dt-bindings: mtd: ingenic: Use standard ecc-engine property

[linux/fpc-iii.git] / drivers / usb / wusbcore / wa-xfer.c

// SPDX-License-Identifier: GPL-2.0
/*
 * WUSB Wire Adapter
 * Data transfer and URB enqueing
 *
 * Copyright (C) 2005-2006 Intel Corporation
 * Inaky Perez-Gonzalez <inaky.perez-gonzalez@intel.com>
 *
 * How transfers work: get a buffer, break it up in segments (segment
 * size is a multiple of the maxpacket size). For each segment issue a
 * segment request (struct wa_xfer_*), then send the data buffer if
 * out or nothing if in (all over the DTO endpoint).
 *
 * For each submitted segment request, a notification will come over
 * the NEP endpoint and a transfer result (struct xfer_result) will
 * arrive in the DTI URB. Read it, get the xfer ID, see if there is
 * data coming (inbound transfer), schedule a read and handle it.
 *
 * Sounds simple, it is a pain to implement.
 *
 *
 * ENTRY POINTS
 *
 *   FIXME
 *
 * LIFE CYCLE / STATE DIAGRAM
 *
 *   FIXME
 *
 * THIS CODE IS DISGUSTING
 *
 *   Warned you are; it's my second try and still not happy with it.
 *
 * NOTES:
 *
 *   - No iso
 *
 *   - Supports DMA xfers, control, bulk and maybe interrupt
 *
 *   - Does not recycle unused rpipes
 *
 *     An rpipe is assigned to an endpoint the first time it is used,
 *     and then it's there, assigned, until the endpoint is disabled
 *     (destroyed [{h,d}wahc_op_ep_disable()]. The assignment of the
 *     rpipe to the endpoint is done under the wa->rpipe_sem semaphore
 *     (should be a mutex).
 *
 *     Two methods it could be done:
 *
 *     (a) set up a timer every time an rpipe's use count drops to 1
 *         (which means unused) or when a transfer ends. Reset the
 *         timer when a xfer is queued. If the timer expires, release
 *         the rpipe [see rpipe_ep_disable()].
 *
 *     (b) when looking for free rpipes to attach [rpipe_get_by_ep()],
 *         when none are found go over the list, check their endpoint
 *         and their activity record (if no last-xfer-done-ts in the
 *         last x seconds) take it
 *
 *     However, due to the fact that we have a set of limited
 *     resources (max-segments-at-the-same-time per xfer,
 *     xfers-per-ripe, blocks-per-rpipe, rpipes-per-host), at the end
 *     we are going to have to rebuild all this based on an scheduler,
 *     to where we have a list of transactions to do and based on the
 *     availability of the different required components (blocks,
 *     rpipes, segment slots, etc), we go scheduling them. Painful.
 */
#include <linux/spinlock.h>
#include <linux/slab.h>
#include <linux/hash.h>
#include <linux/ratelimit.h>
#include <linux/export.h>
#include <linux/scatterlist.h>

#include "wa-hc.h"
#include "wusbhc.h"

enum {
        /* [WUSB] section 8.3.3 allocates 7 bits for the segment index. */
        WA_SEGS_MAX = 128,
};

enum wa_seg_status {
        WA_SEG_NOTREADY,
        WA_SEG_READY,
        WA_SEG_DELAYED,
        WA_SEG_SUBMITTED,
        WA_SEG_PENDING,
        WA_SEG_DTI_PENDING,
        WA_SEG_DONE,
        WA_SEG_ERROR,
        WA_SEG_ABORTED,
};

static void wa_xfer_delayed_run(struct wa_rpipe *);
static int __wa_xfer_delayed_run(struct wa_rpipe *rpipe, int *dto_waiting);

/*
 * Life cycle governed by 'struct urb' (the refcount of the struct is
 * that of the 'struct urb' and usb_free_urb() would free the whole
 * struct).
 */
struct wa_seg {
        struct urb tr_urb;              /* transfer request urb. */
        struct urb *isoc_pack_desc_urb; /* for isoc packet descriptor. */
        struct urb *dto_urb;            /* for data output. */
        struct list_head list_node;     /* for rpipe->req_list */
        struct wa_xfer *xfer;           /* out xfer */
        u8 index;                       /* which segment we are */
        int isoc_frame_count;   /* number of isoc frames in this segment. */
        int isoc_frame_offset;  /* starting frame offset in the xfer URB. */
        /* Isoc frame that the current transfer buffer corresponds to. */
        int isoc_frame_index;
        int isoc_size;  /* size of all isoc frames sent by this seg. */
        enum wa_seg_status status;
        ssize_t result;                 /* bytes xfered or error */
        struct wa_xfer_hdr xfer_hdr;
};

static inline void wa_seg_init(struct wa_seg *seg)
{
        usb_init_urb(&seg->tr_urb);

        /* set the remaining memory to 0. */
        memset(((void *)seg) + sizeof(seg->tr_urb), 0,
                sizeof(*seg) - sizeof(seg->tr_urb));
}

/*
 * Protected by xfer->lock
 *
 */
struct wa_xfer {
        struct kref refcnt;
        struct list_head list_node;
        spinlock_t lock;
        u32 id;

        struct wahc *wa;                /* Wire adapter we are plugged to */
        struct usb_host_endpoint *ep;
        struct urb *urb;                /* URB we are transferring for */
        struct wa_seg **seg;            /* transfer segments */
        u8 segs, segs_submitted, segs_done;
        unsigned is_inbound:1;
        unsigned is_dma:1;
        size_t seg_size;
        int result;

        gfp_t gfp;                      /* allocation mask */

        struct wusb_dev *wusb_dev;      /* for activity timestamps */
};

static void __wa_populate_dto_urb_isoc(struct wa_xfer *xfer,
        struct wa_seg *seg, int curr_iso_frame);
static void wa_complete_remaining_xfer_segs(struct wa_xfer *xfer,
                int starting_index, enum wa_seg_status status);

static inline void wa_xfer_init(struct wa_xfer *xfer)
{
        kref_init(&xfer->refcnt);
        INIT_LIST_HEAD(&xfer->list_node);
        spin_lock_init(&xfer->lock);
}

/*
 * Destroy a transfer structure
 *
 * Note that freeing xfer->seg[cnt]->tr_urb will free the containing
 * xfer->seg[cnt] memory that was allocated by __wa_xfer_setup_segs.
 */
static void wa_xfer_destroy(struct kref *_xfer)
{
        struct wa_xfer *xfer = container_of(_xfer, struct wa_xfer, refcnt);
        if (xfer->seg) {
                unsigned cnt;
                for (cnt = 0; cnt < xfer->segs; cnt++) {
                        struct wa_seg *seg = xfer->seg[cnt];
                        if (seg) {
                                usb_free_urb(seg->isoc_pack_desc_urb);
                                if (seg->dto_urb) {
                                        kfree(seg->dto_urb->sg);
                                        usb_free_urb(seg->dto_urb);
                                }
                                usb_free_urb(&seg->tr_urb);
                        }
                }
                kfree(xfer->seg);
        }
        kfree(xfer);
}

static void wa_xfer_get(struct wa_xfer *xfer)
{
        kref_get(&xfer->refcnt);
}

static void wa_xfer_put(struct wa_xfer *xfer)
{
        kref_put(&xfer->refcnt, wa_xfer_destroy);
}

/*
 * Try to get exclusive access to the DTO endpoint resource.  Return true
 * if successful.
 */
static inline int __wa_dto_try_get(struct wahc *wa)
{
        return (test_and_set_bit(0, &wa->dto_in_use) == 0);
}

/* Release the DTO endpoint resource. */
static inline void __wa_dto_put(struct wahc *wa)
{
        clear_bit_unlock(0, &wa->dto_in_use);
}

/* Service RPIPEs that are waiting on the DTO resource. */
static void wa_check_for_delayed_rpipes(struct wahc *wa)
{
        unsigned long flags;
        int dto_waiting = 0;
        struct wa_rpipe *rpipe;

        spin_lock_irqsave(&wa->rpipe_lock, flags);
        while (!list_empty(&wa->rpipe_delayed_list) && !dto_waiting) {
                rpipe = list_first_entry(&wa->rpipe_delayed_list,
                                struct wa_rpipe, list_node);
                __wa_xfer_delayed_run(rpipe, &dto_waiting);
                /* remove this RPIPE from the list if it is not waiting. */
                if (!dto_waiting) {
                        pr_debug("%s: RPIPE %d serviced and removed from delayed list.\n",
                                __func__,
                                le16_to_cpu(rpipe->descr.wRPipeIndex));
                        list_del_init(&rpipe->list_node);
                }
        }
        spin_unlock_irqrestore(&wa->rpipe_lock, flags);
}

/* add this RPIPE to the end of the delayed RPIPE list. */
static void wa_add_delayed_rpipe(struct wahc *wa, struct wa_rpipe *rpipe)
{
        unsigned long flags;

        spin_lock_irqsave(&wa->rpipe_lock, flags);
        /* add rpipe to the list if it is not already on it. */
        if (list_empty(&rpipe->list_node)) {
                pr_debug("%s: adding RPIPE %d to the delayed list.\n",
                        __func__, le16_to_cpu(rpipe->descr.wRPipeIndex));
                list_add_tail(&rpipe->list_node, &wa->rpipe_delayed_list);
        }
        spin_unlock_irqrestore(&wa->rpipe_lock, flags);
}

/*
 * xfer is referenced
 *
 * xfer->lock has to be unlocked
 *
 * We take xfer->lock for setting the result; this is a barrier
 * against drivers/usb/core/hcd.c:unlink1() being called after we call
 * usb_hcd_giveback_urb() and wa_urb_dequeue() trying to get a
 * reference to the transfer.
 */
static void wa_xfer_giveback(struct wa_xfer *xfer)
{
        unsigned long flags;

        spin_lock_irqsave(&xfer->wa->xfer_list_lock, flags);
        list_del_init(&xfer->list_node);
        usb_hcd_unlink_urb_from_ep(&(xfer->wa->wusb->usb_hcd), xfer->urb);
        spin_unlock_irqrestore(&xfer->wa->xfer_list_lock, flags);
        /* FIXME: segmentation broken -- kills DWA */
        wusbhc_giveback_urb(xfer->wa->wusb, xfer->urb, xfer->result);
        wa_put(xfer->wa);
        wa_xfer_put(xfer);
}

/*
 * xfer is referenced
 *
 * xfer->lock has to be unlocked
 */
static void wa_xfer_completion(struct wa_xfer *xfer)
{
        if (xfer->wusb_dev)
                wusb_dev_put(xfer->wusb_dev);
        rpipe_put(xfer->ep->hcpriv);
        wa_xfer_giveback(xfer);
}

/*
 * Initialize a transfer's ID
 *
 * We need to use a sequential number; if we use the pointer or the
 * hash of the pointer, it can repeat over sequential transfers and
 * then it will confuse the HWA....wonder why in hell they put a 32
 * bit handle in there then.
 */
static void wa_xfer_id_init(struct wa_xfer *xfer)
{
        xfer->id = atomic_add_return(1, &xfer->wa->xfer_id_count);
}

/* Return the xfer's ID. */
static inline u32 wa_xfer_id(struct wa_xfer *xfer)
{
        return xfer->id;
}

/* Return the xfer's ID in transport format (little endian). */
static inline __le32 wa_xfer_id_le32(struct wa_xfer *xfer)
{
        return cpu_to_le32(xfer->id);
}

/*
 * If transfer is done, wrap it up and return true
 *
 * xfer->lock has to be locked
 */
static unsigned __wa_xfer_is_done(struct wa_xfer *xfer)
{
        struct device *dev = &xfer->wa->usb_iface->dev;
        unsigned result, cnt;
        struct wa_seg *seg;
        struct urb *urb = xfer->urb;
        unsigned found_short = 0;

        result = xfer->segs_done == xfer->segs_submitted;
        if (result == 0)
                goto out;
        urb->actual_length = 0;
        for (cnt = 0; cnt < xfer->segs; cnt++) {
                seg = xfer->seg[cnt];
                switch (seg->status) {
                case WA_SEG_DONE:
                        if (found_short && seg->result > 0) {
                                dev_dbg(dev, "xfer %p ID %08X#%u: bad short segments (%zu)\n",
                                        xfer, wa_xfer_id(xfer), cnt,
                                        seg->result);
                                urb->status = -EINVAL;
                                goto out;
                        }
                        urb->actual_length += seg->result;
                        if (!(usb_pipeisoc(xfer->urb->pipe))
                                && seg->result < xfer->seg_size
                            && cnt != xfer->segs-1)
                                found_short = 1;
                        dev_dbg(dev, "xfer %p ID %08X#%u: DONE short %d "
                                "result %zu urb->actual_length %d\n",
                                xfer, wa_xfer_id(xfer), seg->index, found_short,
                                seg->result, urb->actual_length);
                        break;
                case WA_SEG_ERROR:
                        xfer->result = seg->result;
                        dev_dbg(dev, "xfer %p ID %08X#%u: ERROR result %zi(0x%08zX)\n",
                                xfer, wa_xfer_id(xfer), seg->index, seg->result,
                                seg->result);
                        goto out;
                case WA_SEG_ABORTED:
                        xfer->result = seg->result;
                        dev_dbg(dev, "xfer %p ID %08X#%u: ABORTED result %zi(0x%08zX)\n",
                                xfer, wa_xfer_id(xfer), seg->index, seg->result,
                                seg->result);
                        goto out;
                default:
                        dev_warn(dev, "xfer %p ID %08X#%u: is_done bad state %d\n",
                                 xfer, wa_xfer_id(xfer), cnt, seg->status);
                        xfer->result = -EINVAL;
                        goto out;
                }
        }
        xfer->result = 0;
out:
        return result;
}

/*
 * Mark the given segment as done.  Return true if this completes the xfer.
 * This should only be called for segs that have been submitted to an RPIPE.
 * Delayed segs are not marked as submitted so they do not need to be marked
 * as done when cleaning up.
 *
 * xfer->lock has to be locked
 */
static unsigned __wa_xfer_mark_seg_as_done(struct wa_xfer *xfer,
        struct wa_seg *seg, enum wa_seg_status status)
{
        seg->status = status;
        xfer->segs_done++;

