Merge tag 'trace-v5.11-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt...

[linux/fpc-iii.git] / drivers / hwmon / lm80.c

// SPDX-License-Identifier: GPL-2.0-or-later
/*
 * lm80.c - From lm_sensors, Linux kernel modules for hardware
 *          monitoring
 * Copyright (C) 1998, 1999  Frodo Looijaard <frodol@dds.nl>
 *                           and Philip Edelbrock <phil@netroedge.com>
 *
 * Ported to Linux 2.6 by Tiago Sousa <mirage@kaotik.org>
 */

#include <linux/module.h>
#include <linux/init.h>
#include <linux/slab.h>
#include <linux/jiffies.h>
#include <linux/i2c.h>
#include <linux/hwmon.h>
#include <linux/hwmon-sysfs.h>
#include <linux/err.h>
#include <linux/mutex.h>

/* Addresses to scan */
static const unsigned short normal_i2c[] = { 0x28, 0x29, 0x2a, 0x2b, 0x2c, 0x2d,
                                                0x2e, 0x2f, I2C_CLIENT_END };

/* Many LM80 constants specified below */

/* The LM80 registers */
#define LM80_REG_IN_MAX(nr)             (0x2a + (nr) * 2)
#define LM80_REG_IN_MIN(nr)             (0x2b + (nr) * 2)
#define LM80_REG_IN(nr)                 (0x20 + (nr))

#define LM80_REG_FAN1                   0x28
#define LM80_REG_FAN2                   0x29
#define LM80_REG_FAN_MIN(nr)            (0x3b + (nr))

#define LM80_REG_TEMP                   0x27
#define LM80_REG_TEMP_HOT_MAX           0x38
#define LM80_REG_TEMP_HOT_HYST          0x39
#define LM80_REG_TEMP_OS_MAX            0x3a
#define LM80_REG_TEMP_OS_HYST           0x3b

#define LM80_REG_CONFIG                 0x00
#define LM80_REG_ALARM1                 0x01
#define LM80_REG_ALARM2                 0x02
#define LM80_REG_MASK1                  0x03
#define LM80_REG_MASK2                  0x04
#define LM80_REG_FANDIV                 0x05
#define LM80_REG_RES                    0x06

#define LM96080_REG_CONV_RATE           0x07
#define LM96080_REG_MAN_ID              0x3e
#define LM96080_REG_DEV_ID              0x3f


/*
 * Conversions. Rounding and limit checking is only done on the TO_REG
 * variants. Note that you should be a bit careful with which arguments
 * these macros are called: arguments may be evaluated more than once.
 * Fixing this is just not worth it.
 */

#define IN_TO_REG(val)          (clamp_val(((val) + 5) / 10, 0, 255))
#define IN_FROM_REG(val)        ((val) * 10)

static inline unsigned char FAN_TO_REG(unsigned rpm, unsigned div)
{
        if (rpm == 0)
                return 255;
        rpm = clamp_val(rpm, 1, 1000000);
        return clamp_val((1350000 + rpm * div / 2) / (rpm * div), 1, 254);
}

#define FAN_FROM_REG(val, div)  ((val) == 0 ? -1 : \
                                (val) == 255 ? 0 : 1350000/((div) * (val)))

#define TEMP_FROM_REG(reg)      ((reg) * 125 / 32)
#define TEMP_TO_REG(temp)       (DIV_ROUND_CLOSEST(clamp_val((temp), \
                                        -128000, 127000), 1000) << 8)

#define DIV_FROM_REG(val)               (1 << (val))

enum temp_index {
        t_input = 0,
        t_hot_max,
        t_hot_hyst,
        t_os_max,
        t_os_hyst,
        t_num_temp
};

static const u8 temp_regs[t_num_temp] = {
        [t_input] = LM80_REG_TEMP,
        [t_hot_max] = LM80_REG_TEMP_HOT_MAX,
        [t_hot_hyst] = LM80_REG_TEMP_HOT_HYST,
        [t_os_max] = LM80_REG_TEMP_OS_MAX,
        [t_os_hyst] = LM80_REG_TEMP_OS_HYST,
};

enum in_index {
        i_input = 0,
        i_max,
        i_min,
        i_num_in
};

enum fan_index {
        f_input,
        f_min,
        f_num_fan
};

