WIP FPC-III support
[linux/fpc-iii.git] / drivers / phy / mediatek / phy-mtk-tphy.c
blobcdbcc49f71152cf479ab1a35eabeb8b663469f10
1 // SPDX-License-Identifier: GPL-2.0
2 /*
3 * Copyright (c) 2015 MediaTek Inc.
4 * Author: Chunfeng Yun <chunfeng.yun@mediatek.com>
6 */
8 #include <dt-bindings/phy/phy.h>
9 #include <linux/clk.h>
10 #include <linux/delay.h>
11 #include <linux/io.h>
12 #include <linux/iopoll.h>
13 #include <linux/module.h>
14 #include <linux/of_address.h>
15 #include <linux/of_device.h>
16 #include <linux/phy/phy.h>
17 #include <linux/platform_device.h>
19 /* version V1 sub-banks offset base address */
20 /* banks shared by multiple phys */
21 #define SSUSB_SIFSLV_V1_SPLLC 0x000 /* shared by u3 phys */
22 #define SSUSB_SIFSLV_V1_U2FREQ 0x100 /* shared by u2 phys */
23 #define SSUSB_SIFSLV_V1_CHIP 0x300 /* shared by u3 phys */
24 /* u2 phy bank */
25 #define SSUSB_SIFSLV_V1_U2PHY_COM 0x000
26 /* u3/pcie/sata phy banks */
27 #define SSUSB_SIFSLV_V1_U3PHYD 0x000
28 #define SSUSB_SIFSLV_V1_U3PHYA 0x200
30 /* version V2 sub-banks offset base address */
31 /* u2 phy banks */
32 #define SSUSB_SIFSLV_V2_MISC 0x000
33 #define SSUSB_SIFSLV_V2_U2FREQ 0x100
34 #define SSUSB_SIFSLV_V2_U2PHY_COM 0x300
35 /* u3/pcie/sata phy banks */
36 #define SSUSB_SIFSLV_V2_SPLLC 0x000
37 #define SSUSB_SIFSLV_V2_CHIP 0x100
38 #define SSUSB_SIFSLV_V2_U3PHYD 0x200
39 #define SSUSB_SIFSLV_V2_U3PHYA 0x400
41 #define U3P_USBPHYACR0 0x000
42 #define PA0_RG_U2PLL_FORCE_ON BIT(15)
43 #define PA0_RG_USB20_INTR_EN BIT(5)
45 #define U3P_USBPHYACR1 0x004
46 #define PA1_RG_INTR_CAL GENMASK(23, 19)
47 #define PA1_RG_INTR_CAL_VAL(x) ((0x1f & (x)) << 19)
48 #define PA1_RG_VRT_SEL GENMASK(14, 12)
49 #define PA1_RG_VRT_SEL_VAL(x) ((0x7 & (x)) << 12)
50 #define PA1_RG_TERM_SEL GENMASK(10, 8)
51 #define PA1_RG_TERM_SEL_VAL(x) ((0x7 & (x)) << 8)
53 #define U3P_USBPHYACR2 0x008
54 #define PA2_RG_SIF_U2PLL_FORCE_EN BIT(18)
56 #define U3P_USBPHYACR5 0x014
57 #define PA5_RG_U2_HSTX_SRCAL_EN BIT(15)
58 #define PA5_RG_U2_HSTX_SRCTRL GENMASK(14, 12)
59 #define PA5_RG_U2_HSTX_SRCTRL_VAL(x) ((0x7 & (x)) << 12)
60 #define PA5_RG_U2_HS_100U_U3_EN BIT(11)
62 #define U3P_USBPHYACR6 0x018
63 #define PA6_RG_U2_BC11_SW_EN BIT(23)
64 #define PA6_RG_U2_OTG_VBUSCMP_EN BIT(20)
65 #define PA6_RG_U2_DISCTH GENMASK(7, 4)
66 #define PA6_RG_U2_DISCTH_VAL(x) ((0xf & (x)) << 4)
67 #define PA6_RG_U2_SQTH GENMASK(3, 0)
68 #define PA6_RG_U2_SQTH_VAL(x) (0xf & (x))
70 #define U3P_U2PHYACR4 0x020
71 #define P2C_RG_USB20_GPIO_CTL BIT(9)
72 #define P2C_USB20_GPIO_MODE BIT(8)
73 #define P2C_U2_GPIO_CTR_MSK (P2C_RG_USB20_GPIO_CTL | P2C_USB20_GPIO_MODE)
75 #define U3D_U2PHYDCR0 0x060
76 #define P2C_RG_SIF_U2PLL_FORCE_ON BIT(24)
78 #define U3P_U2PHYDTM0 0x068
79 #define P2C_FORCE_UART_EN BIT(26)
80 #define P2C_FORCE_DATAIN BIT(23)
81 #define P2C_FORCE_DM_PULLDOWN BIT(21)
82 #define P2C_FORCE_DP_PULLDOWN BIT(20)
83 #define P2C_FORCE_XCVRSEL BIT(19)
84 #define P2C_FORCE_SUSPENDM BIT(18)
85 #define P2C_FORCE_TERMSEL BIT(17)
86 #define P2C_RG_DATAIN GENMASK(13, 10)
87 #define P2C_RG_DATAIN_VAL(x) ((0xf & (x)) << 10)
88 #define P2C_RG_DMPULLDOWN BIT(7)
89 #define P2C_RG_DPPULLDOWN BIT(6)
90 #define P2C_RG_XCVRSEL GENMASK(5, 4)
91 #define P2C_RG_XCVRSEL_VAL(x) ((0x3 & (x)) << 4)
92 #define P2C_RG_SUSPENDM BIT(3)
93 #define P2C_RG_TERMSEL BIT(2)
94 #define P2C_DTM0_PART_MASK \
95 (P2C_FORCE_DATAIN | P2C_FORCE_DM_PULLDOWN | \
96 P2C_FORCE_DP_PULLDOWN | P2C_FORCE_XCVRSEL | \
97 P2C_FORCE_TERMSEL | P2C_RG_DMPULLDOWN | \
98 P2C_RG_DPPULLDOWN | P2C_RG_TERMSEL)
100 #define U3P_U2PHYDTM1 0x06C
101 #define P2C_RG_UART_EN BIT(16)
102 #define P2C_FORCE_IDDIG BIT(9)
103 #define P2C_RG_VBUSVALID BIT(5)
104 #define P2C_RG_SESSEND BIT(4)
105 #define P2C_RG_AVALID BIT(2)
106 #define P2C_RG_IDDIG BIT(1)
108 #define U3P_U2PHYBC12C 0x080
109 #define P2C_RG_CHGDT_EN BIT(0)
111 #define U3P_U3_CHIP_GPIO_CTLD 0x0c
112 #define P3C_REG_IP_SW_RST BIT(31)
113 #define P3C_MCU_BUS_CK_GATE_EN BIT(30)
114 #define P3C_FORCE_IP_SW_RST BIT(29)
116 #define U3P_U3_CHIP_GPIO_CTLE 0x10
117 #define P3C_RG_SWRST_U3_PHYD BIT(25)
118 #define P3C_RG_SWRST_U3_PHYD_FORCE_EN BIT(24)
120 #define U3P_U3_PHYA_REG0 0x000
121 #define P3A_RG_CLKDRV_OFF GENMASK(3, 2)
122 #define P3A_RG_CLKDRV_OFF_VAL(x) ((0x3 & (x)) << 2)
124 #define U3P_U3_PHYA_REG1 0x004
125 #define P3A_RG_CLKDRV_AMP GENMASK(31, 29)
126 #define P3A_RG_CLKDRV_AMP_VAL(x) ((0x7 & (x)) << 29)
128 #define U3P_U3_PHYA_REG6 0x018
129 #define P3A_RG_TX_EIDLE_CM GENMASK(31, 28)
130 #define P3A_RG_TX_EIDLE_CM_VAL(x) ((0xf & (x)) << 28)
132 #define U3P_U3_PHYA_REG9 0x024
133 #define P3A_RG_RX_DAC_MUX GENMASK(5, 1)
134 #define P3A_RG_RX_DAC_MUX_VAL(x) ((0x1f & (x)) << 1)
136 #define U3P_U3_PHYA_DA_REG0 0x100
137 #define P3A_RG_XTAL_EXT_PE2H GENMASK(17, 16)
