WIP FPC-III support
[linux/fpc-iii.git] / drivers / gpu / drm / bridge / synopsys / dw-mipi-dsi.c
blob6b268f9445b36aea903d13fdd8c76822d50c66dc
1 // SPDX-License-Identifier: GPL-2.0+
2 /*
3 * Copyright (c) 2016, Fuzhou Rockchip Electronics Co., Ltd
4 * Copyright (C) STMicroelectronics SA 2017
6 * Modified by Philippe Cornu <philippe.cornu@st.com>
7 * This generic Synopsys DesignWare MIPI DSI host driver is based on the
8 * Rockchip version from rockchip/dw-mipi-dsi.c with phy & bridge APIs.
9 */
11 #include <linux/clk.h>
12 #include <linux/component.h>
13 #include <linux/debugfs.h>
14 #include <linux/iopoll.h>
15 #include <linux/module.h>
16 #include <linux/of_device.h>
17 #include <linux/pm_runtime.h>
18 #include <linux/reset.h>
20 #include <video/mipi_display.h>
22 #include <drm/bridge/dw_mipi_dsi.h>
23 #include <drm/drm_atomic_helper.h>
24 #include <drm/drm_bridge.h>
25 #include <drm/drm_crtc.h>
26 #include <drm/drm_mipi_dsi.h>
27 #include <drm/drm_modes.h>
28 #include <drm/drm_of.h>
29 #include <drm/drm_print.h>
31 #define HWVER_131 0x31333100 /* IP version 1.31 */
33 #define DSI_VERSION 0x00
34 #define VERSION GENMASK(31, 8)
36 #define DSI_PWR_UP 0x04
37 #define RESET 0
38 #define POWERUP BIT(0)
40 #define DSI_CLKMGR_CFG 0x08
41 #define TO_CLK_DIVISION(div) (((div) & 0xff) << 8)
42 #define TX_ESC_CLK_DIVISION(div) ((div) & 0xff)
44 #define DSI_DPI_VCID 0x0c
45 #define DPI_VCID(vcid) ((vcid) & 0x3)
47 #define DSI_DPI_COLOR_CODING 0x10
48 #define LOOSELY18_EN BIT(8)
49 #define DPI_COLOR_CODING_16BIT_1 0x0
50 #define DPI_COLOR_CODING_16BIT_2 0x1
51 #define DPI_COLOR_CODING_16BIT_3 0x2
52 #define DPI_COLOR_CODING_18BIT_1 0x3
53 #define DPI_COLOR_CODING_18BIT_2 0x4
54 #define DPI_COLOR_CODING_24BIT 0x5
56 #define DSI_DPI_CFG_POL 0x14
57 #define COLORM_ACTIVE_LOW BIT(4)
58 #define SHUTD_ACTIVE_LOW BIT(3)
59 #define HSYNC_ACTIVE_LOW BIT(2)
60 #define VSYNC_ACTIVE_LOW BIT(1)
61 #define DATAEN_ACTIVE_LOW BIT(0)
63 #define DSI_DPI_LP_CMD_TIM 0x18
64 #define OUTVACT_LPCMD_TIME(p) (((p) & 0xff) << 16)
65 #define INVACT_LPCMD_TIME(p) ((p) & 0xff)
67 #define DSI_DBI_VCID 0x1c
68 #define DSI_DBI_CFG 0x20
69 #define DSI_DBI_PARTITIONING_EN 0x24
70 #define DSI_DBI_CMDSIZE 0x28
72 #define DSI_PCKHDL_CFG 0x2c
73 #define CRC_RX_EN BIT(4)
74 #define ECC_RX_EN BIT(3)
75 #define BTA_EN BIT(2)
76 #define EOTP_RX_EN BIT(1)
77 #define EOTP_TX_EN BIT(0)
79 #define DSI_GEN_VCID 0x30
81 #define DSI_MODE_CFG 0x34
82 #define ENABLE_VIDEO_MODE 0
83 #define ENABLE_CMD_MODE BIT(0)
85 #define DSI_VID_MODE_CFG 0x38
86 #define ENABLE_LOW_POWER (0x3f << 8)
87 #define ENABLE_LOW_POWER_MASK (0x3f << 8)
88 #define VID_MODE_TYPE_NON_BURST_SYNC_PULSES 0x0
89 #define VID_MODE_TYPE_NON_BURST_SYNC_EVENTS 0x1
90 #define VID_MODE_TYPE_BURST 0x2
91 #define VID_MODE_TYPE_MASK 0x3
92 #define ENABLE_LOW_POWER_CMD BIT(15)
93 #define VID_MODE_VPG_ENABLE BIT(16)
94 #define VID_MODE_VPG_MODE BIT(20)
95 #define VID_MODE_VPG_HORIZONTAL BIT(24)
97 #define DSI_VID_PKT_SIZE 0x3c
98 #define VID_PKT_SIZE(p) ((p) & 0x3fff)
100 #define DSI_VID_NUM_CHUNKS 0x40
101 #define VID_NUM_CHUNKS(c) ((c) & 0x1fff)
103 #define DSI_VID_NULL_SIZE 0x44
104 #define VID_NULL_SIZE(b) ((b) & 0x1fff)
106 #define DSI_VID_HSA_TIME 0x48
107 #define DSI_VID_HBP_TIME 0x4c
108 #define DSI_VID_HLINE_TIME 0x50
109 #define DSI_VID_VSA_LINES 0x54
110 #define DSI_VID_VBP_LINES 0x58
111 #define DSI_VID_VFP_LINES 0x5c
112 #define DSI_VID_VACTIVE_LINES 0x60
113 #define DSI_EDPI_CMD_SIZE 0x64
115 #define DSI_CMD_MODE_CFG 0x68
116 #define MAX_RD_PKT_SIZE_LP BIT(24)
117 #define DCS_LW_TX_LP BIT(19)
118 #define DCS_SR_0P_TX_LP BIT(18)
119 #define DCS_SW_1P_TX_LP BIT(17)
120 #define DCS_SW_0P_TX_LP BIT(16)
121 #define GEN_LW_TX_LP BIT(14)
122 #define GEN_SR_2P_TX_LP BIT(13)
123 #define GEN_SR_1P_TX_LP BIT(12)
124 #define GEN_SR_0P_TX_LP BIT(11)
125 #define GEN_SW_2P_TX_LP BIT(10)
126 #define GEN_SW_1P_TX_LP BIT(9)
127 #define GEN_SW_0P_TX_LP BIT(8)
128 #define ACK_RQST_EN BIT(1)
129 #define TEAR_FX_EN BIT(0)
