1 // SPDX-License-Identifier: GPL-2.0-only
3 * TI TRF7970a RFID/NFC Transceiver Driver
5 * Copyright (C) 2013 Texas Instruments Incorporated - http://www.ti.com
7 * Author: Erick Macias <emacias@ti.com>
8 * Author: Felipe Balbi <balbi@ti.com>
9 * Author: Mark A. Greer <mgreer@animalcreek.com>
12 #include <linux/module.h>
13 #include <linux/device.h>
14 #include <linux/netdevice.h>
15 #include <linux/interrupt.h>
16 #include <linux/pm_runtime.h>
17 #include <linux/nfc.h>
18 #include <linux/skbuff.h>
19 #include <linux/delay.h>
20 #include <linux/gpio/consumer.h>
22 #include <linux/spi/spi.h>
23 #include <linux/regulator/consumer.h>
25 #include <net/nfc/nfc.h>
26 #include <net/nfc/digital.h>
28 /* There are 3 ways the host can communicate with the trf7970a:
29 * parallel mode, SPI with Slave Select (SS) mode, and SPI without
30 * SS mode. The driver only supports the two SPI modes.
32 * The trf7970a is very timing sensitive and the VIN, EN2, and EN
33 * pins must asserted in that order and with specific delays in between.
34 * The delays used in the driver were provided by TI and have been
35 * confirmed to work with this driver. There is a bug with the current
36 * version of the trf7970a that requires that EN2 remain low no matter
37 * what. If it goes high, it will generate an RF field even when in
38 * passive target mode. TI has indicated that the chip will work okay
39 * when EN2 is left low. The 'en2-rf-quirk' device tree property
40 * indicates that trf7970a currently being used has the erratum and
41 * that EN2 must be kept low.
43 * Timeouts are implemented using the delayed workqueue kernel facility.
44 * Timeouts are required so things don't hang when there is no response
45 * from the trf7970a (or tag). Using this mechanism creates a race with
46 * interrupts, however. That is, an interrupt and a timeout could occur
47 * closely enough together that one is blocked by the mutex while the other
48 * executes. When the timeout handler executes first and blocks the
49 * interrupt handler, it will eventually set the state to IDLE so the
50 * interrupt handler will check the state and exit with no harm done.
51 * When the interrupt handler executes first and blocks the timeout handler,
52 * the cancel_delayed_work() call will know that it didn't cancel the
53 * work item (i.e., timeout) and will return zero. That return code is
54 * used by the timer handler to indicate that it should ignore the timeout
57 * Aborting an active command isn't as simple as it seems because the only
58 * way to abort a command that's already been sent to the tag is so turn
59 * off power to the tag. If we do that, though, we'd have to go through
60 * the entire anticollision procedure again but the digital layer doesn't
61 * support that. So, if an abort is received before trf7970a_send_cmd()
62 * has sent the command to the tag, it simply returns -ECANCELED. If the
63 * command has already been sent to the tag, then the driver continues
64 * normally and recieves the response data (or error) but just before
65 * sending the data upstream, it frees the rx_skb and sends -ECANCELED
66 * upstream instead. If the command failed, that error will be sent
69 * When recieving data from a tag and the interrupt status register has
70 * only the SRX bit set, it means that all of the data has been received
71 * (once what's in the fifo has been read). However, depending on timing
72 * an interrupt status with only the SRX bit set may not be recived. In
73 * those cases, the timeout mechanism is used to wait 20 ms in case more
74 * data arrives. After 20 ms, it is assumed that all of the data has been
75 * received and the accumulated rx data is sent upstream. The
76 * 'TRF7970A_ST_WAIT_FOR_RX_DATA_CONT' state is used for this purpose
77 * (i.e., it indicates that some data has been received but we're not sure
78 * if there is more coming so a timeout in this state means all data has
79 * been received and there isn't an error). The delay is 20 ms since delays
80 * of ~16 ms have been observed during testing.
82 * When transmitting a frame larger than the FIFO size (127 bytes), the
83 * driver will wait 20 ms for the FIFO to drain past the low-watermark
84 * and generate an interrupt. The low-watermark set to 32 bytes so the
85 * interrupt should fire after 127 - 32 = 95 bytes have been sent. At
86 * the lowest possible bit rate (6.62 kbps for 15693), it will take up
87 * to ~14.35 ms so 20 ms is used for the timeout.
89 * Type 2 write and sector select commands respond with a 4-bit ACK or NACK.
90 * Having only 4 bits in the FIFO won't normally generate an interrupt so
91 * driver enables the '4_bit_RX' bit of the Special Functions register 1
92 * to cause an interrupt in that case. Leaving that bit for a read command
93 * messes up the data returned so it is only enabled when the framing is
94 * 'NFC_DIGITAL_FRAMING_NFCA_T2T' and the command is not a read command.
95 * Unfortunately, that means that the driver has to peek into tx frames
96 * when the framing is 'NFC_DIGITAL_FRAMING_NFCA_T2T'. This is done by
97 * the trf7970a_per_cmd_config() routine.
99 * ISO/IEC 15693 frames specify whether to use single or double sub-carrier
100 * frequencies and whether to use low or high data rates in the flags byte
101 * of the frame. This means that the driver has to peek at all 15693 frames
102 * to determine what speed to set the communication to. In addition, write
103 * and lock commands use the OPTION flag to indicate that an EOF must be
104 * sent to the tag before it will send its response. So the driver has to
105 * examine all frames for that reason too.
107 * It is unclear how long to wait before sending the EOF. According to the
108 * Note under Table 1-1 in section 1.6 of
109 * http://www.ti.com/lit/ug/scbu011/scbu011.pdf, that wait should be at least
110 * 10 ms for TI Tag-it HF-I tags; however testing has shown that is not long
111 * enough so 20 ms is used. So the timer is set to 40 ms - 20 ms to drain
112 * up to 127 bytes in the FIFO at the lowest bit rate plus another 20 ms to
113 * ensure the wait is long enough before sending the EOF. This seems to work
117 #define TRF7970A_SUPPORTED_PROTOCOLS \
118 (NFC_PROTO_MIFARE_MASK | NFC_PROTO_ISO14443_MASK | \
119 NFC_PROTO_ISO14443_B_MASK | NFC_PROTO_FELICA_MASK | \
120 NFC_PROTO_ISO15693_MASK | NFC_PROTO_NFC_DEP_MASK)
122 #define TRF7970A_AUTOSUSPEND_DELAY 30000 /* 30 seconds */
123 #define TRF7970A_13MHZ_CLOCK_FREQUENCY 13560000
124 #define TRF7970A_27MHZ_CLOCK_FREQUENCY 27120000
126 #define TRF7970A_RX_SKB_ALLOC_SIZE 256
128 #define TRF7970A_FIFO_SIZE 127
130 /* TX length is 3 nibbles long ==> 4KB - 1 bytes max */
131 #define TRF7970A_TX_MAX (4096 - 1)
133 #define TRF7970A_WAIT_FOR_TX_IRQ 20
134 #define TRF7970A_WAIT_FOR_RX_DATA_TIMEOUT 20
135 #define TRF7970A_WAIT_FOR_FIFO_DRAIN_TIMEOUT 20
136 #define TRF7970A_WAIT_TO_ISSUE_ISO15693_EOF 40
138 /* Guard times for various RF technologies (in us) */
139 #define TRF7970A_GUARD_TIME_NFCA 5000
140 #define TRF7970A_GUARD_TIME_NFCB 5000
141 #define TRF7970A_GUARD_TIME_NFCF 20000
142 #define TRF7970A_GUARD_TIME_15693 1000
145 /* Erratum: When reading IRQ Status register on trf7970a, we must issue a
146 * read continuous command for IRQ Status and Collision Position registers.
148 #define TRF7970A_QUIRK_IRQ_STATUS_READ BIT(0)
149 #define TRF7970A_QUIRK_EN2_MUST_STAY_LOW BIT(1)
151 /* Direct commands */
152 #define TRF7970A_CMD_IDLE 0x00
153 #define TRF7970A_CMD_SOFT_INIT 0x03
154 #define TRF7970A_CMD_RF_COLLISION 0x04
155 #define TRF7970A_CMD_RF_COLLISION_RESPONSE_N 0x05
156 #define TRF7970A_CMD_RF_COLLISION_RESPONSE_0 0x06
157 #define TRF7970A_CMD_FIFO_RESET 0x0f
158 #define TRF7970A_CMD_TRANSMIT_NO_CRC 0x10
159 #define TRF7970A_CMD_TRANSMIT 0x11
160 #define TRF7970A_CMD_DELAY_TRANSMIT_NO_CRC 0x12
161 #define TRF7970A_CMD_DELAY_TRANSMIT 0x13
162 #define TRF7970A_CMD_EOF 0x14
163 #define TRF7970A_CMD_CLOSE_SLOT 0x15
164 #define TRF7970A_CMD_BLOCK_RX 0x16
165 #define TRF7970A_CMD_ENABLE_RX 0x17
166 #define TRF7970A_CMD_TEST_INT_RF 0x18
167 #define TRF7970A_CMD_TEST_EXT_RF 0x19
168 #define TRF7970A_CMD_RX_GAIN_ADJUST 0x1a
170 /* Bits determining whether its a direct command or register R/W,
171 * whether to use a continuous SPI transaction or not, and the actual
172 * direct cmd opcode or regster address.
