Linux 5.7.6

[linux/fpc-iii.git] / arch / mips / pci / ops-pmcmsp.c

// SPDX-License-Identifier: GPL-2.0-or-later
/*
 * PMC-Sierra MSP board specific pci_ops
 *
 * Copyright 2001 MontaVista Software Inc.
 * Copyright 2005-2007 PMC-Sierra, Inc
 *
 * Author: Jun Sun, jsun@mvista.com or jsun@junsun.net
 *
 * Much of the code is derived from the original DDB5074 port by
 * Geert Uytterhoeven <geert@linux-m68k.org>
 */

#define PCI_COUNTERS    1

#include <linux/types.h>
#include <linux/pci.h>
#include <linux/interrupt.h>

#if defined(CONFIG_PROC_FS) && defined(PCI_COUNTERS)
#include <linux/proc_fs.h>
#include <linux/seq_file.h>
#endif /* CONFIG_PROC_FS && PCI_COUNTERS */

#include <linux/kernel.h>
#include <linux/init.h>

#include <asm/byteorder.h>
#if defined(CONFIG_PMC_MSP7120_GW) || defined(CONFIG_PMC_MSP7120_EVAL)
#include <asm/mipsmtregs.h>
#endif

#include <msp_prom.h>
#include <msp_cic_int.h>
#include <msp_pci.h>
#include <msp_regs.h>
#include <msp_regops.h>

#define PCI_ACCESS_READ         0
#define PCI_ACCESS_WRITE        1

#if defined(CONFIG_PROC_FS) && defined(PCI_COUNTERS)
static char proc_init;
extern struct proc_dir_entry *proc_bus_pci_dir;
unsigned int pci_int_count[32];

static void pci_proc_init(void);

/*****************************************************************************
 *
 *  FUNCTION: show_msp_pci_counts
 *  _________________________________________________________________________
 *
 *  DESCRIPTION: Prints the count of how many times each PCI
 *               interrupt has asserted. Can be invoked by the
 *               /proc filesystem.
 *
 *  INPUTS:      m       - synthetic file construction data
 *               v       - iterator
 *
 *  RETURNS:     0 or error
 *
 ****************************************************************************/
static int show_msp_pci_counts(struct seq_file *m, void *v)
{
        int i;
        unsigned int intcount, total = 0;

        for (i = 0; i < 32; ++i) {
                intcount = pci_int_count[i];
                if (intcount != 0) {
                        seq_printf(m, "[%d] = %u\n", i, intcount);
                        total += intcount;
                }
        }

        seq_printf(m, "total = %u\n", total);
        return 0;
}

/*****************************************************************************
 *
 *  FUNCTION: gen_pci_cfg_wr_show
 *  _________________________________________________________________________
 *
 *  DESCRIPTION: Generates a configuration write cycle for debug purposes.
 *               The IDSEL line asserted and location and data written are
 *               immaterial. Just want to be able to prove that a
 *               configuration write can be correctly generated on the
 *               PCI bus.  Intent is that this function by invocable from
 *               the /proc filesystem.
 *
 *  INPUTS:      m       - synthetic file construction data
 *               v       - iterator
 *
 *  RETURNS:     0 or error
 *
 ****************************************************************************/
static int gen_pci_cfg_wr_show(struct seq_file *m, void *v)
{
        unsigned char where = 0; /* Write to static Device/Vendor ID */
        unsigned char bus_num = 0; /* Bus 0 */
        unsigned char dev_fn = 0xF; /* Arbitrary device number */
        u32 wr_data = 0xFF00AA00; /* Arbitrary data */
        struct msp_pci_regs *preg = (void *)PCI_BASE_REG;
        unsigned long value;
        int intr;

        seq_puts(m, "PMC MSP PCI: Beginning\n");

        if (proc_init == 0) {
                pci_proc_init();
                proc_init = ~0;
        }

        seq_puts(m, "PMC MSP PCI: Before Cfg Wr\n");