/*
 * Client data (each client gets its own)
 */

struct lm80_data {
        struct i2c_client *client;
        struct mutex update_lock;
        char error;             /* !=0 if error occurred during last update */
        char valid;             /* !=0 if following fields are valid */
        unsigned long last_updated;     /* In jiffies */

        u8 in[i_num_in][7];     /* Register value, 1st index is enum in_index */
        u8 fan[f_num_fan][2];   /* Register value, 1st index enum fan_index */
        u8 fan_div[2];          /* Register encoding, shifted right */
        s16 temp[t_num_temp];   /* Register values, normalized to 16 bit */
        u16 alarms;             /* Register encoding, combined */
};

static int lm80_read_value(struct i2c_client *client, u8 reg)
{
        return i2c_smbus_read_byte_data(client, reg);
}

static int lm80_write_value(struct i2c_client *client, u8 reg, u8 value)
{
        return i2c_smbus_write_byte_data(client, reg, value);
}

/* Called when we have found a new LM80 and after read errors */
static void lm80_init_client(struct i2c_client *client)
{
        /*
         * Reset all except Watchdog values and last conversion values
         * This sets fan-divs to 2, among others. This makes most other
         * initializations unnecessary
         */
        lm80_write_value(client, LM80_REG_CONFIG, 0x80);
        /* Set 11-bit temperature resolution */
        lm80_write_value(client, LM80_REG_RES, 0x08);

        /* Start monitoring */
        lm80_write_value(client, LM80_REG_CONFIG, 0x01);
}

static struct lm80_data *lm80_update_device(struct device *dev)
{
        struct lm80_data *data = dev_get_drvdata(dev);
        struct i2c_client *client = data->client;
        int i;
        int rv;
        int prev_rv;
        struct lm80_data *ret = data;

        mutex_lock(&data->update_lock);

        if (data->error)
                lm80_init_client(client);

        if (time_after(jiffies, data->last_updated + 2 * HZ) || !data->valid) {
                dev_dbg(dev, "Starting lm80 update\n");
                for (i = 0; i <= 6; i++) {
                        rv = lm80_read_value(client, LM80_REG_IN(i));
                        if (rv < 0)
                                goto abort;
                        data->in[i_input][i] = rv;

                        rv = lm80_read_value(client, LM80_REG_IN_MIN(i));
                        if (rv < 0)
                                goto abort;
                        data->in[i_min][i] = rv;

                        rv = lm80_read_value(client, LM80_REG_IN_MAX(i));
                        if (rv < 0)
                                goto abort;
                        data->in[i_max][i] = rv;
                }

                rv = lm80_read_value(client, LM80_REG_FAN1);
                if (rv < 0)
                        goto abort;
                data->fan[f_input][0] = rv;

                rv = lm80_read_value(client, LM80_REG_FAN_MIN(1));
                if (rv < 0)
                        goto abort;
                data->fan[f_min][0] = rv;

                rv = lm80_read_value(client, LM80_REG_FAN2);
                if (rv < 0)
                        goto abort;
                data->fan[f_input][1] = rv;

                rv = lm80_read_value(client, LM80_REG_FAN_MIN(2));
                if (rv < 0)
                        goto abort;
                data->fan[f_min][1] = rv;

                prev_rv = rv = lm80_read_value(client, LM80_REG_TEMP);
                if (rv < 0)
                        goto abort;
                rv = lm80_read_value(client, LM80_REG_RES);
                if (rv < 0)
                        goto abort;
                data->temp[t_input] = (prev_rv << 8) | (rv & 0xf0);

                for (i = t_input + 1; i < t_num_temp; i++) {
                        rv = lm80_read_value(client, temp_regs[i]);
                        if (rv < 0)
                                goto abort;
                        data->temp[i] = rv << 8;
                }

                rv = lm80_read_value(client, LM80_REG_FANDIV);
                if (rv < 0)
                        goto abort;
                data->fan_div[0] = (rv >> 2) & 0x03;
                data->fan_div[1] = (rv >> 4) & 0x03;

                prev_rv = rv = lm80_read_value(client, LM80_REG_ALARM1);
                if (rv < 0)
                        goto abort;
                rv = lm80_read_value(client, LM80_REG_ALARM2);
                if (rv < 0)
                        goto abort;
                data->alarms = prev_rv + (rv << 8);

                data->last_updated = jiffies;
                data->valid = 1;
                data->error = 0;
        }
        goto done;

abort:
        ret = ERR_PTR(rv);
        data->valid = 0;
        data->error = 1;

done:
        mutex_unlock(&data->update_lock);

