WIP FPC-III support
[linux/fpc-iii.git] / drivers / net / ethernet / dec / tulip / tulip_core.c
blobc1dcd6ca1457c615e7a6bf443a22e1c27c71057a
1 /* tulip_core.c: A DEC 21x4x-family ethernet driver for Linux.
3 Copyright 2000,2001 The Linux Kernel Team
4 Written/copyright 1994-2001 by Donald Becker.
6 This software may be used and distributed according to the terms
7 of the GNU General Public License, incorporated herein by reference.
9 Please submit bugs to http://bugzilla.kernel.org/ .
12 #define pr_fmt(fmt) "tulip: " fmt
14 #define DRV_NAME "tulip"
16 #include <linux/module.h>
17 #include <linux/pci.h>
18 #include <linux/slab.h>
19 #include "tulip.h"
20 #include <linux/init.h>
21 #include <linux/interrupt.h>
22 #include <linux/etherdevice.h>
23 #include <linux/delay.h>
24 #include <linux/mii.h>
25 #include <linux/crc32.h>
26 #include <asm/unaligned.h>
27 #include <linux/uaccess.h>
29 #ifdef CONFIG_SPARC
30 #include <asm/prom.h>
31 #endif
33 /* A few user-configurable values. */
35 /* Maximum events (Rx packets, etc.) to handle at each interrupt. */
36 static unsigned int max_interrupt_work = 25;
38 #define MAX_UNITS 8
39 /* Used to pass the full-duplex flag, etc. */
40 static int full_duplex[MAX_UNITS];
41 static int options[MAX_UNITS];
42 static int mtu[MAX_UNITS]; /* Jumbo MTU for interfaces. */
44 /* The possible media types that can be set in options[] are: */
45 const char * const medianame[32] = {
46 "10baseT", "10base2", "AUI", "100baseTx",
47 "10baseT-FDX", "100baseTx-FDX", "100baseT4", "100baseFx",
48 "100baseFx-FDX", "MII 10baseT", "MII 10baseT-FDX", "MII",
49 "10baseT(forced)", "MII 100baseTx", "MII 100baseTx-FDX", "MII 100baseT4",
50 "MII 100baseFx-HDX", "MII 100baseFx-FDX", "Home-PNA 1Mbps", "Invalid-19",
51 "","","","", "","","","", "","","","Transceiver reset",
54 /* Set the copy breakpoint for the copy-only-tiny-buffer Rx structure. */
55 #if defined(__alpha__) || defined(__arm__) || defined(__hppa__) || \
56 defined(CONFIG_SPARC) || defined(__ia64__) || \
57 defined(__sh__) || defined(__mips__)
58 static int rx_copybreak = 1518;
59 #else
60 static int rx_copybreak = 100;
61 #endif
64 Set the bus performance register.
65 Typical: Set 16 longword cache alignment, no burst limit.
66 Cache alignment bits 15:14 Burst length 13:8
67 0000 No alignment 0x00000000 unlimited 0800 8 longwords
68 4000 8 longwords 0100 1 longword 1000 16 longwords
69 8000 16 longwords 0200 2 longwords 2000 32 longwords
70 C000 32 longwords 0400 4 longwords
71 Warning: many older 486 systems are broken and require setting 0x00A04800
72 8 longword cache alignment, 8 longword burst.
73 ToDo: Non-Intel setting could be better.
76 #if defined(__alpha__) || defined(__ia64__)
77 static int csr0 = 0x01A00000 | 0xE000;
78 #elif defined(__i386__) || defined(__powerpc__) || defined(__x86_64__)
79 static int csr0 = 0x01A00000 | 0x8000;
80 #elif defined(CONFIG_SPARC) || defined(__hppa__)
81 /* The UltraSparc PCI controllers will disconnect at every 64-byte
82 * crossing anyways so it makes no sense to tell Tulip to burst
83 * any more than that.
85 static int csr0 = 0x01A00000 | 0x9000;
86 #elif defined(__arm__) || defined(__sh__)
87 static int csr0 = 0x01A00000 | 0x4800;
88 #elif defined(__mips__)
89 static int csr0 = 0x00200000 | 0x4000;
90 #else
91 static int csr0;
92 #endif
94 /* Operational parameters that usually are not changed. */
95 /* Time in jiffies before concluding the transmitter is hung. */
96 #define TX_TIMEOUT (4*HZ)
99 MODULE_AUTHOR("The Linux Kernel Team");
100 MODULE_DESCRIPTION("Digital 21*4* Tulip ethernet driver");
101 MODULE_LICENSE("GPL");
102 module_param(tulip_debug, int, 0);
103 module_param(max_interrupt_work, int, 0);
104 module_param(rx_copybreak, int, 0);
105 module_param(csr0, int, 0);
106 module_param_array(options, int, NULL, 0);
107 module_param_array(full_duplex, int, NULL, 0);
109 #ifdef TULIP_DEBUG
110 int tulip_debug = TULIP_DEBUG;
111 #else
112 int tulip_debug = 1;
113 #endif
115 static void tulip_timer(struct timer_list *t)
117 struct tulip_private *tp = from_timer(tp, t, timer);
118 struct net_device *dev = tp->dev;
120 if (netif_running(dev))
121 schedule_work(&tp->media_work);
125 * This table use during operation for capabilities and media timer.
127 * It is indexed via the values in 'enum chips'
130 const struct tulip_chip_table tulip_tbl[] = {
131 { }, /* placeholder for array, slot unused currently */
132 { }, /* placeholder for array, slot unused currently */
134 /* DC21140 */
135 { "Digital DS21140 Tulip", 128, 0x0001ebef,
136 HAS_MII | HAS_MEDIA_TABLE | CSR12_IN_SROM | HAS_PCI_MWI, tulip_timer,
137 tulip_media_task },
139 /* DC21142, DC21143 */
140 { "Digital DS21142/43 Tulip", 128, 0x0801fbff,
141 HAS_MII | HAS_MEDIA_TABLE | ALWAYS_CHECK_MII | HAS_ACPI | HAS_NWAY
142 | HAS_INTR_MITIGATION | HAS_PCI_MWI, tulip_timer, t21142_media_task },
144 /* LC82C168 */
145 { "Lite-On 82c168 PNIC", 256, 0x0001fbef,
146 HAS_MII | HAS_PNICNWAY, pnic_timer, },
148 /* MX98713 */
149 { "Macronix 98713 PMAC", 128, 0x0001ebef,
150 HAS_MII | HAS_MEDIA_TABLE | CSR12_IN_SROM, mxic_timer, },
152 /* MX98715 */
153 { "Macronix 98715 PMAC", 256, 0x0001ebef,
154 HAS_MEDIA_TABLE, mxic_timer, },
156 /* MX98725 */
157 { "Macronix 98725 PMAC", 256, 0x0001ebef,
158 HAS_MEDIA_TABLE, mxic_timer, },
160 /* AX88140 */
161 { "ASIX AX88140", 128, 0x0001fbff,
162 HAS_MII | HAS_MEDIA_TABLE | CSR12_IN_SROM | MC_HASH_ONLY
163 | IS_ASIX, tulip_timer, tulip_media_task },
165 /* PNIC2 */
166 { "Lite-On PNIC-II", 256, 0x0801fbff,
167 HAS_MII | HAS_NWAY | HAS_8023X | HAS_PCI_MWI, pnic2_timer, },
169 /* COMET */
170 { "ADMtek Comet", 256, 0x0001abef,
171 HAS_MII | MC_HASH_ONLY | COMET_MAC_ADDR, comet_timer, },
173 /* COMPEX9881 */
174 { "Compex 9881 PMAC", 128, 0x0001ebef,
175 HAS_MII | HAS_MEDIA_TABLE | CSR12_IN_SROM, mxic_timer, },
177 /* I21145 */
178 { "Intel DS21145 Tulip", 128, 0x0801fbff,
179 HAS_MII | HAS_MEDIA_TABLE | ALWAYS_CHECK_MII | HAS_ACPI
180 | HAS_NWAY | HAS_PCI_MWI, tulip_timer, tulip_media_task },
182 /* DM910X */
183 #ifdef CONFIG_TULIP_DM910X
184 { "Davicom DM9102/DM9102A", 128, 0x0001ebef,
185 HAS_MII | HAS_MEDIA_TABLE | CSR12_IN_SROM | HAS_ACPI,
186 tulip_timer, tulip_media_task },
187 #else
188 { NULL },
189 #endif
191 /* RS7112 */
192 { "Conexant LANfinity", 256, 0x0001ebef,
193 HAS_MII | HAS_ACPI, tulip_timer, tulip_media_task },
198 static const struct pci_device_id tulip_pci_tbl[] = {
199 { 0x1011, 0x0009, PCI_ANY_ID, PCI_ANY_ID, 0, 0, DC21140 },
200 { 0x1011, 0x0019, PCI_ANY_ID, PCI_ANY_ID, 0, 0, DC21143 },
201 { 0x11AD, 0x0002, PCI_ANY_ID, PCI_ANY_ID, 0, 0, LC82C168 },
202 { 0x10d9, 0x0512, PCI_ANY_ID, PCI_ANY_ID, 0, 0, MX98713 },
203 { 0x10d9, 0x0531, PCI_ANY_ID, PCI_ANY_ID, 0, 0, MX98715 },
204 /* { 0x10d9, 0x0531, PCI_ANY_ID, PCI_ANY_ID, 0, 0, MX98725 },*/
205 { 0x125B, 0x1400, PCI_ANY_ID, PCI_ANY_ID, 0, 0, AX88140 },
206 { 0x11AD, 0xc115, PCI_ANY_ID, PCI_ANY_ID, 0, 0, PNIC2 },
207 { 0x1317, 0x0981, PCI_ANY_ID, PCI_ANY_ID, 0, 0, COMET },
208 { 0x1317, 0x0985, PCI_ANY_ID, PCI_ANY_ID, 0, 0, COMET },
209 { 0x1317, 0x1985, PCI_ANY_ID, PCI_ANY_ID, 0, 0, COMET },
210 { 0x1317, 0x9511, PCI_ANY_ID, PCI_ANY_ID, 0, 0, COMET },
211 { 0x13D1, 0xAB02, PCI_ANY_ID, PCI_ANY_ID, 0, 0, COMET },
