mm: hugetlb: fix hugepage memory leak caused by wrong reserve count
[linux/fpc-iii.git] / arch / arm64 / boot / dts / qcom / pm8916.dtsi
blobb222ece7e3d25af69afd56f3d1912b1520c27985
1 #include <dt-bindings/iio/qcom,spmi-vadc.h>
2 #include <dt-bindings/interrupt-controller/irq.h>
3 #include <dt-bindings/spmi/spmi.h>
5 &spmi_bus {
7         usid0: pm8916@0 {
8                 compatible = "qcom,spmi-pmic";
9                 reg = <0x0 SPMI_USID>;
10                 #address-cells = <1>;
11                 #size-cells = <0>;
13                 rtc@6000 {
14                         compatible = "qcom,pm8941-rtc";
15                         reg = <0x6000 0x6100>;
16                         reg-names = "rtc", "alarm";
17                         interrupts = <0x0 0x61 0x1 IRQ_TYPE_EDGE_RISING>;
18                 };
20                 pwrkey@800 {
21                         compatible = "qcom,pm8941-pwrkey";
22                         reg = <0x800>;
23                         interrupts = <0x0 0x8 0 IRQ_TYPE_EDGE_BOTH>;
24                         debounce = <15625>;
25                         bias-pull-up;
26                 };
28                 pm8916_gpios: gpios@c000 {
29                         compatible = "qcom,pm8916-gpio";
30                         reg = <0xc000 0x400>;
31                         gpio-controller;
32                         #gpio-cells = <2>;
33                         interrupts = <0 0xc0 0 IRQ_TYPE_NONE>,
34                                      <0 0xc1 0 IRQ_TYPE_NONE>,
35                                      <0 0xc2 0 IRQ_TYPE_NONE>,
36                                      <0 0xc3 0 IRQ_TYPE_NONE>;
37                 };
39                 pm8916_mpps: mpps@a000 {
40                         compatible = "qcom,pm8916-mpp";
41                         reg = <0xa000 0x400>;
42                         gpio-controller;
43                         #gpio-cells = <2>;
44                         interrupts = <0 0xa0 0 IRQ_TYPE_NONE>,
45                                      <0 0xa1 0 IRQ_TYPE_NONE>,
46                                      <0 0xa2 0 IRQ_TYPE_NONE>,
47                                      <0 0xa3 0 IRQ_TYPE_NONE>;
48                 };
50                 pm8916_temp: temp-alarm@2400 {
51                         compatible = "qcom,spmi-temp-alarm";
52                         reg = <0x2400 0x100>;
53                         interrupts = <0 0x24 0 IRQ_TYPE_EDGE_RISING>;
54                         io-channels = <&pm8916_vadc VADC_DIE_TEMP>;
55                         io-channel-names = "thermal";
56                         #thermal-sensor-cells = <0>;
57                 };
59                 pm8916_vadc: vadc@3100 {
60                         compatible = "qcom,spmi-vadc";
61                         reg = <0x3100 0x100>;
62                         interrupts = <0x0 0x31 0x0 IRQ_TYPE_EDGE_RISING>;
63                         #address-cells = <1>;
64                         #size-cells = <0>;
65                         #io-channel-cells = <1>;
67                         usb_in {
68                                 reg = <VADC_USBIN>;
69                                 qcom,pre-scaling = <1 10>;
70                         };
71                         vph_pwr {
72                                 reg = <VADC_VSYS>;
73                                 qcom,pre-scaling = <1 3>;
74                         };
75                         die_temp {
76                                 reg = <VADC_DIE_TEMP>;
77                         };
78                         ref_625mv {
79                                 reg = <VADC_REF_625MV>;
80                         };
81                         ref_1250v {
82                                 reg = <VADC_REF_1250MV>;
83                         };
84                         ref_gnd {
85                                 reg = <VADC_GND_REF>;
86                         };
87                         ref_vdd {
88                                 reg = <VADC_VDD_VADC>;
89                         };
90                 };
91         };
93         usid1: pm8916@1 {
94                 compatible = "qcom,spmi-pmic";
95                 reg = <0x1 SPMI_USID>;
96                 #address-cells = <1>;
97                 #size-cells = <0>;
98         };