131 #define CMD_MODE_ALL_LP (MAX_RD_PKT_SIZE_LP | \
132 DCS_LW_TX_LP | \
133 DCS_SR_0P_TX_LP | \
134 DCS_SW_1P_TX_LP | \
135 DCS_SW_0P_TX_LP | \
136 GEN_LW_TX_LP | \
137 GEN_SR_2P_TX_LP | \
138 GEN_SR_1P_TX_LP | \
139 GEN_SR_0P_TX_LP | \
140 GEN_SW_2P_TX_LP | \
141 GEN_SW_1P_TX_LP | \
142 GEN_SW_0P_TX_LP)
144 #define DSI_GEN_HDR 0x6c
145 #define DSI_GEN_PLD_DATA 0x70
147 #define DSI_CMD_PKT_STATUS 0x74
148 #define GEN_RD_CMD_BUSY BIT(6)
149 #define GEN_PLD_R_FULL BIT(5)
150 #define GEN_PLD_R_EMPTY BIT(4)
151 #define GEN_PLD_W_FULL BIT(3)
152 #define GEN_PLD_W_EMPTY BIT(2)
153 #define GEN_CMD_FULL BIT(1)
154 #define GEN_CMD_EMPTY BIT(0)
156 #define DSI_TO_CNT_CFG 0x78
157 #define HSTX_TO_CNT(p) (((p) & 0xffff) << 16)
158 #define LPRX_TO_CNT(p) ((p) & 0xffff)
160 #define DSI_HS_RD_TO_CNT 0x7c
161 #define DSI_LP_RD_TO_CNT 0x80
162 #define DSI_HS_WR_TO_CNT 0x84
163 #define DSI_LP_WR_TO_CNT 0x88
164 #define DSI_BTA_TO_CNT 0x8c
166 #define DSI_LPCLK_CTRL 0x94
167 #define AUTO_CLKLANE_CTRL BIT(1)
168 #define PHY_TXREQUESTCLKHS BIT(0)
170 #define DSI_PHY_TMR_LPCLK_CFG 0x98
171 #define PHY_CLKHS2LP_TIME(lbcc) (((lbcc) & 0x3ff) << 16)
172 #define PHY_CLKLP2HS_TIME(lbcc) ((lbcc) & 0x3ff)
174 #define DSI_PHY_TMR_CFG 0x9c
175 #define PHY_HS2LP_TIME(lbcc) (((lbcc) & 0xff) << 24)
176 #define PHY_LP2HS_TIME(lbcc) (((lbcc) & 0xff) << 16)
177 #define MAX_RD_TIME(lbcc) ((lbcc) & 0x7fff)
178 #define PHY_HS2LP_TIME_V131(lbcc) (((lbcc) & 0x3ff) << 16)
179 #define PHY_LP2HS_TIME_V131(lbcc) ((lbcc) & 0x3ff)
181 #define DSI_PHY_RSTZ 0xa0
182 #define PHY_DISFORCEPLL 0
183 #define PHY_ENFORCEPLL BIT(3)
184 #define PHY_DISABLECLK 0
185 #define PHY_ENABLECLK BIT(2)
186 #define PHY_RSTZ 0
187 #define PHY_UNRSTZ BIT(1)
188 #define PHY_SHUTDOWNZ 0
189 #define PHY_UNSHUTDOWNZ BIT(0)
191 #define DSI_PHY_IF_CFG 0xa4
192 #define PHY_STOP_WAIT_TIME(cycle) (((cycle) & 0xff) << 8)
193 #define N_LANES(n) (((n) - 1) & 0x3)
195 #define DSI_PHY_ULPS_CTRL 0xa8
196 #define DSI_PHY_TX_TRIGGERS 0xac
198 #define DSI_PHY_STATUS 0xb0
199 #define PHY_STOP_STATE_CLK_LANE BIT(2)
200 #define PHY_LOCK BIT(0)
202 #define DSI_PHY_TST_CTRL0 0xb4
203 #define PHY_TESTCLK BIT(1)
204 #define PHY_UNTESTCLK 0
205 #define PHY_TESTCLR BIT(0)
206 #define PHY_UNTESTCLR 0
208 #define DSI_PHY_TST_CTRL1 0xb8
209 #define PHY_TESTEN BIT(16)
210 #define PHY_UNTESTEN 0
211 #define PHY_TESTDOUT(n) (((n) & 0xff) << 8)
212 #define PHY_TESTDIN(n) ((n) & 0xff)
214 #define DSI_INT_ST0 0xbc
215 #define DSI_INT_ST1 0xc0
216 #define DSI_INT_MSK0 0xc4
217 #define DSI_INT_MSK1 0xc8
219 #define DSI_PHY_TMR_RD_CFG 0xf4
220 #define MAX_RD_TIME_V131(lbcc) ((lbcc) & 0x7fff)
222 #define PHY_STATUS_TIMEOUT_US 10000
223 #define CMD_PKT_STATUS_TIMEOUT_US 20000
225 #ifdef CONFIG_DEBUG_FS
226 #define VPG_DEFS(name, dsi) \
227 ((void __force *)&((*dsi).vpg_defs.name))
229 #define REGISTER(name, mask, dsi) \
230 { #name, VPG_DEFS(name, dsi), mask, dsi }
232 struct debugfs_entries {
233 const char *name;
234 bool *reg;
235 u32 mask;
236 struct dw_mipi_dsi *dsi;
238 #endif /* CONFIG_DEBUG_FS */
240 struct dw_mipi_dsi {
241 struct drm_bridge bridge;
242 struct mipi_dsi_host dsi_host;
243 struct drm_bridge *panel_bridge;
244 struct device *dev;
245 void __iomem *base;
247 struct clk *pclk;
249 unsigned int lane_mbps; /* per lane */
250 u32 channel;
251 u32 lanes;
252 u32 format;
253 unsigned long mode_flags;
255 #ifdef CONFIG_DEBUG_FS
256 struct dentry *debugfs;
257 struct debugfs_entries *debugfs_vpg;
258 struct {
259 bool vpg;
260 bool vpg_horizontal;
261 bool vpg_ber_pattern;
262 } vpg_defs;
263 #endif /* CONFIG_DEBUG_FS */
265 struct dw_mipi_dsi *master; /* dual-dsi master ptr */
266 struct dw_mipi_dsi *slave; /* dual-dsi slave ptr */
268 const struct dw_mipi_dsi_plat_data *plat_data;
272 * Check if either a link to a master or slave is present
274 static inline bool dw_mipi_is_dual_mode(struct dw_mipi_dsi *dsi)
276 return dsi->slave || dsi->master;
280 * The controller should generate 2 frames before
281 * preparing the peripheral.