138 #define P3A_RG_XTAL_EXT_PE2H_VAL(x) ((0x3 & (x)) << 16)
139 #define P3A_RG_XTAL_EXT_PE1H GENMASK(13, 12)
140 #define P3A_RG_XTAL_EXT_PE1H_VAL(x) ((0x3 & (x)) << 12)
141 #define P3A_RG_XTAL_EXT_EN_U3 GENMASK(11, 10)
142 #define P3A_RG_XTAL_EXT_EN_U3_VAL(x) ((0x3 & (x)) << 10)
144 #define U3P_U3_PHYA_DA_REG4 0x108
145 #define P3A_RG_PLL_DIVEN_PE2H GENMASK(21, 19)
146 #define P3A_RG_PLL_BC_PE2H GENMASK(7, 6)
147 #define P3A_RG_PLL_BC_PE2H_VAL(x) ((0x3 & (x)) << 6)
149 #define U3P_U3_PHYA_DA_REG5 0x10c
150 #define P3A_RG_PLL_BR_PE2H GENMASK(29, 28)
151 #define P3A_RG_PLL_BR_PE2H_VAL(x) ((0x3 & (x)) << 28)
152 #define P3A_RG_PLL_IC_PE2H GENMASK(15, 12)
153 #define P3A_RG_PLL_IC_PE2H_VAL(x) ((0xf & (x)) << 12)
155 #define U3P_U3_PHYA_DA_REG6 0x110
156 #define P3A_RG_PLL_IR_PE2H GENMASK(19, 16)
157 #define P3A_RG_PLL_IR_PE2H_VAL(x) ((0xf & (x)) << 16)
159 #define U3P_U3_PHYA_DA_REG7 0x114
160 #define P3A_RG_PLL_BP_PE2H GENMASK(19, 16)
161 #define P3A_RG_PLL_BP_PE2H_VAL(x) ((0xf & (x)) << 16)
163 #define U3P_U3_PHYA_DA_REG20 0x13c
164 #define P3A_RG_PLL_DELTA1_PE2H GENMASK(31, 16)
165 #define P3A_RG_PLL_DELTA1_PE2H_VAL(x) ((0xffff & (x)) << 16)
167 #define U3P_U3_PHYA_DA_REG25 0x148
168 #define P3A_RG_PLL_DELTA_PE2H GENMASK(15, 0)
169 #define P3A_RG_PLL_DELTA_PE2H_VAL(x) (0xffff & (x))
171 #define U3P_U3_PHYD_LFPS1 0x00c
172 #define P3D_RG_FWAKE_TH GENMASK(21, 16)
173 #define P3D_RG_FWAKE_TH_VAL(x) ((0x3f & (x)) << 16)
175 #define U3P_U3_PHYD_CDR1 0x05c
176 #define P3D_RG_CDR_BIR_LTD1 GENMASK(28, 24)
177 #define P3D_RG_CDR_BIR_LTD1_VAL(x) ((0x1f & (x)) << 24)
178 #define P3D_RG_CDR_BIR_LTD0 GENMASK(12, 8)
179 #define P3D_RG_CDR_BIR_LTD0_VAL(x) ((0x1f & (x)) << 8)
181 #define U3P_U3_PHYD_RXDET1 0x128
182 #define P3D_RG_RXDET_STB2_SET GENMASK(17, 9)
183 #define P3D_RG_RXDET_STB2_SET_VAL(x) ((0x1ff & (x)) << 9)
185 #define U3P_U3_PHYD_RXDET2 0x12c
186 #define P3D_RG_RXDET_STB2_SET_P3 GENMASK(8, 0)
187 #define P3D_RG_RXDET_STB2_SET_P3_VAL(x) (0x1ff & (x))
189 #define U3P_SPLLC_XTALCTL3 0x018
190 #define XC3_RG_U3_XTAL_RX_PWD BIT(9)
191 #define XC3_RG_U3_FRC_XTAL_RX_PWD BIT(8)
193 #define U3P_U2FREQ_FMCR0 0x00
194 #define P2F_RG_MONCLK_SEL GENMASK(27, 26)
195 #define P2F_RG_MONCLK_SEL_VAL(x) ((0x3 & (x)) << 26)
196 #define P2F_RG_FREQDET_EN BIT(24)
197 #define P2F_RG_CYCLECNT GENMASK(23, 0)
198 #define P2F_RG_CYCLECNT_VAL(x) ((P2F_RG_CYCLECNT) & (x))
200 #define U3P_U2FREQ_VALUE 0x0c
202 #define U3P_U2FREQ_FMMONR1 0x10
203 #define P2F_USB_FM_VALID BIT(0)
204 #define P2F_RG_FRCK_EN BIT(8)
206 #define U3P_REF_CLK 26 /* MHZ */
207 #define U3P_SLEW_RATE_COEF 28
208 #define U3P_SR_COEF_DIVISOR 1000
209 #define U3P_FM_DET_CYCLE_CNT 1024
211 /* SATA register setting */
212 #define PHYD_CTRL_SIGNAL_MODE4 0x1c
213 /* CDR Charge Pump P-path current adjustment */
214 #define RG_CDR_BICLTD1_GEN1_MSK GENMASK(23, 20)
215 #define RG_CDR_BICLTD1_GEN1_VAL(x) ((0xf & (x)) << 20)
216 #define RG_CDR_BICLTD0_GEN1_MSK GENMASK(11, 8)
217 #define RG_CDR_BICLTD0_GEN1_VAL(x) ((0xf & (x)) << 8)
219 #define PHYD_DESIGN_OPTION2 0x24
220 /* Symbol lock count selection */
221 #define RG_LOCK_CNT_SEL_MSK GENMASK(5, 4)
222 #define RG_LOCK_CNT_SEL_VAL(x) ((0x3 & (x)) << 4)
224 #define PHYD_DESIGN_OPTION9 0x40
225 /* COMWAK GAP width window */
226 #define RG_TG_MAX_MSK GENMASK(20, 16)
227 #define RG_TG_MAX_VAL(x) ((0x1f & (x)) << 16)
228 /* COMINIT GAP width window */
229 #define RG_T2_MAX_MSK GENMASK(13, 8)
230 #define RG_T2_MAX_VAL(x) ((0x3f & (x)) << 8)
231 /* COMWAK GAP width window */
232 #define RG_TG_MIN_MSK GENMASK(7, 5)
233 #define RG_TG_MIN_VAL(x) ((0x7 & (x)) << 5)
234 /* COMINIT GAP width window */
235 #define RG_T2_MIN_MSK GENMASK(4, 0)
236 #define RG_T2_MIN_VAL(x) (0x1f & (x))
238 #define ANA_RG_CTRL_SIGNAL1 0x4c
239 /* TX driver tail current control for 0dB de-empahsis mdoe for Gen1 speed */
240 #define RG_IDRV_0DB_GEN1_MSK GENMASK(13, 8)
241 #define RG_IDRV_0DB_GEN1_VAL(x) ((0x3f & (x)) << 8)
243 #define ANA_RG_CTRL_SIGNAL4 0x58
244 #define RG_CDR_BICLTR_GEN1_MSK GENMASK(23, 20)
245 #define RG_CDR_BICLTR_GEN1_VAL(x) ((0xf & (x)) << 20)
246 /* Loop filter R1 resistance adjustment for Gen1 speed */
247 #define RG_CDR_BR_GEN2_MSK GENMASK(10, 8)
248 #define RG_CDR_BR_GEN2_VAL(x) ((0x7 & (x)) << 8)
250 #define ANA_RG_CTRL_SIGNAL6 0x60
251 /* I-path capacitance adjustment for Gen1 */
252 #define RG_CDR_BC_GEN1_MSK GENMASK(28, 24)
253 #define RG_CDR_BC_GEN1_VAL(x) ((0x1f & (x)) << 24)
254 #define RG_CDR_BIRLTR_GEN1_MSK GENMASK(4, 0)
255 #define RG_CDR_BIRLTR_GEN1_VAL(x) (0x1f & (x))
257 #define ANA_EQ_EYE_CTRL_SIGNAL1 0x6c
258 /* RX Gen1 LEQ tuning step */
259 #define RG_EQ_DLEQ_LFI_GEN1_MSK GENMASK(11, 8)
260 #define RG_EQ_DLEQ_LFI_GEN1_VAL(x) ((0xf & (x)) << 8)
262 #define ANA_EQ_EYE_CTRL_SIGNAL4 0xd8
