Linux 3.16-rc2

[linux/fpc-iii.git] / Documentation / DocBook / drm.tmpl

<?xml version="1.0" encoding="UTF-8"?>
<!DOCTYPE book PUBLIC "-//OASIS//DTD DocBook XML V4.1.2//EN"
        "http://www.oasis-open.org/docbook/xml/4.1.2/docbookx.dtd" []>

<book id="drmDevelopersGuide">
  <bookinfo>
    <title>Linux DRM Developer's Guide</title>

    <authorgroup>
      <author>
        <firstname>Jesse</firstname>
        <surname>Barnes</surname>
        <contrib>Initial version</contrib>
        <affiliation>
          <orgname>Intel Corporation</orgname>
          <address>
            <email>jesse.barnes@intel.com</email>
          </address>
        </affiliation>
      </author>
      <author>
        <firstname>Laurent</firstname>
        <surname>Pinchart</surname>
        <contrib>Driver internals</contrib>
        <affiliation>
          <orgname>Ideas on board SPRL</orgname>
          <address>
            <email>laurent.pinchart@ideasonboard.com</email>
          </address>
        </affiliation>
      </author>
      <author>
        <firstname>Daniel</firstname>
        <surname>Vetter</surname>
        <contrib>Contributions all over the place</contrib>
        <affiliation>
          <orgname>Intel Corporation</orgname>
          <address>
            <email>daniel.vetter@ffwll.ch</email>
          </address>
        </affiliation>
      </author>
    </authorgroup>

    <copyright>
      <year>2008-2009</year>
      <year>2013-2014</year>
      <holder>Intel Corporation</holder>
    </copyright>
    <copyright>
      <year>2012</year>
      <holder>Laurent Pinchart</holder>
    </copyright>

    <legalnotice>
      <para>
        The contents of this file may be used under the terms of the GNU
        General Public License version 2 (the "GPL") as distributed in
        the kernel source COPYING file.
      </para>
    </legalnotice>

    <revhistory>
      <!-- Put document revisions here, newest first. -->
      <revision>
        <revnumber>1.0</revnumber>
        <date>2012-07-13</date>
        <authorinitials>LP</authorinitials>
        <revremark>Added extensive documentation about driver internals.
        </revremark>
      </revision>
    </revhistory>
  </bookinfo>

<toc></toc>

<part id="drmCore">
  <title>DRM Core</title>
  <partintro>
    <para>
      This first part of the DRM Developer's Guide documents core DRM code,
      helper libraries for writing drivers and generic userspace interfaces
      exposed by DRM drivers.
    </para>
  </partintro>

  <chapter id="drmIntroduction">
    <title>Introduction</title>
    <para>
      The Linux DRM layer contains code intended to support the needs
      of complex graphics devices, usually containing programmable
      pipelines well suited to 3D graphics acceleration.  Graphics
      drivers in the kernel may make use of DRM functions to make
      tasks like memory management, interrupt handling and DMA easier,
      and provide a uniform interface to applications.
    </para>
    <para>
      A note on versions: this guide covers features found in the DRM
      tree, including the TTM memory manager, output configuration and
      mode setting, and the new vblank internals, in addition to all
      the regular features found in current kernels.
    </para>
    <para>
      [Insert diagram of typical DRM stack here]
    </para>
  </chapter>

  <!-- Internals -->

  <chapter id="drmInternals">
    <title>DRM Internals</title>
    <para>
      This chapter documents DRM internals relevant to driver authors
      and developers working to add support for the latest features to
      existing drivers.
    </para>
    <para>
      First, we go over some typical driver initialization
      requirements, like setting up command buffers, creating an
      initial output configuration, and initializing core services.
      Subsequent sections cover core internals in more detail,
      providing implementation notes and examples.
    </para>
    <para>
      The DRM layer provides several services to graphics drivers,
      many of them driven by the application interfaces it provides
      through libdrm, the library that wraps most of the DRM ioctls.
      These include vblank event handling, memory
      management, output management, framebuffer management, command
      submission &amp; fencing, suspend/resume support, and DMA
      services.
    </para>

  <!-- Internals: driver init -->

  <sect1>
    <title>Driver Initialization</title>
    <para>
      At the core of every DRM driver is a <structname>drm_driver</structname>
      structure. Drivers typically statically initialize a drm_driver structure,
      and then pass it to one of the <function>drm_*_init()</function> functions
      to register it with the DRM subsystem.
    </para>
    <para>
      Newer drivers that no longer require a <structname>drm_bus</structname>
      structure can alternatively use the low-level device initialization and
      registration functions such as <function>drm_dev_alloc()</function> and
      <function>drm_dev_register()</function> directly.
    </para>
    <para>
      The <structname>drm_driver</structname> structure contains static
      information that describes the driver and features it supports, and
      pointers to methods that the DRM core will call to implement the DRM API.
      We will first go through the <structname>drm_driver</structname> static
      information fields, and will then describe individual operations in
      details as they get used in later sections.
    </para>
    <sect2>
      <title>Driver Information</title>
      <sect3>
        <title>Driver Features</title>
        <para>
          Drivers inform the DRM core about their requirements and supported
          features by setting appropriate flags in the
          <structfield>driver_features</structfield> field. Since those flags
          influence the DRM core behaviour since registration time, most of them
          must be set to registering the <structname>drm_driver</structname>
          instance.
        </para>
        <synopsis>u32 driver_features;</synopsis>
        <variablelist>
          <title>Driver Feature Flags</title>
          <varlistentry>
            <term>DRIVER_USE_AGP</term>
            <listitem><para>
              Driver uses AGP interface, the DRM core will manage AGP resources.
            </para></listitem>
          </varlistentry>
          <varlistentry>
            <term>DRIVER_REQUIRE_AGP</term>
            <listitem><para>
              Driver needs AGP interface to function. AGP initialization failure
              will become a fatal error.
            </para></listitem>
          </varlistentry>
          <varlistentry>
            <term>DRIVER_PCI_DMA</term>
            <listitem><para>
              Driver is capable of PCI DMA, mapping of PCI DMA buffers to
              userspace will be enabled. Deprecated.
            </para></listitem>
          </varlistentry>
          <varlistentry>
            <term>DRIVER_SG</term>
            <listitem><para>
              Driver can perform scatter/gather DMA, allocation and mapping of
              scatter/gather buffers will be enabled. Deprecated.
            </para></listitem>
          </varlistentry>
          <varlistentry>
            <term>DRIVER_HAVE_DMA</term>
            <listitem><para>
              Driver supports DMA, the userspace DMA API will be supported.
              Deprecated.
            </para></listitem>
          </varlistentry>
          <varlistentry>
            <term>DRIVER_HAVE_IRQ</term><term>DRIVER_IRQ_SHARED</term>
            <listitem><para>
              DRIVER_HAVE_IRQ indicates whether the driver has an IRQ handler
              managed by the DRM Core. The core will support simple IRQ handler
              installation when the flag is set. The installation process is
              described in <xref linkend="drm-irq-registration"/>.</para>
              <para>DRIVER_IRQ_SHARED indicates whether the device &amp; handler
              support shared IRQs (note that this is required of PCI  drivers).
            </para></listitem>
          </varlistentry>
          <varlistentry>
            <term>DRIVER_GEM</term>
            <listitem><para>
              Driver use the GEM memory manager.
            </para></listitem>
          </varlistentry>
          <varlistentry>
            <term>DRIVER_MODESET</term>
            <listitem><para>
              Driver supports mode setting interfaces (KMS).
            </para></listitem>
          </varlistentry>
          <varlistentry>
            <term>DRIVER_PRIME</term>
            <listitem><para>
              Driver implements DRM PRIME buffer sharing.
            </para></listitem>
          </varlistentry>
          <varlistentry>
            <term>DRIVER_RENDER</term>
            <listitem><para>
              Driver supports dedicated render nodes.
            </para></listitem>
          </varlistentry>
        </variablelist>
      </sect3>
      <sect3>
        <title>Major, Minor and Patchlevel</title>
        <synopsis>int major;
int minor;
int patchlevel;</synopsis>
        <para>
          The DRM core identifies driver versions by a major, minor and patch
          level triplet. The information is printed to the kernel log at
          initialization time and passed to userspace through the
          DRM_IOCTL_VERSION ioctl.
        </para>
        <para>
          The major and minor numbers are also used to verify the requested driver
          API version passed to DRM_IOCTL_SET_VERSION. When the driver API changes
          between minor versions, applications can call DRM_IOCTL_SET_VERSION to
          select a specific version of the API. If the requested major isn't equal
          to the driver major, or the requested minor is larger than the driver
          minor, the DRM_IOCTL_SET_VERSION call will return an error. Otherwise
          the driver's set_version() method will be called with the requested
          version.
        </para>
      </sect3>
      <sect3>
        <title>Name, Description and Date</title>
        <synopsis>char *name;
char *desc;
char *date;</synopsis>
        <para>
          The driver name is printed to the kernel log at initialization time,
          used for IRQ registration and passed to userspace through
          DRM_IOCTL_VERSION.
        </para>
        <para>
          The driver description is a purely informative string passed to
          userspace through the DRM_IOCTL_VERSION ioctl and otherwise unused by
          the kernel.
        </para>
        <para>
          The driver date, formatted as YYYYMMDD, is meant to identify the date of
          the latest modification to the driver. However, as most drivers fail to
          update it, its value is mostly useless. The DRM core prints it to the
          kernel log at initialization time and passes it to userspace through the
          DRM_IOCTL_VERSION ioctl.
        </para>
      </sect3>
    </sect2>
    <sect2>
      <title>Device Registration</title>
      <para>
        A number of functions are provided to help with device registration.
        The functions deal with PCI, USB and platform devices, respectively.
      </para>
!Edrivers/gpu/drm/drm_pci.c
!Edrivers/gpu/drm/drm_usb.c
!Edrivers/gpu/drm/drm_platform.c
      <para>
        New drivers that no longer rely on the services provided by the
        <structname>drm_bus</structname> structure can call the low-level
        device registration functions directly. The
        <function>drm_dev_alloc()</function> function can be used to allocate
        and initialize a new <structname>drm_device</structname> structure.
        Drivers will typically want to perform some additional setup on this
        structure, such as allocating driver-specific data and storing a
        pointer to it in the DRM device's <structfield>dev_private</structfield>
        field. Drivers should also set the device's unique name using the
        <function>drm_dev_set_unique()</function> function. After it has been
        set up a device can be registered with the DRM subsystem by calling
        <function>drm_dev_register()</function>. This will cause the device to
        be exposed to userspace and will call the driver's
        <structfield>.load()</structfield> implementation. When a device is
        removed, the DRM device can safely be unregistered and freed by calling
        <function>drm_dev_unregister()</function> followed by a call to
        <function>drm_dev_unref()</function>.
      </para>
!Edrivers/gpu/drm/drm_stub.c
    </sect2>
    <sect2>
      <title>Driver Load</title>
      <para>
        The <methodname>load</methodname> method is the driver and device
        initialization entry point. The method is responsible for allocating and
        initializing driver private data, performing resource allocation and
        mapping (e.g. acquiring
        clocks, mapping registers or allocating command buffers), initializing
        the memory manager (<xref linkend="drm-memory-management"/>), installing
        the IRQ handler (<xref linkend="drm-irq-registration"/>), setting up
        vertical blanking handling (<xref linkend="drm-vertical-blank"/>), mode
        setting (<xref linkend="drm-mode-setting"/>) and initial output
        configuration (<xref linkend="drm-kms-init"/>).
      </para>
      <note><para>
        If compatibility is a concern (e.g. with drivers converted over from
        User Mode Setting to Kernel Mode Setting), care must be taken to prevent
        device initialization and control that is incompatible with currently
        active userspace drivers. For instance, if user level mode setting
        drivers are in use, it would be problematic to perform output discovery
        &amp; configuration at load time. Likewise, if user-level drivers
        unaware of memory management are in use, memory management and command
        buffer setup may need to be omitted. These requirements are
        driver-specific, and care needs to be taken to keep both old and new
        applications and libraries working.
      </para></note>
      <synopsis>int (*load) (struct drm_device *, unsigned long flags);</synopsis>
      <para>
        The method takes two arguments, a pointer to the newly created
        <structname>drm_device</structname> and flags. The flags are used to
        pass the <structfield>driver_data</structfield> field of the device id
        corresponding to the device passed to <function>drm_*_init()</function>.
        Only PCI devices currently use this, USB and platform DRM drivers have
        their <methodname>load</methodname> method called with flags to 0.
      </para>
      <sect3>
        <title>Driver Private Data</title>
        <para>
          The driver private hangs off the main
          <structname>drm_device</structname> structure and can be used for
          tracking various device-specific bits of information, like register
          offsets, command buffer status, register state for suspend/resume, etc.
          At load time, a driver may simply allocate one and set
          <structname>drm_device</structname>.<structfield>dev_priv</structfield>
          appropriately; it should be freed and
          <structname>drm_device</structname>.<structfield>dev_priv</structfield>
          set to NULL when the driver is unloaded.
        </para>
      </sect3>
      <sect3 id="drm-irq-registration">
        <title>IRQ Registration</title>
        <para>
          The DRM core tries to facilitate IRQ handler registration and
          unregistration by providing <function>drm_irq_install</function> and
          <function>drm_irq_uninstall</function> functions. Those functions only
          support a single interrupt per device, devices that use more than one
          IRQs need to be handled manually.
        </para>
        <sect4>
          <title>Managed IRQ Registration</title>
          <para>
            <function>drm_irq_install</function> starts by calling the
            <methodname>irq_preinstall</methodname> driver operation. The operation
            is optional and must make sure that the interrupt will not get fired by
            clearing all pending interrupt flags or disabling the interrupt.
          </para>
          <para>
            The passed-in IRQ will then be requested by a call to
            <function>request_irq</function>. If the DRIVER_IRQ_SHARED driver
            feature flag is set, a shared (IRQF_SHARED) IRQ handler will be
            requested.
          </para>
          <para>
            The IRQ handler function must be provided as the mandatory irq_handler
            driver operation. It will get passed directly to
            <function>request_irq</function> and thus has the same prototype as all
            IRQ handlers. It will get called with a pointer to the DRM device as the
            second argument.
          </para>
          <para>
            Finally the function calls the optional
            <methodname>irq_postinstall</methodname> driver operation. The operation
            usually enables interrupts (excluding the vblank interrupt, which is
            enabled separately), but drivers may choose to enable/disable interrupts
            at a different time.
          </para>
          <para>
            <function>drm_irq_uninstall</function> is similarly used to uninstall an
            IRQ handler. It starts by waking up all processes waiting on a vblank
            interrupt to make sure they don't hang, and then calls the optional
            <methodname>irq_uninstall</methodname> driver operation. The operation
            must disable all hardware interrupts. Finally the function frees the IRQ
            by calling <function>free_irq</function>.
          </para>
        </sect4>
        <sect4>
          <title>Manual IRQ Registration</title>
          <para>
            Drivers that require multiple interrupt handlers can't use the managed
            IRQ registration functions. In that case IRQs must be registered and
            unregistered manually (usually with the <function>request_irq</function>
            and <function>free_irq</function> functions, or their devm_* equivalent).
          </para>
          <para>
            When manually registering IRQs, drivers must not set the DRIVER_HAVE_IRQ
            driver feature flag, and must not provide the
            <methodname>irq_handler</methodname> driver operation. They must set the
            <structname>drm_device</structname> <structfield>irq_enabled</structfield>
            field to 1 upon registration of the IRQs, and clear it to 0 after
            unregistering the IRQs.
          </para>
        </sect4>
      </sect3>
      <sect3>
        <title>Memory Manager Initialization</title>
        <para>
          Every DRM driver requires a memory manager which must be initialized at
          load time. DRM currently contains two memory managers, the Translation
          Table Manager (TTM) and the Graphics Execution Manager (GEM).
          This document describes the use of the GEM memory manager only. See
          <xref linkend="drm-memory-management"/> for details.
        </para>
      </sect3>
      <sect3>
        <title>Miscellaneous Device Configuration</title>
        <para>
          Another task that may be necessary for PCI devices during configuration
          is mapping the video BIOS. On many devices, the VBIOS describes device
          configuration, LCD panel timings (if any), and contains flags indicating
          device state. Mapping the BIOS can be done using the pci_map_rom() call,
          a convenience function that takes care of mapping the actual ROM,
          whether it has been shadowed into memory (typically at address 0xc0000)
          or exists on the PCI device in the ROM BAR. Note that after the ROM has
          been mapped and any necessary information has been extracted, it should
          be unmapped; on many devices, the ROM address decoder is shared with
          other BARs, so leaving it mapped could cause undesired behaviour like
          hangs or memory corruption.
  <!--!Fdrivers/pci/rom.c pci_map_rom-->
        </para>
      </sect3>
    </sect2>
  </sect1>

