WIP FPC-III support

[linux/fpc-iii.git] / drivers / media / platform / omap3isp / ispresizer.c

// SPDX-License-Identifier: GPL-2.0-only
/*
 * ispresizer.c
 *
 * TI OMAP3 ISP - Resizer module
 *
 * Copyright (C) 2010 Nokia Corporation
 * Copyright (C) 2009 Texas Instruments, Inc
 *
 * Contacts: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
 *           Sakari Ailus <sakari.ailus@iki.fi>
 */

#include <linux/device.h>
#include <linux/mm.h>
#include <linux/module.h>

#include "isp.h"
#include "ispreg.h"
#include "ispresizer.h"

/*
 * Resizer Constants
 */
#define MIN_RESIZE_VALUE                64
#define MID_RESIZE_VALUE                512
#define MAX_RESIZE_VALUE                1024

#define MIN_IN_WIDTH                    32
#define MIN_IN_HEIGHT                   32
#define MAX_IN_WIDTH_MEMORY_MODE        4095
#define MAX_IN_WIDTH_ONTHEFLY_MODE_ES1  1280
#define MAX_IN_WIDTH_ONTHEFLY_MODE_ES2  4095
#define MAX_IN_HEIGHT                   4095

#define MIN_OUT_WIDTH                   16
#define MIN_OUT_HEIGHT                  2
#define MAX_OUT_HEIGHT                  4095

/*
 * Resizer Use Constraints
 * "TRM ES3.1, table 12-46"
 */
#define MAX_4TAP_OUT_WIDTH_ES1          1280
#define MAX_7TAP_OUT_WIDTH_ES1          640
#define MAX_4TAP_OUT_WIDTH_ES2          3312
#define MAX_7TAP_OUT_WIDTH_ES2          1650
#define MAX_4TAP_OUT_WIDTH_3630         4096
#define MAX_7TAP_OUT_WIDTH_3630         2048

/*
 * Constants for ratio calculation
 */
#define RESIZE_DIVISOR                  256
#define DEFAULT_PHASE                   1

/*
 * Default (and only) configuration of filter coefficients.
 * 7-tap mode is for scale factors 0.25x to 0.5x.
 * 4-tap mode is for scale factors 0.5x to 4.0x.
 * There shouldn't be any reason to recalculate these, EVER.
 */
static const struct isprsz_coef filter_coefs = {
        /* For 8-phase 4-tap horizontal filter: */
        {
                0x0000, 0x0100, 0x0000, 0x0000,
                0x03FA, 0x00F6, 0x0010, 0x0000,
                0x03F9, 0x00DB, 0x002C, 0x0000,
                0x03FB, 0x00B3, 0x0053, 0x03FF,
                0x03FD, 0x0082, 0x0084, 0x03FD,
                0x03FF, 0x0053, 0x00B3, 0x03FB,
                0x0000, 0x002C, 0x00DB, 0x03F9,
                0x0000, 0x0010, 0x00F6, 0x03FA
        },
        /* For 8-phase 4-tap vertical filter: */
        {
                0x0000, 0x0100, 0x0000, 0x0000,
                0x03FA, 0x00F6, 0x0010, 0x0000,
                0x03F9, 0x00DB, 0x002C, 0x0000,
                0x03FB, 0x00B3, 0x0053, 0x03FF,
                0x03FD, 0x0082, 0x0084, 0x03FD,
                0x03FF, 0x0053, 0x00B3, 0x03FB,
                0x0000, 0x002C, 0x00DB, 0x03F9,
                0x0000, 0x0010, 0x00F6, 0x03FA
        },
        /* For 4-phase 7-tap horizontal filter: */
        #define DUMMY 0
        {
                0x0004, 0x0023, 0x005A, 0x0058, 0x0023, 0x0004, 0x0000, DUMMY,
                0x0002, 0x0018, 0x004d, 0x0060, 0x0031, 0x0008, 0x0000, DUMMY,
                0x0001, 0x000f, 0x003f, 0x0062, 0x003f, 0x000f, 0x0001, DUMMY,
                0x0000, 0x0008, 0x0031, 0x0060, 0x004d, 0x0018, 0x0002, DUMMY
        },
        /* For 4-phase 7-tap vertical filter: */
        {
                0x0004, 0x0023, 0x005A, 0x0058, 0x0023, 0x0004, 0x0000, DUMMY,
                0x0002, 0x0018, 0x004d, 0x0060, 0x0031, 0x0008, 0x0000, DUMMY,
                0x0001, 0x000f, 0x003f, 0x0062, 0x003f, 0x000f, 0x0001, DUMMY,
                0x0000, 0x0008, 0x0031, 0x0060, 0x004d, 0x0018, 0x0002, DUMMY
        }
        /*
         * The dummy padding is required in 7-tap mode because of how the
         * registers are arranged physically.
         */
        #undef DUMMY
};

/*
 * __resizer_get_format - helper function for getting resizer format
 * @res   : pointer to resizer private structure
 * @pad   : pad number
 * @cfg: V4L2 subdev pad configuration
 * @which : wanted subdev format
 * return zero
 */
static struct v4l2_mbus_framefmt *
__resizer_get_format(struct isp_res_device *res, struct v4l2_subdev_pad_config *cfg,
                     unsigned int pad, enum v4l2_subdev_format_whence which)
{
        if (which == V4L2_SUBDEV_FORMAT_TRY)
                return v4l2_subdev_get_try_format(&res->subdev, cfg, pad);
        else
                return &res->formats[pad];
}

/*
 * __resizer_get_crop - helper function for getting resizer crop rectangle
 * @res   : pointer to resizer private structure
 * @cfg: V4L2 subdev pad configuration
 * @which : wanted subdev crop rectangle
 */
static struct v4l2_rect *
__resizer_get_crop(struct isp_res_device *res, struct v4l2_subdev_pad_config *cfg,
                   enum v4l2_subdev_format_whence which)
{
        if (which == V4L2_SUBDEV_FORMAT_TRY)
                return v4l2_subdev_get_try_crop(&res->subdev, cfg, RESZ_PAD_SINK);
        else
                return &res->crop.request;
}

/*
 * resizer_set_filters - Set resizer filters
 * @res: Device context.
 * @h_coeff: horizontal coefficient
 * @v_coeff: vertical coefficient
 * Return none
 */
static void resizer_set_filters(struct isp_res_device *res, const u16 *h_coeff,
                                const u16 *v_coeff)
{
        struct isp_device *isp = to_isp_device(res);
        u32 startaddr_h, startaddr_v, tmp_h, tmp_v;
        int i;

        startaddr_h = ISPRSZ_HFILT10;
        startaddr_v = ISPRSZ_VFILT10;

        for (i = 0; i < COEFF_CNT; i += 2) {
                tmp_h = h_coeff[i] |
                        (h_coeff[i + 1] << ISPRSZ_HFILT_COEF1_SHIFT);
                tmp_v = v_coeff[i] |
                        (v_coeff[i + 1] << ISPRSZ_VFILT_COEF1_SHIFT);
                isp_reg_writel(isp, tmp_h, OMAP3_ISP_IOMEM_RESZ, startaddr_h);
                isp_reg_writel(isp, tmp_v, OMAP3_ISP_IOMEM_RESZ, startaddr_v);
                startaddr_h += 4;
                startaddr_v += 4;
        }
}

/*
 * resizer_set_bilinear - Chrominance horizontal algorithm select
 * @res: Device context.
 * @type: Filtering interpolation type.
 *
 * Filtering that is same as luminance processing is
 * intended only for downsampling, and bilinear interpolation
 * is intended only for upsampling.
 */
static void resizer_set_bilinear(struct isp_res_device *res,
                                 enum resizer_chroma_algo type)
{
        struct isp_device *isp = to_isp_device(res);

        if (type == RSZ_BILINEAR)
                isp_reg_set(isp, OMAP3_ISP_IOMEM_RESZ, ISPRSZ_CNT,
                            ISPRSZ_CNT_CBILIN);
        else
                isp_reg_clr(isp, OMAP3_ISP_IOMEM_RESZ, ISPRSZ_CNT,
                            ISPRSZ_CNT_CBILIN);
}

/*
 * resizer_set_ycpos - Luminance and chrominance order
 * @res: Device context.
 * @pixelcode: pixel code.
 */
static void resizer_set_ycpos(struct isp_res_device *res, u32 pixelcode)
{
        struct isp_device *isp = to_isp_device(res);

        switch (pixelcode) {
        case MEDIA_BUS_FMT_YUYV8_1X16:
                isp_reg_set(isp, OMAP3_ISP_IOMEM_RESZ, ISPRSZ_CNT,
                            ISPRSZ_CNT_YCPOS);
                break;
        case MEDIA_BUS_FMT_UYVY8_1X16:
                isp_reg_clr(isp, OMAP3_ISP_IOMEM_RESZ, ISPRSZ_CNT,
                            ISPRSZ_CNT_YCPOS);
                break;
        default:
                return;
        }
}