        /*
         * Generate PCI Configuration Write Cycle
         */

        /* Clear cause register bits */
        preg->if_status = ~(BPCI_IFSTATUS_BC0F | BPCI_IFSTATUS_BC1F);

        /* Setup address that is to appear on PCI bus */
        preg->config_addr = BPCI_CFGADDR_ENABLE |
                (bus_num << BPCI_CFGADDR_BUSNUM_SHF) |
                (dev_fn << BPCI_CFGADDR_FUNCTNUM_SHF) |
                (where & 0xFC);

        value = cpu_to_le32(wr_data);

        /* Launch the PCI configuration write cycle */
        *PCI_CONFIG_SPACE_REG = value;

        /*
         * Check if the PCI configuration cycle (rd or wr) succeeded, by
         * checking the status bits for errors like master or target abort.
         */
        intr = preg->if_status;

        seq_puts(m, "PMC MSP PCI: After Cfg Wr\n");
        return 0;
}

/*****************************************************************************
 *
 *  FUNCTION: pci_proc_init
 *  _________________________________________________________________________
 *
 *  DESCRIPTION: Create entries in the /proc filesystem for debug access.
 *
 *  INPUTS:      none
 *
 *  OUTPUTS:     none
 *
 *  RETURNS:     none
 *
 ****************************************************************************/
static void pci_proc_init(void)
{
        proc_create_single("pmc_msp_pci_rd_cnt", 0, NULL, show_msp_pci_counts);
        proc_create_single("pmc_msp_pci_cfg_wr", 0, NULL, gen_pci_cfg_wr_show);
}
#endif /* CONFIG_PROC_FS && PCI_COUNTERS */

/*****************************************************************************
 *
 *  STRUCT: pci_io_resource
 *  _________________________________________________________________________
 *
 *  DESCRIPTION: Defines the address range that pciauto() will use to
 *               assign to the I/O BARs of PCI devices.
 *
 *               Use the start and end addresses of the MSP7120 PCI Host
 *               Controller I/O space, in the form that they appear on the
 *               PCI bus AFTER MSP7120 has performed address translation.
 *
 *               For I/O accesses, MSP7120 ignores OATRAN and maps I/O
 *               accesses into the bottom 0xFFF region of address space,
 *               so that is the range to put into the pci_io_resource
 *               struct.
 *
 *               In MSP4200, the start address was 0x04 instead of the
 *               expected 0x00. Will just assume there was a good reason
 *               for this!
 *
 *  NOTES:       Linux, by default, will assign I/O space to the lowest
 *               region of address space. Since MSP7120 and Linux,
 *               by default, have no offset in between how they map, the
 *               io_offset element of pci_controller struct should be set
 *               to zero.
 *  ELEMENTS:
 *    name       - String used for a meaningful name.
 *
 *    start      - Start address of MSP7120's I/O space, as MSP7120 presents
 *                 the address on the PCI bus.
 *
 *    end        - End address of MSP7120's I/O space, as MSP7120 presents
 *                 the address on the PCI bus.
 *
 *    flags      - Attributes indicating the type of resource. In this case,
 *                 indicate I/O space.
 *
 ****************************************************************************/
static struct resource pci_io_resource = {
        .name   = "pci IO space",
        .start  = 0x04,
        .end    = 0x0FFF,
        .flags  = IORESOURCE_IO /* I/O space */
};

