drivers/char/tpm/st33zp24/i2c.c

   1 // SPDX-License-Identifier: GPL-2.0-or-later
   2 /*
   3  * STMicroelectronics TPM I2C Linux driver for TPM ST33ZP24
   4  * Copyright (C) 2009 - 2016 STMicroelectronics
   5  */
   6
   7 #include <linux/module.h>
   8 #include <linux/i2c.h>
   9 #include <linux/gpio.h>
  10 #include <linux/gpio/consumer.h>
  11 #include <linux/of_irq.h>
  12 #include <linux/of_gpio.h>
  13 #include <linux/acpi.h>
  14 #include <linux/tpm.h>
  15 #include <linux/platform_data/st33zp24.h>
  16
  17 #include "../tpm.h"
  18 #include "st33zp24.h"
  19
  20 #define TPM_DUMMY_BYTE                  0xAA
  21
  22 struct st33zp24_i2c_phy {
  23         struct i2c_client *client;
  24         u8 buf[ST33ZP24_BUFSIZE + 1];
  25         int io_lpcpd;
  26 };
  27
  28 /*
  29  * write8_reg
  30  * Send byte to the TIS register according to the ST33ZP24 I2C protocol.
  31  * @param: tpm_register, the tpm tis register where the data should be written
  32  * @param: tpm_data, the tpm_data to write inside the tpm_register
  33  * @param: tpm_size, The length of the data
  34  * @return: Returns negative errno, or else the number of bytes written.
  35  */
  36 static int write8_reg(void *phy_id, u8 tpm_register, u8 *tpm_data, int tpm_size)
  37 {
  38         struct st33zp24_i2c_phy *phy = phy_id;
  39
  40         phy->buf[0] = tpm_register;
  41         memcpy(phy->buf + 1, tpm_data, tpm_size);
  42         return i2c_master_send(phy->client, phy->buf, tpm_size + 1);
  43 } /* write8_reg() */
  44
  45 /*
  46  * read8_reg
  47  * Recv byte from the TIS register according to the ST33ZP24 I2C protocol.
  48  * @param: tpm_register, the tpm tis register where the data should be read
  49  * @param: tpm_data, the TPM response
  50  * @param: tpm_size, tpm TPM response size to read.
  51  * @return: number of byte read successfully: should be one if success.
  52  */
  53 static int read8_reg(void *phy_id, u8 tpm_register, u8 *tpm_data, int tpm_size)
  54 {
  55         struct st33zp24_i2c_phy *phy = phy_id;
  56         u8 status = 0;
  57         u8 data;
  58
  59         data = TPM_DUMMY_BYTE;
  60         status = write8_reg(phy, tpm_register, &data, 1);
  61         if (status == 2)
  62                 status = i2c_master_recv(phy->client, tpm_data, tpm_size);
  63         return status;
  64 } /* read8_reg() */
  65
  66 /*
  67  * st33zp24_i2c_send
  68  * Send byte to the TIS register according to the ST33ZP24 I2C protocol.
  69  * @param: phy_id, the phy description
  70  * @param: tpm_register, the tpm tis register where the data should be written
  71  * @param: tpm_data, the tpm_data to write inside the tpm_register
  72  * @param: tpm_size, the length of the data
  73  * @return: number of byte written successfully: should be one if success.
  74  */
  75 static int st33zp24_i2c_send(void *phy_id, u8 tpm_register, u8 *tpm_data,
  76                              int tpm_size)
  77 {
  78         return write8_reg(phy_id, tpm_register | TPM_WRITE_DIRECTION, tpm_data,
  79                           tpm_size);
  80 }
  81
  82 /*
  83  * st33zp24_i2c_recv
  84  * Recv byte from the TIS register according to the ST33ZP24 I2C protocol.
  85  * @param: phy_id, the phy description
  86  * @param: tpm_register, the tpm tis register where the data should be read
  87  * @param: tpm_data, the TPM response
  88  * @param: tpm_size, tpm TPM response size to read.
  89  * @return: number of byte read successfully: should be one if success.