263 #define RG_CDR_BIRLTD0_GEN1_MSK GENMASK(20, 16)
264 #define RG_CDR_BIRLTD0_GEN1_VAL(x) ((0x1f & (x)) << 16)
266 #define ANA_EQ_EYE_CTRL_SIGNAL5 0xdc
267 #define RG_CDR_BIRLTD0_GEN3_MSK GENMASK(4, 0)
268 #define RG_CDR_BIRLTD0_GEN3_VAL(x) (0x1f & (x))
270 enum mtk_phy_version {
271 MTK_PHY_V1 = 1,
272 MTK_PHY_V2,
275 struct mtk_phy_pdata {
276 /* avoid RX sensitivity level degradation only for mt8173 */
277 bool avoid_rx_sen_degradation;
278 enum mtk_phy_version version;
281 struct u2phy_banks {
282 void __iomem *misc;
283 void __iomem *fmreg;
284 void __iomem *com;
287 struct u3phy_banks {
288 void __iomem *spllc;
289 void __iomem *chip;
290 void __iomem *phyd; /* include u3phyd_bank2 */
291 void __iomem *phya; /* include u3phya_da */
294 struct mtk_phy_instance {
295 struct phy *phy;
296 void __iomem *port_base;
297 union {
298 struct u2phy_banks u2_banks;
299 struct u3phy_banks u3_banks;
301 struct clk *ref_clk; /* reference clock of (digital) phy */
302 struct clk *da_ref_clk; /* reference clock of analog phy */
303 u32 index;
304 u8 type;
305 int eye_src;
306 int eye_vrt;
307 int eye_term;
308 int intr;
309 int discth;
310 bool bc12_en;
313 struct mtk_tphy {
314 struct device *dev;
315 void __iomem *sif_base; /* only shared sif */
316 const struct mtk_phy_pdata *pdata;
317 struct mtk_phy_instance **phys;
318 int nphys;
319 int src_ref_clk; /* MHZ, reference clock for slew rate calibrate */
320 int src_coef; /* coefficient for slew rate calibrate */
323 static void hs_slew_rate_calibrate(struct mtk_tphy *tphy,
324 struct mtk_phy_instance *instance)
326 struct u2phy_banks *u2_banks = &instance->u2_banks;
327 void __iomem *fmreg = u2_banks->fmreg;
328 void __iomem *com = u2_banks->com;
329 int calibration_val;
330 int fm_out;
331 u32 tmp;
333 /* use force value */
334 if (instance->eye_src)
335 return;
337 /* enable USB ring oscillator */
338 tmp = readl(com + U3P_USBPHYACR5);
339 tmp |= PA5_RG_U2_HSTX_SRCAL_EN;
340 writel(tmp, com + U3P_USBPHYACR5);
341 udelay(1);
343 /*enable free run clock */
344 tmp = readl(fmreg + U3P_U2FREQ_FMMONR1);
345 tmp |= P2F_RG_FRCK_EN;
346 writel(tmp, fmreg + U3P_U2FREQ_FMMONR1);
348 /* set cycle count as 1024, and select u2 channel */
349 tmp = readl(fmreg + U3P_U2FREQ_FMCR0);
350 tmp &= ~(P2F_RG_CYCLECNT | P2F_RG_MONCLK_SEL);
351 tmp |= P2F_RG_CYCLECNT_VAL(U3P_FM_DET_CYCLE_CNT);
352 if (tphy->pdata->version == MTK_PHY_V1)
353 tmp |= P2F_RG_MONCLK_SEL_VAL(instance->index >> 1);
355 writel(tmp, fmreg + U3P_U2FREQ_FMCR0);
357 /* enable frequency meter */
358 tmp = readl(fmreg + U3P_U2FREQ_FMCR0);
359 tmp |= P2F_RG_FREQDET_EN;
360 writel(tmp, fmreg + U3P_U2FREQ_FMCR0);
362 /* ignore return value */
363 readl_poll_timeout(fmreg + U3P_U2FREQ_FMMONR1, tmp,
364 (tmp & P2F_USB_FM_VALID), 10, 200);
366 fm_out = readl(fmreg + U3P_U2FREQ_VALUE);
368 /* disable frequency meter */
369 tmp = readl(fmreg + U3P_U2FREQ_FMCR0);
370 tmp &= ~P2F_RG_FREQDET_EN;
371 writel(tmp, fmreg + U3P_U2FREQ_FMCR0);
373 /*disable free run clock */
374 tmp = readl(fmreg + U3P_U2FREQ_FMMONR1);
375 tmp &= ~P2F_RG_FRCK_EN;
376 writel(tmp, fmreg + U3P_U2FREQ_FMMONR1);
378 if (fm_out) {
379 /* ( 1024 / FM_OUT ) x reference clock frequency x coef */
380 tmp = tphy->src_ref_clk * tphy->src_coef;
381 tmp = (tmp * U3P_FM_DET_CYCLE_CNT) / fm_out;
382 calibration_val = DIV_ROUND_CLOSEST(tmp, U3P_SR_COEF_DIVISOR);
383 } else {
384 /* if FM detection fail, set default value */
385 calibration_val = 4;
387 dev_dbg(tphy->dev, "phy:%d, fm_out:%d, calib:%d (clk:%d, coef:%d)\n",
388 instance->index, fm_out, calibration_val,
389 tphy->src_ref_clk, tphy->src_coef);
391 /* set HS slew rate */
392 tmp = readl(com + U3P_USBPHYACR5);
393 tmp &= ~PA5_RG_U2_HSTX_SRCTRL;
394 tmp |= PA5_RG_U2_HSTX_SRCTRL_VAL(calibration_val);
395 writel(tmp, com + U3P_USBPHYACR5);
397 /* disable USB ring oscillator */
398 tmp = readl(com + U3P_USBPHYACR5);
399 tmp &= ~PA5_RG_U2_HSTX_SRCAL_EN;
400 writel(tmp, com + U3P_USBPHYACR5);
403 static void u3_phy_instance_init(struct mtk_tphy *tphy,
404 struct mtk_phy_instance *instance)
406 struct u3phy_banks *u3_banks = &instance->u3_banks;
407 u32 tmp;
409 /* gating PCIe Analog XTAL clock */
410 tmp = readl(u3_banks->spllc + U3P_SPLLC_XTALCTL3);
411 tmp |= XC3_RG_U3_XTAL_RX_PWD | XC3_RG_U3_FRC_XTAL_RX_PWD;
412 writel(tmp, u3_banks->spllc + U3P_SPLLC_XTALCTL3);
414 /* gating XSQ */
415 tmp = readl(u3_banks->phya + U3P_U3_PHYA_DA_REG0);
416 tmp &= ~P3A_RG_XTAL_EXT_EN_U3;
417 tmp |= P3A_RG_XTAL_EXT_EN_U3_VAL(2);
418 writel(tmp, u3_banks->phya + U3P_U3_PHYA_DA_REG0);
420 tmp = readl(u3_banks->phya + U3P_U3_PHYA_REG9);
421 tmp &= ~P3A_RG_RX_DAC_MUX;
422 tmp |= P3A_RG_RX_DAC_MUX_VAL(4);
423 writel(tmp, u3_banks->phya + U3P_U3_PHYA_REG9);
425 tmp = readl(u3_banks->phya + U3P_U3_PHYA_REG6);
426 tmp &= ~P3A_RG_TX_EIDLE_CM;