        /* check for done. */
        return __wa_xfer_is_done(xfer);
}

/*
 * Search for a transfer list ID on the HCD's URB list
 *
 * For 32 bit architectures, we use the pointer itself; for 64 bits, a
 * 32-bit hash of the pointer.
 *
 * @returns NULL if not found.
 */
static struct wa_xfer *wa_xfer_get_by_id(struct wahc *wa, u32 id)
{
        unsigned long flags;
        struct wa_xfer *xfer_itr;
        spin_lock_irqsave(&wa->xfer_list_lock, flags);
        list_for_each_entry(xfer_itr, &wa->xfer_list, list_node) {
                if (id == xfer_itr->id) {
                        wa_xfer_get(xfer_itr);
                        goto out;
                }
        }
        xfer_itr = NULL;
out:
        spin_unlock_irqrestore(&wa->xfer_list_lock, flags);
        return xfer_itr;
}

struct wa_xfer_abort_buffer {
        struct urb urb;
        struct wahc *wa;
        struct wa_xfer_abort cmd;
};

static void __wa_xfer_abort_cb(struct urb *urb)
{
        struct wa_xfer_abort_buffer *b = urb->context;
        struct wahc *wa = b->wa;

        /*
         * If the abort request URB failed, then the HWA did not get the abort
         * command.  Forcibly clean up the xfer without waiting for a Transfer
         * Result from the HWA.
         */
        if (urb->status < 0) {
                struct wa_xfer *xfer;
                struct device *dev = &wa->usb_iface->dev;

                xfer = wa_xfer_get_by_id(wa, le32_to_cpu(b->cmd.dwTransferID));
                dev_err(dev, "%s: Transfer Abort request failed. result: %d\n",
                        __func__, urb->status);
                if (xfer) {
                        unsigned long flags;
                        int done, seg_index = 0;
                        struct wa_rpipe *rpipe = xfer->ep->hcpriv;

                        dev_err(dev, "%s: cleaning up xfer %p ID 0x%08X.\n",
                                __func__, xfer, wa_xfer_id(xfer));
                        spin_lock_irqsave(&xfer->lock, flags);
                        /* skip done segs. */
                        while (seg_index < xfer->segs) {
                                struct wa_seg *seg = xfer->seg[seg_index];

                                if ((seg->status == WA_SEG_DONE) ||
                                        (seg->status == WA_SEG_ERROR)) {
                                        ++seg_index;
                                } else {
                                        break;
                                }
                        }
                        /* mark remaining segs as aborted. */
                        wa_complete_remaining_xfer_segs(xfer, seg_index,
                                WA_SEG_ABORTED);
                        done = __wa_xfer_is_done(xfer);
                        spin_unlock_irqrestore(&xfer->lock, flags);
                        if (done)
                                wa_xfer_completion(xfer);
                        wa_xfer_delayed_run(rpipe);
                        wa_xfer_put(xfer);
                } else {
                        dev_err(dev, "%s: xfer ID 0x%08X already gone.\n",
                                 __func__, le32_to_cpu(b->cmd.dwTransferID));
                }
        }

        wa_put(wa);     /* taken in __wa_xfer_abort */
        usb_put_urb(&b->urb);
}

/*
 * Aborts an ongoing transaction
 *
 * Assumes the transfer is referenced and locked and in a submitted
 * state (mainly that there is an endpoint/rpipe assigned).
 *
 * The callback (see above) does nothing but freeing up the data by
 * putting the URB. Because the URB is allocated at the head of the
 * struct, the whole space we allocated is kfreed. *
 */
static int __wa_xfer_abort(struct wa_xfer *xfer)
{
        int result = -ENOMEM;
        struct device *dev = &xfer->wa->usb_iface->dev;
        struct wa_xfer_abort_buffer *b;
        struct wa_rpipe *rpipe = xfer->ep->hcpriv;

        b = kmalloc(sizeof(*b), GFP_ATOMIC);
        if (b == NULL)
                goto error_kmalloc;
        b->cmd.bLength =  sizeof(b->cmd);
        b->cmd.bRequestType = WA_XFER_ABORT;
        b->cmd.wRPipe = rpipe->descr.wRPipeIndex;
        b->cmd.dwTransferID = wa_xfer_id_le32(xfer);
        b->wa = wa_get(xfer->wa);

        usb_init_urb(&b->urb);
        usb_fill_bulk_urb(&b->urb, xfer->wa->usb_dev,
                usb_sndbulkpipe(xfer->wa->usb_dev,
                                xfer->wa->dto_epd->bEndpointAddress),
                &b->cmd, sizeof(b->cmd), __wa_xfer_abort_cb, b);
        result = usb_submit_urb(&b->urb, GFP_ATOMIC);
        if (result < 0)
                goto error_submit;
        return result;                          /* callback frees! */


error_submit:
        wa_put(xfer->wa);
        if (printk_ratelimit())
                dev_err(dev, "xfer %p: Can't submit abort request: %d\n",
                        xfer, result);
        kfree(b);
error_kmalloc:
        return result;

}

/*
 * Calculate the number of isoc frames starting from isoc_frame_offset
 * that will fit a in transfer segment.
 */
static int __wa_seg_calculate_isoc_frame_count(struct wa_xfer *xfer,
        int isoc_frame_offset, int *total_size)
{
        int segment_size = 0, frame_count = 0;
        int index = isoc_frame_offset;
        struct usb_iso_packet_descriptor *iso_frame_desc =
                xfer->urb->iso_frame_desc;

        while ((index < xfer->urb->number_of_packets)
                && ((segment_size + iso_frame_desc[index].length)
                                <= xfer->seg_size)) {
                /*
                 * For Alereon HWA devices, only include an isoc frame in an
                 * out segment if it is physically contiguous with the previous
                 * frame.  This is required because those devices expect
                 * the isoc frames to be sent as a single USB transaction as
                 * opposed to one transaction per frame with standard HWA.
                 */
                if ((xfer->wa->quirks & WUSB_QUIRK_ALEREON_HWA_CONCAT_ISOC)
                        && (xfer->is_inbound == 0)
                        && (index > isoc_frame_offset)
                        && ((iso_frame_desc[index - 1].offset +
                                iso_frame_desc[index - 1].length) !=
                                iso_frame_desc[index].offset))
                        break;

                /* this frame fits. count it. */
                ++frame_count;
                segment_size += iso_frame_desc[index].length;

                /* move to the next isoc frame. */
                ++index;
        }

        *total_size = segment_size;
        return frame_count;
}

/*
 *
 * @returns < 0 on error, transfer segment request size if ok
 */
static ssize_t __wa_xfer_setup_sizes(struct wa_xfer *xfer,
                                     enum wa_xfer_type *pxfer_type)
{
        ssize_t result;
        struct device *dev = &xfer->wa->usb_iface->dev;
        size_t maxpktsize;
        struct urb *urb = xfer->urb;
        struct wa_rpipe *rpipe = xfer->ep->hcpriv;

        switch (rpipe->descr.bmAttribute & 0x3) {
        case USB_ENDPOINT_XFER_CONTROL:
                *pxfer_type = WA_XFER_TYPE_CTL;
                result = sizeof(struct wa_xfer_ctl);
                break;
        case USB_ENDPOINT_XFER_INT:
        case USB_ENDPOINT_XFER_BULK:
                *pxfer_type = WA_XFER_TYPE_BI;
                result = sizeof(struct wa_xfer_bi);
                break;
        case USB_ENDPOINT_XFER_ISOC:
                *pxfer_type = WA_XFER_TYPE_ISO;
                result = sizeof(struct wa_xfer_hwaiso);
                break;
        default:
                /* never happens */
                BUG();
                result = -EINVAL;       /* shut gcc up */
        }
        xfer->is_inbound = urb->pipe & USB_DIR_IN ? 1 : 0;
        xfer->is_dma = urb->transfer_flags & URB_NO_TRANSFER_DMA_MAP ? 1 : 0;

        maxpktsize = le16_to_cpu(rpipe->descr.wMaxPacketSize);
        xfer->seg_size = le16_to_cpu(rpipe->descr.wBlocks)
                * 1 << (xfer->wa->wa_descr->bRPipeBlockSize - 1);
        /* Compute the segment size and make sure it is a multiple of
         * the maxpktsize (WUSB1.0[8.3.3.1])...not really too much of
         * a check (FIXME) */
        if (xfer->seg_size < maxpktsize) {
                dev_err(dev,
                        "HW BUG? seg_size %zu smaller than maxpktsize %zu\n",
                        xfer->seg_size, maxpktsize);
                result = -EINVAL;
                goto error;
        }
        xfer->seg_size = (xfer->seg_size / maxpktsize) * maxpktsize;
        if ((rpipe->descr.bmAttribute & 0x3) == USB_ENDPOINT_XFER_ISOC) {
                int index = 0;

                xfer->segs = 0;
                /*
                 * loop over urb->number_of_packets to determine how many
                 * xfer segments will be needed to send the isoc frames.
                 */
                while (index < urb->number_of_packets) {
                        int seg_size; /* don't care. */
                        index += __wa_seg_calculate_isoc_frame_count(xfer,
                                        index, &seg_size);
                        ++xfer->segs;
                }
        } else {
                xfer->segs = DIV_ROUND_UP(urb->transfer_buffer_length,
                                                xfer->seg_size);
                if (xfer->segs == 0 && *pxfer_type == WA_XFER_TYPE_CTL)
                        xfer->segs = 1;
        }

        if (xfer->segs > WA_SEGS_MAX) {
                dev_err(dev, "BUG? oops, number of segments %zu bigger than %d\n",
                        (urb->transfer_buffer_length/xfer->seg_size),
                        WA_SEGS_MAX);
                result = -EINVAL;
                goto error;
        }
error:
        return result;
}

static void __wa_setup_isoc_packet_descr(
                struct wa_xfer_packet_info_hwaiso *packet_desc,
                struct wa_xfer *xfer,
                struct wa_seg *seg) {
        struct usb_iso_packet_descriptor *iso_frame_desc =
                xfer->urb->iso_frame_desc;
        int frame_index;

        /* populate isoc packet descriptor. */
        packet_desc->bPacketType = WA_XFER_ISO_PACKET_INFO;
        packet_desc->wLength = cpu_to_le16(struct_size(packet_desc,
                                           PacketLength,
                                           seg->isoc_frame_count));
        for (frame_index = 0; frame_index < seg->isoc_frame_count;
                ++frame_index) {
                int offset_index = frame_index + seg->isoc_frame_offset;
                packet_desc->PacketLength[frame_index] =
                        cpu_to_le16(iso_frame_desc[offset_index].length);
        }
}


/* Fill in the common request header and xfer-type specific data. */
static void __wa_xfer_setup_hdr0(struct wa_xfer *xfer,
                                 struct wa_xfer_hdr *xfer_hdr0,
                                 enum wa_xfer_type xfer_type,
                                 size_t xfer_hdr_size)
{
        struct wa_rpipe *rpipe = xfer->ep->hcpriv;
        struct wa_seg *seg = xfer->seg[0];

        xfer_hdr0 = &seg->xfer_hdr;
        xfer_hdr0->bLength = xfer_hdr_size;
        xfer_hdr0->bRequestType = xfer_type;
        xfer_hdr0->wRPipe = rpipe->descr.wRPipeIndex;
        xfer_hdr0->dwTransferID = wa_xfer_id_le32(xfer);
        xfer_hdr0->bTransferSegment = 0;
        switch (xfer_type) {
        case WA_XFER_TYPE_CTL: {
                struct wa_xfer_ctl *xfer_ctl =
                        container_of(xfer_hdr0, struct wa_xfer_ctl, hdr);
                xfer_ctl->bmAttribute = xfer->is_inbound ? 1 : 0;
                memcpy(&xfer_ctl->baSetupData, xfer->urb->setup_packet,
                       sizeof(xfer_ctl->baSetupData));
                break;
        }
        case WA_XFER_TYPE_BI:
                break;
        case WA_XFER_TYPE_ISO: {
                struct wa_xfer_hwaiso *xfer_iso =
                        container_of(xfer_hdr0, struct wa_xfer_hwaiso, hdr);
                struct wa_xfer_packet_info_hwaiso *packet_desc =
                        ((void *)xfer_iso) + xfer_hdr_size;

                /* populate the isoc section of the transfer request. */
                xfer_iso->dwNumOfPackets = cpu_to_le32(seg->isoc_frame_count);
                /* populate isoc packet descriptor. */
                __wa_setup_isoc_packet_descr(packet_desc, xfer, seg);
                break;
        }
        default:
                BUG();
        };
}

/*
 * Callback for the OUT data phase of the segment request
 *
 * Check wa_seg_tr_cb(); most comments also apply here because this
 * function does almost the same thing and they work closely
 * together.
 *
 * If the seg request has failed but this DTO phase has succeeded,
 * wa_seg_tr_cb() has already failed the segment and moved the
 * status to WA_SEG_ERROR, so this will go through 'case 0' and
 * effectively do nothing.
 */
static void wa_seg_dto_cb(struct urb *urb)
{
        struct wa_seg *seg = urb->context;
        struct wa_xfer *xfer = seg->xfer;
        struct wahc *wa;
        struct device *dev;
        struct wa_rpipe *rpipe;
        unsigned long flags;
        unsigned rpipe_ready = 0;
        int data_send_done = 1, release_dto = 0, holding_dto = 0;
        u8 done = 0;
        int result;

        /* free the sg if it was used. */
        kfree(urb->sg);
        urb->sg = NULL;

        spin_lock_irqsave(&xfer->lock, flags);
        wa = xfer->wa;
        dev = &wa->usb_iface->dev;
        if (usb_pipeisoc(xfer->urb->pipe)) {
                /* Alereon HWA sends all isoc frames in a single transfer. */
                if (wa->quirks & WUSB_QUIRK_ALEREON_HWA_CONCAT_ISOC)
                        seg->isoc_frame_index += seg->isoc_frame_count;
                else
                        seg->isoc_frame_index += 1;
                if (seg->isoc_frame_index < seg->isoc_frame_count) {
                        data_send_done = 0;
                        holding_dto = 1; /* checked in error cases. */
                        /*
                         * if this is the last isoc frame of the segment, we
                         * can release DTO after sending this frame.
                         */
                        if ((seg->isoc_frame_index + 1) >=
                                seg->isoc_frame_count)
                                release_dto = 1;
                }
                dev_dbg(dev, "xfer 0x%08X#%u: isoc frame = %d, holding_dto = %d, release_dto = %d.\n",
                        wa_xfer_id(xfer), seg->index, seg->isoc_frame_index,
                        holding_dto, release_dto);
        }
        spin_unlock_irqrestore(&xfer->lock, flags);

        switch (urb->status) {
        case 0:
                spin_lock_irqsave(&xfer->lock, flags);
                seg->result += urb->actual_length;
                if (data_send_done) {
                        dev_dbg(dev, "xfer 0x%08X#%u: data out done (%zu bytes)\n",
                                wa_xfer_id(xfer), seg->index, seg->result);
                        if (seg->status < WA_SEG_PENDING)
                                seg->status = WA_SEG_PENDING;
                } else {
                        /* should only hit this for isoc xfers. */
                        /*
                         * Populate the dto URB with the next isoc frame buffer,
                         * send the URB and release DTO if we no longer need it.
                         */
                         __wa_populate_dto_urb_isoc(xfer, seg,
                                seg->isoc_frame_offset + seg->isoc_frame_index);