        return ret;
}

/*
 * Sysfs stuff
 */

static ssize_t in_show(struct device *dev, struct device_attribute *attr,
                       char *buf)
{
        struct lm80_data *data = lm80_update_device(dev);
        int index = to_sensor_dev_attr_2(attr)->index;
        int nr = to_sensor_dev_attr_2(attr)->nr;

        if (IS_ERR(data))
                return PTR_ERR(data);
        return sprintf(buf, "%d\n", IN_FROM_REG(data->in[nr][index]));
}

static ssize_t in_store(struct device *dev, struct device_attribute *attr,
                        const char *buf, size_t count)
{
        struct lm80_data *data = dev_get_drvdata(dev);
        struct i2c_client *client = data->client;
        int index = to_sensor_dev_attr_2(attr)->index;
        int nr = to_sensor_dev_attr_2(attr)->nr;
        long val;
        u8 reg;
        int err = kstrtol(buf, 10, &val);
        if (err < 0)
                return err;

        reg = nr == i_min ? LM80_REG_IN_MIN(index) : LM80_REG_IN_MAX(index);

        mutex_lock(&data->update_lock);
        data->in[nr][index] = IN_TO_REG(val);
        lm80_write_value(client, reg, data->in[nr][index]);
        mutex_unlock(&data->update_lock);
        return count;
}

static ssize_t fan_show(struct device *dev, struct device_attribute *attr,
                        char *buf)
{
        int index = to_sensor_dev_attr_2(attr)->index;
        int nr = to_sensor_dev_attr_2(attr)->nr;
        struct lm80_data *data = lm80_update_device(dev);
        if (IS_ERR(data))
                return PTR_ERR(data);
        return sprintf(buf, "%d\n", FAN_FROM_REG(data->fan[nr][index],
                       DIV_FROM_REG(data->fan_div[index])));
}

static ssize_t fan_div_show(struct device *dev, struct device_attribute *attr,
                            char *buf)
{
        int nr = to_sensor_dev_attr(attr)->index;
        struct lm80_data *data = lm80_update_device(dev);
        if (IS_ERR(data))
                return PTR_ERR(data);
        return sprintf(buf, "%d\n", DIV_FROM_REG(data->fan_div[nr]));
}

static ssize_t fan_store(struct device *dev, struct device_attribute *attr,
                         const char *buf, size_t count)
{
        int index = to_sensor_dev_attr_2(attr)->index;
        int nr = to_sensor_dev_attr_2(attr)->nr;
        struct lm80_data *data = dev_get_drvdata(dev);
        struct i2c_client *client = data->client;
        unsigned long val;
        int err = kstrtoul(buf, 10, &val);
        if (err < 0)
                return err;

        mutex_lock(&data->update_lock);
        data->fan[nr][index] = FAN_TO_REG(val,
                                          DIV_FROM_REG(data->fan_div[index]));
        lm80_write_value(client, LM80_REG_FAN_MIN(index + 1),
                         data->fan[nr][index]);
        mutex_unlock(&data->update_lock);
        return count;
}

/*
 * Note: we save and restore the fan minimum here, because its value is
 * determined in part by the fan divisor.  This follows the principle of
 * least surprise; the user doesn't expect the fan minimum to change just
 * because the divisor changed.
 */
static ssize_t fan_div_store(struct device *dev,
                             struct device_attribute *attr, const char *buf,
                             size_t count)
{
        int nr = to_sensor_dev_attr(attr)->index;
        struct lm80_data *data = dev_get_drvdata(dev);
        struct i2c_client *client = data->client;
        unsigned long min, val;
        u8 reg;
        int rv;

        rv = kstrtoul(buf, 10, &val);
        if (rv < 0)
                return rv;

        /* Save fan_min */
        mutex_lock(&data->update_lock);
        min = FAN_FROM_REG(data->fan[f_min][nr],
                           DIV_FROM_REG(data->fan_div[nr]));

        switch (val) {
        case 1:
                data->fan_div[nr] = 0;
                break;
        case 2:
                data->fan_div[nr] = 1;
                break;
        case 4:
                data->fan_div[nr] = 2;
                break;
        case 8:
                data->fan_div[nr] = 3;
                break;
        default:
                dev_err(dev,
                        "fan_div value %ld not supported. Choose one of 1, 2, 4 or 8!\n",
                        val);
                mutex_unlock(&data->update_lock);
                return -EINVAL;
        }

        rv = lm80_read_value(client, LM80_REG_FANDIV);
        if (rv < 0) {
                mutex_unlock(&data->update_lock);
                return rv;
        }
        reg = (rv & ~(3 << (2 * (nr + 1))))
            | (data->fan_div[nr] << (2 * (nr + 1)));
        lm80_write_value(client, LM80_REG_FANDIV, reg);

