dt-bindings: mtd: ingenic: Use standard ecc-engine property

[linux/fpc-iii.git] / drivers / thermal / mtk_thermal.c

/*
 * Copyright (c) 2015 MediaTek Inc.
 * Author: Hanyi Wu <hanyi.wu@mediatek.com>
 *         Sascha Hauer <s.hauer@pengutronix.de>
 *         Dawei Chien <dawei.chien@mediatek.com>
 *         Louis Yu <louis.yu@mediatek.com>
 *
 * This program is free software; you can redistribute it and/or modify
 * it under the terms of the GNU General Public License version 2 as
 * published by the Free Software Foundation.
 *
 * This program is distributed in the hope that it will be useful,
 * but WITHOUT ANY WARRANTY; without even the implied warranty of
 * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
 * GNU General Public License for more details.
 */

#include <linux/clk.h>
#include <linux/delay.h>
#include <linux/interrupt.h>
#include <linux/kernel.h>
#include <linux/module.h>
#include <linux/nvmem-consumer.h>
#include <linux/of.h>
#include <linux/of_address.h>
#include <linux/of_device.h>
#include <linux/platform_device.h>
#include <linux/slab.h>
#include <linux/io.h>
#include <linux/thermal.h>
#include <linux/reset.h>
#include <linux/types.h>

/* AUXADC Registers */
#define AUXADC_CON1_SET_V       0x008
#define AUXADC_CON1_CLR_V       0x00c
#define AUXADC_CON2_V           0x010
#define AUXADC_DATA(channel)    (0x14 + (channel) * 4)

#define APMIXED_SYS_TS_CON1     0x604

/* Thermal Controller Registers */
#define TEMP_MONCTL0            0x000
#define TEMP_MONCTL1            0x004
#define TEMP_MONCTL2            0x008
#define TEMP_MONIDET0           0x014
#define TEMP_MONIDET1           0x018
#define TEMP_MSRCTL0            0x038
#define TEMP_AHBPOLL            0x040
#define TEMP_AHBTO              0x044
#define TEMP_ADCPNP0            0x048
#define TEMP_ADCPNP1            0x04c
#define TEMP_ADCPNP2            0x050
#define TEMP_ADCPNP3            0x0b4

#define TEMP_ADCMUX             0x054
#define TEMP_ADCEN              0x060
#define TEMP_PNPMUXADDR         0x064
#define TEMP_ADCMUXADDR         0x068
#define TEMP_ADCENADDR          0x074
#define TEMP_ADCVALIDADDR       0x078
#define TEMP_ADCVOLTADDR        0x07c
#define TEMP_RDCTRL             0x080
#define TEMP_ADCVALIDMASK       0x084
#define TEMP_ADCVOLTAGESHIFT    0x088
#define TEMP_ADCWRITECTRL       0x08c
#define TEMP_MSR0               0x090
#define TEMP_MSR1               0x094
#define TEMP_MSR2               0x098
#define TEMP_MSR3               0x0B8

#define TEMP_SPARE0             0x0f0

#define TEMP_ADCPNP0_1          0x148
#define TEMP_ADCPNP1_1          0x14c
#define TEMP_ADCPNP2_1          0x150
#define TEMP_MSR0_1             0x190
#define TEMP_MSR1_1             0x194
#define TEMP_MSR2_1             0x198
#define TEMP_ADCPNP3_1          0x1b4
#define TEMP_MSR3_1             0x1B8

#define PTPCORESEL              0x400

#define TEMP_MONCTL1_PERIOD_UNIT(x)     ((x) & 0x3ff)

#define TEMP_MONCTL2_FILTER_INTERVAL(x) (((x) & 0x3ff) << 16)
#define TEMP_MONCTL2_SENSOR_INTERVAL(x) ((x) & 0x3ff)

#define TEMP_AHBPOLL_ADC_POLL_INTERVAL(x)       (x)

#define TEMP_ADCWRITECTRL_ADC_PNP_WRITE         BIT(0)
#define TEMP_ADCWRITECTRL_ADC_MUX_WRITE         BIT(1)

#define TEMP_ADCVALIDMASK_VALID_HIGH            BIT(5)
#define TEMP_ADCVALIDMASK_VALID_POS(bit)        (bit)

/* MT8173 thermal sensors */
#define MT8173_TS1      0
#define MT8173_TS2      1
#define MT8173_TS3      2
#define MT8173_TS4      3
#define MT8173_TSABB    4

/* AUXADC channel 11 is used for the temperature sensors */
#define MT8173_TEMP_AUXADC_CHANNEL      11

/* The total number of temperature sensors in the MT8173 */
#define MT8173_NUM_SENSORS              5

/* The number of banks in the MT8173 */
#define MT8173_NUM_ZONES                4