427 tmp |= P3A_RG_TX_EIDLE_CM_VAL(0xe);
428 writel(tmp, u3_banks->phya + U3P_U3_PHYA_REG6);
430 tmp = readl(u3_banks->phyd + U3P_U3_PHYD_CDR1);
431 tmp &= ~(P3D_RG_CDR_BIR_LTD0 | P3D_RG_CDR_BIR_LTD1);
432 tmp |= P3D_RG_CDR_BIR_LTD0_VAL(0xc) | P3D_RG_CDR_BIR_LTD1_VAL(0x3);
433 writel(tmp, u3_banks->phyd + U3P_U3_PHYD_CDR1);
435 tmp = readl(u3_banks->phyd + U3P_U3_PHYD_LFPS1);
436 tmp &= ~P3D_RG_FWAKE_TH;
437 tmp |= P3D_RG_FWAKE_TH_VAL(0x34);
438 writel(tmp, u3_banks->phyd + U3P_U3_PHYD_LFPS1);
440 tmp = readl(u3_banks->phyd + U3P_U3_PHYD_RXDET1);
441 tmp &= ~P3D_RG_RXDET_STB2_SET;
442 tmp |= P3D_RG_RXDET_STB2_SET_VAL(0x10);
443 writel(tmp, u3_banks->phyd + U3P_U3_PHYD_RXDET1);
445 tmp = readl(u3_banks->phyd + U3P_U3_PHYD_RXDET2);
446 tmp &= ~P3D_RG_RXDET_STB2_SET_P3;
447 tmp |= P3D_RG_RXDET_STB2_SET_P3_VAL(0x10);
448 writel(tmp, u3_banks->phyd + U3P_U3_PHYD_RXDET2);
450 dev_dbg(tphy->dev, "%s(%d)\n", __func__, instance->index);
453 static void u2_phy_instance_init(struct mtk_tphy *tphy,
454 struct mtk_phy_instance *instance)
456 struct u2phy_banks *u2_banks = &instance->u2_banks;
457 void __iomem *com = u2_banks->com;
458 u32 index = instance->index;
459 u32 tmp;
461 /* switch to USB function, and enable usb pll */
462 tmp = readl(com + U3P_U2PHYDTM0);
463 tmp &= ~(P2C_FORCE_UART_EN | P2C_FORCE_SUSPENDM);
464 tmp |= P2C_RG_XCVRSEL_VAL(1) | P2C_RG_DATAIN_VAL(0);
465 writel(tmp, com + U3P_U2PHYDTM0);
467 tmp = readl(com + U3P_U2PHYDTM1);
468 tmp &= ~P2C_RG_UART_EN;
469 writel(tmp, com + U3P_U2PHYDTM1);
471 tmp = readl(com + U3P_USBPHYACR0);
472 tmp |= PA0_RG_USB20_INTR_EN;
473 writel(tmp, com + U3P_USBPHYACR0);
475 /* disable switch 100uA current to SSUSB */
476 tmp = readl(com + U3P_USBPHYACR5);
477 tmp &= ~PA5_RG_U2_HS_100U_U3_EN;
478 writel(tmp, com + U3P_USBPHYACR5);
480 if (!index) {
481 tmp = readl(com + U3P_U2PHYACR4);
482 tmp &= ~P2C_U2_GPIO_CTR_MSK;
483 writel(tmp, com + U3P_U2PHYACR4);
486 if (tphy->pdata->avoid_rx_sen_degradation) {
487 if (!index) {
488 tmp = readl(com + U3P_USBPHYACR2);
489 tmp |= PA2_RG_SIF_U2PLL_FORCE_EN;
490 writel(tmp, com + U3P_USBPHYACR2);
492 tmp = readl(com + U3D_U2PHYDCR0);
493 tmp &= ~P2C_RG_SIF_U2PLL_FORCE_ON;
494 writel(tmp, com + U3D_U2PHYDCR0);
495 } else {
496 tmp = readl(com + U3D_U2PHYDCR0);
497 tmp |= P2C_RG_SIF_U2PLL_FORCE_ON;
498 writel(tmp, com + U3D_U2PHYDCR0);
500 tmp = readl(com + U3P_U2PHYDTM0);
501 tmp |= P2C_RG_SUSPENDM | P2C_FORCE_SUSPENDM;
502 writel(tmp, com + U3P_U2PHYDTM0);
506 tmp = readl(com + U3P_USBPHYACR6);
507 tmp &= ~PA6_RG_U2_BC11_SW_EN; /* DP/DM BC1.1 path Disable */
508 tmp &= ~PA6_RG_U2_SQTH;
509 tmp |= PA6_RG_U2_SQTH_VAL(2);
510 writel(tmp, com + U3P_USBPHYACR6);
512 dev_dbg(tphy->dev, "%s(%d)\n", __func__, index);
515 static void u2_phy_instance_power_on(struct mtk_tphy *tphy,
516 struct mtk_phy_instance *instance)
518 struct u2phy_banks *u2_banks = &instance->u2_banks;
519 void __iomem *com = u2_banks->com;
520 u32 index = instance->index;
521 u32 tmp;
523 tmp = readl(com + U3P_U2PHYDTM0);
524 tmp &= ~(P2C_RG_XCVRSEL | P2C_RG_DATAIN | P2C_DTM0_PART_MASK);
525 writel(tmp, com + U3P_U2PHYDTM0);
527 /* OTG Enable */
528 tmp = readl(com + U3P_USBPHYACR6);
529 tmp |= PA6_RG_U2_OTG_VBUSCMP_EN;
530 writel(tmp, com + U3P_USBPHYACR6);
532 tmp = readl(com + U3P_U2PHYDTM1);
533 tmp |= P2C_RG_VBUSVALID | P2C_RG_AVALID;
534 tmp &= ~P2C_RG_SESSEND;
535 writel(tmp, com + U3P_U2PHYDTM1);
537 if (tphy->pdata->avoid_rx_sen_degradation && index) {
538 tmp = readl(com + U3D_U2PHYDCR0);
539 tmp |= P2C_RG_SIF_U2PLL_FORCE_ON;
540 writel(tmp, com + U3D_U2PHYDCR0);
542 tmp = readl(com + U3P_U2PHYDTM0);
543 tmp |= P2C_RG_SUSPENDM | P2C_FORCE_SUSPENDM;
544 writel(tmp, com + U3P_U2PHYDTM0);
546 dev_dbg(tphy->dev, "%s(%d)\n", __func__, index);
549 static void u2_phy_instance_power_off(struct mtk_tphy *tphy,
550 struct mtk_phy_instance *instance)
552 struct u2phy_banks *u2_banks = &instance->u2_banks;
553 void __iomem *com = u2_banks->com;
554 u32 index = instance->index;
555 u32 tmp;
557 tmp = readl(com + U3P_U2PHYDTM0);
558 tmp &= ~(P2C_RG_XCVRSEL | P2C_RG_DATAIN);
559 writel(tmp, com + U3P_U2PHYDTM0);
561 /* OTG Disable */
562 tmp = readl(com + U3P_USBPHYACR6);
563 tmp &= ~PA6_RG_U2_OTG_VBUSCMP_EN;
564 writel(tmp, com + U3P_USBPHYACR6);
566 tmp = readl(com + U3P_U2PHYDTM1);
567 tmp &= ~(P2C_RG_VBUSVALID | P2C_RG_AVALID);
568 tmp |= P2C_RG_SESSEND;
569 writel(tmp, com + U3P_U2PHYDTM1);
571 if (tphy->pdata->avoid_rx_sen_degradation && index) {
572 tmp = readl(com + U3P_U2PHYDTM0);
573 tmp &= ~(P2C_RG_SUSPENDM | P2C_FORCE_SUSPENDM);
574 writel(tmp, com + U3P_U2PHYDTM0);
576 tmp = readl(com + U3D_U2PHYDCR0);
577 tmp &= ~P2C_RG_SIF_U2PLL_FORCE_ON;
578 writel(tmp, com + U3D_U2PHYDCR0);
581 dev_dbg(tphy->dev, "%s(%d)\n", __func__, index);