        /* Restore fan_min */
        data->fan[f_min][nr] = FAN_TO_REG(min, DIV_FROM_REG(data->fan_div[nr]));
        lm80_write_value(client, LM80_REG_FAN_MIN(nr + 1),
                         data->fan[f_min][nr]);
        mutex_unlock(&data->update_lock);

        return count;
}

static ssize_t temp_show(struct device *dev, struct device_attribute *devattr,
                         char *buf)
{
        struct sensor_device_attribute *attr = to_sensor_dev_attr(devattr);
        struct lm80_data *data = lm80_update_device(dev);
        if (IS_ERR(data))
                return PTR_ERR(data);
        return sprintf(buf, "%d\n", TEMP_FROM_REG(data->temp[attr->index]));
}

static ssize_t temp_store(struct device *dev,
                          struct device_attribute *devattr, const char *buf,
                          size_t count)
{
        struct sensor_device_attribute *attr = to_sensor_dev_attr(devattr);
        struct lm80_data *data = dev_get_drvdata(dev);
        struct i2c_client *client = data->client;
        int nr = attr->index;
        long val;
        int err = kstrtol(buf, 10, &val);
        if (err < 0)
                return err;

        mutex_lock(&data->update_lock);
        data->temp[nr] = TEMP_TO_REG(val);
        lm80_write_value(client, temp_regs[nr], data->temp[nr] >> 8);
        mutex_unlock(&data->update_lock);
        return count;
}

static ssize_t alarms_show(struct device *dev, struct device_attribute *attr,
                           char *buf)
{
        struct lm80_data *data = lm80_update_device(dev);
        if (IS_ERR(data))
                return PTR_ERR(data);
        return sprintf(buf, "%u\n", data->alarms);
}

static ssize_t alarm_show(struct device *dev, struct device_attribute *attr,
                          char *buf)
{
        int bitnr = to_sensor_dev_attr(attr)->index;
        struct lm80_data *data = lm80_update_device(dev);
        if (IS_ERR(data))
                return PTR_ERR(data);
        return sprintf(buf, "%u\n", (data->alarms >> bitnr) & 1);
}

static SENSOR_DEVICE_ATTR_2_RW(in0_min, in, i_min, 0);
static SENSOR_DEVICE_ATTR_2_RW(in1_min, in, i_min, 1);
static SENSOR_DEVICE_ATTR_2_RW(in2_min, in, i_min, 2);
static SENSOR_DEVICE_ATTR_2_RW(in3_min, in, i_min, 3);
static SENSOR_DEVICE_ATTR_2_RW(in4_min, in, i_min, 4);
static SENSOR_DEVICE_ATTR_2_RW(in5_min, in, i_min, 5);
static SENSOR_DEVICE_ATTR_2_RW(in6_min, in, i_min, 6);
static SENSOR_DEVICE_ATTR_2_RW(in0_max, in, i_max, 0);
static SENSOR_DEVICE_ATTR_2_RW(in1_max, in, i_max, 1);
static SENSOR_DEVICE_ATTR_2_RW(in2_max, in, i_max, 2);
static SENSOR_DEVICE_ATTR_2_RW(in3_max, in, i_max, 3);
static SENSOR_DEVICE_ATTR_2_RW(in4_max, in, i_max, 4);
static SENSOR_DEVICE_ATTR_2_RW(in5_max, in, i_max, 5);
static SENSOR_DEVICE_ATTR_2_RW(in6_max, in, i_max, 6);
static SENSOR_DEVICE_ATTR_2_RO(in0_input, in, i_input, 0);
static SENSOR_DEVICE_ATTR_2_RO(in1_input, in, i_input, 1);
static SENSOR_DEVICE_ATTR_2_RO(in2_input, in, i_input, 2);
static SENSOR_DEVICE_ATTR_2_RO(in3_input, in, i_input, 3);
static SENSOR_DEVICE_ATTR_2_RO(in4_input, in, i_input, 4);
static SENSOR_DEVICE_ATTR_2_RO(in5_input, in, i_input, 5);
static SENSOR_DEVICE_ATTR_2_RO(in6_input, in, i_input, 6);
static SENSOR_DEVICE_ATTR_2_RW(fan1_min, fan, f_min, 0);
static SENSOR_DEVICE_ATTR_2_RW(fan2_min, fan, f_min, 1);
static SENSOR_DEVICE_ATTR_2_RO(fan1_input, fan, f_input, 0);
static SENSOR_DEVICE_ATTR_2_RO(fan2_input, fan, f_input, 1);
static SENSOR_DEVICE_ATTR_RW(fan1_div, fan_div, 0);
static SENSOR_DEVICE_ATTR_RW(fan2_div, fan_div, 1);
static SENSOR_DEVICE_ATTR_RO(temp1_input, temp, t_input);
static SENSOR_DEVICE_ATTR_RW(temp1_max, temp, t_hot_max);
static SENSOR_DEVICE_ATTR_RW(temp1_max_hyst, temp, t_hot_hyst);
static SENSOR_DEVICE_ATTR_RW(temp1_crit, temp, t_os_max);
static SENSOR_DEVICE_ATTR_RW(temp1_crit_hyst, temp, t_os_hyst);
static DEVICE_ATTR_RO(alarms);
static SENSOR_DEVICE_ATTR_RO(in0_alarm, alarm, 0);
static SENSOR_DEVICE_ATTR_RO(in1_alarm, alarm, 1);
static SENSOR_DEVICE_ATTR_RO(in2_alarm, alarm, 2);
static SENSOR_DEVICE_ATTR_RO(in3_alarm, alarm, 3);
static SENSOR_DEVICE_ATTR_RO(in4_alarm, alarm, 4);
static SENSOR_DEVICE_ATTR_RO(in5_alarm, alarm, 5);
static SENSOR_DEVICE_ATTR_RO(in6_alarm, alarm, 6);
static SENSOR_DEVICE_ATTR_RO(fan1_alarm, alarm, 10);
static SENSOR_DEVICE_ATTR_RO(fan2_alarm, alarm, 11);
static SENSOR_DEVICE_ATTR_RO(temp1_max_alarm, alarm, 8);
static SENSOR_DEVICE_ATTR_RO(temp1_crit_alarm, alarm, 13);