283 static void dw_mipi_dsi_wait_for_two_frames(const struct drm_display_mode *mode)
285 int refresh, two_frames;
287 refresh = drm_mode_vrefresh(mode);
288 two_frames = DIV_ROUND_UP(MSEC_PER_SEC, refresh) * 2;
289 msleep(two_frames);
292 static inline struct dw_mipi_dsi *host_to_dsi(struct mipi_dsi_host *host)
294 return container_of(host, struct dw_mipi_dsi, dsi_host);
297 static inline struct dw_mipi_dsi *bridge_to_dsi(struct drm_bridge *bridge)
299 return container_of(bridge, struct dw_mipi_dsi, bridge);
302 static inline void dsi_write(struct dw_mipi_dsi *dsi, u32 reg, u32 val)
304 writel(val, dsi->base + reg);
307 static inline u32 dsi_read(struct dw_mipi_dsi *dsi, u32 reg)
309 return readl(dsi->base + reg);
312 static int dw_mipi_dsi_host_attach(struct mipi_dsi_host *host,
313 struct mipi_dsi_device *device)
315 struct dw_mipi_dsi *dsi = host_to_dsi(host);
316 const struct dw_mipi_dsi_plat_data *pdata = dsi->plat_data;
317 struct drm_bridge *bridge;
318 struct drm_panel *panel;
319 int ret;
321 if (device->lanes > dsi->plat_data->max_data_lanes) {
322 dev_err(dsi->dev, "the number of data lanes(%u) is too many\n",
323 device->lanes);
324 return -EINVAL;
327 dsi->lanes = device->lanes;
328 dsi->channel = device->channel;
329 dsi->format = device->format;
330 dsi->mode_flags = device->mode_flags;
332 ret = drm_of_find_panel_or_bridge(host->dev->of_node, 1, 0,
333 &panel, &bridge);
334 if (ret)
335 return ret;
337 if (panel) {
338 bridge = drm_panel_bridge_add_typed(panel,
339 DRM_MODE_CONNECTOR_DSI);
340 if (IS_ERR(bridge))
341 return PTR_ERR(bridge);
344 dsi->panel_bridge = bridge;
346 drm_bridge_add(&dsi->bridge);
348 if (pdata->host_ops && pdata->host_ops->attach) {
349 ret = pdata->host_ops->attach(pdata->priv_data, device);
350 if (ret < 0)
351 return ret;
354 return 0;
357 static int dw_mipi_dsi_host_detach(struct mipi_dsi_host *host,
358 struct mipi_dsi_device *device)
360 struct dw_mipi_dsi *dsi = host_to_dsi(host);
361 const struct dw_mipi_dsi_plat_data *pdata = dsi->plat_data;
362 int ret;
364 if (pdata->host_ops && pdata->host_ops->detach) {
365 ret = pdata->host_ops->detach(pdata->priv_data, device);
366 if (ret < 0)
367 return ret;
370 drm_of_panel_bridge_remove(host->dev->of_node, 1, 0);
372 drm_bridge_remove(&dsi->bridge);
374 return 0;
377 static void dw_mipi_message_config(struct dw_mipi_dsi *dsi,
378 const struct mipi_dsi_msg *msg)
380 bool lpm = msg->flags & MIPI_DSI_MSG_USE_LPM;
381 u32 val = 0;
384 * TODO dw drv improvements
385 * largest packet sizes during hfp or during vsa/vpb/vfp
386 * should be computed according to byte lane, lane number and only
387 * if sending lp cmds in high speed is enable (PHY_TXREQUESTCLKHS)
389 dsi_write(dsi, DSI_DPI_LP_CMD_TIM, OUTVACT_LPCMD_TIME(16)
390 | INVACT_LPCMD_TIME(4));
392 if (msg->flags & MIPI_DSI_MSG_REQ_ACK)
393 val |= ACK_RQST_EN;
394 if (lpm)
395 val |= CMD_MODE_ALL_LP;
397 dsi_write(dsi, DSI_CMD_MODE_CFG, val);
399 val = dsi_read(dsi, DSI_VID_MODE_CFG);
400 if (lpm)
401 val |= ENABLE_LOW_POWER_CMD;
402 else
403 val &= ~ENABLE_LOW_POWER_CMD;
404 dsi_write(dsi, DSI_VID_MODE_CFG, val);
407 static int dw_mipi_dsi_gen_pkt_hdr_write(struct dw_mipi_dsi *dsi, u32 hdr_val)
409 int ret;
410 u32 val, mask;
412 ret = readl_poll_timeout(dsi->base + DSI_CMD_PKT_STATUS,
413 val, !(val & GEN_CMD_FULL), 1000,
414 CMD_PKT_STATUS_TIMEOUT_US);
415 if (ret) {
416 dev_err(dsi->dev, "failed to get available command FIFO\n");
417 return ret;
420 dsi_write(dsi, DSI_GEN_HDR, hdr_val);
422 mask = GEN_CMD_EMPTY | GEN_PLD_W_EMPTY;
423 ret = readl_poll_timeout(dsi->base + DSI_CMD_PKT_STATUS,
424 val, (val & mask) == mask,
425 1000, CMD_PKT_STATUS_TIMEOUT_US);
426 if (ret) {
427 dev_err(dsi->dev, "failed to write command FIFO\n");
428 return ret;
431 return 0;
434 static int dw_mipi_dsi_write(struct dw_mipi_dsi *dsi,
435 const struct mipi_dsi_packet *packet)
437 const u8 *tx_buf = packet->payload;
438 int len = packet->payload_length, pld_data_bytes = sizeof(u32), ret;
439 __le32 word;
440 u32 val;
442 while (len) {
443 if (len < pld_data_bytes) {
444 word = 0;
445 memcpy(&word, tx_buf, len);
446 dsi_write(dsi, DSI_GEN_PLD_DATA, le32_to_cpu(word));
447 len = 0;
448 } else {
449 memcpy(&word, tx_buf, pld_data_bytes);
