dt-bindings: mtd: ingenic: Use standard ecc-engine property

[linux/fpc-iii.git] / drivers / gpu / drm / bridge / sil-sii8620.h

/*
 * Registers of Silicon Image SiI8620 Mobile HD Transmitter
 *
 * Copyright (C) 2015, Samsung Electronics Co., Ltd.
 * Andrzej Hajda <a.hajda@samsung.com>
 *
 * Based on MHL driver for Android devices.
 * Copyright (C) 2013-2014 Silicon Image, Inc.
 *
 * This program is free software; you can redistribute it and/or modify
 * it under the terms of the GNU General Public License version 2 as
 * published by the Free Software Foundation.
 */

#ifndef __SIL_SII8620_H__
#define __SIL_SII8620_H__

/* Vendor ID Low byte, default value: 0x01 */
#define REG_VND_IDL                             0x0000

/* Vendor ID High byte, default value: 0x00 */
#define REG_VND_IDH                             0x0001

/* Device ID Low byte, default value: 0x60 */
#define REG_DEV_IDL                             0x0002

/* Device ID High byte, default value: 0x86 */
#define REG_DEV_IDH                             0x0003

/* Device Revision, default value: 0x10 */
#define REG_DEV_REV                             0x0004

/* OTP DBYTE510, default value: 0x00 */
#define REG_OTP_DBYTE510                        0x0006

/* System Control #1, default value: 0x00 */
#define REG_SYS_CTRL1                           0x0008
#define BIT_SYS_CTRL1_OTPVMUTEOVR_SET           BIT(7)
#define BIT_SYS_CTRL1_VSYNCPIN                  BIT(6)
#define BIT_SYS_CTRL1_OTPADROPOVR_SET           BIT(5)
#define BIT_SYS_CTRL1_BLOCK_DDC_BY_HPD          BIT(4)
#define BIT_SYS_CTRL1_OTP2XVOVR_EN              BIT(3)
#define BIT_SYS_CTRL1_OTP2XAOVR_EN              BIT(2)
#define BIT_SYS_CTRL1_TX_CTRL_HDMI              BIT(1)
#define BIT_SYS_CTRL1_OTPAMUTEOVR_SET           BIT(0)

/* System Control DPD, default value: 0x90 */
#define REG_DPD                                 0x000b
#define BIT_DPD_PWRON_PLL                       BIT(7)
#define BIT_DPD_PDNTX12                         BIT(6)
#define BIT_DPD_PDNRX12                         BIT(5)
#define BIT_DPD_OSC_EN                          BIT(4)
#define BIT_DPD_PWRON_HSIC                      BIT(3)
#define BIT_DPD_PDIDCK_N                        BIT(2)
#define BIT_DPD_PD_MHL_CLK_N                    BIT(1)

/* Dual link Control, default value: 0x00 */
#define REG_DCTL                                0x000d
#define BIT_DCTL_TDM_LCLK_PHASE                 BIT(7)
#define BIT_DCTL_HSIC_CLK_PHASE                 BIT(6)
#define BIT_DCTL_CTS_TCK_PHASE                  BIT(5)
#define BIT_DCTL_EXT_DDC_SEL                    BIT(4)
#define BIT_DCTL_TRANSCODE                      BIT(3)
#define BIT_DCTL_HSIC_RX_STROBE_PHASE           BIT(2)
#define BIT_DCTL_HSIC_TX_BIST_START_SEL         BIT(1)
#define BIT_DCTL_TCLKNX_PHASE                   BIT(0)

/* PWD Software Reset, default value: 0x20 */
#define REG_PWD_SRST                            0x000e
#define BIT_PWD_SRST_COC_DOC_RST                BIT(7)
#define BIT_PWD_SRST_CBUS_RST_SW                BIT(6)
#define BIT_PWD_SRST_CBUS_RST_SW_EN             BIT(5)
#define BIT_PWD_SRST_MHLFIFO_RST                BIT(4)
#define BIT_PWD_SRST_CBUS_RST                   BIT(3)
#define BIT_PWD_SRST_SW_RST_AUTO                BIT(2)
#define BIT_PWD_SRST_HDCP2X_SW_RST              BIT(1)
#define BIT_PWD_SRST_SW_RST                     BIT(0)

/* AKSV_1, default value: 0x00 */
#define REG_AKSV_1                              0x001d

/* Video H Resolution #1, default value: 0x00 */
#define REG_H_RESL                              0x003a

/* Video Mode, default value: 0x00 */
#define REG_VID_MODE                            0x004a
#define BIT_VID_MODE_M1080P                     BIT(6)

/* Video Input Mode, default value: 0xc0 */
#define REG_VID_OVRRD                           0x0051
#define BIT_VID_OVRRD_PP_AUTO_DISABLE           BIT(7)
#define BIT_VID_OVRRD_M1080P_OVRRD              BIT(6)
#define BIT_VID_OVRRD_MINIVSYNC_ON              BIT(5)
#define BIT_VID_OVRRD_3DCONV_EN_FRAME_PACK      BIT(4)
#define BIT_VID_OVRRD_ENABLE_AUTO_PATH_EN       BIT(3)
#define BIT_VID_OVRRD_ENRGB2YCBCR_OVRRD         BIT(2)
#define BIT_VID_OVRRD_ENDOWNSAMPLE_OVRRD        BIT(0)

/* I2C Address reassignment, default value: 0x00 */
#define REG_PAGE_MHLSPEC_ADDR                   0x0057
#define REG_PAGE7_ADDR                          0x0058
#define REG_PAGE8_ADDR                          0x005c

/* Fast Interrupt Status, default value: 0x00 */
#define REG_FAST_INTR_STAT                      0x005f
#define LEN_FAST_INTR_STAT                      7
#define BIT_FAST_INTR_STAT_TIMR                 8
#define BIT_FAST_INTR_STAT_INT2                 9
#define BIT_FAST_INTR_STAT_DDC                  10
#define BIT_FAST_INTR_STAT_SCDT                 11
#define BIT_FAST_INTR_STAT_INFR                 13
#define BIT_FAST_INTR_STAT_EDID                 14
#define BIT_FAST_INTR_STAT_HDCP                 15
#define BIT_FAST_INTR_STAT_MSC                  16
#define BIT_FAST_INTR_STAT_MERR                 17
#define BIT_FAST_INTR_STAT_G2WB                 18
#define BIT_FAST_INTR_STAT_G2WB_ERR             19
#define BIT_FAST_INTR_STAT_DISC                 28
#define BIT_FAST_INTR_STAT_BLOCK                30
#define BIT_FAST_INTR_STAT_LTRN                 31
#define BIT_FAST_INTR_STAT_HDCP2                32
#define BIT_FAST_INTR_STAT_TDM                  42
#define BIT_FAST_INTR_STAT_COC                  51

/* GPIO Control, default value: 0x15 */
#define REG_GPIO_CTRL1                          0x006e
#define BIT_CTRL1_GPIO_I_8                      BIT(5)
#define BIT_CTRL1_GPIO_OEN_8                    BIT(4)
#define BIT_CTRL1_GPIO_I_7                      BIT(3)
#define BIT_CTRL1_GPIO_OEN_7                    BIT(2)
#define BIT_CTRL1_GPIO_I_6                      BIT(1)
#define BIT_CTRL1_GPIO_OEN_6                    BIT(0)

/* Interrupt Control, default value: 0x06 */
#define REG_INT_CTRL                            0x006f
#define BIT_INT_CTRL_SOFTWARE_WP                BIT(7)
#define BIT_INT_CTRL_INTR_OD                    BIT(2)
#define BIT_INT_CTRL_INTR_POLARITY              BIT(1)

/* Interrupt State, default value: 0x00 */
#define REG_INTR_STATE                          0x0070
#define BIT_INTR_STATE_INTR_STATE               BIT(0)

/* Interrupt Source #1, default value: 0x00 */
#define REG_INTR1                               0x0071

/* Interrupt Source #2, default value: 0x00 */
#define REG_INTR2                               0x0072

/* Interrupt Source #3, default value: 0x01 */
#define REG_INTR3                               0x0073
#define BIT_DDC_CMD_DONE                        BIT(3)

/* Interrupt Source #5, default value: 0x00 */
#define REG_INTR5                               0x0074

/* Interrupt #1 Mask, default value: 0x00 */
#define REG_INTR1_MASK                          0x0075

/* Interrupt #2 Mask, default value: 0x00 */
#define REG_INTR2_MASK                          0x0076

/* Interrupt #3 Mask, default value: 0x00 */
#define REG_INTR3_MASK                          0x0077

/* Interrupt #5 Mask, default value: 0x00 */
#define REG_INTR5_MASK                          0x0078
#define BIT_INTR_SCDT_CHANGE                    BIT(0)

/* Hot Plug Connection Control, default value: 0x45 */
#define REG_HPD_CTRL                            0x0079
#define BIT_HPD_CTRL_HPD_DS_SIGNAL              BIT(7)
#define BIT_HPD_CTRL_HPD_OUT_OD_EN              BIT(6)
#define BIT_HPD_CTRL_HPD_HIGH                   BIT(5)
#define BIT_HPD_CTRL_HPD_OUT_OVR_EN             BIT(4)
#define BIT_HPD_CTRL_GPIO_I_1                   BIT(3)
#define BIT_HPD_CTRL_GPIO_OEN_1                 BIT(2)
#define BIT_HPD_CTRL_GPIO_I_0                   BIT(1)
#define BIT_HPD_CTRL_GPIO_OEN_0                 BIT(0)

/* GPIO Control, default value: 0x55 */
#define REG_GPIO_CTRL                           0x007a
#define BIT_CTRL_GPIO_I_5                       BIT(7)
#define BIT_CTRL_GPIO_OEN_5                     BIT(6)
#define BIT_CTRL_GPIO_I_4                       BIT(5)
#define BIT_CTRL_GPIO_OEN_4                     BIT(4)
#define BIT_CTRL_GPIO_I_3                       BIT(3)
#define BIT_CTRL_GPIO_OEN_3                     BIT(2)
#define BIT_CTRL_GPIO_I_2                       BIT(1)
#define BIT_CTRL_GPIO_OEN_2                     BIT(0)

/* Interrupt Source 7, default value: 0x00 */
#define REG_INTR7                               0x007b

/* Interrupt Source 8, default value: 0x00 */
#define REG_INTR8                               0x007c

/* Interrupt #7 Mask, default value: 0x00 */
#define REG_INTR7_MASK                          0x007d

/* Interrupt #8 Mask, default value: 0x00 */
#define REG_INTR8_MASK                          0x007e
#define BIT_CEA_NEW_VSI                         BIT(2)
#define BIT_CEA_NEW_AVI                         BIT(1)

/* IEEE, default value: 0x10 */
#define REG_TMDS_CCTRL                          0x0080
#define BIT_TMDS_CCTRL_TMDS_OE                  BIT(4)

/* TMDS Control #4, default value: 0x02 */
#define REG_TMDS_CTRL4                          0x0085
#define BIT_TMDS_CTRL4_SCDT_CKDT_SEL            BIT(1)
#define BIT_TMDS_CTRL4_TX_EN_BY_SCDT            BIT(0)