/*
 * Real code
 */

static struct attribute *lm80_attrs[] = {
        &sensor_dev_attr_in0_min.dev_attr.attr,
        &sensor_dev_attr_in1_min.dev_attr.attr,
        &sensor_dev_attr_in2_min.dev_attr.attr,
        &sensor_dev_attr_in3_min.dev_attr.attr,
        &sensor_dev_attr_in4_min.dev_attr.attr,
        &sensor_dev_attr_in5_min.dev_attr.attr,
        &sensor_dev_attr_in6_min.dev_attr.attr,
        &sensor_dev_attr_in0_max.dev_attr.attr,
        &sensor_dev_attr_in1_max.dev_attr.attr,
        &sensor_dev_attr_in2_max.dev_attr.attr,
        &sensor_dev_attr_in3_max.dev_attr.attr,
        &sensor_dev_attr_in4_max.dev_attr.attr,
        &sensor_dev_attr_in5_max.dev_attr.attr,
        &sensor_dev_attr_in6_max.dev_attr.attr,
        &sensor_dev_attr_in0_input.dev_attr.attr,
        &sensor_dev_attr_in1_input.dev_attr.attr,
        &sensor_dev_attr_in2_input.dev_attr.attr,
        &sensor_dev_attr_in3_input.dev_attr.attr,
        &sensor_dev_attr_in4_input.dev_attr.attr,
        &sensor_dev_attr_in5_input.dev_attr.attr,
        &sensor_dev_attr_in6_input.dev_attr.attr,
        &sensor_dev_attr_fan1_min.dev_attr.attr,
        &sensor_dev_attr_fan2_min.dev_attr.attr,
        &sensor_dev_attr_fan1_input.dev_attr.attr,
        &sensor_dev_attr_fan2_input.dev_attr.attr,
        &sensor_dev_attr_fan1_div.dev_attr.attr,
        &sensor_dev_attr_fan2_div.dev_attr.attr,
        &sensor_dev_attr_temp1_input.dev_attr.attr,
        &sensor_dev_attr_temp1_max.dev_attr.attr,
        &sensor_dev_attr_temp1_max_hyst.dev_attr.attr,
        &sensor_dev_attr_temp1_crit.dev_attr.attr,
        &sensor_dev_attr_temp1_crit_hyst.dev_attr.attr,
        &dev_attr_alarms.attr,
        &sensor_dev_attr_in0_alarm.dev_attr.attr,
        &sensor_dev_attr_in1_alarm.dev_attr.attr,
        &sensor_dev_attr_in2_alarm.dev_attr.attr,
        &sensor_dev_attr_in3_alarm.dev_attr.attr,
        &sensor_dev_attr_in4_alarm.dev_attr.attr,
        &sensor_dev_attr_in5_alarm.dev_attr.attr,
        &sensor_dev_attr_in6_alarm.dev_attr.attr,
        &sensor_dev_attr_fan1_alarm.dev_attr.attr,
        &sensor_dev_attr_fan2_alarm.dev_attr.attr,
        &sensor_dev_attr_temp1_max_alarm.dev_attr.attr,
        &sensor_dev_attr_temp1_crit_alarm.dev_attr.attr,
        NULL
};
ATTRIBUTE_GROUPS(lm80);