  <!-- Internals: memory management -->

  <sect1 id="drm-memory-management">
    <title>Memory management</title>
    <para>
      Modern Linux systems require large amount of graphics memory to store
      frame buffers, textures, vertices and other graphics-related data. Given
      the very dynamic nature of many of that data, managing graphics memory
      efficiently is thus crucial for the graphics stack and plays a central
      role in the DRM infrastructure.
    </para>
    <para>
      The DRM core includes two memory managers, namely Translation Table Maps
      (TTM) and Graphics Execution Manager (GEM). TTM was the first DRM memory
      manager to be developed and tried to be a one-size-fits-them all
      solution. It provides a single userspace API to accommodate the need of
      all hardware, supporting both Unified Memory Architecture (UMA) devices
      and devices with dedicated video RAM (i.e. most discrete video cards).
      This resulted in a large, complex piece of code that turned out to be
      hard to use for driver development.
    </para>
    <para>
      GEM started as an Intel-sponsored project in reaction to TTM's
      complexity. Its design philosophy is completely different: instead of
      providing a solution to every graphics memory-related problems, GEM
      identified common code between drivers and created a support library to
      share it. GEM has simpler initialization and execution requirements than
      TTM, but has no video RAM management capabilities and is thus limited to
      UMA devices.
    </para>
    <sect2>
      <title>The Translation Table Manager (TTM)</title>
      <para>
        TTM design background and information belongs here.
      </para>
      <sect3>
        <title>TTM initialization</title>
        <warning><para>This section is outdated.</para></warning>
        <para>
          Drivers wishing to support TTM must fill out a drm_bo_driver
          structure. The structure contains several fields with function
          pointers for initializing the TTM, allocating and freeing memory,
          waiting for command completion and fence synchronization, and memory
          migration. See the radeon_ttm.c file for an example of usage.
        </para>
        <para>
          The ttm_global_reference structure is made up of several fields:
        </para>
        <programlisting>
          struct ttm_global_reference {
                enum ttm_global_types global_type;
                size_t size;
                void *object;
                int (*init) (struct ttm_global_reference *);
                void (*release) (struct ttm_global_reference *);
          };
        </programlisting>
        <para>
          There should be one global reference structure for your memory
          manager as a whole, and there will be others for each object
          created by the memory manager at runtime.  Your global TTM should
          have a type of TTM_GLOBAL_TTM_MEM.  The size field for the global
          object should be sizeof(struct ttm_mem_global), and the init and
          release hooks should point at your driver-specific init and
          release routines, which probably eventually call
          ttm_mem_global_init and ttm_mem_global_release, respectively.
        </para>
        <para>
          Once your global TTM accounting structure is set up and initialized
          by calling ttm_global_item_ref() on it,
          you need to create a buffer object TTM to
          provide a pool for buffer object allocation by clients and the
          kernel itself.  The type of this object should be TTM_GLOBAL_TTM_BO,
          and its size should be sizeof(struct ttm_bo_global).  Again,
          driver-specific init and release functions may be provided,
          likely eventually calling ttm_bo_global_init() and
          ttm_bo_global_release(), respectively.  Also, like the previous
          object, ttm_global_item_ref() is used to create an initial reference
          count for the TTM, which will call your initialization function.
        </para>
      </sect3>
    </sect2>
    <sect2 id="drm-gem">
      <title>The Graphics Execution Manager (GEM)</title>
      <para>
        The GEM design approach has resulted in a memory manager that doesn't
        provide full coverage of all (or even all common) use cases in its
        userspace or kernel API. GEM exposes a set of standard memory-related
        operations to userspace and a set of helper functions to drivers, and let
        drivers implement hardware-specific operations with their own private API.
      </para>
      <para>
        The GEM userspace API is described in the
        <ulink url="http://lwn.net/Articles/283798/"><citetitle>GEM - the Graphics
        Execution Manager</citetitle></ulink> article on LWN. While slightly
        outdated, the document provides a good overview of the GEM API principles.
        Buffer allocation and read and write operations, described as part of the
        common GEM API, are currently implemented using driver-specific ioctls.
      </para>
      <para>
        GEM is data-agnostic. It manages abstract buffer objects without knowing
        what individual buffers contain. APIs that require knowledge of buffer
        contents or purpose, such as buffer allocation or synchronization
        primitives, are thus outside of the scope of GEM and must be implemented
        using driver-specific ioctls.
      </para>
      <para>
        On a fundamental level, GEM involves several operations:
        <itemizedlist>
          <listitem>Memory allocation and freeing</listitem>
          <listitem>Command execution</listitem>
          <listitem>Aperture management at command execution time</listitem>
        </itemizedlist>
        Buffer object allocation is relatively straightforward and largely
        provided by Linux's shmem layer, which provides memory to back each
        object.
      </para>
      <para>
        Device-specific operations, such as command execution, pinning, buffer
        read &amp; write, mapping, and domain ownership transfers are left to
        driver-specific ioctls.
      </para>
      <sect3>
        <title>GEM Initialization</title>
        <para>
          Drivers that use GEM must set the DRIVER_GEM bit in the struct
          <structname>drm_driver</structname>
          <structfield>driver_features</structfield> field. The DRM core will
          then automatically initialize the GEM core before calling the
          <methodname>load</methodname> operation. Behind the scene, this will
          create a DRM Memory Manager object which provides an address space
          pool for object allocation.
        </para>
        <para>
          In a KMS configuration, drivers need to allocate and initialize a
          command ring buffer following core GEM initialization if required by
          the hardware. UMA devices usually have what is called a "stolen"
          memory region, which provides space for the initial framebuffer and
          large, contiguous memory regions required by the device. This space is
          typically not managed by GEM, and must be initialized separately into
          its own DRM MM object.
        </para>
      </sect3>
      <sect3>
        <title>GEM Objects Creation</title>
        <para>
          GEM splits creation of GEM objects and allocation of the memory that
          backs them in two distinct operations.
        </para>
        <para>
          GEM objects are represented by an instance of struct
          <structname>drm_gem_object</structname>. Drivers usually need to extend
          GEM objects with private information and thus create a driver-specific
          GEM object structure type that embeds an instance of struct
          <structname>drm_gem_object</structname>.
        </para>
        <para>
          To create a GEM object, a driver allocates memory for an instance of its
          specific GEM object type and initializes the embedded struct
          <structname>drm_gem_object</structname> with a call to
          <function>drm_gem_object_init</function>. The function takes a pointer to
          the DRM device, a pointer to the GEM object and the buffer object size
          in bytes.
        </para>
        <para>
          GEM uses shmem to allocate anonymous pageable memory.
          <function>drm_gem_object_init</function> will create an shmfs file of
          the requested size and store it into the struct
          <structname>drm_gem_object</structname> <structfield>filp</structfield>
          field. The memory is used as either main storage for the object when the
          graphics hardware uses system memory directly or as a backing store
          otherwise.
        </para>
        <para>
          Drivers are responsible for the actual physical pages allocation by
          calling <function>shmem_read_mapping_page_gfp</function> for each page.
          Note that they can decide to allocate pages when initializing the GEM
          object, or to delay allocation until the memory is needed (for instance
          when a page fault occurs as a result of a userspace memory access or
          when the driver needs to start a DMA transfer involving the memory).
        </para>
        <para>
          Anonymous pageable memory allocation is not always desired, for instance
          when the hardware requires physically contiguous system memory as is
          often the case in embedded devices. Drivers can create GEM objects with
          no shmfs backing (called private GEM objects) by initializing them with
          a call to <function>drm_gem_private_object_init</function> instead of
          <function>drm_gem_object_init</function>. Storage for private GEM
          objects must be managed by drivers.
        </para>
        <para>
          Drivers that do not need to extend GEM objects with private information
          can call the <function>drm_gem_object_alloc</function> function to
          allocate and initialize a struct <structname>drm_gem_object</structname>
          instance. The GEM core will call the optional driver
          <methodname>gem_init_object</methodname> operation after initializing
          the GEM object with <function>drm_gem_object_init</function>.
          <synopsis>int (*gem_init_object) (struct drm_gem_object *obj);</synopsis>
        </para>
        <para>
          No alloc-and-init function exists for private GEM objects.
        </para>
      </sect3>
      <sect3>
        <title>GEM Objects Lifetime</title>
        <para>
          All GEM objects are reference-counted by the GEM core. References can be
          acquired and release by <function>calling drm_gem_object_reference</function>
          and <function>drm_gem_object_unreference</function> respectively. The
          caller must hold the <structname>drm_device</structname>
          <structfield>struct_mutex</structfield> lock. As a convenience, GEM
          provides the <function>drm_gem_object_reference_unlocked</function> and
          <function>drm_gem_object_unreference_unlocked</function> functions that
          can be called without holding the lock.
        </para>
        <para>
          When the last reference to a GEM object is released the GEM core calls
          the <structname>drm_driver</structname>
          <methodname>gem_free_object</methodname> operation. That operation is
          mandatory for GEM-enabled drivers and must free the GEM object and all
          associated resources.
        </para>
        <para>
          <synopsis>void (*gem_free_object) (struct drm_gem_object *obj);</synopsis>
          Drivers are responsible for freeing all GEM object resources, including
          the resources created by the GEM core. If an mmap offset has been
          created for the object (in which case
          <structname>drm_gem_object</structname>::<structfield>map_list</structfield>::<structfield>map</structfield>
          is not NULL) it must be freed by a call to
          <function>drm_gem_free_mmap_offset</function>. The shmfs backing store
          must be released by calling <function>drm_gem_object_release</function>
          (that function can safely be called if no shmfs backing store has been
          created).
        </para>
      </sect3>
      <sect3>
        <title>GEM Objects Naming</title>
        <para>
          Communication between userspace and the kernel refers to GEM objects
          using local handles, global names or, more recently, file descriptors.
          All of those are 32-bit integer values; the usual Linux kernel limits
          apply to the file descriptors.
        </para>
        <para>
          GEM handles are local to a DRM file. Applications get a handle to a GEM
          object through a driver-specific ioctl, and can use that handle to refer
          to the GEM object in other standard or driver-specific ioctls. Closing a
          DRM file handle frees all its GEM handles and dereferences the
          associated GEM objects.
        </para>
        <para>
          To create a handle for a GEM object drivers call
          <function>drm_gem_handle_create</function>. The function takes a pointer
          to the DRM file and the GEM object and returns a locally unique handle.
          When the handle is no longer needed drivers delete it with a call to
          <function>drm_gem_handle_delete</function>. Finally the GEM object
          associated with a handle can be retrieved by a call to
          <function>drm_gem_object_lookup</function>.
        </para>
        <para>
          Handles don't take ownership of GEM objects, they only take a reference
          to the object that will be dropped when the handle is destroyed. To
          avoid leaking GEM objects, drivers must make sure they drop the
          reference(s) they own (such as the initial reference taken at object
          creation time) as appropriate, without any special consideration for the
          handle. For example, in the particular case of combined GEM object and
          handle creation in the implementation of the
          <methodname>dumb_create</methodname> operation, drivers must drop the
          initial reference to the GEM object before returning the handle.
        </para>
        <para>
          GEM names are similar in purpose to handles but are not local to DRM
          files. They can be passed between processes to reference a GEM object
          globally. Names can't be used directly to refer to objects in the DRM
          API, applications must convert handles to names and names to handles
          using the DRM_IOCTL_GEM_FLINK and DRM_IOCTL_GEM_OPEN ioctls
          respectively. The conversion is handled by the DRM core without any
          driver-specific support.
        </para>
        <para>
          GEM also supports buffer sharing with dma-buf file descriptors through
          PRIME. GEM-based drivers must use the provided helpers functions to
          implement the exporting and importing correctly. See <xref linkend="drm-prime-support" />.
          Since sharing file descriptors is inherently more secure than the
          easily guessable and global GEM names it is the preferred buffer
          sharing mechanism. Sharing buffers through GEM names is only supported
          for legacy userspace. Furthermore PRIME also allows cross-device
          buffer sharing since it is based on dma-bufs.
        </para>
      </sect3>
      <sect3 id="drm-gem-objects-mapping">
        <title>GEM Objects Mapping</title>
        <para>
          Because mapping operations are fairly heavyweight GEM favours
          read/write-like access to buffers, implemented through driver-specific
          ioctls, over mapping buffers to userspace. However, when random access
          to the buffer is needed (to perform software rendering for instance),
          direct access to the object can be more efficient.
        </para>
        <para>
          The mmap system call can't be used directly to map GEM objects, as they
          don't have their own file handle. Two alternative methods currently
          co-exist to map GEM objects to userspace. The first method uses a
          driver-specific ioctl to perform the mapping operation, calling
          <function>do_mmap</function> under the hood. This is often considered
          dubious, seems to be discouraged for new GEM-enabled drivers, and will
          thus not be described here.
        </para>
        <para>
          The second method uses the mmap system call on the DRM file handle.
          <synopsis>void *mmap(void *addr, size_t length, int prot, int flags, int fd,
             off_t offset);</synopsis>
          DRM identifies the GEM object to be mapped by a fake offset passed
          through the mmap offset argument. Prior to being mapped, a GEM object
          must thus be associated with a fake offset. To do so, drivers must call
          <function>drm_gem_create_mmap_offset</function> on the object. The
          function allocates a fake offset range from a pool and stores the
          offset divided by PAGE_SIZE in
          <literal>obj-&gt;map_list.hash.key</literal>. Care must be taken not to
          call <function>drm_gem_create_mmap_offset</function> if a fake offset
          has already been allocated for the object. This can be tested by
          <literal>obj-&gt;map_list.map</literal> being non-NULL.
        </para>
        <para>
          Once allocated, the fake offset value
          (<literal>obj-&gt;map_list.hash.key &lt;&lt; PAGE_SHIFT</literal>)
          must be passed to the application in a driver-specific way and can then
          be used as the mmap offset argument.
        </para>
        <para>
          The GEM core provides a helper method <function>drm_gem_mmap</function>
          to handle object mapping. The method can be set directly as the mmap
          file operation handler. It will look up the GEM object based on the
          offset value and set the VMA operations to the
          <structname>drm_driver</structname> <structfield>gem_vm_ops</structfield>
          field. Note that <function>drm_gem_mmap</function> doesn't map memory to
          userspace, but relies on the driver-provided fault handler to map pages
          individually.
        </para>
        <para>
          To use <function>drm_gem_mmap</function>, drivers must fill the struct
          <structname>drm_driver</structname> <structfield>gem_vm_ops</structfield>
          field with a pointer to VM operations.
        </para>
        <para>
          <synopsis>struct vm_operations_struct *gem_vm_ops

  struct vm_operations_struct {
          void (*open)(struct vm_area_struct * area);
          void (*close)(struct vm_area_struct * area);
          int (*fault)(struct vm_area_struct *vma, struct vm_fault *vmf);
  };</synopsis>
        </para>
        <para>
          The <methodname>open</methodname> and <methodname>close</methodname>
          operations must update the GEM object reference count. Drivers can use
          the <function>drm_gem_vm_open</function> and
          <function>drm_gem_vm_close</function> helper functions directly as open
          and close handlers.
        </para>
        <para>
          The fault operation handler is responsible for mapping individual pages
          to userspace when a page fault occurs. Depending on the memory
          allocation scheme, drivers can allocate pages at fault time, or can
          decide to allocate memory for the GEM object at the time the object is
          created.
        </para>
        <para>
          Drivers that want to map the GEM object upfront instead of handling page
          faults can implement their own mmap file operation handler.
        </para>
      </sect3>
      <sect3>
        <title>Memory Coherency</title>
        <para>
          When mapped to the device or used in a command buffer, backing pages
          for an object are flushed to memory and marked write combined so as to
          be coherent with the GPU. Likewise, if the CPU accesses an object
          after the GPU has finished rendering to the object, then the object
          must be made coherent with the CPU's view of memory, usually involving
          GPU cache flushing of various kinds. This core CPU&lt;-&gt;GPU
          coherency management is provided by a device-specific ioctl, which
          evaluates an object's current domain and performs any necessary
          flushing or synchronization to put the object into the desired
          coherency domain (note that the object may be busy, i.e. an active
          render target; in that case, setting the domain blocks the client and
          waits for rendering to complete before performing any necessary
          flushing operations).
        </para>
      </sect3>
      <sect3>
        <title>Command Execution</title>
        <para>
          Perhaps the most important GEM function for GPU devices is providing a
          command execution interface to clients. Client programs construct
          command buffers containing references to previously allocated memory
          objects, and then submit them to GEM. At that point, GEM takes care to
          bind all the objects into the GTT, execute the buffer, and provide
          necessary synchronization between clients accessing the same buffers.
          This often involves evicting some objects from the GTT and re-binding
          others (a fairly expensive operation), and providing relocation
          support which hides fixed GTT offsets from clients. Clients must take
          care not to submit command buffers that reference more objects than
          can fit in the GTT; otherwise, GEM will reject them and no rendering
          will occur. Similarly, if several objects in the buffer require fence
          registers to be allocated for correct rendering (e.g. 2D blits on
          pre-965 chips), care must be taken not to require more fence registers
          than are available to the client. Such resource management should be
          abstracted from the client in libdrm.
        </para>
      </sect3>
      <sect3>
        <title>GEM Function Reference</title>
!Edrivers/gpu/drm/drm_gem.c
      </sect3>
      </sect2>
      <sect2>
        <title>VMA Offset Manager</title>
!Pdrivers/gpu/drm/drm_vma_manager.c vma offset manager
!Edrivers/gpu/drm/drm_vma_manager.c
!Iinclude/drm/drm_vma_manager.h
      </sect2>
      <sect2 id="drm-prime-support">
        <title>PRIME Buffer Sharing</title>
        <para>
          PRIME is the cross device buffer sharing framework in drm, originally
          created for the OPTIMUS range of multi-gpu platforms. To userspace
          PRIME buffers are dma-buf based file descriptors.
        </para>
        <sect3>
          <title>Overview and Driver Interface</title>
          <para>
            Similar to GEM global names, PRIME file descriptors are
            also used to share buffer objects across processes. They offer
            additional security: as file descriptors must be explicitly sent over
            UNIX domain sockets to be shared between applications, they can't be
            guessed like the globally unique GEM names.
          </para>
          <para>
            Drivers that support the PRIME
            API must set the DRIVER_PRIME bit in the struct
            <structname>drm_driver</structname>
            <structfield>driver_features</structfield> field, and implement the
            <methodname>prime_handle_to_fd</methodname> and
            <methodname>prime_fd_to_handle</methodname> operations.
          </para>
          <para>
            <synopsis>int (*prime_handle_to_fd)(struct drm_device *dev,
                          struct drm_file *file_priv, uint32_t handle,
                          uint32_t flags, int *prime_fd);
int (*prime_fd_to_handle)(struct drm_device *dev,
                          struct drm_file *file_priv, int prime_fd,
                          uint32_t *handle);</synopsis>
            Those two operations convert a handle to a PRIME file descriptor and
            vice versa. Drivers must use the kernel dma-buf buffer sharing framework
            to manage the PRIME file descriptors. Similar to the mode setting
            API PRIME is agnostic to the underlying buffer object manager, as
            long as handles are 32bit unsigned integers.
          </para>
          <para>
            While non-GEM drivers must implement the operations themselves, GEM
            drivers must use the <function>drm_gem_prime_handle_to_fd</function>
            and <function>drm_gem_prime_fd_to_handle</function> helper functions.
            Those helpers rely on the driver
            <methodname>gem_prime_export</methodname> and
            <methodname>gem_prime_import</methodname> operations to create a dma-buf
            instance from a GEM object (dma-buf exporter role) and to create a GEM
            object from a dma-buf instance (dma-buf importer role).
          </para>
          <para>
            <synopsis>struct dma_buf * (*gem_prime_export)(struct drm_device *dev,
                                     struct drm_gem_object *obj,
                                     int flags);
struct drm_gem_object * (*gem_prime_import)(struct drm_device *dev,
                                            struct dma_buf *dma_buf);</synopsis>
            These two operations are mandatory for GEM drivers that support
            PRIME.
          </para>
        </sect3>
        <sect3>
          <title>PRIME Helper Functions</title>
!Pdrivers/gpu/drm/drm_prime.c PRIME Helpers
        </sect3>
      </sect2>
      <sect2>
        <title>PRIME Function References</title>
!Edrivers/gpu/drm/drm_prime.c
      </sect2>
      <sect2>
        <title>DRM MM Range Allocator</title>
        <sect3>
          <title>Overview</title>
!Pdrivers/gpu/drm/drm_mm.c Overview
        </sect3>
        <sect3>
          <title>LRU Scan/Eviction Support</title>
!Pdrivers/gpu/drm/drm_mm.c lru scan roaster
        </sect3>
      </sect2>
      <sect2>
        <title>DRM MM Range Allocator Function References</title>
!Edrivers/gpu/drm/drm_mm.c
!Iinclude/drm/drm_mm.h
      </sect2>
  </sect1>