212 { 0x13D1, 0xAB03, PCI_ANY_ID, PCI_ANY_ID, 0, 0, COMET },
213 { 0x13D1, 0xAB08, PCI_ANY_ID, PCI_ANY_ID, 0, 0, COMET },
214 { 0x104A, 0x0981, PCI_ANY_ID, PCI_ANY_ID, 0, 0, COMET },
215 { 0x104A, 0x2774, PCI_ANY_ID, PCI_ANY_ID, 0, 0, COMET },
216 { 0x1259, 0xa120, PCI_ANY_ID, PCI_ANY_ID, 0, 0, COMET },
217 { 0x11F6, 0x9881, PCI_ANY_ID, PCI_ANY_ID, 0, 0, COMPEX9881 },
218 { 0x8086, 0x0039, PCI_ANY_ID, PCI_ANY_ID, 0, 0, I21145 },
219 #ifdef CONFIG_TULIP_DM910X
220 { 0x1282, 0x9100, PCI_ANY_ID, PCI_ANY_ID, 0, 0, DM910X },
221 { 0x1282, 0x9102, PCI_ANY_ID, PCI_ANY_ID, 0, 0, DM910X },
222 #endif
223 { 0x1113, 0x1216, PCI_ANY_ID, PCI_ANY_ID, 0, 0, COMET },
224 { 0x1113, 0x1217, PCI_ANY_ID, PCI_ANY_ID, 0, 0, MX98715 },
225 { 0x1113, 0x9511, PCI_ANY_ID, PCI_ANY_ID, 0, 0, COMET },
226 { 0x1186, 0x1541, PCI_ANY_ID, PCI_ANY_ID, 0, 0, COMET },
227 { 0x1186, 0x1561, PCI_ANY_ID, PCI_ANY_ID, 0, 0, COMET },
228 { 0x1186, 0x1591, PCI_ANY_ID, PCI_ANY_ID, 0, 0, COMET },
229 { 0x14f1, 0x1803, PCI_ANY_ID, PCI_ANY_ID, 0, 0, CONEXANT },
230 { 0x1626, 0x8410, PCI_ANY_ID, PCI_ANY_ID, 0, 0, COMET },
231 { 0x1737, 0xAB09, PCI_ANY_ID, PCI_ANY_ID, 0, 0, COMET },
232 { 0x1737, 0xAB08, PCI_ANY_ID, PCI_ANY_ID, 0, 0, COMET },
233 { 0x17B3, 0xAB08, PCI_ANY_ID, PCI_ANY_ID, 0, 0, COMET },
234 { 0x10b7, 0x9300, PCI_ANY_ID, PCI_ANY_ID, 0, 0, COMET }, /* 3Com 3CSOHO100B-TX */
235 { 0x14ea, 0xab08, PCI_ANY_ID, PCI_ANY_ID, 0, 0, COMET }, /* Planex FNW-3602-TX */
236 { 0x1414, 0x0001, PCI_ANY_ID, PCI_ANY_ID, 0, 0, COMET }, /* Microsoft MN-120 */
237 { 0x1414, 0x0002, PCI_ANY_ID, PCI_ANY_ID, 0, 0, COMET },
238 { } /* terminate list */
240 MODULE_DEVICE_TABLE(pci, tulip_pci_tbl);
243 /* A full-duplex map for media types. */
244 const char tulip_media_cap[32] =
245 {0,0,0,16, 3,19,16,24, 27,4,7,5, 0,20,23,20, 28,31,0,0, };
247 static void tulip_tx_timeout(struct net_device *dev, unsigned int txqueue);
248 static void tulip_init_ring(struct net_device *dev);
249 static void tulip_free_ring(struct net_device *dev);
250 static netdev_tx_t tulip_start_xmit(struct sk_buff *skb,
251 struct net_device *dev);
252 static int tulip_open(struct net_device *dev);
253 static int tulip_close(struct net_device *dev);
254 static void tulip_up(struct net_device *dev);
255 static void tulip_down(struct net_device *dev);
256 static struct net_device_stats *tulip_get_stats(struct net_device *dev);
257 static int private_ioctl(struct net_device *dev, struct ifreq *rq, int cmd);
258 static void set_rx_mode(struct net_device *dev);
259 static void tulip_set_wolopts(struct pci_dev *pdev, u32 wolopts);
260 #ifdef CONFIG_NET_POLL_CONTROLLER
261 static void poll_tulip(struct net_device *dev);
262 #endif
264 static void tulip_set_power_state (struct tulip_private *tp,
265 int sleep, int snooze)
267 if (tp->flags & HAS_ACPI) {
268 u32 tmp, newtmp;
269 pci_read_config_dword (tp->pdev, CFDD, &tmp);
270 newtmp = tmp & ~(CFDD_Sleep | CFDD_Snooze);
271 if (sleep)
272 newtmp |= CFDD_Sleep;
273 else if (snooze)
274 newtmp |= CFDD_Snooze;
275 if (tmp != newtmp)
276 pci_write_config_dword (tp->pdev, CFDD, newtmp);
282 static void tulip_up(struct net_device *dev)
284 struct tulip_private *tp = netdev_priv(dev);
285 void __iomem *ioaddr = tp->base_addr;
286 int next_tick = 3*HZ;
287 u32 reg;
288 int i;
290 #ifdef CONFIG_TULIP_NAPI
291 napi_enable(&tp->napi);
292 #endif
294 /* Wake the chip from sleep/snooze mode. */
295 tulip_set_power_state (tp, 0, 0);
297 /* Disable all WOL events */
298 pci_enable_wake(tp->pdev, PCI_D3hot, 0);
299 pci_enable_wake(tp->pdev, PCI_D3cold, 0);
300 tulip_set_wolopts(tp->pdev, 0);
302 /* On some chip revs we must set the MII/SYM port before the reset!? */
303 if (tp->mii_cnt || (tp->mtable && tp->mtable->has_mii))
304 iowrite32(0x00040000, ioaddr + CSR6);
306 /* Reset the chip, holding bit 0 set at least 50 PCI cycles. */
307 iowrite32(0x00000001, ioaddr + CSR0);
308 pci_read_config_dword(tp->pdev, PCI_COMMAND, &reg); /* flush write */
309 udelay(100);
311 /* Deassert reset.
312 Wait the specified 50 PCI cycles after a reset by initializing
313 Tx and Rx queues and the address filter list. */
314 iowrite32(tp->csr0, ioaddr + CSR0);
315 pci_read_config_dword(tp->pdev, PCI_COMMAND, &reg); /* flush write */
316 udelay(100);
318 if (tulip_debug > 1)
319 netdev_dbg(dev, "tulip_up(), irq==%d\n", tp->pdev->irq);
321 iowrite32(tp->rx_ring_dma, ioaddr + CSR3);
322 iowrite32(tp->tx_ring_dma, ioaddr + CSR4);
323 tp->cur_rx = tp->cur_tx = 0;
324 tp->dirty_rx = tp->dirty_tx = 0;
326 if (tp->flags & MC_HASH_ONLY) {
327 u32 addr_low = get_unaligned_le32(dev->dev_addr);
328 u32 addr_high = get_unaligned_le16(dev->dev_addr + 4);
329 if (tp->chip_id == AX88140) {
330 iowrite32(0, ioaddr + CSR13);
331 iowrite32(addr_low, ioaddr + CSR14);
332 iowrite32(1, ioaddr + CSR13);
333 iowrite32(addr_high, ioaddr + CSR14);
334 } else if (tp->flags & COMET_MAC_ADDR) {
335 iowrite32(addr_low, ioaddr + 0xA4);
336 iowrite32(addr_high, ioaddr + 0xA8);
337 iowrite32(0, ioaddr + CSR27);
338 iowrite32(0, ioaddr + CSR28);
340 } else {
341 /* This is set_rx_mode(), but without starting the transmitter. */
342 u16 *eaddrs = (u16 *)dev->dev_addr;
343 u16 *setup_frm = &tp->setup_frame[15*6];
344 dma_addr_t mapping;
346 /* 21140 bug: you must add the broadcast address. */
347 memset(tp->setup_frame, 0xff, sizeof(tp->setup_frame));
348 /* Fill the final entry of the table with our physical address. */
349 *setup_frm++ = eaddrs[0]; *setup_frm++ = eaddrs[0];
350 *setup_frm++ = eaddrs[1]; *setup_frm++ = eaddrs[1];
351 *setup_frm++ = eaddrs[2]; *setup_frm++ = eaddrs[2];
353 mapping = dma_map_single(&tp->pdev->dev, tp->setup_frame,
354 sizeof(tp->setup_frame),
355 DMA_TO_DEVICE);
356 tp->tx_buffers[tp->cur_tx].skb = NULL;
357 tp->tx_buffers[tp->cur_tx].mapping = mapping;
359 /* Put the setup frame on the Tx list. */
360 tp->tx_ring[tp->cur_tx].length = cpu_to_le32(0x08000000 | 192);
361 tp->tx_ring[tp->cur_tx].buffer1 = cpu_to_le32(mapping);
362 tp->tx_ring[tp->cur_tx].status = cpu_to_le32(DescOwned);
364 tp->cur_tx++;
367 tp->saved_if_port = dev->if_port;
368 if (dev->if_port == 0)
369 dev->if_port = tp->default_port;
371 /* Allow selecting a default media. */
372 i = 0;
373 if (tp->mtable == NULL)
374 goto media_picked;
375 if (dev->if_port) {
376 int looking_for = tulip_media_cap[dev->if_port] & MediaIsMII ? 11 :
377 (dev->if_port == 12 ? 0 : dev->if_port);
378 for (i = 0; i < tp->mtable->leafcount; i++)
379 if (tp->mtable->mleaf[i].media == looking_for) {
380 dev_info(&dev->dev,
381 "Using user-specified media %s\n",
382 medianame[dev->if_port]);
383 goto media_picked;
386 if ((tp->mtable->defaultmedia & 0x0800) == 0) {
387 int looking_for = tp->mtable->defaultmedia & MEDIA_MASK;
388 for (i = 0; i < tp->mtable->leafcount; i++)
389 if (tp->mtable->mleaf[i].media == looking_for) {
390 dev_info(&dev->dev,
391 "Using EEPROM-set media %s\n",
392 medianame[looking_for]);
393 goto media_picked;
396 /* Start sensing first non-full-duplex media. */
397 for (i = tp->mtable->leafcount - 1;
398 (tulip_media_cap[tp->mtable->mleaf[i].media] & MediaAlwaysFD) && i > 0; i--)
400 media_picked:
402 tp->csr6 = 0;
403 tp->cur_index = i;
404 tp->nwayset = 0;