/* Return 0 if detection is successful, -ENODEV otherwise */
static int lm80_detect(struct i2c_client *client, struct i2c_board_info *info)
{
        struct i2c_adapter *adapter = client->adapter;
        int i, cur, man_id, dev_id;
        const char *name = NULL;

        if (!i2c_check_functionality(adapter, I2C_FUNC_SMBUS_BYTE_DATA))
                return -ENODEV;

        /* First check for unused bits, common to both chip types */
        if ((lm80_read_value(client, LM80_REG_ALARM2) & 0xc0)
         || (lm80_read_value(client, LM80_REG_CONFIG) & 0x80))
                return -ENODEV;

        /*
         * The LM96080 has manufacturer and stepping/die rev registers so we
         * can just check that. The LM80 does not have such registers so we
         * have to use a more expensive trick.
         */
        man_id = lm80_read_value(client, LM96080_REG_MAN_ID);
        dev_id = lm80_read_value(client, LM96080_REG_DEV_ID);
        if (man_id == 0x01 && dev_id == 0x08) {
                /* Check more unused bits for confirmation */
                if (lm80_read_value(client, LM96080_REG_CONV_RATE) & 0xfe)
                        return -ENODEV;

                name = "lm96080";
        } else {
                /* Check 6-bit addressing */
                for (i = 0x2a; i <= 0x3d; i++) {
                        cur = i2c_smbus_read_byte_data(client, i);
                        if ((i2c_smbus_read_byte_data(client, i + 0x40) != cur)
                         || (i2c_smbus_read_byte_data(client, i + 0x80) != cur)
                         || (i2c_smbus_read_byte_data(client, i + 0xc0) != cur))
                                return -ENODEV;
                }

                name = "lm80";
        }

        strlcpy(info->type, name, I2C_NAME_SIZE);

        return 0;
}

static int lm80_probe(struct i2c_client *client)
{
        struct device *dev = &client->dev;
        struct device *hwmon_dev;
        struct lm80_data *data;
        int rv;

        data = devm_kzalloc(dev, sizeof(struct lm80_data), GFP_KERNEL);
        if (!data)
                return -ENOMEM;

        data->client = client;
        mutex_init(&data->update_lock);

        /* Initialize the LM80 chip */
        lm80_init_client(client);

        /* A few vars need to be filled upon startup */
        rv = lm80_read_value(client, LM80_REG_FAN_MIN(1));
        if (rv < 0)
                return rv;
        data->fan[f_min][0] = rv;
        rv = lm80_read_value(client, LM80_REG_FAN_MIN(2));
        if (rv < 0)
                return rv;
        data->fan[f_min][1] = rv;

        hwmon_dev = devm_hwmon_device_register_with_groups(dev, client->name,
                                                           data, lm80_groups);

        return PTR_ERR_OR_ZERO(hwmon_dev);
}

/*
 * Driver data (common to all clients)
 */

static const struct i2c_device_id lm80_id[] = {
        { "lm80", 0 },
        { "lm96080", 1 },
        { }
};
MODULE_DEVICE_TABLE(i2c, lm80_id);

static struct i2c_driver lm80_driver = {
        .class          = I2C_CLASS_HWMON,
        .driver = {
                .name   = "lm80",
        },
        .probe_new      = lm80_probe,
        .id_table       = lm80_id,
        .detect         = lm80_detect,
        .address_list   = normal_i2c,
};

module_i2c_driver(lm80_driver);

MODULE_AUTHOR("Frodo Looijaard <frodol@dds.nl> and "
        "Philip Edelbrock <phil@netroedge.com>");
MODULE_DESCRIPTION("LM80 driver");
MODULE_LICENSE("GPL");