/*
 * resizer_set_phase - Setup horizontal and vertical starting phase
 * @res: Device context.
 * @h_phase: horizontal phase parameters.
 * @v_phase: vertical phase parameters.
 *
 * Horizontal and vertical phase range is 0 to 7
 */
static void resizer_set_phase(struct isp_res_device *res, u32 h_phase,
                              u32 v_phase)
{
        struct isp_device *isp = to_isp_device(res);
        u32 rgval;

        rgval = isp_reg_readl(isp, OMAP3_ISP_IOMEM_RESZ, ISPRSZ_CNT) &
              ~(ISPRSZ_CNT_HSTPH_MASK | ISPRSZ_CNT_VSTPH_MASK);
        rgval |= (h_phase << ISPRSZ_CNT_HSTPH_SHIFT) & ISPRSZ_CNT_HSTPH_MASK;
        rgval |= (v_phase << ISPRSZ_CNT_VSTPH_SHIFT) & ISPRSZ_CNT_VSTPH_MASK;

        isp_reg_writel(isp, rgval, OMAP3_ISP_IOMEM_RESZ, ISPRSZ_CNT);
}

/*
 * resizer_set_luma - Setup luminance enhancer parameters
 * @res: Device context.
 * @luma: Structure for luminance enhancer parameters.
 *
 * Algorithm select:
 *  0x0: Disable
 *  0x1: [-1  2 -1]/2 high-pass filter
 *  0x2: [-1 -2  6 -2 -1]/4 high-pass filter
 *
 * Maximum gain:
 *  The data is coded in U4Q4 representation.
 *
 * Slope:
 *  The data is coded in U4Q4 representation.
 *
 * Coring offset:
 *  The data is coded in U8Q0 representation.
 *
 * The new luminance value is computed as:
 *  Y += HPF(Y) x max(GAIN, (HPF(Y) - CORE) x SLOP + 8) >> 4.
 */
static void resizer_set_luma(struct isp_res_device *res,
                             struct resizer_luma_yenh *luma)
{
        struct isp_device *isp = to_isp_device(res);
        u32 rgval;

        rgval  = (luma->algo << ISPRSZ_YENH_ALGO_SHIFT)
                  & ISPRSZ_YENH_ALGO_MASK;
        rgval |= (luma->gain << ISPRSZ_YENH_GAIN_SHIFT)
                  & ISPRSZ_YENH_GAIN_MASK;
        rgval |= (luma->slope << ISPRSZ_YENH_SLOP_SHIFT)
                  & ISPRSZ_YENH_SLOP_MASK;
        rgval |= (luma->core << ISPRSZ_YENH_CORE_SHIFT)
                  & ISPRSZ_YENH_CORE_MASK;

        isp_reg_writel(isp, rgval, OMAP3_ISP_IOMEM_RESZ, ISPRSZ_YENH);
}

/*
 * resizer_set_source - Input source select
 * @res: Device context.
 * @source: Input source type
 *
 * If this field is set to RESIZER_INPUT_VP, the resizer input is fed from
 * Preview/CCDC engine, otherwise from memory.
 */
static void resizer_set_source(struct isp_res_device *res,
                               enum resizer_input_entity source)
{
        struct isp_device *isp = to_isp_device(res);

        if (source == RESIZER_INPUT_MEMORY)
                isp_reg_set(isp, OMAP3_ISP_IOMEM_RESZ, ISPRSZ_CNT,
                            ISPRSZ_CNT_INPSRC);
        else
                isp_reg_clr(isp, OMAP3_ISP_IOMEM_RESZ, ISPRSZ_CNT,
                            ISPRSZ_CNT_INPSRC);
}

/*
 * resizer_set_ratio - Setup horizontal and vertical resizing value
 * @res: Device context.
 * @ratio: Structure for ratio parameters.
 *
 * Resizing range from 64 to 1024
 */
static void resizer_set_ratio(struct isp_res_device *res,
                              const struct resizer_ratio *ratio)
{
        struct isp_device *isp = to_isp_device(res);
        const u16 *h_filter, *v_filter;
        u32 rgval;

        rgval = isp_reg_readl(isp, OMAP3_ISP_IOMEM_RESZ, ISPRSZ_CNT) &
                              ~(ISPRSZ_CNT_HRSZ_MASK | ISPRSZ_CNT_VRSZ_MASK);
        rgval |= ((ratio->horz - 1) << ISPRSZ_CNT_HRSZ_SHIFT)
                  & ISPRSZ_CNT_HRSZ_MASK;
        rgval |= ((ratio->vert - 1) << ISPRSZ_CNT_VRSZ_SHIFT)
                  & ISPRSZ_CNT_VRSZ_MASK;
        isp_reg_writel(isp, rgval, OMAP3_ISP_IOMEM_RESZ, ISPRSZ_CNT);

        /* prepare horizontal filter coefficients */
        if (ratio->horz > MID_RESIZE_VALUE)
                h_filter = &filter_coefs.h_filter_coef_7tap[0];
        else
                h_filter = &filter_coefs.h_filter_coef_4tap[0];

        /* prepare vertical filter coefficients */
        if (ratio->vert > MID_RESIZE_VALUE)
                v_filter = &filter_coefs.v_filter_coef_7tap[0];
        else
                v_filter = &filter_coefs.v_filter_coef_4tap[0];

        resizer_set_filters(res, h_filter, v_filter);
}

/*
 * resizer_set_dst_size - Setup the output height and width
 * @res: Device context.
 * @width: Output width.
 * @height: Output height.
 *
 * Width :
 *  The value must be EVEN.
 *
 * Height:
 *  The number of bytes written to SDRAM must be
 *  a multiple of 16-bytes if the vertical resizing factor
 *  is greater than 1x (upsizing)
 */
static void resizer_set_output_size(struct isp_res_device *res,
                                    u32 width, u32 height)
{
        struct isp_device *isp = to_isp_device(res);
        u32 rgval;

        rgval  = (width << ISPRSZ_OUT_SIZE_HORZ_SHIFT)
                 & ISPRSZ_OUT_SIZE_HORZ_MASK;
        rgval |= (height << ISPRSZ_OUT_SIZE_VERT_SHIFT)
                 & ISPRSZ_OUT_SIZE_VERT_MASK;
        isp_reg_writel(isp, rgval, OMAP3_ISP_IOMEM_RESZ, ISPRSZ_OUT_SIZE);
}

/*
 * resizer_set_output_offset - Setup memory offset for the output lines.
 * @res: Device context.
 * @offset: Memory offset.
 *
 * The 5 LSBs are forced to be zeros by the hardware to align on a 32-byte
 * boundary; the 5 LSBs are read-only. For optimal use of SDRAM bandwidth,
 * the SDRAM line offset must be set on a 256-byte boundary
 */
static void resizer_set_output_offset(struct isp_res_device *res, u32 offset)
{
        struct isp_device *isp = to_isp_device(res);

        isp_reg_writel(isp, offset, OMAP3_ISP_IOMEM_RESZ, ISPRSZ_SDR_OUTOFF);
}

/*
 * resizer_set_start - Setup vertical and horizontal start position
 * @res: Device context.
 * @left: Horizontal start position.
 * @top: Vertical start position.
 *
 * Vertical start line:
 *  This field makes sense only when the resizer obtains its input
 *  from the preview engine/CCDC
 *
 * Horizontal start pixel:
 *  Pixels are coded on 16 bits for YUV and 8 bits for color separate data.
 *  When the resizer gets its input from SDRAM, this field must be set
 *  to <= 15 for YUV 16-bit data and <= 31 for 8-bit color separate data
 */
static void resizer_set_start(struct isp_res_device *res, u32 left, u32 top)
{
        struct isp_device *isp = to_isp_device(res);
        u32 rgval;

        rgval = (left << ISPRSZ_IN_START_HORZ_ST_SHIFT)
                & ISPRSZ_IN_START_HORZ_ST_MASK;
        rgval |= (top << ISPRSZ_IN_START_VERT_ST_SHIFT)
                 & ISPRSZ_IN_START_VERT_ST_MASK;

        isp_reg_writel(isp, rgval, OMAP3_ISP_IOMEM_RESZ, ISPRSZ_IN_START);
}

/*
 * resizer_set_input_size - Setup the input size
 * @res: Device context.
 * @width: The range is 0 to 4095 pixels
 * @height: The range is 0 to 4095 lines
 */
static void resizer_set_input_size(struct isp_res_device *res,
                                   u32 width, u32 height)
{
        struct isp_device *isp = to_isp_device(res);
        u32 rgval;