  <!-- Internals: mode setting -->

  <sect1 id="drm-mode-setting">
    <title>Mode Setting</title>
    <para>
      Drivers must initialize the mode setting core by calling
      <function>drm_mode_config_init</function> on the DRM device. The function
      initializes the <structname>drm_device</structname>
      <structfield>mode_config</structfield> field and never fails. Once done,
      mode configuration must be setup by initializing the following fields.
    </para>
    <itemizedlist>
      <listitem>
        <synopsis>int min_width, min_height;
int max_width, max_height;</synopsis>
        <para>
          Minimum and maximum width and height of the frame buffers in pixel
          units.
        </para>
      </listitem>
      <listitem>
        <synopsis>struct drm_mode_config_funcs *funcs;</synopsis>
        <para>Mode setting functions.</para>
      </listitem>
    </itemizedlist>
    <sect2>
      <title>Display Modes Function Reference</title>
!Iinclude/drm/drm_modes.h
!Edrivers/gpu/drm/drm_modes.c
    </sect2>
    <sect2>
      <title>Frame Buffer Creation</title>
      <synopsis>struct drm_framebuffer *(*fb_create)(struct drm_device *dev,
                                     struct drm_file *file_priv,
                                     struct drm_mode_fb_cmd2 *mode_cmd);</synopsis>
      <para>
        Frame buffers are abstract memory objects that provide a source of
        pixels to scanout to a CRTC. Applications explicitly request the
        creation of frame buffers through the DRM_IOCTL_MODE_ADDFB(2) ioctls and
        receive an opaque handle that can be passed to the KMS CRTC control,
        plane configuration and page flip functions.
      </para>
      <para>
        Frame buffers rely on the underneath memory manager for low-level memory
        operations. When creating a frame buffer applications pass a memory
        handle (or a list of memory handles for multi-planar formats) through
        the <parameter>drm_mode_fb_cmd2</parameter> argument. For drivers using
        GEM as their userspace buffer management interface this would be a GEM
        handle.  Drivers are however free to use their own backing storage object
        handles, e.g. vmwgfx directly exposes special TTM handles to userspace
        and so expects TTM handles in the create ioctl and not GEM handles.
      </para>
      <para>
        Drivers must first validate the requested frame buffer parameters passed
        through the mode_cmd argument. In particular this is where invalid
        sizes, pixel formats or pitches can be caught.
      </para>
      <para>
        If the parameters are deemed valid, drivers then create, initialize and
        return an instance of struct <structname>drm_framebuffer</structname>.
        If desired the instance can be embedded in a larger driver-specific
        structure. Drivers must fill its <structfield>width</structfield>,
        <structfield>height</structfield>, <structfield>pitches</structfield>,
        <structfield>offsets</structfield>, <structfield>depth</structfield>,
        <structfield>bits_per_pixel</structfield> and
        <structfield>pixel_format</structfield> fields from the values passed
        through the <parameter>drm_mode_fb_cmd2</parameter> argument. They
        should call the <function>drm_helper_mode_fill_fb_struct</function>
        helper function to do so.
      </para>

      <para>
        The initialization of the new framebuffer instance is finalized with a
        call to <function>drm_framebuffer_init</function> which takes a pointer
        to DRM frame buffer operations (struct
        <structname>drm_framebuffer_funcs</structname>). Note that this function
        publishes the framebuffer and so from this point on it can be accessed
        concurrently from other threads. Hence it must be the last step in the
        driver's framebuffer initialization sequence. Frame buffer operations
        are
        <itemizedlist>
          <listitem>
            <synopsis>int (*create_handle)(struct drm_framebuffer *fb,
                     struct drm_file *file_priv, unsigned int *handle);</synopsis>
            <para>
              Create a handle to the frame buffer underlying memory object. If
              the frame buffer uses a multi-plane format, the handle will
              reference the memory object associated with the first plane.
            </para>
            <para>
              Drivers call <function>drm_gem_handle_create</function> to create
              the handle.
            </para>
          </listitem>
          <listitem>
            <synopsis>void (*destroy)(struct drm_framebuffer *framebuffer);</synopsis>
            <para>
              Destroy the frame buffer object and frees all associated
              resources. Drivers must call
              <function>drm_framebuffer_cleanup</function> to free resources
              allocated by the DRM core for the frame buffer object, and must
              make sure to unreference all memory objects associated with the
              frame buffer. Handles created by the
              <methodname>create_handle</methodname> operation are released by
              the DRM core.
            </para>
          </listitem>
          <listitem>
            <synopsis>int (*dirty)(struct drm_framebuffer *framebuffer,
             struct drm_file *file_priv, unsigned flags, unsigned color,
             struct drm_clip_rect *clips, unsigned num_clips);</synopsis>
            <para>
              This optional operation notifies the driver that a region of the
              frame buffer has changed in response to a DRM_IOCTL_MODE_DIRTYFB
              ioctl call.
            </para>
          </listitem>
        </itemizedlist>
      </para>
      <para>
        The lifetime of a drm framebuffer is controlled with a reference count,
        drivers can grab additional references with
        <function>drm_framebuffer_reference</function>and drop them
        again with <function>drm_framebuffer_unreference</function>. For
        driver-private framebuffers for which the last reference is never
        dropped (e.g. for the fbdev framebuffer when the struct
        <structname>drm_framebuffer</structname> is embedded into the fbdev
        helper struct) drivers can manually clean up a framebuffer at module
        unload time with
        <function>drm_framebuffer_unregister_private</function>.
      </para>
    </sect2>
    <sect2>
      <title>Dumb Buffer Objects</title>
      <para>
        The KMS API doesn't standardize backing storage object creation and
        leaves it to driver-specific ioctls. Furthermore actually creating a
        buffer object even for GEM-based drivers is done through a
        driver-specific ioctl - GEM only has a common userspace interface for
        sharing and destroying objects. While not an issue for full-fledged
        graphics stacks that include device-specific userspace components (in
        libdrm for instance), this limit makes DRM-based early boot graphics
        unnecessarily complex.
      </para>
      <para>
        Dumb objects partly alleviate the problem by providing a standard
        API to create dumb buffers suitable for scanout, which can then be used
        to create KMS frame buffers.
      </para>
      <para>
        To support dumb objects drivers must implement the
        <methodname>dumb_create</methodname>,
        <methodname>dumb_destroy</methodname> and
        <methodname>dumb_map_offset</methodname> operations.
      </para>
      <itemizedlist>
        <listitem>
          <synopsis>int (*dumb_create)(struct drm_file *file_priv, struct drm_device *dev,
                   struct drm_mode_create_dumb *args);</synopsis>
          <para>
            The <methodname>dumb_create</methodname> operation creates a driver
            object (GEM or TTM handle) suitable for scanout based on the
            width, height and depth from the struct
            <structname>drm_mode_create_dumb</structname> argument. It fills the
            argument's <structfield>handle</structfield>,
            <structfield>pitch</structfield> and <structfield>size</structfield>
            fields with a handle for the newly created object and its line
            pitch and size in bytes.
          </para>
        </listitem>
        <listitem>
          <synopsis>int (*dumb_destroy)(struct drm_file *file_priv, struct drm_device *dev,
                    uint32_t handle);</synopsis>
          <para>
            The <methodname>dumb_destroy</methodname> operation destroys a dumb
            object created by <methodname>dumb_create</methodname>.
          </para>
        </listitem>
        <listitem>
          <synopsis>int (*dumb_map_offset)(struct drm_file *file_priv, struct drm_device *dev,
                       uint32_t handle, uint64_t *offset);</synopsis>
          <para>
            The <methodname>dumb_map_offset</methodname> operation associates an
            mmap fake offset with the object given by the handle and returns
            it. Drivers must use the
            <function>drm_gem_create_mmap_offset</function> function to
            associate the fake offset as described in
            <xref linkend="drm-gem-objects-mapping"/>.
          </para>
        </listitem>
      </itemizedlist>
      <para>
        Note that dumb objects may not be used for gpu acceleration, as has been
        attempted on some ARM embedded platforms. Such drivers really must have
        a hardware-specific ioctl to allocate suitable buffer objects.
      </para>
    </sect2>
    <sect2>
      <title>Output Polling</title>
      <synopsis>void (*output_poll_changed)(struct drm_device *dev);</synopsis>
      <para>
        This operation notifies the driver that the status of one or more
        connectors has changed. Drivers that use the fb helper can just call the
        <function>drm_fb_helper_hotplug_event</function> function to handle this
        operation.
      </para>
    </sect2>
    <sect2>
      <title>Locking</title>
      <para>
        Beside some lookup structures with their own locking (which is hidden
        behind the interface functions) most of the modeset state is protected
        by the <code>dev-&lt;mode_config.lock</code> mutex and additionally
        per-crtc locks to allow cursor updates, pageflips and similar operations
        to occur concurrently with background tasks like output detection.
        Operations which cross domains like a full modeset always grab all
        locks. Drivers there need to protect resources shared between crtcs with
        additional locking. They also need to be careful to always grab the
        relevant crtc locks if a modset functions touches crtc state, e.g. for
        load detection (which does only grab the <code>mode_config.lock</code>
        to allow concurrent screen updates on live crtcs).
      </para>
    </sect2>
  </sect1>