584 static void u2_phy_instance_exit(struct mtk_tphy *tphy,
585 struct mtk_phy_instance *instance)
587 struct u2phy_banks *u2_banks = &instance->u2_banks;
588 void __iomem *com = u2_banks->com;
589 u32 index = instance->index;
590 u32 tmp;
592 if (tphy->pdata->avoid_rx_sen_degradation && index) {
593 tmp = readl(com + U3D_U2PHYDCR0);
594 tmp &= ~P2C_RG_SIF_U2PLL_FORCE_ON;
595 writel(tmp, com + U3D_U2PHYDCR0);
597 tmp = readl(com + U3P_U2PHYDTM0);
598 tmp &= ~P2C_FORCE_SUSPENDM;
599 writel(tmp, com + U3P_U2PHYDTM0);
603 static void u2_phy_instance_set_mode(struct mtk_tphy *tphy,
604 struct mtk_phy_instance *instance,
605 enum phy_mode mode)
607 struct u2phy_banks *u2_banks = &instance->u2_banks;
608 u32 tmp;
610 tmp = readl(u2_banks->com + U3P_U2PHYDTM1);
611 switch (mode) {
612 case PHY_MODE_USB_DEVICE:
613 tmp |= P2C_FORCE_IDDIG | P2C_RG_IDDIG;
614 break;
615 case PHY_MODE_USB_HOST:
616 tmp |= P2C_FORCE_IDDIG;
617 tmp &= ~P2C_RG_IDDIG;
618 break;
619 case PHY_MODE_USB_OTG:
620 tmp &= ~(P2C_FORCE_IDDIG | P2C_RG_IDDIG);
621 break;
622 default:
623 return;
625 writel(tmp, u2_banks->com + U3P_U2PHYDTM1);
628 static void pcie_phy_instance_init(struct mtk_tphy *tphy,
629 struct mtk_phy_instance *instance)
631 struct u3phy_banks *u3_banks = &instance->u3_banks;
632 u32 tmp;
634 if (tphy->pdata->version != MTK_PHY_V1)
635 return;
637 tmp = readl(u3_banks->phya + U3P_U3_PHYA_DA_REG0);
638 tmp &= ~(P3A_RG_XTAL_EXT_PE1H | P3A_RG_XTAL_EXT_PE2H);
639 tmp |= P3A_RG_XTAL_EXT_PE1H_VAL(0x2) | P3A_RG_XTAL_EXT_PE2H_VAL(0x2);
640 writel(tmp, u3_banks->phya + U3P_U3_PHYA_DA_REG0);
642 /* ref clk drive */
643 tmp = readl(u3_banks->phya + U3P_U3_PHYA_REG1);
644 tmp &= ~P3A_RG_CLKDRV_AMP;
645 tmp |= P3A_RG_CLKDRV_AMP_VAL(0x4);
646 writel(tmp, u3_banks->phya + U3P_U3_PHYA_REG1);
648 tmp = readl(u3_banks->phya + U3P_U3_PHYA_REG0);
649 tmp &= ~P3A_RG_CLKDRV_OFF;
650 tmp |= P3A_RG_CLKDRV_OFF_VAL(0x1);
651 writel(tmp, u3_banks->phya + U3P_U3_PHYA_REG0);
653 /* SSC delta -5000ppm */
654 tmp = readl(u3_banks->phya + U3P_U3_PHYA_DA_REG20);
655 tmp &= ~P3A_RG_PLL_DELTA1_PE2H;
656 tmp |= P3A_RG_PLL_DELTA1_PE2H_VAL(0x3c);
657 writel(tmp, u3_banks->phya + U3P_U3_PHYA_DA_REG20);
659 tmp = readl(u3_banks->phya + U3P_U3_PHYA_DA_REG25);
660 tmp &= ~P3A_RG_PLL_DELTA_PE2H;
661 tmp |= P3A_RG_PLL_DELTA_PE2H_VAL(0x36);
662 writel(tmp, u3_banks->phya + U3P_U3_PHYA_DA_REG25);
664 /* change pll BW 0.6M */
665 tmp = readl(u3_banks->phya + U3P_U3_PHYA_DA_REG5);
666 tmp &= ~(P3A_RG_PLL_BR_PE2H | P3A_RG_PLL_IC_PE2H);
667 tmp |= P3A_RG_PLL_BR_PE2H_VAL(0x1) | P3A_RG_PLL_IC_PE2H_VAL(0x1);
668 writel(tmp, u3_banks->phya + U3P_U3_PHYA_DA_REG5);
670 tmp = readl(u3_banks->phya + U3P_U3_PHYA_DA_REG4);
671 tmp &= ~(P3A_RG_PLL_DIVEN_PE2H | P3A_RG_PLL_BC_PE2H);
672 tmp |= P3A_RG_PLL_BC_PE2H_VAL(0x3);
673 writel(tmp, u3_banks->phya + U3P_U3_PHYA_DA_REG4);
675 tmp = readl(u3_banks->phya + U3P_U3_PHYA_DA_REG6);
676 tmp &= ~P3A_RG_PLL_IR_PE2H;
677 tmp |= P3A_RG_PLL_IR_PE2H_VAL(0x2);
678 writel(tmp, u3_banks->phya + U3P_U3_PHYA_DA_REG6);
680 tmp = readl(u3_banks->phya + U3P_U3_PHYA_DA_REG7);
681 tmp &= ~P3A_RG_PLL_BP_PE2H;
682 tmp |= P3A_RG_PLL_BP_PE2H_VAL(0xa);
683 writel(tmp, u3_banks->phya + U3P_U3_PHYA_DA_REG7);
685 /* Tx Detect Rx Timing: 10us -> 5us */
686 tmp = readl(u3_banks->phyd + U3P_U3_PHYD_RXDET1);
687 tmp &= ~P3D_RG_RXDET_STB2_SET;
688 tmp |= P3D_RG_RXDET_STB2_SET_VAL(0x10);
689 writel(tmp, u3_banks->phyd + U3P_U3_PHYD_RXDET1);
691 tmp = readl(u3_banks->phyd + U3P_U3_PHYD_RXDET2);
692 tmp &= ~P3D_RG_RXDET_STB2_SET_P3;
693 tmp |= P3D_RG_RXDET_STB2_SET_P3_VAL(0x10);
694 writel(tmp, u3_banks->phyd + U3P_U3_PHYD_RXDET2);
696 /* wait for PCIe subsys register to active */
697 usleep_range(2500, 3000);
698 dev_dbg(tphy->dev, "%s(%d)\n", __func__, instance->index);
701 static void pcie_phy_instance_power_on(struct mtk_tphy *tphy,
702 struct mtk_phy_instance *instance)
704 struct u3phy_banks *bank = &instance->u3_banks;
705 u32 tmp;
707 tmp = readl(bank->chip + U3P_U3_CHIP_GPIO_CTLD);
708 tmp &= ~(P3C_FORCE_IP_SW_RST | P3C_REG_IP_SW_RST);
709 writel(tmp, bank->chip + U3P_U3_CHIP_GPIO_CTLD);
711 tmp = readl(bank->chip + U3P_U3_CHIP_GPIO_CTLE);
712 tmp &= ~(P3C_RG_SWRST_U3_PHYD_FORCE_EN | P3C_RG_SWRST_U3_PHYD);
713 writel(tmp, bank->chip + U3P_U3_CHIP_GPIO_CTLE);
716 static void pcie_phy_instance_power_off(struct mtk_tphy *tphy,
717 struct mtk_phy_instance *instance)
720 struct u3phy_banks *bank = &instance->u3_banks;
721 u32 tmp;
723 tmp = readl(bank->chip + U3P_U3_CHIP_GPIO_CTLD);
724 tmp |= P3C_FORCE_IP_SW_RST | P3C_REG_IP_SW_RST;
725 writel(tmp, bank->chip + U3P_U3_CHIP_GPIO_CTLD);
727 tmp = readl(bank->chip + U3P_U3_CHIP_GPIO_CTLE);
728 tmp |= P3C_RG_SWRST_U3_PHYD_FORCE_EN | P3C_RG_SWRST_U3_PHYD;
729 writel(tmp, bank->chip + U3P_U3_CHIP_GPIO_CTLE);