        rgval = (width << ISPRSZ_IN_SIZE_HORZ_SHIFT)
                & ISPRSZ_IN_SIZE_HORZ_MASK;
        rgval |= (height << ISPRSZ_IN_SIZE_VERT_SHIFT)
                 & ISPRSZ_IN_SIZE_VERT_MASK;

        isp_reg_writel(isp, rgval, OMAP3_ISP_IOMEM_RESZ, ISPRSZ_IN_SIZE);
}

/*
 * resizer_set_src_offs - Setup the memory offset for the input lines
 * @res: Device context.
 * @offset: Memory offset.
 *
 * The 5 LSBs are forced to be zeros by the hardware to align on a 32-byte
 * boundary; the 5 LSBs are read-only. This field must be programmed to be
 * 0x0 if the resizer input is from preview engine/CCDC.
 */
static void resizer_set_input_offset(struct isp_res_device *res, u32 offset)
{
        struct isp_device *isp = to_isp_device(res);

        isp_reg_writel(isp, offset, OMAP3_ISP_IOMEM_RESZ, ISPRSZ_SDR_INOFF);
}

/*
 * resizer_set_intype - Input type select
 * @res: Device context.
 * @type: Pixel format type.
 */
static void resizer_set_intype(struct isp_res_device *res,
                               enum resizer_colors_type type)
{
        struct isp_device *isp = to_isp_device(res);

        if (type == RSZ_COLOR8)
                isp_reg_set(isp, OMAP3_ISP_IOMEM_RESZ, ISPRSZ_CNT,
                            ISPRSZ_CNT_INPTYP);
        else
                isp_reg_clr(isp, OMAP3_ISP_IOMEM_RESZ, ISPRSZ_CNT,
                            ISPRSZ_CNT_INPTYP);
}

/*
 * __resizer_set_inaddr - Helper function for set input address
 * @res : pointer to resizer private data structure
 * @addr: input address
 * return none
 */
static void __resizer_set_inaddr(struct isp_res_device *res, u32 addr)
{
        struct isp_device *isp = to_isp_device(res);

        isp_reg_writel(isp, addr, OMAP3_ISP_IOMEM_RESZ, ISPRSZ_SDR_INADD);
}

/*
 * The data rate at the horizontal resizer output must not exceed half the
 * functional clock or 100 MP/s, whichever is lower. According to the TRM
 * there's no similar requirement for the vertical resizer output. However
 * experience showed that vertical upscaling by 4 leads to SBL overflows (with
 * data rates at the resizer output exceeding 300 MP/s). Limiting the resizer
 * output data rate to the functional clock or 200 MP/s, whichever is lower,
 * seems to get rid of SBL overflows.
 *
 * The maximum data rate at the output of the horizontal resizer can thus be
 * computed with
 *
 * max intermediate rate <= L3 clock * input height / output height
 * max intermediate rate <= L3 clock / 2
 *
 * The maximum data rate at the resizer input is then
 *
 * max input rate <= max intermediate rate * input width / output width
 *
 * where the input width and height are the resizer input crop rectangle size.
 * The TRM doesn't clearly explain if that's a maximum instant data rate or a
 * maximum average data rate.
 */
void omap3isp_resizer_max_rate(struct isp_res_device *res,
                               unsigned int *max_rate)
{
        struct isp_pipeline *pipe = to_isp_pipeline(&res->subdev.entity);
        const struct v4l2_mbus_framefmt *ofmt = &res->formats[RESZ_PAD_SOURCE];
        unsigned long limit = min(pipe->l3_ick, 200000000UL);
        unsigned long clock;

        clock = div_u64((u64)limit * res->crop.active.height, ofmt->height);
        clock = min(clock, limit / 2);
        *max_rate = div_u64((u64)clock * res->crop.active.width, ofmt->width);
}

/*
 * When the resizer processes images from memory, the driver must slow down read
 * requests on the input to at least comply with the internal data rate
 * requirements. If the application real-time requirements can cope with slower
 * processing, the resizer can be slowed down even more to put less pressure on
 * the overall system.
 *
 * When the resizer processes images on the fly (either from the CCDC or the
 * preview module), the same data rate requirements apply but they can't be
 * enforced at the resizer level. The image input module (sensor, CCP2 or
 * preview module) must not provide image data faster than the resizer can
 * process.
 *
 * For live image pipelines, the data rate is set by the frame format, size and
 * rate. The sensor output frame rate must not exceed the maximum resizer data
 * rate.
 *
 * The resizer slows down read requests by inserting wait cycles in the SBL
 * requests. The maximum number of 256-byte requests per second can be computed
 * as (the data rate is multiplied by 2 to convert from pixels per second to
 * bytes per second)
 *
 * request per second = data rate * 2 / 256
 * cycles per request = cycles per second / requests per second
 *
 * The number of cycles per second is controlled by the L3 clock, leading to
 *
 * cycles per request = L3 frequency / 2 * 256 / data rate
 */
static void resizer_adjust_bandwidth(struct isp_res_device *res)
{
        struct isp_pipeline *pipe = to_isp_pipeline(&res->subdev.entity);
        struct isp_device *isp = to_isp_device(res);
        unsigned long l3_ick = pipe->l3_ick;
        struct v4l2_fract *timeperframe;
        unsigned int cycles_per_frame;
        unsigned int requests_per_frame;
        unsigned int cycles_per_request;
        unsigned int granularity;
        unsigned int minimum;
        unsigned int maximum;
        unsigned int value;

        if (res->input != RESIZER_INPUT_MEMORY) {
                isp_reg_clr(isp, OMAP3_ISP_IOMEM_SBL, ISPSBL_SDR_REQ_EXP,
                            ISPSBL_SDR_REQ_RSZ_EXP_MASK);
                return;
        }

        switch (isp->revision) {
        case ISP_REVISION_1_0:
        case ISP_REVISION_2_0:
        default:
                granularity = 1024;
                break;

        case ISP_REVISION_15_0:
                granularity = 32;
                break;
        }

        /* Compute the minimum number of cycles per request, based on the
         * pipeline maximum data rate. This is an absolute lower bound if we
         * don't want SBL overflows, so round the value up.
         */
        cycles_per_request = div_u64((u64)l3_ick / 2 * 256 + pipe->max_rate - 1,
                                     pipe->max_rate);
        minimum = DIV_ROUND_UP(cycles_per_request, granularity);

        /* Compute the maximum number of cycles per request, based on the
         * requested frame rate. This is a soft upper bound to achieve a frame
         * rate equal or higher than the requested value, so round the value
         * down.
         */
        timeperframe = &pipe->max_timeperframe;

        requests_per_frame = DIV_ROUND_UP(res->crop.active.width * 2, 256)
                           * res->crop.active.height;
        cycles_per_frame = div_u64((u64)l3_ick * timeperframe->numerator,
                                   timeperframe->denominator);
        cycles_per_request = cycles_per_frame / requests_per_frame;

        maximum = cycles_per_request / granularity;

        value = max(minimum, maximum);

        dev_dbg(isp->dev, "%s: cycles per request = %u\n", __func__, value);
        isp_reg_clr_set(isp, OMAP3_ISP_IOMEM_SBL, ISPSBL_SDR_REQ_EXP,
                        ISPSBL_SDR_REQ_RSZ_EXP_MASK,
                        value << ISPSBL_SDR_REQ_RSZ_EXP_SHIFT);
}

/*
 * omap3isp_resizer_busy - Checks if ISP resizer is busy.
 *
 * Returns busy field from ISPRSZ_PCR register.
 */
int omap3isp_resizer_busy(struct isp_res_device *res)
{
        struct isp_device *isp = to_isp_device(res);

        return isp_reg_readl(isp, OMAP3_ISP_IOMEM_RESZ, ISPRSZ_PCR) &
                             ISPRSZ_PCR_BUSY;
}

/*
 * resizer_set_inaddr - Sets the memory address of the input frame.
 * @addr: 32bit memory address aligned on 32byte boundary.
 */
static void resizer_set_inaddr(struct isp_res_device *res, u32 addr)
{
        res->addr_base = addr;

        /* This will handle crop settings in stream off state */
        if (res->crop_offset)
                addr += res->crop_offset & ~0x1f;

        __resizer_set_inaddr(res, addr);
}

/*
 * Configures the memory address to which the output frame is written.
 * @addr: 32bit memory address aligned on 32byte boundary.
 * Note: For SBL efficiency reasons the address should be on a 256-byte
 * boundary.
 */
static void resizer_set_outaddr(struct isp_res_device *res, u32 addr)
{
        struct isp_device *isp = to_isp_device(res);

        /*
         * Set output address. This needs to be in its own function
         * because it changes often.
         */
        isp_reg_writel(isp, addr << ISPRSZ_SDR_OUTADD_ADDR_SHIFT,
                       OMAP3_ISP_IOMEM_RESZ, ISPRSZ_SDR_OUTADD);
}