406 if (dev->if_port) {
407 if (tp->chip_id == DC21143 &&
408 (tulip_media_cap[dev->if_port] & MediaIsMII)) {
409 /* We must reset the media CSRs when we force-select MII mode. */
410 iowrite32(0x0000, ioaddr + CSR13);
411 iowrite32(0x0000, ioaddr + CSR14);
412 iowrite32(0x0008, ioaddr + CSR15);
414 tulip_select_media(dev, 1);
415 } else if (tp->chip_id == DC21142) {
416 if (tp->mii_cnt) {
417 tulip_select_media(dev, 1);
418 if (tulip_debug > 1)
419 dev_info(&dev->dev,
420 "Using MII transceiver %d, status %04x\n",
421 tp->phys[0],
422 tulip_mdio_read(dev, tp->phys[0], 1));
423 iowrite32(csr6_mask_defstate, ioaddr + CSR6);
424 tp->csr6 = csr6_mask_hdcap;
425 dev->if_port = 11;
426 iowrite32(0x0000, ioaddr + CSR13);
427 iowrite32(0x0000, ioaddr + CSR14);
428 } else
429 t21142_start_nway(dev);
430 } else if (tp->chip_id == PNIC2) {
431 /* for initial startup advertise 10/100 Full and Half */
432 tp->sym_advertise = 0x01E0;
433 /* enable autonegotiate end interrupt */
434 iowrite32(ioread32(ioaddr+CSR5)| 0x00008010, ioaddr + CSR5);
435 iowrite32(ioread32(ioaddr+CSR7)| 0x00008010, ioaddr + CSR7);
436 pnic2_start_nway(dev);
437 } else if (tp->chip_id == LC82C168 && ! tp->medialock) {
438 if (tp->mii_cnt) {
439 dev->if_port = 11;
440 tp->csr6 = 0x814C0000 | (tp->full_duplex ? 0x0200 : 0);
441 iowrite32(0x0001, ioaddr + CSR15);
442 } else if (ioread32(ioaddr + CSR5) & TPLnkPass)
443 pnic_do_nway(dev);
444 else {
445 /* Start with 10mbps to do autonegotiation. */
446 iowrite32(0x32, ioaddr + CSR12);
447 tp->csr6 = 0x00420000;
448 iowrite32(0x0001B078, ioaddr + 0xB8);
449 iowrite32(0x0201B078, ioaddr + 0xB8);
450 next_tick = 1*HZ;
452 } else if ((tp->chip_id == MX98713 || tp->chip_id == COMPEX9881) &&
453 ! tp->medialock) {
454 dev->if_port = 0;
455 tp->csr6 = 0x01880000 | (tp->full_duplex ? 0x0200 : 0);
456 iowrite32(0x0f370000 | ioread16(ioaddr + 0x80), ioaddr + 0x80);
457 } else if (tp->chip_id == MX98715 || tp->chip_id == MX98725) {
458 /* Provided by BOLO, Macronix - 12/10/1998. */
459 dev->if_port = 0;
460 tp->csr6 = 0x01a80200;
461 iowrite32(0x0f370000 | ioread16(ioaddr + 0x80), ioaddr + 0x80);
462 iowrite32(0x11000 | ioread16(ioaddr + 0xa0), ioaddr + 0xa0);
463 } else if (tp->chip_id == COMET || tp->chip_id == CONEXANT) {
464 /* Enable automatic Tx underrun recovery. */
465 iowrite32(ioread32(ioaddr + 0x88) | 1, ioaddr + 0x88);
466 dev->if_port = tp->mii_cnt ? 11 : 0;
467 tp->csr6 = 0x00040000;
468 } else if (tp->chip_id == AX88140) {
469 tp->csr6 = tp->mii_cnt ? 0x00040100 : 0x00000100;
470 } else
471 tulip_select_media(dev, 1);
473 /* Start the chip's Tx to process setup frame. */
474 tulip_stop_rxtx(tp);
475 barrier();
476 udelay(5);
477 iowrite32(tp->csr6 | TxOn, ioaddr + CSR6);
479 /* Enable interrupts by setting the interrupt mask. */
480 iowrite32(tulip_tbl[tp->chip_id].valid_intrs, ioaddr + CSR5);
481 iowrite32(tulip_tbl[tp->chip_id].valid_intrs, ioaddr + CSR7);
482 tulip_start_rxtx(tp);
483 iowrite32(0, ioaddr + CSR2); /* Rx poll demand */
485 if (tulip_debug > 2) {
486 netdev_dbg(dev, "Done tulip_up(), CSR0 %08x, CSR5 %08x CSR6 %08x\n",
487 ioread32(ioaddr + CSR0),
488 ioread32(ioaddr + CSR5),
489 ioread32(ioaddr + CSR6));
492 /* Set the timer to switch to check for link beat and perhaps switch
493 to an alternate media type. */
494 tp->timer.expires = RUN_AT(next_tick);
495 add_timer(&tp->timer);
496 #ifdef CONFIG_TULIP_NAPI
497 timer_setup(&tp->oom_timer, oom_timer, 0);
498 #endif
501 static int
502 tulip_open(struct net_device *dev)
504 struct tulip_private *tp = netdev_priv(dev);
505 int retval;
507 tulip_init_ring (dev);
509 retval = request_irq(tp->pdev->irq, tulip_interrupt, IRQF_SHARED,
510 dev->name, dev);
511 if (retval)
512 goto free_ring;
514 tulip_up (dev);
516 netif_start_queue (dev);
518 return 0;
520 free_ring:
521 tulip_free_ring (dev);
522 return retval;
526 static void tulip_tx_timeout(struct net_device *dev, unsigned int txqueue)
528 struct tulip_private *tp = netdev_priv(dev);
529 void __iomem *ioaddr = tp->base_addr;
530 unsigned long flags;
532 spin_lock_irqsave (&tp->lock, flags);
534 if (tulip_media_cap[dev->if_port] & MediaIsMII) {
535 /* Do nothing -- the media monitor should handle this. */
536 if (tulip_debug > 1)
537 dev_warn(&dev->dev,
538 "Transmit timeout using MII device\n");
539 } else if (tp->chip_id == DC21140 || tp->chip_id == DC21142 ||
540 tp->chip_id == MX98713 || tp->chip_id == COMPEX9881 ||
541 tp->chip_id == DM910X) {
542 dev_warn(&dev->dev,
543 "21140 transmit timed out, status %08x, SIA %08x %08x %08x %08x, resetting...\n",
544 ioread32(ioaddr + CSR5), ioread32(ioaddr + CSR12),
545 ioread32(ioaddr + CSR13), ioread32(ioaddr + CSR14),
546 ioread32(ioaddr + CSR15));
547 tp->timeout_recovery = 1;
548 schedule_work(&tp->media_work);
549 goto out_unlock;
550 } else if (tp->chip_id == PNIC2) {
551 dev_warn(&dev->dev,
552 "PNIC2 transmit timed out, status %08x, CSR6/7 %08x / %08x CSR12 %08x, resetting...\n",
553 (int)ioread32(ioaddr + CSR5),
554 (int)ioread32(ioaddr + CSR6),
555 (int)ioread32(ioaddr + CSR7),
556 (int)ioread32(ioaddr + CSR12));
557 } else {
558 dev_warn(&dev->dev,
559 "Transmit timed out, status %08x, CSR12 %08x, resetting...\n",
560 ioread32(ioaddr + CSR5), ioread32(ioaddr + CSR12));
561 dev->if_port = 0;
564 #if defined(way_too_many_messages)
565 if (tulip_debug > 3) {
566 int i;
567 for (i = 0; i < RX_RING_SIZE; i++) {
568 u8 *buf = (u8 *)(tp->rx_ring[i].buffer1);
569 int j;
570 printk(KERN_DEBUG
571 "%2d: %08x %08x %08x %08x %02x %02x %02x\n",
573 (unsigned int)tp->rx_ring[i].status,
574 (unsigned int)tp->rx_ring[i].length,
575 (unsigned int)tp->rx_ring[i].buffer1,
576 (unsigned int)tp->rx_ring[i].buffer2,
577 buf[0], buf[1], buf[2]);
578 for (j = 0; ((j < 1600) && buf[j] != 0xee); j++)
579 if (j < 100)
580 pr_cont(" %02x", buf[j]);
581 pr_cont(" j=%d\n", j);
583 printk(KERN_DEBUG " Rx ring %p: ", tp->rx_ring);
584 for (i = 0; i < RX_RING_SIZE; i++)
585 pr_cont(" %08x", (unsigned int)tp->rx_ring[i].status);
586 printk(KERN_DEBUG " Tx ring %p: ", tp->tx_ring);
587 for (i = 0; i < TX_RING_SIZE; i++)
588 pr_cont(" %08x", (unsigned int)tp->tx_ring[i].status);
589 pr_cont("\n");
591 #endif
593 tulip_tx_timeout_complete(tp, ioaddr);
595 out_unlock:
596 spin_unlock_irqrestore (&tp->lock, flags);
597 netif_trans_update(dev); /* prevent tx timeout */
598 netif_wake_queue (dev);
602 /* Initialize the Rx and Tx rings, along with various 'dev' bits. */
603 static void tulip_init_ring(struct net_device *dev)
605 struct tulip_private *tp = netdev_priv(dev);
606 int i;
608 tp->susp_rx = 0;
609 tp->ttimer = 0;
610 tp->nir = 0;
612 for (i = 0; i < RX_RING_SIZE; i++) {
613 tp->rx_ring[i].status = 0x00000000;
614 tp->rx_ring[i].length = cpu_to_le32(PKT_BUF_SZ);
615 tp->rx_ring[i].buffer2 = cpu_to_le32(tp->rx_ring_dma + sizeof(struct tulip_rx_desc) * (i + 1));
616 tp->rx_buffers[i].skb = NULL;
617 tp->rx_buffers[i].mapping = 0;
619 /* Mark the last entry as wrapping the ring. */
620 tp->rx_ring[i-1].length = cpu_to_le32(PKT_BUF_SZ | DESC_RING_WRAP);
621 tp->rx_ring[i-1].buffer2 = cpu_to_le32(tp->rx_ring_dma);
623 for (i = 0; i < RX_RING_SIZE; i++) {
624 dma_addr_t mapping;
626 /* Note the receive buffer must be longword aligned.
