rcutorture: Eliminate unused ts_rem local from rcu_trace_clock_local()
[linux/fpc-iii.git] / drivers / gpu / drm / bridge / adv7511 / adv7511_drv.c
blobf75ab627811349beb55180a2c651e1c666da08a7
1 /*
2 * Analog Devices ADV7511 HDMI transmitter driver
4 * Copyright 2012 Analog Devices Inc.
6 * Licensed under the GPL-2.
7 */
9 #include <linux/device.h>
10 #include <linux/gpio/consumer.h>
11 #include <linux/module.h>
12 #include <linux/of_device.h>
13 #include <linux/slab.h>
15 #include <drm/drmP.h>
16 #include <drm/drm_atomic.h>
17 #include <drm/drm_atomic_helper.h>
18 #include <drm/drm_edid.h>
20 #include "adv7511.h"
22 /* ADI recommended values for proper operation. */
23 static const struct reg_sequence adv7511_fixed_registers[] = {
24 { 0x98, 0x03 },
25 { 0x9a, 0xe0 },
26 { 0x9c, 0x30 },
27 { 0x9d, 0x61 },
28 { 0xa2, 0xa4 },
29 { 0xa3, 0xa4 },
30 { 0xe0, 0xd0 },
31 { 0xf9, 0x00 },
32 { 0x55, 0x02 },
35 /* -----------------------------------------------------------------------------
36 * Register access
39 static const uint8_t adv7511_register_defaults[] = {
40 0x12, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, /* 00 */
41 0x00, 0x00, 0x01, 0x0e, 0xbc, 0x18, 0x01, 0x13,
42 0x25, 0x37, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, /* 10 */
43 0x46, 0x62, 0x04, 0xa8, 0x00, 0x00, 0x1c, 0x84,
44 0x1c, 0xbf, 0x04, 0xa8, 0x1e, 0x70, 0x02, 0x1e, /* 20 */
45 0x00, 0x00, 0x04, 0xa8, 0x08, 0x12, 0x1b, 0xac,
46 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, /* 30 */
47 0x00, 0x00, 0x00, 0x80, 0x00, 0x00, 0x00, 0xb0,
48 0x00, 0x50, 0x90, 0x7e, 0x79, 0x70, 0x00, 0x00, /* 40 */
49 0x00, 0xa8, 0x80, 0x00, 0x00, 0x00, 0x00, 0x00,
50 0x00, 0x00, 0x02, 0x0d, 0x00, 0x00, 0x00, 0x00, /* 50 */
51 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00,
52 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, /* 60 */
53 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00,
54 0x01, 0x0a, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, /* 70 */
55 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00,
56 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, /* 80 */
57 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00,
58 0x00, 0x00, 0x00, 0x00, 0xc0, 0x00, 0x00, 0x00, /* 90 */
59 0x0b, 0x02, 0x00, 0x18, 0x5a, 0x60, 0x00, 0x00,
60 0x00, 0x00, 0x80, 0x80, 0x08, 0x04, 0x00, 0x00, /* a0 */
61 0x00, 0x00, 0x00, 0x40, 0x00, 0x00, 0x40, 0x14,
62 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, /* b0 */
63 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00,
64 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, /* c0 */
65 0x00, 0x03, 0x00, 0x00, 0x02, 0x00, 0x01, 0x04,
66 0x30, 0xff, 0x80, 0x80, 0x80, 0x00, 0x00, 0x00, /* d0 */
67 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x10, 0x01,
68 0x80, 0x75, 0x00, 0x00, 0x60, 0x00, 0x00, 0x00, /* e0 */
69 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00,
70 0x00, 0x00, 0x00, 0x00, 0x00, 0x75, 0x11, 0x00, /* f0 */
71 0x00, 0x7c, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00,
74 static bool adv7511_register_volatile(struct device *dev, unsigned int reg)
76 switch (reg) {
77 case ADV7511_REG_CHIP_REVISION:
78 case ADV7511_REG_SPDIF_FREQ:
79 case ADV7511_REG_CTS_AUTOMATIC1:
80 case ADV7511_REG_CTS_AUTOMATIC2:
81 case ADV7511_REG_VIC_DETECTED:
82 case ADV7511_REG_VIC_SEND:
83 case ADV7511_REG_AUX_VIC_DETECTED:
84 case ADV7511_REG_STATUS:
85 case ADV7511_REG_GC(1):
86 case ADV7511_REG_INT(0):
87 case ADV7511_REG_INT(1):
88 case ADV7511_REG_PLL_STATUS:
89 case ADV7511_REG_AN(0):
90 case ADV7511_REG_AN(1):
91 case ADV7511_REG_AN(2):
92 case ADV7511_REG_AN(3):
93 case ADV7511_REG_AN(4):
94 case ADV7511_REG_AN(5):
95 case ADV7511_REG_AN(6):
96 case ADV7511_REG_AN(7):
97 case ADV7511_REG_HDCP_STATUS:
98 case ADV7511_REG_BCAPS:
99 case ADV7511_REG_BKSV(0):
100 case ADV7511_REG_BKSV(1):
101 case ADV7511_REG_BKSV(2):
102 case ADV7511_REG_BKSV(3):