/* BIST CNTL, default value: 0x00 */
#define REG_BIST_CTRL                           0x00bb
#define BIT_RXBIST_VGB_EN                       BIT(7)
#define BIT_TXBIST_VGB_EN                       BIT(6)
#define BIT_BIST_START_SEL                      BIT(5)
#define BIT_BIST_START_BIT                      BIT(4)
#define BIT_BIST_ALWAYS_ON                      BIT(3)
#define BIT_BIST_TRANS                          BIT(2)
#define BIT_BIST_RESET                          BIT(1)
#define BIT_BIST_EN                             BIT(0)

/* BIST DURATION0, default value: 0x00 */
#define REG_BIST_TEST_SEL                       0x00bd
#define MSK_BIST_TEST_SEL_BIST_PATT_SEL         0x0f

/* BIST VIDEO_MODE, default value: 0x00 */
#define REG_BIST_VIDEO_MODE                     0x00be
#define MSK_BIST_VIDEO_MODE_BIST_VIDEO_MODE_3_0 0x0f

/* BIST DURATION0, default value: 0x00 */
#define REG_BIST_DURATION_0                     0x00bf

/* BIST DURATION1, default value: 0x00 */
#define REG_BIST_DURATION_1                     0x00c0

/* BIST DURATION2, default value: 0x00 */
#define REG_BIST_DURATION_2                     0x00c1

/* BIST 8BIT_PATTERN, default value: 0x00 */
#define REG_BIST_8BIT_PATTERN                   0x00c2

/* LM DDC, default value: 0x80 */
#define REG_LM_DDC                              0x00c7
#define BIT_LM_DDC_SW_TPI_EN_DISABLED           BIT(7)

#define BIT_LM_DDC_VIDEO_MUTE_EN                BIT(5)
#define BIT_LM_DDC_DDC_TPI_SW                   BIT(2)
#define BIT_LM_DDC_DDC_GRANT                    BIT(1)
#define BIT_LM_DDC_DDC_GPU_REQUEST              BIT(0)

/* DDC I2C Manual, default value: 0x03 */
#define REG_DDC_MANUAL                          0x00ec
#define BIT_DDC_MANUAL_MAN_DDC                  BIT(7)
#define BIT_DDC_MANUAL_VP_SEL                   BIT(6)
#define BIT_DDC_MANUAL_DSDA                     BIT(5)
#define BIT_DDC_MANUAL_DSCL                     BIT(4)
#define BIT_DDC_MANUAL_GCP_HW_CTL_EN            BIT(3)
#define BIT_DDC_MANUAL_DDCM_ABORT_WP            BIT(2)
#define BIT_DDC_MANUAL_IO_DSDA                  BIT(1)
#define BIT_DDC_MANUAL_IO_DSCL                  BIT(0)

/* DDC I2C Target Slave Address, default value: 0x00 */
#define REG_DDC_ADDR                            0x00ed
#define MSK_DDC_ADDR_DDC_ADDR                   0xfe

/* DDC I2C Target Segment Address, default value: 0x00 */
#define REG_DDC_SEGM                            0x00ee

/* DDC I2C Target Offset Address, default value: 0x00 */
#define REG_DDC_OFFSET                          0x00ef

/* DDC I2C Data In count #1, default value: 0x00 */
#define REG_DDC_DIN_CNT1                        0x00f0

/* DDC I2C Data In count #2, default value: 0x00 */
#define REG_DDC_DIN_CNT2                        0x00f1
#define MSK_DDC_DIN_CNT2_DDC_DIN_CNT_9_8        0x03

/* DDC I2C Status, default value: 0x04 */
#define REG_DDC_STATUS                          0x00f2
#define BIT_DDC_STATUS_DDC_BUS_LOW              BIT(6)
#define BIT_DDC_STATUS_DDC_NO_ACK               BIT(5)
#define BIT_DDC_STATUS_DDC_I2C_IN_PROG          BIT(4)
#define BIT_DDC_STATUS_DDC_FIFO_FULL            BIT(3)
#define BIT_DDC_STATUS_DDC_FIFO_EMPTY           BIT(2)
#define BIT_DDC_STATUS_DDC_FIFO_READ_IN_SUE     BIT(1)
#define BIT_DDC_STATUS_DDC_FIFO_WRITE_IN_USE    BIT(0)

/* DDC I2C Command, default value: 0x70 */
#define REG_DDC_CMD                             0x00f3
#define BIT_DDC_CMD_HDCP_DDC_EN                 BIT(6)
#define BIT_DDC_CMD_SDA_DEL_EN                  BIT(5)
#define BIT_DDC_CMD_DDC_FLT_EN                  BIT(4)

#define MSK_DDC_CMD_DDC_CMD                     0x0f
#define VAL_DDC_CMD_ENH_DDC_READ_NO_ACK         0x04
#define VAL_DDC_CMD_DDC_CMD_CLEAR_FIFO          0x09
#define VAL_DDC_CMD_DDC_CMD_ABORT               0x0f

/* DDC I2C FIFO Data In/Out, default value: 0x00 */
#define REG_DDC_DATA                            0x00f4

/* DDC I2C Data Out Counter, default value: 0x00 */
#define REG_DDC_DOUT_CNT                        0x00f5
#define BIT_DDC_DOUT_CNT_DDC_DELAY_CNT_8        BIT(7)
#define MSK_DDC_DOUT_CNT_DDC_DATA_OUT_CNT       0x1f

/* DDC I2C Delay Count, default value: 0x14 */
#define REG_DDC_DELAY_CNT                       0x00f6

/* Test Control, default value: 0x80 */
#define REG_TEST_TXCTRL                         0x00f7
#define BIT_TEST_TXCTRL_RCLK_REF_SEL            BIT(7)
#define BIT_TEST_TXCTRL_PCLK_REF_SEL            BIT(6)
#define MSK_TEST_TXCTRL_BYPASS_PLL_CLK          0x3c
#define BIT_TEST_TXCTRL_HDMI_MODE               BIT(1)
#define BIT_TEST_TXCTRL_TST_PLLCK               BIT(0)

/* CBUS Address, default value: 0x00 */
#define REG_PAGE_CBUS_ADDR                      0x00f8

/* I2C Device Address re-assignment */
#define REG_PAGE1_ADDR                          0x00fc
#define REG_PAGE2_ADDR                          0x00fd
#define REG_PAGE3_ADDR                          0x00fe
#define REG_HW_TPI_ADDR                         0x00ff

/* USBT CTRL0, default value: 0x00 */
#define REG_UTSRST                              0x0100
#define BIT_UTSRST_FC_SRST                      BIT(5)
#define BIT_UTSRST_KEEPER_SRST                  BIT(4)
#define BIT_UTSRST_HTX_SRST                     BIT(3)
#define BIT_UTSRST_TRX_SRST                     BIT(2)
#define BIT_UTSRST_TTX_SRST                     BIT(1)
#define BIT_UTSRST_HRX_SRST                     BIT(0)

/* HSIC RX Control3, default value: 0x07 */
#define REG_HRXCTRL3                            0x0104
#define MSK_HRXCTRL3_HRX_AFFCTRL                0xf0
#define BIT_HRXCTRL3_HRX_OUT_EN                 BIT(2)
#define BIT_HRXCTRL3_STATUS_EN                  BIT(1)
#define BIT_HRXCTRL3_HRX_STAY_RESET             BIT(0)

/* HSIC RX INT Registers */
#define REG_HRXINTL                             0x0111
#define REG_HRXINTH                             0x0112

/* TDM TX NUMBITS, default value: 0x0c */
#define REG_TTXNUMB                             0x0116
#define MSK_TTXNUMB_TTX_AFFCTRL_3_0             0xf0
#define BIT_TTXNUMB_TTX_COM1_AT_SYNC_WAIT       BIT(3)
#define MSK_TTXNUMB_TTX_NUMBPS                  0x07

/* TDM TX NUMSPISYM, default value: 0x04 */
#define REG_TTXSPINUMS                          0x0117

/* TDM TX NUMHSICSYM, default value: 0x14 */
#define REG_TTXHSICNUMS                         0x0118

/* TDM TX NUMTOTSYM, default value: 0x18 */
#define REG_TTXTOTNUMS                          0x0119

/* TDM TX INT Low, default value: 0x00 */
#define REG_TTXINTL                             0x0136
#define BIT_TTXINTL_TTX_INTR7                   BIT(7)
#define BIT_TTXINTL_TTX_INTR6                   BIT(6)
#define BIT_TTXINTL_TTX_INTR5                   BIT(5)
#define BIT_TTXINTL_TTX_INTR4                   BIT(4)
#define BIT_TTXINTL_TTX_INTR3                   BIT(3)
#define BIT_TTXINTL_TTX_INTR2                   BIT(2)
#define BIT_TTXINTL_TTX_INTR1                   BIT(1)
#define BIT_TTXINTL_TTX_INTR0                   BIT(0)

/* TDM TX INT High, default value: 0x00 */
#define REG_TTXINTH                             0x0137
#define BIT_TTXINTH_TTX_INTR15                  BIT(7)
#define BIT_TTXINTH_TTX_INTR14                  BIT(6)
#define BIT_TTXINTH_TTX_INTR13                  BIT(5)
#define BIT_TTXINTH_TTX_INTR12                  BIT(4)
#define BIT_TTXINTH_TTX_INTR11                  BIT(3)
#define BIT_TTXINTH_TTX_INTR10                  BIT(2)
#define BIT_TTXINTH_TTX_INTR9                   BIT(1)
#define BIT_TTXINTH_TTX_INTR8                   BIT(0)

/* TDM RX Control, default value: 0x1c */
#define REG_TRXCTRL                             0x013b
#define BIT_TRXCTRL_TRX_CLR_WVALLOW             BIT(4)
#define BIT_TRXCTRL_TRX_FROM_SE_COC             BIT(3)
#define MSK_TRXCTRL_TRX_NUMBPS_2_0              0x07

/* TDM RX NUMSPISYM, default value: 0x04 */
#define REG_TRXSPINUMS                          0x013c

/* TDM RX NUMHSICSYM, default value: 0x14 */
#define REG_TRXHSICNUMS                         0x013d

/* TDM RX NUMTOTSYM, default value: 0x18 */
#define REG_TRXTOTNUMS                          0x013e

/* TDM RX Status 2nd, default value: 0x00 */
#define REG_TRXSTA2                             0x015c
#define MSK_TDM_SYNCHRONIZED                    0xc0
#define VAL_TDM_SYNCHRONIZED                    0x80

/* TDM RX INT Low, default value: 0x00 */
#define REG_TRXINTL                             0x0163

/* TDM RX INT High, default value: 0x00 */
#define REG_TRXINTH                             0x0164
#define BIT_TDM_INTR_SYNC_DATA                  BIT(0)
#define BIT_TDM_INTR_SYNC_WAIT                  BIT(1)

/* TDM RX INTMASK High, default value: 0x00 */
#define REG_TRXINTMH                            0x0166

/* HSIC TX CRTL, default value: 0x00 */
#define REG_HTXCTRL                             0x0169
#define BIT_HTXCTRL_HTX_ALLSBE_SOP              BIT(4)
#define BIT_HTXCTRL_HTX_RGDINV_USB              BIT(3)
#define BIT_HTXCTRL_HTX_RSPTDM_BUSY             BIT(2)
#define BIT_HTXCTRL_HTX_DRVCONN1                BIT(1)
#define BIT_HTXCTRL_HTX_DRVRST1                 BIT(0)