  <!-- Internals: kms initialization and cleanup -->

  <sect1 id="drm-kms-init">
    <title>KMS Initialization and Cleanup</title>
    <para>
      A KMS device is abstracted and exposed as a set of planes, CRTCs, encoders
      and connectors. KMS drivers must thus create and initialize all those
      objects at load time after initializing mode setting.
    </para>
    <sect2>
      <title>CRTCs (struct <structname>drm_crtc</structname>)</title>
      <para>
        A CRTC is an abstraction representing a part of the chip that contains a
        pointer to a scanout buffer. Therefore, the number of CRTCs available
        determines how many independent scanout buffers can be active at any
        given time. The CRTC structure contains several fields to support this:
        a pointer to some video memory (abstracted as a frame buffer object), a
        display mode, and an (x, y) offset into the video memory to support
        panning or configurations where one piece of video memory spans multiple
        CRTCs.
      </para>
      <sect3>
        <title>CRTC Initialization</title>
        <para>
          A KMS device must create and register at least one struct
          <structname>drm_crtc</structname> instance. The instance is allocated
          and zeroed by the driver, possibly as part of a larger structure, and
          registered with a call to <function>drm_crtc_init</function> with a
          pointer to CRTC functions.
        </para>
      </sect3>
      <sect3 id="drm-kms-crtcops">
        <title>CRTC Operations</title>
        <sect4>
          <title>Set Configuration</title>
          <synopsis>int (*set_config)(struct drm_mode_set *set);</synopsis>
          <para>
            Apply a new CRTC configuration to the device. The configuration
            specifies a CRTC, a frame buffer to scan out from, a (x,y) position in
            the frame buffer, a display mode and an array of connectors to drive
            with the CRTC if possible.
          </para>
          <para>
            If the frame buffer specified in the configuration is NULL, the driver
            must detach all encoders connected to the CRTC and all connectors
            attached to those encoders and disable them.
          </para>
          <para>
            This operation is called with the mode config lock held.
          </para>
          <note><para>
            Note that the drm core has no notion of restoring the mode setting
            state after resume, since all resume handling is in the full
            responsibility of the driver. The common mode setting helper library
            though provides a helper which can be used for this:
            <function>drm_helper_resume_force_mode</function>.
          </para></note>
        </sect4>
        <sect4>
          <title>Page Flipping</title>
          <synopsis>int (*page_flip)(struct drm_crtc *crtc, struct drm_framebuffer *fb,
                   struct drm_pending_vblank_event *event);</synopsis>
          <para>
            Schedule a page flip to the given frame buffer for the CRTC. This
            operation is called with the mode config mutex held.
          </para>
          <para>
            Page flipping is a synchronization mechanism that replaces the frame
            buffer being scanned out by the CRTC with a new frame buffer during
            vertical blanking, avoiding tearing. When an application requests a page
            flip the DRM core verifies that the new frame buffer is large enough to
            be scanned out by  the CRTC in the currently configured mode and then
            calls the CRTC <methodname>page_flip</methodname> operation with a
            pointer to the new frame buffer.
          </para>
          <para>
            The <methodname>page_flip</methodname> operation schedules a page flip.
            Once any pending rendering targeting the new frame buffer has
            completed, the CRTC will be reprogrammed to display that frame buffer
            after the next vertical refresh. The operation must return immediately
            without waiting for rendering or page flip to complete and must block
            any new rendering to the frame buffer until the page flip completes.
          </para>
          <para>
            If a page flip can be successfully scheduled the driver must set the
            <code>drm_crtc-&lt;fb</code> field to the new framebuffer pointed to
            by <code>fb</code>. This is important so that the reference counting
            on framebuffers stays balanced.
          </para>
          <para>
            If a page flip is already pending, the
            <methodname>page_flip</methodname> operation must return
            -<errorname>EBUSY</errorname>.
          </para>
          <para>
            To synchronize page flip to vertical blanking the driver will likely
            need to enable vertical blanking interrupts. It should call
            <function>drm_vblank_get</function> for that purpose, and call
            <function>drm_vblank_put</function> after the page flip completes.
          </para>
          <para>
            If the application has requested to be notified when page flip completes
            the <methodname>page_flip</methodname> operation will be called with a
            non-NULL <parameter>event</parameter> argument pointing to a
            <structname>drm_pending_vblank_event</structname> instance. Upon page
            flip completion the driver must call <methodname>drm_send_vblank_event</methodname>
            to fill in the event and send to wake up any waiting processes.
            This can be performed with
            <programlisting><![CDATA[
            spin_lock_irqsave(&dev->event_lock, flags);
            ...
            drm_send_vblank_event(dev, pipe, event);
            spin_unlock_irqrestore(&dev->event_lock, flags);
            ]]></programlisting>
          </para>
          <note><para>
            FIXME: Could drivers that don't need to wait for rendering to complete
            just add the event to <literal>dev-&gt;vblank_event_list</literal> and
            let the DRM core handle everything, as for "normal" vertical blanking
            events?
          </para></note>
          <para>
            While waiting for the page flip to complete, the
            <literal>event-&gt;base.link</literal> list head can be used freely by
            the driver to store the pending event in a driver-specific list.
          </para>
          <para>
            If the file handle is closed before the event is signaled, drivers must
            take care to destroy the event in their
            <methodname>preclose</methodname> operation (and, if needed, call
            <function>drm_vblank_put</function>).
          </para>
        </sect4>
        <sect4>
          <title>Miscellaneous</title>
          <itemizedlist>
            <listitem>
              <synopsis>void (*set_property)(struct drm_crtc *crtc,
                     struct drm_property *property, uint64_t value);</synopsis>
              <para>
                Set the value of the given CRTC property to
                <parameter>value</parameter>. See <xref linkend="drm-kms-properties"/>
                for more information about properties.
              </para>
            </listitem>
            <listitem>
              <synopsis>void (*gamma_set)(struct drm_crtc *crtc, u16 *r, u16 *g, u16 *b,
                        uint32_t start, uint32_t size);</synopsis>
              <para>
                Apply a gamma table to the device. The operation is optional.
              </para>
            </listitem>
            <listitem>
              <synopsis>void (*destroy)(struct drm_crtc *crtc);</synopsis>
              <para>
                Destroy the CRTC when not needed anymore. See
                <xref linkend="drm-kms-init"/>.
              </para>
            </listitem>
          </itemizedlist>
        </sect4>
      </sect3>
    </sect2>
    <sect2>
      <title>Planes (struct <structname>drm_plane</structname>)</title>
      <para>
        A plane represents an image source that can be blended with or overlayed
        on top of a CRTC during the scanout process. Planes are associated with
        a frame buffer to crop a portion of the image memory (source) and
        optionally scale it to a destination size. The result is then blended
        with or overlayed on top of a CRTC.
      </para>
      <para>
      The DRM core recognizes three types of planes:
      <itemizedlist>
        <listitem>
        DRM_PLANE_TYPE_PRIMARY represents a "main" plane for a CRTC.  Primary
        planes are the planes operated upon by by CRTC modesetting and flipping
        operations described in <xref linkend="drm-kms-crtcops"/>.
        </listitem>
        <listitem>
        DRM_PLANE_TYPE_CURSOR represents a "cursor" plane for a CRTC.  Cursor
        planes are the planes operated upon by the DRM_IOCTL_MODE_CURSOR and
        DRM_IOCTL_MODE_CURSOR2 ioctls.
        </listitem>
        <listitem>
        DRM_PLANE_TYPE_OVERLAY represents all non-primary, non-cursor planes.
        Some drivers refer to these types of planes as "sprites" internally.
        </listitem>
      </itemizedlist>
      For compatibility with legacy userspace, only overlay planes are made
      available to userspace by default.  Userspace clients may set the
      DRM_CLIENT_CAP_UNIVERSAL_PLANES client capability bit to indicate that
      they wish to receive a universal plane list containing all plane types.
      </para>
      <sect3>
        <title>Plane Initialization</title>
        <para>
          To create a plane, a KMS drivers allocates and
          zeroes an instances of struct <structname>drm_plane</structname>
          (possibly as part of a larger structure) and registers it with a call
          to <function>drm_universal_plane_init</function>. The function takes a bitmask
          of the CRTCs that can be associated with the plane, a pointer to the
          plane functions, a list of format supported formats, and the type of
          plane (primary, cursor, or overlay) being initialized.
        </para>
        <para>
          Cursor and overlay planes are optional.  All drivers should provide
          one primary plane per CRTC (although this requirement may change in
          the future); drivers that do not wish to provide special handling for
          primary planes may make use of the helper functions described in
          <xref linkend="drm-kms-planehelpers"/> to create and register a
          primary plane with standard capabilities.
        </para>
      </sect3>
      <sect3>
        <title>Plane Operations</title>
        <itemizedlist>
          <listitem>
            <synopsis>int (*update_plane)(struct drm_plane *plane, struct drm_crtc *crtc,
                        struct drm_framebuffer *fb, int crtc_x, int crtc_y,
                        unsigned int crtc_w, unsigned int crtc_h,
                        uint32_t src_x, uint32_t src_y,
                        uint32_t src_w, uint32_t src_h);</synopsis>
            <para>
              Enable and configure the plane to use the given CRTC and frame buffer.
            </para>
            <para>
              The source rectangle in frame buffer memory coordinates is given by
              the <parameter>src_x</parameter>, <parameter>src_y</parameter>,
              <parameter>src_w</parameter> and <parameter>src_h</parameter>
              parameters (as 16.16 fixed point values). Devices that don't support
              subpixel plane coordinates can ignore the fractional part.
            </para>
            <para>
              The destination rectangle in CRTC coordinates is given by the
              <parameter>crtc_x</parameter>, <parameter>crtc_y</parameter>,
              <parameter>crtc_w</parameter> and <parameter>crtc_h</parameter>
              parameters (as integer values). Devices scale the source rectangle to
              the destination rectangle. If scaling is not supported, and the source
              rectangle size doesn't match the destination rectangle size, the
              driver must return a -<errorname>EINVAL</errorname> error.
            </para>
          </listitem>
          <listitem>
            <synopsis>int (*disable_plane)(struct drm_plane *plane);</synopsis>
            <para>
              Disable the plane. The DRM core calls this method in response to a
              DRM_IOCTL_MODE_SETPLANE ioctl call with the frame buffer ID set to 0.
              Disabled planes must not be processed by the CRTC.
            </para>
          </listitem>
          <listitem>
            <synopsis>void (*destroy)(struct drm_plane *plane);</synopsis>
            <para>
              Destroy the plane when not needed anymore. See
              <xref linkend="drm-kms-init"/>.
            </para>
          </listitem>
        </itemizedlist>
      </sect3>
    </sect2>
    <sect2>
      <title>Encoders (struct <structname>drm_encoder</structname>)</title>
      <para>
        An encoder takes pixel data from a CRTC and converts it to a format
        suitable for any attached connectors. On some devices, it may be
        possible to have a CRTC send data to more than one encoder. In that
        case, both encoders would receive data from the same scanout buffer,
        resulting in a "cloned" display configuration across the connectors
        attached to each encoder.
      </para>
      <sect3>
        <title>Encoder Initialization</title>
        <para>
          As for CRTCs, a KMS driver must create, initialize and register at
          least one struct <structname>drm_encoder</structname> instance. The
          instance is allocated and zeroed by the driver, possibly as part of a
          larger structure.
        </para>
        <para>
          Drivers must initialize the struct <structname>drm_encoder</structname>
          <structfield>possible_crtcs</structfield> and
          <structfield>possible_clones</structfield> fields before registering the
          encoder. Both fields are bitmasks of respectively the CRTCs that the
          encoder can be connected to, and sibling encoders candidate for cloning.
        </para>
        <para>
          After being initialized, the encoder must be registered with a call to
          <function>drm_encoder_init</function>. The function takes a pointer to
          the encoder functions and an encoder type. Supported types are
          <itemizedlist>
            <listitem>
              DRM_MODE_ENCODER_DAC for VGA and analog on DVI-I/DVI-A
              </listitem>
            <listitem>
              DRM_MODE_ENCODER_TMDS for DVI, HDMI and (embedded) DisplayPort
            </listitem>
            <listitem>
              DRM_MODE_ENCODER_LVDS for display panels
            </listitem>
            <listitem>
              DRM_MODE_ENCODER_TVDAC for TV output (Composite, S-Video, Component,
              SCART)
            </listitem>
            <listitem>
              DRM_MODE_ENCODER_VIRTUAL for virtual machine displays
            </listitem>
          </itemizedlist>
        </para>
        <para>
          Encoders must be attached to a CRTC to be used. DRM drivers leave
          encoders unattached at initialization time. Applications (or the fbdev
          compatibility layer when implemented) are responsible for attaching the
          encoders they want to use to a CRTC.
        </para>
      </sect3>
      <sect3>
        <title>Encoder Operations</title>
        <itemizedlist>
          <listitem>
            <synopsis>void (*destroy)(struct drm_encoder *encoder);</synopsis>
            <para>
              Called to destroy the encoder when not needed anymore. See
              <xref linkend="drm-kms-init"/>.
            </para>
          </listitem>
          <listitem>
            <synopsis>void (*set_property)(struct drm_plane *plane,
                     struct drm_property *property, uint64_t value);</synopsis>
            <para>
              Set the value of the given plane property to
              <parameter>value</parameter>. See <xref linkend="drm-kms-properties"/>
              for more information about properties.
            </para>
          </listitem>
        </itemizedlist>
      </sect3>
    </sect2>
    <sect2>
      <title>Connectors (struct <structname>drm_connector</structname>)</title>
      <para>
        A connector is the final destination for pixel data on a device, and
        usually connects directly to an external display device like a monitor
        or laptop panel. A connector can only be attached to one encoder at a
        time. The connector is also the structure where information about the
        attached display is kept, so it contains fields for display data, EDID
        data, DPMS &amp; connection status, and information about modes
        supported on the attached displays.
      </para>
      <sect3>
        <title>Connector Initialization</title>
        <para>
          Finally a KMS driver must create, initialize, register and attach at
          least one struct <structname>drm_connector</structname> instance. The
          instance is created as other KMS objects and initialized by setting the
          following fields.
        </para>
        <variablelist>
          <varlistentry>
            <term><structfield>interlace_allowed</structfield></term>
            <listitem><para>
              Whether the connector can handle interlaced modes.
            </para></listitem>
          </varlistentry>
          <varlistentry>
            <term><structfield>doublescan_allowed</structfield></term>
            <listitem><para>
              Whether the connector can handle doublescan.
            </para></listitem>
          </varlistentry>
          <varlistentry>
            <term><structfield>display_info
            </structfield></term>
            <listitem><para>
              Display information is filled from EDID information when a display
              is detected. For non hot-pluggable displays such as flat panels in
              embedded systems, the driver should initialize the
              <structfield>display_info</structfield>.<structfield>width_mm</structfield>
              and
              <structfield>display_info</structfield>.<structfield>height_mm</structfield>
              fields with the physical size of the display.
            </para></listitem>
          </varlistentry>
          <varlistentry>
            <term id="drm-kms-connector-polled"><structfield>polled</structfield></term>
            <listitem><para>
              Connector polling mode, a combination of
              <variablelist>
                <varlistentry>
                  <term>DRM_CONNECTOR_POLL_HPD</term>
                  <listitem><para>
                    The connector generates hotplug events and doesn't need to be
                    periodically polled. The CONNECT and DISCONNECT flags must not
                    be set together with the HPD flag.
                  </para></listitem>
                </varlistentry>
                <varlistentry>
                  <term>DRM_CONNECTOR_POLL_CONNECT</term>
                  <listitem><para>
                    Periodically poll the connector for connection.
                  </para></listitem>
                </varlistentry>
                <varlistentry>
                  <term>DRM_CONNECTOR_POLL_DISCONNECT</term>
                  <listitem><para>
                    Periodically poll the connector for disconnection.
                  </para></listitem>
                </varlistentry>
              </variablelist>
              Set to 0 for connectors that don't support connection status
              discovery.
            </para></listitem>
          </varlistentry>
        </variablelist>
        <para>
          The connector is then registered with a call to
          <function>drm_connector_init</function> with a pointer to the connector
          functions and a connector type, and exposed through sysfs with a call to
          <function>drm_sysfs_connector_add</function>.
        </para>
        <para>
          Supported connector types are
          <itemizedlist>
            <listitem>DRM_MODE_CONNECTOR_VGA</listitem>
            <listitem>DRM_MODE_CONNECTOR_DVII</listitem>
            <listitem>DRM_MODE_CONNECTOR_DVID</listitem>
            <listitem>DRM_MODE_CONNECTOR_DVIA</listitem>
            <listitem>DRM_MODE_CONNECTOR_Composite</listitem>
            <listitem>DRM_MODE_CONNECTOR_SVIDEO</listitem>
            <listitem>DRM_MODE_CONNECTOR_LVDS</listitem>
            <listitem>DRM_MODE_CONNECTOR_Component</listitem>
            <listitem>DRM_MODE_CONNECTOR_9PinDIN</listitem>
            <listitem>DRM_MODE_CONNECTOR_DisplayPort</listitem>
            <listitem>DRM_MODE_CONNECTOR_HDMIA</listitem>
            <listitem>DRM_MODE_CONNECTOR_HDMIB</listitem>
            <listitem>DRM_MODE_CONNECTOR_TV</listitem>
            <listitem>DRM_MODE_CONNECTOR_eDP</listitem>
            <listitem>DRM_MODE_CONNECTOR_VIRTUAL</listitem>
          </itemizedlist>
        </para>
        <para>
          Connectors must be attached to an encoder to be used. For devices that
          map connectors to encoders 1:1, the connector should be attached at
          initialization time with a call to
          <function>drm_mode_connector_attach_encoder</function>. The driver must
          also set the <structname>drm_connector</structname>
          <structfield>encoder</structfield> field to point to the attached
          encoder.
        </para>
        <para>
          Finally, drivers must initialize the connectors state change detection
          with a call to <function>drm_kms_helper_poll_init</function>. If at
          least one connector is pollable but can't generate hotplug interrupts
          (indicated by the DRM_CONNECTOR_POLL_CONNECT and
          DRM_CONNECTOR_POLL_DISCONNECT connector flags), a delayed work will
          automatically be queued to periodically poll for changes. Connectors
          that can generate hotplug interrupts must be marked with the
          DRM_CONNECTOR_POLL_HPD flag instead, and their interrupt handler must
          call <function>drm_helper_hpd_irq_event</function>. The function will
          queue a delayed work to check the state of all connectors, but no
          periodic polling will be done.
        </para>
      </sect3>
      <sect3>
        <title>Connector Operations</title>
        <note><para>
          Unless otherwise state, all operations are mandatory.
        </para></note>
        <sect4>
          <title>DPMS</title>
          <synopsis>void (*dpms)(struct drm_connector *connector, int mode);</synopsis>
          <para>
            The DPMS operation sets the power state of a connector. The mode
            argument is one of
            <itemizedlist>
              <listitem><para>DRM_MODE_DPMS_ON</para></listitem>
              <listitem><para>DRM_MODE_DPMS_STANDBY</para></listitem>
              <listitem><para>DRM_MODE_DPMS_SUSPEND</para></listitem>
              <listitem><para>DRM_MODE_DPMS_OFF</para></listitem>
            </itemizedlist>
          </para>
          <para>
            In all but DPMS_ON mode the encoder to which the connector is attached
            should put the display in low-power mode by driving its signals
            appropriately. If more than one connector is attached to the encoder
            care should be taken not to change the power state of other displays as
            a side effect. Low-power mode should be propagated to the encoders and
            CRTCs when all related connectors are put in low-power mode.
          </para>
        </sect4>
        <sect4>
          <title>Modes</title>
          <synopsis>int (*fill_modes)(struct drm_connector *connector, uint32_t max_width,
                      uint32_t max_height);</synopsis>
          <para>
            Fill the mode list with all supported modes for the connector. If the
            <parameter>max_width</parameter> and <parameter>max_height</parameter>
            arguments are non-zero, the implementation must ignore all modes wider
            than <parameter>max_width</parameter> or higher than
            <parameter>max_height</parameter>.
          </para>
          <para>
            The connector must also fill in this operation its
            <structfield>display_info</structfield>
            <structfield>width_mm</structfield> and
            <structfield>height_mm</structfield> fields with the connected display
            physical size in millimeters. The fields should be set to 0 if the value
            isn't known or is not applicable (for instance for projector devices).
          </para>
        </sect4>
        <sect4>
          <title>Connection Status</title>
          <para>
            The connection status is updated through polling or hotplug events when
            supported (see <xref linkend="drm-kms-connector-polled"/>). The status
            value is reported to userspace through ioctls and must not be used
            inside the driver, as it only gets initialized by a call to
            <function>drm_mode_getconnector</function> from userspace.
          </para>
          <synopsis>enum drm_connector_status (*detect)(struct drm_connector *connector,
                                        bool force);</synopsis>
          <para>
            Check to see if anything is attached to the connector. The
            <parameter>force</parameter> parameter is set to false whilst polling or
            to true when checking the connector due to user request.
            <parameter>force</parameter> can be used by the driver to avoid
            expensive, destructive operations during automated probing.
          </para>
          <para>
            Return connector_status_connected if something is connected to the
            connector, connector_status_disconnected if nothing is connected and
            connector_status_unknown if the connection state isn't known.
          </para>
          <para>
            Drivers should only return connector_status_connected if the connection
            status has really been probed as connected. Connectors that can't detect
            the connection status, or failed connection status probes, should return
            connector_status_unknown.
          </para>
        </sect4>
        <sect4>
          <title>Miscellaneous</title>
          <itemizedlist>
            <listitem>
              <synopsis>void (*set_property)(struct drm_connector *connector,
                     struct drm_property *property, uint64_t value);</synopsis>
              <para>
                Set the value of the given connector property to
                <parameter>value</parameter>. See <xref linkend="drm-kms-properties"/>
                for more information about properties.
              </para>
            </listitem>
            <listitem>
              <synopsis>void (*destroy)(struct drm_connector *connector);</synopsis>
              <para>
                Destroy the connector when not needed anymore. See
                <xref linkend="drm-kms-init"/>.
              </para>
            </listitem>
          </itemizedlist>
        </sect4>
      </sect3>
    </sect2>
    <sect2>
      <title>Cleanup</title>
      <para>
        The DRM core manages its objects' lifetime. When an object is not needed
        anymore the core calls its destroy function, which must clean up and
        free every resource allocated for the object. Every
        <function>drm_*_init</function> call must be matched with a
        corresponding <function>drm_*_cleanup</function> call to cleanup CRTCs
        (<function>drm_crtc_cleanup</function>), planes
        (<function>drm_plane_cleanup</function>), encoders
        (<function>drm_encoder_cleanup</function>) and connectors
        (<function>drm_connector_cleanup</function>). Furthermore, connectors
        that have been added to sysfs must be removed by a call to
        <function>drm_sysfs_connector_remove</function> before calling
        <function>drm_connector_cleanup</function>.
      </para>
      <para>
        Connectors state change detection must be cleanup up with a call to
        <function>drm_kms_helper_poll_fini</function>.
      </para>
    </sect2>
    <sect2>
      <title>Output discovery and initialization example</title>
      <programlisting><![CDATA[
void intel_crt_init(struct drm_device *dev)
{
        struct drm_connector *connector;
        struct intel_output *intel_output;

        intel_output = kzalloc(sizeof(struct intel_output), GFP_KERNEL);
        if (!intel_output)
                return;

        connector = &intel_output->base;
        drm_connector_init(dev, &intel_output->base,
                           &intel_crt_connector_funcs, DRM_MODE_CONNECTOR_VGA);

        drm_encoder_init(dev, &intel_output->enc, &intel_crt_enc_funcs,
                         DRM_MODE_ENCODER_DAC);

        drm_mode_connector_attach_encoder(&intel_output->base,
                                          &intel_output->enc);

        /* Set up the DDC bus. */
        intel_output->ddc_bus = intel_i2c_create(dev, GPIOA, "CRTDDC_A");
        if (!intel_output->ddc_bus) {
                dev_printk(KERN_ERR, &dev->pdev->dev, "DDC bus registration "
                           "failed.\n");
                return;
        }

        intel_output->type = INTEL_OUTPUT_ANALOG;
        connector->interlace_allowed = 0;
        connector->doublescan_allowed = 0;

        drm_encoder_helper_add(&intel_output->enc, &intel_crt_helper_funcs);
        drm_connector_helper_add(connector, &intel_crt_connector_helper_funcs);

        drm_sysfs_connector_add(connector);
}]]></programlisting>
      <para>
        In the example above (taken from the i915 driver), a CRTC, connector and
        encoder combination is created. A device-specific i2c bus is also
        created for fetching EDID data and performing monitor detection. Once
        the process is complete, the new connector is registered with sysfs to
        make its properties available to applications.
      </para>
    </sect2>
    <sect2>
      <title>KMS API Functions</title>
!Edrivers/gpu/drm/drm_crtc.c
    </sect2>
    <sect2>
      <title>KMS Locking</title>
!Pdrivers/gpu/drm/drm_modeset_lock.c kms locking
!Iinclude/drm/drm_modeset_lock.h
!Edrivers/gpu/drm/drm_modeset_lock.c
    </sect2>
  </sect1>