174 #define TRF7970A_CMD_BIT_CTRL BIT(7)
175 #define TRF7970A_CMD_BIT_RW BIT(6)
176 #define TRF7970A_CMD_BIT_CONTINUOUS BIT(5)
177 #define TRF7970A_CMD_BIT_OPCODE(opcode) ((opcode) & 0x1f)
179 /* Registers addresses */
180 #define TRF7970A_CHIP_STATUS_CTRL 0x00
181 #define TRF7970A_ISO_CTRL 0x01
182 #define TRF7970A_ISO14443B_TX_OPTIONS 0x02
183 #define TRF7970A_ISO14443A_HIGH_BITRATE_OPTIONS 0x03
184 #define TRF7970A_TX_TIMER_SETTING_H_BYTE 0x04
185 #define TRF7970A_TX_TIMER_SETTING_L_BYTE 0x05
186 #define TRF7970A_TX_PULSE_LENGTH_CTRL 0x06
187 #define TRF7970A_RX_NO_RESPONSE_WAIT 0x07
188 #define TRF7970A_RX_WAIT_TIME 0x08
189 #define TRF7970A_MODULATOR_SYS_CLK_CTRL 0x09
190 #define TRF7970A_RX_SPECIAL_SETTINGS 0x0a
191 #define TRF7970A_REG_IO_CTRL 0x0b
192 #define TRF7970A_IRQ_STATUS 0x0c
193 #define TRF7970A_COLLISION_IRQ_MASK 0x0d
194 #define TRF7970A_COLLISION_POSITION 0x0e
195 #define TRF7970A_RSSI_OSC_STATUS 0x0f
196 #define TRF7970A_SPECIAL_FCN_REG1 0x10
197 #define TRF7970A_SPECIAL_FCN_REG2 0x11
198 #define TRF7970A_RAM1 0x12
199 #define TRF7970A_RAM2 0x13
200 #define TRF7970A_ADJUTABLE_FIFO_IRQ_LEVELS 0x14
201 #define TRF7970A_NFC_LOW_FIELD_LEVEL 0x16
202 #define TRF7970A_NFCID1 0x17
203 #define TRF7970A_NFC_TARGET_LEVEL 0x18
204 #define TRF79070A_NFC_TARGET_PROTOCOL 0x19
205 #define TRF7970A_TEST_REGISTER1 0x1a
206 #define TRF7970A_TEST_REGISTER2 0x1b
207 #define TRF7970A_FIFO_STATUS 0x1c
208 #define TRF7970A_TX_LENGTH_BYTE1 0x1d
209 #define TRF7970A_TX_LENGTH_BYTE2 0x1e
210 #define TRF7970A_FIFO_IO_REGISTER 0x1f
212 /* Chip Status Control Register Bits */
213 #define TRF7970A_CHIP_STATUS_VRS5_3 BIT(0)
214 #define TRF7970A_CHIP_STATUS_REC_ON BIT(1)
215 #define TRF7970A_CHIP_STATUS_AGC_ON BIT(2)
216 #define TRF7970A_CHIP_STATUS_PM_ON BIT(3)
217 #define TRF7970A_CHIP_STATUS_RF_PWR BIT(4)
218 #define TRF7970A_CHIP_STATUS_RF_ON BIT(5)
219 #define TRF7970A_CHIP_STATUS_DIRECT BIT(6)
220 #define TRF7970A_CHIP_STATUS_STBY BIT(7)
222 /* ISO Control Register Bits */
223 #define TRF7970A_ISO_CTRL_15693_SGL_1OF4_662 0x00
224 #define TRF7970A_ISO_CTRL_15693_SGL_1OF256_662 0x01
225 #define TRF7970A_ISO_CTRL_15693_SGL_1OF4_2648 0x02
226 #define TRF7970A_ISO_CTRL_15693_SGL_1OF256_2648 0x03
227 #define TRF7970A_ISO_CTRL_15693_DBL_1OF4_667a 0x04
228 #define TRF7970A_ISO_CTRL_15693_DBL_1OF256_667 0x05
229 #define TRF7970A_ISO_CTRL_15693_DBL_1OF4_2669 0x06
230 #define TRF7970A_ISO_CTRL_15693_DBL_1OF256_2669 0x07
231 #define TRF7970A_ISO_CTRL_14443A_106 0x08
232 #define TRF7970A_ISO_CTRL_14443A_212 0x09
233 #define TRF7970A_ISO_CTRL_14443A_424 0x0a
234 #define TRF7970A_ISO_CTRL_14443A_848 0x0b
235 #define TRF7970A_ISO_CTRL_14443B_106 0x0c
236 #define TRF7970A_ISO_CTRL_14443B_212 0x0d
237 #define TRF7970A_ISO_CTRL_14443B_424 0x0e
238 #define TRF7970A_ISO_CTRL_14443B_848 0x0f
239 #define TRF7970A_ISO_CTRL_FELICA_212 0x1a
240 #define TRF7970A_ISO_CTRL_FELICA_424 0x1b
241 #define TRF7970A_ISO_CTRL_NFC_NFCA_106 0x01
242 #define TRF7970A_ISO_CTRL_NFC_NFCF_212 0x02
243 #define TRF7970A_ISO_CTRL_NFC_NFCF_424 0x03
244 #define TRF7970A_ISO_CTRL_NFC_CE_14443A 0x00
245 #define TRF7970A_ISO_CTRL_NFC_CE_14443B 0x01
246 #define TRF7970A_ISO_CTRL_NFC_CE BIT(2)
247 #define TRF7970A_ISO_CTRL_NFC_ACTIVE BIT(3)
248 #define TRF7970A_ISO_CTRL_NFC_INITIATOR BIT(4)
249 #define TRF7970A_ISO_CTRL_NFC_NFC_CE_MODE BIT(5)
250 #define TRF7970A_ISO_CTRL_RFID BIT(5)
251 #define TRF7970A_ISO_CTRL_DIR_MODE BIT(6)
252 #define TRF7970A_ISO_CTRL_RX_CRC_N BIT(7) /* true == No CRC */
254 #define TRF7970A_ISO_CTRL_RFID_SPEED_MASK 0x1f
256 /* Modulator and SYS_CLK Control Register Bits */
257 #define TRF7970A_MODULATOR_DEPTH(n) ((n) & 0x7)
258 #define TRF7970A_MODULATOR_DEPTH_ASK10 (TRF7970A_MODULATOR_DEPTH(0))
259 #define TRF7970A_MODULATOR_DEPTH_OOK (TRF7970A_MODULATOR_DEPTH(1))
260 #define TRF7970A_MODULATOR_DEPTH_ASK7 (TRF7970A_MODULATOR_DEPTH(2))
261 #define TRF7970A_MODULATOR_DEPTH_ASK8_5 (TRF7970A_MODULATOR_DEPTH(3))
262 #define TRF7970A_MODULATOR_DEPTH_ASK13 (TRF7970A_MODULATOR_DEPTH(4))
263 #define TRF7970A_MODULATOR_DEPTH_ASK16 (TRF7970A_MODULATOR_DEPTH(5))
264 #define TRF7970A_MODULATOR_DEPTH_ASK22 (TRF7970A_MODULATOR_DEPTH(6))
265 #define TRF7970A_MODULATOR_DEPTH_ASK30 (TRF7970A_MODULATOR_DEPTH(7))
266 #define TRF7970A_MODULATOR_EN_ANA BIT(3)
267 #define TRF7970A_MODULATOR_CLK(n) (((n) & 0x3) << 4)
268 #define TRF7970A_MODULATOR_CLK_DISABLED (TRF7970A_MODULATOR_CLK(0))
269 #define TRF7970A_MODULATOR_CLK_3_6 (TRF7970A_MODULATOR_CLK(1))
270 #define TRF7970A_MODULATOR_CLK_6_13 (TRF7970A_MODULATOR_CLK(2))
271 #define TRF7970A_MODULATOR_CLK_13_27 (TRF7970A_MODULATOR_CLK(3))
272 #define TRF7970A_MODULATOR_EN_OOK BIT(6)
273 #define TRF7970A_MODULATOR_27MHZ BIT(7)
275 #define TRF7970A_RX_SPECIAL_SETTINGS_NO_LIM BIT(0)
276 #define TRF7970A_RX_SPECIAL_SETTINGS_AGCR BIT(1)
277 #define TRF7970A_RX_SPECIAL_SETTINGS_GD_0DB (0x0 << 2)
278 #define TRF7970A_RX_SPECIAL_SETTINGS_GD_5DB (0x1 << 2)
279 #define TRF7970A_RX_SPECIAL_SETTINGS_GD_10DB (0x2 << 2)
280 #define TRF7970A_RX_SPECIAL_SETTINGS_GD_15DB (0x3 << 2)
281 #define TRF7970A_RX_SPECIAL_SETTINGS_HBT BIT(4)
282 #define TRF7970A_RX_SPECIAL_SETTINGS_M848 BIT(5)
283 #define TRF7970A_RX_SPECIAL_SETTINGS_C424 BIT(6)
284 #define TRF7970A_RX_SPECIAL_SETTINGS_C212 BIT(7)
286 #define TRF7970A_REG_IO_CTRL_VRS(v) ((v) & 0x07)
287 #define TRF7970A_REG_IO_CTRL_IO_LOW BIT(5)
288 #define TRF7970A_REG_IO_CTRL_EN_EXT_PA BIT(6)
289 #define TRF7970A_REG_IO_CTRL_AUTO_REG BIT(7)
291 /* IRQ Status Register Bits */
292 #define TRF7970A_IRQ_STATUS_NORESP BIT(0) /* ISO15693 only */
293 #define TRF7970A_IRQ_STATUS_NFC_COL_ERROR BIT(0)
294 #define TRF7970A_IRQ_STATUS_COL BIT(1)
295 #define TRF7970A_IRQ_STATUS_FRAMING_EOF_ERROR BIT(2)
296 #define TRF7970A_IRQ_STATUS_NFC_RF BIT(2)
297 #define TRF7970A_IRQ_STATUS_PARITY_ERROR BIT(3)
298 #define TRF7970A_IRQ_STATUS_NFC_SDD BIT(3)
299 #define TRF7970A_IRQ_STATUS_CRC_ERROR BIT(4)
300 #define TRF7970A_IRQ_STATUS_NFC_PROTO_ERROR BIT(4)
301 #define TRF7970A_IRQ_STATUS_FIFO BIT(5)
302 #define TRF7970A_IRQ_STATUS_SRX BIT(6)
303 #define TRF7970A_IRQ_STATUS_TX BIT(7)
305 #define TRF7970A_IRQ_STATUS_ERROR \
306 (TRF7970A_IRQ_STATUS_COL | \
307 TRF7970A_IRQ_STATUS_FRAMING_EOF_ERROR | \
308 TRF7970A_IRQ_STATUS_PARITY_ERROR | \
309 TRF7970A_IRQ_STATUS_CRC_ERROR)
311 #define TRF7970A_RSSI_OSC_STATUS_RSSI_MASK (BIT(2) | BIT(1) | BIT(0))
312 #define TRF7970A_RSSI_OSC_STATUS_RSSI_X_MASK (BIT(5) | BIT(4) | BIT(3))
313 #define TRF7970A_RSSI_OSC_STATUS_RSSI_OSC_OK BIT(6)
315 #define TRF7970A_SPECIAL_FCN_REG1_COL_7_6 BIT(0)
316 #define TRF7970A_SPECIAL_FCN_REG1_14_ANTICOLL BIT(1)
317 #define TRF7970A_SPECIAL_FCN_REG1_4_BIT_RX BIT(2)
318 #define TRF7970A_SPECIAL_FCN_REG1_SP_DIR_MODE BIT(3)
319 #define TRF7970A_SPECIAL_FCN_REG1_NEXT_SLOT_37US BIT(4)
320 #define TRF7970A_SPECIAL_FCN_REG1_PAR43 BIT(5)
322 #define TRF7970A_ADJUTABLE_FIFO_IRQ_LEVELS_WLH_124 (0x0 << 2)
323 #define TRF7970A_ADJUTABLE_FIFO_IRQ_LEVELS_WLH_120 (0x1 << 2)
324 #define TRF7970A_ADJUTABLE_FIFO_IRQ_LEVELS_WLH_112 (0x2 << 2)
325 #define TRF7970A_ADJUTABLE_FIFO_IRQ_LEVELS_WLH_96 (0x3 << 2)
326 #define TRF7970A_ADJUTABLE_FIFO_IRQ_LEVELS_WLL_4 0x0
327 #define TRF7970A_ADJUTABLE_FIFO_IRQ_LEVELS_WLL_8 0x1
328 #define TRF7970A_ADJUTABLE_FIFO_IRQ_LEVELS_WLL_16 0x2
329 #define TRF7970A_ADJUTABLE_FIFO_IRQ_LEVELS_WLL_32 0x3
331 #define TRF7970A_NFC_LOW_FIELD_LEVEL_RFDET(v) ((v) & 0x07)
332 #define TRF7970A_NFC_LOW_FIELD_LEVEL_CLEX_DIS BIT(7)
334 #define TRF7970A_NFC_TARGET_LEVEL_RFDET(v) ((v) & 0x07)
335 #define TRF7970A_NFC_TARGET_LEVEL_HI_RF BIT(3)