  90  */
  91 static int st33zp24_i2c_recv(void *phy_id, u8 tpm_register, u8 *tpm_data,
  92                              int tpm_size)
  93 {
  94         return read8_reg(phy_id, tpm_register, tpm_data, tpm_size);
  95 }
  96
  97 static const struct st33zp24_phy_ops i2c_phy_ops = {
  98         .send = st33zp24_i2c_send,
  99         .recv = st33zp24_i2c_recv,
 100 };
 101
 102 static const struct acpi_gpio_params lpcpd_gpios = { 1, 0, false };
 103
 104 static const struct acpi_gpio_mapping acpi_st33zp24_gpios[] = {
 105         { "lpcpd-gpios", &lpcpd_gpios, 1 },
 106         {},
 107 };
 108
 109 static int st33zp24_i2c_acpi_request_resources(struct i2c_client *client)
 110 {
 111         struct tpm_chip *chip = i2c_get_clientdata(client);
 112         struct st33zp24_dev *tpm_dev = dev_get_drvdata(&chip->dev);
 113         struct st33zp24_i2c_phy *phy = tpm_dev->phy_id;
 114         struct gpio_desc *gpiod_lpcpd;
 115         struct device *dev = &client->dev;
 116         int ret;
 117
 118         ret = devm_acpi_dev_add_driver_gpios(dev, acpi_st33zp24_gpios);
 119         if (ret)
 120                 return ret;
 121
 122         /* Get LPCPD GPIO from ACPI */
 123         gpiod_lpcpd = devm_gpiod_get(dev, "lpcpd", GPIOD_OUT_HIGH);
 124         if (IS_ERR(gpiod_lpcpd)) {
 125                 dev_err(&client->dev,
 126                         "Failed to retrieve lpcpd-gpios from acpi.\n");
 127                 phy->io_lpcpd = -1;
 128                 /*
 129                  * lpcpd pin is not specified. This is not an issue as
 130                  * power management can be also managed by TPM specific
 131                  * commands. So leave with a success status code.
 132                  */
 133                 return 0;
 134         }
 135
 136         phy->io_lpcpd = desc_to_gpio(gpiod_lpcpd);
 137
 138         return 0;
 139 }
 140
 141 static int st33zp24_i2c_of_request_resources(struct i2c_client *client)
 142 {
 143         struct tpm_chip *chip = i2c_get_clientdata(client);
 144         struct st33zp24_dev *tpm_dev = dev_get_drvdata(&chip->dev);
 145         struct st33zp24_i2c_phy *phy = tpm_dev->phy_id;
 146         struct device_node *pp;
 147         int gpio;
 148         int ret;
 149
 150         pp = client->dev.of_node;
 151         if (!pp) {
 152                 dev_err(&client->dev, "No platform data\n");
 153                 return -ENODEV;
 154         }
 155
 156         /* Get GPIO from device tree */
 157         gpio = of_get_named_gpio(pp, "lpcpd-gpios", 0);
 158         if (gpio < 0) {
 159                 dev_err(&client->dev,
 160                         "Failed to retrieve lpcpd-gpios from dts.\n");
 161                 phy->io_lpcpd = -1;
 162                 /*
 163                  * lpcpd pin is not specified. This is not an issue as
 164                  * power management can be also managed by TPM specific
 165                  * commands. So leave with a success status code.
 166                  */
 167                 return 0;
 168         }
 169         /* GPIO request and configuration */
 170         ret = devm_gpio_request_one(&client->dev, gpio,
 171                         GPIOF_OUT_INIT_HIGH, "TPM IO LPCPD");
 172         if (ret) {
 173                 dev_err(&client->dev, "Failed to request lpcpd pin\n");
 174                 return -ENODEV;
 175         }
 176         phy->io_lpcpd = gpio;
 177
 178         return 0;
 179 }
 180
 181 static int st33zp24_i2c_request_resources(struct i2c_client *client)
 182 {
 183         struct tpm_chip *chip = i2c_get_clientdata(client);
 184         struct st33zp24_dev *tpm_dev = dev_get_drvdata(&chip->dev);
 185         struct st33zp24_i2c_phy *phy = tpm_dev->phy_id;
 186         struct st33zp24_platform_data *pdata;
 187         int ret;
 188
 189         pdata = client->dev.platform_data;
 190         if (!pdata) {
 191                 dev_err(&client->dev, "No platform data\n");
 192                 return -ENODEV;
 193         }
 194
 195         /* store for late use */
 196         phy->io_lpcpd = pdata->io_lpcpd;
 197
 198         if (gpio_is_valid(pdata->io_lpcpd)) {
 199                 ret = devm_gpio_request_one(&client->dev,
 200                                 pdata->io_lpcpd, GPIOF_OUT_INIT_HIGH,
 201                                 "TPM IO_LPCPD");
 202                 if (ret) {
 203                         dev_err(&client->dev, "Failed to request lpcpd pin\n");
 204                         return ret;
 205                 }
 206         }
 207
 208         return 0;
 209 }
 210
 211 /*
 212  * st33zp24_i2c_probe initialize the TPM device
 213  * @param: client, the i2c_client description (TPM I2C description).