/*****************************************************************************
 *
 *  STRUCT: pci_mem_resource
 *  _________________________________________________________________________
 *
 *  DESCRIPTION: Defines the address range that pciauto() will use to
 *               assign to the memory BARs of PCI devices.
 *
 *               The .start and .end values are dependent upon how address
 *               translation is performed by the OATRAN regiser.
 *
 *               The values to use for .start and .end are the values
 *               in the form they appear on the PCI bus AFTER MSP7120 has
 *               performed OATRAN address translation.
 *
 *  ELEMENTS:
 *    name       - String used for a meaningful name.
 *
 *    start      - Start address of MSP7120's memory space, as MSP7120 presents
 *                 the address on the PCI bus.
 *
 *    end        - End address of MSP7120's memory space, as MSP7120 presents
 *                 the address on the PCI bus.
 *
 *    flags      - Attributes indicating the type of resource. In this case,
 *                 indicate memory space.
 *
 ****************************************************************************/
static struct resource pci_mem_resource = {
        .name   = "pci memory space",
        .start  = MSP_PCI_SPACE_BASE,
        .end    = MSP_PCI_SPACE_END,
        .flags  = IORESOURCE_MEM         /* memory space */
};

/*****************************************************************************
 *
 *  FUNCTION: bpci_interrupt
 *  _________________________________________________________________________
 *
 *  DESCRIPTION: PCI status interrupt handler. Updates the count of how
 *               many times each status bit has been set, then clears
 *               the status bits. If the appropriate macros are defined,
 *               these counts can be viewed via the /proc filesystem.
 *
 *  INPUTS:      irq     - unused
 *               dev_id  - unused
 *               pt_regs - unused
 *
 *  OUTPUTS:     none
 *
 *  RETURNS:     PCIBIOS_SUCCESSFUL  - success
 *
 ****************************************************************************/
static irqreturn_t bpci_interrupt(int irq, void *dev_id)
{
        struct msp_pci_regs *preg = (void *)PCI_BASE_REG;
        unsigned int stat = preg->if_status;

#if defined(CONFIG_PROC_FS) && defined(PCI_COUNTERS)
        int i;
        for (i = 0; i < 32; ++i) {
                if ((1 << i) & stat)
                        ++pci_int_count[i];
        }
#endif /* PROC_FS && PCI_COUNTERS */

        /* printk("PCI ISR: Status=%08X\n", stat); */

        /* write to clear all asserted interrupts */
        preg->if_status = stat;

        return IRQ_HANDLED;
}

/*****************************************************************************
 *
 *  FUNCTION: msp_pcibios_config_access
 *  _________________________________________________________________________
 *
 *  DESCRIPTION: Performs a PCI configuration access (rd or wr), then
 *               checks that the access succeeded by querying MSP7120's
 *               PCI status bits.
 *
 *  INPUTS:
 *               access_type  - kind of PCI configuration cycle to perform
 *                              (read or write). Legal values are
 *                              PCI_ACCESS_WRITE and PCI_ACCESS_READ.
 *
 *               bus          - pointer to the bus number of the device to
 *                              be targeted for the configuration cycle.
 *                              The only element of the pci_bus structure
 *                              used is bus->number. This argument determines
 *                              if the configuration access will be Type 0 or
 *                              Type 1. Since MSP7120 assumes itself to be the
 *                              PCI Host, any non-zero bus->number generates
 *                              a Type 1 access.
 *
 *               devfn        - this is an 8-bit field. The lower three bits
 *                              specify the function number of the device to
 *                              be targeted for the configuration cycle, with
 *                              all three-bit combinations being legal. The
 *                              upper five bits specify the device number,
 *                              with legal values being 10 to 31.
 *
 *               where        - address within the Configuration Header
 *                              space to access.
 *
 *               data         - for write accesses, contains the data to
 *                              write.
 *
 *  OUTPUTS:
 *               data         - for read accesses, contains the value read.
 *
 *  RETURNS:     PCIBIOS_SUCCESSFUL  - success
 *               -1                  - access failure
 *
 ****************************************************************************/
int msp_pcibios_config_access(unsigned char access_type,
                                struct pci_bus *bus,
                                unsigned int devfn,
                                unsigned char where,
                                u32 *data)
{
        struct msp_pci_regs *preg = (void *)PCI_BASE_REG;
        unsigned char bus_num = bus->number;
        unsigned char dev_fn = (unsigned char)devfn;
        unsigned long intr;
        unsigned long value;
        static char pciirqflag;
        int ret;
#if defined(CONFIG_PMC_MSP7120_GW) || defined(CONFIG_PMC_MSP7120_EVAL)
        unsigned int    vpe_status;
#endif