627 netdev_alloc_skb() provides 16 byte alignment. But do *not*
628 use skb_reserve() to align the IP header! */
629 struct sk_buff *skb = netdev_alloc_skb(dev, PKT_BUF_SZ);
630 tp->rx_buffers[i].skb = skb;
631 if (skb == NULL)
632 break;
633 mapping = dma_map_single(&tp->pdev->dev, skb->data,
634 PKT_BUF_SZ, DMA_FROM_DEVICE);
635 tp->rx_buffers[i].mapping = mapping;
636 tp->rx_ring[i].status = cpu_to_le32(DescOwned); /* Owned by Tulip chip */
637 tp->rx_ring[i].buffer1 = cpu_to_le32(mapping);
639 tp->dirty_rx = (unsigned int)(i - RX_RING_SIZE);
641 /* The Tx buffer descriptor is filled in as needed, but we
642 do need to clear the ownership bit. */
643 for (i = 0; i < TX_RING_SIZE; i++) {
644 tp->tx_buffers[i].skb = NULL;
645 tp->tx_buffers[i].mapping = 0;
646 tp->tx_ring[i].status = 0x00000000;
647 tp->tx_ring[i].buffer2 = cpu_to_le32(tp->tx_ring_dma + sizeof(struct tulip_tx_desc) * (i + 1));
649 tp->tx_ring[i-1].buffer2 = cpu_to_le32(tp->tx_ring_dma);
652 static netdev_tx_t
653 tulip_start_xmit(struct sk_buff *skb, struct net_device *dev)
655 struct tulip_private *tp = netdev_priv(dev);
656 int entry;
657 u32 flag;
658 dma_addr_t mapping;
659 unsigned long flags;
661 spin_lock_irqsave(&tp->lock, flags);
663 /* Calculate the next Tx descriptor entry. */
664 entry = tp->cur_tx % TX_RING_SIZE;
666 tp->tx_buffers[entry].skb = skb;
667 mapping = dma_map_single(&tp->pdev->dev, skb->data, skb->len,
668 DMA_TO_DEVICE);
669 tp->tx_buffers[entry].mapping = mapping;
670 tp->tx_ring[entry].buffer1 = cpu_to_le32(mapping);
672 if (tp->cur_tx - tp->dirty_tx < TX_RING_SIZE/2) {/* Typical path */
673 flag = 0x60000000; /* No interrupt */
674 } else if (tp->cur_tx - tp->dirty_tx == TX_RING_SIZE/2) {
675 flag = 0xe0000000; /* Tx-done intr. */
676 } else if (tp->cur_tx - tp->dirty_tx < TX_RING_SIZE - 2) {
677 flag = 0x60000000; /* No Tx-done intr. */
678 } else { /* Leave room for set_rx_mode() to fill entries. */
679 flag = 0xe0000000; /* Tx-done intr. */
680 netif_stop_queue(dev);
682 if (entry == TX_RING_SIZE-1)
683 flag = 0xe0000000 | DESC_RING_WRAP;
685 tp->tx_ring[entry].length = cpu_to_le32(skb->len | flag);
686 /* if we were using Transmit Automatic Polling, we would need a
687 * wmb() here. */
688 tp->tx_ring[entry].status = cpu_to_le32(DescOwned);
689 wmb();
691 tp->cur_tx++;
693 /* Trigger an immediate transmit demand. */
694 iowrite32(0, tp->base_addr + CSR1);
696 spin_unlock_irqrestore(&tp->lock, flags);
698 return NETDEV_TX_OK;
701 static void tulip_clean_tx_ring(struct tulip_private *tp)
703 unsigned int dirty_tx;
705 for (dirty_tx = tp->dirty_tx ; tp->cur_tx - dirty_tx > 0;
706 dirty_tx++) {
707 int entry = dirty_tx % TX_RING_SIZE;
708 int status = le32_to_cpu(tp->tx_ring[entry].status);
710 if (status < 0) {
711 tp->dev->stats.tx_errors++; /* It wasn't Txed */
712 tp->tx_ring[entry].status = 0;
715 /* Check for Tx filter setup frames. */
716 if (tp->tx_buffers[entry].skb == NULL) {
717 /* test because dummy frames not mapped */
718 if (tp->tx_buffers[entry].mapping)
719 dma_unmap_single(&tp->pdev->dev,
720 tp->tx_buffers[entry].mapping,
721 sizeof(tp->setup_frame),
722 DMA_TO_DEVICE);
723 continue;
726 dma_unmap_single(&tp->pdev->dev,
727 tp->tx_buffers[entry].mapping,
728 tp->tx_buffers[entry].skb->len,
729 DMA_TO_DEVICE);
731 /* Free the original skb. */
732 dev_kfree_skb_irq(tp->tx_buffers[entry].skb);
733 tp->tx_buffers[entry].skb = NULL;
734 tp->tx_buffers[entry].mapping = 0;
738 static void tulip_down (struct net_device *dev)
740 struct tulip_private *tp = netdev_priv(dev);
741 void __iomem *ioaddr = tp->base_addr;
742 unsigned long flags;
744 cancel_work_sync(&tp->media_work);
746 #ifdef CONFIG_TULIP_NAPI
747 napi_disable(&tp->napi);
748 #endif
750 del_timer_sync (&tp->timer);
751 #ifdef CONFIG_TULIP_NAPI
752 del_timer_sync (&tp->oom_timer);
753 #endif
754 spin_lock_irqsave (&tp->lock, flags);
756 /* Disable interrupts by clearing the interrupt mask. */
757 iowrite32 (0x00000000, ioaddr + CSR7);
759 /* Stop the Tx and Rx processes. */
760 tulip_stop_rxtx(tp);
762 /* prepare receive buffers */
763 tulip_refill_rx(dev);
765 /* release any unconsumed transmit buffers */
766 tulip_clean_tx_ring(tp);
768 if (ioread32(ioaddr + CSR6) != 0xffffffff)
769 dev->stats.rx_missed_errors += ioread32(ioaddr + CSR8) & 0xffff;
771 spin_unlock_irqrestore (&tp->lock, flags);
773 timer_setup(&tp->timer, tulip_tbl[tp->chip_id].media_timer, 0);
775 dev->if_port = tp->saved_if_port;
777 /* Leave the driver in snooze, not sleep, mode. */
778 tulip_set_power_state (tp, 0, 1);
781 static void tulip_free_ring (struct net_device *dev)
783 struct tulip_private *tp = netdev_priv(dev);
784 int i;
786 /* Free all the skbuffs in the Rx queue. */
787 for (i = 0; i < RX_RING_SIZE; i++) {
788 struct sk_buff *skb = tp->rx_buffers[i].skb;
789 dma_addr_t mapping = tp->rx_buffers[i].mapping;
791 tp->rx_buffers[i].skb = NULL;
792 tp->rx_buffers[i].mapping = 0;
794 tp->rx_ring[i].status = 0; /* Not owned by Tulip chip. */
795 tp->rx_ring[i].length = 0;
796 /* An invalid address. */
797 tp->rx_ring[i].buffer1 = cpu_to_le32(0xBADF00D0);
798 if (skb) {
799 dma_unmap_single(&tp->pdev->dev, mapping, PKT_BUF_SZ,
800 DMA_FROM_DEVICE);
801 dev_kfree_skb (skb);
805 for (i = 0; i < TX_RING_SIZE; i++) {
806 struct sk_buff *skb = tp->tx_buffers[i].skb;
808 if (skb != NULL) {
809 dma_unmap_single(&tp->pdev->dev,
810 tp->tx_buffers[i].mapping, skb->len,
811 DMA_TO_DEVICE);
812 dev_kfree_skb (skb);
814 tp->tx_buffers[i].skb = NULL;
815 tp->tx_buffers[i].mapping = 0;
819 static int tulip_close (struct net_device *dev)
821 struct tulip_private *tp = netdev_priv(dev);
822 void __iomem *ioaddr = tp->base_addr;
824 netif_stop_queue (dev);
826 tulip_down (dev);
828 if (tulip_debug > 1)
829 netdev_dbg(dev, "Shutting down ethercard, status was %02x\n",
830 ioread32 (ioaddr + CSR5));
832 free_irq (tp->pdev->irq, dev);
834 tulip_free_ring (dev);
836 return 0;
839 static struct net_device_stats *tulip_get_stats(struct net_device *dev)
841 struct tulip_private *tp = netdev_priv(dev);
842 void __iomem *ioaddr = tp->base_addr;
844 if (netif_running(dev)) {
845 unsigned long flags;
847 spin_lock_irqsave (&tp->lock, flags);
849 dev->stats.rx_missed_errors += ioread32(ioaddr + CSR8) & 0xffff;
851 spin_unlock_irqrestore(&tp->lock, flags);
854 return &dev->stats;
858 static void tulip_get_drvinfo(struct net_device *dev, struct ethtool_drvinfo *info)
860 struct tulip_private *np = netdev_priv(dev);
861 strlcpy(info->driver, DRV_NAME, sizeof(info->driver));
862 strlcpy(info->bus_info, pci_name(np->pdev), sizeof(info->bus_info));
866 static int tulip_ethtool_set_wol(struct net_device *dev,
867 struct ethtool_wolinfo *wolinfo)
869 struct tulip_private *tp = netdev_priv(dev);
871 if (wolinfo->wolopts & (~tp->wolinfo.supported))
872 return -EOPNOTSUPP;
874 tp->wolinfo.wolopts = wolinfo->wolopts;
875 device_set_wakeup_enable(&tp->pdev->dev, tp->wolinfo.wolopts);
876 return 0;
879 static void tulip_ethtool_get_wol(struct net_device *dev,
880 struct ethtool_wolinfo *wolinfo)
882 struct tulip_private *tp = netdev_priv(dev);
884 wolinfo->supported = tp->wolinfo.supported;
885 wolinfo->wolopts = tp->wolinfo.wolopts;
886 return;
890 static const struct ethtool_ops ops = {
891 .get_drvinfo = tulip_get_drvinfo,
892 .set_wol = tulip_ethtool_set_wol,
893 .get_wol = tulip_ethtool_get_wol,
896 /* Provide ioctl() calls to examine the MII xcvr state. */
897 static int private_ioctl (struct net_device *dev, struct ifreq *rq, int cmd)
899 struct tulip_private *tp = netdev_priv(dev);
900 void __iomem *ioaddr = tp->base_addr;
901 struct mii_ioctl_data *data = if_mii(rq);
902 const unsigned int phy_idx = 0;
903 int phy = tp->phys[phy_idx] & 0x1f;
904 unsigned int regnum = data->reg_num;
906 switch (cmd) {
907 case SIOCGMIIPHY: /* Get address of MII PHY in use. */
908 if (tp->mii_cnt)
909 data->phy_id = phy;
910 else if (tp->flags & HAS_NWAY)
911 data->phy_id = 32;
912 else if (tp->chip_id == COMET)
913 data->phy_id = 1;
914 else
915 return -ENODEV;
916 fallthrough;
918 case SIOCGMIIREG: /* Read MII PHY register. */
919 if (data->phy_id == 32 && (tp->flags & HAS_NWAY)) {
920 int csr12 = ioread32 (ioaddr + CSR12);
921 int csr14 = ioread32 (ioaddr + CSR14);
922 switch (regnum) {
923 case 0:
924 if (((csr14<<5) & 0x1000) ||
925 (dev->if_port == 5 && tp->nwayset))
926 data->val_out = 0x1000;
927 else
928 data->val_out = (tulip_media_cap[dev->if_port]&MediaIs100 ? 0x2000 : 0)
929 | (tulip_media_cap[dev->if_port]&MediaIsFD ? 0x0100 : 0);
930 break;
931 case 1:
932 data->val_out =
933 0x1848 +
934 ((csr12&0x7000) == 0x5000 ? 0x20 : 0) +
935 ((csr12&0x06) == 6 ? 0 : 4);
936 data->val_out |= 0x6048;
937 break;
938 case 4:
939 /* Advertised value, bogus 10baseTx-FD value from CSR6. */
940 data->val_out =
941 ((ioread32(ioaddr + CSR6) >> 3) & 0x0040) +
942 ((csr14 >> 1) & 0x20) + 1;
943 data->val_out |= ((csr14 >> 9) & 0x03C0);
944 break;
945 case 5: data->val_out = tp->lpar; break;
946 default: data->val_out = 0; break;
948 } else {
949 data->val_out = tulip_mdio_read (dev, data->phy_id & 0x1f, regnum);
951 return 0;
953 case SIOCSMIIREG: /* Write MII PHY register. */
954 if (regnum & ~0x1f)
955 return -EINVAL;
956 if (data->phy_id == phy) {
957 u16 value = data->val_in;
958 switch (regnum) {
959 case 0: /* Check for autonegotiation on or reset. */
960 tp->full_duplex_lock = (value & 0x9000) ? 0 : 1;
961 if (tp->full_duplex_lock)
962 tp->full_duplex = (value & 0x0100) ? 1 : 0;
963 break;
964 case 4:
965 tp->advertising[phy_idx] =
966 tp->mii_advertise = data->val_in;
967 break;
970 if (data->phy_id == 32 && (tp->flags & HAS_NWAY)) {
971 u16 value = data->val_in;
972 if (regnum == 0) {
973 if ((value & 0x1200) == 0x1200) {
974 if (tp->chip_id == PNIC2) {
975 pnic2_start_nway (dev);
976 } else {
977 t21142_start_nway (dev);
980 } else if (regnum == 4)
981 tp->sym_advertise = value;
982 } else {
983 tulip_mdio_write (dev, data->phy_id & 0x1f, regnum, data->val_in);
985 return 0;
986 default:
987 return -EOPNOTSUPP;
990 return -EOPNOTSUPP;
994 /* Set or clear the multicast filter for this adaptor.
