Merge tag 'trace-v5.11-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt...

[linux/fpc-iii.git] / drivers / video / fbdev / aty / mach64_ct.c

// SPDX-License-Identifier: GPL-2.0

/*
 *  ATI Mach64 CT/VT/GT/LT Support
 */

#include <linux/fb.h>
#include <linux/delay.h>
#include <asm/io.h>
#include <video/mach64.h>
#include "atyfb.h"
#ifdef CONFIG_PPC
#include <asm/machdep.h>
#endif

#undef DEBUG

static int aty_valid_pll_ct (const struct fb_info *info, u32 vclk_per, struct pll_ct *pll);
static int aty_dsp_gt       (const struct fb_info *info, u32 bpp, struct pll_ct *pll);
static int aty_var_to_pll_ct(const struct fb_info *info, u32 vclk_per, u32 bpp, union aty_pll *pll);
static u32 aty_pll_to_var_ct(const struct fb_info *info, const union aty_pll *pll);

u8 aty_ld_pll_ct(int offset, const struct atyfb_par *par)
{
        u8 res;

        /* write addr byte */
        aty_st_8(CLOCK_CNTL_ADDR, (offset << 2) & PLL_ADDR, par);
        /* read the register value */
        res = aty_ld_8(CLOCK_CNTL_DATA, par);
        return res;
}

static void aty_st_pll_ct(int offset, u8 val, const struct atyfb_par *par)
{
        /* write addr byte */
        aty_st_8(CLOCK_CNTL_ADDR, ((offset << 2) & PLL_ADDR) | PLL_WR_EN, par);
        /* write the register value */
        aty_st_8(CLOCK_CNTL_DATA, val & PLL_DATA, par);
        aty_st_8(CLOCK_CNTL_ADDR, ((offset << 2) & PLL_ADDR) & ~PLL_WR_EN, par);
}

/*
 * by Daniel Mantione
 *                                  <daniel.mantione@freepascal.org>
 *
 *
 * ATI Mach64 CT clock synthesis description.
 *
 * All clocks on the Mach64 can be calculated using the same principle:
 *
 *       XTALIN * x * FB_DIV
 * CLK = ----------------------
 *       PLL_REF_DIV * POST_DIV
 *
 * XTALIN is a fixed speed clock. Common speeds are 14.31 MHz and 29.50 MHz.
 * PLL_REF_DIV can be set by the user, but is the same for all clocks.
 * FB_DIV can be set by the user for each clock individually, it should be set
 * between 128 and 255, the chip will generate a bad clock signal for too low
 * values.
 * x depends on the type of clock; usually it is 2, but for the MCLK it can also
 * be set to 4.
 * POST_DIV can be set by the user for each clock individually, Possible values
 * are 1,2,4,8 and for some clocks other values are available too.
 * CLK is of course the clock speed that is generated.
 *
 * The Mach64 has these clocks:
 *
 * MCLK                 The clock rate of the chip
 * XCLK                 The clock rate of the on-chip memory
 * VCLK0                First pixel clock of first CRT controller
 * VCLK1    Second pixel clock of first CRT controller
 * VCLK2                Third pixel clock of first CRT controller
 * VCLK3    Fourth pixel clock of first CRT controller
 * VCLK                 Selected pixel clock, one of VCLK0, VCLK1, VCLK2, VCLK3
 * V2CLK                Pixel clock of the second CRT controller.
 * SCLK                 Multi-purpose clock
 *
 * - MCLK and XCLK use the same FB_DIV
 * - VCLK0 .. VCLK3 use the same FB_DIV
 * - V2CLK is needed when the second CRTC is used (can be used for dualhead);
 *   i.e. CRT monitor connected to laptop has different resolution than built
 *   in LCD monitor.
 * - SCLK is not available on all cards; it is know to exist on the Rage LT-PRO,
 *   Rage XL and Rage Mobility. It is know not to exist on the Mach64 VT.
 * - V2CLK is not available on all cards, most likely only the Rage LT-PRO,
 *   the Rage XL and the Rage Mobility
 *
 * SCLK can be used to:
 * - Clock the chip instead of MCLK
 * - Replace XTALIN with a user defined frequency
 * - Generate the pixel clock for the LCD monitor (instead of VCLK)
 */