/* The number of sensing points per bank */
#define MT8173_NUM_SENSORS_PER_ZONE     4

/* The number of controller in the MT8173 */
#define MT8173_NUM_CONTROLLER           1

/* The calibration coefficient of sensor  */
#define MT8173_CALIBRATION      165

/*
 * Layout of the fuses providing the calibration data
 * These macros could be used for MT8183, MT8173, MT2701, and MT2712.
 * MT8183 has 6 sensors and needs 6 VTS calibration data.
 * MT8173 has 5 sensors and needs 5 VTS calibration data.
 * MT2701 has 3 sensors and needs 3 VTS calibration data.
 * MT2712 has 4 sensors and needs 4 VTS calibration data.
 */
#define CALIB_BUF0_VALID                BIT(0)
#define CALIB_BUF1_ADC_GE(x)            (((x) >> 22) & 0x3ff)
#define CALIB_BUF0_VTS_TS1(x)           (((x) >> 17) & 0x1ff)
#define CALIB_BUF0_VTS_TS2(x)           (((x) >> 8) & 0x1ff)
#define CALIB_BUF1_VTS_TS3(x)           (((x) >> 0) & 0x1ff)
#define CALIB_BUF2_VTS_TS4(x)           (((x) >> 23) & 0x1ff)
#define CALIB_BUF2_VTS_TS5(x)           (((x) >> 5) & 0x1ff)
#define CALIB_BUF2_VTS_TSABB(x)         (((x) >> 14) & 0x1ff)
#define CALIB_BUF0_DEGC_CALI(x)         (((x) >> 1) & 0x3f)
#define CALIB_BUF0_O_SLOPE(x)           (((x) >> 26) & 0x3f)
#define CALIB_BUF0_O_SLOPE_SIGN(x)      (((x) >> 7) & 0x1)
#define CALIB_BUF1_ID(x)                (((x) >> 9) & 0x1)

enum {
        VTS1,
        VTS2,
        VTS3,
        VTS4,
        VTS5,
        VTSABB,
        MAX_NUM_VTS,
};

/* MT2701 thermal sensors */
#define MT2701_TS1      0
#define MT2701_TS2      1
#define MT2701_TSABB    2

/* AUXADC channel 11 is used for the temperature sensors */
#define MT2701_TEMP_AUXADC_CHANNEL      11

/* The total number of temperature sensors in the MT2701 */
#define MT2701_NUM_SENSORS      3

/* The number of sensing points per bank */
#define MT2701_NUM_SENSORS_PER_ZONE     3

/* The number of controller in the MT2701 */
#define MT2701_NUM_CONTROLLER           1

/* The calibration coefficient of sensor  */
#define MT2701_CALIBRATION      165

/* MT2712 thermal sensors */
#define MT2712_TS1      0
#define MT2712_TS2      1
#define MT2712_TS3      2
#define MT2712_TS4      3

/* AUXADC channel 11 is used for the temperature sensors */
#define MT2712_TEMP_AUXADC_CHANNEL      11

/* The total number of temperature sensors in the MT2712 */
#define MT2712_NUM_SENSORS      4

/* The number of sensing points per bank */
#define MT2712_NUM_SENSORS_PER_ZONE     4

/* The number of controller in the MT2712 */
#define MT2712_NUM_CONTROLLER           1

/* The calibration coefficient of sensor  */
#define MT2712_CALIBRATION      165

#define MT7622_TEMP_AUXADC_CHANNEL      11
#define MT7622_NUM_SENSORS              1
#define MT7622_NUM_ZONES                1
#define MT7622_NUM_SENSORS_PER_ZONE     1
#define MT7622_TS1      0
#define MT7622_NUM_CONTROLLER           1

/* The calibration coefficient of sensor  */
#define MT7622_CALIBRATION      165

/* MT8183 thermal sensors */
#define MT8183_TS1      0
#define MT8183_TS2      1
#define MT8183_TS3      2
#define MT8183_TS4      3
#define MT8183_TS5      4
#define MT8183_TSABB    5

/* AUXADC channel  is used for the temperature sensors */
#define MT8183_TEMP_AUXADC_CHANNEL      11

/* The total number of temperature sensors in the MT8183 */
#define MT8183_NUM_SENSORS      6

/* The number of sensing points per bank */
#define MT8183_NUM_SENSORS_PER_ZONE      6

/* The number of controller in the MT8183 */
#define MT8183_NUM_CONTROLLER           2