                        /* resubmit the URB with the next isoc frame. */
                        /* take a ref on resubmit. */
                        wa_xfer_get(xfer);
                        result = usb_submit_urb(seg->dto_urb, GFP_ATOMIC);
                        if (result < 0) {
                                dev_err(dev, "xfer 0x%08X#%u: DTO submit failed: %d\n",
                                       wa_xfer_id(xfer), seg->index, result);
                                spin_unlock_irqrestore(&xfer->lock, flags);
                                goto error_dto_submit;
                        }
                }
                spin_unlock_irqrestore(&xfer->lock, flags);
                if (release_dto) {
                        __wa_dto_put(wa);
                        wa_check_for_delayed_rpipes(wa);
                }
                break;
        case -ECONNRESET:       /* URB unlinked; no need to do anything */
        case -ENOENT:           /* as it was done by the who unlinked us */
                if (holding_dto) {
                        __wa_dto_put(wa);
                        wa_check_for_delayed_rpipes(wa);
                }
                break;
        default:                /* Other errors ... */
                dev_err(dev, "xfer 0x%08X#%u: data out error %d\n",
                        wa_xfer_id(xfer), seg->index, urb->status);
                goto error_default;
        }

        /* taken when this URB was submitted. */
        wa_xfer_put(xfer);
        return;

error_dto_submit:
        /* taken on resubmit attempt. */
        wa_xfer_put(xfer);
error_default:
        spin_lock_irqsave(&xfer->lock, flags);
        rpipe = xfer->ep->hcpriv;
        if (edc_inc(&wa->nep_edc, EDC_MAX_ERRORS,
                    EDC_ERROR_TIMEFRAME)){
                dev_err(dev, "DTO: URB max acceptable errors exceeded, resetting device\n");
                wa_reset_all(wa);
        }
        if (seg->status != WA_SEG_ERROR) {
                seg->result = urb->status;
                __wa_xfer_abort(xfer);
                rpipe_ready = rpipe_avail_inc(rpipe);
                done = __wa_xfer_mark_seg_as_done(xfer, seg, WA_SEG_ERROR);
        }
        spin_unlock_irqrestore(&xfer->lock, flags);
        if (holding_dto) {
                __wa_dto_put(wa);
                wa_check_for_delayed_rpipes(wa);
        }
        if (done)
                wa_xfer_completion(xfer);
        if (rpipe_ready)
                wa_xfer_delayed_run(rpipe);
        /* taken when this URB was submitted. */
        wa_xfer_put(xfer);
}

/*
 * Callback for the isoc packet descriptor phase of the segment request
 *
 * Check wa_seg_tr_cb(); most comments also apply here because this
 * function does almost the same thing and they work closely
 * together.
 *
 * If the seg request has failed but this phase has succeeded,
 * wa_seg_tr_cb() has already failed the segment and moved the
 * status to WA_SEG_ERROR, so this will go through 'case 0' and
 * effectively do nothing.
 */
static void wa_seg_iso_pack_desc_cb(struct urb *urb)
{
        struct wa_seg *seg = urb->context;
        struct wa_xfer *xfer = seg->xfer;
        struct wahc *wa;
        struct device *dev;
        struct wa_rpipe *rpipe;
        unsigned long flags;
        unsigned rpipe_ready = 0;
        u8 done = 0;

        switch (urb->status) {
        case 0:
                spin_lock_irqsave(&xfer->lock, flags);
                wa = xfer->wa;
                dev = &wa->usb_iface->dev;
                dev_dbg(dev, "iso xfer %08X#%u: packet descriptor done\n",
                        wa_xfer_id(xfer), seg->index);
                if (xfer->is_inbound && seg->status < WA_SEG_PENDING)
                        seg->status = WA_SEG_PENDING;
                spin_unlock_irqrestore(&xfer->lock, flags);
                break;
        case -ECONNRESET:       /* URB unlinked; no need to do anything */
        case -ENOENT:           /* as it was done by the who unlinked us */
                break;
        default:                /* Other errors ... */
                spin_lock_irqsave(&xfer->lock, flags);
                wa = xfer->wa;
                dev = &wa->usb_iface->dev;
                rpipe = xfer->ep->hcpriv;
                pr_err_ratelimited("iso xfer %08X#%u: packet descriptor error %d\n",
                                wa_xfer_id(xfer), seg->index, urb->status);
                if (edc_inc(&wa->nep_edc, EDC_MAX_ERRORS,
                            EDC_ERROR_TIMEFRAME)){
                        dev_err(dev, "iso xfer: URB max acceptable errors exceeded, resetting device\n");
                        wa_reset_all(wa);
                }
                if (seg->status != WA_SEG_ERROR) {
                        usb_unlink_urb(seg->dto_urb);
                        seg->result = urb->status;
                        __wa_xfer_abort(xfer);
                        rpipe_ready = rpipe_avail_inc(rpipe);
                        done = __wa_xfer_mark_seg_as_done(xfer, seg,
                                        WA_SEG_ERROR);
                }
                spin_unlock_irqrestore(&xfer->lock, flags);
                if (done)
                        wa_xfer_completion(xfer);
                if (rpipe_ready)
                        wa_xfer_delayed_run(rpipe);
        }
        /* taken when this URB was submitted. */
        wa_xfer_put(xfer);
}

/*
 * Callback for the segment request
 *
 * If successful transition state (unless already transitioned or
 * outbound transfer); otherwise, take a note of the error, mark this
 * segment done and try completion.
 *
 * Note we don't access until we are sure that the transfer hasn't
 * been cancelled (ECONNRESET, ENOENT), which could mean that
 * seg->xfer could be already gone.
 *
 * We have to check before setting the status to WA_SEG_PENDING
 * because sometimes the xfer result callback arrives before this
 * callback (geeeeeeze), so it might happen that we are already in
 * another state. As well, we don't set it if the transfer is not inbound,
 * as in that case, wa_seg_dto_cb will do it when the OUT data phase
 * finishes.
 */
static void wa_seg_tr_cb(struct urb *urb)
{
        struct wa_seg *seg = urb->context;
        struct wa_xfer *xfer = seg->xfer;
        struct wahc *wa;
        struct device *dev;
        struct wa_rpipe *rpipe;
        unsigned long flags;
        unsigned rpipe_ready;
        u8 done = 0;

        switch (urb->status) {
        case 0:
                spin_lock_irqsave(&xfer->lock, flags);
                wa = xfer->wa;
                dev = &wa->usb_iface->dev;
                dev_dbg(dev, "xfer %p ID 0x%08X#%u: request done\n",
                        xfer, wa_xfer_id(xfer), seg->index);
                if (xfer->is_inbound &&
                        seg->status < WA_SEG_PENDING &&
                        !(usb_pipeisoc(xfer->urb->pipe)))
                        seg->status = WA_SEG_PENDING;
                spin_unlock_irqrestore(&xfer->lock, flags);
                break;
        case -ECONNRESET:       /* URB unlinked; no need to do anything */
        case -ENOENT:           /* as it was done by the who unlinked us */
                break;
        default:                /* Other errors ... */
                spin_lock_irqsave(&xfer->lock, flags);
                wa = xfer->wa;
                dev = &wa->usb_iface->dev;
                rpipe = xfer->ep->hcpriv;
                if (printk_ratelimit())
                        dev_err(dev, "xfer %p ID 0x%08X#%u: request error %d\n",
                                xfer, wa_xfer_id(xfer), seg->index,
                                urb->status);
                if (edc_inc(&wa->nep_edc, EDC_MAX_ERRORS,
                            EDC_ERROR_TIMEFRAME)){
                        dev_err(dev, "DTO: URB max acceptable errors "
                                "exceeded, resetting device\n");
                        wa_reset_all(wa);
                }
                usb_unlink_urb(seg->isoc_pack_desc_urb);
                usb_unlink_urb(seg->dto_urb);
                seg->result = urb->status;
                __wa_xfer_abort(xfer);
                rpipe_ready = rpipe_avail_inc(rpipe);
                done = __wa_xfer_mark_seg_as_done(xfer, seg, WA_SEG_ERROR);
                spin_unlock_irqrestore(&xfer->lock, flags);
                if (done)
                        wa_xfer_completion(xfer);
                if (rpipe_ready)
                        wa_xfer_delayed_run(rpipe);
        }
        /* taken when this URB was submitted. */
        wa_xfer_put(xfer);
}

/*
 * Allocate an SG list to store bytes_to_transfer bytes and copy the
 * subset of the in_sg that matches the buffer subset
 * we are about to transfer.
 */
static struct scatterlist *wa_xfer_create_subset_sg(struct scatterlist *in_sg,
        const unsigned int bytes_transferred,
        const unsigned int bytes_to_transfer, int *out_num_sgs)
{
        struct scatterlist *out_sg;
        unsigned int bytes_processed = 0, offset_into_current_page_data = 0,
                nents;
        struct scatterlist *current_xfer_sg = in_sg;
        struct scatterlist *current_seg_sg, *last_seg_sg;

        /* skip previously transferred pages. */
        while ((current_xfer_sg) &&
                        (bytes_processed < bytes_transferred)) {
                bytes_processed += current_xfer_sg->length;

                /* advance the sg if current segment starts on or past the
                        next page. */
                if (bytes_processed <= bytes_transferred)
                        current_xfer_sg = sg_next(current_xfer_sg);
        }

        /* the data for the current segment starts in current_xfer_sg.
                calculate the offset. */
        if (bytes_processed > bytes_transferred) {
                offset_into_current_page_data = current_xfer_sg->length -
                        (bytes_processed - bytes_transferred);
        }

        /* calculate the number of pages needed by this segment. */
        nents = DIV_ROUND_UP((bytes_to_transfer +
                offset_into_current_page_data +
                current_xfer_sg->offset),
                PAGE_SIZE);

        out_sg = kmalloc((sizeof(struct scatterlist) * nents), GFP_ATOMIC);
        if (out_sg) {
                sg_init_table(out_sg, nents);

                /* copy the portion of the incoming SG that correlates to the
                 * data to be transferred by this segment to the segment SG. */
                last_seg_sg = current_seg_sg = out_sg;
                bytes_processed = 0;

                /* reset nents and calculate the actual number of sg entries
                        needed. */
                nents = 0;
                while ((bytes_processed < bytes_to_transfer) &&
                                current_seg_sg && current_xfer_sg) {
                        unsigned int page_len = min((current_xfer_sg->length -
                                offset_into_current_page_data),
                                (bytes_to_transfer - bytes_processed));

                        sg_set_page(current_seg_sg, sg_page(current_xfer_sg),
                                page_len,
                                current_xfer_sg->offset +
                                offset_into_current_page_data);

                        bytes_processed += page_len;

                        last_seg_sg = current_seg_sg;
                        current_seg_sg = sg_next(current_seg_sg);
                        current_xfer_sg = sg_next(current_xfer_sg);

                        /* only the first page may require additional offset. */
                        offset_into_current_page_data = 0;
                        nents++;
                }

                /* update num_sgs and terminate the list since we may have
                 *  concatenated pages. */
                sg_mark_end(last_seg_sg);
                *out_num_sgs = nents;
        }

        return out_sg;
}

/*
 * Populate DMA buffer info for the isoc dto urb.
 */
static void __wa_populate_dto_urb_isoc(struct wa_xfer *xfer,
        struct wa_seg *seg, int curr_iso_frame)
{
        seg->dto_urb->transfer_flags |= URB_NO_TRANSFER_DMA_MAP;
        seg->dto_urb->sg = NULL;
        seg->dto_urb->num_sgs = 0;
        /* dto urb buffer address pulled from iso_frame_desc. */
        seg->dto_urb->transfer_dma = xfer->urb->transfer_dma +
                xfer->urb->iso_frame_desc[curr_iso_frame].offset;
        /* The Alereon HWA sends a single URB with all isoc segs. */
        if (xfer->wa->quirks & WUSB_QUIRK_ALEREON_HWA_CONCAT_ISOC)
                seg->dto_urb->transfer_buffer_length = seg->isoc_size;
        else
                seg->dto_urb->transfer_buffer_length =
                        xfer->urb->iso_frame_desc[curr_iso_frame].length;
}

/*
 * Populate buffer ptr and size, DMA buffer or SG list for the dto urb.
 */
static int __wa_populate_dto_urb(struct wa_xfer *xfer,
        struct wa_seg *seg, size_t buf_itr_offset, size_t buf_itr_size)
{
        int result = 0;

        if (xfer->is_dma) {
                seg->dto_urb->transfer_dma =
                        xfer->urb->transfer_dma + buf_itr_offset;
                seg->dto_urb->transfer_flags |= URB_NO_TRANSFER_DMA_MAP;
                seg->dto_urb->sg = NULL;
                seg->dto_urb->num_sgs = 0;
        } else {
                /* do buffer or SG processing. */
                seg->dto_urb->transfer_flags &=
                        ~URB_NO_TRANSFER_DMA_MAP;
                /* this should always be 0 before a resubmit. */
                seg->dto_urb->num_mapped_sgs = 0;

                if (xfer->urb->transfer_buffer) {
                        seg->dto_urb->transfer_buffer =
                                xfer->urb->transfer_buffer +
                                buf_itr_offset;
                        seg->dto_urb->sg = NULL;
                        seg->dto_urb->num_sgs = 0;
                } else {
                        seg->dto_urb->transfer_buffer = NULL;