/* HSIC TX INT Low, default value: 0x00 */
#define REG_HTXINTL                             0x017d

/* HSIC TX INT High, default value: 0x00 */
#define REG_HTXINTH                             0x017e

/* HSIC Keeper, default value: 0x00 */
#define REG_KEEPER                              0x0181
#define MSK_KEEPER_MODE                         0x03
#define VAL_KEEPER_MODE_HOST                    0
#define VAL_KEEPER_MODE_DEVICE                  2

/* HSIC Flow Control General, default value: 0x02 */
#define REG_FCGC                                0x0183
#define BIT_FCGC_HSIC_HOSTMODE                  BIT(1)
#define BIT_FCGC_HSIC_ENABLE                    BIT(0)

/* HSIC Flow Control CTR13, default value: 0xfc */
#define REG_FCCTR13                             0x0191

/* HSIC Flow Control CTR14, default value: 0xff */
#define REG_FCCTR14                             0x0192

/* HSIC Flow Control CTR15, default value: 0xff */
#define REG_FCCTR15                             0x0193

/* HSIC Flow Control CTR50, default value: 0x03 */
#define REG_FCCTR50                             0x01b6

/* HSIC Flow Control INTR0, default value: 0x00 */
#define REG_FCINTR0                             0x01ec
#define REG_FCINTR1                             0x01ed
#define REG_FCINTR2                             0x01ee
#define REG_FCINTR3                             0x01ef
#define REG_FCINTR4                             0x01f0
#define REG_FCINTR5                             0x01f1
#define REG_FCINTR6                             0x01f2
#define REG_FCINTR7                             0x01f3

/* TDM Low Latency, default value: 0x20 */
#define REG_TDMLLCTL                            0x01fc
#define MSK_TDMLLCTL_TRX_LL_SEL_MANUAL          0xc0
#define MSK_TDMLLCTL_TRX_LL_SEL_MODE            0x30
#define MSK_TDMLLCTL_TTX_LL_SEL_MANUAL          0x0c
#define BIT_TDMLLCTL_TTX_LL_TIE_LOW             BIT(1)
#define BIT_TDMLLCTL_TTX_LL_SEL_MODE            BIT(0)

/* TMDS 0 Clock Control, default value: 0x10 */
#define REG_TMDS0_CCTRL1                        0x0210
#define MSK_TMDS0_CCTRL1_TEST_SEL               0xc0
#define MSK_TMDS0_CCTRL1_CLK1X_CTL              0x30

/* TMDS Clock Enable, default value: 0x00 */
#define REG_TMDS_CLK_EN                         0x0211
#define BIT_TMDS_CLK_EN_CLK_EN                  BIT(0)

/* TMDS Channel Enable, default value: 0x00 */
#define REG_TMDS_CH_EN                          0x0212
#define BIT_TMDS_CH_EN_CH0_EN                   BIT(4)
#define BIT_TMDS_CH_EN_CH12_EN                  BIT(0)

/* BGR_BIAS, default value: 0x07 */
#define REG_BGR_BIAS                            0x0215
#define BIT_BGR_BIAS_BGR_EN                     BIT(7)
#define MSK_BGR_BIAS_BIAS_BGR_D                 0x0f

/* TMDS 0 Digital I2C BW, default value: 0x0a */
#define REG_ALICE0_BW_I2C                       0x0231

/* TMDS 0 Digital Zone Control, default value: 0xe0 */
#define REG_ALICE0_ZONE_CTRL                    0x024c
#define BIT_ALICE0_ZONE_CTRL_ICRST_N            BIT(7)
#define BIT_ALICE0_ZONE_CTRL_USE_INT_DIV20      BIT(6)
#define MSK_ALICE0_ZONE_CTRL_SZONE_I2C          0x30
#define MSK_ALICE0_ZONE_CTRL_ZONE_CTRL          0x0f

/* TMDS 0 Digital PLL Mode Control, default value: 0x00 */
#define REG_ALICE0_MODE_CTRL                    0x024d
#define MSK_ALICE0_MODE_CTRL_PLL_MODE_I2C       0x0c
#define MSK_ALICE0_MODE_CTRL_DIV20_CTRL         0x03

/* MHL Tx Control 6th, default value: 0xa0 */
#define REG_MHLTX_CTL6                          0x0285
#define MSK_MHLTX_CTL6_EMI_SEL                  0xe0
#define MSK_MHLTX_CTL6_TX_CLK_SHAPE_9_8         0x03

/* Packet Filter0, default value: 0x00 */
#define REG_PKT_FILTER_0                        0x0290
#define BIT_PKT_FILTER_0_DROP_CEA_GAMUT_PKT     BIT(7)
#define BIT_PKT_FILTER_0_DROP_CEA_CP_PKT        BIT(6)
#define BIT_PKT_FILTER_0_DROP_MPEG_PKT          BIT(5)
#define BIT_PKT_FILTER_0_DROP_SPIF_PKT          BIT(4)
#define BIT_PKT_FILTER_0_DROP_AIF_PKT           BIT(3)
#define BIT_PKT_FILTER_0_DROP_AVI_PKT           BIT(2)
#define BIT_PKT_FILTER_0_DROP_CTS_PKT           BIT(1)
#define BIT_PKT_FILTER_0_DROP_GCP_PKT           BIT(0)

/* Packet Filter1, default value: 0x00 */
#define REG_PKT_FILTER_1                        0x0291
#define BIT_PKT_FILTER_1_VSI_OVERRIDE_DIS       BIT(7)
#define BIT_PKT_FILTER_1_AVI_OVERRIDE_DIS       BIT(6)
#define BIT_PKT_FILTER_1_DROP_AUDIO_PKT         BIT(3)
#define BIT_PKT_FILTER_1_DROP_GEN2_PKT          BIT(2)
#define BIT_PKT_FILTER_1_DROP_GEN_PKT           BIT(1)
#define BIT_PKT_FILTER_1_DROP_VSIF_PKT          BIT(0)

/* TMDS Clock Status, default value: 0x10 */
#define REG_TMDS_CSTAT_P3                       0x02a0
#define BIT_TMDS_CSTAT_P3_RX_HDMI_CP_CLR_MUTE   BIT(7)
#define BIT_TMDS_CSTAT_P3_RX_HDMI_CP_SET_MUTE   BIT(6)
#define BIT_TMDS_CSTAT_P3_RX_HDMI_CP_NEW_CP     BIT(5)
#define BIT_TMDS_CSTAT_P3_CLR_AVI               BIT(3)
#define BIT_TMDS_CSTAT_P3_SCDT_CLR_AVI_DIS      BIT(2)
#define BIT_TMDS_CSTAT_P3_SCDT                  BIT(1)
#define BIT_TMDS_CSTAT_P3_CKDT                  BIT(0)

/* RX_HDMI Control, default value: 0x10 */
#define REG_RX_HDMI_CTRL0                       0x02a1
#define BIT_RX_HDMI_CTRL0_BYP_DVIFILT_SYNC      BIT(5)
#define BIT_RX_HDMI_CTRL0_HDMI_MODE_EN_ITSELF_CLR BIT(4)
#define BIT_RX_HDMI_CTRL0_HDMI_MODE_SW_VALUE    BIT(3)
#define BIT_RX_HDMI_CTRL0_HDMI_MODE_OVERWRITE   BIT(2)
#define BIT_RX_HDMI_CTRL0_RX_HDMI_HDMI_MODE_EN  BIT(1)
#define BIT_RX_HDMI_CTRL0_RX_HDMI_HDMI_MODE     BIT(0)

/* RX_HDMI Control, default value: 0x38 */
#define REG_RX_HDMI_CTRL2                       0x02a3
#define MSK_RX_HDMI_CTRL2_IDLE_CNT              0xf0
#define VAL_RX_HDMI_CTRL2_IDLE_CNT(n)           ((n) << 4)
#define BIT_RX_HDMI_CTRL2_USE_AV_MUTE           BIT(3)
#define BIT_RX_HDMI_CTRL2_VSI_MON_SEL_VSI       BIT(0)

/* RX_HDMI Control, default value: 0x0f */
#define REG_RX_HDMI_CTRL3                       0x02a4
#define MSK_RX_HDMI_CTRL3_PP_MODE_CLK_EN        0x0f

/* rx_hdmi Clear Buffer, default value: 0x00 */
#define REG_RX_HDMI_CLR_BUFFER                  0x02ac
#define MSK_RX_HDMI_CLR_BUFFER_AIF4VSI_CMP      0xc0
#define BIT_RX_HDMI_CLR_BUFFER_USE_AIF4VSI      BIT(5)
#define BIT_RX_HDMI_CLR_BUFFER_VSI_CLR_W_AVI    BIT(4)
#define BIT_RX_HDMI_CLR_BUFFER_VSI_IEEE_ID_CHK_EN BIT(3)
#define BIT_RX_HDMI_CLR_BUFFER_SWAP_VSI_IEEE_ID BIT(2)
#define BIT_RX_HDMI_CLR_BUFFER_AIF_CLR_EN       BIT(1)
#define BIT_RX_HDMI_CLR_BUFFER_VSI_CLR_EN       BIT(0)

/* RX_HDMI VSI Header1, default value: 0x00 */
#define REG_RX_HDMI_MON_PKT_HEADER1             0x02b8

/* RX_HDMI VSI MHL Monitor, default value: 0x3c */
#define REG_RX_HDMI_VSIF_MHL_MON                0x02d7

#define MSK_RX_HDMI_VSIF_MHL_MON_RX_HDMI_MHL_3D_FORMAT 0x3c
#define MSK_RX_HDMI_VSIF_MHL_MON_RX_HDMI_MHL_VID_FORMAT 0x03

/* Interrupt Source 9, default value: 0x00 */
#define REG_INTR9                               0x02e0
#define BIT_INTR9_EDID_ERROR                    BIT(6)
#define BIT_INTR9_EDID_DONE                     BIT(5)
#define BIT_INTR9_DEVCAP_DONE                   BIT(4)

/* Interrupt 9 Mask, default value: 0x00 */
#define REG_INTR9_MASK                          0x02e1

/* TPI CBUS Start, default value: 0x00 */
#define REG_TPI_CBUS_START                      0x02e2
#define BIT_TPI_CBUS_START_RCP_REQ_START        BIT(7)
#define BIT_TPI_CBUS_START_RCPK_REPLY_START     BIT(6)
#define BIT_TPI_CBUS_START_RCPE_REPLY_START     BIT(5)
#define BIT_TPI_CBUS_START_PUT_LINK_MODE_START  BIT(4)
#define BIT_TPI_CBUS_START_PUT_DCAPCHG_START    BIT(3)
#define BIT_TPI_CBUS_START_PUT_DCAPRDY_START    BIT(2)
#define BIT_TPI_CBUS_START_GET_EDID_START_0     BIT(1)
#define BIT_TPI_CBUS_START_GET_DEVCAP_START     BIT(0)