#if defined(CONFIG_PROC_FS) && defined(PCI_COUNTERS)
        if (proc_init == 0) {
                pci_proc_init();
                proc_init = ~0;
        }
#endif /* CONFIG_PROC_FS && PCI_COUNTERS */

        /*
         * Just the first time this function invokes, allocate
         * an interrupt line for PCI host status interrupts. The
         * allocation assigns an interrupt handler to the interrupt.
         */
        if (pciirqflag == 0) {
                ret = request_irq(MSP_INT_PCI,/* Hardcoded internal MSP7120 wiring */
                                bpci_interrupt,
                                IRQF_SHARED,
                                "PMC MSP PCI Host",
                                preg);
                if (ret != 0)
                        return ret;
                pciirqflag = ~0;
        }

#if defined(CONFIG_PMC_MSP7120_GW) || defined(CONFIG_PMC_MSP7120_EVAL)
        vpe_status = dvpe();
#endif

        /*
         * Clear PCI cause register bits.
         *
         * In Polo, the PCI Host had a dedicated DMA called the
         * Block Copy (not to be confused with the general purpose Block
         * Copy Engine block). There appear to have been special interrupts
         * for this Block Copy, called Block Copy 0 Fault (BC0F) and
         * Block Copy 1 Fault (BC1F). MSP4200 and MSP7120 don't have this
         * dedicated Block Copy block, so these two interrupts are now
         * marked reserved. In case the  Block Copy is resurrected in a
         * future design, maintain the code that treats these two interrupts
         * specially.
         *
         * Write to clear all interrupts in the PCI status register, aside
         * from BC0F and BC1F.
         */
        preg->if_status = ~(BPCI_IFSTATUS_BC0F | BPCI_IFSTATUS_BC1F);

        /* Setup address that is to appear on PCI bus */
        preg->config_addr = BPCI_CFGADDR_ENABLE |
                (bus_num << BPCI_CFGADDR_BUSNUM_SHF) |
                (dev_fn << BPCI_CFGADDR_FUNCTNUM_SHF) |
                (where & 0xFC);

        /* IF access is a PCI configuration write */
        if (access_type == PCI_ACCESS_WRITE) {
                value = cpu_to_le32(*data);
                *PCI_CONFIG_SPACE_REG = value;
        } else {
                /* ELSE access is a PCI configuration read */
                value = le32_to_cpu(*PCI_CONFIG_SPACE_REG);
                *data = value;
        }

        /*
         * Check if the PCI configuration cycle (rd or wr) succeeded, by
         * checking the status bits for errors like master or target abort.
         */
        intr = preg->if_status;

        /* Clear config access */
        preg->config_addr = 0;

        /* IF error occurred */
        if (intr & ~(BPCI_IFSTATUS_BC0F | BPCI_IFSTATUS_BC1F)) {
                /* Clear status bits */
                preg->if_status = ~(BPCI_IFSTATUS_BC0F | BPCI_IFSTATUS_BC1F);

#if defined(CONFIG_PMC_MSP7120_GW) || defined(CONFIG_PMC_MSP7120_EVAL)
                evpe(vpe_status);
#endif

                return -1;
        }

#if defined(CONFIG_PMC_MSP7120_GW) || defined(CONFIG_PMC_MSP7120_EVAL)
        evpe(vpe_status);
#endif

        return PCIBIOS_SUCCESSFUL;
}

/*****************************************************************************
 *
 *  FUNCTION: msp_pcibios_read_config_byte
 *  _________________________________________________________________________
 *
 *  DESCRIPTION: Read a byte from PCI configuration address spac
 *               Since the hardware can't address 8 bit chunks
 *               directly, read a 32-bit chunk, then mask off extraneous
 *               bits.
 *
 *  INPUTS       bus    - structure containing attributes for the PCI bus
 *                        that the read is destined for.
 *               devfn  - device/function combination that the read is
 *                        destined for.
 *               where  - register within the Configuration Header space
 *                        to access.
 *
 *  OUTPUTS      val    - read data
 *
 *  RETURNS:     PCIBIOS_SUCCESSFUL  - success
 *               -1                  - read access failure
 *
 ****************************************************************************/
static int
msp_pcibios_read_config_byte(struct pci_bus *bus,
                                unsigned int devfn,
                                int where,
                                u32 *val)
{
        u32 data = 0;