995 Note that we only use exclusion around actually queueing the
996 new frame, not around filling tp->setup_frame. This is non-deterministic
997 when re-entered but still correct. */
999 static void build_setup_frame_hash(u16 *setup_frm, struct net_device *dev)
1001 struct tulip_private *tp = netdev_priv(dev);
1002 u16 hash_table[32];
1003 struct netdev_hw_addr *ha;
1004 int i;
1005 u16 *eaddrs;
1007 memset(hash_table, 0, sizeof(hash_table));
1008 __set_bit_le(255, hash_table); /* Broadcast entry */
1009 /* This should work on big-endian machines as well. */
1010 netdev_for_each_mc_addr(ha, dev) {
1011 int index = ether_crc_le(ETH_ALEN, ha->addr) & 0x1ff;
1013 __set_bit_le(index, hash_table);
1015 for (i = 0; i < 32; i++) {
1016 *setup_frm++ = hash_table[i];
1017 *setup_frm++ = hash_table[i];
1019 setup_frm = &tp->setup_frame[13*6];
1021 /* Fill the final entry with our physical address. */
1022 eaddrs = (u16 *)dev->dev_addr;
1023 *setup_frm++ = eaddrs[0]; *setup_frm++ = eaddrs[0];
1024 *setup_frm++ = eaddrs[1]; *setup_frm++ = eaddrs[1];
1025 *setup_frm++ = eaddrs[2]; *setup_frm++ = eaddrs[2];
1028 static void build_setup_frame_perfect(u16 *setup_frm, struct net_device *dev)
1030 struct tulip_private *tp = netdev_priv(dev);
1031 struct netdev_hw_addr *ha;
1032 u16 *eaddrs;
1034 /* We have <= 14 addresses so we can use the wonderful
1035 16 address perfect filtering of the Tulip. */
1036 netdev_for_each_mc_addr(ha, dev) {
1037 eaddrs = (u16 *) ha->addr;
1038 *setup_frm++ = *eaddrs; *setup_frm++ = *eaddrs++;
1039 *setup_frm++ = *eaddrs; *setup_frm++ = *eaddrs++;
1040 *setup_frm++ = *eaddrs; *setup_frm++ = *eaddrs++;
1042 /* Fill the unused entries with the broadcast address. */
1043 memset(setup_frm, 0xff, (15 - netdev_mc_count(dev)) * 12);
1044 setup_frm = &tp->setup_frame[15*6];
1046 /* Fill the final entry with our physical address. */
1047 eaddrs = (u16 *)dev->dev_addr;
1048 *setup_frm++ = eaddrs[0]; *setup_frm++ = eaddrs[0];
1049 *setup_frm++ = eaddrs[1]; *setup_frm++ = eaddrs[1];
1050 *setup_frm++ = eaddrs[2]; *setup_frm++ = eaddrs[2];
1054 static void set_rx_mode(struct net_device *dev)
1056 struct tulip_private *tp = netdev_priv(dev);
1057 void __iomem *ioaddr = tp->base_addr;
1058 int csr6;
1060 csr6 = ioread32(ioaddr + CSR6) & ~0x00D5;
1062 tp->csr6 &= ~0x00D5;
1063 if (dev->flags & IFF_PROMISC) { /* Set promiscuous. */
1064 tp->csr6 |= AcceptAllMulticast | AcceptAllPhys;
1065 csr6 |= AcceptAllMulticast | AcceptAllPhys;
1066 } else if ((netdev_mc_count(dev) > 1000) ||
1067 (dev->flags & IFF_ALLMULTI)) {
1068 /* Too many to filter well -- accept all multicasts. */
1069 tp->csr6 |= AcceptAllMulticast;
1070 csr6 |= AcceptAllMulticast;
1071 } else if (tp->flags & MC_HASH_ONLY) {
1072 /* Some work-alikes have only a 64-entry hash filter table. */
1073 /* Should verify correctness on big-endian/__powerpc__ */
1074 struct netdev_hw_addr *ha;
1075 if (netdev_mc_count(dev) > 64) {
1076 /* Arbitrary non-effective limit. */
1077 tp->csr6 |= AcceptAllMulticast;
1078 csr6 |= AcceptAllMulticast;
1079 } else {
1080 u32 mc_filter[2] = {0, 0}; /* Multicast hash filter */
1081 int filterbit;
1082 netdev_for_each_mc_addr(ha, dev) {
1083 if (tp->flags & COMET_MAC_ADDR)
1084 filterbit = ether_crc_le(ETH_ALEN,
1085 ha->addr);
1086 else
1087 filterbit = ether_crc(ETH_ALEN,
1088 ha->addr) >> 26;
1089 filterbit &= 0x3f;
1090 mc_filter[filterbit >> 5] |= 1 << (filterbit & 31);
1091 if (tulip_debug > 2)
1092 dev_info(&dev->dev,
1093 "Added filter for %pM %08x bit %d\n",
1094 ha->addr,
1095 ether_crc(ETH_ALEN, ha->addr),
1096 filterbit);
1098 if (mc_filter[0] == tp->mc_filter[0] &&
1099 mc_filter[1] == tp->mc_filter[1])
1100 ; /* No change. */
1101 else if (tp->flags & IS_ASIX) {
1102 iowrite32(2, ioaddr + CSR13);
1103 iowrite32(mc_filter[0], ioaddr + CSR14);
1104 iowrite32(3, ioaddr + CSR13);
1105 iowrite32(mc_filter[1], ioaddr + CSR14);
1106 } else if (tp->flags & COMET_MAC_ADDR) {
1107 iowrite32(mc_filter[0], ioaddr + CSR27);
1108 iowrite32(mc_filter[1], ioaddr + CSR28);
1110 tp->mc_filter[0] = mc_filter[0];
1111 tp->mc_filter[1] = mc_filter[1];
1113 } else {
1114 unsigned long flags;
1115 u32 tx_flags = 0x08000000 | 192;
1117 /* Note that only the low-address shortword of setup_frame is valid!
1118 The values are doubled for big-endian architectures. */
1119 if (netdev_mc_count(dev) > 14) {
1120 /* Must use a multicast hash table. */
1121 build_setup_frame_hash(tp->setup_frame, dev);
1122 tx_flags = 0x08400000 | 192;
1123 } else {
1124 build_setup_frame_perfect(tp->setup_frame, dev);
1127 spin_lock_irqsave(&tp->lock, flags);
1129 if (tp->cur_tx - tp->dirty_tx > TX_RING_SIZE - 2) {
1130 /* Same setup recently queued, we need not add it. */
1131 } else {
1132 unsigned int entry;
1133 int dummy = -1;
1135 /* Now add this frame to the Tx list. */
1137 entry = tp->cur_tx++ % TX_RING_SIZE;
1139 if (entry != 0) {
1140 /* Avoid a chip errata by prefixing a dummy entry. */
1141 tp->tx_buffers[entry].skb = NULL;
1142 tp->tx_buffers[entry].mapping = 0;
1143 tp->tx_ring[entry].length =
1144 (entry == TX_RING_SIZE-1) ? cpu_to_le32(DESC_RING_WRAP) : 0;
1145 tp->tx_ring[entry].buffer1 = 0;
1146 /* Must set DescOwned later to avoid race with chip */
1147 dummy = entry;
1148 entry = tp->cur_tx++ % TX_RING_SIZE;
1152 tp->tx_buffers[entry].skb = NULL;
1153 tp->tx_buffers[entry].mapping =
1154 dma_map_single(&tp->pdev->dev,
1155 tp->setup_frame,
1156 sizeof(tp->setup_frame),
1157 DMA_TO_DEVICE);
1158 /* Put the setup frame on the Tx list. */
1159 if (entry == TX_RING_SIZE-1)
1160 tx_flags |= DESC_RING_WRAP; /* Wrap ring. */
1161 tp->tx_ring[entry].length = cpu_to_le32(tx_flags);
1162 tp->tx_ring[entry].buffer1 =
1163 cpu_to_le32(tp->tx_buffers[entry].mapping);
1164 tp->tx_ring[entry].status = cpu_to_le32(DescOwned);
1165 if (dummy >= 0)
1166 tp->tx_ring[dummy].status = cpu_to_le32(DescOwned);
1167 if (tp->cur_tx - tp->dirty_tx >= TX_RING_SIZE - 2)
1168 netif_stop_queue(dev);
1170 /* Trigger an immediate transmit demand. */
1171 iowrite32(0, ioaddr + CSR1);
1174 spin_unlock_irqrestore(&tp->lock, flags);
1177 iowrite32(csr6, ioaddr + CSR6);
1180 #ifdef CONFIG_TULIP_MWI
1181 static void tulip_mwi_config(struct pci_dev *pdev, struct net_device *dev)
1183 struct tulip_private *tp = netdev_priv(dev);
1184 u8 cache;
1185 u16 pci_command;
1186 u32 csr0;
1188 if (tulip_debug > 3)
1189 netdev_dbg(dev, "tulip_mwi_config()\n");
1191 tp->csr0 = csr0 = 0;
1193 /* if we have any cache line size at all, we can do MRM and MWI */
1194 csr0 |= MRM | MWI;
1196 /* Enable MWI in the standard PCI command bit.