                        /*
                         * allocate an SG list to store seg_size bytes
                         * and copy the subset of the xfer->urb->sg that
                         * matches the buffer subset we are about to
                         * read.
                         */
                        seg->dto_urb->sg = wa_xfer_create_subset_sg(
                                xfer->urb->sg,
                                buf_itr_offset, buf_itr_size,
                                &(seg->dto_urb->num_sgs));
                        if (!(seg->dto_urb->sg))
                                result = -ENOMEM;
                }
        }
        seg->dto_urb->transfer_buffer_length = buf_itr_size;

        return result;
}

/*
 * Allocate the segs array and initialize each of them
 *
 * The segments are freed by wa_xfer_destroy() when the xfer use count
 * drops to zero; however, because each segment is given the same life
 * cycle as the USB URB it contains, it is actually freed by
 * usb_put_urb() on the contained USB URB (twisted, eh?).
 */
static int __wa_xfer_setup_segs(struct wa_xfer *xfer, size_t xfer_hdr_size)
{
        int result, cnt, isoc_frame_offset = 0;
        size_t alloc_size = sizeof(*xfer->seg[0])
                - sizeof(xfer->seg[0]->xfer_hdr) + xfer_hdr_size;
        struct usb_device *usb_dev = xfer->wa->usb_dev;
        const struct usb_endpoint_descriptor *dto_epd = xfer->wa->dto_epd;
        struct wa_seg *seg;
        size_t buf_itr, buf_size, buf_itr_size;

        result = -ENOMEM;
        xfer->seg = kcalloc(xfer->segs, sizeof(xfer->seg[0]), GFP_ATOMIC);
        if (xfer->seg == NULL)
                goto error_segs_kzalloc;
        buf_itr = 0;
        buf_size = xfer->urb->transfer_buffer_length;
        for (cnt = 0; cnt < xfer->segs; cnt++) {
                size_t iso_pkt_descr_size = 0;
                int seg_isoc_frame_count = 0, seg_isoc_size = 0;

                /*
                 * Adjust the size of the segment object to contain space for
                 * the isoc packet descriptor buffer.
                 */
                if (usb_pipeisoc(xfer->urb->pipe)) {
                        seg_isoc_frame_count =
                                __wa_seg_calculate_isoc_frame_count(xfer,
                                        isoc_frame_offset, &seg_isoc_size);

                        iso_pkt_descr_size =
                                sizeof(struct wa_xfer_packet_info_hwaiso) +
                                (seg_isoc_frame_count * sizeof(__le16));
                }
                result = -ENOMEM;
                seg = xfer->seg[cnt] = kmalloc(alloc_size + iso_pkt_descr_size,
                                                GFP_ATOMIC);
                if (seg == NULL)
                        goto error_seg_kmalloc;
                wa_seg_init(seg);
                seg->xfer = xfer;
                seg->index = cnt;
                usb_fill_bulk_urb(&seg->tr_urb, usb_dev,
                                  usb_sndbulkpipe(usb_dev,
                                                  dto_epd->bEndpointAddress),
                                  &seg->xfer_hdr, xfer_hdr_size,
                                  wa_seg_tr_cb, seg);
                buf_itr_size = min(buf_size, xfer->seg_size);

                if (usb_pipeisoc(xfer->urb->pipe)) {
                        seg->isoc_frame_count = seg_isoc_frame_count;
                        seg->isoc_frame_offset = isoc_frame_offset;
                        seg->isoc_size = seg_isoc_size;
                        /* iso packet descriptor. */
                        seg->isoc_pack_desc_urb =
                                        usb_alloc_urb(0, GFP_ATOMIC);
                        if (seg->isoc_pack_desc_urb == NULL)
                                goto error_iso_pack_desc_alloc;
                        /*
                         * The buffer for the isoc packet descriptor starts
                         * after the transfer request header in the
                         * segment object memory buffer.
                         */
                        usb_fill_bulk_urb(
                                seg->isoc_pack_desc_urb, usb_dev,
                                usb_sndbulkpipe(usb_dev,
                                        dto_epd->bEndpointAddress),
                                (void *)(&seg->xfer_hdr) +
                                        xfer_hdr_size,
                                iso_pkt_descr_size,
                                wa_seg_iso_pack_desc_cb, seg);

                        /* adjust starting frame offset for next seg. */
                        isoc_frame_offset += seg_isoc_frame_count;
                }

                if (xfer->is_inbound == 0 && buf_size > 0) {
                        /* outbound data. */
                        seg->dto_urb = usb_alloc_urb(0, GFP_ATOMIC);
                        if (seg->dto_urb == NULL)
                                goto error_dto_alloc;
                        usb_fill_bulk_urb(
                                seg->dto_urb, usb_dev,
                                usb_sndbulkpipe(usb_dev,
                                                dto_epd->bEndpointAddress),
                                NULL, 0, wa_seg_dto_cb, seg);

                        if (usb_pipeisoc(xfer->urb->pipe)) {
                                /*
                                 * Fill in the xfer buffer information for the
                                 * first isoc frame.  Subsequent frames in this
                                 * segment will be filled in and sent from the
                                 * DTO completion routine, if needed.
                                 */
                                __wa_populate_dto_urb_isoc(xfer, seg,
                                        seg->isoc_frame_offset);
                        } else {
                                /* fill in the xfer buffer information. */
                                result = __wa_populate_dto_urb(xfer, seg,
                                                        buf_itr, buf_itr_size);
                                if (result < 0)
                                        goto error_seg_outbound_populate;

                                buf_itr += buf_itr_size;
                                buf_size -= buf_itr_size;
                        }
                }
                seg->status = WA_SEG_READY;
        }
        return 0;

        /*
         * Free the memory for the current segment which failed to init.
         * Use the fact that cnt is left at were it failed.  The remaining
         * segments will be cleaned up by wa_xfer_destroy.
         */
error_seg_outbound_populate:
        usb_free_urb(xfer->seg[cnt]->dto_urb);
error_dto_alloc:
        usb_free_urb(xfer->seg[cnt]->isoc_pack_desc_urb);
error_iso_pack_desc_alloc:
        kfree(xfer->seg[cnt]);
        xfer->seg[cnt] = NULL;
error_seg_kmalloc:
error_segs_kzalloc:
        return result;
}

/*
 * Allocates all the stuff needed to submit a transfer
 *
 * Breaks the whole data buffer in a list of segments, each one has a
 * structure allocated to it and linked in xfer->seg[index]
 *
 * FIXME: merge setup_segs() and the last part of this function, no
 *        need to do two for loops when we could run everything in a
 *        single one
 */
static int __wa_xfer_setup(struct wa_xfer *xfer, struct urb *urb)
{
        int result;
        struct device *dev = &xfer->wa->usb_iface->dev;
        enum wa_xfer_type xfer_type = 0; /* shut up GCC */
        size_t xfer_hdr_size, cnt, transfer_size;
        struct wa_xfer_hdr *xfer_hdr0, *xfer_hdr;

        result = __wa_xfer_setup_sizes(xfer, &xfer_type);
        if (result < 0)
                goto error_setup_sizes;
        xfer_hdr_size = result;
        result = __wa_xfer_setup_segs(xfer, xfer_hdr_size);
        if (result < 0) {
                dev_err(dev, "xfer %p: Failed to allocate %d segments: %d\n",
                        xfer, xfer->segs, result);
                goto error_setup_segs;
        }
        /* Fill the first header */
        xfer_hdr0 = &xfer->seg[0]->xfer_hdr;
        wa_xfer_id_init(xfer);
        __wa_xfer_setup_hdr0(xfer, xfer_hdr0, xfer_type, xfer_hdr_size);

        /* Fill remaining headers */
        xfer_hdr = xfer_hdr0;
        if (xfer_type == WA_XFER_TYPE_ISO) {
                xfer_hdr0->dwTransferLength =
                        cpu_to_le32(xfer->seg[0]->isoc_size);
                for (cnt = 1; cnt < xfer->segs; cnt++) {
                        struct wa_xfer_packet_info_hwaiso *packet_desc;
                        struct wa_seg *seg = xfer->seg[cnt];
                        struct wa_xfer_hwaiso *xfer_iso;

                        xfer_hdr = &seg->xfer_hdr;
                        xfer_iso = container_of(xfer_hdr,
                                                struct wa_xfer_hwaiso, hdr);
                        packet_desc = ((void *)xfer_hdr) + xfer_hdr_size;
                        /*
                         * Copy values from the 0th header. Segment specific
                         * values are set below.
                         */
                        memcpy(xfer_hdr, xfer_hdr0, xfer_hdr_size);
                        xfer_hdr->bTransferSegment = cnt;
                        xfer_hdr->dwTransferLength =
                                cpu_to_le32(seg->isoc_size);
                        xfer_iso->dwNumOfPackets =
                                        cpu_to_le32(seg->isoc_frame_count);
                        __wa_setup_isoc_packet_descr(packet_desc, xfer, seg);
                        seg->status = WA_SEG_READY;
                }
        } else {
                transfer_size = urb->transfer_buffer_length;
                xfer_hdr0->dwTransferLength = transfer_size > xfer->seg_size ?
                        cpu_to_le32(xfer->seg_size) :
                        cpu_to_le32(transfer_size);
                transfer_size -=  xfer->seg_size;
                for (cnt = 1; cnt < xfer->segs; cnt++) {
                        xfer_hdr = &xfer->seg[cnt]->xfer_hdr;
                        memcpy(xfer_hdr, xfer_hdr0, xfer_hdr_size);
                        xfer_hdr->bTransferSegment = cnt;
                        xfer_hdr->dwTransferLength =
                                transfer_size > xfer->seg_size ?
                                        cpu_to_le32(xfer->seg_size)
                                        : cpu_to_le32(transfer_size);
                        xfer->seg[cnt]->status = WA_SEG_READY;
                        transfer_size -=  xfer->seg_size;
                }
        }
        xfer_hdr->bTransferSegment |= 0x80;     /* this is the last segment */
        result = 0;
error_setup_segs:
error_setup_sizes:
        return result;
}

/*
 *
 *
 * rpipe->seg_lock is held!
 */
static int __wa_seg_submit(struct wa_rpipe *rpipe, struct wa_xfer *xfer,
                           struct wa_seg *seg, int *dto_done)
{
        int result;

        /* default to done unless we encounter a multi-frame isoc segment. */
        *dto_done = 1;

        /*
         * Take a ref for each segment urb so the xfer cannot disappear until
         * all of the callbacks run.
         */
        wa_xfer_get(xfer);
        /* submit the transfer request. */
        seg->status = WA_SEG_SUBMITTED;
        result = usb_submit_urb(&seg->tr_urb, GFP_ATOMIC);
        if (result < 0) {
                pr_err("%s: xfer %p#%u: REQ submit failed: %d\n",
                       __func__, xfer, seg->index, result);
                wa_xfer_put(xfer);
                goto error_tr_submit;
        }
        /* submit the isoc packet descriptor if present. */
        if (seg->isoc_pack_desc_urb) {
                wa_xfer_get(xfer);
                result = usb_submit_urb(seg->isoc_pack_desc_urb, GFP_ATOMIC);
                seg->isoc_frame_index = 0;
                if (result < 0) {
                        pr_err("%s: xfer %p#%u: ISO packet descriptor submit failed: %d\n",
                               __func__, xfer, seg->index, result);
                        wa_xfer_put(xfer);
                        goto error_iso_pack_desc_submit;
                }
        }
        /* submit the out data if this is an out request. */
        if (seg->dto_urb) {
                struct wahc *wa = xfer->wa;
                wa_xfer_get(xfer);
                result = usb_submit_urb(seg->dto_urb, GFP_ATOMIC);
                if (result < 0) {
                        pr_err("%s: xfer %p#%u: DTO submit failed: %d\n",
                               __func__, xfer, seg->index, result);
                        wa_xfer_put(xfer);
                        goto error_dto_submit;
                }
                /*
                 * If this segment contains more than one isoc frame, hold
                 * onto the dto resource until we send all frames.
                 * Only applies to non-Alereon devices.
                 */
                if (((wa->quirks & WUSB_QUIRK_ALEREON_HWA_CONCAT_ISOC) == 0)
                        && (seg->isoc_frame_count > 1))
                        *dto_done = 0;
        }
        rpipe_avail_dec(rpipe);
        return 0;

error_dto_submit:
        usb_unlink_urb(seg->isoc_pack_desc_urb);
error_iso_pack_desc_submit:
        usb_unlink_urb(&seg->tr_urb);
error_tr_submit:
        seg->status = WA_SEG_ERROR;
        seg->result = result;
        *dto_done = 1;
        return result;
}

/*
 * Execute more queued request segments until the maximum concurrent allowed.
 * Return true if the DTO resource was acquired and released.
 *
 * The ugly unlock/lock sequence on the error path is needed as the
 * xfer->lock normally nests the seg_lock and not viceversa.
 */
static int __wa_xfer_delayed_run(struct wa_rpipe *rpipe, int *dto_waiting)
{
        int result, dto_acquired = 0, dto_done = 0;
        struct device *dev = &rpipe->wa->usb_iface->dev;
        struct wa_seg *seg;
        struct wa_xfer *xfer;
        unsigned long flags;

        *dto_waiting = 0;

        spin_lock_irqsave(&rpipe->seg_lock, flags);
        while (atomic_read(&rpipe->segs_available) > 0
              && !list_empty(&rpipe->seg_list)
              && (dto_acquired = __wa_dto_try_get(rpipe->wa))) {
                seg = list_first_entry(&(rpipe->seg_list), struct wa_seg,
                                 list_node);
                list_del(&seg->list_node);
                xfer = seg->xfer;
                /*
                 * Get a reference to the xfer in case the callbacks for the
                 * URBs submitted by __wa_seg_submit attempt to complete
                 * the xfer before this function completes.
                 */
                wa_xfer_get(xfer);
                result = __wa_seg_submit(rpipe, xfer, seg, &dto_done);
                /* release the dto resource if this RPIPE is done with it. */
                if (dto_done)
                        __wa_dto_put(rpipe->wa);
                dev_dbg(dev, "xfer %p ID %08X#%u submitted from delayed [%d segments available] %d\n",
                        xfer, wa_xfer_id(xfer), seg->index,
                        atomic_read(&rpipe->segs_available), result);
                if (unlikely(result < 0)) {
                        int done;