/*
 * resizer_print_status - Prints the values of the resizer module registers.
 */
#define RSZ_PRINT_REGISTER(isp, name)\
        dev_dbg(isp->dev, "###RSZ " #name "=0x%08x\n", \
                isp_reg_readl(isp, OMAP3_ISP_IOMEM_RESZ, ISPRSZ_##name))

static void resizer_print_status(struct isp_res_device *res)
{
        struct isp_device *isp = to_isp_device(res);

        dev_dbg(isp->dev, "-------------Resizer Register dump----------\n");

        RSZ_PRINT_REGISTER(isp, PCR);
        RSZ_PRINT_REGISTER(isp, CNT);
        RSZ_PRINT_REGISTER(isp, OUT_SIZE);
        RSZ_PRINT_REGISTER(isp, IN_START);
        RSZ_PRINT_REGISTER(isp, IN_SIZE);
        RSZ_PRINT_REGISTER(isp, SDR_INADD);
        RSZ_PRINT_REGISTER(isp, SDR_INOFF);
        RSZ_PRINT_REGISTER(isp, SDR_OUTADD);
        RSZ_PRINT_REGISTER(isp, SDR_OUTOFF);
        RSZ_PRINT_REGISTER(isp, YENH);

        dev_dbg(isp->dev, "--------------------------------------------\n");
}

/*
 * resizer_calc_ratios - Helper function for calculating resizer ratios
 * @res: pointer to resizer private data structure
 * @input: input frame size
 * @output: output frame size
 * @ratio : return calculated ratios
 * return none
 *
 * The resizer uses a polyphase sample rate converter. The upsampling filter
 * has a fixed number of phases that depend on the resizing ratio. As the ratio
 * computation depends on the number of phases, we need to compute a first
 * approximation and then refine it.
 *
 * The input/output/ratio relationship is given by the OMAP34xx TRM:
 *
 * - 8-phase, 4-tap mode (RSZ = 64 ~ 512)
 *      iw = (32 * sph + (ow - 1) * hrsz + 16) >> 8 + 7
 *      ih = (32 * spv + (oh - 1) * vrsz + 16) >> 8 + 4
 * - 4-phase, 7-tap mode (RSZ = 513 ~ 1024)
 *      iw = (64 * sph + (ow - 1) * hrsz + 32) >> 8 + 7
 *      ih = (64 * spv + (oh - 1) * vrsz + 32) >> 8 + 7
 *
 * iw and ih are the input width and height after cropping. Those equations need
 * to be satisfied exactly for the resizer to work correctly.
 *
 * The equations can't be easily reverted, as the >> 8 operation is not linear.
 * In addition, not all input sizes can be achieved for a given output size. To
 * get the highest input size lower than or equal to the requested input size,
 * we need to compute the highest resizing ratio that satisfies the following
 * inequality (taking the 4-tap mode width equation as an example)
 *
 *      iw >= (32 * sph + (ow - 1) * hrsz + 16) >> 8 - 7
 *
 * (where iw is the requested input width) which can be rewritten as
 *
 *        iw - 7            >= (32 * sph + (ow - 1) * hrsz + 16) >> 8
 *       (iw - 7) << 8      >=  32 * sph + (ow - 1) * hrsz + 16 - b
 *      ((iw - 7) << 8) + b >=  32 * sph + (ow - 1) * hrsz + 16
 *
 * where b is the value of the 8 least significant bits of the right hand side
 * expression of the last inequality. The highest resizing ratio value will be
 * achieved when b is equal to its maximum value of 255. That resizing ratio
 * value will still satisfy the original inequality, as b will disappear when
 * the expression will be shifted right by 8.
 *
 * The reverted equations thus become
 *
 * - 8-phase, 4-tap mode
 *      hrsz = ((iw - 7) * 256 + 255 - 16 - 32 * sph) / (ow - 1)
 *      vrsz = ((ih - 4) * 256 + 255 - 16 - 32 * spv) / (oh - 1)
 * - 4-phase, 7-tap mode
 *      hrsz = ((iw - 7) * 256 + 255 - 32 - 64 * sph) / (ow - 1)
 *      vrsz = ((ih - 7) * 256 + 255 - 32 - 64 * spv) / (oh - 1)
 *
 * The ratios are integer values, and are rounded down to ensure that the
 * cropped input size is not bigger than the uncropped input size.
 *
 * As the number of phases/taps, used to select the correct equations to compute
 * the ratio, depends on the ratio, we start with the 4-tap mode equations to
 * compute an approximation of the ratio, and switch to the 7-tap mode equations
 * if the approximation is higher than the ratio threshold.
 *
 * As the 7-tap mode equations will return a ratio smaller than or equal to the
 * 4-tap mode equations, the resulting ratio could become lower than or equal to
 * the ratio threshold. This 'equations loop' isn't an issue as long as the
 * correct equations are used to compute the final input size. Starting with the
 * 4-tap mode equations ensure that, in case of values resulting in a 'ratio
 * loop', the smallest of the ratio values will be used, never exceeding the
 * requested input size.
 *
 * We first clamp the output size according to the hardware capability to avoid
 * auto-cropping the input more than required to satisfy the TRM equations. The
 * minimum output size is achieved with a scaling factor of 1024. It is thus
 * computed using the 7-tap equations.
 *
 *      min ow = ((iw - 7) * 256 - 32 - 64 * sph) / 1024 + 1
 *      min oh = ((ih - 7) * 256 - 32 - 64 * spv) / 1024 + 1
 *
 * Similarly, the maximum output size is achieved with a scaling factor of 64
 * and computed using the 4-tap equations.
 *
 *      max ow = ((iw - 7) * 256 + 255 - 16 - 32 * sph) / 64 + 1
 *      max oh = ((ih - 4) * 256 + 255 - 16 - 32 * spv) / 64 + 1
 *
 * The additional +255 term compensates for the round down operation performed
 * by the TRM equations when shifting the value right by 8 bits.
 *
 * We then compute and clamp the ratios (x1/4 ~ x4). Clamping the output size to
 * the maximum value guarantees that the ratio value will never be smaller than
 * the minimum, but it could still slightly exceed the maximum. Clamping the
 * ratio will thus result in a resizing factor slightly larger than the
 * requested value.
 *
 * To accommodate that, and make sure the TRM equations are satisfied exactly, we
 * compute the input crop rectangle as the last step.
 *
 * As if the situation wasn't complex enough, the maximum output width depends
 * on the vertical resizing ratio.  Fortunately, the output height doesn't
 * depend on the horizontal resizing ratio. We can then start by computing the
 * output height and the vertical ratio, and then move to computing the output
 * width and the horizontal ratio.
 */
static void resizer_calc_ratios(struct isp_res_device *res,
                                struct v4l2_rect *input,
                                struct v4l2_mbus_framefmt *output,
                                struct resizer_ratio *ratio)
{
        struct isp_device *isp = to_isp_device(res);
        const unsigned int spv = DEFAULT_PHASE;
        const unsigned int sph = DEFAULT_PHASE;
        unsigned int upscaled_width;
        unsigned int upscaled_height;
        unsigned int min_width;
        unsigned int min_height;
        unsigned int max_width;
        unsigned int max_height;
        unsigned int width_alignment;
        unsigned int width;
        unsigned int height;

        /*
         * Clamp the output height based on the hardware capabilities and
         * compute the vertical resizing ratio.
         */
        min_height = ((input->height - 7) * 256 - 32 - 64 * spv) / 1024 + 1;
        min_height = max_t(unsigned int, min_height, MIN_OUT_HEIGHT);
        max_height = ((input->height - 4) * 256 + 255 - 16 - 32 * spv) / 64 + 1;
        max_height = min_t(unsigned int, max_height, MAX_OUT_HEIGHT);
        output->height = clamp(output->height, min_height, max_height);

        ratio->vert = ((input->height - 4) * 256 + 255 - 16 - 32 * spv)
                    / (output->height - 1);
        if (ratio->vert > MID_RESIZE_VALUE)
                ratio->vert = ((input->height - 7) * 256 + 255 - 32 - 64 * spv)
                            / (output->height - 1);
        ratio->vert = clamp_t(unsigned int, ratio->vert,
                              MIN_RESIZE_VALUE, MAX_RESIZE_VALUE);

        if (ratio->vert <= MID_RESIZE_VALUE) {
                upscaled_height = (output->height - 1) * ratio->vert
                                + 32 * spv + 16;
                height = (upscaled_height >> 8) + 4;
        } else {
                upscaled_height = (output->height - 1) * ratio->vert
                                + 64 * spv + 32;
                height = (upscaled_height >> 8) + 7;
        }

