WIP FPC-III support
[linux/fpc-iii.git] / arch / mips / netlogic / xlp / ahci-init.c
blob92be1a3258b1615697607d951dd1045469bad36e
1 /*
2 * Copyright (c) 2003-2014 Broadcom Corporation
3 * All Rights Reserved
5 * This software is available to you under a choice of one of two
6 * licenses. You may choose to be licensed under the terms of the GNU
7 * General Public License (GPL) Version 2, available from the file
8 * COPYING in the main directory of this source tree, or the Broadcom
9 * license below:
11 * Redistribution and use in source and binary forms, with or without
12 * modification, are permitted provided that the following conditions
13 * are met:
15 * 1. Redistributions of source code must retain the above copyright
16 * notice, this list of conditions and the following disclaimer.
17 * 2. Redistributions in binary form must reproduce the above copyright
18 * notice, this list of conditions and the following disclaimer in
19 * the documentation and/or other materials provided with the
20 * distribution.
22 * THIS SOFTWARE IS PROVIDED BY BROADCOM ``AS IS'' AND ANY EXPRESS OR
23 * IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED
24 * WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE
25 * ARE DISCLAIMED. IN NO EVENT SHALL BROADCOM OR CONTRIBUTORS BE LIABLE
26 * FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR
27 * CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF
28 * SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR
29 * BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY,
30 * WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE
31 * OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN
32 * IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
35 #include <linux/dma-mapping.h>
36 #include <linux/kernel.h>
37 #include <linux/delay.h>
38 #include <linux/init.h>
39 #include <linux/pci.h>
40 #include <linux/irq.h>
41 #include <linux/bitops.h>
43 #include <asm/cpu.h>
44 #include <asm/mipsregs.h>
46 #include <asm/netlogic/haldefs.h>
47 #include <asm/netlogic/xlp-hal/xlp.h>
48 #include <asm/netlogic/common.h>
49 #include <asm/netlogic/xlp-hal/iomap.h>
50 #include <asm/netlogic/mips-extns.h>
52 #define SATA_CTL 0x0
53 #define SATA_STATUS 0x1 /* Status Reg */
54 #define SATA_INT 0x2 /* Interrupt Reg */
55 #define SATA_INT_MASK 0x3 /* Interrupt Mask Reg */
56 #define SATA_CR_REG_TIMER 0x4 /* PHY Conrol Timer Reg */
57 #define SATA_CORE_ID 0x5 /* Core ID Reg */
58 #define SATA_AXI_SLAVE_OPT1 0x6 /* AXI Slave Options Reg */
59 #define SATA_PHY_LOS_LEV 0x7 /* PHY LOS Level Reg */
60 #define SATA_PHY_MULTI 0x8 /* PHY Multiplier Reg */
61 #define SATA_PHY_CLK_SEL 0x9 /* Clock Select Reg */
62 #define SATA_PHY_AMP1_GEN1 0xa /* PHY Transmit Amplitude Reg 1 */
63 #define SATA_PHY_AMP1_GEN2 0xb /* PHY Transmit Amplitude Reg 2 */
64 #define SATA_PHY_AMP1_GEN3 0xc /* PHY Transmit Amplitude Reg 3 */
65 #define SATA_PHY_PRE1 0xd /* PHY Transmit Preemphasis Reg 1 */
66 #define SATA_PHY_PRE2 0xe /* PHY Transmit Preemphasis Reg 2 */
67 #define SATA_PHY_PRE3 0xf /* PHY Transmit Preemphasis Reg 3 */
68 #define SATA_SPDMODE 0x10 /* Speed Mode Reg */
69 #define SATA_REFCLK 0x11 /* Reference Clock Control Reg */
70 #define SATA_BYTE_SWAP_DIS 0x12 /* byte swap disable */
72 /*SATA_CTL Bits */
73 #define SATA_RST_N BIT(0)
74 #define PHY0_RESET_N BIT(16)
75 #define PHY1_RESET_N BIT(17)
76 #define PHY2_RESET_N BIT(18)
77 #define PHY3_RESET_N BIT(19)
78 #define M_CSYSREQ BIT(2)
79 #define S_CSYSREQ BIT(3)
81 /*SATA_STATUS Bits */