 /*
  * It can be quite hard to calculate XCLK and MCLK if they don't run at the
  * same frequency. Luckily, until now all cards that need asynchrone clock
  * speeds seem to have SCLK.
  * So this driver uses SCLK to clock the chip and XCLK to clock the memory.
  */

/* ------------------------------------------------------------------------- */

/*
 *  PLL programming (Mach64 CT family)
 *
 *
 * This procedure sets the display fifo. The display fifo is a buffer that
 * contains data read from the video memory that waits to be processed by
 * the CRT controller.
 *
 * On the more modern Mach64 variants, the chip doesn't calculate the
 * interval after which the display fifo has to be reloaded from memory
 * automatically, the driver has to do it instead.
 */

#define Maximum_DSP_PRECISION 7
const u8 aty_postdividers[8] = {1,2,4,8,3,5,6,12};

static int aty_dsp_gt(const struct fb_info *info, u32 bpp, struct pll_ct *pll)
{
        u32 dsp_off, dsp_on, dsp_xclks;
        u32 multiplier, divider, ras_multiplier, ras_divider, tmp;
        u8 vshift, xshift;
        s8 dsp_precision;

        multiplier = ((u32)pll->mclk_fb_div) * pll->vclk_post_div_real;
        divider = ((u32)pll->vclk_fb_div) * pll->xclk_ref_div;

        ras_multiplier = pll->xclkmaxrasdelay;
        ras_divider = 1;

        if (bpp>=8)
                divider = divider * (bpp >> 2);

        vshift = (6 - 2) - pll->xclk_post_div;  /* FIFO is 64 bits wide in accelerator mode ... */

        if (bpp == 0)
                vshift--;       /* ... but only 32 bits in VGA mode. */

#ifdef CONFIG_FB_ATY_GENERIC_LCD
        if (pll->xres != 0) {
                struct atyfb_par *par = (struct atyfb_par *) info->par;

                multiplier = multiplier * par->lcd_width;
                divider = divider * pll->xres & ~7;

                ras_multiplier = ras_multiplier * par->lcd_width;
                ras_divider = ras_divider * pll->xres & ~7;
        }
#endif
        /* If we don't do this, 32 bits for multiplier & divider won't be
        enough in certain situations! */
        while (((multiplier | divider) & 1) == 0) {
                multiplier = multiplier >> 1;
                divider = divider >> 1;
        }

        /* Determine DSP precision first */
        tmp = ((multiplier * pll->fifo_size) << vshift) / divider;

        for (dsp_precision = -5;  tmp;  dsp_precision++)
                tmp >>= 1;
        if (dsp_precision < 0)
                dsp_precision = 0;
        else if (dsp_precision > Maximum_DSP_PRECISION)
                dsp_precision = Maximum_DSP_PRECISION;

        xshift = 6 - dsp_precision;
        vshift += xshift;

        /* Move on to dsp_off */
        dsp_off = ((multiplier * (pll->fifo_size - 1)) << vshift) / divider -
                (1 << (vshift - xshift));

/*    if (bpp == 0)
        dsp_on = ((multiplier * 20 << vshift) + divider) / divider;
    else */
        {
                dsp_on = ((multiplier << vshift) + divider) / divider;
                tmp = ((ras_multiplier << xshift) + ras_divider) / ras_divider;
                if (dsp_on < tmp)
                        dsp_on = tmp;
                dsp_on = dsp_on + (tmp * 2) + (pll->xclkpagefaultdelay << xshift);
        }

        /* Calculate rounding factor and apply it to dsp_on */
        tmp = ((1 << (Maximum_DSP_PRECISION - dsp_precision)) - 1) >> 1;
        dsp_on = ((dsp_on + tmp) / (tmp + 1)) * (tmp + 1);

        if (dsp_on >= ((dsp_off / (tmp + 1)) * (tmp + 1))) {
                dsp_on = dsp_off - (multiplier << vshift) / divider;
                dsp_on = (dsp_on / (tmp + 1)) * (tmp + 1);
        }

        /* Last but not least:  dsp_xclks */
        dsp_xclks = ((multiplier << (vshift + 5)) + divider) / divider;