450 dsi_write(dsi, DSI_GEN_PLD_DATA, le32_to_cpu(word));
451 tx_buf += pld_data_bytes;
452 len -= pld_data_bytes;
455 ret = readl_poll_timeout(dsi->base + DSI_CMD_PKT_STATUS,
456 val, !(val & GEN_PLD_W_FULL), 1000,
457 CMD_PKT_STATUS_TIMEOUT_US);
458 if (ret) {
459 dev_err(dsi->dev,
460 "failed to get available write payload FIFO\n");
461 return ret;
465 word = 0;
466 memcpy(&word, packet->header, sizeof(packet->header));
467 return dw_mipi_dsi_gen_pkt_hdr_write(dsi, le32_to_cpu(word));
470 static int dw_mipi_dsi_read(struct dw_mipi_dsi *dsi,
471 const struct mipi_dsi_msg *msg)
473 int i, j, ret, len = msg->rx_len;
474 u8 *buf = msg->rx_buf;
475 u32 val;
477 /* Wait end of the read operation */
478 ret = readl_poll_timeout(dsi->base + DSI_CMD_PKT_STATUS,
479 val, !(val & GEN_RD_CMD_BUSY),
480 1000, CMD_PKT_STATUS_TIMEOUT_US);
481 if (ret) {
482 dev_err(dsi->dev, "Timeout during read operation\n");
483 return ret;
486 for (i = 0; i < len; i += 4) {
487 /* Read fifo must not be empty before all bytes are read */
488 ret = readl_poll_timeout(dsi->base + DSI_CMD_PKT_STATUS,
489 val, !(val & GEN_PLD_R_EMPTY),
490 1000, CMD_PKT_STATUS_TIMEOUT_US);
491 if (ret) {
492 dev_err(dsi->dev, "Read payload FIFO is empty\n");
493 return ret;
496 val = dsi_read(dsi, DSI_GEN_PLD_DATA);
497 for (j = 0; j < 4 && j + i < len; j++)
498 buf[i + j] = val >> (8 * j);
501 return ret;
504 static ssize_t dw_mipi_dsi_host_transfer(struct mipi_dsi_host *host,
505 const struct mipi_dsi_msg *msg)
507 struct dw_mipi_dsi *dsi = host_to_dsi(host);
508 struct mipi_dsi_packet packet;
509 int ret, nb_bytes;
511 ret = mipi_dsi_create_packet(&packet, msg);
512 if (ret) {
513 dev_err(dsi->dev, "failed to create packet: %d\n", ret);
514 return ret;
517 dw_mipi_message_config(dsi, msg);
518 if (dsi->slave)
519 dw_mipi_message_config(dsi->slave, msg);
521 ret = dw_mipi_dsi_write(dsi, &packet);
522 if (ret)
523 return ret;
524 if (dsi->slave) {
525 ret = dw_mipi_dsi_write(dsi->slave, &packet);
526 if (ret)
527 return ret;
530 if (msg->rx_buf && msg->rx_len) {
531 ret = dw_mipi_dsi_read(dsi, msg);
532 if (ret)
533 return ret;
534 nb_bytes = msg->rx_len;
535 } else {
536 nb_bytes = packet.size;
539 return nb_bytes;
542 static const struct mipi_dsi_host_ops dw_mipi_dsi_host_ops = {
543 .attach = dw_mipi_dsi_host_attach,
544 .detach = dw_mipi_dsi_host_detach,
545 .transfer = dw_mipi_dsi_host_transfer,
548 static void dw_mipi_dsi_video_mode_config(struct dw_mipi_dsi *dsi)
550 u32 val;
553 * TODO dw drv improvements
554 * enabling low power is panel-dependent, we should use the
555 * panel configuration here...
557 val = ENABLE_LOW_POWER;
559 if (dsi->mode_flags & MIPI_DSI_MODE_VIDEO_BURST)
560 val |= VID_MODE_TYPE_BURST;
561 else if (dsi->mode_flags & MIPI_DSI_MODE_VIDEO_SYNC_PULSE)
562 val |= VID_MODE_TYPE_NON_BURST_SYNC_PULSES;
563 else
564 val |= VID_MODE_TYPE_NON_BURST_SYNC_EVENTS;
566 #ifdef CONFIG_DEBUG_FS
567 if (dsi->vpg_defs.vpg) {
568 val |= VID_MODE_VPG_ENABLE;
569 val |= dsi->vpg_defs.vpg_horizontal ?
570 VID_MODE_VPG_HORIZONTAL : 0;
571 val |= dsi->vpg_defs.vpg_ber_pattern ? VID_MODE_VPG_MODE : 0;
573 #endif /* CONFIG_DEBUG_FS */
575 dsi_write(dsi, DSI_VID_MODE_CFG, val);
578 static void dw_mipi_dsi_set_mode(struct dw_mipi_dsi *dsi,
579 unsigned long mode_flags)
581 u32 val;
583 dsi_write(dsi, DSI_PWR_UP, RESET);
585 if (mode_flags & MIPI_DSI_MODE_VIDEO) {
586 dsi_write(dsi, DSI_MODE_CFG, ENABLE_VIDEO_MODE);
587 dw_mipi_dsi_video_mode_config(dsi);
588 } else {
589 dsi_write(dsi, DSI_MODE_CFG, ENABLE_CMD_MODE);
592 val = PHY_TXREQUESTCLKHS;
593 if (dsi->mode_flags & MIPI_DSI_CLOCK_NON_CONTINUOUS)
594 val |= AUTO_CLKLANE_CTRL;
595 dsi_write(dsi, DSI_LPCLK_CTRL, val);
597 dsi_write(dsi, DSI_PWR_UP, POWERUP);
600 static void dw_mipi_dsi_disable(struct dw_mipi_dsi *dsi)
602 dsi_write(dsi, DSI_PWR_UP, RESET);
603 dsi_write(dsi, DSI_PHY_RSTZ, PHY_RSTZ);
606 static void dw_mipi_dsi_init(struct dw_mipi_dsi *dsi)
608 const struct dw_mipi_dsi_phy_ops *phy_ops = dsi->plat_data->phy_ops;
609 unsigned int esc_rate; /* in MHz */
610 u32 esc_clk_division;
611 int ret;
614 * The maximum permitted escape clock is 20MHz and it is derived from
615 * lanebyteclk, which is running at "lane_mbps / 8".
