drivers/usb/host/xhci-rcar.c

   1 // SPDX-License-Identifier: GPL-2.0
   2 /*
   3  * xHCI host controller driver for R-Car SoCs
   4  *
   5  * Copyright (C) 2014 Renesas Electronics Corporation
   6  */
   7
   8 #include <linux/firmware.h>
   9 #include <linux/iopoll.h>
  10 #include <linux/module.h>
  11 #include <linux/platform_device.h>
  12 #include <linux/of.h>
  13 #include <linux/usb/phy.h>
  14 #include <linux/sys_soc.h>
  15
  16 #include "xhci.h"
  17 #include "xhci-plat.h"
  18 #include "xhci-rcar.h"
  19
  20 /*
  21 * - The V3 firmware is for almost all R-Car Gen3 (except r8a7795 ES1.x)
  22 * - The V2 firmware is for r8a7795 ES1.x.
  23 * - The V2 firmware is possible to use on R-Car Gen2. However, the V2 causes
  24 *   performance degradation. So, this driver continues to use the V1 if R-Car
  25 *   Gen2.
  26 * - The V1 firmware is impossible to use on R-Car Gen3.
  27 */
  28 MODULE_FIRMWARE(XHCI_RCAR_FIRMWARE_NAME_V1);
  29 MODULE_FIRMWARE(XHCI_RCAR_FIRMWARE_NAME_V2);
  30 MODULE_FIRMWARE(XHCI_RCAR_FIRMWARE_NAME_V3);
  31
  32 /*** Register Offset ***/
  33 #define RCAR_USB3_AXH_STA       0x104   /* AXI Host Control Status */
  34 #define RCAR_USB3_INT_ENA       0x224   /* Interrupt Enable */
  35 #define RCAR_USB3_DL_CTRL       0x250   /* FW Download Control & Status */
  36 #define RCAR_USB3_FW_DATA0      0x258   /* FW Data0 */
  37
  38 #define RCAR_USB3_LCLK          0xa44   /* LCLK Select */
  39 #define RCAR_USB3_CONF1         0xa48   /* USB3.0 Configuration1 */
  40 #define RCAR_USB3_CONF2         0xa5c   /* USB3.0 Configuration2 */
  41 #define RCAR_USB3_CONF3         0xaa8   /* USB3.0 Configuration3 */
  42 #define RCAR_USB3_RX_POL        0xab0   /* USB3.0 RX Polarity */
  43 #define RCAR_USB3_TX_POL        0xab8   /* USB3.0 TX Polarity */
  44
  45 /*** Register Settings ***/
  46 /* AXI Host Control Status */
  47 #define RCAR_USB3_AXH_STA_B3_PLL_ACTIVE         0x00010000
  48 #define RCAR_USB3_AXH_STA_B2_PLL_ACTIVE         0x00000001
  49 #define RCAR_USB3_AXH_STA_PLL_ACTIVE_MASK (RCAR_USB3_AXH_STA_B3_PLL_ACTIVE | \
  50                                            RCAR_USB3_AXH_STA_B2_PLL_ACTIVE)
  51
  52 /* Interrupt Enable */
  53 #define RCAR_USB3_INT_XHC_ENA   0x00000001
  54 #define RCAR_USB3_INT_PME_ENA   0x00000002
  55 #define RCAR_USB3_INT_HSE_ENA   0x00000004
  56 #define RCAR_USB3_INT_ENA_VAL   (RCAR_USB3_INT_XHC_ENA | \
  57                                 RCAR_USB3_INT_PME_ENA | RCAR_USB3_INT_HSE_ENA)
  58
  59 /* FW Download Control & Status */
  60 #define RCAR_USB3_DL_CTRL_ENABLE        0x00000001
  61 #define RCAR_USB3_DL_CTRL_FW_SUCCESS    0x00000010
  62 #define RCAR_USB3_DL_CTRL_FW_SET_DATA0  0x00000100
  63
  64 /* LCLK Select */
  65 #define RCAR_USB3_LCLK_ENA_VAL  0x01030001
  66
  67 /* USB3.0 Configuration */
  68 #define RCAR_USB3_CONF1_VAL     0x00030204
  69 #define RCAR_USB3_CONF2_VAL     0x00030300
  70 #define RCAR_USB3_CONF3_VAL     0x13802007
  71
  72 /* USB3.0 Polarity */
  73 #define RCAR_USB3_RX_POL_VAL    BIT(21)
  74 #define RCAR_USB3_TX_POL_VAL    BIT(4)
  75
  76 /* For soc_device_attribute */
  77 #define RCAR_XHCI_FIRMWARE_V2   BIT(0) /* FIRMWARE V2 */
  78 #define RCAR_XHCI_FIRMWARE_V3   BIT(1) /* FIRMWARE V3 */
  79
  80 static const struct soc_device_attribute rcar_quirks_match[]  = {
  81         {
  82                 .soc_id = "r8a7795", .revision = "ES1.*",
  83                 .data = (void *)RCAR_XHCI_FIRMWARE_V2,
  84         },
  85         { /* sentinel */ },
  86 };
  87
  88 static void xhci_rcar_start_gen2(struct usb_hcd *hcd)
  89 {
  90         /* LCLK Select */
  91         writel(RCAR_USB3_LCLK_ENA_VAL, hcd->regs + RCAR_USB3_LCLK);
  92         /* USB3.0 Configuration */
  93         writel(RCAR_USB3_CONF1_VAL, hcd->regs + RCAR_USB3_CONF1);
  94         writel(RCAR_USB3_CONF2_VAL, hcd->regs + RCAR_USB3_CONF2);
  95         writel(RCAR_USB3_CONF3_VAL, hcd->regs + RCAR_USB3_CONF3);
  96         /* USB3.0 Polarity */
  97         writel(RCAR_USB3_RX_POL_VAL, hcd->regs + RCAR_USB3_RX_POL);
  98         writel(RCAR_USB3_TX_POL_VAL, hcd->regs + RCAR_USB3_TX_POL);
  99 }
 100
 101 static int xhci_rcar_is_gen2(struct device *dev)
 102 {
 103         struct device_node *node = dev->of_node;
 104
 105         return of_device_is_compatible(node, "renesas,xhci-r8a7790") ||