        /* Get register values. */
        pll->dsp_on_off = (dsp_on << 16) + dsp_off;
        pll->dsp_config = (dsp_precision << 20) | (pll->dsp_loop_latency << 16) | dsp_xclks;
#ifdef DEBUG
        printk("atyfb(%s): dsp_config 0x%08x, dsp_on_off 0x%08x\n",
                __func__, pll->dsp_config, pll->dsp_on_off);
#endif
        return 0;
}

static int aty_valid_pll_ct(const struct fb_info *info, u32 vclk_per, struct pll_ct *pll)
{
        u32 q;
        struct atyfb_par *par = (struct atyfb_par *) info->par;
        int pllvclk;

        /* FIXME: use the VTB/GTB /{3,6,12} post dividers if they're better suited */
        q = par->ref_clk_per * pll->pll_ref_div * 4 / vclk_per;
        if (q < 16*8 || q > 255*8) {
                printk(KERN_CRIT "atyfb: vclk out of range\n");
                return -EINVAL;
        } else {
                pll->vclk_post_div  = (q < 128*8);
                pll->vclk_post_div += (q <  64*8);
                pll->vclk_post_div += (q <  32*8);
        }
        pll->vclk_post_div_real = aty_postdividers[pll->vclk_post_div];
        //    pll->vclk_post_div <<= 6;
        pll->vclk_fb_div = q * pll->vclk_post_div_real / 8;
        pllvclk = (1000000 * 2 * pll->vclk_fb_div) /
                (par->ref_clk_per * pll->pll_ref_div);
#ifdef DEBUG
        printk("atyfb(%s): pllvclk=%d MHz, vclk=%d MHz\n",
                __func__, pllvclk, pllvclk / pll->vclk_post_div_real);
#endif
        pll->pll_vclk_cntl = 0x03; /* VCLK = PLL_VCLK/VCLKx_POST */

        /* Set ECP (scaler/overlay clock) divider */
        if (par->pll_limits.ecp_max) {
                int ecp = pllvclk / pll->vclk_post_div_real;
                int ecp_div = 0;

                while (ecp > par->pll_limits.ecp_max && ecp_div < 2) {
                        ecp >>= 1;
                        ecp_div++;
                }
                pll->pll_vclk_cntl |= ecp_div << 4;
        }

        return 0;
}

static int aty_var_to_pll_ct(const struct fb_info *info, u32 vclk_per, u32 bpp, union aty_pll *pll)
{
        struct atyfb_par *par = (struct atyfb_par *) info->par;
        int err;

        if ((err = aty_valid_pll_ct(info, vclk_per, &pll->ct)))
                return err;
        if (M64_HAS(GTB_DSP) && (err = aty_dsp_gt(info, bpp, &pll->ct)))
                return err;
        /*aty_calc_pll_ct(info, &pll->ct);*/
        return 0;
}

static u32 aty_pll_to_var_ct(const struct fb_info *info, const union aty_pll *pll)
{
        struct atyfb_par *par = (struct atyfb_par *) info->par;
        u32 ret;
        ret = par->ref_clk_per * pll->ct.pll_ref_div * pll->ct.vclk_post_div_real / pll->ct.vclk_fb_div / 2;
#ifdef CONFIG_FB_ATY_GENERIC_LCD
        if(pll->ct.xres > 0) {
                ret *= par->lcd_width;
                ret /= pll->ct.xres;
        }
#endif
#ifdef DEBUG
        printk("atyfb(%s): calculated 0x%08X(%i)\n", __func__, ret, ret);
#endif
        return ret;
}

void aty_set_pll_ct(const struct fb_info *info, const union aty_pll *pll)
{
        struct atyfb_par *par = (struct atyfb_par *) info->par;
        u32 crtc_gen_cntl, lcd_gen_cntrl;
        u8 tmp, tmp2;

        lcd_gen_cntrl = 0;
#ifdef DEBUG
        printk("atyfb(%s): about to program:\n"
                "pll_ext_cntl=0x%02x pll_gen_cntl=0x%02x pll_vclk_cntl=0x%02x\n",
                __func__,
                pll->ct.pll_ext_cntl, pll->ct.pll_gen_cntl, pll->ct.pll_vclk_cntl);