/* The calibration coefficient of sensor  */
#define MT8183_CALIBRATION      153

struct mtk_thermal;

struct thermal_bank_cfg {
        unsigned int num_sensors;
        const int *sensors;
};

struct mtk_thermal_bank {
        struct mtk_thermal *mt;
        int id;
};

struct mtk_thermal_data {
        s32 num_banks;
        s32 num_sensors;
        s32 auxadc_channel;
        const int *vts_index;
        const int *sensor_mux_values;
        const int *msr;
        const int *adcpnp;
        const int cali_val;
        const int num_controller;
        const int *controller_offset;
        bool need_switch_bank;
        struct thermal_bank_cfg bank_data[];
};

struct mtk_thermal {
        struct device *dev;
        void __iomem *thermal_base;

        struct clk *clk_peri_therm;
        struct clk *clk_auxadc;
        /* lock: for getting and putting banks */
        struct mutex lock;

        /* Calibration values */
        s32 adc_ge;
        s32 degc_cali;
        s32 o_slope;
        s32 vts[MAX_NUM_VTS];

        const struct mtk_thermal_data *conf;
        struct mtk_thermal_bank banks[];
};

/* MT8183 thermal sensor data */
static const int mt8183_bank_data[MT8183_NUM_SENSORS] = {
        MT8183_TS1, MT8183_TS2, MT8183_TS3, MT8183_TS4, MT8183_TS5, MT8183_TSABB
};

static const int mt8183_msr[MT8183_NUM_SENSORS_PER_ZONE] = {
        TEMP_MSR0_1, TEMP_MSR1_1, TEMP_MSR2_1, TEMP_MSR1, TEMP_MSR0, TEMP_MSR3_1
};

static const int mt8183_adcpnp[MT8183_NUM_SENSORS_PER_ZONE] = {
        TEMP_ADCPNP0_1, TEMP_ADCPNP1_1, TEMP_ADCPNP2_1,
        TEMP_ADCPNP1, TEMP_ADCPNP0, TEMP_ADCPNP3_1
};

static const int mt8183_mux_values[MT8183_NUM_SENSORS] = { 0, 1, 2, 3, 4, 0 };
static const int mt8183_tc_offset[MT8183_NUM_CONTROLLER] = {0x0, 0x100};

static const int mt8183_vts_index[MT8183_NUM_SENSORS] = {
        VTS1, VTS2, VTS3, VTS4, VTS5, VTSABB
};

/* MT8173 thermal sensor data */
static const int mt8173_bank_data[MT8173_NUM_ZONES][3] = {
        { MT8173_TS2, MT8173_TS3 },
        { MT8173_TS2, MT8173_TS4 },
        { MT8173_TS1, MT8173_TS2, MT8173_TSABB },
        { MT8173_TS2 },
};

static const int mt8173_msr[MT8173_NUM_SENSORS_PER_ZONE] = {
        TEMP_MSR0, TEMP_MSR1, TEMP_MSR2, TEMP_MSR3
};

static const int mt8173_adcpnp[MT8173_NUM_SENSORS_PER_ZONE] = {
        TEMP_ADCPNP0, TEMP_ADCPNP1, TEMP_ADCPNP2, TEMP_ADCPNP3
};

static const int mt8173_mux_values[MT8173_NUM_SENSORS] = { 0, 1, 2, 3, 16 };
static const int mt8173_tc_offset[MT8173_NUM_CONTROLLER] = { 0x0, };

static const int mt8173_vts_index[MT8173_NUM_SENSORS] = {
        VTS1, VTS2, VTS3, VTS4, VTSABB
};

/* MT2701 thermal sensor data */
static const int mt2701_bank_data[MT2701_NUM_SENSORS] = {
        MT2701_TS1, MT2701_TS2, MT2701_TSABB
};

static const int mt2701_msr[MT2701_NUM_SENSORS_PER_ZONE] = {
        TEMP_MSR0, TEMP_MSR1, TEMP_MSR2
};

static const int mt2701_adcpnp[MT2701_NUM_SENSORS_PER_ZONE] = {
        TEMP_ADCPNP0, TEMP_ADCPNP1, TEMP_ADCPNP2
};

static const int mt2701_mux_values[MT2701_NUM_SENSORS] = { 0, 1, 16 };
static const int mt2701_tc_offset[MT2701_NUM_CONTROLLER] = { 0x0, };

static const int mt2701_vts_index[MT2701_NUM_SENSORS] = {
        VTS1, VTS2, VTS3
};

/* MT2712 thermal sensor data */
static const int mt2712_bank_data[MT2712_NUM_SENSORS] = {
        MT2712_TS1, MT2712_TS2, MT2712_TS3, MT2712_TS4
};

static const int mt2712_msr[MT2712_NUM_SENSORS_PER_ZONE] = {
        TEMP_MSR0, TEMP_MSR1, TEMP_MSR2, TEMP_MSR3
};

static const int mt2712_adcpnp[MT2712_NUM_SENSORS_PER_ZONE] = {
        TEMP_ADCPNP0, TEMP_ADCPNP1, TEMP_ADCPNP2, TEMP_ADCPNP3
};

static const int mt2712_mux_values[MT2712_NUM_SENSORS] = { 0, 1, 2, 3 };
static const int mt2712_tc_offset[MT2712_NUM_CONTROLLER] = { 0x0, };

static const int mt2712_vts_index[MT2712_NUM_SENSORS] = {
        VTS1, VTS2, VTS3, VTS4
};