  <!-- Internals: kms helper functions -->

  <sect1>
    <title>Mode Setting Helper Functions</title>
    <para>
      The plane, CRTC, encoder and connector functions provided by the drivers
      implement the DRM API. They're called by the DRM core and ioctl handlers
      to handle device state changes and configuration request. As implementing
      those functions often requires logic not specific to drivers, mid-layer
      helper functions are available to avoid duplicating boilerplate code.
    </para>
    <para>
      The DRM core contains one mid-layer implementation. The mid-layer provides
      implementations of several plane, CRTC, encoder and connector functions
      (called from the top of the mid-layer) that pre-process requests and call
      lower-level functions provided by the driver (at the bottom of the
      mid-layer). For instance, the
      <function>drm_crtc_helper_set_config</function> function can be used to
      fill the struct <structname>drm_crtc_funcs</structname>
      <structfield>set_config</structfield> field. When called, it will split
      the <methodname>set_config</methodname> operation in smaller, simpler
      operations and call the driver to handle them.
    </para>
    <para>
      To use the mid-layer, drivers call <function>drm_crtc_helper_add</function>,
      <function>drm_encoder_helper_add</function> and
      <function>drm_connector_helper_add</function> functions to install their
      mid-layer bottom operations handlers, and fill the
      <structname>drm_crtc_funcs</structname>,
      <structname>drm_encoder_funcs</structname> and
      <structname>drm_connector_funcs</structname> structures with pointers to
      the mid-layer top API functions. Installing the mid-layer bottom operation
      handlers is best done right after registering the corresponding KMS object.
    </para>
    <para>
      The mid-layer is not split between CRTC, encoder and connector operations.
      To use it, a driver must provide bottom functions for all of the three KMS
      entities.
    </para>
    <sect2>
      <title>Helper Functions</title>
      <itemizedlist>
        <listitem>
          <synopsis>int drm_crtc_helper_set_config(struct drm_mode_set *set);</synopsis>
          <para>
            The <function>drm_crtc_helper_set_config</function> helper function
            is a CRTC <methodname>set_config</methodname> implementation. It
            first tries to locate the best encoder for each connector by calling
            the connector <methodname>best_encoder</methodname> helper
            operation.
          </para>
          <para>
            After locating the appropriate encoders, the helper function will
            call the <methodname>mode_fixup</methodname> encoder and CRTC helper
            operations to adjust the requested mode, or reject it completely in
            which case an error will be returned to the application. If the new
            configuration after mode adjustment is identical to the current
            configuration the helper function will return without performing any
            other operation.
          </para>
          <para>
            If the adjusted mode is identical to the current mode but changes to
            the frame buffer need to be applied, the
            <function>drm_crtc_helper_set_config</function> function will call
            the CRTC <methodname>mode_set_base</methodname> helper operation. If
            the adjusted mode differs from the current mode, or if the
            <methodname>mode_set_base</methodname> helper operation is not
            provided, the helper function performs a full mode set sequence by
            calling the <methodname>prepare</methodname>,
            <methodname>mode_set</methodname> and
            <methodname>commit</methodname> CRTC and encoder helper operations,
            in that order.
          </para>
        </listitem>
        <listitem>
          <synopsis>void drm_helper_connector_dpms(struct drm_connector *connector, int mode);</synopsis>
          <para>
            The <function>drm_helper_connector_dpms</function> helper function
            is a connector <methodname>dpms</methodname> implementation that
            tracks power state of connectors. To use the function, drivers must
            provide <methodname>dpms</methodname> helper operations for CRTCs
            and encoders to apply the DPMS state to the device.
          </para>
          <para>
            The mid-layer doesn't track the power state of CRTCs and encoders.
            The <methodname>dpms</methodname> helper operations can thus be
            called with a mode identical to the currently active mode.
          </para>
        </listitem>
        <listitem>
          <synopsis>int drm_helper_probe_single_connector_modes(struct drm_connector *connector,
                                            uint32_t maxX, uint32_t maxY);</synopsis>
          <para>
            The <function>drm_helper_probe_single_connector_modes</function> helper
            function is a connector <methodname>fill_modes</methodname>
            implementation that updates the connection status for the connector
            and then retrieves a list of modes by calling the connector
            <methodname>get_modes</methodname> helper operation.
          </para>
          <para>
            The function filters out modes larger than
            <parameter>max_width</parameter> and <parameter>max_height</parameter>
            if specified. It then calls the optional connector
            <methodname>mode_valid</methodname> helper operation for each mode in
            the probed list to check whether the mode is valid for the connector.
          </para>
        </listitem>
      </itemizedlist>
    </sect2>
    <sect2>
      <title>CRTC Helper Operations</title>
      <itemizedlist>
        <listitem id="drm-helper-crtc-mode-fixup">
          <synopsis>bool (*mode_fixup)(struct drm_crtc *crtc,
                       const struct drm_display_mode *mode,
                       struct drm_display_mode *adjusted_mode);</synopsis>
          <para>
            Let CRTCs adjust the requested mode or reject it completely. This
            operation returns true if the mode is accepted (possibly after being
            adjusted) or false if it is rejected.
          </para>
          <para>
            The <methodname>mode_fixup</methodname> operation should reject the
            mode if it can't reasonably use it. The definition of "reasonable"
            is currently fuzzy in this context. One possible behaviour would be
            to set the adjusted mode to the panel timings when a fixed-mode
            panel is used with hardware capable of scaling. Another behaviour
            would be to accept any input mode and adjust it to the closest mode
            supported by the hardware (FIXME: This needs to be clarified).
          </para>
        </listitem>
        <listitem>
          <synopsis>int (*mode_set_base)(struct drm_crtc *crtc, int x, int y,
                     struct drm_framebuffer *old_fb)</synopsis>
          <para>
            Move the CRTC on the current frame buffer (stored in
            <literal>crtc-&gt;fb</literal>) to position (x,y). Any of the frame
            buffer, x position or y position may have been modified.
          </para>
          <para>
            This helper operation is optional. If not provided, the
            <function>drm_crtc_helper_set_config</function> function will fall
            back to the <methodname>mode_set</methodname> helper operation.
          </para>
          <note><para>
            FIXME: Why are x and y passed as arguments, as they can be accessed
            through <literal>crtc-&gt;x</literal> and
            <literal>crtc-&gt;y</literal>?
          </para></note>
        </listitem>
        <listitem>
          <synopsis>void (*prepare)(struct drm_crtc *crtc);</synopsis>
          <para>
            Prepare the CRTC for mode setting. This operation is called after
            validating the requested mode. Drivers use it to perform
            device-specific operations required before setting the new mode.
          </para>
        </listitem>
        <listitem>
          <synopsis>int (*mode_set)(struct drm_crtc *crtc, struct drm_display_mode *mode,
                struct drm_display_mode *adjusted_mode, int x, int y,
                struct drm_framebuffer *old_fb);</synopsis>
          <para>
            Set a new mode, position and frame buffer. Depending on the device
            requirements, the mode can be stored internally by the driver and
            applied in the <methodname>commit</methodname> operation, or
            programmed to the hardware immediately.
          </para>
          <para>
            The <methodname>mode_set</methodname> operation returns 0 on success
            or a negative error code if an error occurs.
          </para>
        </listitem>
        <listitem>
          <synopsis>void (*commit)(struct drm_crtc *crtc);</synopsis>
          <para>
            Commit a mode. This operation is called after setting the new mode.
            Upon return the device must use the new mode and be fully
            operational.
          </para>
        </listitem>
      </itemizedlist>
    </sect2>
    <sect2>
      <title>Encoder Helper Operations</title>
      <itemizedlist>
        <listitem>
          <synopsis>bool (*mode_fixup)(struct drm_encoder *encoder,
                       const struct drm_display_mode *mode,
                       struct drm_display_mode *adjusted_mode);</synopsis>
          <para>
            Let encoders adjust the requested mode or reject it completely. This
            operation returns true if the mode is accepted (possibly after being
            adjusted) or false if it is rejected. See the
            <link linkend="drm-helper-crtc-mode-fixup">mode_fixup CRTC helper
            operation</link> for an explanation of the allowed adjustments.
          </para>
        </listitem>
        <listitem>
          <synopsis>void (*prepare)(struct drm_encoder *encoder);</synopsis>
          <para>
            Prepare the encoder for mode setting. This operation is called after
            validating the requested mode. Drivers use it to perform
            device-specific operations required before setting the new mode.
          </para>
        </listitem>
        <listitem>
          <synopsis>void (*mode_set)(struct drm_encoder *encoder,
                 struct drm_display_mode *mode,
                 struct drm_display_mode *adjusted_mode);</synopsis>
          <para>
            Set a new mode. Depending on the device requirements, the mode can
            be stored internally by the driver and applied in the
            <methodname>commit</methodname> operation, or programmed to the
            hardware immediately.
          </para>
        </listitem>
        <listitem>
          <synopsis>void (*commit)(struct drm_encoder *encoder);</synopsis>
          <para>
            Commit a mode. This operation is called after setting the new mode.
            Upon return the device must use the new mode and be fully
            operational.
          </para>
        </listitem>
      </itemizedlist>
    </sect2>
    <sect2>
      <title>Connector Helper Operations</title>
      <itemizedlist>
        <listitem>
          <synopsis>struct drm_encoder *(*best_encoder)(struct drm_connector *connector);</synopsis>
          <para>
            Return a pointer to the best encoder for the connecter. Device that
            map connectors to encoders 1:1 simply return the pointer to the
            associated encoder. This operation is mandatory.
          </para>
        </listitem>
        <listitem>
          <synopsis>int (*get_modes)(struct drm_connector *connector);</synopsis>
          <para>
            Fill the connector's <structfield>probed_modes</structfield> list
            by parsing EDID data with <function>drm_add_edid_modes</function> or
            calling <function>drm_mode_probed_add</function> directly for every
            supported mode and return the number of modes it has detected. This
            operation is mandatory.
          </para>
          <para>
            When adding modes manually the driver creates each mode with a call to
            <function>drm_mode_create</function> and must fill the following fields.
            <itemizedlist>
              <listitem>
                <synopsis>__u32 type;</synopsis>
                <para>
                  Mode type bitmask, a combination of
                  <variablelist>
                    <varlistentry>
                      <term>DRM_MODE_TYPE_BUILTIN</term>
                      <listitem><para>not used?</para></listitem>
                    </varlistentry>
                    <varlistentry>
                      <term>DRM_MODE_TYPE_CLOCK_C</term>
                      <listitem><para>not used?</para></listitem>
                    </varlistentry>
                    <varlistentry>
                      <term>DRM_MODE_TYPE_CRTC_C</term>
                      <listitem><para>not used?</para></listitem>
                    </varlistentry>
                    <varlistentry>
                      <term>
        DRM_MODE_TYPE_PREFERRED - The preferred mode for the connector
                      </term>
                      <listitem>
                        <para>not used?</para>
                      </listitem>
                    </varlistentry>
                    <varlistentry>
                      <term>DRM_MODE_TYPE_DEFAULT</term>
                      <listitem><para>not used?</para></listitem>
                    </varlistentry>
                    <varlistentry>
                      <term>DRM_MODE_TYPE_USERDEF</term>
                      <listitem><para>not used?</para></listitem>
                    </varlistentry>
                    <varlistentry>
                      <term>DRM_MODE_TYPE_DRIVER</term>
                      <listitem>
                        <para>
                          The mode has been created by the driver (as opposed to
                          to user-created modes).
                        </para>
                      </listitem>
                    </varlistentry>
                  </variablelist>
                  Drivers must set the DRM_MODE_TYPE_DRIVER bit for all modes they
                  create, and set the DRM_MODE_TYPE_PREFERRED bit for the preferred
                  mode.
                </para>
              </listitem>
              <listitem>
                <synopsis>__u32 clock;</synopsis>
                <para>Pixel clock frequency in kHz unit</para>
              </listitem>
              <listitem>
                <synopsis>__u16 hdisplay, hsync_start, hsync_end, htotal;
    __u16 vdisplay, vsync_start, vsync_end, vtotal;</synopsis>
                <para>Horizontal and vertical timing information</para>
                <screen><![CDATA[
             Active                 Front           Sync           Back
             Region                 Porch                          Porch
    <-----------------------><----------------><-------------><-------------->

      //////////////////////|
     ////////////////////// |
    //////////////////////  |..................               ................
                                               _______________

    <----- [hv]display ----->
    <------------- [hv]sync_start ------------>
    <--------------------- [hv]sync_end --------------------->
    <-------------------------------- [hv]total ----------------------------->
]]></screen>
              </listitem>
              <listitem>
                <synopsis>__u16 hskew;
    __u16 vscan;</synopsis>
                <para>Unknown</para>
              </listitem>
              <listitem>
                <synopsis>__u32 flags;</synopsis>
                <para>
                  Mode flags, a combination of
                  <variablelist>
                    <varlistentry>
                      <term>DRM_MODE_FLAG_PHSYNC</term>
                      <listitem><para>
                        Horizontal sync is active high
                      </para></listitem>
                    </varlistentry>
                    <varlistentry>
                      <term>DRM_MODE_FLAG_NHSYNC</term>
                      <listitem><para>
                        Horizontal sync is active low
                      </para></listitem>
                    </varlistentry>
                    <varlistentry>
                      <term>DRM_MODE_FLAG_PVSYNC</term>
                      <listitem><para>
                        Vertical sync is active high
                      </para></listitem>
                    </varlistentry>
                    <varlistentry>
                      <term>DRM_MODE_FLAG_NVSYNC</term>
                      <listitem><para>
                        Vertical sync is active low
                      </para></listitem>
                    </varlistentry>
                    <varlistentry>
                      <term>DRM_MODE_FLAG_INTERLACE</term>
                      <listitem><para>
                        Mode is interlaced
                      </para></listitem>
                    </varlistentry>
                    <varlistentry>
                      <term>DRM_MODE_FLAG_DBLSCAN</term>
                      <listitem><para>
                        Mode uses doublescan
                      </para></listitem>
                    </varlistentry>
                    <varlistentry>
                      <term>DRM_MODE_FLAG_CSYNC</term>
                      <listitem><para>
                        Mode uses composite sync
                      </para></listitem>
                    </varlistentry>
                    <varlistentry>
                      <term>DRM_MODE_FLAG_PCSYNC</term>
                      <listitem><para>
                        Composite sync is active high
                      </para></listitem>
                    </varlistentry>
                    <varlistentry>
                      <term>DRM_MODE_FLAG_NCSYNC</term>
                      <listitem><para>
                        Composite sync is active low
                      </para></listitem>
                    </varlistentry>
                    <varlistentry>
                      <term>DRM_MODE_FLAG_HSKEW</term>
                      <listitem><para>
                        hskew provided (not used?)
                      </para></listitem>
                    </varlistentry>
                    <varlistentry>
                      <term>DRM_MODE_FLAG_BCAST</term>
                      <listitem><para>
                        not used?
                      </para></listitem>
                    </varlistentry>
                    <varlistentry>
                      <term>DRM_MODE_FLAG_PIXMUX</term>
                      <listitem><para>
                        not used?
                      </para></listitem>
                    </varlistentry>
                    <varlistentry>
                      <term>DRM_MODE_FLAG_DBLCLK</term>
                      <listitem><para>
                        not used?
                      </para></listitem>
                    </varlistentry>
                    <varlistentry>
                      <term>DRM_MODE_FLAG_CLKDIV2</term>
                      <listitem><para>
                        ?
                      </para></listitem>
                    </varlistentry>
                  </variablelist>
                </para>
                <para>
                  Note that modes marked with the INTERLACE or DBLSCAN flags will be
                  filtered out by
                  <function>drm_helper_probe_single_connector_modes</function> if
                  the connector's <structfield>interlace_allowed</structfield> or
                  <structfield>doublescan_allowed</structfield> field is set to 0.
                </para>
              </listitem>
              <listitem>
                <synopsis>char name[DRM_DISPLAY_MODE_LEN];</synopsis>
                <para>
                  Mode name. The driver must call
                  <function>drm_mode_set_name</function> to fill the mode name from
                  <structfield>hdisplay</structfield>,
                  <structfield>vdisplay</structfield> and interlace flag after
                  filling the corresponding fields.
                </para>
              </listitem>
            </itemizedlist>
          </para>
          <para>
            The <structfield>vrefresh</structfield> value is computed by
            <function>drm_helper_probe_single_connector_modes</function>.
          </para>
          <para>
            When parsing EDID data, <function>drm_add_edid_modes</function> fill the
            connector <structfield>display_info</structfield>
            <structfield>width_mm</structfield> and
            <structfield>height_mm</structfield> fields. When creating modes
            manually the <methodname>get_modes</methodname> helper operation must
            set the <structfield>display_info</structfield>
            <structfield>width_mm</structfield> and
            <structfield>height_mm</structfield> fields if they haven't been set
            already (for instance at initialization time when a fixed-size panel is
            attached to the connector). The mode <structfield>width_mm</structfield>
            and <structfield>height_mm</structfield> fields are only used internally
            during EDID parsing and should not be set when creating modes manually.
          </para>
        </listitem>
        <listitem>
          <synopsis>int (*mode_valid)(struct drm_connector *connector,
                  struct drm_display_mode *mode);</synopsis>
          <para>
            Verify whether a mode is valid for the connector. Return MODE_OK for
            supported modes and one of the enum drm_mode_status values (MODE_*)
            for unsupported modes. This operation is optional.
          </para>
          <para>
            As the mode rejection reason is currently not used beside for
            immediately removing the unsupported mode, an implementation can
            return MODE_BAD regardless of the exact reason why the mode is not
            valid.
          </para>
          <note><para>
            Note that the <methodname>mode_valid</methodname> helper operation is
            only called for modes detected by the device, and
            <emphasis>not</emphasis> for modes set by the user through the CRTC
            <methodname>set_config</methodname> operation.
          </para></note>
        </listitem>
      </itemizedlist>
    </sect2>
    <sect2>
      <title>Modeset Helper Functions Reference</title>
!Edrivers/gpu/drm/drm_crtc_helper.c
    </sect2>
    <sect2>
      <title>Output Probing Helper Functions Reference</title>
!Pdrivers/gpu/drm/drm_probe_helper.c output probing helper overview
!Edrivers/gpu/drm/drm_probe_helper.c
    </sect2>
    <sect2>
      <title>fbdev Helper Functions Reference</title>
!Pdrivers/gpu/drm/drm_fb_helper.c fbdev helpers
!Edrivers/gpu/drm/drm_fb_helper.c
!Iinclude/drm/drm_fb_helper.h
    </sect2>
    <sect2>
      <title>Display Port Helper Functions Reference</title>
!Pdrivers/gpu/drm/drm_dp_helper.c dp helpers
!Iinclude/drm/drm_dp_helper.h
!Edrivers/gpu/drm/drm_dp_helper.c
    </sect2>
    <sect2>
      <title>EDID Helper Functions Reference</title>
!Edrivers/gpu/drm/drm_edid.c
    </sect2>
    <sect2>
      <title>Rectangle Utilities Reference</title>
!Pinclude/drm/drm_rect.h rect utils
!Iinclude/drm/drm_rect.h
!Edrivers/gpu/drm/drm_rect.c
    </sect2>
    <sect2>
      <title>Flip-work Helper Reference</title>
!Pinclude/drm/drm_flip_work.h flip utils
!Iinclude/drm/drm_flip_work.h
!Edrivers/gpu/drm/drm_flip_work.c
    </sect2>
    <sect2>
      <title>HDMI Infoframes Helper Reference</title>
      <para>
        Strictly speaking this is not a DRM helper library but generally useable
        by any driver interfacing with HDMI outputs like v4l or alsa drivers.
        But it nicely fits into the overall topic of mode setting helper
        libraries and hence is also included here.
      </para>
!Iinclude/linux/hdmi.h
!Edrivers/video/hdmi.c
    </sect2>
    <sect2>
      <title id="drm-kms-planehelpers">Plane Helper Reference</title>
!Edrivers/gpu/drm/drm_plane_helper.c Plane Helpers
    </sect2>
  </sect1>