103 case ADV7511_REG_BKSV(4):
104 case ADV7511_REG_DDC_STATUS:
105 case ADV7511_REG_EDID_READ_CTRL:
106 case ADV7511_REG_BSTATUS(0):
107 case ADV7511_REG_BSTATUS(1):
108 case ADV7511_REG_CHIP_ID_HIGH:
109 case ADV7511_REG_CHIP_ID_LOW:
110 return true;
113 return false;
116 static const struct regmap_config adv7511_regmap_config = {
117 .reg_bits = 8,
118 .val_bits = 8,
120 .max_register = 0xff,
121 .cache_type = REGCACHE_RBTREE,
122 .reg_defaults_raw = adv7511_register_defaults,
123 .num_reg_defaults_raw = ARRAY_SIZE(adv7511_register_defaults),
125 .volatile_reg = adv7511_register_volatile,
128 /* -----------------------------------------------------------------------------
129 * Hardware configuration
132 static void adv7511_set_colormap(struct adv7511 *adv7511, bool enable,
133 const uint16_t *coeff,
134 unsigned int scaling_factor)
136 unsigned int i;
138 regmap_update_bits(adv7511->regmap, ADV7511_REG_CSC_UPPER(1),
139 ADV7511_CSC_UPDATE_MODE, ADV7511_CSC_UPDATE_MODE);
141 if (enable) {
142 for (i = 0; i < 12; ++i) {
143 regmap_update_bits(adv7511->regmap,
144 ADV7511_REG_CSC_UPPER(i),
145 0x1f, coeff[i] >> 8);
146 regmap_write(adv7511->regmap,
147 ADV7511_REG_CSC_LOWER(i),
148 coeff[i] & 0xff);
152 if (enable)
153 regmap_update_bits(adv7511->regmap, ADV7511_REG_CSC_UPPER(0),
154 0xe0, 0x80 | (scaling_factor << 5));
155 else
156 regmap_update_bits(adv7511->regmap, ADV7511_REG_CSC_UPPER(0),
157 0x80, 0x00);
159 regmap_update_bits(adv7511->regmap, ADV7511_REG_CSC_UPPER(1),
160 ADV7511_CSC_UPDATE_MODE, 0);
163 static int adv7511_packet_enable(struct adv7511 *adv7511, unsigned int packet)
165 if (packet & 0xff)
166 regmap_update_bits(adv7511->regmap, ADV7511_REG_PACKET_ENABLE0,
167 packet, 0xff);
169 if (packet & 0xff00) {
170 packet >>= 8;
171 regmap_update_bits(adv7511->regmap, ADV7511_REG_PACKET_ENABLE1,
172 packet, 0xff);
175 return 0;
178 static int adv7511_packet_disable(struct adv7511 *adv7511, unsigned int packet)
180 if (packet & 0xff)
181 regmap_update_bits(adv7511->regmap, ADV7511_REG_PACKET_ENABLE0,
182 packet, 0x00);
184 if (packet & 0xff00) {
185 packet >>= 8;
186 regmap_update_bits(adv7511->regmap, ADV7511_REG_PACKET_ENABLE1,
187 packet, 0x00);
190 return 0;
193 /* Coefficients for adv7511 color space conversion */
194 static const uint16_t adv7511_csc_ycbcr_to_rgb[] = {
195 0x0734, 0x04ad, 0x0000, 0x1c1b,
196 0x1ddc, 0x04ad, 0x1f24, 0x0135,
197 0x0000, 0x04ad, 0x087c, 0x1b77,
200 static void adv7511_set_config_csc(struct adv7511 *adv7511,
201 struct drm_connector *connector,
202 bool rgb)
204 struct adv7511_video_config config;
205 bool output_format_422, output_format_ycbcr;
206 unsigned int mode;
207 uint8_t infoframe[17];
209 if (adv7511->edid)
210 config.hdmi_mode = drm_detect_hdmi_monitor(adv7511->edid);
211 else
212 config.hdmi_mode = false;
214 hdmi_avi_infoframe_init(&config.avi_infoframe);
216 config.avi_infoframe.scan_mode = HDMI_SCAN_MODE_UNDERSCAN;
218 if (rgb) {
219 config.csc_enable = false;
220 config.avi_infoframe.colorspace = HDMI_COLORSPACE_RGB;
221 } else {
222 config.csc_scaling_factor = ADV7511_CSC_SCALING_4;
223 config.csc_coefficents = adv7511_csc_ycbcr_to_rgb;
225 if ((connector->display_info.color_formats &
226 DRM_COLOR_FORMAT_YCRCB422) &&
227 config.hdmi_mode) {
228 config.csc_enable = false;
229 config.avi_infoframe.colorspace =
230 HDMI_COLORSPACE_YUV422;
231 } else {
232 config.csc_enable = true;
233 config.avi_infoframe.colorspace = HDMI_COLORSPACE_RGB;
237 if (config.hdmi_mode) {
238 mode = ADV7511_HDMI_CFG_MODE_HDMI;
240 switch (config.avi_infoframe.colorspace) {
241 case HDMI_COLORSPACE_YUV444:
242 output_format_422 = false;
243 output_format_ycbcr = true;
244 break;
245 case HDMI_COLORSPACE_YUV422:
246 output_format_422 = true;
247 output_format_ycbcr = true;
248 break;
249 default:
250 output_format_422 = false;
251 output_format_ycbcr = false;
252 break;