        printk("atyfb(%s): setting clock %lu for FeedBackDivider %i, ReferenceDivider %i, PostDivider %i(%i)\n",
                __func__,
                par->clk_wr_offset, pll->ct.vclk_fb_div,
                pll->ct.pll_ref_div, pll->ct.vclk_post_div, pll->ct.vclk_post_div_real);
#endif
#ifdef CONFIG_FB_ATY_GENERIC_LCD
        if (par->lcd_table != 0) {
                /* turn off LCD */
                lcd_gen_cntrl = aty_ld_lcd(LCD_GEN_CNTL, par);
                aty_st_lcd(LCD_GEN_CNTL, lcd_gen_cntrl & ~LCD_ON, par);
        }
#endif
        aty_st_8(CLOCK_CNTL, par->clk_wr_offset | CLOCK_STROBE, par);

        /* Temporarily switch to accelerator mode */
        crtc_gen_cntl = aty_ld_le32(CRTC_GEN_CNTL, par);
        if (!(crtc_gen_cntl & CRTC_EXT_DISP_EN))
                aty_st_le32(CRTC_GEN_CNTL, crtc_gen_cntl | CRTC_EXT_DISP_EN, par);

        /* Reset VCLK generator */
        aty_st_pll_ct(PLL_VCLK_CNTL, pll->ct.pll_vclk_cntl, par);

        /* Set post-divider */
        tmp2 = par->clk_wr_offset << 1;
        tmp = aty_ld_pll_ct(VCLK_POST_DIV, par);
        tmp &= ~(0x03U << tmp2);
        tmp |= ((pll->ct.vclk_post_div & 0x03U) << tmp2);
        aty_st_pll_ct(VCLK_POST_DIV, tmp, par);

        /* Set extended post-divider */
        tmp = aty_ld_pll_ct(PLL_EXT_CNTL, par);
        tmp &= ~(0x10U << par->clk_wr_offset);
        tmp &= 0xF0U;
        tmp |= pll->ct.pll_ext_cntl;
        aty_st_pll_ct(PLL_EXT_CNTL, tmp, par);

        /* Set feedback divider */
        tmp = VCLK0_FB_DIV + par->clk_wr_offset;
        aty_st_pll_ct(tmp, (pll->ct.vclk_fb_div & 0xFFU), par);

        aty_st_pll_ct(PLL_GEN_CNTL, (pll->ct.pll_gen_cntl & (~(PLL_OVERRIDE | PLL_MCLK_RST))) | OSC_EN, par);

        /* End VCLK generator reset */
        aty_st_pll_ct(PLL_VCLK_CNTL, pll->ct.pll_vclk_cntl & ~(PLL_VCLK_RST), par);
        mdelay(5);

        aty_st_pll_ct(PLL_GEN_CNTL, pll->ct.pll_gen_cntl, par);
        aty_st_pll_ct(PLL_VCLK_CNTL, pll->ct.pll_vclk_cntl, par);
        mdelay(1);

        /* Restore mode register */
        if (!(crtc_gen_cntl & CRTC_EXT_DISP_EN))
                aty_st_le32(CRTC_GEN_CNTL, crtc_gen_cntl, par);

        if (M64_HAS(GTB_DSP)) {
                u8 dll_cntl;

                if (M64_HAS(XL_DLL))
                        dll_cntl = 0x80;
                else if (par->ram_type >= SDRAM)
                        dll_cntl = 0xa6;
                else
                        dll_cntl = 0xa0;
                aty_st_pll_ct(DLL_CNTL, dll_cntl, par);
                aty_st_pll_ct(VFC_CNTL, 0x1b, par);
                aty_st_le32(DSP_CONFIG, pll->ct.dsp_config, par);
                aty_st_le32(DSP_ON_OFF, pll->ct.dsp_on_off, par);

                mdelay(10);
                aty_st_pll_ct(DLL_CNTL, dll_cntl, par);
                mdelay(10);
                aty_st_pll_ct(DLL_CNTL, dll_cntl | 0x40, par);
                mdelay(10);
                aty_st_pll_ct(DLL_CNTL, dll_cntl & ~0x40, par);
        }
#ifdef CONFIG_FB_ATY_GENERIC_LCD
        if (par->lcd_table != 0) {
                /* restore LCD */
                aty_st_lcd(LCD_GEN_CNTL, lcd_gen_cntrl, par);
        }
#endif
}