732 static void sata_phy_instance_init(struct mtk_tphy *tphy,
733 struct mtk_phy_instance *instance)
735 struct u3phy_banks *u3_banks = &instance->u3_banks;
736 void __iomem *phyd = u3_banks->phyd;
737 u32 tmp;
739 /* charge current adjustment */
740 tmp = readl(phyd + ANA_RG_CTRL_SIGNAL6);
741 tmp &= ~(RG_CDR_BIRLTR_GEN1_MSK | RG_CDR_BC_GEN1_MSK);
742 tmp |= RG_CDR_BIRLTR_GEN1_VAL(0x6) | RG_CDR_BC_GEN1_VAL(0x1a);
743 writel(tmp, phyd + ANA_RG_CTRL_SIGNAL6);
745 tmp = readl(phyd + ANA_EQ_EYE_CTRL_SIGNAL4);
746 tmp &= ~RG_CDR_BIRLTD0_GEN1_MSK;
747 tmp |= RG_CDR_BIRLTD0_GEN1_VAL(0x18);
748 writel(tmp, phyd + ANA_EQ_EYE_CTRL_SIGNAL4);
750 tmp = readl(phyd + ANA_EQ_EYE_CTRL_SIGNAL5);
751 tmp &= ~RG_CDR_BIRLTD0_GEN3_MSK;
752 tmp |= RG_CDR_BIRLTD0_GEN3_VAL(0x06);
753 writel(tmp, phyd + ANA_EQ_EYE_CTRL_SIGNAL5);
755 tmp = readl(phyd + ANA_RG_CTRL_SIGNAL4);
756 tmp &= ~(RG_CDR_BICLTR_GEN1_MSK | RG_CDR_BR_GEN2_MSK);
757 tmp |= RG_CDR_BICLTR_GEN1_VAL(0x0c) | RG_CDR_BR_GEN2_VAL(0x07);
758 writel(tmp, phyd + ANA_RG_CTRL_SIGNAL4);
760 tmp = readl(phyd + PHYD_CTRL_SIGNAL_MODE4);
761 tmp &= ~(RG_CDR_BICLTD0_GEN1_MSK | RG_CDR_BICLTD1_GEN1_MSK);
762 tmp |= RG_CDR_BICLTD0_GEN1_VAL(0x08) | RG_CDR_BICLTD1_GEN1_VAL(0x02);
763 writel(tmp, phyd + PHYD_CTRL_SIGNAL_MODE4);
765 tmp = readl(phyd + PHYD_DESIGN_OPTION2);
766 tmp &= ~RG_LOCK_CNT_SEL_MSK;
767 tmp |= RG_LOCK_CNT_SEL_VAL(0x02);
768 writel(tmp, phyd + PHYD_DESIGN_OPTION2);
770 tmp = readl(phyd + PHYD_DESIGN_OPTION9);
771 tmp &= ~(RG_T2_MIN_MSK | RG_TG_MIN_MSK |
772 RG_T2_MAX_MSK | RG_TG_MAX_MSK);
773 tmp |= RG_T2_MIN_VAL(0x12) | RG_TG_MIN_VAL(0x04) |
774 RG_T2_MAX_VAL(0x31) | RG_TG_MAX_VAL(0x0e);
775 writel(tmp, phyd + PHYD_DESIGN_OPTION9);
777 tmp = readl(phyd + ANA_RG_CTRL_SIGNAL1);
778 tmp &= ~RG_IDRV_0DB_GEN1_MSK;
779 tmp |= RG_IDRV_0DB_GEN1_VAL(0x20);
780 writel(tmp, phyd + ANA_RG_CTRL_SIGNAL1);
782 tmp = readl(phyd + ANA_EQ_EYE_CTRL_SIGNAL1);
783 tmp &= ~RG_EQ_DLEQ_LFI_GEN1_MSK;
784 tmp |= RG_EQ_DLEQ_LFI_GEN1_VAL(0x03);
785 writel(tmp, phyd + ANA_EQ_EYE_CTRL_SIGNAL1);
787 dev_dbg(tphy->dev, "%s(%d)\n", __func__, instance->index);
790 static void phy_v1_banks_init(struct mtk_tphy *tphy,
791 struct mtk_phy_instance *instance)
793 struct u2phy_banks *u2_banks = &instance->u2_banks;
794 struct u3phy_banks *u3_banks = &instance->u3_banks;
796 switch (instance->type) {
797 case PHY_TYPE_USB2:
798 u2_banks->misc = NULL;
799 u2_banks->fmreg = tphy->sif_base + SSUSB_SIFSLV_V1_U2FREQ;
800 u2_banks->com = instance->port_base + SSUSB_SIFSLV_V1_U2PHY_COM;
801 break;
802 case PHY_TYPE_USB3:
803 case PHY_TYPE_PCIE:
804 u3_banks->spllc = tphy->sif_base + SSUSB_SIFSLV_V1_SPLLC;
805 u3_banks->chip = tphy->sif_base + SSUSB_SIFSLV_V1_CHIP;
806 u3_banks->phyd = instance->port_base + SSUSB_SIFSLV_V1_U3PHYD;
807 u3_banks->phya = instance->port_base + SSUSB_SIFSLV_V1_U3PHYA;
808 break;
809 case PHY_TYPE_SATA:
810 u3_banks->phyd = instance->port_base + SSUSB_SIFSLV_V1_U3PHYD;
811 break;
812 default:
813 dev_err(tphy->dev, "incompatible PHY type\n");
814 return;
818 static void phy_v2_banks_init(struct mtk_tphy *tphy,
819 struct mtk_phy_instance *instance)
821 struct u2phy_banks *u2_banks = &instance->u2_banks;
822 struct u3phy_banks *u3_banks = &instance->u3_banks;
824 switch (instance->type) {
825 case PHY_TYPE_USB2:
826 u2_banks->misc = instance->port_base + SSUSB_SIFSLV_V2_MISC;
827 u2_banks->fmreg = instance->port_base + SSUSB_SIFSLV_V2_U2FREQ;
828 u2_banks->com = instance->port_base + SSUSB_SIFSLV_V2_U2PHY_COM;
829 break;
830 case PHY_TYPE_USB3:
831 case PHY_TYPE_PCIE:
832 u3_banks->spllc = instance->port_base + SSUSB_SIFSLV_V2_SPLLC;
833 u3_banks->chip = instance->port_base + SSUSB_SIFSLV_V2_CHIP;
834 u3_banks->phyd = instance->port_base + SSUSB_SIFSLV_V2_U3PHYD;
835 u3_banks->phya = instance->port_base + SSUSB_SIFSLV_V2_U3PHYA;
836 break;
837 default:
838 dev_err(tphy->dev, "incompatible PHY type\n");
839 return;
843 static void phy_parse_property(struct mtk_tphy *tphy,
844 struct mtk_phy_instance *instance)
846 struct device *dev = &instance->phy->dev;
848 if (instance->type != PHY_TYPE_USB2)
849 return;
851 instance->bc12_en = device_property_read_bool(dev, "mediatek,bc12");
852 device_property_read_u32(dev, "mediatek,eye-src",
853 &instance->eye_src);
854 device_property_read_u32(dev, "mediatek,eye-vrt",
855 &instance->eye_vrt);
856 device_property_read_u32(dev, "mediatek,eye-term",
857 &instance->eye_term);
858 device_property_read_u32(dev, "mediatek,intr",
859 &instance->intr);
860 device_property_read_u32(dev, "mediatek,discth",
861 &instance->discth);
862 dev_dbg(dev, "bc12:%d, src:%d, vrt:%d, term:%d, intr:%d, disc:%d\n",
863 instance->bc12_en, instance->eye_src,
864 instance->eye_vrt, instance->eye_term,
865 instance->intr, instance->discth);