617 if (phy_ops->get_esc_clk_rate) {
618 ret = phy_ops->get_esc_clk_rate(dsi->plat_data->priv_data,
619 &esc_rate);
620 if (ret)
621 DRM_DEBUG_DRIVER("Phy get_esc_clk_rate() failed\n");
622 } else
623 esc_rate = 20; /* Default to 20MHz */
626 * We want :
627 * (lane_mbps >> 3) / esc_clk_division < X
628 * which is:
629 * (lane_mbps >> 3) / X > esc_clk_division
631 esc_clk_division = (dsi->lane_mbps >> 3) / esc_rate + 1;
633 dsi_write(dsi, DSI_PWR_UP, RESET);
636 * TODO dw drv improvements
637 * timeout clock division should be computed with the
638 * high speed transmission counter timeout and byte lane...
640 dsi_write(dsi, DSI_CLKMGR_CFG, TO_CLK_DIVISION(10) |
641 TX_ESC_CLK_DIVISION(esc_clk_division));
644 static void dw_mipi_dsi_dpi_config(struct dw_mipi_dsi *dsi,
645 const struct drm_display_mode *mode)
647 u32 val = 0, color = 0;
649 switch (dsi->format) {
650 case MIPI_DSI_FMT_RGB888:
651 color = DPI_COLOR_CODING_24BIT;
652 break;
653 case MIPI_DSI_FMT_RGB666:
654 color = DPI_COLOR_CODING_18BIT_2 | LOOSELY18_EN;
655 break;
656 case MIPI_DSI_FMT_RGB666_PACKED:
657 color = DPI_COLOR_CODING_18BIT_1;
658 break;
659 case MIPI_DSI_FMT_RGB565:
660 color = DPI_COLOR_CODING_16BIT_1;
661 break;
664 if (mode->flags & DRM_MODE_FLAG_NVSYNC)
665 val |= VSYNC_ACTIVE_LOW;
666 if (mode->flags & DRM_MODE_FLAG_NHSYNC)
667 val |= HSYNC_ACTIVE_LOW;
669 dsi_write(dsi, DSI_DPI_VCID, DPI_VCID(dsi->channel));
670 dsi_write(dsi, DSI_DPI_COLOR_CODING, color);
671 dsi_write(dsi, DSI_DPI_CFG_POL, val);
674 static void dw_mipi_dsi_packet_handler_config(struct dw_mipi_dsi *dsi)
676 dsi_write(dsi, DSI_PCKHDL_CFG, CRC_RX_EN | ECC_RX_EN | BTA_EN);
679 static void dw_mipi_dsi_video_packet_config(struct dw_mipi_dsi *dsi,
680 const struct drm_display_mode *mode)
683 * TODO dw drv improvements
684 * only burst mode is supported here. For non-burst video modes,
685 * we should compute DSI_VID_PKT_SIZE, DSI_VCCR.NUMC &
686 * DSI_VNPCR.NPSIZE... especially because this driver supports
687 * non-burst video modes, see dw_mipi_dsi_video_mode_config()...
690 dsi_write(dsi, DSI_VID_PKT_SIZE,
691 dw_mipi_is_dual_mode(dsi) ?
692 VID_PKT_SIZE(mode->hdisplay / 2) :
693 VID_PKT_SIZE(mode->hdisplay));
696 static void dw_mipi_dsi_command_mode_config(struct dw_mipi_dsi *dsi)
699 * TODO dw drv improvements
700 * compute high speed transmission counter timeout according
701 * to the timeout clock division (TO_CLK_DIVISION) and byte lane...
703 dsi_write(dsi, DSI_TO_CNT_CFG, HSTX_TO_CNT(1000) | LPRX_TO_CNT(1000));
705 * TODO dw drv improvements
706 * the Bus-Turn-Around Timeout Counter should be computed
707 * according to byte lane...
709 dsi_write(dsi, DSI_BTA_TO_CNT, 0xd00);
710 dsi_write(dsi, DSI_MODE_CFG, ENABLE_CMD_MODE);
713 /* Get lane byte clock cycles. */
714 static u32 dw_mipi_dsi_get_hcomponent_lbcc(struct dw_mipi_dsi *dsi,
715 const struct drm_display_mode *mode,
716 u32 hcomponent)
718 u32 frac, lbcc;
720 lbcc = hcomponent * dsi->lane_mbps * MSEC_PER_SEC / 8;
722 frac = lbcc % mode->clock;
723 lbcc = lbcc / mode->clock;
724 if (frac)
725 lbcc++;
727 return lbcc;
730 static void dw_mipi_dsi_line_timer_config(struct dw_mipi_dsi *dsi,
731 const struct drm_display_mode *mode)
733 u32 htotal, hsa, hbp, lbcc;
735 htotal = mode->htotal;
736 hsa = mode->hsync_end - mode->hsync_start;
737 hbp = mode->htotal - mode->hsync_end;
740 * TODO dw drv improvements
741 * computations below may be improved...
743 lbcc = dw_mipi_dsi_get_hcomponent_lbcc(dsi, mode, htotal);
744 dsi_write(dsi, DSI_VID_HLINE_TIME, lbcc);
746 lbcc = dw_mipi_dsi_get_hcomponent_lbcc(dsi, mode, hsa);
747 dsi_write(dsi, DSI_VID_HSA_TIME, lbcc);
749 lbcc = dw_mipi_dsi_get_hcomponent_lbcc(dsi, mode, hbp);
750 dsi_write(dsi, DSI_VID_HBP_TIME, lbcc);
753 static void dw_mipi_dsi_vertical_timing_config(struct dw_mipi_dsi *dsi,
754 const struct drm_display_mode *mode)
756 u32 vactive, vsa, vfp, vbp;
758 vactive = mode->vdisplay;
759 vsa = mode->vsync_end - mode->vsync_start;
760 vfp = mode->vsync_start - mode->vdisplay;
761 vbp = mode->vtotal - mode->vsync_end;
763 dsi_write(dsi, DSI_VID_VACTIVE_LINES, vactive);
764 dsi_write(dsi, DSI_VID_VSA_LINES, vsa);
765 dsi_write(dsi, DSI_VID_VFP_LINES, vfp);
766 dsi_write(dsi, DSI_VID_VBP_LINES, vbp);
769 static void dw_mipi_dsi_dphy_timing_config(struct dw_mipi_dsi *dsi)
771 const struct dw_mipi_dsi_phy_ops *phy_ops = dsi->plat_data->phy_ops;
772 struct dw_mipi_dsi_dphy_timing timing;
773 u32 hw_version;
774 int ret;
776 ret = phy_ops->get_timing(dsi->plat_data->priv_data,
777 dsi->lane_mbps, &timing);
778 if (ret)
779 DRM_DEV_ERROR(dsi->dev, "Retrieving phy timings failed\n");
782 * TODO dw drv improvements
783 * data & clock lane timers should be computed according to panel
784 * blankings and to the automatic clock lane control mode...