/* MT7622 thermal sensor data */
static const int mt7622_bank_data[MT7622_NUM_SENSORS] = { MT7622_TS1, };
static const int mt7622_msr[MT7622_NUM_SENSORS_PER_ZONE] = { TEMP_MSR0, };
static const int mt7622_adcpnp[MT7622_NUM_SENSORS_PER_ZONE] = { TEMP_ADCPNP0, };
static const int mt7622_mux_values[MT7622_NUM_SENSORS] = { 0, };
static const int mt7622_vts_index[MT7622_NUM_SENSORS] = { VTS1 };
static const int mt7622_tc_offset[MT7622_NUM_CONTROLLER] = { 0x0, };

/**
 * The MT8173 thermal controller has four banks. Each bank can read up to
 * four temperature sensors simultaneously. The MT8173 has a total of 5
 * temperature sensors. We use each bank to measure a certain area of the
 * SoC. Since TS2 is located centrally in the SoC it is influenced by multiple
 * areas, hence is used in different banks.
 *
 * The thermal core only gets the maximum temperature of all banks, so
 * the bank concept wouldn't be necessary here. However, the SVS (Smart
 * Voltage Scaling) unit makes its decisions based on the same bank
 * data, and this indeed needs the temperatures of the individual banks
 * for making better decisions.
 */
static const struct mtk_thermal_data mt8173_thermal_data = {
        .auxadc_channel = MT8173_TEMP_AUXADC_CHANNEL,
        .num_banks = MT8173_NUM_ZONES,
        .num_sensors = MT8173_NUM_SENSORS,
        .vts_index = mt8173_vts_index,
        .cali_val = MT8173_CALIBRATION,
        .num_controller = MT8173_NUM_CONTROLLER,
        .controller_offset = mt8173_tc_offset,
        .need_switch_bank = true,
        .bank_data = {
                {
                        .num_sensors = 2,
                        .sensors = mt8173_bank_data[0],
                }, {
                        .num_sensors = 2,
                        .sensors = mt8173_bank_data[1],
                }, {
                        .num_sensors = 3,
                        .sensors = mt8173_bank_data[2],
                }, {
                        .num_sensors = 1,
                        .sensors = mt8173_bank_data[3],
                },
        },
        .msr = mt8173_msr,
        .adcpnp = mt8173_adcpnp,
        .sensor_mux_values = mt8173_mux_values,
};

/**
 * The MT2701 thermal controller has one bank, which can read up to
 * three temperature sensors simultaneously. The MT2701 has a total of 3
 * temperature sensors.
 *
 * The thermal core only gets the maximum temperature of this one bank,
 * so the bank concept wouldn't be necessary here. However, the SVS (Smart
 * Voltage Scaling) unit makes its decisions based on the same bank
 * data.
 */
static const struct mtk_thermal_data mt2701_thermal_data = {
        .auxadc_channel = MT2701_TEMP_AUXADC_CHANNEL,
        .num_banks = 1,
        .num_sensors = MT2701_NUM_SENSORS,
        .vts_index = mt2701_vts_index,
        .cali_val = MT2701_CALIBRATION,
        .num_controller = MT2701_NUM_CONTROLLER,
        .controller_offset = mt2701_tc_offset,
        .need_switch_bank = true,
        .bank_data = {
                {
                        .num_sensors = 3,
                        .sensors = mt2701_bank_data,
                },
        },
        .msr = mt2701_msr,
        .adcpnp = mt2701_adcpnp,
        .sensor_mux_values = mt2701_mux_values,
};

/**
 * The MT2712 thermal controller has one bank, which can read up to
 * four temperature sensors simultaneously. The MT2712 has a total of 4
 * temperature sensors.
 *
 * The thermal core only gets the maximum temperature of this one bank,
 * so the bank concept wouldn't be necessary here. However, the SVS (Smart
 * Voltage Scaling) unit makes its decisions based on the same bank
 * data.
 */
static const struct mtk_thermal_data mt2712_thermal_data = {
        .auxadc_channel = MT2712_TEMP_AUXADC_CHANNEL,
        .num_banks = 1,
        .num_sensors = MT2712_NUM_SENSORS,
        .vts_index = mt2712_vts_index,
        .cali_val = MT2712_CALIBRATION,
        .num_controller = MT2712_NUM_CONTROLLER,
        .controller_offset = mt2712_tc_offset,
        .need_switch_bank = true,
        .bank_data = {
                {
                        .num_sensors = 4,
                        .sensors = mt2712_bank_data,
                },
        },
        .msr = mt2712_msr,
        .adcpnp = mt2712_adcpnp,
        .sensor_mux_values = mt2712_mux_values,
};