868 static void u2_phy_props_set(struct mtk_tphy *tphy,
869 struct mtk_phy_instance *instance)
871 struct u2phy_banks *u2_banks = &instance->u2_banks;
872 void __iomem *com = u2_banks->com;
873 u32 tmp;
875 if (instance->bc12_en) {
876 tmp = readl(com + U3P_U2PHYBC12C);
877 tmp |= P2C_RG_CHGDT_EN; /* BC1.2 path Enable */
878 writel(tmp, com + U3P_U2PHYBC12C);
881 if (instance->eye_src) {
882 tmp = readl(com + U3P_USBPHYACR5);
883 tmp &= ~PA5_RG_U2_HSTX_SRCTRL;
884 tmp |= PA5_RG_U2_HSTX_SRCTRL_VAL(instance->eye_src);
885 writel(tmp, com + U3P_USBPHYACR5);
888 if (instance->eye_vrt) {
889 tmp = readl(com + U3P_USBPHYACR1);
890 tmp &= ~PA1_RG_VRT_SEL;
891 tmp |= PA1_RG_VRT_SEL_VAL(instance->eye_vrt);
892 writel(tmp, com + U3P_USBPHYACR1);
895 if (instance->eye_term) {
896 tmp = readl(com + U3P_USBPHYACR1);
897 tmp &= ~PA1_RG_TERM_SEL;
898 tmp |= PA1_RG_TERM_SEL_VAL(instance->eye_term);
899 writel(tmp, com + U3P_USBPHYACR1);
902 if (instance->intr) {
903 tmp = readl(com + U3P_USBPHYACR1);
904 tmp &= ~PA1_RG_INTR_CAL;
905 tmp |= PA1_RG_INTR_CAL_VAL(instance->intr);
906 writel(tmp, com + U3P_USBPHYACR1);
909 if (instance->discth) {
910 tmp = readl(com + U3P_USBPHYACR6);
911 tmp &= ~PA6_RG_U2_DISCTH;
912 tmp |= PA6_RG_U2_DISCTH_VAL(instance->discth);
913 writel(tmp, com + U3P_USBPHYACR6);
917 static int mtk_phy_init(struct phy *phy)
919 struct mtk_phy_instance *instance = phy_get_drvdata(phy);
920 struct mtk_tphy *tphy = dev_get_drvdata(phy->dev.parent);
921 int ret;
923 ret = clk_prepare_enable(instance->ref_clk);
924 if (ret) {
925 dev_err(tphy->dev, "failed to enable ref_clk\n");
926 return ret;
929 ret = clk_prepare_enable(instance->da_ref_clk);
930 if (ret) {
931 dev_err(tphy->dev, "failed to enable da_ref\n");
932 clk_disable_unprepare(instance->ref_clk);
933 return ret;
936 switch (instance->type) {
937 case PHY_TYPE_USB2:
938 u2_phy_instance_init(tphy, instance);
939 u2_phy_props_set(tphy, instance);
940 break;
941 case PHY_TYPE_USB3:
942 u3_phy_instance_init(tphy, instance);
943 break;
944 case PHY_TYPE_PCIE:
945 pcie_phy_instance_init(tphy, instance);
946 break;
947 case PHY_TYPE_SATA:
948 sata_phy_instance_init(tphy, instance);
949 break;
950 default:
951 dev_err(tphy->dev, "incompatible PHY type\n");
952 return -EINVAL;
955 return 0;
958 static int mtk_phy_power_on(struct phy *phy)
960 struct mtk_phy_instance *instance = phy_get_drvdata(phy);
961 struct mtk_tphy *tphy = dev_get_drvdata(phy->dev.parent);
963 if (instance->type == PHY_TYPE_USB2) {
964 u2_phy_instance_power_on(tphy, instance);
965 hs_slew_rate_calibrate(tphy, instance);
966 } else if (instance->type == PHY_TYPE_PCIE) {
967 pcie_phy_instance_power_on(tphy, instance);
970 return 0;
973 static int mtk_phy_power_off(struct phy *phy)
975 struct mtk_phy_instance *instance = phy_get_drvdata(phy);
976 struct mtk_tphy *tphy = dev_get_drvdata(phy->dev.parent);
978 if (instance->type == PHY_TYPE_USB2)
979 u2_phy_instance_power_off(tphy, instance);
980 else if (instance->type == PHY_TYPE_PCIE)
981 pcie_phy_instance_power_off(tphy, instance);
983 return 0;
986 static int mtk_phy_exit(struct phy *phy)
988 struct mtk_phy_instance *instance = phy_get_drvdata(phy);
989 struct mtk_tphy *tphy = dev_get_drvdata(phy->dev.parent);
991 if (instance->type == PHY_TYPE_USB2)
992 u2_phy_instance_exit(tphy, instance);
994 clk_disable_unprepare(instance->ref_clk);
995 clk_disable_unprepare(instance->da_ref_clk);
996 return 0;
999 static int mtk_phy_set_mode(struct phy *phy, enum phy_mode mode, int submode)
1001 struct mtk_phy_instance *instance = phy_get_drvdata(phy);
1002 struct mtk_tphy *tphy = dev_get_drvdata(phy->dev.parent);
1004 if (instance->type == PHY_TYPE_USB2)
1005 u2_phy_instance_set_mode(tphy, instance, mode);
1007 return 0;
1010 static struct phy *mtk_phy_xlate(struct device *dev,
1011 struct of_phandle_args *args)
1013 struct mtk_tphy *tphy = dev_get_drvdata(dev);
1014 struct mtk_phy_instance *instance = NULL;
1015 struct device_node *phy_np = args->np;
1016 int index;
1018 if (args->args_count != 1) {
1019 dev_err(dev, "invalid number of cells in 'phy' property\n");
1020 return ERR_PTR(-EINVAL);
1023 for (index = 0; index < tphy->nphys; index++)
1024 if (phy_np == tphy->phys[index]->phy->dev.of_node) {
1025 instance = tphy->phys[index];
1026 break;
1029 if (!instance) {
1030 dev_err(dev, "failed to find appropriate phy\n");
1031 return ERR_PTR(-EINVAL);
1034 instance->type = args->args[0];
1035 if (!(instance->type == PHY_TYPE_USB2 ||
1036 instance->type == PHY_TYPE_USB3 ||
1037 instance->type == PHY_TYPE_PCIE ||
1038 instance->type == PHY_TYPE_SATA)) {
1039 dev_err(dev, "unsupported device type: %d\n", instance->type);
1040 return ERR_PTR(-EINVAL);
1043 if (tphy->pdata->version == MTK_PHY_V1) {
1044 phy_v1_banks_init(tphy, instance);
