arch/arm/boot/dts/omap5-cm-t54.dts

   1 // SPDX-License-Identifier: GPL-2.0
   2 /*
   3  * Support for CompuLab CM-T54
   4  */
   5 /dts-v1/;
   6
   7 #include "omap5.dtsi"
   8 #include <dt-bindings/interrupt-controller/irq.h>
   9 #include <dt-bindings/interrupt-controller/arm-gic.h>
  10
  11 / {
  12         model = "CompuLab CM-T54";
  13         compatible = "compulab,omap5-cm-t54", "ti,omap5";
  14
  15         memory@80000000 {
  16                 device_type = "memory";
  17                 reg = <0 0x80000000 0 0x7f000000>; /* 2048 MB */
  18         };
  19
  20         aliases {
  21                 display0 = &hdmi0;
  22                 display1 = &dvi0;
  23                 display2 = &lcd0;
  24         };
  25
  26         vmmcsd_fixed: fixed-regulator-mmcsd {
  27                 compatible = "regulator-fixed";
  28                 regulator-name = "vmmcsd_fixed";
  29                 regulator-min-microvolt = <3300000>;
  30                 regulator-max-microvolt = <3300000>;
  31         };
  32
  33         vwlan_pdn_fixed: fixed-regulator-vwlan-pdn {
  34                 compatible = "regulator-fixed";
  35                 regulator-name = "vwlan_pdn_fixed";
  36                 regulator-min-microvolt = <3300000>;
  37                 regulator-max-microvolt = <3300000>;
  38                 vin-supply = <&ldo2_reg>;
  39                 gpio = <&gpio4 13 GPIO_ACTIVE_HIGH>;   /* gpio4_109 */
  40                 startup-delay-us = <1000>;
  41                 enable-active-high;
  42         };
  43
  44         vwlan_fixed: fixed-regulator-vwlan {
  45                 compatible = "regulator-fixed";
  46                 regulator-name = "vwlan_fixed";
  47                 regulator-min-microvolt = <3300000>;
  48                 regulator-max-microvolt = <3300000>;
  49                 vin-supply = <&vwlan_pdn_fixed>;
  50                 gpio = <&gpio4 14 GPIO_ACTIVE_HIGH>;   /* gpio4_110 */
  51                 startup-delay-us = <1000>;
  52                 enable-active-high;
  53         };
  54
  55         ads7846reg: ads7846-reg {
  56                 compatible = "regulator-fixed";
  57                 regulator-name = "ads7846-reg";
  58                 regulator-min-microvolt = <3300000>;
  59                 regulator-max-microvolt = <3300000>;
  60         };
  61
  62         /* HS USB Host PHY on PORT 2 */
  63         hsusb2_phy: hsusb2_phy {
  64                 compatible = "usb-nop-xceiv";
  65                 reset-gpios = <&gpio3 12 GPIO_ACTIVE_LOW>; /* gpio3_76 HUB_RESET */
  66         };
  67
  68         /* HS USB Host PHY on PORT 3 */
  69         hsusb3_phy: hsusb3_phy {
  70                 compatible = "usb-nop-xceiv";
  71                 reset-gpios = <&gpio3 19 GPIO_ACTIVE_LOW>; /* gpio3_83 ETH_RESET */
  72         };
  73
  74         leds {
  75                 compatible = "gpio-leds";
  76                 led1 {
  77                         label = "Heartbeat";
  78                         gpios = <&gpio3 16 GPIO_ACTIVE_HIGH>; /* gpio3_80 ACT_LED */
  79                         linux,default-trigger = "heartbeat";
  80                         default-state = "off";
  81                 };
  82         };
  83
  84         lcd0: display {
  85                 compatible = "startek,startek-kd050c", "panel-dpi";
  86                 label = "lcd";
  87
  88                 pinctrl-names = "default";
  89                 pinctrl-0 = <&lcd_pins>;
  90
  91                 enable-gpios = <&gpio8 3 GPIO_ACTIVE_HIGH>;
  92
  93                 panel-timing {
  94                         clock-frequency = <33000000>;