/*
 * MT7622 have only one sensing point which uses AUXADC Channel 11 for raw data
 * access.
 */
static const struct mtk_thermal_data mt7622_thermal_data = {
        .auxadc_channel = MT7622_TEMP_AUXADC_CHANNEL,
        .num_banks = MT7622_NUM_ZONES,
        .num_sensors = MT7622_NUM_SENSORS,
        .vts_index = mt7622_vts_index,
        .cali_val = MT7622_CALIBRATION,
        .num_controller = MT7622_NUM_CONTROLLER,
        .controller_offset = mt7622_tc_offset,
        .need_switch_bank = true,
        .bank_data = {
                {
                        .num_sensors = 1,
                        .sensors = mt7622_bank_data,
                },
        },
        .msr = mt7622_msr,
        .adcpnp = mt7622_adcpnp,
        .sensor_mux_values = mt7622_mux_values,
};

/**
 * The MT8183 thermal controller has one bank for the current SW framework.
 * The MT8183 has a total of 6 temperature sensors.
 * There are two thermal controller to control the six sensor.
 * The first one bind 2 sensor, and the other bind 4 sensors.
 * The thermal core only gets the maximum temperature of all sensor, so
 * the bank concept wouldn't be necessary here. However, the SVS (Smart
 * Voltage Scaling) unit makes its decisions based on the same bank
 * data, and this indeed needs the temperatures of the individual banks
 * for making better decisions.
 */

static const struct mtk_thermal_data mt8183_thermal_data = {
        .auxadc_channel = MT8183_TEMP_AUXADC_CHANNEL,
        .num_banks = MT8183_NUM_SENSORS_PER_ZONE,
        .num_sensors = MT8183_NUM_SENSORS,
        .vts_index = mt8183_vts_index,
        .cali_val = MT8183_CALIBRATION,
        .num_controller = MT8183_NUM_CONTROLLER,
        .controller_offset = mt8183_tc_offset,
        .need_switch_bank = false,
        .bank_data = {
                {
                        .num_sensors = 6,
                        .sensors = mt8183_bank_data,
                },
        },

        .msr = mt8183_msr,
        .adcpnp = mt8183_adcpnp,
        .sensor_mux_values = mt8183_mux_values,
};

/**
 * raw_to_mcelsius - convert a raw ADC value to mcelsius
 * @mt:         The thermal controller
 * @raw:        raw ADC value
 *
 * This converts the raw ADC value to mcelsius using the SoC specific
 * calibration constants
 */
static int raw_to_mcelsius(struct mtk_thermal *mt, int sensno, s32 raw)
{
        s32 tmp;

        raw &= 0xfff;

        tmp = 203450520 << 3;
        tmp /= mt->conf->cali_val + mt->o_slope;
        tmp /= 10000 + mt->adc_ge;
        tmp *= raw - mt->vts[sensno] - 3350;
        tmp >>= 3;

        return mt->degc_cali * 500 - tmp;
}

/**
 * mtk_thermal_get_bank - get bank
 * @bank:       The bank
 *
 * The bank registers are banked, we have to select a bank in the
 * PTPCORESEL register to access it.
 */
static void mtk_thermal_get_bank(struct mtk_thermal_bank *bank)
{
        struct mtk_thermal *mt = bank->mt;
        u32 val;

        if (mt->conf->need_switch_bank) {
                mutex_lock(&mt->lock);

                val = readl(mt->thermal_base + PTPCORESEL);
                val &= ~0xf;
                val |= bank->id;
                writel(val, mt->thermal_base + PTPCORESEL);
        }
}

/**
 * mtk_thermal_put_bank - release bank
 * @bank:       The bank
 *
 * release a bank previously taken with mtk_thermal_get_bank,
 */
static void mtk_thermal_put_bank(struct mtk_thermal_bank *bank)
{
        struct mtk_thermal *mt = bank->mt;

        if (mt->conf->need_switch_bank)
                mutex_unlock(&mt->lock);
}

/**
 * mtk_thermal_bank_temperature - get the temperature of a bank
 * @bank:       The bank
 *
 * The temperature of a bank is considered the maximum temperature of
 * the sensors associated to the bank.
 */
static int mtk_thermal_bank_temperature(struct mtk_thermal_bank *bank)
{
        struct mtk_thermal *mt = bank->mt;
        const struct mtk_thermal_data *conf = mt->conf;
        int i, temp = INT_MIN, max = INT_MIN;
        u32 raw;

        for (i = 0; i < conf->bank_data[bank->id].num_sensors; i++) {
                raw = readl(mt->thermal_base +
                            conf->msr[conf->bank_data[bank->id].sensors[i]]);

                temp = raw_to_mcelsius(mt,
                                       conf->bank_data[bank->id].sensors[i],
                                       raw);