static void aty_get_pll_ct(const struct fb_info *info, union aty_pll *pll)
{
        struct atyfb_par *par = (struct atyfb_par *) info->par;
        u8 tmp, clock;

        clock = aty_ld_8(CLOCK_CNTL, par) & 0x03U;
        tmp = clock << 1;
        pll->ct.vclk_post_div = (aty_ld_pll_ct(VCLK_POST_DIV, par) >> tmp) & 0x03U;

        pll->ct.pll_ext_cntl = aty_ld_pll_ct(PLL_EXT_CNTL, par) & 0x0FU;
        pll->ct.vclk_fb_div = aty_ld_pll_ct(VCLK0_FB_DIV + clock, par) & 0xFFU;
        pll->ct.pll_ref_div = aty_ld_pll_ct(PLL_REF_DIV, par);
        pll->ct.mclk_fb_div = aty_ld_pll_ct(MCLK_FB_DIV, par);

        pll->ct.pll_gen_cntl = aty_ld_pll_ct(PLL_GEN_CNTL, par);
        pll->ct.pll_vclk_cntl = aty_ld_pll_ct(PLL_VCLK_CNTL, par);

        if (M64_HAS(GTB_DSP)) {
                pll->ct.dsp_config = aty_ld_le32(DSP_CONFIG, par);
                pll->ct.dsp_on_off = aty_ld_le32(DSP_ON_OFF, par);
        }
}

static int aty_init_pll_ct(const struct fb_info *info, union aty_pll *pll)
{
        struct atyfb_par *par = (struct atyfb_par *) info->par;
        u8 mpost_div, xpost_div, sclk_post_div_real;
        u32 q, memcntl, trp;
        u32 dsp_config, dsp_on_off, vga_dsp_config, vga_dsp_on_off;
#ifdef DEBUG
        int pllmclk, pllsclk;
#endif
        pll->ct.pll_ext_cntl = aty_ld_pll_ct(PLL_EXT_CNTL, par);
        pll->ct.xclk_post_div = pll->ct.pll_ext_cntl & 0x07;
        pll->ct.xclk_ref_div = 1;
        switch (pll->ct.xclk_post_div) {
        case 0:  case 1:  case 2:  case 3:
                break;

        case 4:
                pll->ct.xclk_ref_div = 3;
                pll->ct.xclk_post_div = 0;
                break;

        default:
                printk(KERN_CRIT "atyfb: Unsupported xclk source:  %d.\n", pll->ct.xclk_post_div);
                return -EINVAL;
        }
        pll->ct.mclk_fb_mult = 2;
        if(pll->ct.pll_ext_cntl & PLL_MFB_TIMES_4_2B) {
                pll->ct.mclk_fb_mult = 4;
                pll->ct.xclk_post_div -= 1;
        }

#ifdef DEBUG
        printk("atyfb(%s): mclk_fb_mult=%d, xclk_post_div=%d\n",
                __func__, pll->ct.mclk_fb_mult, pll->ct.xclk_post_div);
#endif

        memcntl = aty_ld_le32(MEM_CNTL, par);
        trp = (memcntl & 0x300) >> 8;

        pll->ct.xclkpagefaultdelay = ((memcntl & 0xc00) >> 10) + ((memcntl & 0x1000) >> 12) + trp + 2;
        pll->ct.xclkmaxrasdelay = ((memcntl & 0x70000) >> 16) + trp + 2;

        if (M64_HAS(FIFO_32)) {
                pll->ct.fifo_size = 32;
        } else {
                pll->ct.fifo_size = 24;
                pll->ct.xclkpagefaultdelay += 2;
                pll->ct.xclkmaxrasdelay += 3;
        }

        switch (par->ram_type) {
        case DRAM:
                if (info->fix.smem_len<=ONE_MB) {
                        pll->ct.dsp_loop_latency = 10;
                } else {
                        pll->ct.dsp_loop_latency = 8;
                        pll->ct.xclkpagefaultdelay += 2;
                }
                break;
        case EDO:
        case PSEUDO_EDO:
                if (info->fix.smem_len<=ONE_MB) {
                        pll->ct.dsp_loop_latency = 9;
                } else {
                        pll->ct.dsp_loop_latency = 8;
                        pll->ct.xclkpagefaultdelay += 1;
                }
                break;
        case SDRAM:
                if (info->fix.smem_len<=ONE_MB) {
                        pll->ct.dsp_loop_latency = 11;
                } else {
                        pll->ct.dsp_loop_latency = 10;
                        pll->ct.xclkpagefaultdelay += 1;
                }
                break;
        case SGRAM:
                pll->ct.dsp_loop_latency = 8;
                pll->ct.xclkpagefaultdelay += 3;
                break;
        default:
                pll->ct.dsp_loop_latency = 11;
                pll->ct.xclkpagefaultdelay += 3;
                break;
        }