336 #define TRF7970A_NFC_TARGET_LEVEL_SDD_EN BIT(5)
337 #define TRF7970A_NFC_TARGET_LEVEL_LD_S_4BYTES (0x0 << 6)
338 #define TRF7970A_NFC_TARGET_LEVEL_LD_S_7BYTES (0x1 << 6)
339 #define TRF7970A_NFC_TARGET_LEVEL_LD_S_10BYTES (0x2 << 6)
341 #define TRF79070A_NFC_TARGET_PROTOCOL_NFCBR_106 BIT(0)
342 #define TRF79070A_NFC_TARGET_PROTOCOL_NFCBR_212 BIT(1)
343 #define TRF79070A_NFC_TARGET_PROTOCOL_NFCBR_424 (BIT(0) | BIT(1))
344 #define TRF79070A_NFC_TARGET_PROTOCOL_PAS_14443B BIT(2)
345 #define TRF79070A_NFC_TARGET_PROTOCOL_PAS_106 BIT(3)
346 #define TRF79070A_NFC_TARGET_PROTOCOL_FELICA BIT(4)
347 #define TRF79070A_NFC_TARGET_PROTOCOL_RF_L BIT(6)
348 #define TRF79070A_NFC_TARGET_PROTOCOL_RF_H BIT(7)
350 #define TRF79070A_NFC_TARGET_PROTOCOL_106A \
351 (TRF79070A_NFC_TARGET_PROTOCOL_RF_H | \
352 TRF79070A_NFC_TARGET_PROTOCOL_RF_L | \
353 TRF79070A_NFC_TARGET_PROTOCOL_PAS_106 | \
354 TRF79070A_NFC_TARGET_PROTOCOL_NFCBR_106)
356 #define TRF79070A_NFC_TARGET_PROTOCOL_106B \
357 (TRF79070A_NFC_TARGET_PROTOCOL_RF_H | \
358 TRF79070A_NFC_TARGET_PROTOCOL_RF_L | \
359 TRF79070A_NFC_TARGET_PROTOCOL_PAS_14443B | \
360 TRF79070A_NFC_TARGET_PROTOCOL_NFCBR_106)
362 #define TRF79070A_NFC_TARGET_PROTOCOL_212F \
363 (TRF79070A_NFC_TARGET_PROTOCOL_RF_H | \
364 TRF79070A_NFC_TARGET_PROTOCOL_RF_L | \
365 TRF79070A_NFC_TARGET_PROTOCOL_FELICA | \
366 TRF79070A_NFC_TARGET_PROTOCOL_NFCBR_212)
368 #define TRF79070A_NFC_TARGET_PROTOCOL_424F \
369 (TRF79070A_NFC_TARGET_PROTOCOL_RF_H | \
370 TRF79070A_NFC_TARGET_PROTOCOL_RF_L | \
371 TRF79070A_NFC_TARGET_PROTOCOL_FELICA | \
372 TRF79070A_NFC_TARGET_PROTOCOL_NFCBR_424)
374 #define TRF7970A_FIFO_STATUS_OVERFLOW BIT(7)
376 /* NFC (ISO/IEC 14443A) Type 2 Tag commands */
377 #define NFC_T2T_CMD_READ 0x30
379 /* ISO 15693 commands codes */
380 #define ISO15693_CMD_INVENTORY 0x01
381 #define ISO15693_CMD_READ_SINGLE_BLOCK 0x20
382 #define ISO15693_CMD_WRITE_SINGLE_BLOCK 0x21
383 #define ISO15693_CMD_LOCK_BLOCK 0x22
384 #define ISO15693_CMD_READ_MULTIPLE_BLOCK 0x23
385 #define ISO15693_CMD_WRITE_MULTIPLE_BLOCK 0x24
386 #define ISO15693_CMD_SELECT 0x25
387 #define ISO15693_CMD_RESET_TO_READY 0x26
388 #define ISO15693_CMD_WRITE_AFI 0x27
389 #define ISO15693_CMD_LOCK_AFI 0x28
390 #define ISO15693_CMD_WRITE_DSFID 0x29
391 #define ISO15693_CMD_LOCK_DSFID 0x2a
392 #define ISO15693_CMD_GET_SYSTEM_INFO 0x2b
393 #define ISO15693_CMD_GET_MULTIPLE_BLOCK_SECURITY_STATUS 0x2c
395 /* ISO 15693 request and response flags */
396 #define ISO15693_REQ_FLAG_SUB_CARRIER BIT(0)
397 #define ISO15693_REQ_FLAG_DATA_RATE BIT(1)
398 #define ISO15693_REQ_FLAG_INVENTORY BIT(2)
399 #define ISO15693_REQ_FLAG_PROTOCOL_EXT BIT(3)
400 #define ISO15693_REQ_FLAG_SELECT BIT(4)
401 #define ISO15693_REQ_FLAG_AFI BIT(4)
402 #define ISO15693_REQ_FLAG_ADDRESS BIT(5)
403 #define ISO15693_REQ_FLAG_NB_SLOTS BIT(5)
404 #define ISO15693_REQ_FLAG_OPTION BIT(6)
406 #define ISO15693_REQ_FLAG_SPEED_MASK \
407 (ISO15693_REQ_FLAG_SUB_CARRIER | ISO15693_REQ_FLAG_DATA_RATE)
409 enum trf7970a_state
{
413 TRF7970A_ST_IDLE_RX_BLOCKED
,
414 TRF7970A_ST_WAIT_FOR_TX_FIFO
,
415 TRF7970A_ST_WAIT_FOR_RX_DATA
,
416 TRF7970A_ST_WAIT_FOR_RX_DATA_CONT
,
417 TRF7970A_ST_WAIT_TO_ISSUE_EOF
,
418 TRF7970A_ST_LISTENING
,
419 TRF7970A_ST_LISTENING_MD
,
424 enum trf7970a_state state
;
426 struct spi_device
*spi
;
427 struct regulator
*regulator
;
428 struct nfc_digital_dev
*ddev
;
432 struct sk_buff
*tx_skb
;
433 struct sk_buff
*rx_skb
;
434 nfc_digital_cmd_complete_t cb
;
439 u8 modulator_sys_clk_ctrl
;
442 unsigned int guard_time
;
448 struct gpio_desc
*en_gpiod
;
449 struct gpio_desc
*en2_gpiod
;
451 unsigned int timeout
;
453 struct delayed_work timeout_work
;
456 static int trf7970a_cmd(struct trf7970a
*trf
, u8 opcode
)
458 u8 cmd
= TRF7970A_CMD_BIT_CTRL
| TRF7970A_CMD_BIT_OPCODE(opcode
);
461 dev_dbg(trf
->dev
, "cmd: 0x%x\n", cmd
);
463 ret
= spi_write(trf
->spi
, &cmd
, 1);
465 dev_err(trf
->dev
, "%s - cmd: 0x%x, ret: %d\n", __func__
, cmd
,
470 static int trf7970a_read(struct trf7970a
*trf
, u8 reg
, u8
*val
)
472 u8 addr
= TRF7970A_CMD_BIT_RW
| reg
;
475 ret
= spi_write_then_read(trf
->spi
, &addr
, 1, val
, 1);
477 dev_err(trf
->dev
, "%s - addr: 0x%x, ret: %d\n", __func__
, addr
,
480 dev_dbg(trf
->dev
, "read(0x%x): 0x%x\n", addr
, *val
);
485 static int trf7970a_read_cont(struct trf7970a
*trf
, u8 reg
, u8
*buf
,
488 u8 addr
= reg
| TRF7970A_CMD_BIT_RW
| TRF7970A_CMD_BIT_CONTINUOUS
;
489 struct spi_transfer t
[2];
490 struct spi_message m
;
493 dev_dbg(trf
->dev
, "read_cont(0x%x, %zd)\n", addr
, len
);
495 spi_message_init(&m
);
497 memset(&t
, 0, sizeof(t
));
500 t
[0].len
= sizeof(addr
);
501 spi_message_add_tail(&t
[0], &m
);
505 spi_message_add_tail(&t
[1], &m
);
507 ret
= spi_sync(trf
->spi
, &m
);
509 dev_err(trf
->dev
, "%s - addr: 0x%x, ret: %d\n", __func__
, addr
,
514 static int trf7970a_write(struct trf7970a
*trf
, u8 reg
, u8 val
)
516 u8 buf
[2] = { reg
, val
};
519 dev_dbg(trf
->dev
, "write(0x%x): 0x%x\n", reg
, val
);
521 ret
= spi_write(trf
->spi
, buf
, 2);
523 dev_err(trf
->dev
, "%s - write: 0x%x 0x%x, ret: %d\n", __func__
,
524 buf
[0], buf
[1], ret
);
529 static int trf7970a_read_irqstatus(struct trf7970a
*trf
, u8
*status
)
535 addr
= TRF7970A_IRQ_STATUS
| TRF7970A_CMD_BIT_RW
;
537 if (trf
->quirks
& TRF7970A_QUIRK_IRQ_STATUS_READ
) {
538 addr
|= TRF7970A_CMD_BIT_CONTINUOUS
;
539 ret
= spi_write_then_read(trf
->spi
, &addr
, 1, buf
, 2);
541 ret
= spi_write_then_read(trf
->spi
, &addr
, 1, buf
, 1);
545 dev_err(trf
->dev
, "%s - irqstatus: Status read failed: %d\n",
553 static int trf7970a_read_target_proto(struct trf7970a
*trf
, u8
*target_proto
)
559 addr
= TRF79070A_NFC_TARGET_PROTOCOL
| TRF7970A_CMD_BIT_RW
|
560 TRF7970A_CMD_BIT_CONTINUOUS
;
562 ret
= spi_write_then_read(trf
->spi
, &addr
, 1, buf
, 2);
564 dev_err(trf
->dev
, "%s - target_proto: Read failed: %d\n",
567 *target_proto
= buf
[0];
572 static int trf7970a_mode_detect(struct trf7970a
*trf
, u8
*rf_tech
)
575 u8 target_proto
, tech
;
577 ret
= trf7970a_read_target_proto(trf
, &target_proto
);
581 switch (target_proto
) {
582 case TRF79070A_NFC_TARGET_PROTOCOL_106A
:
583 tech
= NFC_DIGITAL_RF_TECH_106A
;
585 case TRF79070A_NFC_TARGET_PROTOCOL_106B
:
586 tech
= NFC_DIGITAL_RF_TECH_106B
;
588 case TRF79070A_NFC_TARGET_PROTOCOL_212F
:
589 tech
= NFC_DIGITAL_RF_TECH_212F
;
591 case TRF79070A_NFC_TARGET_PROTOCOL_424F
:
592 tech
= NFC_DIGITAL_RF_TECH_424F
;
595 dev_dbg(trf
->dev
, "%s - mode_detect: target_proto: 0x%x\n",
596 __func__
, target_proto
);
605 static void trf7970a_send_upstream(struct trf7970a
*trf
)
607 dev_kfree_skb_any(trf
->tx_skb
);
610 if (trf
->rx_skb
&& !IS_ERR(trf
->rx_skb
) && !trf
->aborting
)
611 print_hex_dump_debug("trf7970a rx data: ", DUMP_PREFIX_NONE
,
612 16, 1, trf
->rx_skb
->data
, trf
->rx_skb
->len
,
615 trf
->state
= TRF7970A_ST_IDLE
;
618 dev_dbg(trf
->dev
, "Abort process complete\n");
620 if (!IS_ERR(trf
->rx_skb
)) {
621 kfree_skb(trf
->rx_skb
);
622 trf
->rx_skb
= ERR_PTR(-ECANCELED
);
625 trf
->aborting
= false;
628 trf
->cb(trf
->ddev
, trf
->cb_arg
, trf
->rx_skb
);
633 static void trf7970a_send_err_upstream(struct trf7970a
*trf
, int errno
)
635 dev_dbg(trf
->dev
, "Error - state: %d, errno: %d\n", trf
->state
, errno
);
637 cancel_delayed_work(&trf
->timeout_work
);
639 kfree_skb(trf
->rx_skb
);
640 trf
->rx_skb
= ERR_PTR(errno
);
642 trf7970a_send_upstream(trf
);
645 static int trf7970a_transmit(struct trf7970a
*trf
, struct sk_buff
*skb
,
646 unsigned int len
, u8
*prefix
,
647 unsigned int prefix_len
)
649 struct spi_transfer t
[2];