                        spin_unlock_irqrestore(&rpipe->seg_lock, flags);
                        spin_lock_irqsave(&xfer->lock, flags);
                        __wa_xfer_abort(xfer);
                        /*
                         * This seg was marked as submitted when it was put on
                         * the RPIPE seg_list.  Mark it done.
                         */
                        xfer->segs_done++;
                        done = __wa_xfer_is_done(xfer);
                        spin_unlock_irqrestore(&xfer->lock, flags);
                        if (done)
                                wa_xfer_completion(xfer);
                        spin_lock_irqsave(&rpipe->seg_lock, flags);
                }
                wa_xfer_put(xfer);
        }
        /*
         * Mark this RPIPE as waiting if dto was not acquired, there are
         * delayed segs and no active transfers to wake us up later.
         */
        if (!dto_acquired && !list_empty(&rpipe->seg_list)
                && (atomic_read(&rpipe->segs_available) ==
                        le16_to_cpu(rpipe->descr.wRequests)))
                *dto_waiting = 1;

        spin_unlock_irqrestore(&rpipe->seg_lock, flags);

        return dto_done;
}

static void wa_xfer_delayed_run(struct wa_rpipe *rpipe)
{
        int dto_waiting;
        int dto_done = __wa_xfer_delayed_run(rpipe, &dto_waiting);

        /*
         * If this RPIPE is waiting on the DTO resource, add it to the tail of
         * the waiting list.
         * Otherwise, if the WA DTO resource was acquired and released by
         *  __wa_xfer_delayed_run, another RPIPE may have attempted to acquire
         * DTO and failed during that time.  Check the delayed list and process
         * any waiters.  Start searching from the next RPIPE index.
         */
        if (dto_waiting)
                wa_add_delayed_rpipe(rpipe->wa, rpipe);
        else if (dto_done)
                wa_check_for_delayed_rpipes(rpipe->wa);
}

/*
 *
 * xfer->lock is taken
 *
 * On failure submitting we just stop submitting and return error;
 * wa_urb_enqueue_b() will execute the completion path
 */
static int __wa_xfer_submit(struct wa_xfer *xfer)
{
        int result, dto_acquired = 0, dto_done = 0, dto_waiting = 0;
        struct wahc *wa = xfer->wa;
        struct device *dev = &wa->usb_iface->dev;
        unsigned cnt;
        struct wa_seg *seg;
        unsigned long flags;
        struct wa_rpipe *rpipe = xfer->ep->hcpriv;
        size_t maxrequests = le16_to_cpu(rpipe->descr.wRequests);
        u8 available;
        u8 empty;

        spin_lock_irqsave(&wa->xfer_list_lock, flags);
        list_add_tail(&xfer->list_node, &wa->xfer_list);
        spin_unlock_irqrestore(&wa->xfer_list_lock, flags);

        BUG_ON(atomic_read(&rpipe->segs_available) > maxrequests);
        result = 0;
        spin_lock_irqsave(&rpipe->seg_lock, flags);
        for (cnt = 0; cnt < xfer->segs; cnt++) {
                int delay_seg = 1;

                available = atomic_read(&rpipe->segs_available);
                empty = list_empty(&rpipe->seg_list);
                seg = xfer->seg[cnt];
                if (available && empty) {
                        /*
                         * Only attempt to acquire DTO if we have a segment
                         * to send.
                         */
                        dto_acquired = __wa_dto_try_get(rpipe->wa);
                        if (dto_acquired) {
                                delay_seg = 0;
                                result = __wa_seg_submit(rpipe, xfer, seg,
                                                        &dto_done);
                                dev_dbg(dev, "xfer %p ID 0x%08X#%u: available %u empty %u submitted\n",
                                        xfer, wa_xfer_id(xfer), cnt, available,
                                        empty);
                                if (dto_done)
                                        __wa_dto_put(rpipe->wa);

                                if (result < 0) {
                                        __wa_xfer_abort(xfer);
                                        goto error_seg_submit;
                                }
                        }
                }

                if (delay_seg) {
                        dev_dbg(dev, "xfer %p ID 0x%08X#%u: available %u empty %u delayed\n",
                                xfer, wa_xfer_id(xfer), cnt, available,  empty);
                        seg->status = WA_SEG_DELAYED;
                        list_add_tail(&seg->list_node, &rpipe->seg_list);
                }
                xfer->segs_submitted++;
        }
error_seg_submit:
        /*
         * Mark this RPIPE as waiting if dto was not acquired, there are
         * delayed segs and no active transfers to wake us up later.
         */
        if (!dto_acquired && !list_empty(&rpipe->seg_list)
                && (atomic_read(&rpipe->segs_available) ==
                        le16_to_cpu(rpipe->descr.wRequests)))
                dto_waiting = 1;
        spin_unlock_irqrestore(&rpipe->seg_lock, flags);

        if (dto_waiting)
                wa_add_delayed_rpipe(rpipe->wa, rpipe);
        else if (dto_done)
                wa_check_for_delayed_rpipes(rpipe->wa);

        return result;
}

/*
 * Second part of a URB/transfer enqueuement
 *
 * Assumes this comes from wa_urb_enqueue() [maybe through
 * wa_urb_enqueue_run()]. At this point:
 *
 * xfer->wa     filled and refcounted
 * xfer->ep     filled with rpipe refcounted if
 *              delayed == 0
 * xfer->urb    filled and refcounted (this is the case when called
 *              from wa_urb_enqueue() as we come from usb_submit_urb()
 *              and when called by wa_urb_enqueue_run(), as we took an
 *              extra ref dropped by _run() after we return).
 * xfer->gfp    filled
 *
 * If we fail at __wa_xfer_submit(), then we just check if we are done
 * and if so, we run the completion procedure. However, if we are not
 * yet done, we do nothing and wait for the completion handlers from
 * the submitted URBs or from the xfer-result path to kick in. If xfer
 * result never kicks in, the xfer will timeout from the USB code and
 * dequeue() will be called.
 */
static int wa_urb_enqueue_b(struct wa_xfer *xfer)
{
        int result;
        unsigned long flags;
        struct urb *urb = xfer->urb;
        struct wahc *wa = xfer->wa;
        struct wusbhc *wusbhc = wa->wusb;
        struct wusb_dev *wusb_dev;
        unsigned done;

        result = rpipe_get_by_ep(wa, xfer->ep, urb, xfer->gfp);
        if (result < 0) {
                pr_err("%s: error_rpipe_get\n", __func__);
                goto error_rpipe_get;
        }
        result = -ENODEV;
        /* FIXME: segmentation broken -- kills DWA */
        mutex_lock(&wusbhc->mutex);             /* get a WUSB dev */
        if (urb->dev == NULL) {
                mutex_unlock(&wusbhc->mutex);
                pr_err("%s: error usb dev gone\n", __func__);
                goto error_dev_gone;
        }
        wusb_dev = __wusb_dev_get_by_usb_dev(wusbhc, urb->dev);
        if (wusb_dev == NULL) {
                mutex_unlock(&wusbhc->mutex);
                dev_err(&(urb->dev->dev), "%s: error wusb dev gone\n",
                        __func__);
                goto error_dev_gone;
        }
        mutex_unlock(&wusbhc->mutex);

        spin_lock_irqsave(&xfer->lock, flags);
        xfer->wusb_dev = wusb_dev;
        result = urb->status;
        if (urb->status != -EINPROGRESS) {
                dev_err(&(urb->dev->dev), "%s: error_dequeued\n", __func__);
                goto error_dequeued;
        }

        result = __wa_xfer_setup(xfer, urb);
        if (result < 0) {
                dev_err(&(urb->dev->dev), "%s: error_xfer_setup\n", __func__);
                goto error_xfer_setup;
        }
        /*
         * Get a xfer reference since __wa_xfer_submit starts asynchronous
         * operations that may try to complete the xfer before this function
         * exits.
         */
        wa_xfer_get(xfer);
        result = __wa_xfer_submit(xfer);
        if (result < 0) {
                dev_err(&(urb->dev->dev), "%s: error_xfer_submit\n", __func__);
                goto error_xfer_submit;
        }
        spin_unlock_irqrestore(&xfer->lock, flags);
        wa_xfer_put(xfer);
        return 0;

        /*
         * this is basically wa_xfer_completion() broken up wa_xfer_giveback()
         * does a wa_xfer_put() that will call wa_xfer_destroy() and undo
         * setup().
         */
error_xfer_setup:
error_dequeued:
        spin_unlock_irqrestore(&xfer->lock, flags);
        /* FIXME: segmentation broken, kills DWA */
        if (wusb_dev)
                wusb_dev_put(wusb_dev);
error_dev_gone:
        rpipe_put(xfer->ep->hcpriv);
error_rpipe_get:
        xfer->result = result;
        return result;

error_xfer_submit:
        done = __wa_xfer_is_done(xfer);
        xfer->result = result;
        spin_unlock_irqrestore(&xfer->lock, flags);
        if (done)
                wa_xfer_completion(xfer);
        wa_xfer_put(xfer);
        /* return success since the completion routine will run. */
        return 0;
}

/*
 * Execute the delayed transfers in the Wire Adapter @wa
 *
 * We need to be careful here, as dequeue() could be called in the
 * middle.  That's why we do the whole thing under the
 * wa->xfer_list_lock. If dequeue() jumps in, it first locks xfer->lock
 * and then checks the list -- so as we would be acquiring in inverse
 * order, we move the delayed list to a separate list while locked and then
 * submit them without the list lock held.
 */
void wa_urb_enqueue_run(struct work_struct *ws)
{
        struct wahc *wa = container_of(ws, struct wahc, xfer_enqueue_work);
        struct wa_xfer *xfer, *next;
        struct urb *urb;
        LIST_HEAD(tmp_list);

        /* Create a copy of the wa->xfer_delayed_list while holding the lock */
        spin_lock_irq(&wa->xfer_list_lock);
        list_cut_position(&tmp_list, &wa->xfer_delayed_list,
                        wa->xfer_delayed_list.prev);
        spin_unlock_irq(&wa->xfer_list_lock);

        /*
         * enqueue from temp list without list lock held since wa_urb_enqueue_b
         * can take xfer->lock as well as lock mutexes.
         */
        list_for_each_entry_safe(xfer, next, &tmp_list, list_node) {
                list_del_init(&xfer->list_node);

                urb = xfer->urb;
                if (wa_urb_enqueue_b(xfer) < 0)
                        wa_xfer_giveback(xfer);
                usb_put_urb(urb);       /* taken when queuing */
        }
}
EXPORT_SYMBOL_GPL(wa_urb_enqueue_run);

/*
 * Process the errored transfers on the Wire Adapter outside of interrupt.
 */
void wa_process_errored_transfers_run(struct work_struct *ws)
{
        struct wahc *wa = container_of(ws, struct wahc, xfer_error_work);
        struct wa_xfer *xfer, *next;
        LIST_HEAD(tmp_list);

        pr_info("%s: Run delayed STALL processing.\n", __func__);

        /* Create a copy of the wa->xfer_errored_list while holding the lock */
        spin_lock_irq(&wa->xfer_list_lock);
        list_cut_position(&tmp_list, &wa->xfer_errored_list,
                        wa->xfer_errored_list.prev);
        spin_unlock_irq(&wa->xfer_list_lock);

        /*
         * run rpipe_clear_feature_stalled from temp list without list lock
         * held.
         */
        list_for_each_entry_safe(xfer, next, &tmp_list, list_node) {
                struct usb_host_endpoint *ep;
                unsigned long flags;
                struct wa_rpipe *rpipe;

                spin_lock_irqsave(&xfer->lock, flags);
                ep = xfer->ep;
                rpipe = ep->hcpriv;
                spin_unlock_irqrestore(&xfer->lock, flags);

                /* clear RPIPE feature stalled without holding a lock. */
                rpipe_clear_feature_stalled(wa, ep);

                /* complete the xfer. This removes it from the tmp list. */
                wa_xfer_completion(xfer);

                /* check for work. */
                wa_xfer_delayed_run(rpipe);
        }
}
EXPORT_SYMBOL_GPL(wa_process_errored_transfers_run);

/*
 * Submit a transfer to the Wire Adapter in a delayed way
 *
 * The process of enqueuing involves possible sleeps() [see
 * enqueue_b(), for the rpipe_get() and the mutex_lock()]. If we are
 * in an atomic section, we defer the enqueue_b() call--else we call direct.
 *
 * @urb: We own a reference to it done by the HCI Linux USB stack that
 *       will be given up by calling usb_hcd_giveback_urb() or by
 *       returning error from this function -> ergo we don't have to
 *       refcount it.
 */
int wa_urb_enqueue(struct wahc *wa, struct usb_host_endpoint *ep,
                   struct urb *urb, gfp_t gfp)
{
        int result;
        struct device *dev = &wa->usb_iface->dev;
        struct wa_xfer *xfer;
        unsigned long my_flags;
        unsigned cant_sleep = irqs_disabled() | in_atomic();

        if ((urb->transfer_buffer == NULL)
            && (urb->sg == NULL)
            && !(urb->transfer_flags & URB_NO_TRANSFER_DMA_MAP)
            && urb->transfer_buffer_length != 0) {
                dev_err(dev, "BUG? urb %p: NULL xfer buffer & NODMA\n", urb);
                dump_stack();
        }

        spin_lock_irqsave(&wa->xfer_list_lock, my_flags);
        result = usb_hcd_link_urb_to_ep(&(wa->wusb->usb_hcd), urb);
        spin_unlock_irqrestore(&wa->xfer_list_lock, my_flags);
        if (result < 0)
                goto error_link_urb;

        result = -ENOMEM;
        xfer = kzalloc(sizeof(*xfer), gfp);
        if (xfer == NULL)
                goto error_kmalloc;

        result = -ENOENT;
        if (urb->status != -EINPROGRESS)        /* cancelled */
                goto error_dequeued;            /* before starting? */
        wa_xfer_init(xfer);
        xfer->wa = wa_get(wa);
        xfer->urb = urb;
        xfer->gfp = gfp;
        xfer->ep = ep;
        urb->hcpriv = xfer;

        dev_dbg(dev, "xfer %p urb %p pipe 0x%02x [%d bytes] %s %s %s\n",
                xfer, urb, urb->pipe, urb->transfer_buffer_length,
                urb->transfer_flags & URB_NO_TRANSFER_DMA_MAP ? "dma" : "nodma",
                urb->pipe & USB_DIR_IN ? "inbound" : "outbound",
                cant_sleep ? "deferred" : "inline");

        if (cant_sleep) {
                usb_get_urb(urb);
                spin_lock_irqsave(&wa->xfer_list_lock, my_flags);
                list_add_tail(&xfer->list_node, &wa->xfer_delayed_list);
                spin_unlock_irqrestore(&wa->xfer_list_lock, my_flags);
                queue_work(wusbd, &wa->xfer_enqueue_work);
        } else {
                result = wa_urb_enqueue_b(xfer);
                if (result < 0) {
                        /*
                         * URB submit/enqueue failed.  Clean up, return an
                         * error and do not run the callback.  This avoids
                         * an infinite submit/complete loop.
                         */
                        dev_err(dev, "%s: URB enqueue failed: %d\n",
                           __func__, result);
                        wa_put(xfer->wa);
                        wa_xfer_put(xfer);
                        spin_lock_irqsave(&wa->xfer_list_lock, my_flags);
                        usb_hcd_unlink_urb_from_ep(&(wa->wusb->usb_hcd), urb);
                        spin_unlock_irqrestore(&wa->xfer_list_lock, my_flags);
                        return result;
                }
        }
        return 0;

error_dequeued:
        kfree(xfer);
error_kmalloc:
        spin_lock_irqsave(&wa->xfer_list_lock, my_flags);
        usb_hcd_unlink_urb_from_ep(&(wa->wusb->usb_hcd), urb);
        spin_unlock_irqrestore(&wa->xfer_list_lock, my_flags);
error_link_urb:
        return result;
}
EXPORT_SYMBOL_GPL(wa_urb_enqueue);