        /*
         * If the config access did not complete normally (e.g., underwent
         * master abort) do the PCI compliant thing, which is to supply an
         * all ones value.
         */
        if (msp_pcibios_config_access(PCI_ACCESS_READ, bus, devfn,
                                        where, &data)) {
                *val = 0xFFFFFFFF;
                return -1;
        }

        *val = (data >> ((where & 3) << 3)) & 0x0ff;

        return PCIBIOS_SUCCESSFUL;
}

/*****************************************************************************
 *
 *  FUNCTION: msp_pcibios_read_config_word
 *  _________________________________________________________________________
 *
 *  DESCRIPTION: Read a word (16 bits) from PCI configuration address space.
 *               Since the hardware can't address 16 bit chunks
 *               directly, read a 32-bit chunk, then mask off extraneous
 *               bits.
 *
 *  INPUTS       bus    - structure containing attributes for the PCI bus
 *                        that the read is destined for.
 *               devfn  - device/function combination that the read is
 *                        destined for.
 *               where  - register within the Configuration Header space
 *                        to access.
 *
 *  OUTPUTS      val    - read data
 *
 *  RETURNS:     PCIBIOS_SUCCESSFUL           - success
 *               PCIBIOS_BAD_REGISTER_NUMBER  - bad register address
 *               -1                           - read access failure
 *
 ****************************************************************************/
static int
msp_pcibios_read_config_word(struct pci_bus *bus,
                                unsigned int devfn,
                                int where,
                                u32 *val)
{
        u32 data = 0;

        /* if (where & 1) */    /* Commented out non-compliant code.
                                 * Should allow word access to configuration
                                 * registers, with only exception being when
                                 * the word access would wrap around into
                                 * the next dword.
                                 */
        if ((where & 3) == 3) {
                *val = 0xFFFFFFFF;
                return PCIBIOS_BAD_REGISTER_NUMBER;
        }

        /*
         * If the config access did not complete normally (e.g., underwent
         * master abort) do the PCI compliant thing, which is to supply an
         * all ones value.
         */
        if (msp_pcibios_config_access(PCI_ACCESS_READ, bus, devfn,
                                        where, &data)) {
                *val = 0xFFFFFFFF;
                return -1;
        }

        *val = (data >> ((where & 3) << 3)) & 0x0ffff;

        return PCIBIOS_SUCCESSFUL;
}

/*****************************************************************************
 *
 *  FUNCTION: msp_pcibios_read_config_dword
 *  _________________________________________________________________________
 *
 *  DESCRIPTION: Read a double word (32 bits) from PCI configuration
 *               address space.
 *
 *  INPUTS       bus    - structure containing attributes for the PCI bus
 *                        that the read is destined for.
 *               devfn  - device/function combination that the read is
 *                        destined for.
 *               where  - register within the Configuration Header space
 *                        to access.
 *
 *  OUTPUTS      val    - read data
 *
 *  RETURNS:     PCIBIOS_SUCCESSFUL           - success
 *               PCIBIOS_BAD_REGISTER_NUMBER  - bad register address
 *               -1                           - read access failure
 *
 ****************************************************************************/
static int
msp_pcibios_read_config_dword(struct pci_bus *bus,
                                unsigned int devfn,
                                int where,
                                u32 *val)
{
        u32 data = 0;

        /* Address must be dword aligned. */
        if (where & 3) {
                *val = 0xFFFFFFFF;
                return PCIBIOS_BAD_REGISTER_NUMBER;
        }