        if (pll->ct.xclkmaxrasdelay <= pll->ct.xclkpagefaultdelay)
                pll->ct.xclkmaxrasdelay = pll->ct.xclkpagefaultdelay + 1;

        /* Allow BIOS to override */
        dsp_config = aty_ld_le32(DSP_CONFIG, par);
        dsp_on_off = aty_ld_le32(DSP_ON_OFF, par);
        vga_dsp_config = aty_ld_le32(VGA_DSP_CONFIG, par);
        vga_dsp_on_off = aty_ld_le32(VGA_DSP_ON_OFF, par);

        if (dsp_config)
                pll->ct.dsp_loop_latency = (dsp_config & DSP_LOOP_LATENCY) >> 16;
#if 0
        FIXME: is it relevant for us?
        if ((!dsp_on_off && !M64_HAS(RESET_3D)) ||
                ((dsp_on_off == vga_dsp_on_off) &&
                (!dsp_config || !((dsp_config ^ vga_dsp_config) & DSP_XCLKS_PER_QW)))) {
                vga_dsp_on_off &= VGA_DSP_OFF;
                vga_dsp_config &= VGA_DSP_XCLKS_PER_QW;
                if (ATIDivide(vga_dsp_on_off, vga_dsp_config, 5, 1) > 24)
                        pll->ct.fifo_size = 32;
                else
                        pll->ct.fifo_size = 24;
        }
#endif
        /* Exit if the user does not want us to tamper with the clock
        rates of her chip. */
        if (par->mclk_per == 0) {
                u8 mclk_fb_div, pll_ext_cntl;
                pll->ct.pll_ref_div = aty_ld_pll_ct(PLL_REF_DIV, par);
                pll_ext_cntl = aty_ld_pll_ct(PLL_EXT_CNTL, par);
                pll->ct.xclk_post_div_real = aty_postdividers[pll_ext_cntl & 0x07];
                mclk_fb_div = aty_ld_pll_ct(MCLK_FB_DIV, par);
                if (pll_ext_cntl & PLL_MFB_TIMES_4_2B)
                        mclk_fb_div <<= 1;
                pll->ct.mclk_fb_div = mclk_fb_div;
                return 0;
        }

        pll->ct.pll_ref_div = par->pll_per * 2 * 255 / par->ref_clk_per;

        /* FIXME: use the VTB/GTB /3 post divider if it's better suited */
        q = par->ref_clk_per * pll->ct.pll_ref_div * 8 /
                (pll->ct.mclk_fb_mult * par->xclk_per);

        if (q < 16*8 || q > 255*8) {
                printk(KERN_CRIT "atxfb: xclk out of range\n");
                return -EINVAL;
        } else {
                xpost_div  = (q < 128*8);
                xpost_div += (q <  64*8);
                xpost_div += (q <  32*8);
        }
        pll->ct.xclk_post_div_real = aty_postdividers[xpost_div];
        pll->ct.mclk_fb_div = q * pll->ct.xclk_post_div_real / 8;

#ifdef CONFIG_PPC
        if (machine_is(powermac)) {
                /* Override PLL_EXT_CNTL & 0x07. */
                pll->ct.xclk_post_div = xpost_div;
                pll->ct.xclk_ref_div = 1;
        }
#endif