  95                         hactive = <800>;
  96                         vactive = <480>;
  97                         hfront-porch = <40>;
  98                         hback-porch = <40>;
  99                         hsync-len = <43>;
 100                         vback-porch = <29>;
 101                         vfront-porch = <13>;
 102                         vsync-len = <3>;
 103                         hsync-active = <0>;
 104                         vsync-active = <0>;
 105                         de-active = <1>;
 106                         pixelclk-active = <1>;
 107                 };
 108
 109                 port {
 110                         lcd_in: endpoint {
 111                                 remote-endpoint = <&dpi_lcd_out>;
 112                         };
 113                 };
 114         };
 115
 116         hdmi0: connector0 {
 117                 compatible = "hdmi-connector";
 118                 label = "hdmi";
 119
 120                 type = "a";
 121
 122                 pinctrl-names = "default";
 123                 pinctrl-0 = <&hdmi_conn_pins>;
 124
 125                 hpd-gpios = <&gpio7 1 GPIO_ACTIVE_HIGH>; /* GPIO 193, HPD */
 126
 127                 port {
 128                         hdmi_connector_in: endpoint {
 129                                 remote-endpoint = <&hdmi_out>;
 130                         };
 131                 };
 132         };
 133
 134         tfp410: encoder0 {
 135                 compatible = "ti,tfp410";
 136
 137                 ports {
 138                         #address-cells = <1>;
 139                         #size-cells = <0>;
 140
 141                         port@0 {
 142                                 reg = <0>;
 143
 144                                 tfp410_in: endpoint {
 145                                         remote-endpoint = <&dpi_dvi_out>;
 146                                 };
 147                         };
 148
 149                         port@1 {
 150                                 reg = <1>;
 151
 152                                 tfp410_out: endpoint {
 153                                         remote-endpoint = <&dvi_connector_in>;
 154                                 };
 155                         };
 156                 };
 157         };
 158
 159         dvi0: connector1 {
 160                 compatible = "dvi-connector";
 161                 label = "dvi";
 162
 163                 digital;
 164
 165                 ddc-i2c-bus = <&i2c2>;
 166
 167                 port {
 168                         dvi_connector_in: endpoint {
 169                                 remote-endpoint = <&tfp410_out>;
 170                         };
 171                 };
 172         };
 173 };
 174
 175 &omap5_pmx_wkup {
 176
 177         ads7846_pins: pinmux_ads7846_pins {
 178                 pinctrl-single,pins = <
 179                         OMAP5_IOPAD(0x0042, PIN_INPUT_PULLDOWN | MUX_MODE6)  /* llib_wakereqin.gpio1_wk15 */
 180                 >;
 181         };
 182 };
 183
 184 &omap5_pmx_core {
 185         pinctrl-names = "default";
 186         pinctrl-0 = <
 187                         &led_gpio_pins
 188                         &usbhost_pins
 189         >;
 190
 191         led_gpio_pins: pinmux_led_gpio_pins {
 192                 pinctrl-single,pins = <
 193                         OMAP5_IOPAD(0x00b0, PIN_OUTPUT | MUX_MODE6) /* hsi2_caflag.gpio3_80 */
 194                 >;
 195         };
 196
 197         i2c1_pins: pinmux_i2c1_pins {
 198                 pinctrl-single,pins = <
 199                         OMAP5_IOPAD(0x01f2, PIN_INPUT_PULLUP | MUX_MODE0) /* i2c1_pmic_scl */