 214  * @param: id, the i2c_device_id struct.
 215  * @return: 0 in case of success.
 216  *       -1 in other case.
 217  */
 218 static int st33zp24_i2c_probe(struct i2c_client *client,
 219                               const struct i2c_device_id *id)
 220 {
 221         int ret;
 222         struct st33zp24_platform_data *pdata;
 223         struct st33zp24_i2c_phy *phy;
 224
 225         if (!client) {
 226                 pr_info("%s: i2c client is NULL. Device not accessible.\n",
 227                         __func__);
 228                 return -ENODEV;
 229         }
 230
 231         if (!i2c_check_functionality(client->adapter, I2C_FUNC_I2C)) {
 232                 dev_info(&client->dev, "client not i2c capable\n");
 233                 return -ENODEV;
 234         }
 235
 236         phy = devm_kzalloc(&client->dev, sizeof(struct st33zp24_i2c_phy),
 237                            GFP_KERNEL);
 238         if (!phy)
 239                 return -ENOMEM;
 240
 241         phy->client = client;
 242
 243         pdata = client->dev.platform_data;
 244         if (!pdata && client->dev.of_node) {
 245                 ret = st33zp24_i2c_of_request_resources(client);
 246                 if (ret)
 247                         return ret;
 248         } else if (pdata) {
 249                 ret = st33zp24_i2c_request_resources(client);
 250                 if (ret)
 251                         return ret;
 252         } else if (ACPI_HANDLE(&client->dev)) {
 253                 ret = st33zp24_i2c_acpi_request_resources(client);
 254                 if (ret)
 255                         return ret;
 256         }
 257
 258         return st33zp24_probe(phy, &i2c_phy_ops, &client->dev, client->irq,
 259                               phy->io_lpcpd);
 260 }
 261
 262 /*
 263  * st33zp24_i2c_remove remove the TPM device
 264  * @param: client, the i2c_client description (TPM I2C description).
 265  * @return: 0 in case of success.
 266  */
 267 static int st33zp24_i2c_remove(struct i2c_client *client)
 268 {
 269         struct tpm_chip *chip = i2c_get_clientdata(client);
 270         int ret;
 271
 272         ret = st33zp24_remove(chip);
 273         if (ret)
 274                 return ret;
 275
 276         return 0;
 277 }
 278
 279 static const struct i2c_device_id st33zp24_i2c_id[] = {
 280         {TPM_ST33_I2C, 0},
 281         {}
 282 };
 283 MODULE_DEVICE_TABLE(i2c, st33zp24_i2c_id);
 284
 285 static const struct of_device_id of_st33zp24_i2c_match[] = {
 286         { .compatible = "st,st33zp24-i2c", },
 287         {}
 288 };
 289 MODULE_DEVICE_TABLE(of, of_st33zp24_i2c_match);
 290
 291 static const struct acpi_device_id st33zp24_i2c_acpi_match[] = {
 292         {"SMO3324"},
 293         {}
 294 };
 295 MODULE_DEVICE_TABLE(acpi, st33zp24_i2c_acpi_match);
 296
 297 static SIMPLE_DEV_PM_OPS(st33zp24_i2c_ops, st33zp24_pm_suspend,
 298                          st33zp24_pm_resume);
 299
 300 static struct i2c_driver st33zp24_i2c_driver = {
 301         .driver = {
 302                 .name = TPM_ST33_I2C,
 303                 .pm = &st33zp24_i2c_ops,
 304                 .of_match_table = of_match_ptr(of_st33zp24_i2c_match),
 305                 .acpi_match_table = ACPI_PTR(st33zp24_i2c_acpi_match),
 306         },
 307         .probe = st33zp24_i2c_probe,
 308         .remove = st33zp24_i2c_remove,
 309         .id_table = st33zp24_i2c_id
 310 };
 311
 312 module_i2c_driver(st33zp24_i2c_driver);
 313
 314 MODULE_AUTHOR("TPM support (TPMsupport@list.st.com)");
 315 MODULE_DESCRIPTION("STM TPM 1.2 I2C ST33 Driver");
 316 MODULE_VERSION("1.3.0");
 317 MODULE_LICENSE("GPL");