650 struct spi_message m
;
651 unsigned int timeout
;
654 print_hex_dump_debug("trf7970a tx data: ", DUMP_PREFIX_NONE
,
655 16, 1, skb
->data
, len
, false);
657 spi_message_init(&m
);
659 memset(&t
, 0, sizeof(t
));
661 t
[0].tx_buf
= prefix
;
662 t
[0].len
= prefix_len
;
663 spi_message_add_tail(&t
[0], &m
);
665 t
[1].tx_buf
= skb
->data
;
667 spi_message_add_tail(&t
[1], &m
);
669 ret
= spi_sync(trf
->spi
, &m
);
671 dev_err(trf
->dev
, "%s - Can't send tx data: %d\n", __func__
,
679 trf
->state
= TRF7970A_ST_WAIT_FOR_TX_FIFO
;
680 timeout
= TRF7970A_WAIT_FOR_FIFO_DRAIN_TIMEOUT
;
682 if (trf
->issue_eof
) {
683 trf
->state
= TRF7970A_ST_WAIT_TO_ISSUE_EOF
;
684 timeout
= TRF7970A_WAIT_TO_ISSUE_ISO15693_EOF
;
686 trf
->state
= TRF7970A_ST_WAIT_FOR_RX_DATA
;
689 timeout
= TRF7970A_WAIT_FOR_TX_IRQ
;
691 timeout
= trf
->timeout
;
695 dev_dbg(trf
->dev
, "Setting timeout for %d ms, state: %d\n", timeout
,
698 schedule_delayed_work(&trf
->timeout_work
, msecs_to_jiffies(timeout
));
703 static void trf7970a_fill_fifo(struct trf7970a
*trf
)
705 struct sk_buff
*skb
= trf
->tx_skb
;
711 ret
= trf7970a_read(trf
, TRF7970A_FIFO_STATUS
, &fifo_bytes
);
713 trf7970a_send_err_upstream(trf
, ret
);
717 dev_dbg(trf
->dev
, "Filling FIFO - fifo_bytes: 0x%x\n", fifo_bytes
);
719 fifo_bytes
&= ~TRF7970A_FIFO_STATUS_OVERFLOW
;
721 /* Calculate how much more data can be written to the fifo */
722 len
= TRF7970A_FIFO_SIZE
- fifo_bytes
;
724 schedule_delayed_work(&trf
->timeout_work
,
725 msecs_to_jiffies(TRF7970A_WAIT_FOR_FIFO_DRAIN_TIMEOUT
));
729 len
= min(skb
->len
, len
);
731 prefix
= TRF7970A_CMD_BIT_CONTINUOUS
| TRF7970A_FIFO_IO_REGISTER
;
733 ret
= trf7970a_transmit(trf
, skb
, len
, &prefix
, sizeof(prefix
));
735 trf7970a_send_err_upstream(trf
, ret
);
738 static void trf7970a_drain_fifo(struct trf7970a
*trf
, u8 status
)
740 struct sk_buff
*skb
= trf
->rx_skb
;
744 if (status
& TRF7970A_IRQ_STATUS_ERROR
) {
745 trf7970a_send_err_upstream(trf
, -EIO
);
749 ret
= trf7970a_read(trf
, TRF7970A_FIFO_STATUS
, &fifo_bytes
);
751 trf7970a_send_err_upstream(trf
, ret
);
755 dev_dbg(trf
->dev
, "Draining FIFO - fifo_bytes: 0x%x\n", fifo_bytes
);
757 fifo_bytes
&= ~TRF7970A_FIFO_STATUS_OVERFLOW
;
762 if (fifo_bytes
> skb_tailroom(skb
)) {
763 skb
= skb_copy_expand(skb
, skb_headroom(skb
),
764 max_t(int, fifo_bytes
,
765 TRF7970A_RX_SKB_ALLOC_SIZE
),
768 trf7970a_send_err_upstream(trf
, -ENOMEM
);
772 kfree_skb(trf
->rx_skb
);
776 ret
= trf7970a_read_cont(trf
, TRF7970A_FIFO_IO_REGISTER
,
777 skb_put(skb
, fifo_bytes
), fifo_bytes
);
779 trf7970a_send_err_upstream(trf
, ret
);
783 /* If received Type 2 ACK/NACK, shift right 4 bits and pass up */
784 if ((trf
->framing
== NFC_DIGITAL_FRAMING_NFCA_T2T
) && (skb
->len
== 1) &&
785 (trf
->special_fcn_reg1
== TRF7970A_SPECIAL_FCN_REG1_4_BIT_RX
)) {
787 status
= TRF7970A_IRQ_STATUS_SRX
;
789 trf
->state
= TRF7970A_ST_WAIT_FOR_RX_DATA_CONT
;
791 ret
= trf7970a_read(trf
, TRF7970A_FIFO_STATUS
, &fifo_bytes
);
793 trf7970a_send_err_upstream(trf
, ret
);
797 fifo_bytes
&= ~TRF7970A_FIFO_STATUS_OVERFLOW
;
799 /* If there are bytes in the FIFO, set status to '0' so
800 * the if stmt below doesn't fire and the driver will wait
801 * for the trf7970a to generate another RX interrupt.
808 if (status
== TRF7970A_IRQ_STATUS_SRX
) { /* Receive complete */
809 trf7970a_send_upstream(trf
);
813 dev_dbg(trf
->dev
, "Setting timeout for %d ms\n",
814 TRF7970A_WAIT_FOR_RX_DATA_TIMEOUT
);
816 schedule_delayed_work(&trf
->timeout_work
,
817 msecs_to_jiffies(TRF7970A_WAIT_FOR_RX_DATA_TIMEOUT
));
820 static irqreturn_t
trf7970a_irq(int irq
, void *dev_id
)
822 struct trf7970a
*trf
= dev_id
;
824 u8 status
, fifo_bytes
, iso_ctrl
;
826 mutex_lock(&trf
->lock
);
828 if (trf
->state
== TRF7970A_ST_RF_OFF
) {
829 mutex_unlock(&trf
->lock
);
833 ret
= trf7970a_read_irqstatus(trf
, &status
);
835 mutex_unlock(&trf
->lock
);
839 dev_dbg(trf
->dev
, "IRQ - state: %d, status: 0x%x\n", trf
->state
,
843 mutex_unlock(&trf
->lock
);
847 switch (trf
->state
) {
848 case TRF7970A_ST_IDLE
:
849 case TRF7970A_ST_IDLE_RX_BLOCKED
:
850 /* If initiator and getting interrupts caused by RF noise,
851 * turn off the receiver to avoid unnecessary interrupts.
852 * It will be turned back on in trf7970a_send_cmd() when
853 * the next command is issued.
855 if (trf
->is_initiator
&& (status
& TRF7970A_IRQ_STATUS_ERROR
)) {
856 trf7970a_cmd(trf
, TRF7970A_CMD_BLOCK_RX
);
857 trf
->state
= TRF7970A_ST_IDLE_RX_BLOCKED
;
860 trf7970a_cmd(trf
, TRF7970A_CMD_FIFO_RESET
);
862 case TRF7970A_ST_WAIT_FOR_TX_FIFO
:
863 if (status
& TRF7970A_IRQ_STATUS_TX
) {
864 trf
->ignore_timeout
=
865 !cancel_delayed_work(&trf
->timeout_work
);
866 trf7970a_fill_fifo(trf
);
868 trf7970a_send_err_upstream(trf
, -EIO
);
871 case TRF7970A_ST_WAIT_FOR_RX_DATA
:
872 case TRF7970A_ST_WAIT_FOR_RX_DATA_CONT
:
873 if (status
& TRF7970A_IRQ_STATUS_SRX
) {
874 trf
->ignore_timeout
=
875 !cancel_delayed_work(&trf
->timeout_work
);
876 trf7970a_drain_fifo(trf
, status
);
877 } else if (status
& TRF7970A_IRQ_STATUS_FIFO
) {
878 ret
= trf7970a_read(trf
, TRF7970A_FIFO_STATUS
,
881 fifo_bytes
&= ~TRF7970A_FIFO_STATUS_OVERFLOW
;
884 trf7970a_send_err_upstream(trf
, ret
);
885 else if (!fifo_bytes
)
886 trf7970a_cmd(trf
, TRF7970A_CMD_FIFO_RESET
);
887 } else if ((status
== TRF7970A_IRQ_STATUS_TX
) ||
888 (!trf
->is_initiator
&&
889 (status
== (TRF7970A_IRQ_STATUS_TX
|
890 TRF7970A_IRQ_STATUS_NFC_RF
)))) {
891 trf7970a_cmd(trf
, TRF7970A_CMD_FIFO_RESET
);
894 trf
->ignore_timeout
=
895 !cancel_delayed_work(&trf
->timeout_work
);
896 trf
->rx_skb
= ERR_PTR(0);
897 trf7970a_send_upstream(trf
);
901 if (trf
->is_initiator
)
904 iso_ctrl
= trf
->iso_ctrl
;
906 switch (trf
->framing
) {
907 case NFC_DIGITAL_FRAMING_NFCA_STANDARD
:
908 trf
->tx_cmd
= TRF7970A_CMD_TRANSMIT_NO_CRC
;
909 iso_ctrl
|= TRF7970A_ISO_CTRL_RX_CRC_N
;
910 trf
->iso_ctrl
= 0xff; /* Force ISO_CTRL write */
912 case NFC_DIGITAL_FRAMING_NFCA_STANDARD_WITH_CRC_A
:
913 trf
->tx_cmd
= TRF7970A_CMD_TRANSMIT
;
914 iso_ctrl
&= ~TRF7970A_ISO_CTRL_RX_CRC_N
;
915 trf
->iso_ctrl
= 0xff; /* Force ISO_CTRL write */
917 case NFC_DIGITAL_FRAMING_NFCA_ANTICOL_COMPLETE
:
918 ret
= trf7970a_write(trf
,
919 TRF7970A_SPECIAL_FCN_REG1
,
920 TRF7970A_SPECIAL_FCN_REG1_14_ANTICOLL
);
922 goto err_unlock_exit
;
924 trf
->special_fcn_reg1
=
925 TRF7970A_SPECIAL_FCN_REG1_14_ANTICOLL
;
931 if (iso_ctrl
!= trf
->iso_ctrl
) {
932 ret
= trf7970a_write(trf
, TRF7970A_ISO_CTRL
,
935 goto err_unlock_exit
;
937 trf
->iso_ctrl
= iso_ctrl
;
940 trf7970a_send_err_upstream(trf
, -EIO
);
943 case TRF7970A_ST_WAIT_TO_ISSUE_EOF
:
944 if (status
!= TRF7970A_IRQ_STATUS_TX
)
945 trf7970a_send_err_upstream(trf
, -EIO
);
947 case TRF7970A_ST_LISTENING
:
948 if (status
& TRF7970A_IRQ_STATUS_SRX
) {
949 trf
->ignore_timeout
=
950 !cancel_delayed_work(&trf
->timeout_work
);
951 trf7970a_drain_fifo(trf
, status
);
952 } else if (!(status
& TRF7970A_IRQ_STATUS_NFC_RF
)) {
953 trf7970a_send_err_upstream(trf
, -EIO
);
956 case TRF7970A_ST_LISTENING_MD
:
957 if (status
& TRF7970A_IRQ_STATUS_SRX
) {
958 trf
->ignore_timeout
=
959 !cancel_delayed_work(&trf
->timeout_work
);
961 ret
= trf7970a_mode_detect(trf
, &trf
->md_rf_tech
);
963 trf7970a_send_err_upstream(trf
, ret
);
965 trf
->state
= TRF7970A_ST_LISTENING
;
966 trf7970a_drain_fifo(trf
, status
);
968 } else if (!(status
& TRF7970A_IRQ_STATUS_NFC_RF
)) {
969 trf7970a_send_err_upstream(trf
, -EIO
);
973 dev_err(trf
->dev
, "%s - Driver in invalid state: %d\n",
974 __func__
, trf
->state
);
978 mutex_unlock(&trf
->lock