82 #define P0_PHY_READY BIT(4)
83 #define P1_PHY_READY BIT(5)
84 #define P2_PHY_READY BIT(6)
85 #define P3_PHY_READY BIT(7)
87 #define nlm_read_sata_reg(b, r) nlm_read_reg(b, r)
88 #define nlm_write_sata_reg(b, r, v) nlm_write_reg(b, r, v)
89 #define nlm_get_sata_pcibase(node) \
90 nlm_pcicfg_base(XLP_IO_SATA_OFFSET(node))
91 /* SATA device specific configuration registers are starts at 0x900 offset */
92 #define nlm_get_sata_regbase(node) \
93 (nlm_get_sata_pcibase(node) + 0x900)
95 static void sata_clear_glue_reg(uint64_t regbase, uint32_t off, uint32_t bit)
97 uint32_t reg_val;
99 reg_val = nlm_read_sata_reg(regbase, off);
100 nlm_write_sata_reg(regbase, off, (reg_val & ~bit));
103 static void sata_set_glue_reg(uint64_t regbase, uint32_t off, uint32_t bit)
105 uint32_t reg_val;
107 reg_val = nlm_read_sata_reg(regbase, off);
108 nlm_write_sata_reg(regbase, off, (reg_val | bit));
111 static void nlm_sata_firmware_init(int node)
113 uint32_t reg_val;
114 uint64_t regbase;
115 int i;
117 pr_info("XLP AHCI Initialization started.\n");
118 regbase = nlm_get_sata_regbase(node);
120 /* Reset SATA */
121 sata_clear_glue_reg(regbase, SATA_CTL, SATA_RST_N);
122 /* Reset PHY */
123 sata_clear_glue_reg(regbase, SATA_CTL,
124 (PHY3_RESET_N | PHY2_RESET_N
125 | PHY1_RESET_N | PHY0_RESET_N));
127 /* Set SATA */
128 sata_set_glue_reg(regbase, SATA_CTL, SATA_RST_N);
129 /* Set PHY */
130 sata_set_glue_reg(regbase, SATA_CTL,
131 (PHY3_RESET_N | PHY2_RESET_N
132 | PHY1_RESET_N | PHY0_RESET_N));
134 pr_debug("Waiting for PHYs to come up.\n");
135 i = 0;
136 do {
137 reg_val = nlm_read_sata_reg(regbase, SATA_STATUS);
138 i++;
139 } while (((reg_val & 0xF0) != 0xF0) && (i < 10000));
141 for (i = 0; i < 4; i++) {
142 if (reg_val & (P0_PHY_READY << i))
143 pr_info("PHY%d is up.\n", i);
144 else
145 pr_info("PHY%d is down.\n", i);
148 pr_info("XLP AHCI init done.\n");
151 static int __init nlm_ahci_init(void)
153 int node = 0;
154 int chip = read_c0_prid() & PRID_IMP_MASK;
156 if (chip == PRID_IMP_NETLOGIC_XLP3XX)
157 nlm_sata_firmware_init(node);
158 return 0;
161 static void nlm_sata_intr_ack(struct irq_data *data)
163 uint32_t val = 0;
164 uint64_t regbase;
166 regbase = nlm_get_sata_regbase(nlm_nodeid());
167 val = nlm_read_sata_reg(regbase, SATA_INT);
168 sata_set_glue_reg(regbase, SATA_INT, val);
171 static void nlm_sata_fixup_bar(struct pci_dev *dev)
174 * The AHCI resource is in BAR 0, move it to
175 * BAR 5, where it is expected
177 dev->resource[5] = dev->resource[0];
178 memset(&dev->resource[0], 0, sizeof(dev->resource[0]));
181 static void nlm_sata_fixup_final(struct pci_dev *dev)
183 uint32_t val;
184 uint64_t regbase;
185 int node = 0; /* XLP3XX does not support multi-node */
187 regbase = nlm_get_sata_regbase(node);
189 /* clear pending interrupts and then enable them */
190 val = nlm_read_sata_reg(regbase, SATA_INT);
191 sata_set_glue_reg(regbase, SATA_INT, val);
193 /* Mask the core interrupt. If all the interrupts
194 * are enabled there are spurious interrupt flow
195 * happening, to avoid only enable core interrupt
196 * mask.
198 sata_set_glue_reg(regbase, SATA_INT_MASK, 0x1);
200 dev->irq = PIC_SATA_IRQ;
201 nlm_set_pic_extra_ack(node, PIC_SATA_IRQ, nlm_sata_intr_ack);
204 arch_initcall(nlm_ahci_init);
206 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_NETLOGIC, PCI_DEVICE_ID_NLM_SATA,
207 nlm_sata_fixup_bar);
208 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_NETLOGIC, PCI_DEVICE_ID_NLM_SATA,
209 nlm_sata_fixup_final);