        /*
         * Compute the minimum and maximum output widths based on the hardware
         * capabilities. The maximum depends on the vertical resizing ratio.
         */
        min_width = ((input->width - 7) * 256 - 32 - 64 * sph) / 1024 + 1;
        min_width = max_t(unsigned int, min_width, MIN_OUT_WIDTH);

        if (ratio->vert <= MID_RESIZE_VALUE) {
                switch (isp->revision) {
                case ISP_REVISION_1_0:
                        max_width = MAX_4TAP_OUT_WIDTH_ES1;
                        break;

                case ISP_REVISION_2_0:
                default:
                        max_width = MAX_4TAP_OUT_WIDTH_ES2;
                        break;

                case ISP_REVISION_15_0:
                        max_width = MAX_4TAP_OUT_WIDTH_3630;
                        break;
                }
        } else {
                switch (isp->revision) {
                case ISP_REVISION_1_0:
                        max_width = MAX_7TAP_OUT_WIDTH_ES1;
                        break;

                case ISP_REVISION_2_0:
                default:
                        max_width = MAX_7TAP_OUT_WIDTH_ES2;
                        break;

                case ISP_REVISION_15_0:
                        max_width = MAX_7TAP_OUT_WIDTH_3630;
                        break;
                }
        }
        max_width = min(((input->width - 7) * 256 + 255 - 16 - 32 * sph) / 64
                        + 1, max_width);

        /*
         * The output width must be even, and must be a multiple of 16 bytes
         * when upscaling vertically. Clamp the output width to the valid range.
         * Take the alignment into account (the maximum width in 7-tap mode on
         * ES2 isn't a multiple of 8) and align the result up to make sure it
         * won't be smaller than the minimum.
         */
        width_alignment = ratio->vert < 256 ? 8 : 2;
        output->width = clamp(output->width, min_width,
                              max_width & ~(width_alignment - 1));
        output->width = ALIGN(output->width, width_alignment);

        ratio->horz = ((input->width - 7) * 256 + 255 - 16 - 32 * sph)
                    / (output->width - 1);
        if (ratio->horz > MID_RESIZE_VALUE)
                ratio->horz = ((input->width - 7) * 256 + 255 - 32 - 64 * sph)
                            / (output->width - 1);
        ratio->horz = clamp_t(unsigned int, ratio->horz,
                              MIN_RESIZE_VALUE, MAX_RESIZE_VALUE);

        if (ratio->horz <= MID_RESIZE_VALUE) {
                upscaled_width = (output->width - 1) * ratio->horz
                               + 32 * sph + 16;
                width = (upscaled_width >> 8) + 7;
        } else {
                upscaled_width = (output->width - 1) * ratio->horz
                               + 64 * sph + 32;
                width = (upscaled_width >> 8) + 7;
        }

        /* Center the new crop rectangle. */
        input->left += (input->width - width) / 2;
        input->top += (input->height - height) / 2;
        input->width = width;
        input->height = height;
}

/*
 * resizer_set_crop_params - Setup hardware with cropping parameters
 * @res : resizer private structure
 * @input : format on sink pad
 * @output : format on source pad
 * return none
 */
static void resizer_set_crop_params(struct isp_res_device *res,
                                    const struct v4l2_mbus_framefmt *input,
                                    const struct v4l2_mbus_framefmt *output)
{
        resizer_set_ratio(res, &res->ratio);

        /* Set chrominance horizontal algorithm */
        if (res->ratio.horz >= RESIZE_DIVISOR)
                resizer_set_bilinear(res, RSZ_THE_SAME);
        else
                resizer_set_bilinear(res, RSZ_BILINEAR);

        resizer_adjust_bandwidth(res);

        if (res->input == RESIZER_INPUT_MEMORY) {
                /* Calculate additional offset for crop */
                res->crop_offset = (res->crop.active.top * input->width +
                                    res->crop.active.left) * 2;
                /*
                 * Write lowest 4 bits of horizontal pixel offset (in pixels),
                 * vertical start must be 0.
                 */
                resizer_set_start(res, (res->crop_offset / 2) & 0xf, 0);

                /*
                 * Set start (read) address for cropping, in bytes.
                 * Lowest 5 bits must be zero.
                 */
                __resizer_set_inaddr(res,
                                res->addr_base + (res->crop_offset & ~0x1f));
        } else {
                /*
                 * Set vertical start line and horizontal starting pixel.
                 * If the input is from CCDC/PREV, horizontal start field is
                 * in bytes (twice number of pixels).
                 */
                resizer_set_start(res, res->crop.active.left * 2,
                                  res->crop.active.top);
                /* Input address and offset must be 0 for preview/ccdc input */
                __resizer_set_inaddr(res, 0);
                resizer_set_input_offset(res, 0);
        }

        /* Set the input size */
        resizer_set_input_size(res, res->crop.active.width,
                               res->crop.active.height);
}

static void resizer_configure(struct isp_res_device *res)
{
        struct v4l2_mbus_framefmt *informat, *outformat;
        struct resizer_luma_yenh luma = {0, 0, 0, 0};

        resizer_set_source(res, res->input);

        informat = &res->formats[RESZ_PAD_SINK];
        outformat = &res->formats[RESZ_PAD_SOURCE];

        /* RESZ_PAD_SINK */
        if (res->input == RESIZER_INPUT_VP)
                resizer_set_input_offset(res, 0);
        else
                resizer_set_input_offset(res, ALIGN(informat->width, 0x10) * 2);

        /* YUV422 interleaved, default phase, no luma enhancement */
        resizer_set_intype(res, RSZ_YUV422);
        resizer_set_ycpos(res, informat->code);
        resizer_set_phase(res, DEFAULT_PHASE, DEFAULT_PHASE);
        resizer_set_luma(res, &luma);

        /* RESZ_PAD_SOURCE */
        resizer_set_output_offset(res, ALIGN(outformat->width * 2, 32));
        resizer_set_output_size(res, outformat->width, outformat->height);

        resizer_set_crop_params(res, informat, outformat);
}

/* -----------------------------------------------------------------------------
 * Interrupt handling
 */

static void resizer_enable_oneshot(struct isp_res_device *res)
{
        struct isp_device *isp = to_isp_device(res);

        isp_reg_set(isp, OMAP3_ISP_IOMEM_RESZ, ISPRSZ_PCR,
                    ISPRSZ_PCR_ENABLE | ISPRSZ_PCR_ONESHOT);
}

void omap3isp_resizer_isr_frame_sync(struct isp_res_device *res)
{
        /*
         * If ISP_VIDEO_DMAQUEUE_QUEUED is set, DMA queue had an underrun
         * condition, the module was paused and now we have a buffer queued
         * on the output again. Restart the pipeline if running in continuous
         * mode.
         */
        if (res->state == ISP_PIPELINE_STREAM_CONTINUOUS &&
            res->video_out.dmaqueue_flags & ISP_VIDEO_DMAQUEUE_QUEUED) {
                resizer_enable_oneshot(res);
                isp_video_dmaqueue_flags_clr(&res->video_out);
        }
}

static void resizer_isr_buffer(struct isp_res_device *res)
{
        struct isp_pipeline *pipe = to_isp_pipeline(&res->subdev.entity);
        struct isp_buffer *buffer;
        int restart = 0;

        if (res->state == ISP_PIPELINE_STREAM_STOPPED)
                return;

        /* Complete the output buffer and, if reading from memory, the input
         * buffer.
         */
        buffer = omap3isp_video_buffer_next(&res->video_out);
        if (buffer != NULL) {
                resizer_set_outaddr(res, buffer->dma);
                restart = 1;
        }

        pipe->state |= ISP_PIPELINE_IDLE_OUTPUT;

        if (res->input == RESIZER_INPUT_MEMORY) {
                buffer = omap3isp_video_buffer_next(&res->video_in);
                if (buffer != NULL)
                        resizer_set_inaddr(res, buffer->dma);
                pipe->state |= ISP_PIPELINE_IDLE_INPUT;
        }

        if (res->state == ISP_PIPELINE_STREAM_SINGLESHOT) {
                if (isp_pipeline_ready(pipe))
                        omap3isp_pipeline_set_stream(pipe,
                                                ISP_PIPELINE_STREAM_SINGLESHOT);
        } else {
                /* If an underrun occurs, the video queue operation handler will
                 * restart the resizer. Otherwise restart it immediately.
                 */
                if (restart)
                        resizer_enable_oneshot(res);
        }
}