);
982 static void trf7970a_issue_eof(struct trf7970a
*trf
)
986 dev_dbg(trf
->dev
, "Issuing EOF\n");
988 ret
= trf7970a_cmd(trf
, TRF7970A_CMD_FIFO_RESET
);
990 trf7970a_send_err_upstream(trf
, ret
);
992 ret
= trf7970a_cmd(trf
, TRF7970A_CMD_EOF
);
994 trf7970a_send_err_upstream(trf
, ret
);
996 trf
->state
= TRF7970A_ST_WAIT_FOR_RX_DATA
;
998 dev_dbg(trf
->dev
, "Setting timeout for %d ms, state: %d\n",
999 trf
->timeout
, trf
->state
);
1001 schedule_delayed_work(&trf
->timeout_work
,
1002 msecs_to_jiffies(trf
->timeout
));
1005 static void trf7970a_timeout_work_handler(struct work_struct
*work
)
1007 struct trf7970a
*trf
= container_of(work
, struct trf7970a
,
1010 dev_dbg(trf
->dev
, "Timeout - state: %d, ignore_timeout: %d\n",
1011 trf
->state
, trf
->ignore_timeout
);
1013 mutex_lock(&trf
->lock
);
1015 if (trf
->ignore_timeout
)
1016 trf
->ignore_timeout
= false;
1017 else if (trf
->state
== TRF7970A_ST_WAIT_FOR_RX_DATA_CONT
)
1018 trf7970a_drain_fifo(trf
, TRF7970A_IRQ_STATUS_SRX
);
1019 else if (trf
->state
== TRF7970A_ST_WAIT_TO_ISSUE_EOF
)
1020 trf7970a_issue_eof(trf
);
1022 trf7970a_send_err_upstream(trf
, -ETIMEDOUT
);
1024 mutex_unlock(&trf
->lock
);
1027 static int trf7970a_init(struct trf7970a
*trf
)
1031 dev_dbg(trf
->dev
, "Initializing device - state: %d\n", trf
->state
);
1033 ret
= trf7970a_cmd(trf
, TRF7970A_CMD_SOFT_INIT
);
1037 ret
= trf7970a_cmd(trf
, TRF7970A_CMD_IDLE
);
1041 ret
= trf7970a_write(trf
, TRF7970A_REG_IO_CTRL
,
1042 trf
->io_ctrl
| TRF7970A_REG_IO_CTRL_VRS(0x1));
1046 ret
= trf7970a_write(trf
, TRF7970A_NFC_TARGET_LEVEL
, 0);
1050 usleep_range(1000, 2000);
1052 trf
->chip_status_ctrl
&= ~TRF7970A_CHIP_STATUS_RF_ON
;
1054 ret
= trf7970a_write(trf
, TRF7970A_MODULATOR_SYS_CLK_CTRL
,
1055 trf
->modulator_sys_clk_ctrl
);
1059 ret
= trf7970a_write(trf
, TRF7970A_ADJUTABLE_FIFO_IRQ_LEVELS
,
1060 TRF7970A_ADJUTABLE_FIFO_IRQ_LEVELS_WLH_96
|
1061 TRF7970A_ADJUTABLE_FIFO_IRQ_LEVELS_WLL_32
);
1065 ret
= trf7970a_write(trf
, TRF7970A_SPECIAL_FCN_REG1
, 0);
1069 trf
->special_fcn_reg1
= 0;
1071 trf
->iso_ctrl
= 0xff;
1075 dev_dbg(trf
->dev
, "Couldn't init device: %d\n", ret
);
1079 static void trf7970a_switch_rf_off(struct trf7970a
*trf
)
1081 if ((trf
->state
== TRF7970A_ST_PWR_OFF
) ||
1082 (trf
->state
== TRF7970A_ST_RF_OFF
))
1085 dev_dbg(trf
->dev
, "Switching rf off\n");
1087 trf
->chip_status_ctrl
&= ~TRF7970A_CHIP_STATUS_RF_ON
;
1089 trf7970a_write(trf
, TRF7970A_CHIP_STATUS_CTRL
, trf
->chip_status_ctrl
);
1091 trf
->aborting
= false;
1092 trf
->state
= TRF7970A_ST_RF_OFF
;
1094 pm_runtime_mark_last_busy(trf
->dev
);
1095 pm_runtime_put_autosuspend(trf
->dev
);
1098 static int trf7970a_switch_rf_on(struct trf7970a
*trf
)
1102 dev_dbg(trf
->dev
, "Switching rf on\n");
1104 pm_runtime_get_sync(trf
->dev
);
1106 if (trf
->state
!= TRF7970A_ST_RF_OFF
) { /* Power on, RF off */
1107 dev_err(trf
->dev
, "%s - Incorrect state: %d\n", __func__
,
1112 ret
= trf7970a_init(trf
);
1114 dev_err(trf
->dev
, "%s - Can't initialize: %d\n", __func__
, ret
);
1118 trf
->state
= TRF7970A_ST_IDLE
;
1123 static int trf7970a_switch_rf(struct nfc_digital_dev
*ddev
, bool on
)
1125 struct trf7970a
*trf
= nfc_digital_get_drvdata(ddev
);
1128 dev_dbg(trf
->dev
, "Switching RF - state: %d, on: %d\n", trf
->state
, on
);
1130 mutex_lock(&trf
->lock
);
1133 switch (trf
->state
) {
1134 case TRF7970A_ST_PWR_OFF
:
1135 case TRF7970A_ST_RF_OFF
:
1136 ret
= trf7970a_switch_rf_on(trf
);
1138 case TRF7970A_ST_IDLE
:
1139 case TRF7970A_ST_IDLE_RX_BLOCKED
:
1142 dev_err(trf
->dev
, "%s - Invalid request: %d %d\n",
1143 __func__
, trf
->state
, on
);
1144 trf7970a_switch_rf_off(trf
);
1148 switch (trf
->state
) {
1149 case TRF7970A_ST_PWR_OFF
:
1150 case TRF7970A_ST_RF_OFF
:
1153 dev_err(trf
->dev
, "%s - Invalid request: %d %d\n",
1154 __func__
, trf
->state
, on
);
1157 case TRF7970A_ST_IDLE
:
1158 case TRF7970A_ST_IDLE_RX_BLOCKED
:
1159 case TRF7970A_ST_WAIT_FOR_RX_DATA
:
1160 case TRF7970A_ST_WAIT_FOR_RX_DATA_CONT
:
1161 trf7970a_switch_rf_off(trf
);
1165 mutex_unlock(&trf
->lock
);
1169 static int trf7970a_in_config_rf_tech(struct trf7970a
*trf
, int tech
)
1173 dev_dbg(trf
->dev
, "rf technology: %d\n", tech
);
1176 case NFC_DIGITAL_RF_TECH_106A
:
1177 trf
->iso_ctrl_tech
= TRF7970A_ISO_CTRL_14443A_106
;
1178 trf
->modulator_sys_clk_ctrl
=
1179 (trf
->modulator_sys_clk_ctrl
& 0xf8) |
1180 TRF7970A_MODULATOR_DEPTH_OOK
;
1181 trf
->guard_time
= TRF7970A_GUARD_TIME_NFCA
;
1183 case NFC_DIGITAL_RF_TECH_106B
:
1184 trf
->iso_ctrl_tech
= TRF7970A_ISO_CTRL_14443B_106
;
1185 trf
->modulator_sys_clk_ctrl
=
1186 (trf
->modulator_sys_clk_ctrl
& 0xf8) |
1187 TRF7970A_MODULATOR_DEPTH_ASK10
;
1188 trf
->guard_time
= TRF7970A_GUARD_TIME_NFCB
;
1190 case NFC_DIGITAL_RF_TECH_212F
:
1191 trf
->iso_ctrl_tech
= TRF7970A_ISO_CTRL_FELICA_212
;
1192 trf
->modulator_sys_clk_ctrl
=
1193 (trf
->modulator_sys_clk_ctrl
& 0xf8) |
1194 TRF7970A_MODULATOR_DEPTH_ASK10
;
1195 trf
->guard_time
= TRF7970A_GUARD_TIME_NFCF
;
1197 case NFC_DIGITAL_RF_TECH_424F
:
1198 trf
->iso_ctrl_tech
= TRF7970A_ISO_CTRL_FELICA_424
;
1199 trf
->modulator_sys_clk_ctrl
=
1200 (trf
->modulator_sys_clk_ctrl
& 0xf8) |
1201 TRF7970A_MODULATOR_DEPTH_ASK10
;
1202 trf
->guard_time
= TRF7970A_GUARD_TIME_NFCF
;
1204 case NFC_DIGITAL_RF_TECH_ISO15693
:
1205 trf
->iso_ctrl_tech
= TRF7970A_ISO_CTRL_15693_SGL_1OF4_2648
;
1206 trf
->modulator_sys_clk_ctrl
=
1207 (trf
->modulator_sys_clk_ctrl
& 0xf8) |
1208 TRF7970A_MODULATOR_DEPTH_OOK
;
1209 trf
->guard_time
= TRF7970A_GUARD_TIME_15693
;
1212 dev_dbg(trf
->dev
, "Unsupported rf technology: %d\n", tech
);
1216 trf
->technology
= tech
;
1218 /* If in initiator mode and not changing the RF tech due to a
1219 * PSL sequence (indicated by 'trf->iso_ctrl == 0xff' from
1220 * trf7970a_init()), clear the NFC Target Detection Level register
1223 if (trf
->iso_ctrl
== 0xff)
1224 ret
= trf7970a_write(trf
, TRF7970A_NFC_TARGET_LEVEL
, 0);
1229 static int trf7970a_is_rf_field(struct trf7970a
*trf
, bool *is_rf_field
)
1234 ret
= trf7970a_write(trf
, TRF7970A_CHIP_STATUS_CTRL
,
1235 trf
->chip_status_ctrl
|
1236 TRF7970A_CHIP_STATUS_REC_ON
);
1240 ret
= trf7970a_cmd(trf
, TRF7970A_CMD_TEST_EXT_RF
);
1244 usleep_range(50, 60);
1246 ret
= trf7970a_read(trf
, TRF7970A_RSSI_OSC_STATUS
, &rssi
);
1250 ret
= trf7970a_write(trf
, TRF7970A_CHIP_STATUS_CTRL
,
1251 trf
->chip_status_ctrl
);
1255 if (rssi
& TRF7970A_RSSI_OSC_STATUS_RSSI_MASK
)
1256 *is_rf_field
= true;
1258 *is_rf_field
= false;
1263 static int trf7970a_in_config_framing(struct trf7970a
*trf
, int framing
)
1265 u8 iso_ctrl
= trf
->iso_ctrl_tech
;
1266 bool is_rf_field
= false;
1269 dev_dbg(trf
->dev
, "framing: %d\n", framing
);
1272 case NFC_DIGITAL_FRAMING_NFCA_SHORT
:
1273 case NFC_DIGITAL_FRAMING_NFCA_STANDARD
:
1274 trf
->tx_cmd
= TRF7970A_CMD_TRANSMIT_NO_CRC
;
1275 iso_ctrl
|= TRF7970A_ISO_CTRL_RX_CRC_N
;
1277 case NFC_DIGITAL_FRAMING_NFCA_STANDARD_WITH_CRC_A
:
1278 case NFC_DIGITAL_FRAMING_NFCA_T4T
:
1279 case NFC_DIGITAL_FRAMING_NFCB
:
1280 case NFC_DIGITAL_FRAMING_NFCB_T4T
:
1281 case NFC_DIGITAL_FRAMING_NFCF
:
1282 case NFC_DIGITAL_FRAMING_NFCF_T3T
:
1283 case NFC_DIGITAL_FRAMING_ISO15693_INVENTORY
:
1284 case NFC_DIGITAL_FRAMING_ISO15693_T5T
:
1285 case NFC_DIGITAL_FRAMING_NFCA_NFC_DEP
:
1286 case NFC_DIGITAL_FRAMING_NFCF_NFC_DEP
:
1287 trf
->tx_cmd
= TRF7970A_CMD_TRANSMIT
;
1288 iso_ctrl
&= ~TRF7970A_ISO_CTRL_RX_CRC_N
;
1290 case NFC_DIGITAL_FRAMING_NFCA_T2T
:
1291 trf
->tx_cmd
= TRF7970A_CMD_TRANSMIT
;
1292 iso_ctrl
|= TRF7970A_ISO_CTRL_RX_CRC_N
;
1295 dev_dbg(trf