/*
 * Dequeue a URB and make sure uwb_hcd_giveback_urb() [completion
 * handler] is called.
 *
 * Until a transfer goes successfully through wa_urb_enqueue() it
 * needs to be dequeued with completion calling; when stuck in delayed
 * or before wa_xfer_setup() is called, we need to do completion.
 *
 *  not setup  If there is no hcpriv yet, that means that that enqueue
 *             still had no time to set the xfer up. Because
 *             urb->status should be other than -EINPROGRESS,
 *             enqueue() will catch that and bail out.
 *
 * If the transfer has gone through setup, we just need to clean it
 * up. If it has gone through submit(), we have to abort it [with an
 * asynch request] and then make sure we cancel each segment.
 *
 */
int wa_urb_dequeue(struct wahc *wa, struct urb *urb, int status)
{
        unsigned long flags;
        struct wa_xfer *xfer;
        struct wa_seg *seg;
        struct wa_rpipe *rpipe;
        unsigned cnt, done = 0, xfer_abort_pending;
        unsigned rpipe_ready = 0;
        int result;

        /* check if it is safe to unlink. */
        spin_lock_irqsave(&wa->xfer_list_lock, flags);
        result = usb_hcd_check_unlink_urb(&(wa->wusb->usb_hcd), urb, status);
        if ((result == 0) && urb->hcpriv) {
                /*
                 * Get a xfer ref to prevent a race with wa_xfer_giveback
                 * cleaning up the xfer while we are working with it.
                 */
                wa_xfer_get(urb->hcpriv);
        }
        spin_unlock_irqrestore(&wa->xfer_list_lock, flags);
        if (result)
                return result;

        xfer = urb->hcpriv;
        if (xfer == NULL)
                return -ENOENT;
        spin_lock_irqsave(&xfer->lock, flags);
        pr_debug("%s: DEQUEUE xfer id 0x%08X\n", __func__, wa_xfer_id(xfer));
        rpipe = xfer->ep->hcpriv;
        if (rpipe == NULL) {
                pr_debug("%s: xfer %p id 0x%08X has no RPIPE.  %s",
                        __func__, xfer, wa_xfer_id(xfer),
                        "Probably already aborted.\n" );
                result = -ENOENT;
                goto out_unlock;
        }
        /*
         * Check for done to avoid racing with wa_xfer_giveback and completing
         * twice.
         */
        if (__wa_xfer_is_done(xfer)) {
                pr_debug("%s: xfer %p id 0x%08X already done.\n", __func__,
                        xfer, wa_xfer_id(xfer));
                result = -ENOENT;
                goto out_unlock;
        }
        /* Check the delayed list -> if there, release and complete */
        spin_lock(&wa->xfer_list_lock);
        if (!list_empty(&xfer->list_node) && xfer->seg == NULL)
                goto dequeue_delayed;
        spin_unlock(&wa->xfer_list_lock);
        if (xfer->seg == NULL)          /* still hasn't reached */
                goto out_unlock;        /* setup(), enqueue_b() completes */
        /* Ok, the xfer is in flight already, it's been setup and submitted.*/
        xfer_abort_pending = __wa_xfer_abort(xfer) >= 0;
        /*
         * grab the rpipe->seg_lock here to prevent racing with
         * __wa_xfer_delayed_run.
         */
        spin_lock(&rpipe->seg_lock);
        for (cnt = 0; cnt < xfer->segs; cnt++) {
                seg = xfer->seg[cnt];
                pr_debug("%s: xfer id 0x%08X#%d status = %d\n",
                        __func__, wa_xfer_id(xfer), cnt, seg->status);
                switch (seg->status) {
                case WA_SEG_NOTREADY:
                case WA_SEG_READY:
                        printk(KERN_ERR "xfer %p#%u: dequeue bad state %u\n",
                               xfer, cnt, seg->status);
                        WARN_ON(1);
                        break;
                case WA_SEG_DELAYED:
                        /*
                         * delete from rpipe delayed list.  If no segments on
                         * this xfer have been submitted, __wa_xfer_is_done will
                         * trigger a giveback below.  Otherwise, the submitted
                         * segments will be completed in the DTI interrupt.
                         */
                        seg->status = WA_SEG_ABORTED;
                        seg->result = -ENOENT;
                        list_del(&seg->list_node);
                        xfer->segs_done++;
                        break;
                case WA_SEG_DONE:
                case WA_SEG_ERROR:
                case WA_SEG_ABORTED:
                        break;
                        /*
                         * The buf_in data for a segment in the
                         * WA_SEG_DTI_PENDING state is actively being read.
                         * Let wa_buf_in_cb handle it since it will be called
                         * and will increment xfer->segs_done.  Cleaning up
                         * here could cause wa_buf_in_cb to access the xfer
                         * after it has been completed/freed.
                         */
                case WA_SEG_DTI_PENDING:
                        break;
                        /*
                         * In the states below, the HWA device already knows
                         * about the transfer.  If an abort request was sent,
                         * allow the HWA to process it and wait for the
                         * results.  Otherwise, the DTI state and seg completed
                         * counts can get out of sync.
                         */
                case WA_SEG_SUBMITTED:
                case WA_SEG_PENDING:
                        /*
                         * Check if the abort was successfully sent.  This could
                         * be false if the HWA has been removed but we haven't
                         * gotten the disconnect notification yet.
                         */
                        if (!xfer_abort_pending) {
                                seg->status = WA_SEG_ABORTED;
                                rpipe_ready = rpipe_avail_inc(rpipe);
                                xfer->segs_done++;
                        }
                        break;
                }
        }
        spin_unlock(&rpipe->seg_lock);
        xfer->result = urb->status;     /* -ENOENT or -ECONNRESET */
        done = __wa_xfer_is_done(xfer);
        spin_unlock_irqrestore(&xfer->lock, flags);
        if (done)
                wa_xfer_completion(xfer);
        if (rpipe_ready)
                wa_xfer_delayed_run(rpipe);
        wa_xfer_put(xfer);
        return result;

out_unlock:
        spin_unlock_irqrestore(&xfer->lock, flags);
        wa_xfer_put(xfer);
        return result;

dequeue_delayed:
        list_del_init(&xfer->list_node);
        spin_unlock(&wa->xfer_list_lock);
        xfer->result = urb->status;
        spin_unlock_irqrestore(&xfer->lock, flags);
        wa_xfer_giveback(xfer);
        wa_xfer_put(xfer);
        usb_put_urb(urb);               /* we got a ref in enqueue() */
        return 0;
}
EXPORT_SYMBOL_GPL(wa_urb_dequeue);

/*
 * Translation from WA status codes (WUSB1.0 Table 8.15) to errno
 * codes
 *
 * Positive errno values are internal inconsistencies and should be
 * flagged louder. Negative are to be passed up to the user in the
 * normal way.
 *
 * @status: USB WA status code -- high two bits are stripped.
 */
static int wa_xfer_status_to_errno(u8 status)
{
        int errno;
        u8 real_status = status;
        static int xlat[] = {
                [WA_XFER_STATUS_SUCCESS] =              0,
                [WA_XFER_STATUS_HALTED] =               -EPIPE,
                [WA_XFER_STATUS_DATA_BUFFER_ERROR] =    -ENOBUFS,
                [WA_XFER_STATUS_BABBLE] =               -EOVERFLOW,
                [WA_XFER_RESERVED] =                    EINVAL,
                [WA_XFER_STATUS_NOT_FOUND] =            0,
                [WA_XFER_STATUS_INSUFFICIENT_RESOURCE] = -ENOMEM,
                [WA_XFER_STATUS_TRANSACTION_ERROR] =    -EILSEQ,
                [WA_XFER_STATUS_ABORTED] =              -ENOENT,
                [WA_XFER_STATUS_RPIPE_NOT_READY] =      EINVAL,
                [WA_XFER_INVALID_FORMAT] =              EINVAL,
                [WA_XFER_UNEXPECTED_SEGMENT_NUMBER] =   EINVAL,
                [WA_XFER_STATUS_RPIPE_TYPE_MISMATCH] =  EINVAL,
        };
        status &= 0x3f;

        if (status == 0)
                return 0;
        if (status >= ARRAY_SIZE(xlat)) {
                printk_ratelimited(KERN_ERR "%s(): BUG? "
                               "Unknown WA transfer status 0x%02x\n",
                               __func__, real_status);
                return -EINVAL;
        }
        errno = xlat[status];
        if (unlikely(errno > 0)) {
                printk_ratelimited(KERN_ERR "%s(): BUG? "
                               "Inconsistent WA status: 0x%02x\n",
                               __func__, real_status);
                errno = -errno;
        }
        return errno;
}

/*
 * If a last segment flag and/or a transfer result error is encountered,
 * no other segment transfer results will be returned from the device.
 * Mark the remaining submitted or pending xfers as completed so that
 * the xfer will complete cleanly.
 *
 * xfer->lock must be held
 *
 */
static void wa_complete_remaining_xfer_segs(struct wa_xfer *xfer,
                int starting_index, enum wa_seg_status status)
{
        int index;
        struct wa_rpipe *rpipe = xfer->ep->hcpriv;

        for (index = starting_index; index < xfer->segs_submitted; index++) {
                struct wa_seg *current_seg = xfer->seg[index];

                BUG_ON(current_seg == NULL);

                switch (current_seg->status) {
                case WA_SEG_SUBMITTED:
                case WA_SEG_PENDING:
                case WA_SEG_DTI_PENDING:
                        rpipe_avail_inc(rpipe);
                /*
                 * do not increment RPIPE avail for the WA_SEG_DELAYED case
                 * since it has not been submitted to the RPIPE.
                 */
                /* fall through */
                case WA_SEG_DELAYED:
                        xfer->segs_done++;
                        current_seg->status = status;
                        break;
                case WA_SEG_ABORTED:
                        break;
                default:
                        WARN(1, "%s: xfer 0x%08X#%d. bad seg status = %d\n",
                                __func__, wa_xfer_id(xfer), index,
                                current_seg->status);
                        break;
                }
        }
}

/* Populate the given urb based on the current isoc transfer state. */
static int __wa_populate_buf_in_urb_isoc(struct wahc *wa,
        struct urb *buf_in_urb, struct wa_xfer *xfer, struct wa_seg *seg)
{
        int urb_start_frame = seg->isoc_frame_index + seg->isoc_frame_offset;
        int seg_index, total_len = 0, urb_frame_index = urb_start_frame;
        struct usb_iso_packet_descriptor *iso_frame_desc =
                                                xfer->urb->iso_frame_desc;
        const int dti_packet_size = usb_endpoint_maxp(wa->dti_epd);
        int next_frame_contiguous;
        struct usb_iso_packet_descriptor *iso_frame;

        BUG_ON(buf_in_urb->status == -EINPROGRESS);

        /*
         * If the current frame actual_length is contiguous with the next frame
         * and actual_length is a multiple of the DTI endpoint max packet size,
         * combine the current frame with the next frame in a single URB.  This
         * reduces the number of URBs that must be submitted in that case.
         */
        seg_index = seg->isoc_frame_index;
        do {
                next_frame_contiguous = 0;

                iso_frame = &iso_frame_desc[urb_frame_index];
                total_len += iso_frame->actual_length;
                ++urb_frame_index;
                ++seg_index;

                if (seg_index < seg->isoc_frame_count) {
                        struct usb_iso_packet_descriptor *next_iso_frame;

                        next_iso_frame = &iso_frame_desc[urb_frame_index];

                        if ((iso_frame->offset + iso_frame->actual_length) ==
                                next_iso_frame->offset)
                                next_frame_contiguous = 1;
                }
        } while (next_frame_contiguous
                        && ((iso_frame->actual_length % dti_packet_size) == 0));

        /* this should always be 0 before a resubmit. */
        buf_in_urb->num_mapped_sgs      = 0;
        buf_in_urb->transfer_dma = xfer->urb->transfer_dma +
                iso_frame_desc[urb_start_frame].offset;
        buf_in_urb->transfer_buffer_length = total_len;
        buf_in_urb->transfer_flags |= URB_NO_TRANSFER_DMA_MAP;
        buf_in_urb->transfer_buffer = NULL;
        buf_in_urb->sg = NULL;
        buf_in_urb->num_sgs = 0;
        buf_in_urb->context = seg;

        /* return the number of frames included in this URB. */
        return seg_index - seg->isoc_frame_index;
}

/* Populate the given urb based on the current transfer state. */
static int wa_populate_buf_in_urb(struct urb *buf_in_urb, struct wa_xfer *xfer,
        unsigned int seg_idx, unsigned int bytes_transferred)
{
        int result = 0;
        struct wa_seg *seg = xfer->seg[seg_idx];