        /*
         * If the config access did not complete normally (e.g., underwent
         * master abort) do the PCI compliant thing, which is to supply an
         * all ones value.
         */
        if (msp_pcibios_config_access(PCI_ACCESS_READ, bus, devfn,
                                        where, &data)) {
                *val = 0xFFFFFFFF;
                return -1;
        }

        *val = data;

        return PCIBIOS_SUCCESSFUL;
}

/*****************************************************************************
 *
 *  FUNCTION: msp_pcibios_write_config_byte
 *  _________________________________________________________________________
 *
 *  DESCRIPTION: Write a byte to PCI configuration address space.
 *               Since the hardware can't address 8 bit chunks
 *               directly, a read-modify-write is performed.
 *
 *  INPUTS       bus    - structure containing attributes for the PCI bus
 *                        that the write is destined for.
 *               devfn  - device/function combination that the write is
 *                        destined for.
 *               where  - register within the Configuration Header space
 *                        to access.
 *               val    - value to write
 *
 *  OUTPUTS      none
 *
 *  RETURNS:     PCIBIOS_SUCCESSFUL  - success
 *               -1                  - write access failure
 *
 ****************************************************************************/
static int
msp_pcibios_write_config_byte(struct pci_bus *bus,
                                unsigned int devfn,
                                int where,
                                u8 val)
{
        u32 data = 0;

        /* read config space */
        if (msp_pcibios_config_access(PCI_ACCESS_READ, bus, devfn,
                                        where, &data))
                return -1;

        /* modify the byte within the dword */
        data = (data & ~(0xff << ((where & 3) << 3))) |
                        (val << ((where & 3) << 3));

        /* write back the full dword */
        if (msp_pcibios_config_access(PCI_ACCESS_WRITE, bus, devfn,
                                        where, &data))
                return -1;

        return PCIBIOS_SUCCESSFUL;
}

/*****************************************************************************
 *
 *  FUNCTION: msp_pcibios_write_config_word
 *  _________________________________________________________________________
 *
 *  DESCRIPTION: Write a word (16-bits) to PCI configuration address space.
 *               Since the hardware can't address 16 bit chunks
 *               directly, a read-modify-write is performed.
 *
 *  INPUTS       bus    - structure containing attributes for the PCI bus
 *                        that the write is destined for.
 *               devfn  - device/function combination that the write is
 *                        destined for.
 *               where  - register within the Configuration Header space
 *                        to access.
 *               val    - value to write
 *
 *  OUTPUTS      none
 *
 *  RETURNS:     PCIBIOS_SUCCESSFUL           - success
 *               PCIBIOS_BAD_REGISTER_NUMBER  - bad register address
 *               -1                           - write access failure
 *
 ****************************************************************************/
static int
msp_pcibios_write_config_word(struct pci_bus *bus,
                                unsigned int devfn,
                                int where,
                                u16 val)
{
        u32 data = 0;

        /* Fixed non-compliance: if (where & 1) */
        if ((where & 3) == 3)
                return PCIBIOS_BAD_REGISTER_NUMBER;

        /* read config space */
        if (msp_pcibios_config_access(PCI_ACCESS_READ, bus, devfn,
                                        where, &data))
                return -1;

        /* modify the word within the dword */
        data = (data & ~(0xffff << ((where & 3) << 3))) |
                        (val << ((where & 3) << 3));