/*
 * omap3isp_resizer_isr - ISP resizer interrupt handler
 *
 * Manage the resizer video buffers and configure shadowed and busy-locked
 * registers.
 */
void omap3isp_resizer_isr(struct isp_res_device *res)
{
        struct v4l2_mbus_framefmt *informat, *outformat;
        unsigned long flags;

        if (omap3isp_module_sync_is_stopping(&res->wait, &res->stopping))
                return;

        spin_lock_irqsave(&res->lock, flags);

        if (res->applycrop) {
                outformat = __resizer_get_format(res, NULL, RESZ_PAD_SOURCE,
                                              V4L2_SUBDEV_FORMAT_ACTIVE);
                informat = __resizer_get_format(res, NULL, RESZ_PAD_SINK,
                                              V4L2_SUBDEV_FORMAT_ACTIVE);
                resizer_set_crop_params(res, informat, outformat);
                res->applycrop = 0;
        }

        spin_unlock_irqrestore(&res->lock, flags);

        resizer_isr_buffer(res);
}

/* -----------------------------------------------------------------------------
 * ISP video operations
 */

static int resizer_video_queue(struct isp_video *video,
                               struct isp_buffer *buffer)
{
        struct isp_res_device *res = &video->isp->isp_res;

        if (video->type == V4L2_BUF_TYPE_VIDEO_OUTPUT)
                resizer_set_inaddr(res, buffer->dma);

        /*
         * We now have a buffer queued on the output. Despite what the
         * TRM says, the resizer can't be restarted immediately.
         * Enabling it in one shot mode in the middle of a frame (or at
         * least asynchronously to the frame) results in the output
         * being shifted randomly left/right and up/down, as if the
         * hardware didn't synchronize itself to the beginning of the
         * frame correctly.
         *
         * Restart the resizer on the next sync interrupt if running in
         * continuous mode or when starting the stream.
         */
        if (video->type == V4L2_BUF_TYPE_VIDEO_CAPTURE)
                resizer_set_outaddr(res, buffer->dma);

        return 0;
}

static const struct isp_video_operations resizer_video_ops = {
        .queue = resizer_video_queue,
};

/* -----------------------------------------------------------------------------
 * V4L2 subdev operations
 */

/*
 * resizer_set_stream - Enable/Disable streaming on resizer subdev
 * @sd: ISP resizer V4L2 subdev
 * @enable: 1 == Enable, 0 == Disable
 *
 * The resizer hardware can't be enabled without a memory buffer to write to.
 * As the s_stream operation is called in response to a STREAMON call without
 * any buffer queued yet, just update the state field and return immediately.
 * The resizer will be enabled in resizer_video_queue().
 */
static int resizer_set_stream(struct v4l2_subdev *sd, int enable)
{
        struct isp_res_device *res = v4l2_get_subdevdata(sd);
        struct isp_video *video_out = &res->video_out;
        struct isp_device *isp = to_isp_device(res);
        struct device *dev = to_device(res);

        if (res->state == ISP_PIPELINE_STREAM_STOPPED) {
                if (enable == ISP_PIPELINE_STREAM_STOPPED)
                        return 0;

                omap3isp_subclk_enable(isp, OMAP3_ISP_SUBCLK_RESIZER);
                resizer_configure(res);
                resizer_print_status(res);
        }

        switch (enable) {
        case ISP_PIPELINE_STREAM_CONTINUOUS:
                omap3isp_sbl_enable(isp, OMAP3_ISP_SBL_RESIZER_WRITE);
                if (video_out->dmaqueue_flags & ISP_VIDEO_DMAQUEUE_QUEUED) {
                        resizer_enable_oneshot(res);
                        isp_video_dmaqueue_flags_clr(video_out);
                }
                break;

        case ISP_PIPELINE_STREAM_SINGLESHOT:
                if (res->input == RESIZER_INPUT_MEMORY)
                        omap3isp_sbl_enable(isp, OMAP3_ISP_SBL_RESIZER_READ);
                omap3isp_sbl_enable(isp, OMAP3_ISP_SBL_RESIZER_WRITE);

                resizer_enable_oneshot(res);
                break;

        case ISP_PIPELINE_STREAM_STOPPED:
                if (omap3isp_module_sync_idle(&sd->entity, &res->wait,
                                              &res->stopping))
                        dev_dbg(dev, "%s: module stop timeout.\n", sd->name);
                omap3isp_sbl_disable(isp, OMAP3_ISP_SBL_RESIZER_READ |
                                OMAP3_ISP_SBL_RESIZER_WRITE);
                omap3isp_subclk_disable(isp, OMAP3_ISP_SUBCLK_RESIZER);
                isp_video_dmaqueue_flags_clr(video_out);
                break;
        }

        res->state = enable;
        return 0;
}

/*
 * resizer_try_crop - mangles crop parameters.
 */
static void resizer_try_crop(const struct v4l2_mbus_framefmt *sink,
                             const struct v4l2_mbus_framefmt *source,
                             struct v4l2_rect *crop)
{
        const unsigned int spv = DEFAULT_PHASE;
        const unsigned int sph = DEFAULT_PHASE;

        /* Crop rectangle is constrained by the output size so that zoom ratio
         * cannot exceed +/-4.0.
         */
        unsigned int min_width =
                ((32 * sph + (source->width - 1) * 64 + 16) >> 8) + 7;
        unsigned int min_height =
                ((32 * spv + (source->height - 1) * 64 + 16) >> 8) + 4;
        unsigned int max_width =
                ((64 * sph + (source->width - 1) * 1024 + 32) >> 8) + 7;
        unsigned int max_height =
                ((64 * spv + (source->height - 1) * 1024 + 32) >> 8) + 7;

        crop->width = clamp_t(u32, crop->width, min_width, max_width);
        crop->height = clamp_t(u32, crop->height, min_height, max_height);

        /* Crop can not go beyond of the input rectangle */
        crop->left = clamp_t(u32, crop->left, 0, sink->width - MIN_IN_WIDTH);
        crop->width = clamp_t(u32, crop->width, MIN_IN_WIDTH,
                              sink->width - crop->left);
        crop->top = clamp_t(u32, crop->top, 0, sink->height - MIN_IN_HEIGHT);
        crop->height = clamp_t(u32, crop->height, MIN_IN_HEIGHT,
                               sink->height - crop->top);
}

/*
 * resizer_get_selection - Retrieve a selection rectangle on a pad
 * @sd: ISP resizer V4L2 subdevice
 * @cfg: V4L2 subdev pad configuration
 * @sel: Selection rectangle
 *
 * The only supported rectangles are the crop rectangles on the sink pad.
 *
 * Return 0 on success or a negative error code otherwise.
 */
static int resizer_get_selection(struct v4l2_subdev *sd,
                                 struct v4l2_subdev_pad_config *cfg,
                                 struct v4l2_subdev_selection *sel)
{
        struct isp_res_device *res = v4l2_get_subdevdata(sd);
        struct v4l2_mbus_framefmt *format_source;
        struct v4l2_mbus_framefmt *format_sink;
        struct resizer_ratio ratio;

        if (sel->pad != RESZ_PAD_SINK)
                return -EINVAL;

        format_sink = __resizer_get_format(res, cfg, RESZ_PAD_SINK,
                                           sel->which);
        format_source = __resizer_get_format(res, cfg, RESZ_PAD_SOURCE,
                                             sel->which);

        switch (sel->target) {
        case V4L2_SEL_TGT_CROP_BOUNDS:
                sel->r.left = 0;
                sel->r.top = 0;
                sel->r.width = INT_MAX;
                sel->r.height = INT_MAX;

                resizer_try_crop(format_sink, format_source, &sel->r);
                resizer_calc_ratios(res, &sel->r, format_source, &ratio);
                break;

        case V4L2_SEL_TGT_CROP:
                sel->r = *__resizer_get_crop(res, cfg, sel->which);
                resizer_calc_ratios(res, &sel->r, format_source, &ratio);
                break;

        default:
                return -EINVAL;
        }

        return 0;
}

/*
 * resizer_set_selection - Set a selection rectangle on a pad
 * @sd: ISP resizer V4L2 subdevice
 * @cfg: V4L2 subdev pad configuration
 * @sel: Selection rectangle
 *
 * The only supported rectangle is the actual crop rectangle on the sink pad.
 *
 * FIXME: This function currently behaves as if the KEEP_CONFIG selection flag
 * was always set.
 *
 * Return 0 on success or a negative error code otherwise.
 */
static int resizer_set_selection(struct v4l2_subdev *sd,
                                 struct v4l2_subdev_pad_config *cfg,
                                 struct v4l2_subdev_selection *sel)
{
        struct isp_res_device *res = v4l2_get_subdevdata(sd);
        struct isp_device *isp = to_isp_device(res);
        const struct v4l2_mbus_framefmt *format_sink;
        struct v4l2_mbus_framefmt format_source;
        struct resizer_ratio ratio;
        unsigned long flags;

        if (sel->target != V4L2_SEL_TGT_CROP ||
            sel->pad != RESZ_PAD_SINK)
                return -EINVAL;

        format_sink = __resizer_get_format(res, cfg, RESZ_PAD_SINK,
                                           sel->which);
        format_source = *__resizer_get_format(res, cfg, RESZ_PAD_SOURCE,
                                              sel->which);

        dev_dbg(isp->dev, "%s(%s): req %ux%u -> (%d,%d)/%ux%u -> %ux%u\n",
                __func__, sel->which == V4L2_SUBDEV_FORMAT_TRY ? "try" : "act",
                format_sink->width, format_sink->height,
                sel->r.left, sel->r.top, sel->r.width, sel->r.height,
                format_source.width, format_source.height);