        BUG_ON(buf_in_urb->status == -EINPROGRESS);
        /* this should always be 0 before a resubmit. */
        buf_in_urb->num_mapped_sgs      = 0;

        if (xfer->is_dma) {
                buf_in_urb->transfer_dma = xfer->urb->transfer_dma
                        + (seg_idx * xfer->seg_size);
                buf_in_urb->transfer_flags |= URB_NO_TRANSFER_DMA_MAP;
                buf_in_urb->transfer_buffer = NULL;
                buf_in_urb->sg = NULL;
                buf_in_urb->num_sgs = 0;
        } else {
                /* do buffer or SG processing. */
                buf_in_urb->transfer_flags &= ~URB_NO_TRANSFER_DMA_MAP;

                if (xfer->urb->transfer_buffer) {
                        buf_in_urb->transfer_buffer =
                                xfer->urb->transfer_buffer
                                + (seg_idx * xfer->seg_size);
                        buf_in_urb->sg = NULL;
                        buf_in_urb->num_sgs = 0;
                } else {
                        /* allocate an SG list to store seg_size bytes
                                and copy the subset of the xfer->urb->sg
                                that matches the buffer subset we are
                                about to read. */
                        buf_in_urb->sg = wa_xfer_create_subset_sg(
                                xfer->urb->sg,
                                seg_idx * xfer->seg_size,
                                bytes_transferred,
                                &(buf_in_urb->num_sgs));

                        if (!(buf_in_urb->sg)) {
                                buf_in_urb->num_sgs     = 0;
                                result = -ENOMEM;
                        }
                        buf_in_urb->transfer_buffer = NULL;
                }
        }
        buf_in_urb->transfer_buffer_length = bytes_transferred;
        buf_in_urb->context = seg;

        return result;
}

/*
 * Process a xfer result completion message
 *
 * inbound transfers: need to schedule a buf_in_urb read
 *
 * FIXME: this function needs to be broken up in parts
 */
static void wa_xfer_result_chew(struct wahc *wa, struct wa_xfer *xfer,
                struct wa_xfer_result *xfer_result)
{
        int result;
        struct device *dev = &wa->usb_iface->dev;
        unsigned long flags;
        unsigned int seg_idx;
        struct wa_seg *seg;
        struct wa_rpipe *rpipe;
        unsigned done = 0;
        u8 usb_status;
        unsigned rpipe_ready = 0;
        unsigned bytes_transferred = le32_to_cpu(xfer_result->dwTransferLength);
        struct urb *buf_in_urb = &(wa->buf_in_urbs[0]);

        spin_lock_irqsave(&xfer->lock, flags);
        seg_idx = xfer_result->bTransferSegment & 0x7f;
        if (unlikely(seg_idx >= xfer->segs))
                goto error_bad_seg;
        seg = xfer->seg[seg_idx];
        rpipe = xfer->ep->hcpriv;
        usb_status = xfer_result->bTransferStatus;
        dev_dbg(dev, "xfer %p ID 0x%08X#%u: bTransferStatus 0x%02x (seg status %u)\n",
                xfer, wa_xfer_id(xfer), seg_idx, usb_status, seg->status);
        if (seg->status == WA_SEG_ABORTED
            || seg->status == WA_SEG_ERROR)     /* already handled */
                goto segment_aborted;
        if (seg->status == WA_SEG_SUBMITTED)    /* ops, got here */
                seg->status = WA_SEG_PENDING;   /* before wa_seg{_dto}_cb() */
        if (seg->status != WA_SEG_PENDING) {
                if (printk_ratelimit())
                        dev_err(dev, "xfer %p#%u: Bad segment state %u\n",
                                xfer, seg_idx, seg->status);
                seg->status = WA_SEG_PENDING;   /* workaround/"fix" it */
        }
        if (usb_status & 0x80) {
                seg->result = wa_xfer_status_to_errno(usb_status);
                dev_err(dev, "DTI: xfer %p 0x%08X:#%u failed (0x%02x)\n",
                        xfer, xfer->id, seg->index, usb_status);
                seg->status = ((usb_status & 0x7F) == WA_XFER_STATUS_ABORTED) ?
                        WA_SEG_ABORTED : WA_SEG_ERROR;
                goto error_complete;
        }
        /* FIXME: we ignore warnings, tally them for stats */
        if (usb_status & 0x40)          /* Warning?... */
                usb_status = 0;         /* ... pass */
        /*
         * If the last segment bit is set, complete the remaining segments.
         * When the current segment is completed, either in wa_buf_in_cb for
         * transfers with data or below for no data, the xfer will complete.
         */
        if (xfer_result->bTransferSegment & 0x80)
                wa_complete_remaining_xfer_segs(xfer, seg->index + 1,
                        WA_SEG_DONE);
        if (usb_pipeisoc(xfer->urb->pipe)
                && (le32_to_cpu(xfer_result->dwNumOfPackets) > 0)) {
                /* set up WA state to read the isoc packet status next. */
                wa->dti_isoc_xfer_in_progress = wa_xfer_id(xfer);
                wa->dti_isoc_xfer_seg = seg_idx;
                wa->dti_state = WA_DTI_ISOC_PACKET_STATUS_PENDING;
        } else if (xfer->is_inbound && !usb_pipeisoc(xfer->urb->pipe)
                        && (bytes_transferred > 0)) {
                /* IN data phase: read to buffer */
                seg->status = WA_SEG_DTI_PENDING;
                result = wa_populate_buf_in_urb(buf_in_urb, xfer, seg_idx,
                        bytes_transferred);
                if (result < 0)
                        goto error_buf_in_populate;
                ++(wa->active_buf_in_urbs);
                result = usb_submit_urb(buf_in_urb, GFP_ATOMIC);
                if (result < 0) {
                        --(wa->active_buf_in_urbs);
                        goto error_submit_buf_in;
                }
        } else {
                /* OUT data phase or no data, complete it -- */
                seg->result = bytes_transferred;
                rpipe_ready = rpipe_avail_inc(rpipe);
                done = __wa_xfer_mark_seg_as_done(xfer, seg, WA_SEG_DONE);
        }
        spin_unlock_irqrestore(&xfer->lock, flags);
        if (done)
                wa_xfer_completion(xfer);
        if (rpipe_ready)
                wa_xfer_delayed_run(rpipe);
        return;

error_submit_buf_in:
        if (edc_inc(&wa->dti_edc, EDC_MAX_ERRORS, EDC_ERROR_TIMEFRAME)) {
                dev_err(dev, "DTI: URB max acceptable errors "
                        "exceeded, resetting device\n");
                wa_reset_all(wa);
        }
        if (printk_ratelimit())
                dev_err(dev, "xfer %p#%u: can't submit DTI data phase: %d\n",
                        xfer, seg_idx, result);
        seg->result = result;
        kfree(buf_in_urb->sg);
        buf_in_urb->sg = NULL;
error_buf_in_populate:
        __wa_xfer_abort(xfer);
        seg->status = WA_SEG_ERROR;
error_complete:
        xfer->segs_done++;
        rpipe_ready = rpipe_avail_inc(rpipe);
        wa_complete_remaining_xfer_segs(xfer, seg->index + 1, seg->status);
        done = __wa_xfer_is_done(xfer);
        /*
         * queue work item to clear STALL for control endpoints.
         * Otherwise, let endpoint_reset take care of it.
         */
        if (((usb_status & 0x3f) == WA_XFER_STATUS_HALTED) &&
                usb_endpoint_xfer_control(&xfer->ep->desc) &&
                done) {

                dev_info(dev, "Control EP stall.  Queue delayed work.\n");
                spin_lock(&wa->xfer_list_lock);
                /* move xfer from xfer_list to xfer_errored_list. */
                list_move_tail(&xfer->list_node, &wa->xfer_errored_list);
                spin_unlock(&wa->xfer_list_lock);
                spin_unlock_irqrestore(&xfer->lock, flags);
                queue_work(wusbd, &wa->xfer_error_work);
        } else {
                spin_unlock_irqrestore(&xfer->lock, flags);
                if (done)
                        wa_xfer_completion(xfer);
                if (rpipe_ready)
                        wa_xfer_delayed_run(rpipe);
        }

        return;

error_bad_seg:
        spin_unlock_irqrestore(&xfer->lock, flags);
        wa_urb_dequeue(wa, xfer->urb, -ENOENT);
        if (printk_ratelimit())
                dev_err(dev, "xfer %p#%u: bad segment\n", xfer, seg_idx);
        if (edc_inc(&wa->dti_edc, EDC_MAX_ERRORS, EDC_ERROR_TIMEFRAME)) {
                dev_err(dev, "DTI: URB max acceptable errors "
                        "exceeded, resetting device\n");
                wa_reset_all(wa);
        }
        return;

segment_aborted:
        /* nothing to do, as the aborter did the completion */
        spin_unlock_irqrestore(&xfer->lock, flags);
}

/*
 * Process a isochronous packet status message
 *
 * inbound transfers: need to schedule a buf_in_urb read
 */
static int wa_process_iso_packet_status(struct wahc *wa, struct urb *urb)
{
        struct device *dev = &wa->usb_iface->dev;
        struct wa_xfer_packet_status_hwaiso *packet_status;
        struct wa_xfer_packet_status_len_hwaiso *status_array;
        struct wa_xfer *xfer;
        unsigned long flags;
        struct wa_seg *seg;
        struct wa_rpipe *rpipe;
        unsigned done = 0, dti_busy = 0, data_frame_count = 0, seg_index;
        unsigned first_frame_index = 0, rpipe_ready = 0;
        size_t expected_size;

        /* We have a xfer result buffer; check it */
        dev_dbg(dev, "DTI: isoc packet status %d bytes at %p\n",
                urb->actual_length, urb->transfer_buffer);
        packet_status = (struct wa_xfer_packet_status_hwaiso *)(wa->dti_buf);
        if (packet_status->bPacketType != WA_XFER_ISO_PACKET_STATUS) {
                dev_err(dev, "DTI Error: isoc packet status--bad type 0x%02x\n",
                        packet_status->bPacketType);
                goto error_parse_buffer;
        }
        xfer = wa_xfer_get_by_id(wa, wa->dti_isoc_xfer_in_progress);
        if (xfer == NULL) {
                dev_err(dev, "DTI Error: isoc packet status--unknown xfer 0x%08x\n",
                        wa->dti_isoc_xfer_in_progress);
                goto error_parse_buffer;
        }
        spin_lock_irqsave(&xfer->lock, flags);
        if (unlikely(wa->dti_isoc_xfer_seg >= xfer->segs))
                goto error_bad_seg;
        seg = xfer->seg[wa->dti_isoc_xfer_seg];
        rpipe = xfer->ep->hcpriv;
        expected_size = struct_size(packet_status, PacketStatus,
                                    seg->isoc_frame_count);
        if (urb->actual_length != expected_size) {
                dev_err(dev, "DTI Error: isoc packet status--bad urb length (%d bytes vs %zu needed)\n",
                        urb->actual_length, expected_size);
                goto error_bad_seg;
        }
        if (le16_to_cpu(packet_status->wLength) != expected_size) {
                dev_err(dev, "DTI Error: isoc packet status--bad length %u\n",
                        le16_to_cpu(packet_status->wLength));
                goto error_bad_seg;
        }
        /* write isoc packet status and lengths back to the xfer urb. */
        status_array = packet_status->PacketStatus;
        xfer->urb->start_frame =
                wa->wusb->usb_hcd.driver->get_frame_number(&wa->wusb->usb_hcd);
        for (seg_index = 0; seg_index < seg->isoc_frame_count; ++seg_index) {
                struct usb_iso_packet_descriptor *iso_frame_desc =
                        xfer->urb->iso_frame_desc;
                const int xfer_frame_index =
                        seg->isoc_frame_offset + seg_index;

                iso_frame_desc[xfer_frame_index].status =
                        wa_xfer_status_to_errno(
                        le16_to_cpu(status_array[seg_index].PacketStatus));
                iso_frame_desc[xfer_frame_index].actual_length =
                        le16_to_cpu(status_array[seg_index].PacketLength);
                /* track the number of frames successfully transferred. */
                if (iso_frame_desc[xfer_frame_index].actual_length > 0) {
                        /* save the starting frame index for buf_in_urb. */
                        if (!data_frame_count)
                                first_frame_index = seg_index;
                        ++data_frame_count;
                }
        }

        if (xfer->is_inbound && data_frame_count) {
                int result, total_frames_read = 0, urb_index = 0;
                struct urb *buf_in_urb;

                /* IN data phase: read to buffer */
                seg->status = WA_SEG_DTI_PENDING;

                /* start with the first frame with data. */
                seg->isoc_frame_index = first_frame_index;
                /* submit up to WA_MAX_BUF_IN_URBS read URBs. */
                do {
                        int urb_frame_index, urb_frame_count;
                        struct usb_iso_packet_descriptor *iso_frame_desc;

                        buf_in_urb = &(wa->buf_in_urbs[urb_index]);
                        urb_frame_count = __wa_populate_buf_in_urb_isoc(wa,
                                buf_in_urb, xfer, seg);
                        /* advance frame index to start of next read URB. */
                        seg->isoc_frame_index += urb_frame_count;
                        total_frames_read += urb_frame_count;

                        ++(wa->active_buf_in_urbs);
                        result = usb_submit_urb(buf_in_urb, GFP_ATOMIC);

                        /* skip 0-byte frames. */
                        urb_frame_index =
                                seg->isoc_frame_offset + seg->isoc_frame_index;
                        iso_frame_desc =
                                &(xfer->urb->iso_frame_desc[urb_frame_index]);
                        while ((seg->isoc_frame_index <
                                                seg->isoc_frame_count) &&
                                 (iso_frame_desc->actual_length == 0)) {
                                ++(seg->isoc_frame_index);
                                ++iso_frame_desc;
                        }
                        ++urb_index;

                } while ((result == 0) && (urb_index < WA_MAX_BUF_IN_URBS)
                                && (seg->isoc_frame_index <
                                                seg->isoc_frame_count));

                if (result < 0) {
                        --(wa->active_buf_in_urbs);
                        dev_err(dev, "DTI Error: Could not submit buf in URB (%d)",
                                result);
                        wa_reset_all(wa);
                } else if (data_frame_count > total_frames_read)
                        /* If we need to read more frames, set DTI busy. */
                        dti_busy = 1;
        } else {
                /* OUT transfer or no more IN data, complete it -- */
                rpipe_ready = rpipe_avail_inc(rpipe);
                done = __wa_xfer_mark_seg_as_done(xfer, seg, WA_SEG_DONE);
        }
        spin_unlock_irqrestore(&xfer->lock, flags);
        if (dti_busy)
                wa->dti_state = WA_DTI_BUF_IN_DATA_PENDING;
        else
                wa->dti_state = WA_DTI_TRANSFER_RESULT_PENDING;
        if (done)
                wa_xfer_completion(xfer);
        if (rpipe_ready)
                wa_xfer_delayed_run(rpipe);
        wa_xfer_put(xfer);
        return dti_busy;

error_bad_seg:
        spin_unlock_irqrestore(&xfer->lock, flags);
        wa_xfer_put(xfer);
error_parse_buffer:
        return dti_busy;
}