254 } else {
255 mode = ADV7511_HDMI_CFG_MODE_DVI;
256 output_format_422 = false;
257 output_format_ycbcr = false;
260 adv7511_packet_disable(adv7511, ADV7511_PACKET_ENABLE_AVI_INFOFRAME);
262 adv7511_set_colormap(adv7511, config.csc_enable,
263 config.csc_coefficents,
264 config.csc_scaling_factor);
266 regmap_update_bits(adv7511->regmap, ADV7511_REG_VIDEO_INPUT_CFG1, 0x81,
267 (output_format_422 << 7) | output_format_ycbcr);
269 regmap_update_bits(adv7511->regmap, ADV7511_REG_HDCP_HDMI_CFG,
270 ADV7511_HDMI_CFG_MODE_MASK, mode);
272 hdmi_avi_infoframe_pack(&config.avi_infoframe, infoframe,
273 sizeof(infoframe));
275 /* The AVI infoframe id is not configurable */
276 regmap_bulk_write(adv7511->regmap, ADV7511_REG_AVI_INFOFRAME_VERSION,
277 infoframe + 1, sizeof(infoframe) - 1);
279 adv7511_packet_enable(adv7511, ADV7511_PACKET_ENABLE_AVI_INFOFRAME);
282 static void adv7511_set_link_config(struct adv7511 *adv7511,
283 const struct adv7511_link_config *config)
286 * The input style values documented in the datasheet don't match the
287 * hardware register field values :-(
289 static const unsigned int input_styles[4] = { 0, 2, 1, 3 };
291 unsigned int clock_delay;
292 unsigned int color_depth;
293 unsigned int input_id;
295 clock_delay = (config->clock_delay + 1200) / 400;
296 color_depth = config->input_color_depth == 8 ? 3
297 : (config->input_color_depth == 10 ? 1 : 2);
299 /* TODO Support input ID 6 */
300 if (config->input_colorspace != HDMI_COLORSPACE_YUV422)
301 input_id = config->input_clock == ADV7511_INPUT_CLOCK_DDR
302 ? 5 : 0;
303 else if (config->input_clock == ADV7511_INPUT_CLOCK_DDR)
304 input_id = config->embedded_sync ? 8 : 7;
305 else if (config->input_clock == ADV7511_INPUT_CLOCK_2X)
306 input_id = config->embedded_sync ? 4 : 3;
307 else
308 input_id = config->embedded_sync ? 2 : 1;
310 regmap_update_bits(adv7511->regmap, ADV7511_REG_I2C_FREQ_ID_CFG, 0xf,
311 input_id);
312 regmap_update_bits(adv7511->regmap, ADV7511_REG_VIDEO_INPUT_CFG1, 0x7e,
313 (color_depth << 4) |
314 (input_styles[config->input_style] << 2));
315 regmap_write(adv7511->regmap, ADV7511_REG_VIDEO_INPUT_CFG2,
316 config->input_justification << 3);
317 regmap_write(adv7511->regmap, ADV7511_REG_TIMING_GEN_SEQ,
318 config->sync_pulse << 2);
320 regmap_write(adv7511->regmap, 0xba, clock_delay << 5);
322 adv7511->embedded_sync = config->embedded_sync;
323 adv7511->hsync_polarity = config->hsync_polarity;
324 adv7511->vsync_polarity = config->vsync_polarity;
325 adv7511->rgb = config->input_colorspace == HDMI_COLORSPACE_RGB;
328 static void __adv7511_power_on(struct adv7511 *adv7511)
330 adv7511->current_edid_segment = -1;
332 regmap_update_bits(adv7511->regmap, ADV7511_REG_POWER,
333 ADV7511_POWER_POWER_DOWN, 0);
334 if (adv7511->i2c_main->irq) {
336 * Documentation says the INT_ENABLE registers are reset in
337 * POWER_DOWN mode. My 7511w preserved the bits, however.
338 * Still, let's be safe and stick to the documentation.
340 regmap_write(adv7511->regmap, ADV7511_REG_INT_ENABLE(0),
341 ADV7511_INT0_EDID_READY | ADV7511_INT0_HPD);
342 regmap_write(adv7511->regmap, ADV7511_REG_INT_ENABLE(1),
343 ADV7511_INT1_DDC_ERROR);
347 * Per spec it is allowed to pulse the HPD signal to indicate that the
348 * EDID information has changed. Some monitors do this when they wakeup
349 * from standby or are enabled. When the HPD goes low the adv7511 is
350 * reset and the outputs are disabled which might cause the monitor to
351 * go to standby again. To avoid this we ignore the HPD pin for the
352 * first few seconds after enabling the output.
354 regmap_update_bits(adv7511->regmap, ADV7511_REG_POWER2,
355 ADV7511_REG_POWER2_HPD_SRC_MASK,
356 ADV7511_REG_POWER2_HPD_SRC_NONE);
359 static void adv7511_power_on(struct adv7511 *adv7511)
361 __adv7511_power_on(adv7511);
364 * Most of the registers are reset during power down or when HPD is low.