  <!-- Internals: kms properties -->

  <sect1 id="drm-kms-properties">
    <title>KMS Properties</title>
    <para>
      Drivers may need to expose additional parameters to applications than
      those described in the previous sections. KMS supports attaching
      properties to CRTCs, connectors and planes and offers a userspace API to
      list, get and set the property values.
    </para>
    <para>
      Properties are identified by a name that uniquely defines the property
      purpose, and store an associated value. For all property types except blob
      properties the value is a 64-bit unsigned integer.
    </para>
    <para>
      KMS differentiates between properties and property instances. Drivers
      first create properties and then create and associate individual instances
      of those properties to objects. A property can be instantiated multiple
      times and associated with different objects. Values are stored in property
      instances, and all other property information are stored in the property
      and shared between all instances of the property.
    </para>
    <para>
      Every property is created with a type that influences how the KMS core
      handles the property. Supported property types are
      <variablelist>
        <varlistentry>
          <term>DRM_MODE_PROP_RANGE</term>
          <listitem><para>Range properties report their minimum and maximum
            admissible values. The KMS core verifies that values set by
            application fit in that range.</para></listitem>
        </varlistentry>
        <varlistentry>
          <term>DRM_MODE_PROP_ENUM</term>
          <listitem><para>Enumerated properties take a numerical value that
            ranges from 0 to the number of enumerated values defined by the
            property minus one, and associate a free-formed string name to each
            value. Applications can retrieve the list of defined value-name pairs
            and use the numerical value to get and set property instance values.
            </para></listitem>
        </varlistentry>
        <varlistentry>
          <term>DRM_MODE_PROP_BITMASK</term>
          <listitem><para>Bitmask properties are enumeration properties that
            additionally restrict all enumerated values to the 0..63 range.
            Bitmask property instance values combine one or more of the
            enumerated bits defined by the property.</para></listitem>
        </varlistentry>
        <varlistentry>
          <term>DRM_MODE_PROP_BLOB</term>
          <listitem><para>Blob properties store a binary blob without any format
            restriction. The binary blobs are created as KMS standalone objects,
            and blob property instance values store the ID of their associated
            blob object.</para>
            <para>Blob properties are only used for the connector EDID property
            and cannot be created by drivers.</para></listitem>
        </varlistentry>
      </variablelist>
    </para>
    <para>
      To create a property drivers call one of the following functions depending
      on the property type. All property creation functions take property flags
      and name, as well as type-specific arguments.
      <itemizedlist>
        <listitem>
          <synopsis>struct drm_property *drm_property_create_range(struct drm_device *dev, int flags,
                                               const char *name,
                                               uint64_t min, uint64_t max);</synopsis>
          <para>Create a range property with the given minimum and maximum
            values.</para>
        </listitem>
        <listitem>
          <synopsis>struct drm_property *drm_property_create_enum(struct drm_device *dev, int flags,
                                              const char *name,
                                              const struct drm_prop_enum_list *props,
                                              int num_values);</synopsis>
          <para>Create an enumerated property. The <parameter>props</parameter>
            argument points to an array of <parameter>num_values</parameter>
            value-name pairs.</para>
        </listitem>
        <listitem>
          <synopsis>struct drm_property *drm_property_create_bitmask(struct drm_device *dev,
                                                 int flags, const char *name,
                                                 const struct drm_prop_enum_list *props,
                                                 int num_values);</synopsis>
          <para>Create a bitmask property. The <parameter>props</parameter>
            argument points to an array of <parameter>num_values</parameter>
            value-name pairs.</para>
        </listitem>
      </itemizedlist>
    </para>
    <para>
      Properties can additionally be created as immutable, in which case they
      will be read-only for applications but can be modified by the driver. To
      create an immutable property drivers must set the DRM_MODE_PROP_IMMUTABLE
      flag at property creation time.
    </para>
    <para>
      When no array of value-name pairs is readily available at property
      creation time for enumerated or range properties, drivers can create
      the property using the <function>drm_property_create</function> function
      and manually add enumeration value-name pairs by calling the
      <function>drm_property_add_enum</function> function. Care must be taken to
      properly specify the property type through the <parameter>flags</parameter>
      argument.
    </para>
    <para>
      After creating properties drivers can attach property instances to CRTC,
      connector and plane objects by calling the
      <function>drm_object_attach_property</function>. The function takes a
      pointer to the target object, a pointer to the previously created property
      and an initial instance value.
    </para>
    <sect2>
        <title>Existing KMS Properties</title>
        <para>
        The following table gives description of drm properties exposed by various
        modules/drivers.
        </para>
        <table border="1" cellpadding="0" cellspacing="0">
        <tbody>
        <tr style="font-weight: bold;">
        <td valign="top" >Owner Module/Drivers</td>
        <td valign="top" >Group</td>
        <td valign="top" >Property Name</td>
        <td valign="top" >Type</td>
        <td valign="top" >Property Values</td>
        <td valign="top" >Object attached</td>
        <td valign="top" >Description/Restrictions</td>
        </tr>
        <tr>
        <td rowspan="20" valign="top" >DRM</td>
        <td rowspan="2" valign="top" >Generic</td>
        <td valign="top" >“EDID”</td>
        <td valign="top" >BLOB | IMMUTABLE</td>
        <td valign="top" >0</td>
        <td valign="top" >Connector</td>
        <td valign="top" >Contains id of edid blob ptr object.</td>
        </tr>
        <tr>
        <td valign="top" >“DPMS”</td>
        <td valign="top" >ENUM</td>
        <td valign="top" >{ “On”, “Standby”, “Suspend”, “Off” }</td>
        <td valign="top" >Connector</td>
        <td valign="top" >Contains DPMS operation mode value.</td>
        </tr>
        <tr>
        <td rowspan="1" valign="top" >Plane</td>
        <td valign="top" >“type”</td>
        <td valign="top" >ENUM | IMMUTABLE</td>
        <td valign="top" >{ "Overlay", "Primary", "Cursor" }</td>
        <td valign="top" >Plane</td>
        <td valign="top" >Plane type</td>
        </tr>
        <tr>
        <td rowspan="2" valign="top" >DVI-I</td>
        <td valign="top" >“subconnector”</td>
        <td valign="top" >ENUM</td>
        <td valign="top" >{ “Unknown”, “DVI-D”, “DVI-A” }</td>
        <td valign="top" >Connector</td>
        <td valign="top" >TBD</td>
        </tr>
        <tr>
        <td valign="top" >“select subconnector”</td>
        <td valign="top" >ENUM</td>
        <td valign="top" >{ “Automatic”, “DVI-D”, “DVI-A” }</td>
        <td valign="top" >Connector</td>
        <td valign="top" >TBD</td>
        </tr>
        <tr>
        <td rowspan="13" valign="top" >TV</td>
        <td valign="top" >“subconnector”</td>
        <td valign="top" >ENUM</td>
        <td valign="top" >{ "Unknown", "Composite", "SVIDEO", "Component", "SCART" }</td>
        <td valign="top" >Connector</td>
        <td valign="top" >TBD</td>
        </tr>
        <tr>
        <td valign="top" >“select subconnector”</td>
        <td valign="top" >ENUM</td>
        <td valign="top" >{ "Automatic", "Composite", "SVIDEO", "Component", "SCART" }</td>
        <td valign="top" >Connector</td>
        <td valign="top" >TBD</td>
        </tr>
        <tr>
        <td valign="top" >“mode”</td>
        <td valign="top" >ENUM</td>
        <td valign="top" >{ "NTSC_M", "NTSC_J", "NTSC_443", "PAL_B" } etc.</td>
        <td valign="top" >Connector</td>
        <td valign="top" >TBD</td>
        </tr>
        <tr>
        <td valign="top" >“left margin”</td>
        <td valign="top" >RANGE</td>
        <td valign="top" >Min=0, Max=100</td>
        <td valign="top" >Connector</td>
        <td valign="top" >TBD</td>
        </tr>
        <tr>
        <td valign="top" >“right margin”</td>
        <td valign="top" >RANGE</td>
        <td valign="top" >Min=0, Max=100</td>
        <td valign="top" >Connector</td>
        <td valign="top" >TBD</td>
        </tr>
        <tr>
        <td valign="top" >“top margin”</td>
        <td valign="top" >RANGE</td>
        <td valign="top" >Min=0, Max=100</td>
        <td valign="top" >Connector</td>
        <td valign="top" >TBD</td>
        </tr>
        <tr>
        <td valign="top" >“bottom margin”</td>
        <td valign="top" >RANGE</td>
        <td valign="top" >Min=0, Max=100</td>
        <td valign="top" >Connector</td>
        <td valign="top" >TBD</td>
        </tr>
        <tr>
        <td valign="top" >“brightness”</td>
        <td valign="top" >RANGE</td>
        <td valign="top" >Min=0, Max=100</td>
        <td valign="top" >Connector</td>
        <td valign="top" >TBD</td>
        </tr>
        <tr>
        <td valign="top" >“contrast”</td>
        <td valign="top" >RANGE</td>
        <td valign="top" >Min=0, Max=100</td>
        <td valign="top" >Connector</td>
        <td valign="top" >TBD</td>
        </tr>
        <tr>
        <td valign="top" >“flicker reduction”</td>
        <td valign="top" >RANGE</td>
        <td valign="top" >Min=0, Max=100</td>
        <td valign="top" >Connector</td>
        <td valign="top" >TBD</td>
        </tr>
        <tr>
        <td valign="top" >“overscan”</td>
        <td valign="top" >RANGE</td>
        <td valign="top" >Min=0, Max=100</td>
        <td valign="top" >Connector</td>
        <td valign="top" >TBD</td>
        </tr>
        <tr>
        <td valign="top" >“saturation”</td>
        <td valign="top" >RANGE</td>
        <td valign="top" >Min=0, Max=100</td>
        <td valign="top" >Connector</td>
        <td valign="top" >TBD</td>
        </tr>
        <tr>
        <td valign="top" >“hue”</td>
        <td valign="top" >RANGE</td>
        <td valign="top" >Min=0, Max=100</td>
        <td valign="top" >Connector</td>
        <td valign="top" >TBD</td>
        </tr>
        <tr>
        <td rowspan="2" valign="top" >Optional</td>
        <td valign="top" >“scaling mode”</td>
        <td valign="top" >ENUM</td>
        <td valign="top" >{ "None", "Full", "Center", "Full aspect" }</td>
        <td valign="top" >Connector</td>
        <td valign="top" >TBD</td>
        </tr>
        <tr>
        <td valign="top" >“dirty”</td>
        <td valign="top" >ENUM | IMMUTABLE</td>
        <td valign="top" >{ "Off", "On", "Annotate" }</td>
        <td valign="top" >Connector</td>
        <td valign="top" >TBD</td>
        </tr>
        <tr>
        <td rowspan="21" valign="top" >i915</td>
        <td rowspan="3" valign="top" >Generic</td>
        <td valign="top" >"Broadcast RGB"</td>
        <td valign="top" >ENUM</td>
        <td valign="top" >{ "Automatic", "Full", "Limited 16:235" }</td>
        <td valign="top" >Connector</td>
        <td valign="top" >TBD</td>
        </tr>
        <tr>
        <td valign="top" >“audio”</td>
        <td valign="top" >ENUM</td>
        <td valign="top" >{ "force-dvi", "off", "auto", "on" }</td>
        <td valign="top" >Connector</td>
        <td valign="top" >TBD</td>
        </tr>
        <tr>
        <td valign="top" >Standard name as in DRM</td>
        <td valign="top" >Standard type as in DRM</td>
        <td valign="top" >Standard value as in DRM</td>
        <td valign="top" >Standard Object as in DRM</td>
        <td valign="top" >TBD</td>
        </tr>
        <tr>
        <td rowspan="17" valign="top" >SDVO-TV</td>
        <td valign="top" >“mode”</td>
        <td valign="top" >ENUM</td>
        <td valign="top" >{ "NTSC_M", "NTSC_J", "NTSC_443", "PAL_B" } etc.</td>
        <td valign="top" >Connector</td>
        <td valign="top" >TBD</td>
        </tr>
        <tr>
        <td valign="top" >"left_margin"</td>
        <td valign="top" >RANGE</td>
        <td valign="top" >Min=0, Max= SDVO dependent</td>
        <td valign="top" >Connector</td>
        <td valign="top" >TBD</td>
        </tr>
        <tr>
        <td valign="top" >"right_margin"</td>
        <td valign="top" >RANGE</td>
        <td valign="top" >Min=0, Max= SDVO dependent</td>
        <td valign="top" >Connector</td>
        <td valign="top" >TBD</td>
        </tr>
        <tr>
        <td valign="top" >"top_margin"</td>
        <td valign="top" >RANGE</td>
        <td valign="top" >Min=0, Max= SDVO dependent</td>
        <td valign="top" >Connector</td>
        <td valign="top" >TBD</td>
        </tr>
        <tr>
        <td valign="top" >"bottom_margin"</td>
        <td valign="top" >RANGE</td>
        <td valign="top" >Min=0, Max= SDVO dependent</td>
        <td valign="top" >Connector</td>
        <td valign="top" >TBD</td>
        </tr>
        <tr>
        <td valign="top" >“hpos”</td>
        <td valign="top" >RANGE</td>
        <td valign="top" >Min=0, Max= SDVO dependent</td>
        <td valign="top" >Connector</td>
        <td valign="top" >TBD</td>
        </tr>
        <tr>
        <td valign="top" >“vpos”</td>
        <td valign="top" >RANGE</td>
        <td valign="top" >Min=0, Max= SDVO dependent</td>
        <td valign="top" >Connector</td>
        <td valign="top" >TBD</td>
        </tr>
        <tr>
        <td valign="top" >“contrast”</td>
        <td valign="top" >RANGE</td>
        <td valign="top" >Min=0, Max= SDVO dependent</td>
        <td valign="top" >Connector</td>
        <td valign="top" >TBD</td>
        </tr>
        <tr>
        <td valign="top" >“saturation”</td>
        <td valign="top" >RANGE</td>
        <td valign="top" >Min=0, Max= SDVO dependent</td>
        <td valign="top" >Connector</td>
        <td valign="top" >TBD</td>
        </tr>
        <tr>
        <td valign="top" >“hue”</td>
        <td valign="top" >RANGE</td>
        <td valign="top" >Min=0, Max= SDVO dependent</td>
        <td valign="top" >Connector</td>
        <td valign="top" >TBD</td>
        </tr>
        <tr>
        <td valign="top" >“sharpness”</td>
        <td valign="top" >RANGE</td>
        <td valign="top" >Min=0, Max= SDVO dependent</td>
        <td valign="top" >Connector</td>
        <td valign="top" >TBD</td>
        </tr>
        <tr>
        <td valign="top" >“flicker_filter”</td>
        <td valign="top" >RANGE</td>
        <td valign="top" >Min=0, Max= SDVO dependent</td>
        <td valign="top" >Connector</td>
        <td valign="top" >TBD</td>
        </tr>
        <tr>
        <td valign="top" >“flicker_filter_adaptive”</td>
        <td valign="top" >RANGE</td>
        <td valign="top" >Min=0, Max= SDVO dependent</td>
        <td valign="top" >Connector</td>
        <td valign="top" >TBD</td>
        </tr>
        <tr>
        <td valign="top" >“flicker_filter_2d”</td>
        <td valign="top" >RANGE</td>
        <td valign="top" >Min=0, Max= SDVO dependent</td>
        <td valign="top" >Connector</td>
        <td valign="top" >TBD</td>
        </tr>
        <tr>
        <td valign="top" >“tv_chroma_filter”</td>
        <td valign="top" >RANGE</td>
        <td valign="top" >Min=0, Max= SDVO dependent</td>
        <td valign="top" >Connector</td>
        <td valign="top" >TBD</td>
        </tr>
        <tr>
        <td valign="top" >“tv_luma_filter”</td>
        <td valign="top" >RANGE</td>
        <td valign="top" >Min=0, Max= SDVO dependent</td>
        <td valign="top" >Connector</td>
        <td valign="top" >TBD</td>
        </tr>
        <tr>
        <td valign="top" >“dot_crawl”</td>
        <td valign="top" >RANGE</td>
        <td valign="top" >Min=0, Max=1</td>
        <td valign="top" >Connector</td>
        <td valign="top" >TBD</td>
        </tr>
        <tr>
        <td valign="top" >SDVO-TV/LVDS</td>
        <td valign="top" >“brightness”</td>
        <td valign="top" >RANGE</td>
        <td valign="top" >Min=0, Max= SDVO dependent</td>
        <td valign="top" >Connector</td>
        <td valign="top" >TBD</td>
        </tr>
        <tr>
        <td rowspan="3" valign="top" >CDV gma-500</td>
        <td rowspan="3" valign="top" >Generic</td>
        <td valign="top" >"Broadcast RGB"</td>
        <td valign="top" >ENUM</td>
        <td valign="top" >{ “Full”, “Limited 16:235” }</td>
        <td valign="top" >Connector</td>
        <td valign="top" >TBD</td>
        </tr>
        <tr>
        <td valign="top" >"Broadcast RGB"</td>
        <td valign="top" >ENUM</td>
        <td valign="top" >{ “off”, “auto”, “on” }</td>
        <td valign="top" >Connector</td>
        <td valign="top" >TBD</td>
        </tr>
        <tr>
        <td valign="top" >Standard name as in DRM</td>
        <td valign="top" >Standard type as in DRM</td>
        <td valign="top" >Standard value as in DRM</td>
        <td valign="top" >Standard Object as in DRM</td>
        <td valign="top" >TBD</td>
        </tr>
        <tr>
        <td rowspan="20" valign="top" >Poulsbo</td>
        <td rowspan="2" valign="top" >Generic</td>
        <td valign="top" >“backlight”</td>
        <td valign="top" >RANGE</td>
        <td valign="top" >Min=0, Max=100</td>
        <td valign="top" >Connector</td>
        <td valign="top" >TBD</td>
        </tr>
        <tr>
        <td valign="top" >Standard name as in DRM</td>
        <td valign="top" >Standard type as in DRM</td>
        <td valign="top" >Standard value as in DRM</td>
        <td valign="top" >Standard Object as in DRM</td>
        <td valign="top" >TBD</td>
        </tr>
        <tr>
        <td rowspan="17" valign="top" >SDVO-TV</td>
        <td valign="top" >“mode”</td>
        <td valign="top" >ENUM</td>
        <td valign="top" >{ "NTSC_M", "NTSC_J", "NTSC_443", "PAL_B" } etc.</td>
        <td valign="top" >Connector</td>
        <td valign="top" >TBD</td>
        </tr>
        <tr>
        <td valign="top" >"left_margin"</td>
        <td valign="top" >RANGE</td>
        <td valign="top" >Min=0, Max= SDVO dependent</td>
        <td valign="top" >Connector</td>
        <td valign="top" >TBD</td>
        </tr>
        <tr>
        <td valign="top" >"right_margin"</td>
        <td valign="top" >RANGE</td>
        <td valign="top" >Min=0, Max= SDVO dependent</td>
        <td valign="top" >Connector</td>
        <td valign="top" >TBD</td>
        </tr>
        <tr>
        <td valign="top" >"top_margin"</td>
        <td valign="top" >RANGE</td>
        <td valign="top" >Min=0, Max= SDVO dependent</td>
        <td valign="top" >Connector</td>
        <td valign="top" >TBD</td>
        </tr>
        <tr>
        <td valign="top" >"bottom_margin"</td>
        <td valign="top" >RANGE</td>
        <td valign="top" >Min=0, Max= SDVO dependent</td>
        <td valign="top" >Connector</td>
        <td valign="top" >TBD</td>
        </tr>
        <tr>
        <td valign="top" >“hpos”</td>
        <td valign="top" >RANGE</td>
        <td valign="top" >Min=0, Max= SDVO dependent</td>
        <td valign="top" >Connector</td>
        <td valign="top" >TBD</td>
        </tr>
        <tr>
        <td valign="top" >“vpos”</td>
        <td valign="top" >RANGE</td>
        <td valign="top" >Min=0, Max= SDVO dependent</td>
        <td valign="top" >Connector</td>
        <td valign="top" >TBD</td>
        </tr>
        <tr>
        <td valign="top" >“contrast”</td>
        <td valign="top" >RANGE</td>
        <td valign="top" >Min=0, Max= SDVO dependent</td>
        <td valign="top" >Connector</td>
        <td valign="top" >TBD</td>
        </tr>
        <tr>
        <td valign="top" >“saturation”</td>
        <td valign="top" >RANGE</td>
        <td valign="top" >Min=0, Max= SDVO dependent</td>
        <td valign="top" >Connector</td>
        <td valign="top" >TBD</td>
        </tr>
        <tr>
        <td valign="top" >“hue”</td>
        <td valign="top" >RANGE</td>
        <td valign="top" >Min=0, Max= SDVO dependent</td>
        <td valign="top" >Connector</td>
        <td valign="top" >TBD</td>
        </tr>
        <tr>
        <td valign="top" >“sharpness”</td>
        <td valign="top" >RANGE</td>
        <td valign="top" >Min=0, Max= SDVO dependent</td>
        <td valign="top" >Connector</td>
        <td valign="top" >TBD</td>
        </tr>
        <tr>
        <td valign="top" >“flicker_filter”</td>
        <td valign="top" >RANGE</td>
        <td valign="top" >Min=0, Max= SDVO dependent</td>
        <td valign="top" >Connector</td>
        <td valign="top" >TBD</td>
        </tr>
        <tr>
        <td valign="top" >“flicker_filter_adaptive”</td>
        <td valign="top" >RANGE</td>
        <td valign="top" >Min=0, Max= SDVO dependent</td>
        <td valign="top" >Connector</td>
        <td valign="top" >TBD</td>
        </tr>
        <tr>
        <td valign="top" >“flicker_filter_2d”</td>
        <td valign="top" >RANGE</td>
        <td valign="top" >Min=0, Max= SDVO dependent</td>
        <td valign="top" >Connector</td>
        <td valign="top" >TBD</td>
        </tr>
        <tr>
        <td valign="top" >“tv_chroma_filter”</td>
        <td valign="top" >RANGE</td>
        <td valign="top" >Min=0, Max= SDVO dependent</td>
        <td valign="top" >Connector</td>
        <td valign="top" >TBD</td>
        </tr>
        <tr>
        <td valign="top" >“tv_luma_filter”</td>
        <td valign="top" >RANGE</td>
        <td valign="top" >Min=0, Max= SDVO dependent</td>
        <td valign="top" >Connector</td>
        <td valign="top" >TBD</td>
        </tr>
        <tr>
        <td valign="top" >“dot_crawl”</td>
        <td valign="top" >RANGE</td>
        <td valign="top" >Min=0, Max=1</td>
        <td valign="top" >Connector</td>
        <td valign="top" >TBD</td>
        </tr>
        <tr>
        <td valign="top" >SDVO-TV/LVDS</td>
        <td valign="top" >“brightness”</td>
        <td valign="top" >RANGE</td>
        <td valign="top" >Min=0, Max= SDVO dependent</td>
        <td valign="top" >Connector</td>
        <td valign="top" >TBD</td>
        </tr>
        <tr>
        <td rowspan="11" valign="top" >armada</td>
        <td rowspan="2" valign="top" >CRTC</td>
        <td valign="top" >"CSC_YUV"</td>
        <td valign="top" >ENUM</td>
        <td valign="top" >{ "Auto" , "CCIR601", "CCIR709" }</td>
        <td valign="top" >CRTC</td>
        <td valign="top" >TBD</td>
        </tr>
        <tr>
        <td valign="top" >"CSC_RGB"</td>
        <td valign="top" >ENUM</td>
        <td valign="top" >{ "Auto", "Computer system", "Studio" }</td>
        <td valign="top" >CRTC</td>
        <td valign="top" >TBD</td>
        </tr>
        <tr>
        <td rowspan="9" valign="top" >Overlay</td>
        <td valign="top" >"colorkey"</td>
        <td valign="top" >RANGE</td>
        <td valign="top" >Min=0, Max=0xffffff</td>
        <td valign="top" >Plane</td>
        <td valign="top" >TBD</td>
        </tr>
        <tr>
        <td valign="top" >"colorkey_min"</td>
        <td valign="top" >RANGE</td>
        <td valign="top" >Min=0, Max=0xffffff</td>
        <td valign="top" >Plane</td>
        <td valign="top" >TBD</td>
        </tr>
        <tr>
        <td valign="top" >"colorkey_max"</td>
        <td valign="top" >RANGE</td>
        <td valign="top" >Min=0, Max=0xffffff</td>
        <td valign="top" >Plane</td>
        <td valign="top" >TBD</td>
        </tr>
        <tr>
        <td valign="top" >"colorkey_val"</td>
        <td valign="top" >RANGE</td>
        <td valign="top" >Min=0, Max=0xffffff</td>
        <td valign="top" >Plane</td>
        <td valign="top" >TBD</td>
        </tr>
        <tr>
        <td valign="top" >"colorkey_alpha"</td>
        <td valign="top" >RANGE</td>
        <td valign="top" >Min=0, Max=0xffffff</td>
        <td valign="top" >Plane</td>
        <td valign="top" >TBD</td>
        </tr>
        <tr>
        <td valign="top" >"colorkey_mode"</td>
        <td valign="top" >ENUM</td>
        <td valign="top" >{ "disabled", "Y component", "U component"
        , "V component", "RGB", “R component", "G component", "B component" }</td>
        <td valign="top" >Plane</td>
        <td valign="top" >TBD</td>
        </tr>
        <tr>
        <td valign="top" >"brightness"</td>
        <td valign="top" >RANGE</td>
        <td valign="top" >Min=0, Max=256 + 255</td>
        <td valign="top" >Plane</td>
        <td valign="top" >TBD</td>
        </tr>
        <tr>
        <td valign="top" >"contrast"</td>
        <td valign="top" >RANGE</td>
        <td valign="top" >Min=0, Max=0x7fff</td>
        <td valign="top" >Plane</td>
        <td valign="top" >TBD</td>
        </tr>
        <tr>
        <td valign="top" >"saturation"</td>
        <td valign="top" >RANGE</td>
        <td valign="top" >Min=0, Max=0x7fff</td>
        <td valign="top" >Plane</td>
        <td valign="top" >TBD</td>
        </tr>
        <tr>
        <td rowspan="2" valign="top" >exynos</td>
        <td valign="top" >CRTC</td>
        <td valign="top" >“mode”</td>
        <td valign="top" >ENUM</td>
        <td valign="top" >{ "normal", "blank" }</td>
        <td valign="top" >CRTC</td>
        <td valign="top" >TBD</td>
        </tr>
        <tr>
        <td valign="top" >Overlay</td>
        <td valign="top" >“zpos”</td>
        <td valign="top" >RANGE</td>
        <td valign="top" >Min=0, Max=MAX_PLANE-1</td>
        <td valign="top" >Plane</td>
        <td valign="top" >TBD</td>
        </tr>
        <tr>
        <td rowspan="3" valign="top" >i2c/ch7006_drv</td>
        <td valign="top" >Generic</td>
        <td valign="top" >“scale”</td>
        <td valign="top" >RANGE</td>
        <td valign="top" >Min=0, Max=2</td>
        <td valign="top" >Connector</td>
        <td valign="top" >TBD</td>
        </tr>
        <tr>
        <td rowspan="2" valign="top" >TV</td>
        <td valign="top" >Standard names as in DRM</td>
        <td valign="top" >Standard types as in DRM</td>
        <td valign="top" >Standard Values as in DRM</td>
        <td valign="top" >Standard object as in DRM</td>
        <td valign="top" >TBD</td>
        </tr>
        <tr>
        <td valign="top" >“mode”</td>
        <td valign="top" >ENUM</td>
        <td valign="top" >{ "PAL", "PAL-M","PAL-N"}, ”PAL-Nc"
        , "PAL-60", "NTSC-M", "NTSC-J" }</td>
        <td valign="top" >Connector</td>
        <td valign="top" >TBD</td>
        </tr>
        <tr>
        <td rowspan="16" valign="top" >nouveau</td>
        <td rowspan="6" valign="top" >NV10 Overlay</td>
        <td valign="top" >"colorkey"</td>
        <td valign="top" >RANGE</td>
        <td valign="top" >Min=0, Max=0x01ffffff</td>
        <td valign="top" >Plane</td>
        <td valign="top" >TBD</td>
        </tr>
        <tr>
        <td valign="top" >“contrast”</td>
        <td valign="top" >RANGE</td>
        <td valign="top" >Min=0, Max=8192-1</td>
        <td valign="top" >Plane</td>
        <td valign="top" >TBD</td>
        </tr>
        <tr>
        <td valign="top" >“brightness”</td>
        <td valign="top" >RANGE</td>
        <td valign="top" >Min=0, Max=1024</td>
        <td valign="top" >Plane</td>
        <td valign="top" >TBD</td>
        </tr>
        <tr>
        <td valign="top" >“hue”</td>
        <td valign="top" >RANGE</td>
        <td valign="top" >Min=0, Max=359</td>
        <td valign="top" >Plane</td>
        <td valign="top" >TBD</td>
        </tr>
        <tr>
        <td valign="top" >“saturation”</td>
        <td valign="top" >RANGE</td>
        <td valign="top" >Min=0, Max=8192-1</td>
        <td valign="top" >Plane</td>
        <td valign="top" >TBD</td>
        </tr>
        <tr>
        <td valign="top" >“iturbt_709”</td>
        <td valign="top" >RANGE</td>
        <td valign="top" >Min=0, Max=1</td>
        <td valign="top" >Plane</td>
        <td valign="top" >TBD</td>
        </tr>
        <tr>
        <td rowspan="2" valign="top" >Nv04 Overlay</td>
        <td valign="top" >“colorkey”</td>
        <td valign="top" >RANGE</td>
        <td valign="top" >Min=0, Max=0x01ffffff</td>
        <td valign="top" >Plane</td>
        <td valign="top" >TBD</td>
        </tr>
        <tr>
        <td valign="top" >“brightness”</td>
        <td valign="top" >RANGE</td>
        <td valign="top" >Min=0, Max=1024</td>
        <td valign="top" >Plane</td>
        <td valign="top" >TBD</td>
        </tr>
        <tr>
        <td rowspan="7" valign="top" >Display</td>
        <td valign="top" >“dithering mode”</td>
        <td valign="top" >ENUM</td>
        <td valign="top" >{ "auto", "off", "on" }</td>
        <td valign="top" >Connector</td>
        <td valign="top" >TBD</td>
        </tr>
        <tr>
        <td valign="top" >“dithering depth”</td>
        <td valign="top" >ENUM</td>
        <td valign="top" >{ "auto", "off", "on", "static 2x2", "dynamic 2x2", "temporal" }</td>
        <td valign="top" >Connector</td>
        <td valign="top" >TBD</td>
        </tr>
        <tr>
        <td valign="top" >“underscan”</td>
        <td valign="top" >ENUM</td>
        <td valign="top" >{ "auto", "6 bpc", "8 bpc" }</td>
        <td valign="top" >Connector</td>
        <td valign="top" >TBD</td>
        </tr>
        <tr>
        <td valign="top" >“underscan hborder”</td>
        <td valign="top" >RANGE</td>
        <td valign="top" >Min=0, Max=128</td>
        <td valign="top" >Connector</td>
        <td valign="top" >TBD</td>
        </tr>
        <tr>
        <td valign="top" >“underscan vborder”</td>
        <td valign="top" >RANGE</td>
        <td valign="top" >Min=0, Max=128</td>
        <td valign="top" >Connector</td>
        <td valign="top" >TBD</td>
        </tr>
        <tr>
        <td valign="top" >“vibrant hue”</td>
        <td valign="top" >RANGE</td>
        <td valign="top" >Min=0, Max=180</td>
        <td valign="top" >Connector</td>
        <td valign="top" >TBD</td>
        </tr>
        <tr>
        <td valign="top" >“color vibrance”</td>
        <td valign="top" >RANGE</td>
        <td valign="top" >Min=0, Max=200</td>
        <td valign="top" >Connector</td>
        <td valign="top" >TBD</td>
        </tr>
        <tr>
        <td valign="top" >Generic</td>
        <td valign="top" >Standard name as in DRM</td>
        <td valign="top" >Standard type as in DRM</td>
        <td valign="top" >Standard value as in DRM</td>
        <td valign="top" >Standard Object as in DRM</td>
        <td valign="top" >TBD</td>
        </tr>
        <tr>
        <td rowspan="2" valign="top" >omap</td>
        <td rowspan="2" valign="top" >Generic</td>
        <td valign="top" >“rotation”</td>
        <td valign="top" >BITMASK</td>
        <td valign="top" >{ 0, "rotate-0" },
        { 1, "rotate-90" },
        { 2, "rotate-180" },
        { 3, "rotate-270" },
        { 4, "reflect-x" },
        { 5, "reflect-y" }</td>
        <td valign="top" >CRTC, Plane</td>
        <td valign="top" >TBD</td>
        </tr>
        <tr>
        <td valign="top" >“zorder”</td>
        <td valign="top" >RANGE</td>
        <td valign="top" >Min=0, Max=3</td>
        <td valign="top" >CRTC, Plane</td>
        <td valign="top" >TBD</td>
        </tr>
        <tr>
        <td valign="top" >qxl</td>
        <td valign="top" >Generic</td>
        <td valign="top" >“hotplug_mode_update"</td>
        <td valign="top" >RANGE</td>
        <td valign="top" >Min=0, Max=1</td>
        <td valign="top" >Connector</td>
        <td valign="top" >TBD</td>
        </tr>
        <tr>
        <td rowspan="10" valign="top" >radeon</td>
        <td valign="top" >DVI-I</td>
        <td valign="top" >“coherent”</td>
        <td valign="top" >RANGE</td>
        <td valign="top" >Min=0, Max=1</td>
        <td valign="top" >Connector</td>
        <td valign="top" >TBD</td>
        </tr>
        <tr>
        <td valign="top" >DAC enable load detect</td>
        <td valign="top" >“load detection”</td>
        <td valign="top" >RANGE</td>
        <td valign="top" >Min=0, Max=1</td>
        <td valign="top" >Connector</td>
        <td valign="top" >TBD</td>
        </tr>
        <tr>
        <td valign="top" >TV Standard</td>
        <td valign="top" >"tv standard"</td>
        <td valign="top" >ENUM</td>
        <td valign="top" >{ "ntsc", "pal", "pal-m", "pal-60", "ntsc-j"
        , "scart-pal", "pal-cn", "secam" }</td>
        <td valign="top" >Connector</td>
        <td valign="top" >TBD</td>
        </tr>
        <tr>
        <td valign="top" >legacy TMDS PLL detect</td>
        <td valign="top" >"tmds_pll"</td>
        <td valign="top" >ENUM</td>
        <td valign="top" >{ "driver", "bios" }</td>
        <td valign="top" >-</td>
        <td valign="top" >TBD</td>
        </tr>
        <tr>
        <td rowspan="3" valign="top" >Underscan</td>
        <td valign="top" >"underscan"</td>
        <td valign="top" >ENUM</td>
        <td valign="top" >{ "off", "on", "auto" }</td>
        <td valign="top" >Connector</td>
        <td valign="top" >TBD</td>
        </tr>
        <tr>
        <td valign="top" >"underscan hborder"</td>
        <td valign="top" >RANGE</td>
        <td valign="top" >Min=0, Max=128</td>
        <td valign="top" >Connector</td>
        <td valign="top" >TBD</td>
        </tr>
        <tr>
        <td valign="top" >"underscan vborder"</td>
        <td valign="top" >RANGE</td>
        <td valign="top" >Min=0, Max=128</td>
        <td valign="top" >Connector</td>
        <td valign="top" >TBD</td>
        </tr>
        <tr>
        <td valign="top" >Audio</td>
        <td valign="top" >“audio”</td>
        <td valign="top" >ENUM</td>
        <td valign="top" >{ "off", "on", "auto" }</td>
        <td valign="top" >Connector</td>
        <td valign="top" >TBD</td>
        </tr>
        <tr>
        <td valign="top" >FMT Dithering</td>
        <td valign="top" >“dither”</td>
        <td valign="top" >ENUM</td>
        <td valign="top" >{ "off", "on" }</td>
        <td valign="top" >Connector</td>
        <td valign="top" >TBD</td>
        </tr>
        <tr>
        <td valign="top" >Generic</td>
        <td valign="top" >Standard name as in DRM</td>
        <td valign="top" >Standard type as in DRM</td>
        <td valign="top" >Standard value as in DRM</td>
        <td valign="top" >Standard Object as in DRM</td>
        <td valign="top" >TBD</td>
        </tr>
        <tr>
        <td rowspan="3" valign="top" >rcar-du</td>
        <td rowspan="3" valign="top" >Generic</td>
        <td valign="top" >"alpha"</td>
        <td valign="top" >RANGE</td>
        <td valign="top" >Min=0, Max=255</td>
        <td valign="top" >Plane</td>
        <td valign="top" >TBD</td>
        </tr>
        <tr>
        <td valign="top" >"colorkey"</td>
        <td valign="top" >RANGE</td>
        <td valign="top" >Min=0, Max=0x01ffffff</td>
        <td valign="top" >Plane</td>
        <td valign="top" >TBD</td>
        </tr>
        <tr>
        <td valign="top" >"zpos"</td>
        <td valign="top" >RANGE</td>
        <td valign="top" >Min=1, Max=7</td>
        <td valign="top" >Plane</td>
        <td valign="top" >TBD</td>
        </tr>
        </tbody>
        </table>
    </sect2>
  </sect1>