/*
 * Callback for the IN data phase
 *
 * If successful transition state; otherwise, take a note of the
 * error, mark this segment done and try completion.
 *
 * Note we don't access until we are sure that the transfer hasn't
 * been cancelled (ECONNRESET, ENOENT), which could mean that
 * seg->xfer could be already gone.
 */
static void wa_buf_in_cb(struct urb *urb)
{
        struct wa_seg *seg = urb->context;
        struct wa_xfer *xfer = seg->xfer;
        struct wahc *wa;
        struct device *dev;
        struct wa_rpipe *rpipe;
        unsigned rpipe_ready = 0, isoc_data_frame_count = 0;
        unsigned long flags;
        int resubmit_dti = 0, active_buf_in_urbs;
        u8 done = 0;

        /* free the sg if it was used. */
        kfree(urb->sg);
        urb->sg = NULL;

        spin_lock_irqsave(&xfer->lock, flags);
        wa = xfer->wa;
        dev = &wa->usb_iface->dev;
        --(wa->active_buf_in_urbs);
        active_buf_in_urbs = wa->active_buf_in_urbs;
        rpipe = xfer->ep->hcpriv;

        if (usb_pipeisoc(xfer->urb->pipe)) {
                struct usb_iso_packet_descriptor *iso_frame_desc =
                        xfer->urb->iso_frame_desc;
                int     seg_index;

                /*
                 * Find the next isoc frame with data and count how many
                 * frames with data remain.
                 */
                seg_index = seg->isoc_frame_index;
                while (seg_index < seg->isoc_frame_count) {
                        const int urb_frame_index =
                                seg->isoc_frame_offset + seg_index;

                        if (iso_frame_desc[urb_frame_index].actual_length > 0) {
                                /* save the index of the next frame with data */
                                if (!isoc_data_frame_count)
                                        seg->isoc_frame_index = seg_index;
                                ++isoc_data_frame_count;
                        }
                        ++seg_index;
                }
        }
        spin_unlock_irqrestore(&xfer->lock, flags);

        switch (urb->status) {
        case 0:
                spin_lock_irqsave(&xfer->lock, flags);

                seg->result += urb->actual_length;
                if (isoc_data_frame_count > 0) {
                        int result, urb_frame_count;

                        /* submit a read URB for the next frame with data. */
                        urb_frame_count = __wa_populate_buf_in_urb_isoc(wa, urb,
                                 xfer, seg);
                        /* advance index to start of next read URB. */
                        seg->isoc_frame_index += urb_frame_count;
                        ++(wa->active_buf_in_urbs);
                        result = usb_submit_urb(urb, GFP_ATOMIC);
                        if (result < 0) {
                                --(wa->active_buf_in_urbs);
                                dev_err(dev, "DTI Error: Could not submit buf in URB (%d)",
                                        result);
                                wa_reset_all(wa);
                        }
                        /*
                         * If we are in this callback and
                         * isoc_data_frame_count > 0, it means that the dti_urb
                         * submission was delayed in wa_dti_cb.  Once
                         * we submit the last buf_in_urb, we can submit the
                         * delayed dti_urb.
                         */
                          resubmit_dti = (isoc_data_frame_count ==
                                                        urb_frame_count);
                } else if (active_buf_in_urbs == 0) {
                        dev_dbg(dev,
                                "xfer %p 0x%08X#%u: data in done (%zu bytes)\n",
                                xfer, wa_xfer_id(xfer), seg->index,
                                seg->result);
                        rpipe_ready = rpipe_avail_inc(rpipe);
                        done = __wa_xfer_mark_seg_as_done(xfer, seg,
                                        WA_SEG_DONE);
                }
                spin_unlock_irqrestore(&xfer->lock, flags);
                if (done)
                        wa_xfer_completion(xfer);
                if (rpipe_ready)
                        wa_xfer_delayed_run(rpipe);
                break;
        case -ECONNRESET:       /* URB unlinked; no need to do anything */
        case -ENOENT:           /* as it was done by the who unlinked us */
                break;
        default:                /* Other errors ... */
                /*
                 * Error on data buf read.  Only resubmit DTI if it hasn't
                 * already been done by previously hitting this error or by a
                 * successful completion of the previous buf_in_urb.
                 */
                resubmit_dti = wa->dti_state != WA_DTI_TRANSFER_RESULT_PENDING;
                spin_lock_irqsave(&xfer->lock, flags);
                if (printk_ratelimit())
                        dev_err(dev, "xfer %p 0x%08X#%u: data in error %d\n",
                                xfer, wa_xfer_id(xfer), seg->index,
                                urb->status);
                if (edc_inc(&wa->nep_edc, EDC_MAX_ERRORS,
                            EDC_ERROR_TIMEFRAME)){
                        dev_err(dev, "DTO: URB max acceptable errors "
                                "exceeded, resetting device\n");
                        wa_reset_all(wa);
                }
                seg->result = urb->status;
                rpipe_ready = rpipe_avail_inc(rpipe);
                if (active_buf_in_urbs == 0)
                        done = __wa_xfer_mark_seg_as_done(xfer, seg,
                                WA_SEG_ERROR);
                else
                        __wa_xfer_abort(xfer);
                spin_unlock_irqrestore(&xfer->lock, flags);
                if (done)
                        wa_xfer_completion(xfer);
                if (rpipe_ready)
                        wa_xfer_delayed_run(rpipe);
        }

        if (resubmit_dti) {
                int result;

                wa->dti_state = WA_DTI_TRANSFER_RESULT_PENDING;

                result = usb_submit_urb(wa->dti_urb, GFP_ATOMIC);
                if (result < 0) {
                        dev_err(dev, "DTI Error: Could not submit DTI URB (%d)\n",
                                result);
                        wa_reset_all(wa);
                }
        }
}

/*
 * Handle an incoming transfer result buffer
 *
 * Given a transfer result buffer, it completes the transfer (possibly
 * scheduling and buffer in read) and then resubmits the DTI URB for a
 * new transfer result read.
 *
 *
 * The xfer_result DTI URB state machine
 *
 * States: OFF | RXR (Read-Xfer-Result) | RBI (Read-Buffer-In)
 *
 * We start in OFF mode, the first xfer_result notification [through
 * wa_handle_notif_xfer()] moves us to RXR by posting the DTI-URB to
 * read.
 *
 * We receive a buffer -- if it is not a xfer_result, we complain and
 * repost the DTI-URB. If it is a xfer_result then do the xfer seg
 * request accounting. If it is an IN segment, we move to RBI and post
 * a BUF-IN-URB to the right buffer. The BUF-IN-URB callback will
 * repost the DTI-URB and move to RXR state. if there was no IN
 * segment, it will repost the DTI-URB.
 *
 * We go back to OFF when we detect a ENOENT or ESHUTDOWN (or too many
 * errors) in the URBs.
 */
static void wa_dti_cb(struct urb *urb)
{
        int result, dti_busy = 0;
        struct wahc *wa = urb->context;
        struct device *dev = &wa->usb_iface->dev;
        u32 xfer_id;
        u8 usb_status;

        BUG_ON(wa->dti_urb != urb);
        switch (wa->dti_urb->status) {
        case 0:
                if (wa->dti_state == WA_DTI_TRANSFER_RESULT_PENDING) {
                        struct wa_xfer_result *xfer_result;
                        struct wa_xfer *xfer;

                        /* We have a xfer result buffer; check it */
                        dev_dbg(dev, "DTI: xfer result %d bytes at %p\n",
                                urb->actual_length, urb->transfer_buffer);
                        if (urb->actual_length != sizeof(*xfer_result)) {
                                dev_err(dev, "DTI Error: xfer result--bad size xfer result (%d bytes vs %zu needed)\n",
                                        urb->actual_length,
                                        sizeof(*xfer_result));
                                break;
                        }
                        xfer_result = (struct wa_xfer_result *)(wa->dti_buf);
                        if (xfer_result->hdr.bLength != sizeof(*xfer_result)) {
                                dev_err(dev, "DTI Error: xfer result--bad header length %u\n",
                                        xfer_result->hdr.bLength);
                                break;
                        }
                        if (xfer_result->hdr.bNotifyType != WA_XFER_RESULT) {
                                dev_err(dev, "DTI Error: xfer result--bad header type 0x%02x\n",
                                        xfer_result->hdr.bNotifyType);
                                break;
                        }
                        xfer_id = le32_to_cpu(xfer_result->dwTransferID);
                        usb_status = xfer_result->bTransferStatus & 0x3f;
                        if (usb_status == WA_XFER_STATUS_NOT_FOUND) {
                                /* taken care of already */
                                dev_dbg(dev, "%s: xfer 0x%08X#%u not found.\n",
                                        __func__, xfer_id,
                                        xfer_result->bTransferSegment & 0x7f);
                                break;
                        }
                        xfer = wa_xfer_get_by_id(wa, xfer_id);
                        if (xfer == NULL) {
                                /* FIXME: transaction not found. */
                                dev_err(dev, "DTI Error: xfer result--unknown xfer 0x%08x (status 0x%02x)\n",
                                        xfer_id, usb_status);
                                break;
                        }
                        wa_xfer_result_chew(wa, xfer, xfer_result);
                        wa_xfer_put(xfer);
                } else if (wa->dti_state == WA_DTI_ISOC_PACKET_STATUS_PENDING) {
                        dti_busy = wa_process_iso_packet_status(wa, urb);
                } else {
                        dev_err(dev, "DTI Error: unexpected EP state = %d\n",
                                wa->dti_state);
                }
                break;
        case -ENOENT:           /* (we killed the URB)...so, no broadcast */
        case -ESHUTDOWN:        /* going away! */
                dev_dbg(dev, "DTI: going down! %d\n", urb->status);
                goto out;
        default:
                /* Unknown error */
                if (edc_inc(&wa->dti_edc, EDC_MAX_ERRORS,
                            EDC_ERROR_TIMEFRAME)) {
                        dev_err(dev, "DTI: URB max acceptable errors "
                                "exceeded, resetting device\n");
                        wa_reset_all(wa);
                        goto out;
                }
                if (printk_ratelimit())
                        dev_err(dev, "DTI: URB error %d\n", urb->status);
                break;
        }

        /* Resubmit the DTI URB if we are not busy processing isoc in frames. */
        if (!dti_busy) {
                result = usb_submit_urb(wa->dti_urb, GFP_ATOMIC);
                if (result < 0) {
                        dev_err(dev, "DTI Error: Could not submit DTI URB (%d)\n",
                                result);
                        wa_reset_all(wa);
                }
        }
out:
        return;
}

/*
 * Initialize the DTI URB for reading transfer result notifications and also
 * the buffer-in URB, for reading buffers. Then we just submit the DTI URB.
 */
int wa_dti_start(struct wahc *wa)
{
        const struct usb_endpoint_descriptor *dti_epd = wa->dti_epd;
        struct device *dev = &wa->usb_iface->dev;
        int result = -ENOMEM, index;

        if (wa->dti_urb != NULL)        /* DTI URB already started */
                goto out;

        wa->dti_urb = usb_alloc_urb(0, GFP_KERNEL);
        if (wa->dti_urb == NULL)
                goto error_dti_urb_alloc;
        usb_fill_bulk_urb(
                wa->dti_urb, wa->usb_dev,
                usb_rcvbulkpipe(wa->usb_dev, 0x80 | dti_epd->bEndpointAddress),
                wa->dti_buf, wa->dti_buf_size,
                wa_dti_cb, wa);

        /* init the buf in URBs */
        for (index = 0; index < WA_MAX_BUF_IN_URBS; ++index) {
                usb_fill_bulk_urb(
                        &(wa->buf_in_urbs[index]), wa->usb_dev,
                        usb_rcvbulkpipe(wa->usb_dev,
                                0x80 | dti_epd->bEndpointAddress),
                        NULL, 0, wa_buf_in_cb, wa);
        }
        result = usb_submit_urb(wa->dti_urb, GFP_KERNEL);
        if (result < 0) {
                dev_err(dev, "DTI Error: Could not submit DTI URB (%d) resetting\n",
                        result);
                goto error_dti_urb_submit;
        }
out:
        return 0;

error_dti_urb_submit:
        usb_put_urb(wa->dti_urb);
        wa->dti_urb = NULL;
error_dti_urb_alloc:
        return result;
}
EXPORT_SYMBOL_GPL(wa_dti_start);
/*
 * Transfer complete notification
 *
 * Called from the notif.c code. We get a notification on EP2 saying
 * that some endpoint has some transfer result data available. We are
 * about to read it.
 *
 * To speed up things, we always have a URB reading the DTI URB; we
 * don't really set it up and start it until the first xfer complete
 * notification arrives, which is what we do here.
 *
 * Follow up in wa_dti_cb(), as that's where the whole state
 * machine starts.
 *
 * @wa shall be referenced
 */
void wa_handle_notif_xfer(struct wahc *wa, struct wa_notif_hdr *notif_hdr)
{
        struct device *dev = &wa->usb_iface->dev;
        struct wa_notif_xfer *notif_xfer;
        const struct usb_endpoint_descriptor *dti_epd = wa->dti_epd;

        notif_xfer = container_of(notif_hdr, struct wa_notif_xfer, hdr);
        BUG_ON(notif_hdr->bNotifyType != WA_NOTIF_TRANSFER);

        if ((0x80 | notif_xfer->bEndpoint) != dti_epd->bEndpointAddress) {
                /* FIXME: hardcoded limitation, adapt */
                dev_err(dev, "BUG: DTI ep is %u, not %u (hack me)\n",
                        notif_xfer->bEndpoint, dti_epd->bEndpointAddress);
                goto error;
        }

        /* attempt to start the DTI ep processing. */
        if (wa_dti_start(wa) < 0)
                goto error;

        return;

error:
        wa_reset_all(wa);
}