1197 * Check for the case where MWI is desired but not available
1199 pci_try_set_mwi(pdev);
1201 /* read result from hardware (in case bit refused to enable) */
1202 pci_read_config_word(pdev, PCI_COMMAND, &pci_command);
1203 if ((csr0 & MWI) && (!(pci_command & PCI_COMMAND_INVALIDATE)))
1204 csr0 &= ~MWI;
1206 /* if cache line size hardwired to zero, no MWI */
1207 pci_read_config_byte(pdev, PCI_CACHE_LINE_SIZE, &cache);
1208 if ((csr0 & MWI) && (cache == 0)) {
1209 csr0 &= ~MWI;
1210 pci_clear_mwi(pdev);
1213 /* assign per-cacheline-size cache alignment and
1214 * burst length values
1216 switch (cache) {
1217 case 8:
1218 csr0 |= MRL | (1 << CALShift) | (16 << BurstLenShift);
1219 break;
1220 case 16:
1221 csr0 |= MRL | (2 << CALShift) | (16 << BurstLenShift);
1222 break;
1223 case 32:
1224 csr0 |= MRL | (3 << CALShift) | (32 << BurstLenShift);
1225 break;
1226 default:
1227 cache = 0;
1228 break;
1231 /* if we have a good cache line size, we by now have a good
1232 * csr0, so save it and exit
1234 if (cache)
1235 goto out;
1237 /* we don't have a good csr0 or cache line size, disable MWI */
1238 if (csr0 & MWI) {
1239 pci_clear_mwi(pdev);
1240 csr0 &= ~MWI;
1243 /* sane defaults for burst length and cache alignment
1244 * originally from de4x5 driver
1246 csr0 |= (8 << BurstLenShift) | (1 << CALShift);
1248 out:
1249 tp->csr0 = csr0;
1250 if (tulip_debug > 2)
1251 netdev_dbg(dev, "MWI config cacheline=%d, csr0=%08x\n",
1252 cache, csr0);
1254 #endif
1257 * Chips that have the MRM/reserved bit quirk and the burst quirk. That
1258 * is the DM910X and the on chip ULi devices
1261 static int tulip_uli_dm_quirk(struct pci_dev *pdev)
1263 if (pdev->vendor == 0x1282 && pdev->device == 0x9102)
1264 return 1;
1265 return 0;
1268 static const struct net_device_ops tulip_netdev_ops = {
1269 .ndo_open = tulip_open,
1270 .ndo_start_xmit = tulip_start_xmit,
1271 .ndo_tx_timeout = tulip_tx_timeout,
1272 .ndo_stop = tulip_close,
1273 .ndo_get_stats = tulip_get_stats,
1274 .ndo_do_ioctl = private_ioctl,
1275 .ndo_set_rx_mode = set_rx_mode,
1276 .ndo_set_mac_address = eth_mac_addr,
1277 .ndo_validate_addr = eth_validate_addr,
1278 #ifdef CONFIG_NET_POLL_CONTROLLER
1279 .ndo_poll_controller = poll_tulip,
1280 #endif
1283 static const struct pci_device_id early_486_chipsets[] = {
1284 { PCI_DEVICE(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82424) },
1285 { PCI_DEVICE(PCI_VENDOR_ID_SI, PCI_DEVICE_ID_SI_496) },
1286 { },
1289 static int tulip_init_one(struct pci_dev *pdev, const struct pci_device_id *ent)
1291 struct tulip_private *tp;
1292 /* See note below on the multiport cards. */
1293 static unsigned char last_phys_addr[ETH_ALEN] = {
1294 0x00, 'L', 'i', 'n', 'u', 'x'
1296 #if defined(__i386__) || defined(__x86_64__) /* Patch up x86 BIOS bug. */
1297 static int last_irq;
1298 #endif
1299 int i, irq;
1300 unsigned short sum;
1301 unsigned char *ee_data;
1302 struct net_device *dev;
1303 void __iomem *ioaddr;
1304 static int board_idx = -1;
1305 int chip_idx = ent->driver_data;
1306 const char *chip_name = tulip_tbl[chip_idx].chip_name;
1307 unsigned int eeprom_missing = 0;
1308 unsigned int force_csr0 = 0;
1310 board_idx++;
1313 * Lan media wire a tulip chip to a wan interface. Needs a very
1314 * different driver (lmc driver)
1317 if (pdev->subsystem_vendor == PCI_VENDOR_ID_LMC) {
1318 pr_err("skipping LMC card\n");
1319 return -ENODEV;
1320 } else if (pdev->subsystem_vendor == PCI_VENDOR_ID_SBE &&
1321 (pdev->subsystem_device == PCI_SUBDEVICE_ID_SBE_T3E3 ||
1322 pdev->subsystem_device == PCI_SUBDEVICE_ID_SBE_2T3E3_P0 ||
1323 pdev->subsystem_device == PCI_SUBDEVICE_ID_SBE_2T3E3_P1)) {
1324 pr_err("skipping SBE T3E3 port\n");
1325 return -ENODEV;
1329 * DM910x chips should be handled by the dmfe driver, except
1330 * on-board chips on SPARC systems. Also, early DM9100s need
1331 * software CRC which only the dmfe driver supports.
1334 #ifdef CONFIG_TULIP_DM910X
1335 if (chip_idx == DM910X) {
1336 struct device_node *dp;
1338 if (pdev->vendor == 0x1282 && pdev->device == 0x9100 &&
1339 pdev->revision < 0x30) {
1340 pr_info("skipping early DM9100 with Crc bug (use dmfe)\n");
1341 return -ENODEV;
1344 dp = pci_device_to_OF_node(pdev);
1345 if (!(dp && of_get_property(dp, "local-mac-address", NULL))) {
1346 pr_info("skipping DM910x expansion card (use dmfe)\n");
1347 return -ENODEV;
1350 #endif
1353 * Looks for early PCI chipsets where people report hangs
1354 * without the workarounds being on.
1357 /* 1. Intel Saturn. Switch to 8 long words burst, 8 long word cache
1358 aligned. Aries might need this too. The Saturn errata are not
1359 pretty reading but thankfully it's an old 486 chipset.
1361 2. The dreaded SiS496 486 chipset. Same workaround as Intel
1362 Saturn.
1365 if (pci_dev_present(early_486_chipsets)) {
1366 csr0 = MRL | MRM | (8 << BurstLenShift) | (1 << CALShift);
1367 force_csr0 = 1;
1370 /* bugfix: the ASIX must have a burst limit or horrible things happen. */
1371 if (chip_idx == AX88140) {
1372 if ((csr0 & 0x3f00) == 0)
1373 csr0 |= 0x2000;
1376 /* PNIC doesn't have MWI/MRL/MRM... */
1377 if (chip_idx == LC82C168)
1378 csr0 &= ~0xfff10000; /* zero reserved bits 31:20, 16 */
1380 /* DM9102A has troubles with MRM & clear reserved bits 24:22, 20, 16, 7:1 */
1381 if (tulip_uli_dm_quirk(pdev)) {
1382 csr0 &= ~0x01f100ff;
1383 #if defined(CONFIG_SPARC)
1384 csr0 = (csr0 & ~0xff00) | 0xe000;
1385 #endif
1388 * And back to business
1391 i = pci_enable_device(pdev);
1392 if (i) {
1393 pr_err("Cannot enable tulip board #%d, aborting\n", board_idx);
1394 return i;
1397 irq = pdev->irq;
1399 /* alloc_etherdev ensures aligned and zeroed private structures */
1400 dev = alloc_etherdev (sizeof (*tp));
1401 if (!dev)
1402 return -ENOMEM;
1404 SET_NETDEV_DEV(dev, &pdev->dev);
1405 if (pci_resource_len (pdev, 0) < tulip_tbl[chip_idx].io_size) {
1406 pr_err("%s: I/O region (0x%llx@0x%llx) too small, aborting\n",
1407 pci_name(pdev),
1408 (unsigned long long)pci_resource_len (pdev, 0),
1409 (unsigned long long)pci_resource_start (pdev, 0));
1410 goto err_out_free_netdev;
1413 /* grab all resources from both PIO and MMIO regions, as we
1414 * don't want anyone else messing around with our hardware */
1415 if (pci_request_regions (pdev, DRV_NAME))
1416 goto err_out_free_netdev;
1418 ioaddr = pci_iomap(pdev, TULIP_BAR, tulip_tbl[chip_idx].io_size);
1420 if (!ioaddr)
1421 goto err_out_free_res;
1424 * initialize private data structure 'tp'
1425 * it is zeroed and aligned in alloc_etherdev
1427 tp = netdev_priv(dev);
1428 tp->dev = dev;
1430 tp->rx_ring = dma_alloc_coherent(&pdev->dev,
1431 sizeof(struct tulip_rx_desc) * RX_RING_SIZE +
1432 sizeof(struct tulip_tx_desc) * TX_RING_SIZE,
1433 &tp->rx_ring_dma, GFP_KERNEL);
1434 if (!tp->rx_ring)
1435 goto err_out_mtable;
1436 tp->tx_ring = (struct tulip_tx_desc *)(tp->rx_ring + RX_RING_SIZE);
1437 tp->tx_ring_dma = tp->rx_ring_dma + sizeof(struct tulip_rx_desc) * RX_RING_SIZE;
1439 tp->chip_id = chip_idx;
1440 tp->flags = tulip_tbl[chip_idx].flags;
1442 tp->wolinfo.supported = 0;
1443 tp->wolinfo.wolopts = 0;
1444 /* COMET: Enable power management only for AN983B */
1445 if (chip_idx == COMET ) {
1446 u32 sig;
1447 pci_read_config_dword (pdev, 0x80, &sig);
1448 if (sig == 0x09811317) {
1449 tp->flags |= COMET_PM;
1450 tp->wolinfo.supported = WAKE_PHY | WAKE_MAGIC;
1451 pr_info("%s: Enabled WOL support for AN983B\n",
1452 __func__);
1455 tp->pdev = pdev;
1456 tp->base_addr = ioaddr;
1457 tp->revision = pdev->revision;
1458 tp->csr0 = csr0;
1459 spin_lock_init(&tp->lock);
1460 spin_lock_init(&tp->mii_lock);
1461 timer_setup(&tp->timer, tulip_tbl[tp->chip_id].media_timer, 0);
1463 INIT_WORK(&tp->media_work, tulip_tbl[tp->chip_id].media_task);
1465 #ifdef CONFIG_TULIP_MWI
1466 if (!force_csr0 && (tp->flags & HAS_PCI_MWI))
1467 tulip_mwi_config (pdev, dev);
1468 #endif
1470 /* Stop the chip's Tx and Rx processes. */
1471 tulip_stop_rxtx(tp);
1473 pci_set_master(pdev);
1475 #ifdef CONFIG_GSC
1476 if (pdev->subsystem_vendor == PCI_VENDOR_ID_HP) {
1477 switch (pdev->subsystem_device) {
1478 default:
1479 break;
1480 case 0x1061:
1481 case 0x1062:
1482 case 0x1063:
1483 case 0x1098:
1484 case 0x1099:
1485 case 0x10EE:
1486 tp->flags |= HAS_SWAPPED_SEEPROM | NEEDS_FAKE_MEDIA_TABLE;
1487 chip_name = "GSC DS21140 Tulip";
1490 #endif
1492 /* Clear the missed-packet counter. */
1493 ioread32(ioaddr + CSR8);