785 * note: DSI_PHY_TMR_CFG.MAX_RD_TIME should be in line with
786 * DSI_CMD_MODE_CFG.MAX_RD_PKT_SIZE_LP (see CMD_MODE_ALL_LP)
789 hw_version = dsi_read(dsi, DSI_VERSION) & VERSION;
791 if (hw_version >= HWVER_131) {
792 dsi_write(dsi, DSI_PHY_TMR_CFG,
793 PHY_HS2LP_TIME_V131(timing.data_hs2lp) |
794 PHY_LP2HS_TIME_V131(timing.data_lp2hs));
795 dsi_write(dsi, DSI_PHY_TMR_RD_CFG, MAX_RD_TIME_V131(10000));
796 } else {
797 dsi_write(dsi, DSI_PHY_TMR_CFG,
798 PHY_HS2LP_TIME(timing.data_hs2lp) |
799 PHY_LP2HS_TIME(timing.data_lp2hs) |
800 MAX_RD_TIME(10000));
803 dsi_write(dsi, DSI_PHY_TMR_LPCLK_CFG,
804 PHY_CLKHS2LP_TIME(timing.clk_hs2lp) |
805 PHY_CLKLP2HS_TIME(timing.clk_lp2hs));
808 static void dw_mipi_dsi_dphy_interface_config(struct dw_mipi_dsi *dsi)
811 * TODO dw drv improvements
812 * stop wait time should be the maximum between host dsi
813 * and panel stop wait times
815 dsi_write(dsi, DSI_PHY_IF_CFG, PHY_STOP_WAIT_TIME(0x20) |
816 N_LANES(dsi->lanes));
819 static void dw_mipi_dsi_dphy_init(struct dw_mipi_dsi *dsi)
821 /* Clear PHY state */
822 dsi_write(dsi, DSI_PHY_RSTZ, PHY_DISFORCEPLL | PHY_DISABLECLK
823 | PHY_RSTZ | PHY_SHUTDOWNZ);
824 dsi_write(dsi, DSI_PHY_TST_CTRL0, PHY_UNTESTCLR);
825 dsi_write(dsi, DSI_PHY_TST_CTRL0, PHY_TESTCLR);
826 dsi_write(dsi, DSI_PHY_TST_CTRL0, PHY_UNTESTCLR);
829 static void dw_mipi_dsi_dphy_enable(struct dw_mipi_dsi *dsi)
831 u32 val;
832 int ret;
834 dsi_write(dsi, DSI_PHY_RSTZ, PHY_ENFORCEPLL | PHY_ENABLECLK |
835 PHY_UNRSTZ | PHY_UNSHUTDOWNZ);
837 ret = readl_poll_timeout(dsi->base + DSI_PHY_STATUS, val,
838 val & PHY_LOCK, 1000, PHY_STATUS_TIMEOUT_US);
839 if (ret)
840 DRM_DEBUG_DRIVER("failed to wait phy lock state\n");
842 ret = readl_poll_timeout(dsi->base + DSI_PHY_STATUS,
843 val, val & PHY_STOP_STATE_CLK_LANE, 1000,
844 PHY_STATUS_TIMEOUT_US);
845 if (ret)
846 DRM_DEBUG_DRIVER("failed to wait phy clk lane stop state\n");
849 static void dw_mipi_dsi_clear_err(struct dw_mipi_dsi *dsi)
851 dsi_read(dsi, DSI_INT_ST0);
852 dsi_read(dsi, DSI_INT_ST1);
853 dsi_write(dsi, DSI_INT_MSK0, 0);
854 dsi_write(dsi, DSI_INT_MSK1, 0);
857 static void dw_mipi_dsi_bridge_post_disable(struct drm_bridge *bridge)
859 struct dw_mipi_dsi *dsi = bridge_to_dsi(bridge);
860 const struct dw_mipi_dsi_phy_ops *phy_ops = dsi->plat_data->phy_ops;
863 * Switch to command mode before panel-bridge post_disable &
864 * panel unprepare.
865 * Note: panel-bridge disable & panel disable has been called
866 * before by the drm framework.
868 dw_mipi_dsi_set_mode(dsi, 0);
871 * TODO Only way found to call panel-bridge post_disable &
872 * panel unprepare before the dsi "final" disable...
873 * This needs to be fixed in the drm_bridge framework and the API
874 * needs to be updated to manage our own call chains...