        /* Clamp the crop rectangle to the bounds, and then mangle it further to
         * fulfill the TRM equations. Store the clamped but otherwise unmangled
         * rectangle to avoid cropping the input multiple times: when an
         * application sets the output format, the current crop rectangle is
         * mangled during crop rectangle computation, which would lead to a new,
         * smaller input crop rectangle every time the output size is set if we
         * stored the mangled rectangle.
         */
        resizer_try_crop(format_sink, &format_source, &sel->r);
        *__resizer_get_crop(res, cfg, sel->which) = sel->r;
        resizer_calc_ratios(res, &sel->r, &format_source, &ratio);

        dev_dbg(isp->dev, "%s(%s): got %ux%u -> (%d,%d)/%ux%u -> %ux%u\n",
                __func__, sel->which == V4L2_SUBDEV_FORMAT_TRY ? "try" : "act",
                format_sink->width, format_sink->height,
                sel->r.left, sel->r.top, sel->r.width, sel->r.height,
                format_source.width, format_source.height);

        if (sel->which == V4L2_SUBDEV_FORMAT_TRY) {
                *__resizer_get_format(res, cfg, RESZ_PAD_SOURCE, sel->which) =
                        format_source;
                return 0;
        }

        /* Update the source format, resizing ratios and crop rectangle. If
         * streaming is on the IRQ handler will reprogram the resizer after the
         * current frame. We thus we need to protect against race conditions.
         */
        spin_lock_irqsave(&res->lock, flags);

        *__resizer_get_format(res, cfg, RESZ_PAD_SOURCE, sel->which) =
                format_source;

        res->ratio = ratio;
        res->crop.active = sel->r;

        if (res->state != ISP_PIPELINE_STREAM_STOPPED)
                res->applycrop = 1;

        spin_unlock_irqrestore(&res->lock, flags);

        return 0;
}

/* resizer pixel formats */
static const unsigned int resizer_formats[] = {
        MEDIA_BUS_FMT_UYVY8_1X16,
        MEDIA_BUS_FMT_YUYV8_1X16,
};

static unsigned int resizer_max_in_width(struct isp_res_device *res)
{
        struct isp_device *isp = to_isp_device(res);

        if (res->input == RESIZER_INPUT_MEMORY) {
                return MAX_IN_WIDTH_MEMORY_MODE;
        } else {
                if (isp->revision == ISP_REVISION_1_0)
                        return MAX_IN_WIDTH_ONTHEFLY_MODE_ES1;
                else
                        return MAX_IN_WIDTH_ONTHEFLY_MODE_ES2;
        }
}

/*
 * resizer_try_format - Handle try format by pad subdev method
 * @res   : ISP resizer device
 * @cfg: V4L2 subdev pad configuration
 * @pad   : pad num
 * @fmt   : pointer to v4l2 format structure
 * @which : wanted subdev format
 */
static void resizer_try_format(struct isp_res_device *res,
                               struct v4l2_subdev_pad_config *cfg, unsigned int pad,
                               struct v4l2_mbus_framefmt *fmt,
                               enum v4l2_subdev_format_whence which)
{
        struct v4l2_mbus_framefmt *format;
        struct resizer_ratio ratio;
        struct v4l2_rect crop;

        switch (pad) {
        case RESZ_PAD_SINK:
                if (fmt->code != MEDIA_BUS_FMT_YUYV8_1X16 &&
                    fmt->code != MEDIA_BUS_FMT_UYVY8_1X16)
                        fmt->code = MEDIA_BUS_FMT_YUYV8_1X16;

                fmt->width = clamp_t(u32, fmt->width, MIN_IN_WIDTH,
                                     resizer_max_in_width(res));
                fmt->height = clamp_t(u32, fmt->height, MIN_IN_HEIGHT,
                                      MAX_IN_HEIGHT);
                break;

        case RESZ_PAD_SOURCE:
                format = __resizer_get_format(res, cfg, RESZ_PAD_SINK, which);
                fmt->code = format->code;

                crop = *__resizer_get_crop(res, cfg, which);
                resizer_calc_ratios(res, &crop, fmt, &ratio);
                break;
        }

        fmt->colorspace = V4L2_COLORSPACE_JPEG;
        fmt->field = V4L2_FIELD_NONE;
}

/*
 * resizer_enum_mbus_code - Handle pixel format enumeration
 * @sd     : pointer to v4l2 subdev structure
 * @cfg: V4L2 subdev pad configuration
 * @code   : pointer to v4l2_subdev_mbus_code_enum structure
 * return -EINVAL or zero on success
 */
static int resizer_enum_mbus_code(struct v4l2_subdev *sd,
                                  struct v4l2_subdev_pad_config *cfg,
                                  struct v4l2_subdev_mbus_code_enum *code)
{
        struct isp_res_device *res = v4l2_get_subdevdata(sd);
        struct v4l2_mbus_framefmt *format;

        if (code->pad == RESZ_PAD_SINK) {
                if (code->index >= ARRAY_SIZE(resizer_formats))
                        return -EINVAL;

                code->code = resizer_formats[code->index];
        } else {
                if (code->index != 0)
                        return -EINVAL;

                format = __resizer_get_format(res, cfg, RESZ_PAD_SINK,
                                              code->which);
                code->code = format->code;
        }

        return 0;
}

static int resizer_enum_frame_size(struct v4l2_subdev *sd,
                                   struct v4l2_subdev_pad_config *cfg,
                                   struct v4l2_subdev_frame_size_enum *fse)
{
        struct isp_res_device *res = v4l2_get_subdevdata(sd);
        struct v4l2_mbus_framefmt format;

        if (fse->index != 0)
                return -EINVAL;

        format.code = fse->code;
        format.width = 1;
        format.height = 1;
        resizer_try_format(res, cfg, fse->pad, &format, fse->which);
        fse->min_width = format.width;
        fse->min_height = format.height;

        if (format.code != fse->code)
                return -EINVAL;

        format.code = fse->code;
        format.width = -1;
        format.height = -1;
        resizer_try_format(res, cfg, fse->pad, &format, fse->which);
        fse->max_width = format.width;
        fse->max_height = format.height;

        return 0;
}

/*
 * resizer_get_format - Handle get format by pads subdev method
 * @sd    : pointer to v4l2 subdev structure
 * @cfg: V4L2 subdev pad configuration
 * @fmt   : pointer to v4l2 subdev format structure
 * return -EINVAL or zero on success
 */
static int resizer_get_format(struct v4l2_subdev *sd, struct v4l2_subdev_pad_config *cfg,
                              struct v4l2_subdev_format *fmt)
{
        struct isp_res_device *res = v4l2_get_subdevdata(sd);
        struct v4l2_mbus_framefmt *format;

        format = __resizer_get_format(res, cfg, fmt->pad, fmt->which);
        if (format == NULL)
                return -EINVAL;

        fmt->format = *format;
        return 0;
}

/*
 * resizer_set_format - Handle set format by pads subdev method
 * @sd    : pointer to v4l2 subdev structure
 * @cfg: V4L2 subdev pad configuration
 * @fmt   : pointer to v4l2 subdev format structure
 * return -EINVAL or zero on success
 */
static int resizer_set_format(struct v4l2_subdev *sd, struct v4l2_subdev_pad_config *cfg,
                              struct v4l2_subdev_format *fmt)
{
        struct isp_res_device *res = v4l2_get_subdevdata(sd);
        struct v4l2_mbus_framefmt *format;
        struct v4l2_rect *crop;

        format = __resizer_get_format(res, cfg, fmt->pad, fmt->which);
        if (format == NULL)
                return -EINVAL;

        resizer_try_format(res, cfg, fmt->pad, &fmt->format, fmt->which);
        *format = fmt->format;

        if (fmt->pad == RESZ_PAD_SINK) {
                /* reset crop rectangle */
                crop = __resizer_get_crop(res, cfg, fmt->which);
                crop->left = 0;
                crop->top = 0;
                crop->width = fmt->format.width;
                crop->height = fmt->format.height;