1495 /* The station address ROM is read byte serially. The register must
1496 be polled, waiting for the value to be read bit serially from the
1497 EEPROM.
1499 ee_data = tp->eeprom;
1500 memset(ee_data, 0, sizeof(tp->eeprom));
1501 sum = 0;
1502 if (chip_idx == LC82C168) {
1503 for (i = 0; i < 3; i++) {
1504 int value, boguscnt = 100000;
1505 iowrite32(0x600 | i, ioaddr + 0x98);
1506 do {
1507 value = ioread32(ioaddr + CSR9);
1508 } while (value < 0 && --boguscnt > 0);
1509 put_unaligned_le16(value, ((__le16 *)dev->dev_addr) + i);
1510 sum += value & 0xffff;
1512 } else if (chip_idx == COMET) {
1513 /* No need to read the EEPROM. */
1514 put_unaligned_le32(ioread32(ioaddr + 0xA4), dev->dev_addr);
1515 put_unaligned_le16(ioread32(ioaddr + 0xA8), dev->dev_addr + 4);
1516 for (i = 0; i < 6; i ++)
1517 sum += dev->dev_addr[i];
1518 } else {
1519 /* A serial EEPROM interface, we read now and sort it out later. */
1520 int sa_offset = 0;
1521 int ee_addr_size = tulip_read_eeprom(dev, 0xff, 8) & 0x40000 ? 8 : 6;
1522 int ee_max_addr = ((1 << ee_addr_size) - 1) * sizeof(u16);
1524 if (ee_max_addr > sizeof(tp->eeprom))
1525 ee_max_addr = sizeof(tp->eeprom);
1527 for (i = 0; i < ee_max_addr ; i += sizeof(u16)) {
1528 u16 data = tulip_read_eeprom(dev, i/2, ee_addr_size);
1529 ee_data[i] = data & 0xff;
1530 ee_data[i + 1] = data >> 8;
1533 /* DEC now has a specification (see Notes) but early board makers
1534 just put the address in the first EEPROM locations. */
1535 /* This does memcmp(ee_data, ee_data+16, 8) */
1536 for (i = 0; i < 8; i ++)
1537 if (ee_data[i] != ee_data[16+i])
1538 sa_offset = 20;
1539 if (chip_idx == CONEXANT) {
1540 /* Check that the tuple type and length is correct. */
1541 if (ee_data[0x198] == 0x04 && ee_data[0x199] == 6)
1542 sa_offset = 0x19A;
1543 } else if (ee_data[0] == 0xff && ee_data[1] == 0xff &&
1544 ee_data[2] == 0) {
1545 sa_offset = 2; /* Grrr, damn Matrox boards. */
1547 #ifdef CONFIG_MIPS_COBALT
1548 if ((pdev->bus->number == 0) &&
1549 ((PCI_SLOT(pdev->devfn) == 7) ||
1550 (PCI_SLOT(pdev->devfn) == 12))) {
1551 /* Cobalt MAC address in first EEPROM locations. */
1552 sa_offset = 0;
1553 /* Ensure our media table fixup get's applied */
1554 memcpy(ee_data + 16, ee_data, 8);
1556 #endif
1557 #ifdef CONFIG_GSC
1558 /* Check to see if we have a broken srom */
1559 if (ee_data[0] == 0x61 && ee_data[1] == 0x10) {
1560 /* pci_vendor_id and subsystem_id are swapped */
1561 ee_data[0] = ee_data[2];
1562 ee_data[1] = ee_data[3];
1563 ee_data[2] = 0x61;
1564 ee_data[3] = 0x10;
1566 /* HSC-PCI boards need to be byte-swaped and shifted
1567 * up 1 word. This shift needs to happen at the end
1568 * of the MAC first because of the 2 byte overlap.
1570 for (i = 4; i >= 0; i -= 2) {
1571 ee_data[17 + i + 3] = ee_data[17 + i];
1572 ee_data[16 + i + 5] = ee_data[16 + i];
1575 #endif
1577 for (i = 0; i < 6; i ++) {
1578 dev->dev_addr[i] = ee_data[i + sa_offset];
1579 sum += ee_data[i + sa_offset];
1582 /* Lite-On boards have the address byte-swapped. */
1583 if ((dev->dev_addr[0] == 0xA0 ||
1584 dev->dev_addr[0] == 0xC0 ||
1585 dev->dev_addr[0] == 0x02) &&
1586 dev->dev_addr[1] == 0x00)
1587 for (i = 0; i < 6; i+=2) {
1588 char tmp = dev->dev_addr[i];
1589 dev->dev_addr[i] = dev->dev_addr[i+1];
1590 dev->dev_addr[i+1] = tmp;
1592 /* On the Zynx 315 Etherarray and other multiport boards only the
1593 first Tulip has an EEPROM.
1594 On Sparc systems the mac address is held in the OBP property
1595 "local-mac-address".
1596 The addresses of the subsequent ports are derived from the first.
1597 Many PCI BIOSes also incorrectly report the IRQ line, so we correct
1598 that here as well. */
1599 if (sum == 0 || sum == 6*0xff) {
1600 #if defined(CONFIG_SPARC)
1601 struct device_node *dp = pci_device_to_OF_node(pdev);
1602 const unsigned char *addr;
1603 int len;
1604 #endif
1605 eeprom_missing = 1;
1606 for (i = 0; i < 5; i++)
1607 dev->dev_addr[i] = last_phys_addr[i];
1608 dev->dev_addr[i] = last_phys_addr[i] + 1;
1609 #if defined(CONFIG_SPARC)
1610 addr = of_get_property(dp, "local-mac-address", &len);
1611 if (addr && len == ETH_ALEN)
1612 memcpy(dev->dev_addr, addr, ETH_ALEN);
1613 #endif
1614 #if defined(__i386__) || defined(__x86_64__) /* Patch up x86 BIOS bug. */
1615 if (last_irq)
1616 irq = last_irq;
1617 #endif
1620 for (i = 0; i < 6; i++)
1621 last_phys_addr[i] = dev->dev_addr[i];
1622 #if defined(__i386__) || defined(__x86_64__) /* Patch up x86 BIOS bug. */
1623 last_irq = irq;
1624 #endif
1626 /* The lower four bits are the media type. */
1627 if (board_idx >= 0 && board_idx < MAX_UNITS) {
1628 if (options[board_idx] & MEDIA_MASK)
1629 tp->default_port = options[board_idx] & MEDIA_MASK;
1630 if ((options[board_idx] & FullDuplex) || full_duplex[board_idx] > 0)
1631 tp->full_duplex = 1;
1632 if (mtu[board_idx] > 0)
1633 dev->mtu = mtu[board_idx];
1635 if (dev->mem_start & MEDIA_MASK)
1636 tp->default_port = dev->mem_start & MEDIA_MASK;
1637 if (tp->default_port) {
1638 pr_info(DRV_NAME "%d: Transceiver selection forced to %s\n",
1639 board_idx, medianame[tp->default_port & MEDIA_MASK]);
1640 tp->medialock = 1;
1641 if (tulip_media_cap[tp->default_port] & MediaAlwaysFD)
1642 tp->full_duplex = 1;
1644 if (tp->full_duplex)
1645 tp->full_duplex_lock = 1;
1647 if (tulip_media_cap[tp->default_port] & MediaIsMII) {
1648 static const u16 media2advert[] = {
1649 0x20, 0x40, 0x03e0, 0x60, 0x80, 0x100, 0x200
1651 tp->mii_advertise = media2advert[tp->default_port - 9];
1652 tp->mii_advertise |= (tp->flags & HAS_8023X); /* Matching bits! */
1655 if (tp->flags & HAS_MEDIA_TABLE) {
1656 sprintf(dev->name, DRV_NAME "%d", board_idx); /* hack */
1657 tulip_parse_eeprom(dev);
1658 strcpy(dev->name, "eth%d"); /* un-hack */
1661 if ((tp->flags & ALWAYS_CHECK_MII) ||
1662 (tp->mtable && tp->mtable->has_mii) ||
1663 ( ! tp->mtable && (tp->flags & HAS_MII))) {
1664 if (tp->mtable && tp->mtable->has_mii) {
1665 for (i = 0; i < tp->mtable->leafcount; i++)
1666 if (tp->mtable->mleaf[i].media == 11) {
1667 tp->cur_index = i;
1668 tp->saved_if_port = dev->if_port;
1669 tulip_select_media(dev, 2);
1670 dev->if_port = tp->saved_if_port;
1671 break;
1675 /* Find the connected MII xcvrs.