366 regcache_sync(adv7511->regmap);
368 if (adv7511->type == ADV7533)
369 adv7533_dsi_power_on(adv7511);
370 adv7511->powered = true;
373 static void __adv7511_power_off(struct adv7511 *adv7511)
375 /* TODO: setup additional power down modes */
376 regmap_update_bits(adv7511->regmap, ADV7511_REG_POWER,
377 ADV7511_POWER_POWER_DOWN,
378 ADV7511_POWER_POWER_DOWN);
379 regcache_mark_dirty(adv7511->regmap);
382 static void adv7511_power_off(struct adv7511 *adv7511)
384 __adv7511_power_off(adv7511);
385 if (adv7511->type == ADV7533)
386 adv7533_dsi_power_off(adv7511);
387 adv7511->powered = false;
390 /* -----------------------------------------------------------------------------
391 * Interrupt and hotplug detection
394 static bool adv7511_hpd(struct adv7511 *adv7511)
396 unsigned int irq0;
397 int ret;
399 ret = regmap_read(adv7511->regmap, ADV7511_REG_INT(0), &irq0);
400 if (ret < 0)
401 return false;
403 if (irq0 & ADV7511_INT0_HPD) {
404 regmap_write(adv7511->regmap, ADV7511_REG_INT(0),
405 ADV7511_INT0_HPD);
406 return true;
409 return false;
412 static void adv7511_hpd_work(struct work_struct *work)
414 struct adv7511 *adv7511 = container_of(work, struct adv7511, hpd_work);
415 enum drm_connector_status status;
416 unsigned int val;
417 int ret;
419 ret = regmap_read(adv7511->regmap, ADV7511_REG_STATUS, &val);
420 if (ret < 0)
421 status = connector_status_disconnected;
422 else if (val & ADV7511_STATUS_HPD)
423 status = connector_status_connected;
424 else
425 status = connector_status_disconnected;
427 if (adv7511->connector.status != status) {
428 adv7511->connector.status = status;
429 drm_kms_helper_hotplug_event(adv7511->connector.dev);
433 static int adv7511_irq_process(struct adv7511 *adv7511, bool process_hpd)
435 unsigned int irq0, irq1;
436 int ret;
438 ret = regmap_read(adv7511->regmap, ADV7511_REG_INT(0), &irq0);
439 if (ret < 0)
440 return ret;
442 ret = regmap_read(adv7511->regmap, ADV7511_REG_INT(1), &irq1);
443 if (ret < 0)
444 return ret;
446 regmap_write(adv7511->regmap, ADV7511_REG_INT(0), irq0);
447 regmap_write(adv7511->regmap, ADV7511_REG_INT(1), irq1);
449 if (process_hpd && irq0 & ADV7511_INT0_HPD && adv7511->bridge.encoder)
450 schedule_work(&adv7511->hpd_work);
452 if (irq0 & ADV7511_INT0_EDID_READY || irq1 & ADV7511_INT1_DDC_ERROR) {
453 adv7511->edid_read = true;
455 if (adv7511->i2c_main->irq)
456 wake_up_all(&adv7511->wq);
459 return 0;
462 static irqreturn_t adv7511_irq_handler(int irq, void *devid)
464 struct adv7511 *adv7511 = devid;
465 int ret;
467 ret = adv7511_irq_process(adv7511, true);
468 return ret < 0 ? IRQ_NONE : IRQ_HANDLED;
471 /* -----------------------------------------------------------------------------
472 * EDID retrieval
475 static int adv7511_wait_for_edid(struct adv7511 *adv7511, int timeout)
477 int ret;
479 if (adv7511->i2c_main->irq) {
480 ret = wait_event_interruptible_timeout(adv7511->wq,
481 adv7511->edid_read, msecs_to_jiffies(timeout));
482 } else {
483 for (; timeout > 0; timeout -= 25) {
484 ret = adv7511_irq_process(adv7511, false);
485 if (ret < 0)
486 break;
488 if (adv7511->edid_read)
489 break;
491 msleep(25);
495 return adv7511->edid_read ? 0 : -EIO;
498 static int adv7511_get_edid_block(void *data, u8 *buf, unsigned int block,
499 size_t len)
501 struct adv7511 *adv7511 = data;
502 struct i2c_msg xfer[2];
503 uint8_t offset;
504 unsigned int i;
505 int ret;
507 if (len > 128)
508 return -EINVAL;
510 if (adv7511->current_edid_segment != block / 2) {
511 unsigned int status;
513 ret = regmap_read(adv7511->regmap, ADV7511_REG_DDC_STATUS,
514 &status);
515 if (ret < 0)
516 return ret;
518 if (status != 2) {
519 adv7511->edid_read = false;
520 regmap_write(adv7511->regmap, ADV7511_REG_EDID_SEGMENT,
521 block);
522 ret = adv7511_wait_for_edid(adv7511, 200);
523 if (ret < 0)
524 return ret;
527 /* Break this apart, hopefully more I2C controllers will
528 * support 64 byte transfers than 256 byte transfers
531 xfer[0].addr = adv7511->i2c_edid->addr;
532 xfer[0].flags = 0;
533 xfer[0].len = 1;
534 xfer[0].buf = &offset;
535 xfer[1].addr = adv7511->i2c_edid->addr;
536 xfer[1].flags = I2C_M_RD;
537 xfer[1].len = 64;
538 xfer[1].buf = adv7511->edid_buf;
540 offset = 0;
542 for (i = 0; i < 4; ++i) {
543 ret = i2c_transfer(adv7511->i2c_edid->adapter, xfer,
544 ARRAY_SIZE(xfer));
545 if (ret < 0)
546 return ret;
547 else if (ret != 2)
548 return -EIO;
550 xfer[1].buf += 64;
551 offset += 64;
554 adv7511->current_edid_segment = block / 2;
557 if (block % 2 == 0)
558 memcpy(buf, adv7511->edid_buf, len);
559 else
560 memcpy(buf, adv7511->edid_buf + 128, len);
562 return 0;
565 /* -----------------------------------------------------------------------------
566 * ADV75xx helpers
569 static int adv7511_get_modes(struct adv7511 *adv7511,
570 struct drm_connector *connector)
572 struct edid *edid;
573 unsigned int count;
575 /* Reading the EDID only works if the device is powered */
576 if (!adv7511->powered) {
577 unsigned int edid_i2c_addr =
578 (adv7511->i2c_main->addr << 1) + 4;
580 __adv7511_power_on(adv7511);
582 /* Reset the EDID_I2C_ADDR register as it might be cleared */
