rsnd_endpoint0: endpoint {
 770                                 remote-endpoint = <&ak4613_endpoint>;
 771
 772                                 dai-format = "left_j";
 773                                 bitclock-master = <&rsnd_endpoint0>;
 774                                 frame-master = <&rsnd_endpoint0>;
 775
 776                                 playback = <&ssi0 &src0 &dvc0>;
 777                                 capture  = <&ssi1 &src1 &dvc1>;
 778                         };
 779                 };
 780         };
 781 };
 782
 783 &rwdt {
 784         timeout-sec = <60>;
 785         status = "okay";
 786 };
 787
 788 &scif1 {
 789         pinctrl-0 = <&scif1_pins>;
 790         pinctrl-names = "default";
 791
 792         uart-has-rtscts;
 793         /* Please only enable hscif1 or scif1 */
 794         /* status = "okay"; */
 795 };
 796
 797 &scif2 {
 798         pinctrl-0 = <&scif2_pins>;
 799         pinctrl-names = "default";
 800
 801         status = "okay";
 802 };
 803
 804 &scif_clk {
 805         clock-frequency = <14745600>;
 806 };
 807
 808 &sdhi0 {
 809         pinctrl-0 = <&sdhi0_pins>;
 810         pinctrl-1 = <&sdhi0_pins_uhs>;
 811         pinctrl-names = "default", "state_uhs";
 812
 813         vmmc-supply = <&vcc_sdhi0>;
 814         vqmmc-supply = <&vccq_sdhi0>;
 815         cd-gpios = <&gpio3 12 GPIO_ACTIVE_LOW>;
 816         wp-gpios = <&gpio3 13 GPIO_ACTIVE_HIGH>;
 817         bus-width = <4>;
 818         sd-uhs-sdr50;
 819         sd-uhs-sdr104;
 820         status = "okay";
 821 };
 822
 823 &sdhi2 {
 824         /* used for on-board 8bit eMMC */
 825         pinctrl-0 = <&sdhi2_pins>;
 826         pinctrl-1 = <&sdhi2_pins>;
 827         pinctrl-names = "default", "state_uhs";
 828
 829         vmmc-supply = <&reg_3p3v>;
 830         vqmmc-supply = <&reg_1p8v>;
 831         bus-width = <8>;
 832         mmc-hs200-1_8v;
 833         mmc-hs400-1_8v;
 834         non-removable;
 835         fixed-emmc-driver-type = <1>;
 836         full-pwr-cycle-in-suspend;
 837         status = "okay";
 838 };
 839
 840 &sdhi3 {
 841         pinctrl-0 = <&sdhi3_pins>;
 842         pinctrl-1 = <&sdhi3_pins_uhs>;
 843         pinctrl-names = "default", "state_uhs";
 844
 845         vmmc-supply = <&vcc_sdhi3>;
 846         vqmmc-supply = <&vccq_sdhi3>;
 847         cd-gpios = <&gpio4 15 GPIO_ACTIVE_LOW>;
 848         wp-gpios = <&gpio4 16 GPIO_ACTIVE_HIGH>;
 849         bus-width = <4>;
 850         sd-uhs-sdr50;
 851         sd-uhs-sdr104;
 852         status = "okay";
 853 };
 854
 855 &ssi1 {
 856         shared-pin;
 857 };
 858
 859 &usb_extal_clk {
 860         clock-frequency = <50000000>;
 861 };
 862
 863 &usb2_phy0 {
 864         pinctrl-0 = <&usb0_pins>;
 865         pinctrl-names = "default";
 866
 867         vbus-supply = <&vbus0_usb2>;
 868         status = "okay";
 869 };
 870
 871 &usb2_phy1 {
 872         pinctrl-0 = <&usb1_pins>;
 873         pinctrl-names = "default";
 874
 875         status = "okay";
 876 };
 877
 878 &usb3_peri0 {
 879         phys = <&usb3_phy0>;
 880         phy-names = "usb";
 881
 882         companion = <&xhci0>;
 883
 884         status = "okay";
 885 };
 886
 887 &usb3_phy0 {
 888         status = "okay";
 889 };
 890
 891 &usb3s0_clk {
 892         clock-frequency = <100000000>;
 893 };
 894
 895 &vin0 {
 896         status = "okay";
 897 };
 898
 899 &vin1 {
 900         status = "okay";
 901 };
 902
 903 &vin2 {
 904         status = "okay";
 905 };
 906
 907 &vin3 {
 908         status = "okay";
 909 };
 910
 911 &vin4 {
 912         status = "okay";
 913 };
 914
 915 &vin5 {
 916         status = "okay";
 917 };
 918
 919 &vin6 {
 920         status = "okay";
 921 };
 922
 923 &vin7 {
 924         status = "okay";
 925 };
 926
 927 &xhci0 {
 928         pinctrl-0 = <&usb30_pins>;
 929         pinctrl-names = "default";
 930
 931         status = "okay";
 932 };