/* EDID Control, default value: 0x10 */
#define REG_EDID_CTRL                           0x02e3
#define BIT_EDID_CTRL_EDID_PRIME_VALID          BIT(7)
#define BIT_EDID_CTRL_XDEVCAP_EN                BIT(6)
#define BIT_EDID_CTRL_DEVCAP_SELECT_DEVCAP      BIT(5)
#define BIT_EDID_CTRL_EDID_FIFO_ADDR_AUTO       BIT(4)
#define BIT_EDID_CTRL_EDID_FIFO_ACCESS_ALWAYS_EN BIT(3)
#define BIT_EDID_CTRL_EDID_FIFO_BLOCK_SEL       BIT(2)
#define BIT_EDID_CTRL_INVALID_BKSV              BIT(1)
#define BIT_EDID_CTRL_EDID_MODE_EN              BIT(0)

/* EDID FIFO Addr, default value: 0x00 */
#define REG_EDID_FIFO_ADDR                      0x02e9

/* EDID FIFO Write Data, default value: 0x00 */
#define REG_EDID_FIFO_WR_DATA                   0x02ea

/* EDID/DEVCAP FIFO Internal Addr, default value: 0x00 */
#define REG_EDID_FIFO_ADDR_MON                  0x02eb

/* EDID FIFO Read Data, default value: 0x00 */
#define REG_EDID_FIFO_RD_DATA                   0x02ec

/* EDID DDC Segment Pointer, default value: 0x00 */
#define REG_EDID_START_EXT                      0x02ed

/* TX IP BIST CNTL and Status, default value: 0x00 */
#define REG_TX_IP_BIST_CNTLSTA                  0x02f2
#define BIT_TX_IP_BIST_CNTLSTA_TXBIST_QUARTER_CLK_SEL BIT(6)
#define BIT_TX_IP_BIST_CNTLSTA_TXBIST_DONE      BIT(5)
#define BIT_TX_IP_BIST_CNTLSTA_TXBIST_ON        BIT(4)
#define BIT_TX_IP_BIST_CNTLSTA_TXBIST_RUN       BIT(3)
#define BIT_TX_IP_BIST_CNTLSTA_TXCLK_HALF_SEL   BIT(2)
#define BIT_TX_IP_BIST_CNTLSTA_TXBIST_EN        BIT(1)
#define BIT_TX_IP_BIST_CNTLSTA_TXBIST_SEL       BIT(0)

/* TX IP BIST INST LOW, default value: 0x00 */
#define REG_TX_IP_BIST_INST_LOW                 0x02f3
#define REG_TX_IP_BIST_INST_HIGH                0x02f4

/* TX IP BIST PATTERN LOW, default value: 0x00 */
#define REG_TX_IP_BIST_PAT_LOW                  0x02f5
#define REG_TX_IP_BIST_PAT_HIGH                 0x02f6

/* TX IP BIST CONFIGURE LOW, default value: 0x00 */
#define REG_TX_IP_BIST_CONF_LOW                 0x02f7
#define REG_TX_IP_BIST_CONF_HIGH                0x02f8

/* E-MSC General Control, default value: 0x80 */
#define REG_GENCTL                              0x0300
#define BIT_GENCTL_SPEC_TRANS_DIS               BIT(7)
#define BIT_GENCTL_DIS_XMIT_ERR_STATE           BIT(6)
#define BIT_GENCTL_SPI_MISO_EDGE                BIT(5)
#define BIT_GENCTL_SPI_MOSI_EDGE                BIT(4)
#define BIT_GENCTL_CLR_EMSC_RFIFO               BIT(3)
#define BIT_GENCTL_CLR_EMSC_XFIFO               BIT(2)
#define BIT_GENCTL_START_TRAIN_SEQ              BIT(1)
#define BIT_GENCTL_EMSC_EN                      BIT(0)

/* E-MSC Comma ErrorCNT, default value: 0x03 */
#define REG_COMMECNT                            0x0305
#define BIT_COMMECNT_I2C_TO_EMSC_EN             BIT(7)
#define MSK_COMMECNT_COMMA_CHAR_ERR_CNT         0x0f

/* E-MSC RFIFO ByteCnt, default value: 0x00 */
#define REG_EMSCRFIFOBCNTL                      0x031a
#define REG_EMSCRFIFOBCNTH                      0x031b

/* SPI Burst Cnt Status, default value: 0x00 */
#define REG_SPIBURSTCNT                         0x031e

/* SPI Burst Status and SWRST, default value: 0x00 */
#define REG_SPIBURSTSTAT                        0x0322
#define BIT_SPIBURSTSTAT_SPI_HDCPRST            BIT(7)
#define BIT_SPIBURSTSTAT_SPI_CBUSRST            BIT(6)
#define BIT_SPIBURSTSTAT_SPI_SRST               BIT(5)
#define BIT_SPIBURSTSTAT_EMSC_NORMAL_MODE       BIT(0)

/* E-MSC 1st Interrupt, default value: 0x00 */
#define REG_EMSCINTR                            0x0323
#define BIT_EMSCINTR_EMSC_XFIFO_EMPTY           BIT(7)
#define BIT_EMSCINTR_EMSC_XMIT_ACK_TOUT         BIT(6)
#define BIT_EMSCINTR_EMSC_RFIFO_READ_ERR        BIT(5)
#define BIT_EMSCINTR_EMSC_XFIFO_WRITE_ERR       BIT(4)
#define BIT_EMSCINTR_EMSC_COMMA_CHAR_ERR        BIT(3)
#define BIT_EMSCINTR_EMSC_XMIT_DONE             BIT(2)
#define BIT_EMSCINTR_EMSC_XMIT_GNT_TOUT         BIT(1)
#define BIT_EMSCINTR_SPI_DVLD           BIT(0)

/* E-MSC Interrupt Mask, default value: 0x00 */
#define REG_EMSCINTRMASK                        0x0324

/* I2C E-MSC XMIT FIFO Write Port, default value: 0x00 */
#define REG_EMSC_XMIT_WRITE_PORT                0x032a

/* I2C E-MSC RCV FIFO Write Port, default value: 0x00 */
#define REG_EMSC_RCV_READ_PORT                  0x032b

/* E-MSC 2nd Interrupt, default value: 0x00 */
#define REG_EMSCINTR1                           0x032c
#define BIT_EMSCINTR1_EMSC_TRAINING_COMMA_ERR   BIT(0)

/* E-MSC Interrupt Mask, default value: 0x00 */
#define REG_EMSCINTRMASK1                       0x032d
#define BIT_EMSCINTRMASK1_EMSC_INTRMASK1_0      BIT(0)

/* MHL Top Ctl, default value: 0x00 */
#define REG_MHL_TOP_CTL                         0x0330
#define BIT_MHL_TOP_CTL_MHL3_DOC_SEL            BIT(7)
#define BIT_MHL_TOP_CTL_MHL_PP_SEL              BIT(6)
#define MSK_MHL_TOP_CTL_IF_TIMING_CTL           0x03

/* MHL DataPath 1st Ctl, default value: 0xbc */
#define REG_MHL_DP_CTL0                         0x0331
#define BIT_MHL_DP_CTL0_DP_OE                   BIT(7)
#define BIT_MHL_DP_CTL0_TX_OE_OVR               BIT(6)
#define MSK_MHL_DP_CTL0_TX_OE                   0x3f

/* MHL DataPath 2nd Ctl, default value: 0xbb */
#define REG_MHL_DP_CTL1                         0x0332
#define MSK_MHL_DP_CTL1_CK_SWING_CTL            0xf0
#define MSK_MHL_DP_CTL1_DT_SWING_CTL            0x0f

/* MHL DataPath 3rd Ctl, default value: 0x2f */
#define REG_MHL_DP_CTL2                         0x0333
#define BIT_MHL_DP_CTL2_CLK_BYPASS_EN           BIT(7)
#define MSK_MHL_DP_CTL2_DAMP_TERM_SEL           0x30
#define MSK_MHL_DP_CTL2_CK_TERM_SEL             0x0c
#define MSK_MHL_DP_CTL2_DT_TERM_SEL             0x03

/* MHL DataPath 4th Ctl, default value: 0x48 */
#define REG_MHL_DP_CTL3                         0x0334
#define MSK_MHL_DP_CTL3_DT_DRV_VNBC_CTL         0xf0
#define MSK_MHL_DP_CTL3_DT_DRV_VNB_CTL          0x0f

/* MHL DataPath 5th Ctl, default value: 0x48 */
#define REG_MHL_DP_CTL4                         0x0335
#define MSK_MHL_DP_CTL4_CK_DRV_VNBC_CTL         0xf0
#define MSK_MHL_DP_CTL4_CK_DRV_VNB_CTL          0x0f

/* MHL DataPath 6th Ctl, default value: 0x3f */
#define REG_MHL_DP_CTL5                         0x0336
#define BIT_MHL_DP_CTL5_RSEN_EN_OVR             BIT(7)
#define BIT_MHL_DP_CTL5_RSEN_EN                 BIT(6)
#define MSK_MHL_DP_CTL5_DAMP_TERM_VGS_CTL       0x30
#define MSK_MHL_DP_CTL5_CK_TERM_VGS_CTL         0x0c
#define MSK_MHL_DP_CTL5_DT_TERM_VGS_CTL         0x03

/* MHL PLL 1st Ctl, default value: 0x05 */
#define REG_MHL_PLL_CTL0                        0x0337
#define BIT_MHL_PLL_CTL0_AUD_CLK_EN             BIT(7)

#define MSK_MHL_PLL_CTL0_AUD_CLK_RATIO          0x70
#define VAL_MHL_PLL_CTL0_AUD_CLK_RATIO_5_10     0x70
#define VAL_MHL_PLL_CTL0_AUD_CLK_RATIO_5_6      0x60
#define VAL_MHL_PLL_CTL0_AUD_CLK_RATIO_5_4      0x50
#define VAL_MHL_PLL_CTL0_AUD_CLK_RATIO_5_2      0x40
#define VAL_MHL_PLL_CTL0_AUD_CLK_RATIO_5_5      0x30
#define VAL_MHL_PLL_CTL0_AUD_CLK_RATIO_5_3      0x20
#define VAL_MHL_PLL_CTL0_AUD_CLK_RATIO_5_2_PRIME 0x10
#define VAL_MHL_PLL_CTL0_AUD_CLK_RATIO_5_1      0x00

#define MSK_MHL_PLL_CTL0_HDMI_CLK_RATIO         0x0c
#define VAL_MHL_PLL_CTL0_HDMI_CLK_RATIO_4X      0x0c
#define VAL_MHL_PLL_CTL0_HDMI_CLK_RATIO_2X      0x08
#define VAL_MHL_PLL_CTL0_HDMI_CLK_RATIO_1X      0x04
#define VAL_MHL_PLL_CTL0_HDMI_CLK_RATIO_HALF_X  0x00

#define BIT_MHL_PLL_CTL0_CRYSTAL_CLK_SEL        BIT(1)
#define BIT_MHL_PLL_CTL0_ZONE_MASK_OE           BIT(0)

/* MHL PLL 3rd Ctl, default value: 0x80 */
#define REG_MHL_PLL_CTL2                        0x0339
#define BIT_MHL_PLL_CTL2_CLKDETECT_EN           BIT(7)
#define BIT_MHL_PLL_CTL2_MEAS_FVCO              BIT(3)
#define BIT_MHL_PLL_CTL2_PLL_FAST_LOCK          BIT(2)
#define MSK_MHL_PLL_CTL2_PLL_LF_SEL             0x03

/* MHL CBUS 1st Ctl, default value: 0x12 */
#define REG_MHL_CBUS_CTL0                       0x0340
#define BIT_MHL_CBUS_CTL0_CBUS_RGND_TEST_MODE   BIT(7)