876 if (dsi->panel_bridge->funcs->post_disable)
877 dsi->panel_bridge->funcs->post_disable(dsi->panel_bridge);
879 if (phy_ops->power_off)
880 phy_ops->power_off(dsi->plat_data->priv_data);
882 if (dsi->slave) {
883 dw_mipi_dsi_disable(dsi->slave);
884 clk_disable_unprepare(dsi->slave->pclk);
885 pm_runtime_put(dsi->slave->dev);
887 dw_mipi_dsi_disable(dsi);
889 clk_disable_unprepare(dsi->pclk);
890 pm_runtime_put(dsi->dev);
893 static unsigned int dw_mipi_dsi_get_lanes(struct dw_mipi_dsi *dsi)
895 /* this instance is the slave, so add the master's lanes */
896 if (dsi->master)
897 return dsi->master->lanes + dsi->lanes;
899 /* this instance is the master, so add the slave's lanes */
900 if (dsi->slave)
901 return dsi->lanes + dsi->slave->lanes;
903 /* single-dsi, so no other instance to consider */
904 return dsi->lanes;
907 static void dw_mipi_dsi_mode_set(struct dw_mipi_dsi *dsi,
908 const struct drm_display_mode *adjusted_mode)
910 const struct dw_mipi_dsi_phy_ops *phy_ops = dsi->plat_data->phy_ops;
911 void *priv_data = dsi->plat_data->priv_data;
912 int ret;
913 u32 lanes = dw_mipi_dsi_get_lanes(dsi);
915 clk_prepare_enable(dsi->pclk);
917 ret = phy_ops->get_lane_mbps(priv_data, adjusted_mode, dsi->mode_flags,
918 lanes, dsi->format, &dsi->lane_mbps);
919 if (ret)
920 DRM_DEBUG_DRIVER("Phy get_lane_mbps() failed\n");
922 pm_runtime_get_sync(dsi->dev);
923 dw_mipi_dsi_init(dsi);
924 dw_mipi_dsi_dpi_config(dsi, adjusted_mode);
925 dw_mipi_dsi_packet_handler_config(dsi);
926 dw_mipi_dsi_video_mode_config(dsi);
927 dw_mipi_dsi_video_packet_config(dsi, adjusted_mode);
928 dw_mipi_dsi_command_mode_config(dsi);
929 dw_mipi_dsi_line_timer_config(dsi, adjusted_mode);
930 dw_mipi_dsi_vertical_timing_config(dsi, adjusted_mode);
932 dw_mipi_dsi_dphy_init(dsi);
933 dw_mipi_dsi_dphy_timing_config(dsi);
934 dw_mipi_dsi_dphy_interface_config(dsi);
936 dw_mipi_dsi_clear_err(dsi);
938 ret = phy_ops->init(priv_data);
939 if (ret)
940 DRM_DEBUG_DRIVER("Phy init() failed\n");
942 dw_mipi_dsi_dphy_enable(dsi);
944 dw_mipi_dsi_wait_for_two_frames(adjusted_mode);
946 /* Switch to cmd mode for panel-bridge pre_enable & panel prepare */
947 dw_mipi_dsi_set_mode(dsi, 0);
949 if (phy_ops->power_on)
950 phy_ops->power_on(dsi->plat_data->priv_data);
953 static void dw_mipi_dsi_bridge_mode_set(struct drm_bridge *bridge,
954 const struct drm_display_mode *mode,
955 const struct drm_display_mode *adjusted_mode)
957 struct dw_mipi_dsi *dsi = bridge_to_dsi(bridge);
959 dw_mipi_dsi_mode_set(dsi, adjusted_mode);
960 if (dsi->slave)
961 dw_mipi_dsi_mode_set(dsi->slave, adjusted_mode);
964 static void dw_mipi_dsi_bridge_enable(struct drm_bridge *bridge)
966 struct dw_mipi_dsi *dsi = bridge_to_dsi(bridge);
968 /* Switch to video mode for panel-bridge enable & panel enable */
969 dw_mipi_dsi_set_mode(dsi, MIPI_DSI_MODE_VIDEO);
970 if (dsi->slave)
971 dw_mipi_dsi_set_mode(dsi->slave, MIPI_DSI_MODE_VIDEO);
974 static enum drm_mode_status
975 dw_mipi_dsi_bridge_mode_valid(struct drm_bridge *bridge,
976 const struct drm_display_info *info,
977 const struct drm_display_mode *mode)
979 struct dw_mipi_dsi *dsi = bridge_to_dsi(bridge);
980 const struct dw_mipi_dsi_plat_data *pdata = dsi->plat_data;
981 enum drm_mode_status mode_status = MODE_OK;
983 if (pdata->mode_valid)
984 mode_status = pdata->mode_valid(pdata->priv_data, mode);
986 return mode_status;
989 static int dw_mipi_dsi_bridge_attach(struct drm_bridge *bridge,
990 enum drm_bridge_attach_flags flags)
992 struct dw_mipi_dsi *dsi = bridge_to_dsi(bridge);
994 if (!bridge->encoder) {
995 DRM_ERROR("Parent encoder object not found\n");
996 return -ENODEV;
999 /* Set the encoder type as caller does not know it */
1000 bridge->encoder->encoder_type = DRM_MODE_ENCODER_DSI;
1002 /* Attach the panel-bridge to the dsi bridge */
1003 return drm_bridge_attach(bridge->encoder, dsi->panel_bridge, bridge,
1004 flags);
1007 static const struct drm_bridge_funcs dw_mipi_dsi_bridge_funcs = {
1008 .mode_set = dw_mipi_dsi_bridge_mode_set,
1009 .enable = dw_mipi_dsi_bridge_enable,
1010 .post_disable = dw_mipi_dsi_bridge_post_disable,
1011 .mode_valid = dw_mipi_dsi_bridge_mode_valid,
1012 .attach = dw_mipi_dsi_bridge_attach,
1015 #ifdef CONFIG_DEBUG_FS
1017 static int dw_mipi_dsi_debugfs_write(void *data, u64 val)
1019 struct debugfs_entries *vpg = data;
1020 struct dw_mipi_dsi *dsi;
1021 u32 mode_cfg;
1023 if (!vpg)
1024 return -ENODEV;
1026 dsi = vpg->dsi;
1028 *vpg->reg = (bool)val;
1030 mode_cfg = dsi_read(dsi, DSI_VID_MODE_CFG);
1032 if (*vpg->reg)
1033 mode_cfg |= vpg->mask;
1034 else
1035 mode_cfg &= ~vpg->mask;
1037 dsi_write(dsi, DSI_VID_MODE_CFG, mode_cfg);
1039 return 0;
1042 static int dw_mipi_dsi_debugfs_show(void *data, u64 *val)
1044 struct debugfs_entries *vpg = data;
1046 if (!vpg)
1047 return -ENODEV;
1049 *val = *vpg->reg;
1051 return 0;
1054 DEFINE_DEBUGFS_ATTRIBUTE(fops_x32, dw_mipi_dsi_debugfs_show,
1055 dw_mipi_dsi_debugfs_write, "%llu\n");
1057 static void debugfs_create_files(void *data)
1059 struct dw_mipi_dsi *dsi = data;
