arch/arm/boot/dts/kirkwood-dockstar.dts

   1 /dts-v1/;
   2
   3 #include "kirkwood.dtsi"
   4 #include "kirkwood-6281.dtsi"
   5
   6 / {
   7         model = "Seagate FreeAgent Dockstar";
   8         compatible = "seagate,dockstar", "marvell,kirkwood-88f6281", "marvell,kirkwood";
   9
  10         memory {
  11                 device_type = "memory";
  12                 reg = <0x00000000 0x8000000>;
  13         };
  14
  15         chosen {
  16                 bootargs = "console=ttyS0,115200n8 earlyprintk root=/dev/sda1 rootdelay=10";
  17                 stdout-path = &uart0;
  18         };
  19
  20         ocp@f1000000 {
  21                 pinctrl: pin-controller@10000 {
  22                         pmx_usb_power_enable: pmx-usb-power-enable {
  23                                 marvell,pins = "mpp29";
  24                                 marvell,function = "gpio";
  25                         };
  26                         pmx_led_green: pmx-led-green {
  27                                 marvell,pins = "mpp46";
  28                                 marvell,function = "gpio";
  29                         };
  30                         pmx_led_orange: pmx-led-orange {
  31                                 marvell,pins = "mpp47";
  32                                 marvell,function = "gpio";
  33                         };
  34                 };
  35                 serial@12000 {
  36                         status = "ok";
  37                 };
  38         };
  39         gpio-leds {
  40                 compatible = "gpio-leds";
  41                 pinctrl-0 = <&pmx_led_green &pmx_led_orange>;
  42                 pinctrl-names = "default";
  43
  44                 health {
  45                         label = "status:green:health";
  46                         gpios = <&gpio1 14 GPIO_ACTIVE_LOW>;
  47                         default-state = "keep";
  48                 };
  49                 fault {
  50                         label = "status:orange:fault";
  51                         gpios = <&gpio1 15 GPIO_ACTIVE_LOW>;
  52                 };
  53         };
  54         regulators {
  55                 compatible = "simple-bus";
  56                 #address-cells = <1>;
  57                 #size-cells = <0>;
  58                 pinctrl-0 = <&pmx_usb_power_enable>;
  59                 pinctrl-names = "default";
  60
  61                 usb_power: regulator@1 {
  62                         compatible = "regulator-fixed";
  63                         reg = <1>;
  64                         regulator-name = "USB Power";
  65                         regulator-min-microvolt = <5000000>;
  66                         regulator-max-microvolt = <5000000>;
  67                         enable-active-high;
  68                         regulator-always-on;
  69                         regulator-boot-on;
  70                         gpio = <&gpio0 29 0>;
  71                 };
  72         };
  73 };
  74
  75 &nand {
  76         status = "okay";
  77
  78         partition@0 {
  79                 label = "u-boot";
  80                 reg = <0x0000000 0x100000>;
  81                 read-only;
  82         };
  83
  84         partition@100000 {
  85                 label = "uImage";
  86                 reg = <0x0100000 0x400000>;
  87         };
  88
  89         partition@500000 {
  90                 label = "data";
  91                 reg = <0x0500000 0xfb00000>;
  92         };
  93 };
  94
  95 &mdio {
  96         status = "okay";
  97
  98         ethphy0: ethernet-phy@0 {
  99                 compatible = "marvell,88e1116";
 100                 reg = <0>;
 101         };
 102 };
 103
 104 &eth0 {
 105         status = "okay";
 106         ethernet0-port@0 {
 107                 phy-handle = <&ethphy0>;
 108         };
 109 };