->dev
, "Unsupported Framing: %d\n", framing
);
1299 trf
->framing
= framing
;
1301 if (!(trf
->chip_status_ctrl
& TRF7970A_CHIP_STATUS_RF_ON
)) {
1302 ret
= trf7970a_is_rf_field(trf
, &is_rf_field
);
1310 if (iso_ctrl
!= trf
->iso_ctrl
) {
1311 ret
= trf7970a_write(trf
, TRF7970A_ISO_CTRL
, iso_ctrl
);
1315 trf
->iso_ctrl
= iso_ctrl
;
1317 ret
= trf7970a_write(trf
, TRF7970A_MODULATOR_SYS_CLK_CTRL
,
1318 trf
->modulator_sys_clk_ctrl
);
1323 if (!(trf
->chip_status_ctrl
& TRF7970A_CHIP_STATUS_RF_ON
)) {
1324 ret
= trf7970a_write(trf
, TRF7970A_CHIP_STATUS_CTRL
,
1325 trf
->chip_status_ctrl
|
1326 TRF7970A_CHIP_STATUS_RF_ON
);
1330 trf
->chip_status_ctrl
|= TRF7970A_CHIP_STATUS_RF_ON
;
1332 usleep_range(trf
->guard_time
, trf
->guard_time
+ 1000);
1338 static int trf7970a_in_configure_hw(struct nfc_digital_dev
*ddev
, int type
,
1341 struct trf7970a
*trf
= nfc_digital_get_drvdata(ddev
);
1344 dev_dbg(trf
->dev
, "Configure hw - type: %d, param: %d\n", type
, param
);
1346 mutex_lock(&trf
->lock
);
1348 trf
->is_initiator
= true;
1350 if ((trf
->state
== TRF7970A_ST_PWR_OFF
) ||
1351 (trf
->state
== TRF7970A_ST_RF_OFF
)) {
1352 ret
= trf7970a_switch_rf_on(trf
);
1358 case NFC_DIGITAL_CONFIG_RF_TECH
:
1359 ret
= trf7970a_in_config_rf_tech(trf
, param
);
1361 case NFC_DIGITAL_CONFIG_FRAMING
:
1362 ret
= trf7970a_in_config_framing(trf
, param
);
1365 dev_dbg(trf
->dev
, "Unknown type: %d\n", type
);
1370 mutex_unlock(&trf
->lock
);
1374 static int trf7970a_is_iso15693_write_or_lock(u8 cmd
)
1377 case ISO15693_CMD_WRITE_SINGLE_BLOCK
:
1378 case ISO15693_CMD_LOCK_BLOCK
:
1379 case ISO15693_CMD_WRITE_MULTIPLE_BLOCK
:
1380 case ISO15693_CMD_WRITE_AFI
:
1381 case ISO15693_CMD_LOCK_AFI
:
1382 case ISO15693_CMD_WRITE_DSFID
:
1383 case ISO15693_CMD_LOCK_DSFID
:
1390 static int trf7970a_per_cmd_config(struct trf7970a
*trf
, struct sk_buff
*skb
)
1392 u8
*req
= skb
->data
;
1393 u8 special_fcn_reg1
, iso_ctrl
;
1396 trf
->issue_eof
= false;
1398 /* When issuing Type 2 read command, make sure the '4_bit_RX' bit in
1399 * special functions register 1 is cleared; otherwise, its a write or
1400 * sector select command and '4_bit_RX' must be set.
1402 * When issuing an ISO 15693 command, inspect the flags byte to see
1403 * what speed to use. Also, remember if the OPTION flag is set on
1404 * a Type 5 write or lock command so the driver will know that it
1405 * has to send an EOF in order to get a response.
1407 if ((trf
->technology
== NFC_DIGITAL_RF_TECH_106A
) &&
1408 (trf
->framing
== NFC_DIGITAL_FRAMING_NFCA_T2T
)) {
1409 if (req
[0] == NFC_T2T_CMD_READ
)
1410 special_fcn_reg1
= 0;
1412 special_fcn_reg1
= TRF7970A_SPECIAL_FCN_REG1_4_BIT_RX
;
1414 if (special_fcn_reg1
!= trf
->special_fcn_reg1
) {
1415 ret
= trf7970a_write(trf
, TRF7970A_SPECIAL_FCN_REG1
,
1420 trf
->special_fcn_reg1
= special_fcn_reg1
;
1422 } else if (trf
->technology
== NFC_DIGITAL_RF_TECH_ISO15693
) {
1423 iso_ctrl
= trf
->iso_ctrl
& ~TRF7970A_ISO_CTRL_RFID_SPEED_MASK
;
1425 switch (req
[0] & ISO15693_REQ_FLAG_SPEED_MASK
) {
1427 iso_ctrl
|= TRF7970A_ISO_CTRL_15693_SGL_1OF4_662
;
1429 case ISO15693_REQ_FLAG_SUB_CARRIER
:
1430 iso_ctrl
|= TRF7970A_ISO_CTRL_15693_DBL_1OF4_667a
;
1432 case ISO15693_REQ_FLAG_DATA_RATE
:
1433 iso_ctrl
|= TRF7970A_ISO_CTRL_15693_SGL_1OF4_2648
;
1435 case (ISO15693_REQ_FLAG_SUB_CARRIER
|
1436 ISO15693_REQ_FLAG_DATA_RATE
):
1437 iso_ctrl
|= TRF7970A_ISO_CTRL_15693_DBL_1OF4_2669
;
1441 if (iso_ctrl
!= trf
->iso_ctrl
) {
1442 ret
= trf7970a_write(trf
, TRF7970A_ISO_CTRL
, iso_ctrl
);
1446 trf
->iso_ctrl
= iso_ctrl
;
1449 if ((trf
->framing
== NFC_DIGITAL_FRAMING_ISO15693_T5T
) &&
1450 trf7970a_is_iso15693_write_or_lock(req
[1]) &&
1451 (req
[0] & ISO15693_REQ_FLAG_OPTION
))
1452 trf
->issue_eof
= true;
1458 static int trf7970a_send_cmd(struct nfc_digital_dev
*ddev
,
1459 struct sk_buff
*skb
, u16 timeout
,
1460 nfc_digital_cmd_complete_t cb
, void *arg
)
1462 struct trf7970a
*trf
= nfc_digital_get_drvdata(ddev
);
1468 dev_dbg(trf
->dev
, "New request - state: %d, timeout: %d ms, len: %d\n",
1469 trf
->state
, timeout
, skb
->len
);
1471 if (skb
->len
> TRF7970A_TX_MAX
)
1474 mutex_lock(&trf
->lock
);
1476 if ((trf
->state
!= TRF7970A_ST_IDLE
) &&
1477 (trf
->state
!= TRF7970A_ST_IDLE_RX_BLOCKED
)) {
1478 dev_err(trf
->dev
, "%s - Bogus state: %d\n", __func__
,
1484 if (trf
->aborting
) {
1485 dev_dbg(trf
->dev
, "Abort process complete\n");
1486 trf
->aborting
= false;
1492 trf
->rx_skb
= nfc_alloc_recv_skb(TRF7970A_RX_SKB_ALLOC_SIZE
,
1495 dev_dbg(trf
->dev
, "Can't alloc rx_skb\n");
1501 if (trf
->state
== TRF7970A_ST_IDLE_RX_BLOCKED
) {
1502 ret
= trf7970a_cmd(trf
, TRF7970A_CMD_ENABLE_RX
);
1506 trf
->state
= TRF7970A_ST_IDLE
;
1509 if (trf
->is_initiator
) {
1510 ret
= trf7970a_per_cmd_config(trf
, skb
);
1519 trf
->timeout
= timeout
;
1520 trf
->ignore_timeout
= false;
1524 /* TX data must be prefixed with a FIFO reset cmd, a cmd that depends
1525 * on what the current framing is, the address of the TX length byte 1
1526 * register (0x1d), and the 2 byte length of the data to be transmitted.
1527 * That totals 5 bytes.
1529 prefix
[0] = TRF7970A_CMD_BIT_CTRL
|
1530 TRF7970A_CMD_BIT_OPCODE(TRF7970A_CMD_FIFO_RESET
);
1531 prefix
[1] = TRF7970A_CMD_BIT_CTRL
|
1532 TRF7970A_CMD_BIT_OPCODE(trf
->tx_cmd
);
1533 prefix
[2] = TRF7970A_CMD_BIT_CONTINUOUS
| TRF7970A_TX_LENGTH_BYTE1
;
1535 if (trf
->framing
== NFC_DIGITAL_FRAMING_NFCA_SHORT
) {
1537 prefix
[4] = 0x0f; /* 7 bits */
1539 prefix
[3] = (len
& 0xf00) >> 4;
1540 prefix
[3] |= ((len
& 0xf0) >> 4);
1541 prefix
[4] = ((len
& 0x0f) << 4);
1544 len
= min_t(int, skb
->len
, TRF7970A_FIFO_SIZE
);
1546 /* Clear possible spurious interrupt */
1547 ret
= trf7970a_read_irqstatus(trf
, &status
);
1551 ret
= trf7970a_transmit(trf
, skb
, len
, prefix
, sizeof(prefix
));
1553 kfree_skb(trf
->rx_skb
);
1558 mutex_unlock(&trf
->lock
);
1562 static int trf7970a_tg_config_rf_tech(struct trf7970a
*trf
, int tech
)
1566 dev_dbg(trf
->dev
, "rf technology: %d\n", tech
);
1569 case NFC_DIGITAL_RF_TECH_106A
:
1570 trf
->iso_ctrl_tech
= TRF7970A_ISO_CTRL_NFC_NFC_CE_MODE
|
1571 TRF7970A_ISO_CTRL_NFC_CE
| TRF7970A_ISO_CTRL_NFC_CE_14443A
;
1572 trf
->modulator_sys_clk_ctrl
=
1573 (trf
->modulator_sys_clk_ctrl
& 0xf8) |
1574 TRF7970A_MODULATOR_DEPTH_OOK
;
1576 case NFC_DIGITAL_RF_TECH_212F
:
1577 trf
->iso_ctrl_tech
= TRF7970A_ISO_CTRL_NFC_NFC_CE_MODE
|
1578 TRF7970A_ISO_CTRL_NFC_NFCF_212
;
1579 trf
->modulator_sys_clk_ctrl
=
1580 (trf
->modulator_sys_clk_ctrl
& 0xf8) |
1581 TRF7970A_MODULATOR_DEPTH_ASK10
;
1583 case NFC_DIGITAL_RF_TECH_424F
:
1584 trf
->iso_ctrl_tech
= TRF7970A_ISO_CTRL_NFC_NFC_CE_MODE
|
1585 TRF7970A_ISO_CTRL_NFC_NFCF_424
;
1586 trf
->modulator_sys_clk_ctrl
=
1587 (trf
->modulator_sys_clk_ctrl
& 0xf8) |
1588 TRF7970A_MODULATOR_DEPTH_ASK10
;
1591 dev_dbg(trf
->dev
, "Unsupported rf technology: %d\n", tech
);
1595 trf
->technology
= tech
;
1597 /* Normally we write the ISO_CTRL register in
1598 * trf7970a_tg_config_framing() because the framing can change
1599 * the value written. However, when sending a PSL RES,
1600 * digital_tg_send_psl_res_complete() doesn't call
1601 * trf7970a_tg_config_framing() so we must write the register
1604 if ((trf
->framing
== NFC_DIGITAL_FRAMING_NFC_DEP_ACTIVATED
) &&
1605 (trf
->iso_ctrl_tech
!= trf
->iso_ctrl
)) {
1606 ret
= trf7970a_write(trf
, TRF7970A_ISO_CTRL
,
1607 trf
->iso_ctrl_tech
);
1609 trf
->iso_ctrl
= trf
->iso_ctrl_tech
;
1615 /* Since this is a target routine, several of the framing calls are
1616 * made between receiving the request and sending the response so they