#define MSK_MHL_CBUS_CTL0_CBUS_RGND_VTH_CTL     0x30
#define VAL_MHL_CBUS_CTL0_CBUS_RGND_VBIAS_734   0x00
#define VAL_MHL_CBUS_CTL0_CBUS_RGND_VBIAS_747   0x10
#define VAL_MHL_CBUS_CTL0_CBUS_RGND_VBIAS_740   0x20
#define VAL_MHL_CBUS_CTL0_CBUS_RGND_VBIAS_754   0x30

#define MSK_MHL_CBUS_CTL0_CBUS_RES_TEST_SEL     0x0c

#define MSK_MHL_CBUS_CTL0_CBUS_DRV_SEL          0x03
#define VAL_MHL_CBUS_CTL0_CBUS_DRV_SEL_WEAKEST  0x00
#define VAL_MHL_CBUS_CTL0_CBUS_DRV_SEL_WEAK     0x01
#define VAL_MHL_CBUS_CTL0_CBUS_DRV_SEL_STRONG   0x02
#define VAL_MHL_CBUS_CTL0_CBUS_DRV_SEL_STRONGEST 0x03

/* MHL CBUS 2nd Ctl, default value: 0x03 */
#define REG_MHL_CBUS_CTL1                       0x0341
#define MSK_MHL_CBUS_CTL1_CBUS_RGND_RES_CTL     0x07
#define VAL_MHL_CBUS_CTL1_0888_OHM              0x00
#define VAL_MHL_CBUS_CTL1_1115_OHM              0x04
#define VAL_MHL_CBUS_CTL1_1378_OHM              0x07

/* MHL CoC 1st Ctl, default value: 0xc3 */
#define REG_MHL_COC_CTL0                        0x0342
#define BIT_MHL_COC_CTL0_COC_BIAS_EN            BIT(7)
#define MSK_MHL_COC_CTL0_COC_BIAS_CTL           0x70
#define MSK_MHL_COC_CTL0_COC_TERM_CTL           0x07

/* MHL CoC 2nd Ctl, default value: 0x87 */
#define REG_MHL_COC_CTL1                        0x0343
#define BIT_MHL_COC_CTL1_COC_EN                 BIT(7)
#define MSK_MHL_COC_CTL1_COC_DRV_CTL            0x3f

/* MHL CoC 4th Ctl, default value: 0x00 */
#define REG_MHL_COC_CTL3                        0x0345
#define BIT_MHL_COC_CTL3_COC_AECHO_EN           BIT(0)

/* MHL CoC 5th Ctl, default value: 0x28 */
#define REG_MHL_COC_CTL4                        0x0346
#define MSK_MHL_COC_CTL4_COC_IF_CTL             0xf0
#define MSK_MHL_COC_CTL4_COC_SLEW_CTL           0x0f

/* MHL CoC 6th Ctl, default value: 0x0d */
#define REG_MHL_COC_CTL5                        0x0347

/* MHL DoC 1st Ctl, default value: 0x18 */
#define REG_MHL_DOC_CTL0                        0x0349
#define BIT_MHL_DOC_CTL0_DOC_RXDATA_EN          BIT(7)
#define MSK_MHL_DOC_CTL0_DOC_DM_TERM            0x38
#define MSK_MHL_DOC_CTL0_DOC_OPMODE             0x06
#define BIT_MHL_DOC_CTL0_DOC_RXBIAS_EN          BIT(0)

/* MHL DataPath 7th Ctl, default value: 0x2a */
#define REG_MHL_DP_CTL6                         0x0350
#define BIT_MHL_DP_CTL6_DP_TAP2_SGN             BIT(5)
#define BIT_MHL_DP_CTL6_DP_TAP2_EN              BIT(4)
#define BIT_MHL_DP_CTL6_DP_TAP1_SGN             BIT(3)
#define BIT_MHL_DP_CTL6_DP_TAP1_EN              BIT(2)
#define BIT_MHL_DP_CTL6_DT_PREDRV_FEEDCAP_EN    BIT(1)
#define BIT_MHL_DP_CTL6_DP_PRE_POST_SEL         BIT(0)

/* MHL DataPath 8th Ctl, default value: 0x06 */
#define REG_MHL_DP_CTL7                         0x0351
#define MSK_MHL_DP_CTL7_DT_DRV_VBIAS_CASCTL     0xf0
#define MSK_MHL_DP_CTL7_DT_DRV_IREF_CTL         0x0f

#define REG_MHL_DP_CTL8                         0x0352

/* Tx Zone Ctl1, default value: 0x00 */
#define REG_TX_ZONE_CTL1                        0x0361
#define VAL_TX_ZONE_CTL1_TX_ZONE_CTRL_MODE      0x08

/* MHL3 Tx Zone Ctl, default value: 0x00 */
#define REG_MHL3_TX_ZONE_CTL                    0x0364
#define BIT_MHL3_TX_ZONE_CTL_MHL2_INTPLT_ZONE_MANU_EN BIT(7)
#define MSK_MHL3_TX_ZONE_CTL_MHL3_TX_ZONE       0x03

#define MSK_TX_ZONE_CTL3_TX_ZONE                0x03
#define VAL_TX_ZONE_CTL3_TX_ZONE_6GBPS          0x00
#define VAL_TX_ZONE_CTL3_TX_ZONE_3GBPS          0x01
#define VAL_TX_ZONE_CTL3_TX_ZONE_1_5GBPS        0x02

/* HDCP Polling Control and Status, default value: 0x70 */
#define REG_HDCP2X_POLL_CS                      0x0391

#define BIT_HDCP2X_POLL_CS_HDCP2X_MSG_SZ_CLR_OPTION BIT(6)
#define BIT_HDCP2X_POLL_CS_HDCP2X_RPT_READY_CLR_OPTION BIT(5)
#define BIT_HDCP2X_POLL_CS_HDCP2X_REAUTH_REQ_CLR_OPTION BIT(4)
#define MSK_HDCP2X_POLL_CS_                     0x0c
#define BIT_HDCP2X_POLL_CS_HDCP2X_DIS_POLL_GNT  BIT(1)
#define BIT_HDCP2X_POLL_CS_HDCP2X_DIS_POLL_EN   BIT(0)

/* HDCP Interrupt 0, default value: 0x00 */
#define REG_HDCP2X_INTR0                        0x0398

/* HDCP Interrupt 0 Mask, default value: 0x00 */
#define REG_HDCP2X_INTR0_MASK                   0x0399

/* HDCP General Control 0, default value: 0x02 */
#define REG_HDCP2X_CTRL_0                       0x03a0
#define BIT_HDCP2X_CTRL_0_HDCP2X_ENCRYPT_EN     BIT(7)
#define BIT_HDCP2X_CTRL_0_HDCP2X_POLINT_SEL     BIT(6)
#define BIT_HDCP2X_CTRL_0_HDCP2X_POLINT_OVR     BIT(5)
#define BIT_HDCP2X_CTRL_0_HDCP2X_PRECOMPUTE     BIT(4)
#define BIT_HDCP2X_CTRL_0_HDCP2X_HDMIMODE       BIT(3)
#define BIT_HDCP2X_CTRL_0_HDCP2X_REPEATER       BIT(2)
#define BIT_HDCP2X_CTRL_0_HDCP2X_HDCPTX         BIT(1)
#define BIT_HDCP2X_CTRL_0_HDCP2X_EN             BIT(0)

/* HDCP General Control 1, default value: 0x08 */
#define REG_HDCP2X_CTRL_1                       0x03a1
#define MSK_HDCP2X_CTRL_1_HDCP2X_REAUTH_MSK_3_0 0xf0
#define BIT_HDCP2X_CTRL_1_HDCP2X_HPD_SW         BIT(3)
#define BIT_HDCP2X_CTRL_1_HDCP2X_HPD_OVR        BIT(2)
#define BIT_HDCP2X_CTRL_1_HDCP2X_CTL3MSK        BIT(1)
#define BIT_HDCP2X_CTRL_1_HDCP2X_REAUTH_SW      BIT(0)

/* HDCP Misc Control, default value: 0x00 */
#define REG_HDCP2X_MISC_CTRL                    0x03a5
#define BIT_HDCP2X_MISC_CTRL_HDCP2X_RPT_SMNG_XFER_START BIT(4)
#define BIT_HDCP2X_MISC_CTRL_HDCP2X_RPT_SMNG_WR_START BIT(3)
#define BIT_HDCP2X_MISC_CTRL_HDCP2X_RPT_SMNG_WR BIT(2)
#define BIT_HDCP2X_MISC_CTRL_HDCP2X_RPT_RCVID_RD_START BIT(1)
#define BIT_HDCP2X_MISC_CTRL_HDCP2X_RPT_RCVID_RD        BIT(0)

/* HDCP RPT SMNG K, default value: 0x00 */
#define REG_HDCP2X_RPT_SMNG_K                   0x03a6

/* HDCP RPT SMNG In, default value: 0x00 */
#define REG_HDCP2X_RPT_SMNG_IN                  0x03a7

/* HDCP Auth Status, default value: 0x00 */
#define REG_HDCP2X_AUTH_STAT                    0x03aa

/* HDCP RPT RCVID Out, default value: 0x00 */
#define REG_HDCP2X_RPT_RCVID_OUT                0x03ac

/* HDCP TP1, default value: 0x62 */
#define REG_HDCP2X_TP1                          0x03b4

/* HDCP GP Out 0, default value: 0x00 */
#define REG_HDCP2X_GP_OUT0                      0x03c7

/* HDCP Repeater RCVR ID 0, default value: 0x00 */
#define REG_HDCP2X_RPT_RCVR_ID0                 0x03d1

/* HDCP DDCM Status, default value: 0x00 */
#define REG_HDCP2X_DDCM_STS                     0x03d8
#define MSK_HDCP2X_DDCM_STS_HDCP2X_DDCM_ERR_STS_3_0 0xf0
#define MSK_HDCP2X_DDCM_STS_HDCP2X_DDCM_CTL_CS_3_0 0x0f

/* HDMI2MHL3 Control, default value: 0x0a */
#define REG_M3_CTRL                             0x03e0
#define BIT_M3_CTRL_H2M_SWRST                   BIT(4)
#define BIT_M3_CTRL_SW_MHL3_SEL                 BIT(3)
#define BIT_M3_CTRL_M3AV_EN                     BIT(2)
#define BIT_M3_CTRL_ENC_TMDS                    BIT(1)
#define BIT_M3_CTRL_MHL3_MASTER_EN              BIT(0)

#define VAL_M3_CTRL_MHL1_2_VALUE (BIT_M3_CTRL_SW_MHL3_SEL \
                                  | BIT_M3_CTRL_ENC_TMDS)
#define VAL_M3_CTRL_MHL3_VALUE (BIT_M3_CTRL_SW_MHL3_SEL \
                                | BIT_M3_CTRL_M3AV_EN \
                                | BIT_M3_CTRL_ENC_TMDS \
                                | BIT_M3_CTRL_MHL3_MASTER_EN)