  <!-- Internals: vertical blanking -->

  <sect1 id="drm-vertical-blank">
    <title>Vertical Blanking</title>
    <para>
      Vertical blanking plays a major role in graphics rendering. To achieve
      tear-free display, users must synchronize page flips and/or rendering to
      vertical blanking. The DRM API offers ioctls to perform page flips
      synchronized to vertical blanking and wait for vertical blanking.
    </para>
    <para>
      The DRM core handles most of the vertical blanking management logic, which
      involves filtering out spurious interrupts, keeping race-free blanking
      counters, coping with counter wrap-around and resets and keeping use
      counts. It relies on the driver to generate vertical blanking interrupts
      and optionally provide a hardware vertical blanking counter. Drivers must
      implement the following operations.
    </para>
    <itemizedlist>
      <listitem>
        <synopsis>int (*enable_vblank) (struct drm_device *dev, int crtc);
void (*disable_vblank) (struct drm_device *dev, int crtc);</synopsis>
        <para>
          Enable or disable vertical blanking interrupts for the given CRTC.
        </para>
      </listitem>
      <listitem>
        <synopsis>u32 (*get_vblank_counter) (struct drm_device *dev, int crtc);</synopsis>
        <para>
          Retrieve the value of the vertical blanking counter for the given
          CRTC. If the hardware maintains a vertical blanking counter its value
          should be returned. Otherwise drivers can use the
          <function>drm_vblank_count</function> helper function to handle this
          operation.
        </para>
      </listitem>
    </itemizedlist>
    <para>
      Drivers must initialize the vertical blanking handling core with a call to
      <function>drm_vblank_init</function> in their
      <methodname>load</methodname> operation. The function will set the struct
      <structname>drm_device</structname>
      <structfield>vblank_disable_allowed</structfield> field to 0. This will
      keep vertical blanking interrupts enabled permanently until the first mode
      set operation, where <structfield>vblank_disable_allowed</structfield> is
      set to 1. The reason behind this is not clear. Drivers can set the field
      to 1 after <function>calling drm_vblank_init</function> to make vertical
      blanking interrupts dynamically managed from the beginning.
    </para>
    <para>
      Vertical blanking interrupts can be enabled by the DRM core or by drivers
      themselves (for instance to handle page flipping operations). The DRM core
      maintains a vertical blanking use count to ensure that the interrupts are
      not disabled while a user still needs them. To increment the use count,
      drivers call <function>drm_vblank_get</function>. Upon return vertical
      blanking interrupts are guaranteed to be enabled.
    </para>
    <para>
      To decrement the use count drivers call
      <function>drm_vblank_put</function>. Only when the use count drops to zero
      will the DRM core disable the vertical blanking interrupts after a delay
      by scheduling a timer. The delay is accessible through the vblankoffdelay
      module parameter or the <varname>drm_vblank_offdelay</varname> global
      variable and expressed in milliseconds. Its default value is 5000 ms.
    </para>
    <para>
      When a vertical blanking interrupt occurs drivers only need to call the
      <function>drm_handle_vblank</function> function to account for the
      interrupt.
    </para>
    <para>
      Resources allocated by <function>drm_vblank_init</function> must be freed
      with a call to <function>drm_vblank_cleanup</function> in the driver
      <methodname>unload</methodname> operation handler.
    </para>
    <sect2>
      <title>Vertical Blanking and Interrupt Handling Functions Reference</title>
!Edrivers/gpu/drm/drm_irq.c
    </sect2>
  </sect1>