583 regmap_write(adv7511->regmap, ADV7511_REG_EDID_I2C_ADDR,
584 edid_i2c_addr);
587 edid = drm_do_get_edid(connector, adv7511_get_edid_block, adv7511);
589 if (!adv7511->powered)
590 __adv7511_power_off(adv7511);
592 kfree(adv7511->edid);
593 adv7511->edid = edid;
594 if (!edid)
595 return 0;
597 drm_mode_connector_update_edid_property(connector, edid);
598 count = drm_add_edid_modes(connector, edid);
600 adv7511_set_config_csc(adv7511, connector, adv7511->rgb);
602 return count;
605 static enum drm_connector_status
606 adv7511_detect(struct adv7511 *adv7511, struct drm_connector *connector)
608 enum drm_connector_status status;
609 unsigned int val;
610 bool hpd;
611 int ret;
613 ret = regmap_read(adv7511->regmap, ADV7511_REG_STATUS, &val);
614 if (ret < 0)
615 return connector_status_disconnected;
617 if (val & ADV7511_STATUS_HPD)
618 status = connector_status_connected;
619 else
620 status = connector_status_disconnected;
622 hpd = adv7511_hpd(adv7511);
624 /* The chip resets itself when the cable is disconnected, so in case
625 * there is a pending HPD interrupt and the cable is connected there was
626 * at least one transition from disconnected to connected and the chip
627 * has to be reinitialized. */
628 if (status == connector_status_connected && hpd && adv7511->powered) {
629 regcache_mark_dirty(adv7511->regmap);
630 adv7511_power_on(adv7511);
631 adv7511_get_modes(adv7511, connector);
632 if (adv7511->status == connector_status_connected)
633 status = connector_status_disconnected;
634 } else {
635 /* Renable HPD sensing */
636 regmap_update_bits(adv7511->regmap, ADV7511_REG_POWER2,
637 ADV7511_REG_POWER2_HPD_SRC_MASK,
638 ADV7511_REG_POWER2_HPD_SRC_BOTH);
641 adv7511->status = status;
642 return status;
645 static int adv7511_mode_valid(struct adv7511 *adv7511,
646 struct drm_display_mode *mode)
648 if (mode->clock > 165000)
649 return MODE_CLOCK_HIGH;
651 return MODE_OK;
654 static void adv7511_mode_set(struct adv7511 *adv7511,
655 struct drm_display_mode *mode,
656 struct drm_display_mode *adj_mode)
658 unsigned int low_refresh_rate;
659 unsigned int hsync_polarity = 0;
660 unsigned int vsync_polarity = 0;
662 if (adv7511->embedded_sync) {
663 unsigned int hsync_offset, hsync_len;
664 unsigned int vsync_offset, vsync_len;
666 hsync_offset = adj_mode->crtc_hsync_start -
667 adj_mode->crtc_hdisplay;
668 vsync_offset = adj_mode->crtc_vsync_start -
669 adj_mode->crtc_vdisplay;
670 hsync_len = adj_mode->crtc_hsync_end -
671 adj_mode->crtc_hsync_start;
672 vsync_len = adj_mode->crtc_vsync_end -
673 adj_mode->crtc_vsync_start;
675 /* The hardware vsync generator has a off-by-one bug */
676 vsync_offset += 1;
678 regmap_write(adv7511->regmap, ADV7511_REG_HSYNC_PLACEMENT_MSB,
679 ((hsync_offset >> 10) & 0x7) << 5);
680 regmap_write(adv7511->regmap, ADV7511_REG_SYNC_DECODER(0),
681 (hsync_offset >> 2) & 0xff);
682 regmap_write(adv7511->regmap, ADV7511_REG_SYNC_DECODER(1),
683 ((hsync_offset & 0x3) << 6) |
684 ((hsync_len >> 4) & 0x3f));
685 regmap_write(adv7511->regmap, ADV7511_REG_SYNC_DECODER(2),
686 ((hsync_len & 0xf) << 4) |
687 ((vsync_offset >> 6) & 0xf));
688 regmap_write(adv7511->regmap, ADV7511_REG_SYNC_DECODER(3),
689 ((vsync_offset & 0x3f) << 2) |
690 ((vsync_len >> 8) & 0x3));
691 regmap_write(adv7511->regmap, ADV7511_REG_SYNC_DECODER(4),
692 vsync_len & 0xff);
694 hsync_polarity = !(adj_mode->flags & DRM_MODE_FLAG_PHSYNC);
695 vsync_polarity = !(adj_mode->flags & DRM_MODE_FLAG_PVSYNC);
696 } else {
697 enum adv7511_sync_polarity mode_hsync_polarity;
698 enum adv7511_sync_polarity mode_vsync_polarity;
701 * If the input signal is always low or always high we want to
702 * invert or let it passthrough depending on the polarity of the
703 * current mode.
705 if (adj_mode->flags & DRM_MODE_FLAG_NHSYNC)
706 mode_hsync_polarity = ADV7511_SYNC_POLARITY_LOW;
707 else
708 mode_hsync_polarity = ADV7511_SYNC_POLARITY_HIGH;
710 if (adj_mode->flags & DRM_MODE_FLAG_NVSYNC)
711 mode_vsync_polarity = ADV7511_SYNC_POLARITY_LOW;
712 else
713 mode_vsync_polarity = ADV7511_SYNC_POLARITY_HIGH;
715 if (adv7511->hsync_polarity != mode_hsync_polarity &&
716 adv7511->hsync_polarity !=
717 ADV7511_SYNC_POLARITY_PASSTHROUGH)
718 hsync_polarity = 1;
720 if (adv7511->vsync_polarity != mode_vsync_polarity &&
721 adv7511->vsync_polarity !=
722 ADV7511_SYNC_POLARITY_PASSTHROUGH)
723 vsync_polarity = 1;
726 if (mode->vrefresh <= 24000)
727 low_refresh_rate = ADV7511_LOW_REFRESH_RATE_24HZ;
728 else if (mode->vrefresh <= 25000)
729 low_refresh_rate = ADV7511_LOW_REFRESH_RATE_25HZ;
730 else if (mode->vrefresh <= 30000)
731 low_refresh_rate = ADV7511_LOW_REFRESH_RATE_30HZ;
732 else
733 low_refresh_rate = ADV7511_LOW_REFRESH_RATE_NONE;
735 regmap_update_bits(adv7511->regmap, 0xfb,
736 0x6, low_refresh_rate << 1);
737 regmap_update_bits(adv7511->regmap, 0x17,
738 0x60, (vsync_polarity << 6) | (hsync_polarity << 5));
740 if (adv7511->type == ADV7533)
741 adv7533_mode_set(adv7511, adj_mode);
743 drm_mode_copy(&adv7511->curr_mode, adj_mode);
746 * TODO Test first order 4:2:2 to 4:4:4 up conversion method, which is
747 * supposed to give better results.