 106                 of_device_is_compatible(node, "renesas,xhci-r8a7791") ||
 107                 of_device_is_compatible(node, "renesas,xhci-r8a7793") ||
 108                 of_device_is_compatible(node, "renesas,rcar-gen2-xhci");
 109 }
 110
 111 void xhci_rcar_start(struct usb_hcd *hcd)
 112 {
 113         u32 temp;
 114
 115         if (hcd->regs != NULL) {
 116                 /* Interrupt Enable */
 117                 temp = readl(hcd->regs + RCAR_USB3_INT_ENA);
 118                 temp |= RCAR_USB3_INT_ENA_VAL;
 119                 writel(temp, hcd->regs + RCAR_USB3_INT_ENA);
 120                 if (xhci_rcar_is_gen2(hcd->self.controller))
 121                         xhci_rcar_start_gen2(hcd);
 122         }
 123 }
 124
 125 static int xhci_rcar_download_firmware(struct usb_hcd *hcd)
 126 {
 127         struct device *dev = hcd->self.controller;
 128         void __iomem *regs = hcd->regs;
 129         struct xhci_plat_priv *priv = hcd_to_xhci_priv(hcd);
 130         const struct firmware *fw;
 131         int retval, index, j;
 132         u32 data, val, temp;
 133         u32 quirks = 0;
 134         const struct soc_device_attribute *attr;
 135         const char *firmware_name;
 136
 137         attr = soc_device_match(rcar_quirks_match);
 138         if (attr)
 139                 quirks = (uintptr_t)attr->data;
 140
 141         if (quirks & RCAR_XHCI_FIRMWARE_V2)
 142                 firmware_name = XHCI_RCAR_FIRMWARE_NAME_V2;
 143         else if (quirks & RCAR_XHCI_FIRMWARE_V3)
 144                 firmware_name = XHCI_RCAR_FIRMWARE_NAME_V3;
 145         else
 146                 firmware_name = priv->firmware_name;
 147
 148         /* request R-Car USB3.0 firmware */
 149         retval = request_firmware(&fw, firmware_name, dev);
 150         if (retval)
 151                 return retval;
 152
 153         /* download R-Car USB3.0 firmware */
 154         temp = readl(regs + RCAR_USB3_DL_CTRL);
 155         temp |= RCAR_USB3_DL_CTRL_ENABLE;
 156         writel(temp, regs + RCAR_USB3_DL_CTRL);
 157
 158         for (index = 0; index < fw->size; index += 4) {
 159                 /* to avoid reading beyond the end of the buffer */
 160                 for (data = 0, j = 3; j >= 0; j--) {
 161                         if ((j + index) < fw->size)
 162                                 data |= fw->data[index + j] << (8 * j);
 163                 }
 164                 writel(data, regs + RCAR_USB3_FW_DATA0);
 165                 temp = readl(regs + RCAR_USB3_DL_CTRL);
 166                 temp |= RCAR_USB3_DL_CTRL_FW_SET_DATA0;
 167                 writel(temp, regs + RCAR_USB3_DL_CTRL);
 168
 169                 retval = readl_poll_timeout_atomic(regs + RCAR_USB3_DL_CTRL,
 170                                 val, !(val & RCAR_USB3_DL_CTRL_FW_SET_DATA0),
 171                                 1, 10000);
 172                 if (retval < 0)
 173                         break;
 174         }
 175
 176         temp = readl(regs + RCAR_USB3_DL_CTRL);
 177         temp &= ~RCAR_USB3_DL_CTRL_ENABLE;
 178         writel(temp, regs + RCAR_USB3_DL_CTRL);
 179
 180         retval = readl_poll_timeout_atomic((regs + RCAR_USB3_DL_CTRL),
 181                         val, val & RCAR_USB3_DL_CTRL_FW_SUCCESS, 1, 10000);
 182
 183         release_firmware(fw);
 184
 185         return retval;
 186 }
 187
 188 static bool xhci_rcar_wait_for_pll_active(struct usb_hcd *hcd)
 189 {
 190         int retval;
 191         u32 val, mask = RCAR_USB3_AXH_STA_PLL_ACTIVE_MASK;
 192
 193         retval = readl_poll_timeout_atomic(hcd->regs + RCAR_USB3_AXH_STA,
 194                         val, (val & mask) == mask, 1, 1000);
 195         return !retval;
 196 }
 197
 198 /* This function needs to initialize a "phy" of usb before */
 199 int xhci_rcar_init_quirk(struct usb_hcd *hcd)
 200 {
 201         /* If hcd->regs is NULL, we don't just call the following function */
 202         if (!hcd->regs)
 203                 return 0;
 204
 205         if (!xhci_rcar_wait_for_pll_active(hcd))
 206                 return -ETIMEDOUT;
 207
 208         return xhci_rcar_download_firmware(hcd);
 209 }
 210
 211 int xhci_rcar_resume_quirk(struct usb_hcd *hcd)
 212 {
 213         int ret;
 214
 215         ret = xhci_rcar_download_firmware(hcd);
 216         if (!ret)
 217                 xhci_rcar_start(hcd);
 218
 219         return ret;
 220 }