  <!-- Internals: open/close, file operations and ioctls -->

  <sect1>
    <title>Open/Close, File Operations and IOCTLs</title>
    <sect2>
      <title>Open and Close</title>
      <synopsis>int (*firstopen) (struct drm_device *);
void (*lastclose) (struct drm_device *);
int (*open) (struct drm_device *, struct drm_file *);
void (*preclose) (struct drm_device *, struct drm_file *);
void (*postclose) (struct drm_device *, struct drm_file *);</synopsis>
      <abstract>Open and close handlers. None of those methods are mandatory.
      </abstract>
      <para>
        The <methodname>firstopen</methodname> method is called by the DRM core
        for legacy UMS (User Mode Setting) drivers only when an application
        opens a device that has no other opened file handle. UMS drivers can
        implement it to acquire device resources. KMS drivers can't use the
        method and must acquire resources in the <methodname>load</methodname>
        method instead.
      </para>
      <para>
        Similarly the <methodname>lastclose</methodname> method is called when
        the last application holding a file handle opened on the device closes
        it, for both UMS and KMS drivers. Additionally, the method is also
        called at module unload time or, for hot-pluggable devices, when the
        device is unplugged. The <methodname>firstopen</methodname> and
        <methodname>lastclose</methodname> calls can thus be unbalanced.
      </para>
      <para>
        The <methodname>open</methodname> method is called every time the device
        is opened by an application. Drivers can allocate per-file private data
        in this method and store them in the struct
        <structname>drm_file</structname> <structfield>driver_priv</structfield>
        field. Note that the <methodname>open</methodname> method is called
        before <methodname>firstopen</methodname>.
      </para>
      <para>
        The close operation is split into <methodname>preclose</methodname> and
        <methodname>postclose</methodname> methods. Drivers must stop and
        cleanup all per-file operations in the <methodname>preclose</methodname>
        method. For instance pending vertical blanking and page flip events must
        be cancelled. No per-file operation is allowed on the file handle after
        returning from the <methodname>preclose</methodname> method.
      </para>
      <para>
        Finally the <methodname>postclose</methodname> method is called as the
        last step of the close operation, right before calling the
        <methodname>lastclose</methodname> method if no other open file handle
        exists for the device. Drivers that have allocated per-file private data
        in the <methodname>open</methodname> method should free it here.
      </para>
      <para>
        The <methodname>lastclose</methodname> method should restore CRTC and
        plane properties to default value, so that a subsequent open of the
        device will not inherit state from the previous user. It can also be
        used to execute delayed power switching state changes, e.g. in
        conjunction with the vga-switcheroo infrastructure. Beyond that KMS
        drivers should not do any further cleanup. Only legacy UMS drivers might
        need to clean up device state so that the vga console or an independent
        fbdev driver could take over.
      </para>
    </sect2>
    <sect2>
      <title>File Operations</title>
      <synopsis>const struct file_operations *fops</synopsis>
      <abstract>File operations for the DRM device node.</abstract>
      <para>
        Drivers must define the file operations structure that forms the DRM
        userspace API entry point, even though most of those operations are
        implemented in the DRM core. The <methodname>open</methodname>,
        <methodname>release</methodname> and <methodname>ioctl</methodname>
        operations are handled by
        <programlisting>
        .owner = THIS_MODULE,
        .open = drm_open,
        .release = drm_release,
        .unlocked_ioctl = drm_ioctl,
  #ifdef CONFIG_COMPAT
        .compat_ioctl = drm_compat_ioctl,
  #endif
        </programlisting>
      </para>
      <para>
        Drivers that implement private ioctls that requires 32/64bit
        compatibility support must provide their own
        <methodname>compat_ioctl</methodname> handler that processes private
        ioctls and calls <function>drm_compat_ioctl</function> for core ioctls.
      </para>
      <para>
        The <methodname>read</methodname> and <methodname>poll</methodname>
        operations provide support for reading DRM events and polling them. They
        are implemented by
        <programlisting>
        .poll = drm_poll,
        .read = drm_read,
        .llseek = no_llseek,
        </programlisting>
      </para>
      <para>
        The memory mapping implementation varies depending on how the driver
        manages memory. Pre-GEM drivers will use <function>drm_mmap</function>,
        while GEM-aware drivers will use <function>drm_gem_mmap</function>. See
        <xref linkend="drm-gem"/>.
        <programlisting>
        .mmap = drm_gem_mmap,
        </programlisting>
      </para>
      <para>
        No other file operation is supported by the DRM API.
      </para>
    </sect2>
    <sect2>
      <title>IOCTLs</title>
      <synopsis>struct drm_ioctl_desc *ioctls;
int num_ioctls;</synopsis>
      <abstract>Driver-specific ioctls descriptors table.</abstract>
      <para>
        Driver-specific ioctls numbers start at DRM_COMMAND_BASE. The ioctls
        descriptors table is indexed by the ioctl number offset from the base
        value. Drivers can use the DRM_IOCTL_DEF_DRV() macro to initialize the
        table entries.
      </para>
      <para>
        <programlisting>DRM_IOCTL_DEF_DRV(ioctl, func, flags)</programlisting>
        <para>
          <parameter>ioctl</parameter> is the ioctl name. Drivers must define
          the DRM_##ioctl and DRM_IOCTL_##ioctl macros to the ioctl number
          offset from DRM_COMMAND_BASE and the ioctl number respectively. The
          first macro is private to the device while the second must be exposed
          to userspace in a public header.
        </para>
        <para>
          <parameter>func</parameter> is a pointer to the ioctl handler function
          compatible with the <type>drm_ioctl_t</type> type.
          <programlisting>typedef int drm_ioctl_t(struct drm_device *dev, void *data,
                struct drm_file *file_priv);</programlisting>
        </para>
        <para>
          <parameter>flags</parameter> is a bitmask combination of the following
          values. It restricts how the ioctl is allowed to be called.
          <itemizedlist>
            <listitem><para>
              DRM_AUTH - Only authenticated callers allowed
            </para></listitem>
            <listitem><para>
              DRM_MASTER - The ioctl can only be called on the master file
              handle
            </para></listitem>
            <listitem><para>
              DRM_ROOT_ONLY - Only callers with the SYSADMIN capability allowed
            </para></listitem>
            <listitem><para>
              DRM_CONTROL_ALLOW - The ioctl can only be called on a control
              device
            </para></listitem>
            <listitem><para>
              DRM_UNLOCKED - The ioctl handler will be called without locking
              the DRM global mutex
            </para></listitem>
          </itemizedlist>
        </para>
      </para>
    </sect2>
  </sect1>
  <sect1>
    <title>Legacy Support Code</title>
    <para>
      The section very briefly covers some of the old legacy support code which
      is only used by old DRM drivers which have done a so-called shadow-attach
      to the underlying device instead of registering as a real driver. This
      also includes some of the old generic buffer management and command
      submission code. Do not use any of this in new and modern drivers.
    </para>

    <sect2>
      <title>Legacy Suspend/Resume</title>
      <para>
        The DRM core provides some suspend/resume code, but drivers wanting full
        suspend/resume support should provide save() and restore() functions.
        These are called at suspend, hibernate, or resume time, and should perform
        any state save or restore required by your device across suspend or
        hibernate states.
      </para>
      <synopsis>int (*suspend) (struct drm_device *, pm_message_t state);
  int (*resume) (struct drm_device *);</synopsis>
      <para>
        Those are legacy suspend and resume methods which
        <emphasis>only</emphasis> work with the legacy shadow-attach driver
        registration functions. New driver should use the power management
        interface provided by their bus type (usually through
        the struct <structname>device_driver</structname> dev_pm_ops) and set
        these methods to NULL.
      </para>
    </sect2>

    <sect2>
      <title>Legacy DMA Services</title>
      <para>
        This should cover how DMA mapping etc. is supported by the core.
        These functions are deprecated and should not be used.
      </para>
    </sect2>
  </sect1>
  </chapter>

<!-- TODO

- Add a glossary
- Document the struct_mutex catch-all lock
- Document connector properties

- Why is the load method optional?
- What are drivers supposed to set the initial display state to, and how?
  Connector's DPMS states are not initialized and are thus equal to
  DRM_MODE_DPMS_ON. The fbcon compatibility layer calls
  drm_helper_disable_unused_functions(), which disables unused encoders and
  CRTCs, but doesn't touch the connectors' DPMS state, and
  drm_helper_connector_dpms() in reaction to fbdev blanking events. Do drivers
  that don't implement (or just don't use) fbcon compatibility need to call
  those functions themselves?
- KMS drivers must call drm_vblank_pre_modeset() and drm_vblank_post_modeset()
  around mode setting. Should this be done in the DRM core?
- vblank_disable_allowed is set to 1 in the first drm_vblank_post_modeset()
  call and never set back to 0. It seems to be safe to permanently set it to 1
  in drm_vblank_init() for KMS driver, and it might be safe for UMS drivers as
  well. This should be investigated.
- crtc and connector .save and .restore operations are only used internally in
  drivers, should they be removed from the core?
- encoder mid-layer .save and .restore operations are only used internally in
  drivers, should they be removed from the core?
- encoder mid-layer .detect operation is only used internally in drivers,
  should it be removed from the core?
-->

  <!-- External interfaces -->

  <chapter id="drmExternals">
    <title>Userland interfaces</title>
    <para>
      The DRM core exports several interfaces to applications,
      generally intended to be used through corresponding libdrm
      wrapper functions.  In addition, drivers export device-specific
      interfaces for use by userspace drivers &amp; device-aware
      applications through ioctls and sysfs files.
    </para>
    <para>
      External interfaces include: memory mapping, context management,
      DMA operations, AGP management, vblank control, fence
      management, memory management, and output management.
    </para>
    <para>
      Cover generic ioctls and sysfs layout here.  We only need high-level
      info, since man pages should cover the rest.
    </para>

  <!-- External: render nodes -->

    <sect1>
      <title>Render nodes</title>
      <para>
        DRM core provides multiple character-devices for user-space to use.
        Depending on which device is opened, user-space can perform a different
        set of operations (mainly ioctls). The primary node is always created
        and called card&lt;num&gt;. Additionally, a currently
        unused control node, called controlD&lt;num&gt; is also
        created. The primary node provides all legacy operations and
        historically was the only interface used by userspace. With KMS, the
        control node was introduced. However, the planned KMS control interface
        has never been written and so the control node stays unused to date.
      </para>
      <para>
        With the increased use of offscreen renderers and GPGPU applications,
        clients no longer require running compositors or graphics servers to
        make use of a GPU. But the DRM API required unprivileged clients to
        authenticate to a DRM-Master prior to getting GPU access. To avoid this
        step and to grant clients GPU access without authenticating, render
        nodes were introduced. Render nodes solely serve render clients, that
        is, no modesetting or privileged ioctls can be issued on render nodes.
        Only non-global rendering commands are allowed. If a driver supports
        render nodes, it must advertise it via the DRIVER_RENDER
        DRM driver capability. If not supported, the primary node must be used
        for render clients together with the legacy drmAuth authentication
        procedure.
      </para>
      <para>
        If a driver advertises render node support, DRM core will create a
        separate render node called renderD&lt;num&gt;. There will
        be one render node per device. No ioctls except  PRIME-related ioctls
        will be allowed on this node. Especially GEM_OPEN will be
        explicitly prohibited. Render nodes are designed to avoid the
        buffer-leaks, which occur if clients guess the flink names or mmap
        offsets on the legacy interface. Additionally to this basic interface,
        drivers must mark their driver-dependent render-only ioctls as
        DRM_RENDER_ALLOW so render clients can use them. Driver
        authors must be careful not to allow any privileged ioctls on render
        nodes.
      </para>
      <para>
        With render nodes, user-space can now control access to the render node
        via basic file-system access-modes. A running graphics server which
        authenticates clients on the privileged primary/legacy node is no longer
        required. Instead, a client can open the render node and is immediately
        granted GPU access. Communication between clients (or servers) is done
        via PRIME. FLINK from render node to legacy node is not supported. New
        clients must not use the insecure FLINK interface.
      </para>
      <para>
        Besides dropping all modeset/global ioctls, render nodes also drop the
        DRM-Master concept. There is no reason to associate render clients with
        a DRM-Master as they are independent of any graphics server. Besides,
        they must work without any running master, anyway.
        Drivers must be able to run without a master object if they support
        render nodes. If, on the other hand, a driver requires shared state
        between clients which is visible to user-space and accessible beyond
        open-file boundaries, they cannot support render nodes.
      </para>
    </sect1>

  <!-- External: vblank handling -->

    <sect1>
      <title>VBlank event handling</title>
      <para>
        The DRM core exposes two vertical blank related ioctls:
        <variablelist>
          <varlistentry>
            <term>DRM_IOCTL_WAIT_VBLANK</term>
            <listitem>
              <para>
                This takes a struct drm_wait_vblank structure as its argument,
                and it is used to block or request a signal when a specified
                vblank event occurs.
              </para>
            </listitem>
          </varlistentry>
          <varlistentry>
            <term>DRM_IOCTL_MODESET_CTL</term>
            <listitem>
              <para>
                This was only used for user-mode-settind drivers around
                modesetting changes to allow the kernel to update the vblank
                interrupt after mode setting, since on many devices the vertical
                blank counter is reset to 0 at some point during modeset. Modern
                drivers should not call this any more since with kernel mode
                setting it is a no-op.
              </para>
            </listitem>
          </varlistentry>
        </variablelist>
      </para>
    </sect1>

  </chapter>
</part>
<part id="drmDrivers">
  <title>DRM Drivers</title>

  <partintro>
    <para>
      This second part of the DRM Developer's Guide documents driver code,
      implementation details and also all the driver-specific userspace
      interfaces. Especially since all hardware-acceleration interfaces to
      userspace are driver specific for efficiency and other reasons these
      interfaces can be rather substantial. Hence every driver has its own
      chapter.
    </para>
  </partintro>

  <chapter id="drmI915">
    <title>drm/i915 Intel GFX Driver</title>
    <para>
      The drm/i915 driver supports all (with the exception of some very early
      models) integrated GFX chipsets with both Intel display and rendering
      blocks. This excludes a set of SoC platforms with an SGX rendering unit,
      those have basic support through the gma500 drm driver.
    </para>
    <sect1>
      <title>Display Hardware Handling</title>
      <para>
        This section covers everything related to the display hardware including
        the mode setting infrastructure, plane, sprite and cursor handling and
        display, output probing and related topics.
      </para>
      <sect2>
        <title>Mode Setting Infrastructure</title>
        <para>
          The i915 driver is thus far the only DRM driver which doesn't use the
          common DRM helper code to implement mode setting sequences. Thus it
          has its own tailor-made infrastructure for executing a display
          configuration change.
        </para>
      </sect2>
      <sect2>
        <title>Plane Configuration</title>
        <para>
          This section covers plane configuration and composition with the
          primary plane, sprites, cursors and overlays. This includes the
          infrastructure to do atomic vsync'ed updates of all this state and
          also tightly coupled topics like watermark setup and computation,
          framebuffer compression and panel self refresh.
        </para>
      </sect2>
      <sect2>
        <title>Output Probing</title>
        <para>
          This section covers output probing and related infrastructure like the
          hotplug interrupt storm detection and mitigation code. Note that the
          i915 driver still uses most of the common DRM helper code for output
          probing, so those sections fully apply.
        </para>
      </sect2>
      <sect2>
        <title>DPIO</title>
!Pdrivers/gpu/drm/i915/i915_reg.h DPIO
        <table id="dpiox2">
          <title>Dual channel PHY (VLV/CHV)</title>
          <tgroup cols="8">
            <colspec colname="c0" />
            <colspec colname="c1" />
            <colspec colname="c2" />
            <colspec colname="c3" />
            <colspec colname="c4" />
            <colspec colname="c5" />
            <colspec colname="c6" />
            <colspec colname="c7" />
            <spanspec spanname="ch0" namest="c0" nameend="c3" />
            <spanspec spanname="ch1" namest="c4" nameend="c7" />
            <spanspec spanname="ch0pcs01" namest="c0" nameend="c1" />
            <spanspec spanname="ch0pcs23" namest="c2" nameend="c3" />
            <spanspec spanname="ch1pcs01" namest="c4" nameend="c5" />
            <spanspec spanname="ch1pcs23" namest="c6" nameend="c7" />
            <thead>
              <row>
                <entry spanname="ch0">CH0</entry>
                <entry spanname="ch1">CH1</entry>
              </row>
            </thead>
            <tbody valign="top" align="center">
              <row>
                <entry spanname="ch0">CMN/PLL/REF</entry>
                <entry spanname="ch1">CMN/PLL/REF</entry>
              </row>
              <row>
                <entry spanname="ch0pcs01">PCS01</entry>
                <entry spanname="ch0pcs23">PCS23</entry>
                <entry spanname="ch1pcs01">PCS01</entry>
                <entry spanname="ch1pcs23">PCS23</entry>
              </row>
              <row>
                <entry>TX0</entry>
                <entry>TX1</entry>
                <entry>TX2</entry>
                <entry>TX3</entry>
                <entry>TX0</entry>
                <entry>TX1</entry>
                <entry>TX2</entry>
                <entry>TX3</entry>
              </row>
              <row>
                <entry spanname="ch0">DDI0</entry>
                <entry spanname="ch1">DDI1</entry>
              </row>
            </tbody>
          </tgroup>
        </table>
        <table id="dpiox1">
          <title>Single channel PHY (CHV)</title>
          <tgroup cols="4">
            <colspec colname="c0" />
            <colspec colname="c1" />
            <colspec colname="c2" />
            <colspec colname="c3" />
            <spanspec spanname="ch0" namest="c0" nameend="c3" />
            <spanspec spanname="ch0pcs01" namest="c0" nameend="c1" />
            <spanspec spanname="ch0pcs23" namest="c2" nameend="c3" />
            <thead>
              <row>
                <entry spanname="ch0">CH0</entry>
              </row>
            </thead>
            <tbody valign="top" align="center">
              <row>
                <entry spanname="ch0">CMN/PLL/REF</entry>
              </row>
              <row>
                <entry spanname="ch0pcs01">PCS01</entry>
                <entry spanname="ch0pcs23">PCS23</entry>
              </row>
              <row>
                <entry>TX0</entry>
                <entry>TX1</entry>
                <entry>TX2</entry>
                <entry>TX3</entry>
              </row>
              <row>
                <entry spanname="ch0">DDI2</entry>
              </row>
            </tbody>
          </tgroup>
        </table>
      </sect2>
    </sect1>

    <sect1>
      <title>Memory Management and Command Submission</title>
      <para>
        This sections covers all things related to the GEM implementation in the
        i915 driver.
      </para>
      <sect2>
        <title>Batchbuffer Parsing</title>
!Pdrivers/gpu/drm/i915/i915_cmd_parser.c batch buffer command parser
!Idrivers/gpu/drm/i915/i915_cmd_parser.c
      </sect2>
    </sect1>
  </chapter>
</part>
</book>