750 adv7511->f_tmds = mode->clock;
753 /* Connector funcs */
754 static struct adv7511 *connector_to_adv7511(struct drm_connector *connector)
756 return container_of(connector, struct adv7511, connector);
759 static int adv7511_connector_get_modes(struct drm_connector *connector)
761 struct adv7511 *adv = connector_to_adv7511(connector);
763 return adv7511_get_modes(adv, connector);
766 static enum drm_mode_status
767 adv7511_connector_mode_valid(struct drm_connector *connector,
768 struct drm_display_mode *mode)
770 struct adv7511 *adv = connector_to_adv7511(connector);
772 return adv7511_mode_valid(adv, mode);
775 static struct drm_connector_helper_funcs adv7511_connector_helper_funcs = {
776 .get_modes = adv7511_connector_get_modes,
777 .mode_valid = adv7511_connector_mode_valid,
780 static enum drm_connector_status
781 adv7511_connector_detect(struct drm_connector *connector, bool force)
783 struct adv7511 *adv = connector_to_adv7511(connector);
785 return adv7511_detect(adv, connector);
788 static struct drm_connector_funcs adv7511_connector_funcs = {
789 .dpms = drm_atomic_helper_connector_dpms,
790 .fill_modes = drm_helper_probe_single_connector_modes,
791 .detect = adv7511_connector_detect,
792 .destroy = drm_connector_cleanup,
793 .reset = drm_atomic_helper_connector_reset,
794 .atomic_duplicate_state = drm_atomic_helper_connector_duplicate_state,
795 .atomic_destroy_state = drm_atomic_helper_connector_destroy_state,
798 /* Bridge funcs */
799 static struct adv7511 *bridge_to_adv7511(struct drm_bridge *bridge)
801 return container_of(bridge, struct adv7511, bridge);
804 static void adv7511_bridge_enable(struct drm_bridge *bridge)
806 struct adv7511 *adv = bridge_to_adv7511(bridge);
808 adv7511_power_on(adv);
811 static void adv7511_bridge_disable(struct drm_bridge *bridge)
813 struct adv7511 *adv = bridge_to_adv7511(bridge);
815 adv7511_power_off(adv);
818 static void adv7511_bridge_mode_set(struct drm_bridge *bridge,
819 struct drm_display_mode *mode,
820 struct drm_display_mode *adj_mode)
822 struct adv7511 *adv = bridge_to_adv7511(bridge);
824 adv7511_mode_set(adv, mode, adj_mode);
827 static int adv7511_bridge_attach(struct drm_bridge *bridge)
829 struct adv7511 *adv = bridge_to_adv7511(bridge);
830 int ret;
832 if (!bridge->encoder) {
833 DRM_ERROR("Parent encoder object not found");
834 return -ENODEV;
837 adv->connector.polled = DRM_CONNECTOR_POLL_HPD;
839 ret = drm_connector_init(bridge->dev, &adv->connector,
840 &adv7511_connector_funcs,
841 DRM_MODE_CONNECTOR_HDMIA);
842 if (ret) {
843 DRM_ERROR("Failed to initialize connector with drm\n");
844 return ret;
846 drm_connector_helper_add(&adv->connector,
847 &adv7511_connector_helper_funcs);
848 drm_mode_connector_attach_encoder(&adv->connector, bridge->encoder);
850 if (adv->type == ADV7533)
851 ret = adv7533_attach_dsi(adv);
853 if (adv->i2c_main->irq)
854 regmap_write(adv->regmap, ADV7511_REG_INT_ENABLE(0),
855 ADV7511_INT0_HPD);
857 return ret;
860 static struct drm_bridge_funcs adv7511_bridge_funcs = {
861 .enable = adv7511_bridge_enable,
862 .disable = adv7511_bridge_disable,
863 .mode_set = adv7511_bridge_mode_set,
864 .attach = adv7511_bridge_attach,
867 /* -----------------------------------------------------------------------------
868 * Probe & remove
871 static const char * const adv7511_supply_names[] = {
872 "avdd",
873 "dvdd",
874 "pvdd",
875 "bgvdd",
876 "dvdd-3v",
879 static const char * const adv7533_supply_names[] = {
880 "avdd",
881 "dvdd",
882 "pvdd",
883 "a2vdd",
884 "v3p3",
885 "v1p2",
888 static int adv7511_init_regulators(struct adv7511 *adv)
890 struct device *dev = &adv->i2c_main->dev;
891 const char * const *supply_names;
892 unsigned int i;
893 int ret;
895 if (adv->type == ADV7511) {
896 supply_names = adv7511_supply_names;
897 adv->num_supplies = ARRAY_SIZE(adv7511_supply_names);
898 } else {
899 supply_names = adv7533_supply_names;
900 adv->num_supplies = ARRAY_SIZE(adv7533_supply_names);
903 adv->supplies = devm_kcalloc(dev, adv->num_supplies,
904 sizeof(*adv->supplies), GFP_KERNEL);
905 if (!adv->supplies)
906 return -ENOMEM;