#ifdef DEBUG
        pllmclk = (1000000 * pll->ct.mclk_fb_mult * pll->ct.mclk_fb_div) /
                        (par->ref_clk_per * pll->ct.pll_ref_div);
        printk("atyfb(%s): pllmclk=%d MHz, xclk=%d MHz\n",
                __func__, pllmclk, pllmclk / pll->ct.xclk_post_div_real);
#endif

        if (M64_HAS(SDRAM_MAGIC_PLL) && (par->ram_type >= SDRAM))
                pll->ct.pll_gen_cntl = OSC_EN;
        else
                pll->ct.pll_gen_cntl = OSC_EN | DLL_PWDN /* | FORCE_DCLK_TRI_STATE */;

        if (M64_HAS(MAGIC_POSTDIV))
                pll->ct.pll_ext_cntl = 0;
        else
                pll->ct.pll_ext_cntl = xpost_div;

        if (pll->ct.mclk_fb_mult == 4)
                pll->ct.pll_ext_cntl |= PLL_MFB_TIMES_4_2B;

        if (par->mclk_per == par->xclk_per) {
                pll->ct.pll_gen_cntl |= (xpost_div << 4); /* mclk == xclk */
        } else {
                /*
                * The chip clock is not equal to the memory clock.
                * Therefore we will use sclk to clock the chip.
                */
                pll->ct.pll_gen_cntl |= (6 << 4); /* mclk == sclk */

                q = par->ref_clk_per * pll->ct.pll_ref_div * 4 / par->mclk_per;
                if (q < 16*8 || q > 255*8) {
                        printk(KERN_CRIT "atyfb: mclk out of range\n");
                        return -EINVAL;
                } else {
                        mpost_div  = (q < 128*8);
                        mpost_div += (q <  64*8);
                        mpost_div += (q <  32*8);
                }
                sclk_post_div_real = aty_postdividers[mpost_div];
                pll->ct.sclk_fb_div = q * sclk_post_div_real / 8;
                pll->ct.spll_cntl2 = mpost_div << 4;
#ifdef DEBUG
                pllsclk = (1000000 * 2 * pll->ct.sclk_fb_div) /
                        (par->ref_clk_per * pll->ct.pll_ref_div);
                printk("atyfb(%s): use sclk, pllsclk=%d MHz, sclk=mclk=%d MHz\n",
                        __func__, pllsclk, pllsclk / sclk_post_div_real);
#endif
        }

        /* Disable the extra precision pixel clock controls since we do not use them. */
        pll->ct.ext_vpll_cntl = aty_ld_pll_ct(EXT_VPLL_CNTL, par);
        pll->ct.ext_vpll_cntl &= ~(EXT_VPLL_EN | EXT_VPLL_VGA_EN | EXT_VPLL_INSYNC);

        return 0;
}

static void aty_resume_pll_ct(const struct fb_info *info,
                              union aty_pll *pll)
{
        struct atyfb_par *par = info->par;

        if (par->mclk_per != par->xclk_per) {
                /*
                * This disables the sclk, crashes the computer as reported:
                * aty_st_pll_ct(SPLL_CNTL2, 3, info);
                *
                * So it seems the sclk must be enabled before it is used;
                * so PLL_GEN_CNTL must be programmed *after* the sclk.
                */
                aty_st_pll_ct(SCLK_FB_DIV, pll->ct.sclk_fb_div, par);
                aty_st_pll_ct(SPLL_CNTL2, pll->ct.spll_cntl2, par);
                /*
                 * SCLK has been started. Wait for the PLL to lock. 5 ms
                 * should be enough according to mach64 programmer's guide.
                 */
                mdelay(5);
        }

        aty_st_pll_ct(PLL_REF_DIV, pll->ct.pll_ref_div, par);
        aty_st_pll_ct(PLL_GEN_CNTL, pll->ct.pll_gen_cntl, par);
        aty_st_pll_ct(MCLK_FB_DIV, pll->ct.mclk_fb_div, par);
        aty_st_pll_ct(PLL_EXT_CNTL, pll->ct.pll_ext_cntl, par);
        aty_st_pll_ct(EXT_VPLL_CNTL, pll->ct.ext_vpll_cntl, par);
}

static int dummy(void)
{
        return 0;
}

const struct aty_dac_ops aty_dac_ct = {
        .set_dac        = (void *) dummy,
};

const struct aty_pll_ops aty_pll_ct = {
        .var_to_pll     = aty_var_to_pll_ct,
        .pll_to_var     = aty_pll_to_var_ct,
        .set_pll        = aty_set_pll_ct,
        .get_pll        = aty_get_pll_ct,
        .init_pll       = aty_init_pll_ct,
        .resume_pll     = aty_resume_pll_ct,
};