        /* write back the full dword */
        if (msp_pcibios_config_access(PCI_ACCESS_WRITE, bus, devfn,
                                        where, &data))
                return -1;

        return PCIBIOS_SUCCESSFUL;
}

/*****************************************************************************
 *
 *  FUNCTION: msp_pcibios_write_config_dword
 *  _________________________________________________________________________
 *
 *  DESCRIPTION: Write a double word (32-bits) to PCI configuration address
 *               space.
 *
 *  INPUTS       bus    - structure containing attributes for the PCI bus
 *                        that the write is destined for.
 *               devfn  - device/function combination that the write is
 *                        destined for.
 *               where  - register within the Configuration Header space
 *                        to access.
 *               val    - value to write
 *
 *  OUTPUTS      none
 *
 *  RETURNS:     PCIBIOS_SUCCESSFUL           - success
 *               PCIBIOS_BAD_REGISTER_NUMBER  - bad register address
 *               -1                           - write access failure
 *
 ****************************************************************************/
static int
msp_pcibios_write_config_dword(struct pci_bus *bus,
                                unsigned int devfn,
                                int where,
                                u32 val)
{
        /* check that address is dword aligned */
        if (where & 3)
                return PCIBIOS_BAD_REGISTER_NUMBER;

        /* perform write */
        if (msp_pcibios_config_access(PCI_ACCESS_WRITE, bus, devfn,
                                        where, &val))
                return -1;

        return PCIBIOS_SUCCESSFUL;
}

/*****************************************************************************
 *
 *  FUNCTION: msp_pcibios_read_config
 *  _________________________________________________________________________
 *
 *  DESCRIPTION: Interface the PCI configuration read request with
 *               the appropriate function, based on how many bytes
 *               the read request is.
 *
 *  INPUTS       bus    - structure containing attributes for the PCI bus
 *                        that the write is destined for.
 *               devfn  - device/function combination that the write is
 *                        destined for.
 *               where  - register within the Configuration Header space
 *                        to access.
 *               size   - in units of bytes, should be 1, 2, or 4.
 *
 *  OUTPUTS      val    - value read, with any extraneous bytes masked
 *                        to zero.
 *
 *  RETURNS:     PCIBIOS_SUCCESSFUL   - success
 *               -1                   - failure
 *
 ****************************************************************************/
int
msp_pcibios_read_config(struct pci_bus *bus,
                        unsigned int    devfn,
                        int where,
                        int size,
                        u32 *val)
{
        if (size == 1) {
                if (msp_pcibios_read_config_byte(bus, devfn, where, val)) {
                        return -1;
                }
        } else if (size == 2) {
                if (msp_pcibios_read_config_word(bus, devfn, where, val)) {
                        return -1;
                }
        } else if (size == 4) {
                if (msp_pcibios_read_config_dword(bus, devfn, where, val)) {
                        return -1;
                }
        } else {
                *val = 0xFFFFFFFF;
                return -1;
        }

        return PCIBIOS_SUCCESSFUL;
}

/*****************************************************************************
 *
 *  FUNCTION: msp_pcibios_write_config
 *  _________________________________________________________________________
 *
 *  DESCRIPTION: Interface the PCI configuration write request with
 *               the appropriate function, based on how many bytes
 *               the read request is.
 *
 *  INPUTS       bus    - structure containing attributes for the PCI bus
 *                        that the write is destined for.
 *               devfn  - device/function combination that the write is
 *                        destined for.
 *               where  - register within the Configuration Header space
 *                        to access.
 *               size   - in units of bytes, should be 1, 2, or 4.
 *               val    - value to write
 *
 *  OUTPUTS:     none
 *
 *  RETURNS:     PCIBIOS_SUCCESSFUL   - success
 *               -1                   - failure
 *
 ****************************************************************************/
int
msp_pcibios_write_config(struct pci_bus *bus,
                        unsigned int devfn,
                        int where,
                        int size,
                        u32 val)
{
        if (size == 1) {
                if (msp_pcibios_write_config_byte(bus, devfn,
                                                where, (u8)(0xFF & val))) {
                        return -1;
                }
        } else if (size == 2) {
                if (msp_pcibios_write_config_word(bus, devfn,
                                                where, (u16)(0xFFFF & val))) {
                        return -1;
                }
        } else if (size == 4) {
                if (msp_pcibios_write_config_dword(bus, devfn, where, val)) {
                        return -1;
                }
        } else {
                return -1;
        }

        return PCIBIOS_SUCCESSFUL;
}

/*****************************************************************************
 *
 *  STRUCTURE: msp_pci_ops
 *  _________________________________________________________________________
 *
 *  DESCRIPTION: structure to abstract the hardware specific PCI
 *               configuration accesses.
 *
 *  ELEMENTS:
 *    read      - function for Linux to generate PCI Configuration reads.
 *    write     - function for Linux to generate PCI Configuration writes.
 *
 ****************************************************************************/
struct pci_ops msp_pci_ops = {
        .read = msp_pcibios_read_config,
        .write = msp_pcibios_write_config
};