908 for (i = 0; i < adv->num_supplies; i++)
909 adv->supplies[i].supply = supply_names[i];
911 ret = devm_regulator_bulk_get(dev, adv->num_supplies, adv->supplies);
912 if (ret)
913 return ret;
915 return regulator_bulk_enable(adv->num_supplies, adv->supplies);
918 static void adv7511_uninit_regulators(struct adv7511 *adv)
920 regulator_bulk_disable(adv->num_supplies, adv->supplies);
923 static int adv7511_parse_dt(struct device_node *np,
924 struct adv7511_link_config *config)
926 const char *str;
927 int ret;
929 of_property_read_u32(np, "adi,input-depth", &config->input_color_depth);
930 if (config->input_color_depth != 8 && config->input_color_depth != 10 &&
931 config->input_color_depth != 12)
932 return -EINVAL;
934 ret = of_property_read_string(np, "adi,input-colorspace", &str);
935 if (ret < 0)
936 return ret;
938 if (!strcmp(str, "rgb"))
939 config->input_colorspace = HDMI_COLORSPACE_RGB;
940 else if (!strcmp(str, "yuv422"))
941 config->input_colorspace = HDMI_COLORSPACE_YUV422;
942 else if (!strcmp(str, "yuv444"))
943 config->input_colorspace = HDMI_COLORSPACE_YUV444;
944 else
945 return -EINVAL;
947 ret = of_property_read_string(np, "adi,input-clock", &str);
948 if (ret < 0)
949 return ret;
951 if (!strcmp(str, "1x"))
952 config->input_clock = ADV7511_INPUT_CLOCK_1X;
953 else if (!strcmp(str, "2x"))
954 config->input_clock = ADV7511_INPUT_CLOCK_2X;
955 else if (!strcmp(str, "ddr"))
956 config->input_clock = ADV7511_INPUT_CLOCK_DDR;
957 else
958 return -EINVAL;
960 if (config->input_colorspace == HDMI_COLORSPACE_YUV422 ||
961 config->input_clock != ADV7511_INPUT_CLOCK_1X) {
962 ret = of_property_read_u32(np, "adi,input-style",
963 &config->input_style);
964 if (ret)
965 return ret;
967 if (config->input_style < 1 || config->input_style > 3)
968 return -EINVAL;
970 ret = of_property_read_string(np, "adi,input-justification",
971 &str);
972 if (ret < 0)
973 return ret;
975 if (!strcmp(str, "left"))
976 config->input_justification =
977 ADV7511_INPUT_JUSTIFICATION_LEFT;
978 else if (!strcmp(str, "evenly"))
979 config->input_justification =
980 ADV7511_INPUT_JUSTIFICATION_EVENLY;
981 else if (!strcmp(str, "right"))
982 config->input_justification =
983 ADV7511_INPUT_JUSTIFICATION_RIGHT;
984 else
985 return -EINVAL;
987 } else {
988 config->input_style = 1;
989 config->input_justification = ADV7511_INPUT_JUSTIFICATION_LEFT;
992 of_property_read_u32(np, "adi,clock-delay", &config->clock_delay);
993 if (config->clock_delay < -1200 || config->clock_delay > 1600)
994 return -EINVAL;
996 config->embedded_sync = of_property_read_bool(np, "adi,embedded-sync");
998 /* Hardcode the sync pulse configurations for now. */
999 config->sync_pulse = ADV7511_INPUT_SYNC_PULSE_NONE;
1000 config->vsync_polarity = ADV7511_SYNC_POLARITY_PASSTHROUGH;
1001 config->hsync_polarity = ADV7511_SYNC_POLARITY_PASSTHROUGH;
1003 return 0;
1006 static int adv7511_probe(struct i2c_client *i2c, const struct i2c_device_id *id)
1008 struct adv7511_link_config link_config;
1009 struct adv7511 *adv7511;
1010 struct device *dev = &i2c->dev;
1011 unsigned int main_i2c_addr = i2c->addr << 1;
1012 unsigned int edid_i2c_addr = main_i2c_addr + 4;
1013 unsigned int val;
1014 int ret;
1016 if (!dev->of_node)
1017 return -EINVAL;
1019 adv7511 = devm_kzalloc(dev, sizeof(*adv7511), GFP_KERNEL);
1020 if (!adv7511)
1021 return -ENOMEM;
1023 adv7511->i2c_main = i2c;
1024 adv7511->powered = false;
1025 adv7511->status = connector_status_disconnected;
1027 if (dev->of_node)
1028 adv7511->type = (enum adv7511_type)of_device_get_match_data(dev);
1029 else
1030 adv7511->type = id->driver_data;
1032 memset(&link_config, 0, sizeof(link_config));
1034 if (adv7511->type == ADV7511)
1035 ret = adv7511_parse_dt(dev->of_node, &link_config);
1036 else
1037 ret = adv7533_parse_dt(dev->of_node, adv7511);
1038 if (ret)
1039 return ret;
1041 ret = adv7511_init_regulators(adv7511);
1042 if (ret) {
1043 dev_err(dev, "failed to init regulators\n");
1044 return ret;
1048 * The power down GPIO is optional. If present, toggle it from active to
1049 * inactive to wake up the encoder.