1676 Doing this in open() would allow detecting external xcvrs
1677 later, but takes much time. */
1678 tulip_find_mii (dev, board_idx);
1681 /* The Tulip-specific entries in the device structure. */
1682 dev->netdev_ops = &tulip_netdev_ops;
1683 dev->watchdog_timeo = TX_TIMEOUT;
1684 #ifdef CONFIG_TULIP_NAPI
1685 netif_napi_add(dev, &tp->napi, tulip_poll, 16);
1686 #endif
1687 dev->ethtool_ops = &ops;
1689 if (register_netdev(dev))
1690 goto err_out_free_ring;
1692 pci_set_drvdata(pdev, dev);
1694 dev_info(&dev->dev,
1695 #ifdef CONFIG_TULIP_MMIO
1696 "%s rev %d at MMIO %#llx,%s %pM, IRQ %d\n",
1697 #else
1698 "%s rev %d at Port %#llx,%s %pM, IRQ %d\n",
1699 #endif
1700 chip_name, pdev->revision,
1701 (unsigned long long)pci_resource_start(pdev, TULIP_BAR),
1702 eeprom_missing ? " EEPROM not present," : "",
1703 dev->dev_addr, irq);
1705 if (tp->chip_id == PNIC2)
1706 tp->link_change = pnic2_lnk_change;
1707 else if (tp->flags & HAS_NWAY)
1708 tp->link_change = t21142_lnk_change;
1709 else if (tp->flags & HAS_PNICNWAY)
1710 tp->link_change = pnic_lnk_change;
1712 /* Reset the xcvr interface and turn on heartbeat. */
1713 switch (chip_idx) {
1714 case DC21140:
1715 case DM910X:
1716 default:
1717 if (tp->mtable)
1718 iowrite32(tp->mtable->csr12dir | 0x100, ioaddr + CSR12);
1719 break;
1720 case DC21142:
1721 if (tp->mii_cnt || tulip_media_cap[dev->if_port] & MediaIsMII) {
1722 iowrite32(csr6_mask_defstate, ioaddr + CSR6);
1723 iowrite32(0x0000, ioaddr + CSR13);
1724 iowrite32(0x0000, ioaddr + CSR14);
1725 iowrite32(csr6_mask_hdcap, ioaddr + CSR6);
1726 } else
1727 t21142_start_nway(dev);
1728 break;
1729 case PNIC2:
1730 /* just do a reset for sanity sake */
1731 iowrite32(0x0000, ioaddr + CSR13);
1732 iowrite32(0x0000, ioaddr + CSR14);
1733 break;
1734 case LC82C168:
1735 if ( ! tp->mii_cnt) {
1736 tp->nway = 1;
1737 tp->nwayset = 0;
1738 iowrite32(csr6_ttm | csr6_ca, ioaddr + CSR6);
1739 iowrite32(0x30, ioaddr + CSR12);
1740 iowrite32(0x0001F078, ioaddr + CSR6);
1741 iowrite32(0x0201F078, ioaddr + CSR6); /* Turn on autonegotiation. */
1743 break;
1744 case MX98713:
1745 case COMPEX9881:
1746 iowrite32(0x00000000, ioaddr + CSR6);
1747 iowrite32(0x000711C0, ioaddr + CSR14); /* Turn on NWay. */
1748 iowrite32(0x00000001, ioaddr + CSR13);
1749 break;
1750 case MX98715:
1751 case MX98725:
1752 iowrite32(0x01a80000, ioaddr + CSR6);
1753 iowrite32(0xFFFFFFFF, ioaddr + CSR14);
1754 iowrite32(0x00001000, ioaddr + CSR12);
1755 break;
1756 case COMET:
1757 /* No initialization necessary. */
1758 break;
1761 /* put the chip in snooze mode until opened */
1762 tulip_set_power_state (tp, 0, 1);
1764 return 0;
1766 err_out_free_ring:
1767 dma_free_coherent(&pdev->dev,
1768 sizeof(struct tulip_rx_desc) * RX_RING_SIZE +
1769 sizeof(struct tulip_tx_desc) * TX_RING_SIZE,
1770 tp->rx_ring, tp->rx_ring_dma);
1772 err_out_mtable:
1773 kfree (tp->mtable);
1774 pci_iounmap(pdev, ioaddr);
1776 err_out_free_res:
1777 pci_release_regions (pdev);
1779 err_out_free_netdev:
1780 free_netdev (dev);
1781 return -ENODEV;
1785 /* set the registers according to the given wolopts */
1786 static void tulip_set_wolopts (struct pci_dev *pdev, u32 wolopts)
1788 struct net_device *dev = pci_get_drvdata(pdev);
1789 struct tulip_private *tp = netdev_priv(dev);
1790 void __iomem *ioaddr = tp->base_addr;
1792 if (tp->flags & COMET_PM) {
1793 unsigned int tmp;
1795 tmp = ioread32(ioaddr + CSR18);
1796 tmp &= ~(comet_csr18_pmes_sticky | comet_csr18_apm_mode | comet_csr18_d3a);
1797 tmp |= comet_csr18_pm_mode;
1798 iowrite32(tmp, ioaddr + CSR18);
1800 /* Set the Wake-up Control/Status Register to the given WOL options*/
1801 tmp = ioread32(ioaddr + CSR13);
1802 tmp &= ~(comet_csr13_linkoffe | comet_csr13_linkone | comet_csr13_wfre | comet_csr13_lsce | comet_csr13_mpre);
1803 if (wolopts & WAKE_MAGIC)
1804 tmp |= comet_csr13_mpre;
1805 if (wolopts & WAKE_PHY)
1806 tmp |= comet_csr13_linkoffe | comet_csr13_linkone | comet_csr13_lsce;
1807 /* Clear the event flags */
1808 tmp |= comet_csr13_wfr | comet_csr13_mpr | comet_csr13_lsc;
1809 iowrite32(tmp, ioaddr + CSR13);
1813 static int __maybe_unused tulip_suspend(struct device *dev_d)
1815 struct net_device *dev = dev_get_drvdata(dev_d);
1816 struct tulip_private *tp = netdev_priv(dev);
1818 if (!dev)
1819 return -EINVAL;
1821 if (!netif_running(dev))
1822 goto save_state;
1824 tulip_down(dev);
1826 netif_device_detach(dev);
1827 /* FIXME: it needlessly adds an error path. */
1828 free_irq(tp->pdev->irq, dev);
1830 save_state:
1831 tulip_set_wolopts(to_pci_dev(dev_d), tp->wolinfo.wolopts);
1832 device_set_wakeup_enable(dev_d, !!tp->wolinfo.wolopts);
1834 return 0;
1837 static int __maybe_unused tulip_resume(struct device *dev_d)
1839 struct pci_dev *pdev = to_pci_dev(dev_d);
1840 struct net_device *dev = dev_get_drvdata(dev_d);
1841 struct tulip_private *tp = netdev_priv(dev);
1842 void __iomem *ioaddr = tp->base_addr;
1843 unsigned int tmp;
1844 int retval = 0;
1846 if (!dev)
1847 return -EINVAL;
1849 if (!netif_running(dev))
1850 return 0;
1852 retval = request_irq(pdev->irq, tulip_interrupt, IRQF_SHARED,
1853 dev->name, dev);
1854 if (retval) {
1855 pr_err("request_irq failed in resume\n");
1856 return retval;
1859 if (tp->flags & COMET_PM) {
1860 device_set_wakeup_enable(dev_d, 0);
1862 /* Clear the PMES flag */
1863 tmp = ioread32(ioaddr + CSR20);
1864 tmp |= comet_csr20_pmes;
1865 iowrite32(tmp, ioaddr + CSR20);
1867 /* Disable all wake-up events */
1868 tulip_set_wolopts(pdev, 0);
1870 netif_device_attach(dev);
1872 if (netif_running(dev))
1873 tulip_up(dev);
1875 return 0;
1878 static void tulip_remove_one(struct pci_dev *pdev)
1880 struct net_device *dev = pci_get_drvdata (pdev);
1881 struct tulip_private *tp;
1883 if (!dev)
1884 return;
1886 tp = netdev_priv(dev);
1887 unregister_netdev(dev);
1888 dma_free_coherent(&pdev->dev,
1889 sizeof(struct tulip_rx_desc) * RX_RING_SIZE +
1890 sizeof(struct tulip_tx_desc) * TX_RING_SIZE,
1891 tp->rx_ring, tp->rx_ring_dma);
1892 kfree (tp->mtable);
1893 pci_iounmap(pdev, tp->base_addr);
1894 free_netdev (dev);
1895 pci_release_regions (pdev);
1896 pci_disable_device(pdev);
1898 /* pci_power_off (pdev, -1); */
1901 #ifdef CONFIG_NET_POLL_CONTROLLER
1903 * Polling 'interrupt' - used by things like netconsole to send skbs
1904 * without having to re-enable interrupts. It's not called while
1905 * the interrupt routine is executing.
1908 static void poll_tulip (struct net_device *dev)
1910 struct tulip_private *tp = netdev_priv(dev);
1911 const int irq = tp->pdev->irq;
1913 /* disable_irq here is not very nice, but with the lockless
1914 interrupt handler we have no other choice. */
1915 disable_irq(irq);
1916 tulip_interrupt (irq, dev);
1917 enable_irq(irq);
1919 #endif
1921 static SIMPLE_DEV_PM_OPS(tulip_pm_ops, tulip_suspend, tulip_resume);
1923 static struct pci_driver tulip_driver = {
1924 .name = DRV_NAME,
1925 .id_table = tulip_pci_tbl,
1926 .probe = tulip_init_one,
1927 .remove = tulip_remove_one,
1928 .driver.pm = &tulip_pm_ops,
1932 static int __init tulip_init (void)
1934 if (!csr0) {
1935 pr_warn("tulip: unknown CPU architecture, using default csr0\n");
1936 /* default to 8 longword cache line alignment */
1937 csr0 = 0x00A00000 | 0x4800;
1940 /* copy module parms into globals */
1941 tulip_rx_copybreak = rx_copybreak;
1942 tulip_max_interrupt_work = max_interrupt_work;
1944 /* probe for and init boards */
1945 return pci_register_driver(&tulip_driver);
1949 static void __exit tulip_cleanup (void)
1951 pci_unregister_driver (&tulip_driver);
1955 module_init(tulip_init);
1956 module_exit(tulip_cleanup);