/* HDMI2MHL3 Port0 Control, default value: 0x04 */
#define REG_M3_P0CTRL                           0x03e1
#define BIT_M3_P0CTRL_MHL3_P0_HDCP_ENC_EN       BIT(4)
#define BIT_M3_P0CTRL_MHL3_P0_UNLIMIT_EN        BIT(3)
#define BIT_M3_P0CTRL_MHL3_P0_HDCP_EN           BIT(2)
#define BIT_M3_P0CTRL_MHL3_P0_PIXEL_MODE_PACKED BIT(1)
#define BIT_M3_P0CTRL_MHL3_P0_PORT_EN           BIT(0)

#define REG_M3_POSTM                            0x03e2
#define MSK_M3_POSTM_RRP_DECODE                 0xf8
#define MSK_M3_POSTM_MHL3_P0_STM_ID             0x07

/* HDMI2MHL3 Scramble Control, default value: 0x41 */
#define REG_M3_SCTRL                            0x03e6
#define MSK_M3_SCTRL_MHL3_SR_LENGTH             0xf0
#define BIT_M3_SCTRL_MHL3_SCRAMBLER_EN          BIT(0)

/* HSIC Div Ctl, default value: 0x05 */
#define REG_DIV_CTL_MAIN                        0x03f2
#define MSK_DIV_CTL_MAIN_PRE_DIV_CTL_MAIN       0x1c
#define MSK_DIV_CTL_MAIN_FB_DIV_CTL_MAIN        0x03

/* MHL Capability 1st Byte, default value: 0x00 */
#define REG_MHL_DEVCAP_0                        0x0400

/* MHL Interrupt 1st Byte, default value: 0x00 */
#define REG_MHL_INT_0                           0x0420

/* Device Status 1st byte, default value: 0x00 */
#define REG_MHL_STAT_0                          0x0430

/* CBUS Scratch Pad 1st Byte, default value: 0x00 */
#define REG_MHL_SCRPAD_0                        0x0440

/* MHL Extended Capability 1st Byte, default value: 0x00 */
#define REG_MHL_EXTDEVCAP_0                     0x0480

/* Device Extended Status 1st byte, default value: 0x00 */
#define REG_MHL_EXTSTAT_0                       0x0490

/* TPI DTD Byte2, default value: 0x00 */
#define REG_TPI_DTD_B2                          0x0602

#define VAL_TPI_QUAN_RANGE_LIMITED              0x01
#define VAL_TPI_QUAN_RANGE_FULL                 0x02
#define VAL_TPI_FORMAT_RGB                      0x00
#define VAL_TPI_FORMAT_YCBCR444                 0x01
#define VAL_TPI_FORMAT_YCBCR422                 0x02
#define VAL_TPI_FORMAT_INTERNAL_RGB             0x03
#define VAL_TPI_FORMAT(_fmt, _qr) \
                (VAL_TPI_FORMAT_##_fmt | (VAL_TPI_QUAN_RANGE_##_qr << 2))

/* Input Format, default value: 0x00 */
#define REG_TPI_INPUT                           0x0609
#define BIT_TPI_INPUT_EXTENDEDBITMODE           BIT(7)
#define BIT_TPI_INPUT_ENDITHER                  BIT(6)
#define MSK_TPI_INPUT_INPUT_QUAN_RANGE          0x0c
#define MSK_TPI_INPUT_INPUT_FORMAT              0x03

/* Output Format, default value: 0x00 */
#define REG_TPI_OUTPUT                          0x060a
#define BIT_TPI_OUTPUT_CSCMODE709               BIT(4)
#define MSK_TPI_OUTPUT_OUTPUT_QUAN_RANGE        0x0c
#define MSK_TPI_OUTPUT_OUTPUT_FORMAT            0x03

/* TPI AVI Check Sum, default value: 0x00 */
#define REG_TPI_AVI_CHSUM                       0x060c

/* TPI System Control, default value: 0x00 */
#define REG_TPI_SC                              0x061a
#define BIT_TPI_SC_TPI_UPDATE_FLG               BIT(7)
#define BIT_TPI_SC_TPI_REAUTH_CTL               BIT(6)
#define BIT_TPI_SC_TPI_OUTPUT_MODE_1            BIT(5)
#define BIT_TPI_SC_REG_TMDS_OE_POWER_DOWN       BIT(4)
#define BIT_TPI_SC_TPI_AV_MUTE                  BIT(3)
#define BIT_TPI_SC_DDC_GPU_REQUEST              BIT(2)
#define BIT_TPI_SC_DDC_TPI_SW                   BIT(1)
#define BIT_TPI_SC_TPI_OUTPUT_MODE_0_HDMI       BIT(0)

/* TPI COPP Query Data, default value: 0x00 */
#define REG_TPI_COPP_DATA1                      0x0629
#define BIT_TPI_COPP_DATA1_COPP_GPROT           BIT(7)
#define BIT_TPI_COPP_DATA1_COPP_LPROT           BIT(6)
#define MSK_TPI_COPP_DATA1_COPP_LINK_STATUS     0x30
#define VAL_TPI_COPP_LINK_STATUS_NORMAL         0x00
#define VAL_TPI_COPP_LINK_STATUS_LINK_LOST      0x10
#define VAL_TPI_COPP_LINK_STATUS_RENEGOTIATION_REQ 0x20
#define VAL_TPI_COPP_LINK_STATUS_LINK_SUSPENDED 0x30
#define BIT_TPI_COPP_DATA1_COPP_HDCP_REP        BIT(3)
#define BIT_TPI_COPP_DATA1_COPP_CONNTYPE_0      BIT(2)
#define BIT_TPI_COPP_DATA1_COPP_PROTYPE         BIT(1)
#define BIT_TPI_COPP_DATA1_COPP_CONNTYPE_1      BIT(0)

/* TPI COPP Control Data, default value: 0x00 */
#define REG_TPI_COPP_DATA2                      0x062a
#define BIT_TPI_COPP_DATA2_INTR_ENCRYPTION      BIT(5)
#define BIT_TPI_COPP_DATA2_KSV_FORWARD          BIT(4)
#define BIT_TPI_COPP_DATA2_INTERM_RI_CHECK_EN   BIT(3)
#define BIT_TPI_COPP_DATA2_DOUBLE_RI_CHECK      BIT(2)
#define BIT_TPI_COPP_DATA2_DDC_SHORT_RI_RD      BIT(1)
#define BIT_TPI_COPP_DATA2_COPP_PROTLEVEL       BIT(0)

/* TPI Interrupt Enable, default value: 0x00 */
#define REG_TPI_INTR_EN                         0x063c

/* TPI Interrupt Status Low Byte, default value: 0x00 */
#define REG_TPI_INTR_ST0                        0x063d
#define BIT_TPI_INTR_ST0_TPI_AUTH_CHNGE_STAT    BIT(7)
#define BIT_TPI_INTR_ST0_TPI_V_RDY_STAT         BIT(6)
#define BIT_TPI_INTR_ST0_TPI_COPP_CHNGE_STAT    BIT(5)
#define BIT_TPI_INTR_ST0_KSV_FIFO_FIRST_STAT    BIT(3)
#define BIT_TPI_INTR_ST0_READ_BKSV_BCAPS_DONE_STAT BIT(2)
#define BIT_TPI_INTR_ST0_READ_BKSV_BCAPS_ERR_STAT BIT(1)
#define BIT_TPI_INTR_ST0_READ_BKSV_ERR_STAT     BIT(0)

/* TPI DS BCAPS Status, default value: 0x00 */
#define REG_TPI_DS_BCAPS                        0x0644

/* TPI BStatus1, default value: 0x00 */
#define REG_TPI_BSTATUS1                        0x0645
#define BIT_TPI_BSTATUS1_DS_DEV_EXCEED          BIT(7)
#define MSK_TPI_BSTATUS1_DS_DEV_CNT             0x7f

/* TPI BStatus2, default value: 0x10 */
#define REG_TPI_BSTATUS2                        0x0646
#define MSK_TPI_BSTATUS2_DS_BSTATUS             0xe0
#define BIT_TPI_BSTATUS2_DS_HDMI_MODE           BIT(4)
#define BIT_TPI_BSTATUS2_DS_CASC_EXCEED         BIT(3)
#define MSK_TPI_BSTATUS2_DS_DEPTH               0x07

/* TPI HW Optimization Control #3, default value: 0x00 */
#define REG_TPI_HW_OPT3                         0x06bb
#define BIT_TPI_HW_OPT3_DDC_DEBUG               BIT(7)
#define BIT_TPI_HW_OPT3_RI_CHECK_SKIP           BIT(3)
#define BIT_TPI_HW_OPT3_TPI_DDC_BURST_MODE      BIT(2)
#define MSK_TPI_HW_OPT3_TPI_DDC_REQ_LEVEL       0x03

/* TPI Info Frame Select, default value: 0x00 */
#define REG_TPI_INFO_FSEL                       0x06bf
#define BIT_TPI_INFO_FSEL_EN                    BIT(7)
#define BIT_TPI_INFO_FSEL_RPT                   BIT(6)
#define BIT_TPI_INFO_FSEL_READ_FLAG             BIT(5)
#define MSK_TPI_INFO_FSEL_PKT                   0x07
#define VAL_TPI_INFO_FSEL_AVI                   0x00
#define VAL_TPI_INFO_FSEL_SPD                   0x01
#define VAL_TPI_INFO_FSEL_AUD                   0x02
#define VAL_TPI_INFO_FSEL_MPG                   0x03
#define VAL_TPI_INFO_FSEL_GEN                   0x04
#define VAL_TPI_INFO_FSEL_GEN2                  0x05
#define VAL_TPI_INFO_FSEL_VSI                   0x06

/* TPI Info Byte #0, default value: 0x00 */
#define REG_TPI_INFO_B0                         0x06c0

/* CoC Status, default value: 0x00 */
#define REG_COC_STAT_0                          0x0700
#define BIT_COC_STAT_0_PLL_LOCKED               BIT(7)
#define MSK_COC_STAT_0_FSM_STATE                0x0f

#define REG_COC_STAT_1                          0x0701
#define REG_COC_STAT_2                          0x0702
#define REG_COC_STAT_3                          0x0703
#define REG_COC_STAT_4                          0x0704
#define REG_COC_STAT_5                          0x0705

/* CoC 1st Ctl, default value: 0x40 */
#define REG_COC_CTL0                            0x0710

/* CoC 2nd Ctl, default value: 0x0a */
#define REG_COC_CTL1                            0x0711
#define MSK_COC_CTL1_COC_CTRL1_7_6              0xc0
#define MSK_COC_CTL1_COC_CTRL1_5_0              0x3f

/* CoC 3rd Ctl, default value: 0x14 */
#define REG_COC_CTL2                            0x0712
#define MSK_COC_CTL2_COC_CTRL2_7_6              0xc0
#define MSK_COC_CTL2_COC_CTRL2_5_0              0x3f

/* CoC 4th Ctl, default value: 0x40 */
#define REG_COC_CTL3                            0x0713
#define BIT_COC_CTL3_COC_CTRL3_7                BIT(7)
#define MSK_COC_CTL3_COC_CTRL3_6_0              0x7f

/* CoC 7th Ctl, default value: 0x00 */
#define REG_COC_CTL6                            0x0716
#define BIT_COC_CTL6_COC_CTRL6_7                BIT(7)
#define BIT_COC_CTL6_COC_CTRL6_6                BIT(6)
#define MSK_COC_CTL6_COC_CTRL6_5_0              0x3f