1045 } else if (tphy->pdata->version == MTK_PHY_V2) {
1046 phy_v2_banks_init(tphy, instance);
1047 } else {
1048 dev_err(dev, "phy version is not supported\n");
1049 return ERR_PTR(-EINVAL);
1052 phy_parse_property(tphy, instance);
1054 return instance->phy;
1057 static const struct phy_ops mtk_tphy_ops = {
1058 .init = mtk_phy_init,
1059 .exit = mtk_phy_exit,
1060 .power_on = mtk_phy_power_on,
1061 .power_off = mtk_phy_power_off,
1062 .set_mode = mtk_phy_set_mode,
1063 .owner = THIS_MODULE,
1066 static const struct mtk_phy_pdata tphy_v1_pdata = {
1067 .avoid_rx_sen_degradation = false,
1068 .version = MTK_PHY_V1,
1071 static const struct mtk_phy_pdata tphy_v2_pdata = {
1072 .avoid_rx_sen_degradation = false,
1073 .version = MTK_PHY_V2,
1076 static const struct mtk_phy_pdata mt8173_pdata = {
1077 .avoid_rx_sen_degradation = true,
1078 .version = MTK_PHY_V1,
1081 static const struct of_device_id mtk_tphy_id_table[] = {
1082 { .compatible = "mediatek,mt2701-u3phy", .data = &tphy_v1_pdata },
1083 { .compatible = "mediatek,mt2712-u3phy", .data = &tphy_v2_pdata },
1084 { .compatible = "mediatek,mt8173-u3phy", .data = &mt8173_pdata },
1085 { .compatible = "mediatek,generic-tphy-v1", .data = &tphy_v1_pdata },
1086 { .compatible = "mediatek,generic-tphy-v2", .data = &tphy_v2_pdata },
1087 { },
1089 MODULE_DEVICE_TABLE(of, mtk_tphy_id_table);
1091 static int mtk_tphy_probe(struct platform_device *pdev)
1093 struct device *dev = &pdev->dev;
1094 struct device_node *np = dev->of_node;
1095 struct device_node *child_np;
1096 struct phy_provider *provider;
1097 struct resource *sif_res;
1098 struct mtk_tphy *tphy;
1099 struct resource res;
1100 int port, retval;
1102 tphy = devm_kzalloc(dev, sizeof(*tphy), GFP_KERNEL);
1103 if (!tphy)
1104 return -ENOMEM;
1106 tphy->pdata = of_device_get_match_data(dev);
1107 if (!tphy->pdata)
1108 return -EINVAL;
1110 tphy->nphys = of_get_child_count(np);
1111 tphy->phys = devm_kcalloc(dev, tphy->nphys,
1112 sizeof(*tphy->phys), GFP_KERNEL);
1113 if (!tphy->phys)
1114 return -ENOMEM;
1116 tphy->dev = dev;
1117 platform_set_drvdata(pdev, tphy);
1119 sif_res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
1120 /* SATA phy of V1 needn't it if not shared with PCIe or USB */
1121 if (sif_res && tphy->pdata->version == MTK_PHY_V1) {
1122 /* get banks shared by multiple phys */
1123 tphy->sif_base = devm_ioremap_resource(dev, sif_res);
1124 if (IS_ERR(tphy->sif_base)) {
1125 dev_err(dev, "failed to remap sif regs\n");
1126 return PTR_ERR(tphy->sif_base);
1130 tphy->src_ref_clk = U3P_REF_CLK;
1131 tphy->src_coef = U3P_SLEW_RATE_COEF;
1132 /* update parameters of slew rate calibrate if exist */
1133 device_property_read_u32(dev, "mediatek,src-ref-clk-mhz",
1134 &tphy->src_ref_clk);
1135 device_property_read_u32(dev, "mediatek,src-coef", &tphy->src_coef);
1137 port = 0;
1138 for_each_child_of_node(np, child_np) {
1139 struct mtk_phy_instance *instance;
1140 struct phy *phy;
1142 instance = devm_kzalloc(dev, sizeof(*instance), GFP_KERNEL);
1143 if (!instance) {
1144 retval = -ENOMEM;
1145 goto put_child;
1148 tphy->phys[port] = instance;
1150 phy = devm_phy_create(dev, child_np, &mtk_tphy_ops);
1151 if (IS_ERR(phy)) {
1152 dev_err(dev, "failed to create phy\n");
1153 retval = PTR_ERR(phy);
1154 goto put_child;
1157 retval = of_address_to_resource(child_np, 0, &res);
1158 if (retval) {
1159 dev_err(dev, "failed to get address resource(id-%d)\n",
1160 port);
1161 goto put_child;
1164 instance->port_base = devm_ioremap_resource(&phy->dev, &res);
1165 if (IS_ERR(instance->port_base)) {
1166 dev_err(dev, "failed to remap phy regs\n");
1167 retval = PTR_ERR(instance->port_base);
1168 goto put_child;
1171 instance->phy = phy;
1172 instance->index = port;
1173 phy_set_drvdata(phy, instance);
1174 port++;
1176 instance->ref_clk = devm_clk_get_optional(&phy->dev, "ref");
1177 if (IS_ERR(instance->ref_clk)) {
1178 dev_err(dev, "failed to get ref_clk(id-%d)\n", port);
1179 retval = PTR_ERR(instance->ref_clk);
1180 goto put_child;
1183 instance->da_ref_clk =
1184 devm_clk_get_optional(&phy->dev, "da_ref");
1185 if (IS_ERR(instance->da_ref_clk)) {
1186 dev_err(dev, "failed to get da_ref_clk(id-%d)\n", port);
1187 retval = PTR_ERR(instance->da_ref_clk);
1188 goto put_child;
1192 provider = devm_of_phy_provider_register(dev, mtk_phy_xlate);
1194 return PTR_ERR_OR_ZERO(provider);
1195 put_child:
1196 of_node_put(child_np);
1197 return retval;
1200 static struct platform_driver mtk_tphy_driver = {
1201 .probe = mtk_tphy_probe,
1202 .driver = {
1203 .name = "mtk-tphy",
1204 .of_match_table = mtk_tphy_id_table,
1208 module_platform_driver(mtk_tphy_driver);
1210 MODULE_AUTHOR("Chunfeng Yun <chunfeng.yun@mediatek.com>");
1211 MODULE_DESCRIPTION("MediaTek T-PHY driver");
1212 MODULE_LICENSE("GPL v2");