/*****************************************************************************
 *
 *  STRUCTURE: msp_pci_controller
 *  _________________________________________________________________________
 *
 *  Describes the attributes of the MSP7120 PCI Host Controller
 *
 *  ELEMENTS:
 *    pci_ops      - abstracts the hardware specific PCI configuration
 *                   accesses.
 *
 *    mem_resource - address range pciauto() uses to assign to PCI device
 *                   memory BARs.
 *
 *    mem_offset   - offset between how MSP7120 outbound PCI memory
 *                   transaction addresses appear on the PCI bus and how Linux
 *                   wants to configure memory BARs of the PCI devices.
 *                   MSP7120 does nothing funky, so just set to zero.
 *
 *    io_resource  - address range pciauto() uses to assign to PCI device
 *                   I/O BARs.
 *
 *    io_offset    - offset between how MSP7120 outbound PCI I/O
 *                   transaction addresses appear on the PCI bus and how
 *                   Linux defaults to configure I/O BARs of the PCI devices.
 *                   MSP7120 maps outbound I/O accesses into the bottom
 *                   bottom 4K of PCI address space (and ignores OATRAN).
 *                   Since the Linux default is to configure I/O BARs to the
 *                   bottom 4K, no special offset is needed. Just set to zero.
 *
 ****************************************************************************/
static struct pci_controller msp_pci_controller = {
        .pci_ops        = &msp_pci_ops,
        .mem_resource   = &pci_mem_resource,
        .mem_offset     = 0,
        .io_map_base    = MSP_PCI_IOSPACE_BASE,
        .io_resource    = &pci_io_resource,
        .io_offset      = 0
};

/*****************************************************************************
 *
 *  FUNCTION: msp_pci_init
 *  _________________________________________________________________________
 *
 *  DESCRIPTION: Initialize the PCI Host Controller and register it with
 *               Linux so Linux can seize control of the PCI bus.
 *
 ****************************************************************************/
void __init msp_pci_init(void)
{
        struct msp_pci_regs *preg = (void *)PCI_BASE_REG;
        u32 id;

        /* Extract Device ID */
        id = read_reg32(PCI_JTAG_DEVID_REG, 0xFFFF) >> 12;

        /* Check if JTAG ID identifies MSP7120 */
        if (!MSP_HAS_PCI(id)) {
                printk(KERN_WARNING "PCI: No PCI; id reads as %x\n", id);
                goto no_pci;
        }

        /*
         * Enable flushing of the PCI-SDRAM queue upon a read
         * of the SDRAM's Memory Configuration Register.
         */
        *(unsigned long *)QFLUSH_REG_1 = 3;

        /* Configure PCI Host Controller. */
        preg->if_status = ~0;           /* Clear cause register bits */
        preg->config_addr = 0;          /* Clear config access */
        preg->oatran    = MSP_PCI_OATRAN; /* PCI outbound addr translation */
        preg->if_mask   = 0xF8BF87C0;   /* Enable all PCI status interrupts */

        /* configure so inb(), outb(), and family are functional */
        set_io_port_base(MSP_PCI_IOSPACE_BASE);

        /* Tell Linux the details of the MSP7120 PCI Host Controller */
        register_pci_controller(&msp_pci_controller);

        return;

no_pci:
        /* Disable PCI channel */
        printk(KERN_WARNING "PCI: no host PCI bus detected\n");
}