/* CoC 8th Ctl, default value: 0x06 */
#define REG_COC_CTL7                            0x0717
#define BIT_COC_CTL7_COC_CTRL7_7                BIT(7)
#define BIT_COC_CTL7_COC_CTRL7_6                BIT(6)
#define BIT_COC_CTL7_COC_CTRL7_5                BIT(5)
#define MSK_COC_CTL7_COC_CTRL7_4_3              0x18
#define MSK_COC_CTL7_COC_CTRL7_2_0              0x07

/* CoC 10th Ctl, default value: 0x00 */
#define REG_COC_CTL9                            0x0719

/* CoC 11th Ctl, default value: 0x00 */
#define REG_COC_CTLA                            0x071a

/* CoC 12th Ctl, default value: 0x00 */
#define REG_COC_CTLB                            0x071b

/* CoC 13th Ctl, default value: 0x0f */
#define REG_COC_CTLC                            0x071c

/* CoC 14th Ctl, default value: 0x0a */
#define REG_COC_CTLD                            0x071d
#define BIT_COC_CTLD_COC_CTRLD_7                BIT(7)
#define MSK_COC_CTLD_COC_CTRLD_6_0              0x7f

/* CoC 15th Ctl, default value: 0x0a */
#define REG_COC_CTLE                            0x071e
#define BIT_COC_CTLE_COC_CTRLE_7                BIT(7)
#define MSK_COC_CTLE_COC_CTRLE_6_0              0x7f

/* CoC 16th Ctl, default value: 0x00 */
#define REG_COC_CTLF                            0x071f
#define MSK_COC_CTLF_COC_CTRLF_7_3              0xf8
#define MSK_COC_CTLF_COC_CTRLF_2_0              0x07

/* CoC 18th Ctl, default value: 0x32 */
#define REG_COC_CTL11                           0x0721
#define MSK_COC_CTL11_COC_CTRL11_7_4            0xf0
#define MSK_COC_CTL11_COC_CTRL11_3_0            0x0f

/* CoC 21st Ctl, default value: 0x00 */
#define REG_COC_CTL14                           0x0724
#define MSK_COC_CTL14_COC_CTRL14_7_4            0xf0
#define MSK_COC_CTL14_COC_CTRL14_3_0            0x0f

/* CoC 22nd Ctl, default value: 0x00 */
#define REG_COC_CTL15                           0x0725
#define BIT_COC_CTL15_COC_CTRL15_7              BIT(7)
#define MSK_COC_CTL15_COC_CTRL15_6_4            0x70
#define MSK_COC_CTL15_COC_CTRL15_3_0            0x0f

/* CoC Interrupt, default value: 0x00 */
#define REG_COC_INTR                            0x0726

/* CoC Interrupt Mask, default value: 0x00 */
#define REG_COC_INTR_MASK                       0x0727
#define BIT_COC_PLL_LOCK_STATUS_CHANGE          BIT(0)
#define BIT_COC_CALIBRATION_DONE                BIT(1)

/* CoC Misc Ctl, default value: 0x00 */
#define REG_COC_MISC_CTL0                       0x0728
#define BIT_COC_MISC_CTL0_FSM_MON               BIT(7)

/* CoC 24th Ctl, default value: 0x00 */
#define REG_COC_CTL17                           0x072a
#define MSK_COC_CTL17_COC_CTRL17_7_4            0xf0
#define MSK_COC_CTL17_COC_CTRL17_3_0            0x0f

/* CoC 25th Ctl, default value: 0x00 */
#define REG_COC_CTL18                           0x072b
#define MSK_COC_CTL18_COC_CTRL18_7_4            0xf0
#define MSK_COC_CTL18_COC_CTRL18_3_0            0x0f

/* CoC 26th Ctl, default value: 0x00 */
#define REG_COC_CTL19                           0x072c
#define MSK_COC_CTL19_COC_CTRL19_7_4            0xf0
#define MSK_COC_CTL19_COC_CTRL19_3_0            0x0f

/* CoC 27th Ctl, default value: 0x00 */
#define REG_COC_CTL1A                           0x072d
#define MSK_COC_CTL1A_COC_CTRL1A_7_2            0xfc
#define MSK_COC_CTL1A_COC_CTRL1A_1_0            0x03

/* DoC 9th Status, default value: 0x00 */
#define REG_DOC_STAT_8                          0x0740

/* DoC 10th Status, default value: 0x00 */
#define REG_DOC_STAT_9                          0x0741

/* DoC 5th CFG, default value: 0x00 */
#define REG_DOC_CFG4                            0x074e
#define MSK_DOC_CFG4_DBG_STATE_DOC_FSM          0x0f

/* DoC 1st Ctl, default value: 0x40 */
#define REG_DOC_CTL0                            0x0751

/* DoC 7th Ctl, default value: 0x00 */
#define REG_DOC_CTL6                            0x0757
#define BIT_DOC_CTL6_DOC_CTRL6_7                BIT(7)
#define BIT_DOC_CTL6_DOC_CTRL6_6                BIT(6)
#define MSK_DOC_CTL6_DOC_CTRL6_5_4              0x30
#define MSK_DOC_CTL6_DOC_CTRL6_3_0              0x0f

/* DoC 8th Ctl, default value: 0x00 */
#define REG_DOC_CTL7                            0x0758
#define BIT_DOC_CTL7_DOC_CTRL7_7                BIT(7)
#define BIT_DOC_CTL7_DOC_CTRL7_6                BIT(6)
#define BIT_DOC_CTL7_DOC_CTRL7_5                BIT(5)
#define MSK_DOC_CTL7_DOC_CTRL7_4_3              0x18
#define MSK_DOC_CTL7_DOC_CTRL7_2_0              0x07

/* DoC 9th Ctl, default value: 0x00 */
#define REG_DOC_CTL8                            0x076c
#define BIT_DOC_CTL8_DOC_CTRL8_7                BIT(7)
#define MSK_DOC_CTL8_DOC_CTRL8_6_4              0x70
#define MSK_DOC_CTL8_DOC_CTRL8_3_2              0x0c
#define MSK_DOC_CTL8_DOC_CTRL8_1_0              0x03

/* DoC 10th Ctl, default value: 0x00 */
#define REG_DOC_CTL9                            0x076d

/* DoC 11th Ctl, default value: 0x00 */
#define REG_DOC_CTLA                            0x076e

/* DoC 15th Ctl, default value: 0x00 */
#define REG_DOC_CTLE                            0x0772
#define BIT_DOC_CTLE_DOC_CTRLE_7                BIT(7)
#define BIT_DOC_CTLE_DOC_CTRLE_6                BIT(6)
#define MSK_DOC_CTLE_DOC_CTRLE_5_4              0x30
#define MSK_DOC_CTLE_DOC_CTRLE_3_0              0x0f

/* Interrupt Mask 1st, default value: 0x00 */
#define REG_MHL_INT_0_MASK                      0x0580

/* Interrupt Mask 2nd, default value: 0x00 */
#define REG_MHL_INT_1_MASK                      0x0581

/* Interrupt Mask 3rd, default value: 0x00 */
#define REG_MHL_INT_2_MASK                      0x0582

/* Interrupt Mask 4th, default value: 0x00 */
#define REG_MHL_INT_3_MASK                      0x0583

/* MDT Receive Time Out, default value: 0x00 */
#define REG_MDT_RCV_TIMEOUT                     0x0584

/* MDT Transmit Time Out, default value: 0x00 */
#define REG_MDT_XMIT_TIMEOUT                    0x0585

/* MDT Receive Control, default value: 0x00 */
#define REG_MDT_RCV_CTRL                        0x0586
#define BIT_MDT_RCV_CTRL_MDT_RCV_EN             BIT(7)
#define BIT_MDT_RCV_CTRL_MDT_DELAY_RCV_EN       BIT(6)
#define BIT_MDT_RCV_CTRL_MDT_RFIFO_OVER_WR_EN   BIT(4)
#define BIT_MDT_RCV_CTRL_MDT_XFIFO_OVER_WR_EN   BIT(3)
#define BIT_MDT_RCV_CTRL_MDT_DISABLE            BIT(2)
#define BIT_MDT_RCV_CTRL_MDT_RFIFO_CLR_ALL      BIT(1)
#define BIT_MDT_RCV_CTRL_MDT_RFIFO_CLR_CUR      BIT(0)

/* MDT Receive Read Port, default value: 0x00 */
#define REG_MDT_RCV_READ_PORT                   0x0587

/* MDT Transmit Control, default value: 0x70 */
#define REG_MDT_XMIT_CTRL                       0x0588
#define BIT_MDT_XMIT_CTRL_EN                    BIT(7)
#define BIT_MDT_XMIT_CTRL_CMD_MERGE_EN          BIT(6)
#define BIT_MDT_XMIT_CTRL_FIXED_BURST_LEN       BIT(5)
#define BIT_MDT_XMIT_CTRL_FIXED_AID             BIT(4)
#define BIT_MDT_XMIT_CTRL_SINGLE_RUN_EN         BIT(3)
#define BIT_MDT_XMIT_CTRL_CLR_ABORT_WAIT        BIT(2)
#define BIT_MDT_XMIT_CTRL_XFIFO_CLR_ALL         BIT(1)
#define BIT_MDT_XMIT_CTRL_XFIFO_CLR_CUR         BIT(0)

/* MDT Receive WRITE Port, default value: 0x00 */
#define REG_MDT_XMIT_WRITE_PORT                 0x0589

/* MDT RFIFO Status, default value: 0x00 */
#define REG_MDT_RFIFO_STAT                      0x058a
#define MSK_MDT_RFIFO_STAT_MDT_RFIFO_CNT        0xe0
#define MSK_MDT_RFIFO_STAT_MDT_RFIFO_CUR_BYTE_CNT 0x1f

/* MDT XFIFO Status, default value: 0x80 */
#define REG_MDT_XFIFO_STAT                      0x058b
#define MSK_MDT_XFIFO_STAT_MDT_XFIFO_LEVEL_AVAIL 0xe0
#define BIT_MDT_XFIFO_STAT_MDT_XMIT_PRE_HS_EN   BIT(4)
#define MSK_MDT_XFIFO_STAT_MDT_WRITE_BURST_LEN  0x0f

/* MDT Interrupt 0, default value: 0x0c */
#define REG_MDT_INT_0                           0x058c
#define BIT_MDT_RFIFO_DATA_RDY                  BIT(0)
#define BIT_MDT_IDLE_AFTER_HAWB_DISABLE         BIT(2)
#define BIT_MDT_XFIFO_EMPTY                     BIT(3)

/* MDT Interrupt 0 Mask, default value: 0x00 */
#define REG_MDT_INT_0_MASK                      0x058d

/* MDT Interrupt 1, default value: 0x00 */
#define REG_MDT_INT_1                           0x058e
#define BIT_MDT_RCV_TIMEOUT                     BIT(0)
#define BIT_MDT_RCV_SM_ABORT_PKT_RCVD           BIT(1)
#define BIT_MDT_RCV_SM_ERROR                    BIT(2)
#define BIT_MDT_XMIT_TIMEOUT                    BIT(5)
#define BIT_MDT_XMIT_SM_ABORT_PKT_RCVD          BIT(6)
#define BIT_MDT_XMIT_SM_ERROR                   BIT(7)