                /*
                 * The first read of a sensor often contains very high bogus
                 * temperature value. Filter these out so that the system does
                 * not immediately shut down.
                 */
                if (temp > 200000)
                        temp = 0;

                if (temp > max)
                        max = temp;
        }

        return max;
}

static int mtk_read_temp(void *data, int *temperature)
{
        struct mtk_thermal *mt = data;
        int i;
        int tempmax = INT_MIN;

        for (i = 0; i < mt->conf->num_banks; i++) {
                struct mtk_thermal_bank *bank = &mt->banks[i];

                mtk_thermal_get_bank(bank);

                tempmax = max(tempmax, mtk_thermal_bank_temperature(bank));

                mtk_thermal_put_bank(bank);
        }

        *temperature = tempmax;

        return 0;
}

static const struct thermal_zone_of_device_ops mtk_thermal_ops = {
        .get_temp = mtk_read_temp,
};

static void mtk_thermal_init_bank(struct mtk_thermal *mt, int num,
                                  u32 apmixed_phys_base, u32 auxadc_phys_base,
                                  int ctrl_id)
{
        struct mtk_thermal_bank *bank = &mt->banks[num];
        const struct mtk_thermal_data *conf = mt->conf;
        int i;

        int offset = mt->conf->controller_offset[ctrl_id];
        void __iomem *controller_base = mt->thermal_base + offset;

        bank->id = num;
        bank->mt = mt;

        mtk_thermal_get_bank(bank);

        /* bus clock 66M counting unit is 12 * 15.15ns * 256 = 46.540us */
        writel(TEMP_MONCTL1_PERIOD_UNIT(12), controller_base + TEMP_MONCTL1);

        /*
         * filt interval is 1 * 46.540us = 46.54us,
         * sen interval is 429 * 46.540us = 19.96ms
         */
        writel(TEMP_MONCTL2_FILTER_INTERVAL(1) |
                        TEMP_MONCTL2_SENSOR_INTERVAL(429),
                        controller_base + TEMP_MONCTL2);

        /* poll is set to 10u */
        writel(TEMP_AHBPOLL_ADC_POLL_INTERVAL(768),
               controller_base + TEMP_AHBPOLL);

        /* temperature sampling control, 1 sample */
        writel(0x0, controller_base + TEMP_MSRCTL0);

        /* exceed this polling time, IRQ would be inserted */
        writel(0xffffffff, controller_base + TEMP_AHBTO);

        /* number of interrupts per event, 1 is enough */
        writel(0x0, controller_base + TEMP_MONIDET0);
        writel(0x0, controller_base + TEMP_MONIDET1);

        /*
         * The MT8173 thermal controller does not have its own ADC. Instead it
         * uses AHB bus accesses to control the AUXADC. To do this the thermal
         * controller has to be programmed with the physical addresses of the
         * AUXADC registers and with the various bit positions in the AUXADC.
         * Also the thermal controller controls a mux in the APMIXEDSYS register
         * space.
         */

        /*
         * this value will be stored to TEMP_PNPMUXADDR (TEMP_SPARE0)
         * automatically by hw
         */
        writel(BIT(conf->auxadc_channel), controller_base + TEMP_ADCMUX);

        /* AHB address for auxadc mux selection */
        writel(auxadc_phys_base + AUXADC_CON1_CLR_V,
               controller_base + TEMP_ADCMUXADDR);

        /* AHB address for pnp sensor mux selection */
        writel(apmixed_phys_base + APMIXED_SYS_TS_CON1,
               controller_base + TEMP_PNPMUXADDR);

        /* AHB value for auxadc enable */
        writel(BIT(conf->auxadc_channel), controller_base + TEMP_ADCEN);

        /* AHB address for auxadc enable (channel 0 immediate mode selected) */
        writel(auxadc_phys_base + AUXADC_CON1_SET_V,
               controller_base + TEMP_ADCENADDR);

        /* AHB address for auxadc valid bit */
        writel(auxadc_phys_base + AUXADC_DATA(conf->auxadc_channel),
               controller_base + TEMP_ADCVALIDADDR);

        /* AHB address for auxadc voltage output */
        writel(auxadc_phys_base + AUXADC_DATA(conf->auxadc_channel),
               controller_base + TEMP_ADCVOLTADDR);

        /* read valid & voltage are at the same register */
        writel(0x0, controller_base + TEMP_RDCTRL);

        /* indicate where the valid bit is */
        writel(TEMP_ADCVALIDMASK_VALID_HIGH | TEMP_ADCVALIDMASK_VALID_POS(12),
               controller_base + TEMP_ADCVALIDMASK);