1617 * should take effect until after the response is sent. This is accomplished
1618 * by skipping the ISO_CTRL register write here and doing it in the interrupt
1621 static int trf7970a_tg_config_framing(struct trf7970a
*trf
, int framing
)
1623 u8 iso_ctrl
= trf
->iso_ctrl_tech
;
1626 dev_dbg(trf
->dev
, "framing: %d\n", framing
);
1629 case NFC_DIGITAL_FRAMING_NFCA_NFC_DEP
:
1630 trf
->tx_cmd
= TRF7970A_CMD_TRANSMIT_NO_CRC
;
1631 iso_ctrl
|= TRF7970A_ISO_CTRL_RX_CRC_N
;
1633 case NFC_DIGITAL_FRAMING_NFCA_STANDARD
:
1634 case NFC_DIGITAL_FRAMING_NFCA_STANDARD_WITH_CRC_A
:
1635 case NFC_DIGITAL_FRAMING_NFCA_ANTICOL_COMPLETE
:
1636 /* These ones are applied in the interrupt handler */
1637 iso_ctrl
= trf
->iso_ctrl
; /* Don't write to ISO_CTRL yet */
1639 case NFC_DIGITAL_FRAMING_NFCF_NFC_DEP
:
1640 trf
->tx_cmd
= TRF7970A_CMD_TRANSMIT
;
1641 iso_ctrl
&= ~TRF7970A_ISO_CTRL_RX_CRC_N
;
1643 case NFC_DIGITAL_FRAMING_NFC_DEP_ACTIVATED
:
1644 trf
->tx_cmd
= TRF7970A_CMD_TRANSMIT
;
1645 iso_ctrl
&= ~TRF7970A_ISO_CTRL_RX_CRC_N
;
1648 dev_dbg(trf
->dev
, "Unsupported Framing: %d\n", framing
);
1652 trf
->framing
= framing
;
1654 if (iso_ctrl
!= trf
->iso_ctrl
) {
1655 ret
= trf7970a_write(trf
, TRF7970A_ISO_CTRL
, iso_ctrl
);
1659 trf
->iso_ctrl
= iso_ctrl
;
1661 ret
= trf7970a_write(trf
, TRF7970A_MODULATOR_SYS_CLK_CTRL
,
1662 trf
->modulator_sys_clk_ctrl
);
1667 if (!(trf
->chip_status_ctrl
& TRF7970A_CHIP_STATUS_RF_ON
)) {
1668 ret
= trf7970a_write(trf
, TRF7970A_CHIP_STATUS_CTRL
,
1669 trf
->chip_status_ctrl
|
1670 TRF7970A_CHIP_STATUS_RF_ON
);
1674 trf
->chip_status_ctrl
|= TRF7970A_CHIP_STATUS_RF_ON
;
1680 static int trf7970a_tg_configure_hw(struct nfc_digital_dev
*ddev
, int type
,
1683 struct trf7970a
*trf
= nfc_digital_get_drvdata(ddev
);
1686 dev_dbg(trf
->dev
, "Configure hw - type: %d, param: %d\n", type
, param
);
1688 mutex_lock(&trf
->lock
);
1690 trf
->is_initiator
= false;
1692 if ((trf
->state
== TRF7970A_ST_PWR_OFF
) ||
1693 (trf
->state
== TRF7970A_ST_RF_OFF
)) {
1694 ret
= trf7970a_switch_rf_on(trf
);
1700 case NFC_DIGITAL_CONFIG_RF_TECH
:
1701 ret
= trf7970a_tg_config_rf_tech(trf
, param
);
1703 case NFC_DIGITAL_CONFIG_FRAMING
:
1704 ret
= trf7970a_tg_config_framing(trf
, param
);
1707 dev_dbg(trf
->dev
, "Unknown type: %d\n", type
);
1712 mutex_unlock(&trf
->lock
);
1716 static int _trf7970a_tg_listen(struct nfc_digital_dev
*ddev
, u16 timeout
,
1717 nfc_digital_cmd_complete_t cb
, void *arg
,
1720 struct trf7970a
*trf
= nfc_digital_get_drvdata(ddev
);
1723 mutex_lock(&trf
->lock
);
1725 if ((trf
->state
!= TRF7970A_ST_IDLE
) &&
1726 (trf
->state
!= TRF7970A_ST_IDLE_RX_BLOCKED
)) {
1727 dev_err(trf
->dev
, "%s - Bogus state: %d\n", __func__
,
1733 if (trf
->aborting
) {
1734 dev_dbg(trf
->dev
, "Abort process complete\n");
1735 trf
->aborting
= false;
1740 trf
->rx_skb
= nfc_alloc_recv_skb(TRF7970A_RX_SKB_ALLOC_SIZE
,
1743 dev_dbg(trf
->dev
, "Can't alloc rx_skb\n");
1748 ret
= trf7970a_write(trf
, TRF7970A_RX_SPECIAL_SETTINGS
,
1749 TRF7970A_RX_SPECIAL_SETTINGS_HBT
|
1750 TRF7970A_RX_SPECIAL_SETTINGS_M848
|
1751 TRF7970A_RX_SPECIAL_SETTINGS_C424
|
1752 TRF7970A_RX_SPECIAL_SETTINGS_C212
);
1756 ret
= trf7970a_write(trf
, TRF7970A_REG_IO_CTRL
,
1757 trf
->io_ctrl
| TRF7970A_REG_IO_CTRL_VRS(0x1));
1761 ret
= trf7970a_write(trf
, TRF7970A_NFC_LOW_FIELD_LEVEL
,
1762 TRF7970A_NFC_LOW_FIELD_LEVEL_RFDET(0x3));
1766 ret
= trf7970a_write(trf
, TRF7970A_NFC_TARGET_LEVEL
,
1767 TRF7970A_NFC_TARGET_LEVEL_RFDET(0x7));
1774 trf
->timeout
= timeout
;
1775 trf
->ignore_timeout
= false;
1777 ret
= trf7970a_cmd(trf
, TRF7970A_CMD_ENABLE_RX
);
1781 trf
->state
= mode_detect
? TRF7970A_ST_LISTENING_MD
:
1782 TRF7970A_ST_LISTENING
;
1784 schedule_delayed_work(&trf
->timeout_work
, msecs_to_jiffies(timeout
));
1787 mutex_unlock(&trf
->lock
);
1791 static int trf7970a_tg_listen(struct nfc_digital_dev
*ddev
, u16 timeout
,
1792 nfc_digital_cmd_complete_t cb
, void *arg
)
1794 struct trf7970a
*trf
= nfc_digital_get_drvdata(ddev
);
1796 dev_dbg(trf
->dev
, "Listen - state: %d, timeout: %d ms\n",
1797 trf
->state
, timeout
);
1799 return _trf7970a_tg_listen(ddev
, timeout
, cb
, arg
, false);
1802 static int trf7970a_tg_listen_md(struct nfc_digital_dev
*ddev
,
1803 u16 timeout
, nfc_digital_cmd_complete_t cb
,
1806 struct trf7970a
*trf
= nfc_digital_get_drvdata(ddev
);
1809 dev_dbg(trf
->dev
, "Listen MD - state: %d, timeout: %d ms\n",
1810 trf
->state
, timeout
);
1812 ret
= trf7970a_tg_configure_hw(ddev
, NFC_DIGITAL_CONFIG_RF_TECH
,
1813 NFC_DIGITAL_RF_TECH_106A
);
1817 ret
= trf7970a_tg_configure_hw(ddev
, NFC_DIGITAL_CONFIG_FRAMING
,
1818 NFC_DIGITAL_FRAMING_NFCA_NFC_DEP
);
1822 return _trf7970a_tg_listen(ddev
, timeout
, cb
, arg
, true);
1825 static int trf7970a_tg_get_rf_tech(struct nfc_digital_dev
*ddev
, u8
*rf_tech
)
1827 struct trf7970a
*trf
= nfc_digital_get_drvdata(ddev
);
1829 dev_dbg(trf
->dev
, "Get RF Tech - state: %d, rf_tech: %d\n",
1830 trf
->state
, trf
->md_rf_tech
);
1832 *rf_tech
= trf
->md_rf_tech
;
1837 static void trf7970a_abort_cmd(struct nfc_digital_dev
*ddev
)
1839 struct trf7970a
*trf
= nfc_digital_get_drvdata(ddev
);
1841 dev_dbg(trf
->dev
, "Abort process initiated\n");
1843 mutex_lock(&trf
->lock
);
1845 switch (trf
->state
) {
1846 case TRF7970A_ST_WAIT_FOR_TX_FIFO
:
1847 case TRF7970A_ST_WAIT_FOR_RX_DATA
:
1848 case TRF7970A_ST_WAIT_FOR_RX_DATA_CONT
:
1849 case TRF7970A_ST_WAIT_TO_ISSUE_EOF
:
1850 trf
->aborting
= true;
1852 case TRF7970A_ST_LISTENING
:
1853 trf
->ignore_timeout
= !cancel_delayed_work(&trf
->timeout_work
);
1854 trf7970a_send_err_upstream(trf
, -ECANCELED
);
1855 dev_dbg(trf
->dev
, "Abort process complete\n");
1861 mutex_unlock(&trf
->lock
);
1864 static struct nfc_digital_ops trf7970a_nfc_ops
= {
1865 .in_configure_hw
= trf7970a_in_configure_hw
,
1866 .in_send_cmd
= trf7970a_send_cmd
,
1867 .tg_configure_hw
= trf7970a_tg_configure_hw
,
1868 .tg_send_cmd
= trf7970a_send_cmd
,
1869 .tg_listen
= trf7970a_tg_listen
,
1870 .tg_listen_md
= trf7970a_tg_listen_md
,
1871 .tg_get_rf_tech
= trf7970a_tg_get_rf_tech
,
1872 .switch_rf
= trf7970a_switch_rf
,
1873 .abort_cmd
= trf7970a_abort_cmd
,
1876 static int trf7970a_power_up(struct trf7970a
*trf
)
1880 dev_dbg(trf
->dev
, "Powering up - state: %d\n", trf
->state
);
1882 if (trf
->state
!= TRF7970A_ST_PWR_OFF
)
1885 ret
= regulator_enable(trf
->regulator
);
1887 dev_err(trf
->dev
, "%s - Can't enable VIN: %d\n", __func__
, ret
);
1891 usleep_range(5000, 6000);
1893 if (trf
->en2_gpiod
&&
1894 !(trf
->quirks
& TRF7970A_QUIRK_EN2_MUST_STAY_LOW
)) {
1895 gpiod_set_value_cansleep(trf
->en2_gpiod
, 1);
1896 usleep_range(1000, 2000);
1899 gpiod_set_value_cansleep(trf
->en_gpiod
, 1);
1901 usleep_range(20000, 21000);
1903 trf
->state
= TRF7970A_ST_RF_OFF
;
1908 static int trf7970a_power_down(struct trf7970a
*trf
)
1912 dev_dbg(trf
->dev
, "Powering down - state: %d\n", trf
->state
);
1914 if (trf
->state
== TRF7970A_ST_PWR_OFF
)
1917 if (trf
->state
!= TRF7970A_ST_RF_OFF
) {
1918 dev_dbg(trf
->dev
, "Can't power down - not RF_OFF state (%d)\n",
1923 gpiod_set_value_cansleep(trf
->en_gpiod
, 0);
1925 if (trf
->en2_gpiod
&& !(trf
->quirks
& TRF7970A_QUIRK_EN2_MUST_STAY_LOW
))
1926 gpiod_set_value_cansleep(trf
->en2_gpiod
, 0);
1928 ret
= regulator_disable(trf
->regulator
);
1930 dev_err(trf
->dev
, "%s - Can't disable VIN: %d\n", __func__
,
1933 trf
->state
= TRF7970A_ST_PWR_OFF
;
1938 static int trf7970a_startup(struct trf7970a
*trf
)
1942 ret
= trf7970a_power_up(trf
);
1946 pm_runtime_set_active(trf
->dev
);