1051 adv7511->gpio_pd = devm_gpiod_get_optional(dev, "pd", GPIOD_OUT_HIGH);
1052 if (IS_ERR(adv7511->gpio_pd)) {
1053 ret = PTR_ERR(adv7511->gpio_pd);
1054 goto uninit_regulators;
1057 if (adv7511->gpio_pd) {
1058 mdelay(5);
1059 gpiod_set_value_cansleep(adv7511->gpio_pd, 0);
1062 adv7511->regmap = devm_regmap_init_i2c(i2c, &adv7511_regmap_config);
1063 if (IS_ERR(adv7511->regmap)) {
1064 ret = PTR_ERR(adv7511->regmap);
1065 goto uninit_regulators;
1068 ret = regmap_read(adv7511->regmap, ADV7511_REG_CHIP_REVISION, &val);
1069 if (ret)
1070 goto uninit_regulators;
1071 dev_dbg(dev, "Rev. %d\n", val);
1073 if (adv7511->type == ADV7511)
1074 ret = regmap_register_patch(adv7511->regmap,
1075 adv7511_fixed_registers,
1076 ARRAY_SIZE(adv7511_fixed_registers));
1077 else
1078 ret = adv7533_patch_registers(adv7511);
1079 if (ret)
1080 goto uninit_regulators;
1082 regmap_write(adv7511->regmap, ADV7511_REG_EDID_I2C_ADDR, edid_i2c_addr);
1083 regmap_write(adv7511->regmap, ADV7511_REG_PACKET_I2C_ADDR,
1084 main_i2c_addr - 0xa);
1085 regmap_write(adv7511->regmap, ADV7511_REG_CEC_I2C_ADDR,
1086 main_i2c_addr - 2);
1088 adv7511_packet_disable(adv7511, 0xffff);
1090 adv7511->i2c_edid = i2c_new_dummy(i2c->adapter, edid_i2c_addr >> 1);
1091 if (!adv7511->i2c_edid) {
1092 ret = -ENOMEM;
1093 goto uninit_regulators;
1096 if (adv7511->type == ADV7533) {
1097 ret = adv7533_init_cec(adv7511);
1098 if (ret)
1099 goto err_i2c_unregister_edid;
1102 INIT_WORK(&adv7511->hpd_work, adv7511_hpd_work);
1104 if (i2c->irq) {
1105 init_waitqueue_head(&adv7511->wq);
1107 ret = devm_request_threaded_irq(dev, i2c->irq, NULL,
1108 adv7511_irq_handler,
1109 IRQF_ONESHOT, dev_name(dev),
1110 adv7511);
1111 if (ret)
1112 goto err_unregister_cec;
1115 /* CEC is unused for now */
1116 regmap_write(adv7511->regmap, ADV7511_REG_CEC_CTRL,
1117 ADV7511_CEC_CTRL_POWER_DOWN);
1119 adv7511_power_off(adv7511);
1121 i2c_set_clientdata(i2c, adv7511);
1123 if (adv7511->type == ADV7511)
1124 adv7511_set_link_config(adv7511, &link_config);
1126 adv7511->bridge.funcs = &adv7511_bridge_funcs;
1127 adv7511->bridge.of_node = dev->of_node;
1129 ret = drm_bridge_add(&adv7511->bridge);
1130 if (ret) {
1131 dev_err(dev, "failed to add adv7511 bridge\n");
1132 goto err_unregister_cec;
1135 adv7511_audio_init(dev, adv7511);
1137 return 0;
1139 err_unregister_cec:
1140 adv7533_uninit_cec(adv7511);
1141 err_i2c_unregister_edid:
1142 i2c_unregister_device(adv7511->i2c_edid);
1143 uninit_regulators:
1144 adv7511_uninit_regulators(adv7511);
1146 return ret;
1149 static int adv7511_remove(struct i2c_client *i2c)
1151 struct adv7511 *adv7511 = i2c_get_clientdata(i2c);
1153 if (adv7511->type == ADV7533) {
1154 adv7533_detach_dsi(adv7511);
1155 adv7533_uninit_cec(adv7511);
1158 adv7511_uninit_regulators(adv7511);
1160 drm_bridge_remove(&adv7511->bridge);
1162 adv7511_audio_exit(adv7511);
1164 i2c_unregister_device(adv7511->i2c_edid);
1166 kfree(adv7511->edid);
1168 return 0;
1171 static const struct i2c_device_id adv7511_i2c_ids[] = {
1172 { "adv7511", ADV7511 },
1173 { "adv7511w", ADV7511 },
1174 { "adv7513", ADV7511 },
1175 #ifdef CONFIG_DRM_I2C_ADV7533
1176 { "adv7533", ADV7533 },
1177 #endif
1180 MODULE_DEVICE_TABLE(i2c, adv7511_i2c_ids);
1182 static const struct of_device_id adv7511_of_ids[] = {
1183 { .compatible = "adi,adv7511", .data = (void *)ADV7511 },
1184 { .compatible = "adi,adv7511w", .data = (void *)ADV7511 },
1185 { .compatible = "adi,adv7513", .data = (void *)ADV7511 },
1186 #ifdef CONFIG_DRM_I2C_ADV7533
1187 { .compatible = "adi,adv7533", .data = (void *)ADV7533 },
1188 #endif
1191 MODULE_DEVICE_TABLE(of, adv7511_of_ids);
1193 static struct mipi_dsi_driver adv7533_dsi_driver = {
1194 .driver.name = "adv7533",
1197 static struct i2c_driver adv7511_driver = {
1198 .driver = {
1199 .name = "adv7511",
1200 .of_match_table = adv7511_of_ids,
1202 .id_table = adv7511_i2c_ids,
1203 .probe = adv7511_probe,
1204 .remove = adv7511_remove,
1207 static int __init adv7511_init(void)
1209 if (IS_ENABLED(CONFIG_DRM_MIPI_DSI))
1210 mipi_dsi_driver_register(&adv7533_dsi_driver);
1212 return i2c_add_driver(&adv7511_driver);
1214 module_init(adv7511_init);
1216 static void __exit adv7511_exit(void)
1218 i2c_del_driver(&adv7511_driver);
1220 if (IS_ENABLED(CONFIG_DRM_MIPI_DSI))
1221 mipi_dsi_driver_unregister(&adv7533_dsi_driver);
1223 module_exit(adv7511_exit);
1225 MODULE_AUTHOR("Lars-Peter Clausen <lars@metafoo.de>");
1226 MODULE_DESCRIPTION("ADV7511 HDMI transmitter driver");
1227 MODULE_LICENSE("GPL");