        /* no shift */
        writel(0x0, controller_base + TEMP_ADCVOLTAGESHIFT);

        /* enable auxadc mux write transaction */
        writel(TEMP_ADCWRITECTRL_ADC_MUX_WRITE,
                controller_base + TEMP_ADCWRITECTRL);

        for (i = 0; i < conf->bank_data[num].num_sensors; i++)
                writel(conf->sensor_mux_values[conf->bank_data[num].sensors[i]],
                       mt->thermal_base +
                       conf->adcpnp[conf->bank_data[num].sensors[i]]);

        writel((1 << conf->bank_data[num].num_sensors) - 1,
               controller_base + TEMP_MONCTL0);

        writel(TEMP_ADCWRITECTRL_ADC_PNP_WRITE |
               TEMP_ADCWRITECTRL_ADC_MUX_WRITE,
               controller_base + TEMP_ADCWRITECTRL);

        mtk_thermal_put_bank(bank);
}

static u64 of_get_phys_base(struct device_node *np)
{
        u64 size64;
        const __be32 *regaddr_p;

        regaddr_p = of_get_address(np, 0, &size64, NULL);
        if (!regaddr_p)
                return OF_BAD_ADDR;

        return of_translate_address(np, regaddr_p);
}

static int mtk_thermal_get_calibration_data(struct device *dev,
                                            struct mtk_thermal *mt)
{
        struct nvmem_cell *cell;
        u32 *buf;
        size_t len;
        int i, ret = 0;

        /* Start with default values */
        mt->adc_ge = 512;
        for (i = 0; i < mt->conf->num_sensors; i++)
                mt->vts[i] = 260;
        mt->degc_cali = 40;
        mt->o_slope = 0;

        cell = nvmem_cell_get(dev, "calibration-data");
        if (IS_ERR(cell)) {
                if (PTR_ERR(cell) == -EPROBE_DEFER)
                        return PTR_ERR(cell);
                return 0;
        }

        buf = (u32 *)nvmem_cell_read(cell, &len);

        nvmem_cell_put(cell);

        if (IS_ERR(buf))
                return PTR_ERR(buf);

        if (len < 3 * sizeof(u32)) {
                dev_warn(dev, "invalid calibration data\n");
                ret = -EINVAL;
                goto out;
        }

        if (buf[0] & CALIB_BUF0_VALID) {
                mt->adc_ge = CALIB_BUF1_ADC_GE(buf[1]);

                for (i = 0; i < mt->conf->num_sensors; i++) {
                        switch (mt->conf->vts_index[i]) {
                        case VTS1:
                                mt->vts[VTS1] = CALIB_BUF0_VTS_TS1(buf[0]);
                                break;
                        case VTS2:
                                mt->vts[VTS2] = CALIB_BUF0_VTS_TS2(buf[0]);
                                break;
                        case VTS3:
                                mt->vts[VTS3] = CALIB_BUF1_VTS_TS3(buf[1]);
                                break;
                        case VTS4:
                                mt->vts[VTS4] = CALIB_BUF2_VTS_TS4(buf[2]);
                                break;
                        case VTS5:
                                mt->vts[VTS5] = CALIB_BUF2_VTS_TS5(buf[2]);
                                break;
                        case VTSABB:
                                mt->vts[VTSABB] = CALIB_BUF2_VTS_TSABB(buf[2]);
                                break;
                        default:
                                break;
                        }
                }

                mt->degc_cali = CALIB_BUF0_DEGC_CALI(buf[0]);
                if (CALIB_BUF1_ID(buf[1]) &
                    CALIB_BUF0_O_SLOPE_SIGN(buf[0]))
                        mt->o_slope = -CALIB_BUF0_O_SLOPE(buf[0]);
                else
                        mt->o_slope = CALIB_BUF0_O_SLOPE(buf[0]);
        } else {
                dev_info(dev, "Device not calibrated, using default calibration values\n");
        }

out:
        kfree(buf);

        return ret;
}

static const struct of_device_id mtk_thermal_of_match[] = {
        {
                .compatible = "mediatek,mt8173-thermal",
                .data = (void *)&mt8173_thermal_data,
        },
        {
                .compatible = "mediatek,mt2701-thermal",
                .data = (void *)&mt2701_thermal_data,
        },
        {
                .compatible = "mediatek,mt2712-thermal",
                .data = (void *)&mt2712_thermal_data,
        },
        {
                .compatible = "mediatek,mt7622-thermal",
                .data = (void *)&mt7622_thermal_data,
        },
        {
                .compatible = "mediatek,mt8183-thermal",
                .data = (void *)&mt8183_thermal_data,
        }, {
        },
};
MODULE_DEVICE_TABLE(of, mtk_thermal_of_match);