/* MDT Interrupt 1 Mask, default value: 0x00 */
#define REG_MDT_INT_1_MASK                      0x058f

/* CBUS Vendor ID, default value: 0x01 */
#define REG_CBUS_VENDOR_ID                      0x0590

/* CBUS Connection Status, default value: 0x00 */
#define REG_CBUS_STATUS                         0x0591
#define BIT_CBUS_STATUS_MHL_CABLE_PRESENT       BIT(4)
#define BIT_CBUS_STATUS_MSC_HB_SUCCESS          BIT(3)
#define BIT_CBUS_STATUS_CBUS_HPD                BIT(2)
#define BIT_CBUS_STATUS_MHL_MODE                BIT(1)
#define BIT_CBUS_STATUS_CBUS_CONNECTED          BIT(0)

/* CBUS Interrupt 1st, default value: 0x00 */
#define REG_CBUS_INT_0                          0x0592
#define BIT_CBUS_MSC_MT_DONE_NACK               BIT(7)
#define BIT_CBUS_MSC_MR_SET_INT                 BIT(6)
#define BIT_CBUS_MSC_MR_WRITE_BURST             BIT(5)
#define BIT_CBUS_MSC_MR_MSC_MSG                 BIT(4)
#define BIT_CBUS_MSC_MR_WRITE_STAT              BIT(3)
#define BIT_CBUS_HPD_CHG                        BIT(2)
#define BIT_CBUS_MSC_MT_DONE                    BIT(1)
#define BIT_CBUS_CNX_CHG                        BIT(0)

/* CBUS Interrupt Mask 1st, default value: 0x00 */
#define REG_CBUS_INT_0_MASK                     0x0593

/* CBUS Interrupt 2nd, default value: 0x00 */
#define REG_CBUS_INT_1                          0x0594
#define BIT_CBUS_CMD_ABORT                      BIT(6)
#define BIT_CBUS_MSC_ABORT_RCVD                 BIT(3)
#define BIT_CBUS_DDC_ABORT                      BIT(2)
#define BIT_CBUS_CEC_ABORT                      BIT(1)

/* CBUS Interrupt Mask 2nd, default value: 0x00 */
#define REG_CBUS_INT_1_MASK                     0x0595

/* CBUS DDC Abort Interrupt, default value: 0x00 */
#define REG_DDC_ABORT_INT                       0x0598

/* CBUS DDC Abort Interrupt Mask, default value: 0x00 */
#define REG_DDC_ABORT_INT_MASK                  0x0599

/* CBUS MSC Requester Abort Interrupt, default value: 0x00 */
#define REG_MSC_MT_ABORT_INT                    0x059a

/* CBUS MSC Requester Abort Interrupt Mask, default value: 0x00 */
#define REG_MSC_MT_ABORT_INT_MASK               0x059b

/* CBUS MSC Responder Abort Interrupt, default value: 0x00 */
#define REG_MSC_MR_ABORT_INT                    0x059c

/* CBUS MSC Responder Abort Interrupt Mask, default value: 0x00 */
#define REG_MSC_MR_ABORT_INT_MASK               0x059d

/* CBUS RX DISCOVERY interrupt, default value: 0x00 */
#define REG_CBUS_RX_DISC_INT0                   0x059e

/* CBUS RX DISCOVERY Interrupt Mask, default value: 0x00 */
#define REG_CBUS_RX_DISC_INT0_MASK              0x059f

/* CBUS_Link_Layer Control #8, default value: 0x00 */
#define REG_CBUS_LINK_CTRL_8                    0x05a7

/* MDT State Machine Status, default value: 0x00 */
#define REG_MDT_SM_STAT                         0x05b5
#define MSK_MDT_SM_STAT_MDT_RCV_STATE           0xf0
#define MSK_MDT_SM_STAT_MDT_XMIT_STATE          0x0f

/* CBUS MSC command trigger, default value: 0x00 */
#define REG_MSC_COMMAND_START                   0x05b8
#define BIT_MSC_COMMAND_START_DEBUG             BIT(5)
#define BIT_MSC_COMMAND_START_WRITE_BURST       BIT(4)
#define BIT_MSC_COMMAND_START_WRITE_STAT        BIT(3)
#define BIT_MSC_COMMAND_START_READ_DEVCAP       BIT(2)
#define BIT_MSC_COMMAND_START_MSC_MSG           BIT(1)
#define BIT_MSC_COMMAND_START_PEER              BIT(0)

/* CBUS MSC Command/Offset, default value: 0x00 */
#define REG_MSC_CMD_OR_OFFSET                   0x05b9

/* CBUS MSC Transmit Data */
#define REG_MSC_1ST_TRANSMIT_DATA               0x05ba
#define REG_MSC_2ND_TRANSMIT_DATA               0x05bb

/* CBUS MSC Requester Received Data */
#define REG_MSC_MT_RCVD_DATA0                   0x05bc
#define REG_MSC_MT_RCVD_DATA1                   0x05bd

/* CBUS MSC Responder MSC_MSG Received Data */
#define REG_MSC_MR_MSC_MSG_RCVD_1ST_DATA        0x05bf
#define REG_MSC_MR_MSC_MSG_RCVD_2ND_DATA        0x05c0

/* CBUS MSC Heartbeat Control, default value: 0x27 */
#define REG_MSC_HEARTBEAT_CTRL                  0x05c4
#define BIT_MSC_HEARTBEAT_CTRL_MSC_HB_EN        BIT(7)
#define MSK_MSC_HEARTBEAT_CTRL_MSC_HB_FAIL_LIMIT 0x70
#define MSK_MSC_HEARTBEAT_CTRL_MSC_HB_PERIOD_MSB 0x0f

/* CBUS MSC Compatibility Control, default value: 0x02 */
#define REG_CBUS_MSC_COMPAT_CTRL                0x05c7
#define BIT_CBUS_MSC_COMPAT_CTRL_XDEVCAP_EN     BIT(7)
#define BIT_CBUS_MSC_COMPAT_CTRL_DISABLE_MSC_ON_CBUS BIT(6)
#define BIT_CBUS_MSC_COMPAT_CTRL_DISABLE_DDC_ON_CBUS BIT(5)
#define BIT_CBUS_MSC_COMPAT_CTRL_DISABLE_GET_DDC_ERRORCODE BIT(3)
#define BIT_CBUS_MSC_COMPAT_CTRL_DISABLE_GET_VS1_ERRORCODE BIT(2)

/* CBUS3 Converter Control, default value: 0x24 */
#define REG_CBUS3_CNVT                          0x05dc
#define MSK_CBUS3_CNVT_CBUS3_RETRYLMT           0xf0
#define MSK_CBUS3_CNVT_CBUS3_PEERTOUT_SEL       0x0c
#define BIT_CBUS3_CNVT_TEARCBUS_EN              BIT(1)
#define BIT_CBUS3_CNVT_CBUS3CNVT_EN             BIT(0)

/* Discovery Control1, default value: 0x24 */
#define REG_DISC_CTRL1                          0x05e0
#define BIT_DISC_CTRL1_CBUS_INTR_EN             BIT(7)
#define BIT_DISC_CTRL1_HB_ONLY                  BIT(6)
#define MSK_DISC_CTRL1_DISC_ATT                 0x30
#define MSK_DISC_CTRL1_DISC_CYC                 0x0c
#define BIT_DISC_CTRL1_DISC_EN                  BIT(0)

#define VAL_PUP_OFF                             0
#define VAL_PUP_20K                             1
#define VAL_PUP_5K                              2

/* Discovery Control4, default value: 0x80 */
#define REG_DISC_CTRL4                          0x05e3
#define MSK_DISC_CTRL4_CBUSDISC_PUP_SEL         0xc0
#define MSK_DISC_CTRL4_CBUSIDLE_PUP_SEL         0x30
#define VAL_DISC_CTRL4(pup_disc, pup_idle) (((pup_disc) << 6) | (pup_idle << 4))

/* Discovery Control5, default value: 0x03 */
#define REG_DISC_CTRL5                          0x05e4
#define BIT_DISC_CTRL5_DSM_OVRIDE               BIT(3)
#define MSK_DISC_CTRL5_CBUSMHL_PUP_SEL          0x03

/* Discovery Control8, default value: 0x81 */
#define REG_DISC_CTRL8                          0x05e7
#define BIT_DISC_CTRL8_NOMHLINT_CLR_BYPASS      BIT(7)
#define BIT_DISC_CTRL8_DELAY_CBUS_INTR_EN       BIT(0)

/* Discovery Control9, default value: 0x54 */
#define REG_DISC_CTRL9                  0x05e8
#define BIT_DISC_CTRL9_MHL3_RSEN_BYP            BIT(7)
#define BIT_DISC_CTRL9_MHL3DISC_EN              BIT(6)
#define BIT_DISC_CTRL9_WAKE_DRVFLT              BIT(4)
#define BIT_DISC_CTRL9_NOMHL_EST                BIT(3)
#define BIT_DISC_CTRL9_DISC_PULSE_PROCEED       BIT(2)
#define BIT_DISC_CTRL9_WAKE_PULSE_BYPASS        BIT(1)
#define BIT_DISC_CTRL9_VBUS_OUTPUT_CAPABILITY_SRC BIT(0)

/* Discovery Status1, default value: 0x00 */
#define REG_DISC_STAT1                          0x05eb
#define BIT_DISC_STAT1_PSM_OVRIDE               BIT(5)
#define MSK_DISC_STAT1_DISC_SM                  0x0f

/* Discovery Status2, default value: 0x00 */
#define REG_DISC_STAT2                          0x05ec
#define BIT_DISC_STAT2_CBUS_OE_POL              BIT(6)
#define BIT_DISC_STAT2_CBUS_SATUS               BIT(5)
#define BIT_DISC_STAT2_RSEN                     BIT(4)

#define MSK_DISC_STAT2_MHL_VRSN                 0x0c
#define VAL_DISC_STAT2_DEFAULT                  0x00
#define VAL_DISC_STAT2_MHL1_2                   0x04
#define VAL_DISC_STAT2_MHL3                     0x08
#define VAL_DISC_STAT2_RESERVED                 0x0c

#define MSK_DISC_STAT2_RGND                     0x03
#define VAL_RGND_OPEN                           0x00
#define VAL_RGND_2K                             0x01
#define VAL_RGND_1K                             0x02
#define VAL_RGND_SHORT                          0x03

/* Interrupt CBUS_reg1 INTR0, default value: 0x00 */
#define REG_CBUS_DISC_INTR0                     0x05ed
#define BIT_RGND_READY_INT                      BIT(6)
#define BIT_CBUS_MHL12_DISCON_INT               BIT(5)
#define BIT_CBUS_MHL3_DISCON_INT                BIT(4)
#define BIT_NOT_MHL_EST_INT                     BIT(3)
#define BIT_MHL_EST_INT                         BIT(2)
#define BIT_MHL3_EST_INT                        BIT(1)
#define VAL_CBUS_MHL_DISCON (BIT_CBUS_MHL12_DISCON_INT \
                            | BIT_CBUS_MHL3_DISCON_INT \
                            | BIT_NOT_MHL_EST_INT)

/* Interrupt CBUS_reg1 INTR0 Mask, default value: 0x00 */
#define REG_CBUS_DISC_INTR0_MASK                0x05ee

#endif /* __SIL_SII8620_H__ */