1947 pm_runtime_enable(trf
->dev
);
1948 pm_runtime_mark_last_busy(trf
->dev
);
1953 static void trf7970a_shutdown(struct trf7970a
*trf
)
1955 switch (trf
->state
) {
1956 case TRF7970A_ST_WAIT_FOR_TX_FIFO
:
1957 case TRF7970A_ST_WAIT_FOR_RX_DATA
:
1958 case TRF7970A_ST_WAIT_FOR_RX_DATA_CONT
:
1959 case TRF7970A_ST_WAIT_TO_ISSUE_EOF
:
1960 case TRF7970A_ST_LISTENING
:
1961 trf7970a_send_err_upstream(trf
, -ECANCELED
);
1963 case TRF7970A_ST_IDLE
:
1964 case TRF7970A_ST_IDLE_RX_BLOCKED
:
1965 trf7970a_switch_rf_off(trf
);
1971 pm_runtime_disable(trf
->dev
);
1972 pm_runtime_set_suspended(trf
->dev
);
1974 trf7970a_power_down(trf
);
1977 static int trf7970a_get_autosuspend_delay(struct device_node
*np
)
1979 int autosuspend_delay
, ret
;
1981 ret
= of_property_read_u32(np
, "autosuspend-delay", &autosuspend_delay
);
1983 autosuspend_delay
= TRF7970A_AUTOSUSPEND_DELAY
;
1985 return autosuspend_delay
;
1988 static int trf7970a_probe(struct spi_device
*spi
)
1990 struct device_node
*np
= spi
->dev
.of_node
;
1991 struct trf7970a
*trf
;
1992 int uvolts
, autosuspend_delay
, ret
;
1993 u32 clk_freq
= TRF7970A_13MHZ_CLOCK_FREQUENCY
;
1996 dev_err(&spi
->dev
, "No Device Tree entry\n");
2000 trf
= devm_kzalloc(&spi
->dev
, sizeof(*trf
), GFP_KERNEL
);
2004 trf
->state
= TRF7970A_ST_PWR_OFF
;
2005 trf
->dev
= &spi
->dev
;
2008 spi
->mode
= SPI_MODE_1
;
2009 spi
->bits_per_word
= 8;
2011 ret
= spi_setup(spi
);
2013 dev_err(trf
->dev
, "Can't set up SPI Communication\n");
2017 if (of_property_read_bool(np
, "irq-status-read-quirk"))
2018 trf
->quirks
|= TRF7970A_QUIRK_IRQ_STATUS_READ
;
2020 /* There are two enable pins - only EN must be present in the DT */
2021 trf
->en_gpiod
= devm_gpiod_get_index(trf
->dev
, "ti,enable", 0,
2023 if (IS_ERR(trf
->en_gpiod
)) {
2024 dev_err(trf
->dev
, "No EN GPIO property\n");
2025 return PTR_ERR(trf
->en_gpiod
);
2028 trf
->en2_gpiod
= devm_gpiod_get_index_optional(trf
->dev
, "ti,enable", 1,
2030 if (!trf
->en2_gpiod
) {
2031 dev_info(trf
->dev
, "No EN2 GPIO property\n");
2032 } else if (IS_ERR(trf
->en2_gpiod
)) {
2033 dev_err(trf
->dev
, "Error getting EN2 GPIO property: %ld\n",
2034 PTR_ERR(trf
->en2_gpiod
));
2035 return PTR_ERR(trf
->en2_gpiod
);
2036 } else if (of_property_read_bool(np
, "en2-rf-quirk")) {
2037 trf
->quirks
|= TRF7970A_QUIRK_EN2_MUST_STAY_LOW
;
2040 of_property_read_u32(np
, "clock-frequency", &clk_freq
);
2041 if ((clk_freq
!= TRF7970A_27MHZ_CLOCK_FREQUENCY
) &&
2042 (clk_freq
!= TRF7970A_13MHZ_CLOCK_FREQUENCY
)) {
2044 "clock-frequency (%u Hz) unsupported\n", clk_freq
);
2048 if (clk_freq
== TRF7970A_27MHZ_CLOCK_FREQUENCY
) {
2049 trf
->modulator_sys_clk_ctrl
= TRF7970A_MODULATOR_27MHZ
;
2050 dev_dbg(trf
->dev
, "trf7970a configured for 27MHz crystal\n");
2052 trf
->modulator_sys_clk_ctrl
= 0;
2055 ret
= devm_request_threaded_irq(trf
->dev
, spi
->irq
, NULL
,
2057 IRQF_TRIGGER_RISING
| IRQF_ONESHOT
,
2060 dev_err(trf
->dev
, "Can't request IRQ#%d: %d\n", spi
->irq
, ret
);
2064 mutex_init(&trf
->lock
);
2065 INIT_DELAYED_WORK(&trf
->timeout_work
, trf7970a_timeout_work_handler
);
2067 trf
->regulator
= devm_regulator_get(&spi
->dev
, "vin");
2068 if (IS_ERR(trf
->regulator
)) {
2069 ret
= PTR_ERR(trf
->regulator
);
2070 dev_err(trf
->dev
, "Can't get VIN regulator: %d\n", ret
);
2071 goto err_destroy_lock
;
2074 ret
= regulator_enable(trf
->regulator
);
2076 dev_err(trf
->dev
, "Can't enable VIN: %d\n", ret
);
2077 goto err_destroy_lock
;
2080 uvolts
= regulator_get_voltage(trf
->regulator
);
2081 if (uvolts
> 4000000)
2082 trf
->chip_status_ctrl
= TRF7970A_CHIP_STATUS_VRS5_3
;
2084 trf
->regulator
= devm_regulator_get(&spi
->dev
, "vdd-io");
2085 if (IS_ERR(trf
->regulator
)) {
2086 ret
= PTR_ERR(trf
->regulator
);
2087 dev_err(trf
->dev
, "Can't get VDD_IO regulator: %d\n", ret
);
2088 goto err_destroy_lock
;
2091 ret
= regulator_enable(trf
->regulator
);
2093 dev_err(trf
->dev
, "Can't enable VDD_IO: %d\n", ret
);
2094 goto err_destroy_lock
;
2097 if (regulator_get_voltage(trf
->regulator
) == 1800000) {
2098 trf
->io_ctrl
= TRF7970A_REG_IO_CTRL_IO_LOW
;
2099 dev_dbg(trf
->dev
, "trf7970a config vdd_io to 1.8V\n");
2102 trf
->ddev
= nfc_digital_allocate_device(&trf7970a_nfc_ops
,
2103 TRF7970A_SUPPORTED_PROTOCOLS
,
2104 NFC_DIGITAL_DRV_CAPS_IN_CRC
|
2105 NFC_DIGITAL_DRV_CAPS_TG_CRC
, 0,
2108 dev_err(trf
->dev
, "Can't allocate NFC digital device\n");
2110 goto err_disable_regulator
;
2113 nfc_digital_set_parent_dev(trf
->ddev
, trf
->dev
);
2114 nfc_digital_set_drvdata(trf
->ddev
, trf
);
2115 spi_set_drvdata(spi
, trf
);
2117 autosuspend_delay
= trf7970a_get_autosuspend_delay(np
);
2119 pm_runtime_set_autosuspend_delay(trf
->dev
, autosuspend_delay
);
2120 pm_runtime_use_autosuspend(trf
->dev
);
2122 ret
= trf7970a_startup(trf
);
2126 ret
= nfc_digital_register_device(trf
->ddev
);
2128 dev_err(trf
->dev
, "Can't register NFC digital device: %d\n",
2136 trf7970a_shutdown(trf
);
2138 nfc_digital_free_device(trf
->ddev
);
2139 err_disable_regulator
:
2140 regulator_disable(trf
->regulator
);
2142 mutex_destroy(&trf
->lock
);
2146 static int trf7970a_remove(struct spi_device
*spi
)
2148 struct trf7970a
*trf
= spi_get_drvdata(spi
);
2150 mutex_lock(&trf
->lock
);
2152 trf7970a_shutdown(trf
);
2154 mutex_unlock(&trf
->lock
);
2156 nfc_digital_unregister_device(trf
->ddev
);
2157 nfc_digital_free_device(trf
->ddev
);
2159 regulator_disable(trf
->regulator
);
2161 mutex_destroy(&trf
->lock
);
2166 #ifdef CONFIG_PM_SLEEP
2167 static int trf7970a_suspend(struct device
*dev
)
2169 struct spi_device
*spi
= to_spi_device(dev
);
2170 struct trf7970a
*trf
= spi_get_drvdata(spi
);
2172 dev_dbg(dev
, "Suspend\n");
2174 mutex_lock(&trf
->lock
);
2176 trf7970a_shutdown(trf
);
2178 mutex_unlock(&trf
->lock
);
2183 static int trf7970a_resume(struct device
*dev
)
2185 struct spi_device
*spi
= to_spi_device(dev
);
2186 struct trf7970a
*trf
= spi_get_drvdata(spi
);
2189 dev_dbg(dev
, "Resume\n");
2191 mutex_lock(&trf
->lock
);
2193 ret
= trf7970a_startup(trf
);
2195 mutex_unlock(&trf
->lock
);
2202 static int trf7970a_pm_runtime_suspend(struct device
*dev
)
2204 struct spi_device
*spi
= to_spi_device(dev
);
2205 struct trf7970a
*trf
= spi_get_drvdata(spi
);
2208 dev_dbg(dev
, "Runtime suspend\n");
2210 mutex_lock(&trf
->lock
);
2212 ret
= trf7970a_power_down(trf
);
2214 mutex_unlock(&trf
->lock
);
2219 static int trf7970a_pm_runtime_resume(struct device
*dev
)
2221 struct spi_device
*spi
= to_spi_device(dev
);
2222 struct trf7970a
*trf
= spi_get_drvdata(spi
);
2225 dev_dbg(dev
, "Runtime resume\n");
2227 ret
= trf7970a_power_up(trf
);
2229 pm_runtime_mark_last_busy(dev
);
2235 static const struct dev_pm_ops trf7970a_pm_ops
= {
2236 SET_SYSTEM_SLEEP_PM_OPS(trf7970a_suspend
, trf7970a_resume
)
2237 SET_RUNTIME_PM_OPS(trf7970a_pm_runtime_suspend
,
2238 trf7970a_pm_runtime_resume
, NULL
)
2241 static const struct of_device_id trf7970a_of_match
[] = {
2242 {.compatible
= "ti,trf7970a",},
2246 MODULE_DEVICE_TABLE(of
, trf7970a_of_match
);
2248 static const struct spi_device_id trf7970a_id_table
[] = {
2253 MODULE_DEVICE_TABLE(spi
, trf7970a_id_table
);
2255 static struct spi_driver trf7970a_spi_driver
= {
2256 .probe
= trf7970a_probe
,
2257 .remove
= trf7970a_remove
,
2258 .id_table
= trf7970a_id_table
,
2261 .of_match_table
= of_match_ptr(trf7970a_of_match
),
2262 .pm
= &trf7970a_pm_ops
,
2266 module_spi_driver(trf7970a_spi_driver
);
2268 MODULE_AUTHOR("Mark A. Greer <mgreer@animalcreek.com>");
2269 MODULE_LICENSE("GPL v2");
2270 MODULE_DESCRIPTION("TI trf7970a RFID/NFC Transceiver Driver");