1060 struct debugfs_entries debugfs[] = {
1061 REGISTER(vpg, VID_MODE_VPG_ENABLE, dsi),
1062 REGISTER(vpg_horizontal, VID_MODE_VPG_HORIZONTAL, dsi),
1063 REGISTER(vpg_ber_pattern, VID_MODE_VPG_MODE, dsi),
1065 int i;
1067 dsi->debugfs_vpg = kmemdup(debugfs, sizeof(debugfs), GFP_KERNEL);
1068 if (!dsi->debugfs_vpg)
1069 return;
1071 for (i = 0; i < ARRAY_SIZE(debugfs); i++)
1072 debugfs_create_file(dsi->debugfs_vpg[i].name, 0644,
1073 dsi->debugfs, &dsi->debugfs_vpg[i],
1074 &fops_x32);
1077 static void dw_mipi_dsi_debugfs_init(struct dw_mipi_dsi *dsi)
1079 dsi->debugfs = debugfs_create_dir(dev_name(dsi->dev), NULL);
1080 if (IS_ERR(dsi->debugfs)) {
1081 dev_err(dsi->dev, "failed to create debugfs root\n");
1082 return;
1085 debugfs_create_files(dsi);
1088 static void dw_mipi_dsi_debugfs_remove(struct dw_mipi_dsi *dsi)
1090 debugfs_remove_recursive(dsi->debugfs);
1091 kfree(dsi->debugfs_vpg);
1094 #else
1096 static void dw_mipi_dsi_debugfs_init(struct dw_mipi_dsi *dsi) { }
1097 static void dw_mipi_dsi_debugfs_remove(struct dw_mipi_dsi *dsi) { }
1099 #endif /* CONFIG_DEBUG_FS */
1101 static struct dw_mipi_dsi *
1102 __dw_mipi_dsi_probe(struct platform_device *pdev,
1103 const struct dw_mipi_dsi_plat_data *plat_data)
1105 struct device *dev = &pdev->dev;
1106 struct reset_control *apb_rst;
1107 struct dw_mipi_dsi *dsi;
1108 int ret;
1110 dsi = devm_kzalloc(dev, sizeof(*dsi), GFP_KERNEL);
1111 if (!dsi)
1112 return ERR_PTR(-ENOMEM);
1114 dsi->dev = dev;
1115 dsi->plat_data = plat_data;
1117 if (!plat_data->phy_ops->init || !plat_data->phy_ops->get_lane_mbps ||
1118 !plat_data->phy_ops->get_timing) {
1119 DRM_ERROR("Phy not properly configured\n");
1120 return ERR_PTR(-ENODEV);
1123 if (!plat_data->base) {
1124 dsi->base = devm_platform_ioremap_resource(pdev, 0);
1125 if (IS_ERR(dsi->base))
1126 return ERR_PTR(-ENODEV);
1128 } else {
1129 dsi->base = plat_data->base;
1132 dsi->pclk = devm_clk_get(dev, "pclk");
1133 if (IS_ERR(dsi->pclk)) {
1134 ret = PTR_ERR(dsi->pclk);
1135 dev_err(dev, "Unable to get pclk: %d\n", ret);
1136 return ERR_PTR(ret);
1140 * Note that the reset was not defined in the initial device tree, so
1141 * we have to be prepared for it not being found.
1143 apb_rst = devm_reset_control_get_optional_exclusive(dev, "apb");
1144 if (IS_ERR(apb_rst)) {
1145 ret = PTR_ERR(apb_rst);
1147 if (ret != -EPROBE_DEFER)
1148 dev_err(dev, "Unable to get reset control: %d\n", ret);
1150 return ERR_PTR(ret);
1153 if (apb_rst) {
1154 ret = clk_prepare_enable(dsi->pclk);
1155 if (ret) {
1156 dev_err(dev, "%s: Failed to enable pclk\n", __func__);
1157 return ERR_PTR(ret);
1160 reset_control_assert(apb_rst);
1161 usleep_range(10, 20);
1162 reset_control_deassert(apb_rst);
1164 clk_disable_unprepare(dsi->pclk);
1167 dw_mipi_dsi_debugfs_init(dsi);
1168 pm_runtime_enable(dev);
1170 dsi->dsi_host.ops = &dw_mipi_dsi_host_ops;
1171 dsi->dsi_host.dev = dev;
1172 ret = mipi_dsi_host_register(&dsi->dsi_host);
1173 if (ret) {
1174 dev_err(dev, "Failed to register MIPI host: %d\n", ret);
1175 dw_mipi_dsi_debugfs_remove(dsi);
1176 return ERR_PTR(ret);
1179 dsi->bridge.driver_private = dsi;
1180 dsi->bridge.funcs = &dw_mipi_dsi_bridge_funcs;
1181 #ifdef CONFIG_OF
1182 dsi->bridge.of_node = pdev->dev.of_node;
1183 #endif
1185 return dsi;
1188 static void __dw_mipi_dsi_remove(struct dw_mipi_dsi *dsi)
1190 mipi_dsi_host_unregister(&dsi->dsi_host);
1192 pm_runtime_disable(dsi->dev);
1193 dw_mipi_dsi_debugfs_remove(dsi);
1196 void dw_mipi_dsi_set_slave(struct dw_mipi_dsi *dsi, struct dw_mipi_dsi *slave)
1198 /* introduce controllers to each other */
1199 dsi->slave = slave;
1200 dsi->slave->master = dsi;
1202 /* migrate settings for already attached displays */
1203 dsi->slave->lanes = dsi->lanes;
1204 dsi->slave->channel = dsi->channel;
1205 dsi->slave->format = dsi->format;
1206 dsi->slave->mode_flags = dsi->mode_flags;
1208 EXPORT_SYMBOL_GPL(dw_mipi_dsi_set_slave);
1211 * Probe/remove API, used from platforms based on the DRM bridge API.
1213 struct dw_mipi_dsi *
1214 dw_mipi_dsi_probe(struct platform_device *pdev,
1215 const struct dw_mipi_dsi_plat_data *plat_data)
1217 return __dw_mipi_dsi_probe(pdev, plat_data);
1219 EXPORT_SYMBOL_GPL(dw_mipi_dsi_probe);
1221 void dw_mipi_dsi_remove(struct dw_mipi_dsi *dsi)
1223 __dw_mipi_dsi_remove(dsi);
1225 EXPORT_SYMBOL_GPL(dw_mipi_dsi_remove);
1228 * Bind/unbind API, used from platforms based on the component framework.
1230 int dw_mipi_dsi_bind(struct dw_mipi_dsi *dsi, struct drm_encoder *encoder)
1232 int ret;
1234 ret = drm_bridge_attach(encoder, &dsi->bridge, NULL, 0);
1235 if (ret) {
1236 DRM_ERROR("Failed to initialize bridge with drm\n");
1237 return ret;
1240 return ret;
1242 EXPORT_SYMBOL_GPL(dw_mipi_dsi_bind);
1244 void dw_mipi_dsi_unbind(struct dw_mipi_dsi *dsi)
1247 EXPORT_SYMBOL_GPL(dw_mipi_dsi_unbind);
1249 MODULE_AUTHOR("Chris Zhong <zyw@rock-chips.com>");
1250 MODULE_AUTHOR("Philippe Cornu <philippe.cornu@st.com>");
1251 MODULE_DESCRIPTION("DW MIPI DSI host controller driver");
1252 MODULE_LICENSE("GPL");
1253 MODULE_ALIAS("platform:dw-mipi-dsi");