                /* Propagate the format from sink to source */
                format = __resizer_get_format(res, cfg, RESZ_PAD_SOURCE,
                                              fmt->which);
                *format = fmt->format;
                resizer_try_format(res, cfg, RESZ_PAD_SOURCE, format,
                                   fmt->which);
        }

        if (fmt->which == V4L2_SUBDEV_FORMAT_ACTIVE) {
                /* Compute and store the active crop rectangle and resizer
                 * ratios. format already points to the source pad active
                 * format.
                 */
                res->crop.active = res->crop.request;
                resizer_calc_ratios(res, &res->crop.active, format,
                                       &res->ratio);
        }

        return 0;
}

static int resizer_link_validate(struct v4l2_subdev *sd,
                                 struct media_link *link,
                                 struct v4l2_subdev_format *source_fmt,
                                 struct v4l2_subdev_format *sink_fmt)
{
        struct isp_res_device *res = v4l2_get_subdevdata(sd);
        struct isp_pipeline *pipe = to_isp_pipeline(&sd->entity);

        omap3isp_resizer_max_rate(res, &pipe->max_rate);

        return v4l2_subdev_link_validate_default(sd, link,
                                                 source_fmt, sink_fmt);
}

/*
 * resizer_init_formats - Initialize formats on all pads
 * @sd: ISP resizer V4L2 subdevice
 * @fh: V4L2 subdev file handle
 *
 * Initialize all pad formats with default values. If fh is not NULL, try
 * formats are initialized on the file handle. Otherwise active formats are
 * initialized on the device.
 */
static int resizer_init_formats(struct v4l2_subdev *sd,
                                struct v4l2_subdev_fh *fh)
{
        struct v4l2_subdev_format format;

        memset(&format, 0, sizeof(format));
        format.pad = RESZ_PAD_SINK;
        format.which = fh ? V4L2_SUBDEV_FORMAT_TRY : V4L2_SUBDEV_FORMAT_ACTIVE;
        format.format.code = MEDIA_BUS_FMT_YUYV8_1X16;
        format.format.width = 4096;
        format.format.height = 4096;
        resizer_set_format(sd, fh ? fh->pad : NULL, &format);

        return 0;
}

/* subdev video operations */
static const struct v4l2_subdev_video_ops resizer_v4l2_video_ops = {
        .s_stream = resizer_set_stream,
};

/* subdev pad operations */
static const struct v4l2_subdev_pad_ops resizer_v4l2_pad_ops = {
        .enum_mbus_code = resizer_enum_mbus_code,
        .enum_frame_size = resizer_enum_frame_size,
        .get_fmt = resizer_get_format,
        .set_fmt = resizer_set_format,
        .get_selection = resizer_get_selection,
        .set_selection = resizer_set_selection,
        .link_validate = resizer_link_validate,
};

/* subdev operations */
static const struct v4l2_subdev_ops resizer_v4l2_ops = {
        .video = &resizer_v4l2_video_ops,
        .pad = &resizer_v4l2_pad_ops,
};

/* subdev internal operations */
static const struct v4l2_subdev_internal_ops resizer_v4l2_internal_ops = {
        .open = resizer_init_formats,
};

/* -----------------------------------------------------------------------------
 * Media entity operations
 */

/*
 * resizer_link_setup - Setup resizer connections.
 * @entity : Pointer to media entity structure
 * @local  : Pointer to local pad array
 * @remote : Pointer to remote pad array
 * @flags  : Link flags
 * return -EINVAL or zero on success
 */
static int resizer_link_setup(struct media_entity *entity,
                              const struct media_pad *local,
                              const struct media_pad *remote, u32 flags)
{
        struct v4l2_subdev *sd = media_entity_to_v4l2_subdev(entity);
        struct isp_res_device *res = v4l2_get_subdevdata(sd);
        unsigned int index = local->index;

        /* FIXME: this is actually a hack! */
        if (is_media_entity_v4l2_subdev(remote->entity))
                index |= 2 << 16;

        switch (index) {
        case RESZ_PAD_SINK:
                /* read from memory */
                if (flags & MEDIA_LNK_FL_ENABLED) {
                        if (res->input == RESIZER_INPUT_VP)
                                return -EBUSY;
                        res->input = RESIZER_INPUT_MEMORY;
                } else {
                        if (res->input == RESIZER_INPUT_MEMORY)
                                res->input = RESIZER_INPUT_NONE;
                }
                break;

        case RESZ_PAD_SINK | 2 << 16:
                /* read from ccdc or previewer */
                if (flags & MEDIA_LNK_FL_ENABLED) {
                        if (res->input == RESIZER_INPUT_MEMORY)
                                return -EBUSY;
                        res->input = RESIZER_INPUT_VP;
                } else {
                        if (res->input == RESIZER_INPUT_VP)
                                res->input = RESIZER_INPUT_NONE;
                }
                break;

        case RESZ_PAD_SOURCE:
                /* resizer always write to memory */
                break;

        default:
                return -EINVAL;
        }

        return 0;
}

/* media operations */
static const struct media_entity_operations resizer_media_ops = {
        .link_setup = resizer_link_setup,
        .link_validate = v4l2_subdev_link_validate,
};

void omap3isp_resizer_unregister_entities(struct isp_res_device *res)
{
        v4l2_device_unregister_subdev(&res->subdev);
        omap3isp_video_unregister(&res->video_in);
        omap3isp_video_unregister(&res->video_out);
}

int omap3isp_resizer_register_entities(struct isp_res_device *res,
                                       struct v4l2_device *vdev)
{
        int ret;

        /* Register the subdev and video nodes. */
        res->subdev.dev = vdev->mdev->dev;
        ret = v4l2_device_register_subdev(vdev, &res->subdev);
        if (ret < 0)
                goto error;

        ret = omap3isp_video_register(&res->video_in, vdev);
        if (ret < 0)
                goto error;

        ret = omap3isp_video_register(&res->video_out, vdev);
        if (ret < 0)
                goto error;

        return 0;

error:
        omap3isp_resizer_unregister_entities(res);
        return ret;
}

/* -----------------------------------------------------------------------------
 * ISP resizer initialization and cleanup
 */

/*
 * resizer_init_entities - Initialize resizer subdev and media entity.
 * @res : Pointer to resizer device structure
 * return -ENOMEM or zero on success
 */
static int resizer_init_entities(struct isp_res_device *res)
{
        struct v4l2_subdev *sd = &res->subdev;
        struct media_pad *pads = res->pads;
        struct media_entity *me = &sd->entity;
        int ret;

        res->input = RESIZER_INPUT_NONE;

        v4l2_subdev_init(sd, &resizer_v4l2_ops);
        sd->internal_ops = &resizer_v4l2_internal_ops;
        strscpy(sd->name, "OMAP3 ISP resizer", sizeof(sd->name));
        sd->grp_id = 1 << 16;   /* group ID for isp subdevs */
        v4l2_set_subdevdata(sd, res);
        sd->flags |= V4L2_SUBDEV_FL_HAS_DEVNODE;

        pads[RESZ_PAD_SINK].flags = MEDIA_PAD_FL_SINK
                                    | MEDIA_PAD_FL_MUST_CONNECT;
        pads[RESZ_PAD_SOURCE].flags = MEDIA_PAD_FL_SOURCE;

        me->ops = &resizer_media_ops;
        ret = media_entity_pads_init(me, RESZ_PADS_NUM, pads);
        if (ret < 0)
                return ret;

        resizer_init_formats(sd, NULL);

        res->video_in.type = V4L2_BUF_TYPE_VIDEO_OUTPUT;
        res->video_in.ops = &resizer_video_ops;
        res->video_in.isp = to_isp_device(res);
        res->video_in.capture_mem = PAGE_ALIGN(4096 * 4096) * 2 * 3;
        res->video_in.bpl_alignment = 32;
        res->video_out.type = V4L2_BUF_TYPE_VIDEO_CAPTURE;
        res->video_out.ops = &resizer_video_ops;
        res->video_out.isp = to_isp_device(res);
        res->video_out.capture_mem = PAGE_ALIGN(4096 * 4096) * 2 * 3;
        res->video_out.bpl_alignment = 32;

        ret = omap3isp_video_init(&res->video_in, "resizer");
        if (ret < 0)
                goto error_video_in;

        ret = omap3isp_video_init(&res->video_out, "resizer");
        if (ret < 0)
                goto error_video_out;

        res->video_out.video.entity.flags |= MEDIA_ENT_FL_DEFAULT;

        return 0;

error_video_out:
        omap3isp_video_cleanup(&res->video_in);
error_video_in:
        media_entity_cleanup(&res->subdev.entity);
        return ret;
}

/*
 * isp_resizer_init - Resizer initialization.
 * @isp : Pointer to ISP device
 * return -ENOMEM or zero on success
 */
int omap3isp_resizer_init(struct isp_device *isp)
{
        struct isp_res_device *res = &isp->isp_res;

        init_waitqueue_head(&res->wait);
        atomic_set(&res->stopping, 0);
        spin_lock_init(&res->lock);

        return resizer_init_entities(res);
}

void omap3isp_resizer_cleanup(struct isp_device *isp)
{
        struct isp_res_device *res = &isp->isp_res;

        omap3isp_video_cleanup(&res->video_in);
        omap3isp_video_cleanup(&res->video_out);
        media_entity_cleanup(&res->subdev.entity);
}