static int mtk_thermal_probe(struct platform_device *pdev)
{
        int ret, i, ctrl_id;
        struct device_node *auxadc, *apmixedsys, *np = pdev->dev.of_node;
        struct mtk_thermal *mt;
        struct resource *res;
        u64 auxadc_phys_base, apmixed_phys_base;
        struct thermal_zone_device *tzdev;

        mt = devm_kzalloc(&pdev->dev, sizeof(*mt), GFP_KERNEL);
        if (!mt)
                return -ENOMEM;

        mt->conf = of_device_get_match_data(&pdev->dev);

        mt->clk_peri_therm = devm_clk_get(&pdev->dev, "therm");
        if (IS_ERR(mt->clk_peri_therm))
                return PTR_ERR(mt->clk_peri_therm);

        mt->clk_auxadc = devm_clk_get(&pdev->dev, "auxadc");
        if (IS_ERR(mt->clk_auxadc))
                return PTR_ERR(mt->clk_auxadc);

        res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
        mt->thermal_base = devm_ioremap_resource(&pdev->dev, res);
        if (IS_ERR(mt->thermal_base))
                return PTR_ERR(mt->thermal_base);

        ret = mtk_thermal_get_calibration_data(&pdev->dev, mt);
        if (ret)
                return ret;

        mutex_init(&mt->lock);

        mt->dev = &pdev->dev;

        auxadc = of_parse_phandle(np, "mediatek,auxadc", 0);
        if (!auxadc) {
                dev_err(&pdev->dev, "missing auxadc node\n");
                return -ENODEV;
        }

        auxadc_phys_base = of_get_phys_base(auxadc);

        of_node_put(auxadc);

        if (auxadc_phys_base == OF_BAD_ADDR) {
                dev_err(&pdev->dev, "Can't get auxadc phys address\n");
                return -EINVAL;
        }

        apmixedsys = of_parse_phandle(np, "mediatek,apmixedsys", 0);
        if (!apmixedsys) {
                dev_err(&pdev->dev, "missing apmixedsys node\n");
                return -ENODEV;
        }

        apmixed_phys_base = of_get_phys_base(apmixedsys);

        of_node_put(apmixedsys);

        if (apmixed_phys_base == OF_BAD_ADDR) {
                dev_err(&pdev->dev, "Can't get auxadc phys address\n");
                return -EINVAL;
        }

        ret = device_reset(&pdev->dev);
        if (ret)
                return ret;

        ret = clk_prepare_enable(mt->clk_auxadc);
        if (ret) {
                dev_err(&pdev->dev, "Can't enable auxadc clk: %d\n", ret);
                return ret;
        }

        ret = clk_prepare_enable(mt->clk_peri_therm);
        if (ret) {
                dev_err(&pdev->dev, "Can't enable peri clk: %d\n", ret);
                goto err_disable_clk_auxadc;
        }

        for (ctrl_id = 0; ctrl_id < mt->conf->num_controller ; ctrl_id++)
                for (i = 0; i < mt->conf->num_banks; i++)
                        mtk_thermal_init_bank(mt, i, apmixed_phys_base,
                                              auxadc_phys_base, ctrl_id);

        platform_set_drvdata(pdev, mt);

        tzdev = devm_thermal_zone_of_sensor_register(&pdev->dev, 0, mt,
                                                     &mtk_thermal_ops);
        if (IS_ERR(tzdev)) {
                ret = PTR_ERR(tzdev);
                goto err_disable_clk_peri_therm;
        }

        return 0;

err_disable_clk_peri_therm:
        clk_disable_unprepare(mt->clk_peri_therm);
err_disable_clk_auxadc:
        clk_disable_unprepare(mt->clk_auxadc);

        return ret;
}

static int mtk_thermal_remove(struct platform_device *pdev)
{
        struct mtk_thermal *mt = platform_get_drvdata(pdev);

        clk_disable_unprepare(mt->clk_peri_therm);
        clk_disable_unprepare(mt->clk_auxadc);

        return 0;
}

static struct platform_driver mtk_thermal_driver = {
        .probe = mtk_thermal_probe,
        .remove = mtk_thermal_remove,
        .driver = {
                .name = "mtk-thermal",
                .of_match_table = mtk_thermal_of_match,
        },
};

module_platform_driver(mtk_thermal_driver);

MODULE_AUTHOR("Michael Kao <michael.kao@mediatek.com>");
MODULE_AUTHOR("Louis Yu <louis.yu@mediatek.com>");
MODULE_AUTHOR("Dawei Chien <dawei.chien@mediatek.com>");
MODULE_AUTHOR("Sascha Hauer <s.hauer@pengutronix.de>");
MODULE_AUTHOR("Hanyi Wu <hanyi.wu@mediatek.com>");
MODULE_DESCRIPTION("Mediatek thermal driver");
MODULE_LICENSE("GPL v2");