 200                         OMAP5_IOPAD(0x01f4, PIN_INPUT_PULLUP | MUX_MODE0) /* i2c1_pmic_sda */
 201                 >;
 202         };
 203
 204         i2c2_pins: pinmux_i2c2_pins {
 205                 pinctrl-single,pins = <
 206                         OMAP5_IOPAD(0x01b8, PIN_INPUT | MUX_MODE0) /* i2c2_scl */
 207                         OMAP5_IOPAD(0x01ba, PIN_INPUT | MUX_MODE0) /* i2c2_sda */
 208                 >;
 209         };
 210
 211         mmc1_pins: pinmux_mmc1_pins {
 212                 pinctrl-single,pins = <
 213                         OMAP5_IOPAD(0x01e2, PIN_INPUT_PULLUP | MUX_MODE0) /* sdcard_clk */
 214                         OMAP5_IOPAD(0x01e4, PIN_INPUT_PULLUP | MUX_MODE0) /* sdcard_cmd */
 215                         OMAP5_IOPAD(0x01e6, PIN_INPUT_PULLUP | MUX_MODE0) /* sdcard_data2 */
 216                         OMAP5_IOPAD(0x01e8, PIN_INPUT_PULLUP | MUX_MODE0) /* sdcard_data3 */
 217                         OMAP5_IOPAD(0x01ea, PIN_INPUT_PULLUP | MUX_MODE0) /* sdcard_data0 */
 218                         OMAP5_IOPAD(0x01ec, PIN_INPUT_PULLUP | MUX_MODE0) /* sdcard_data1 */
 219                 >;
 220         };
 221
 222         mmc2_pins: pinmux_mmc2_pins {
 223                 pinctrl-single,pins = <
 224                         OMAP5_IOPAD(0x0040, PIN_INPUT_PULLUP | MUX_MODE0) /* emmc_clk */
 225                         OMAP5_IOPAD(0x0042, PIN_INPUT_PULLUP | MUX_MODE0) /* emmc_cmd */
 226                         OMAP5_IOPAD(0x0044, PIN_INPUT_PULLUP | MUX_MODE0) /* emmc_data0 */
 227                         OMAP5_IOPAD(0x0046, PIN_INPUT_PULLUP | MUX_MODE0) /* emmc_data1 */
 228                         OMAP5_IOPAD(0x0048, PIN_INPUT_PULLUP | MUX_MODE0) /* emmc_data2 */
 229                         OMAP5_IOPAD(0x004a, PIN_INPUT_PULLUP | MUX_MODE0) /* emmc_data3 */
 230                         OMAP5_IOPAD(0x004c, PIN_INPUT_PULLUP | MUX_MODE0) /* emmc_data4 */
 231                         OMAP5_IOPAD(0x004e, PIN_INPUT_PULLUP | MUX_MODE0) /* emmc_data5 */
 232                         OMAP5_IOPAD(0x0050, PIN_INPUT_PULLUP | MUX_MODE0) /* emmc_data6 */
 233                         OMAP5_IOPAD(0x0052, PIN_INPUT_PULLUP | MUX_MODE0) /* emmc_data7 */
 234                 >;
 235         };
 236
 237         mmc3_pins: pinmux_mmc3_pins {
 238                 pinctrl-single,pins = <
 239                         OMAP5_IOPAD(0x01a4, PIN_INPUT_PULLUP | MUX_MODE0) /* wlsdio_clk */
 240                         OMAP5_IOPAD(0x01a6, PIN_INPUT_PULLUP | MUX_MODE0) /* wlsdio_cmd */
 241                         OMAP5_IOPAD(0x01a8, PIN_INPUT_PULLUP | MUX_MODE0) /* wlsdio_data0 */
 242                         OMAP5_IOPAD(0x01aa, PIN_INPUT_PULLUP | MUX_MODE0) /* wlsdio_data1 */
 243                         OMAP5_IOPAD(0x01ac, PIN_INPUT_PULLUP | MUX_MODE0) /* wlsdio_data2 */
 244                         OMAP5_IOPAD(0x01ae, PIN_INPUT_PULLUP | MUX_MODE0) /* wlsdio_data3 */
 245                 >;
 246         };
 247
 248         wlan_gpios_pins: pinmux_wlan_gpios_pins {
 249                 pinctrl-single,pins = <
 250                         OMAP5_IOPAD(0x019c, PIN_OUTPUT_PULLDOWN | MUX_MODE6) /* abemcpdm_ul_data.gpio4_109 */
 251                         OMAP5_IOPAD(0x019e, PIN_OUTPUT_PULLDOWN | MUX_MODE6) /* abemcpdm_dl_data.gpio4_110 */
 252                 >;
 253         };
 254
 255         usbhost_pins: pinmux_usbhost_pins {
 256                 pinctrl-single,pins = <
 257                         OMAP5_IOPAD(0x00c4, PIN_INPUT | MUX_MODE0)  /* usbb2_hsic_strobe */
 258                         OMAP5_IOPAD(0x00c6, PIN_INPUT | MUX_MODE0)  /* usbb2_hsic_data */
 259
 260                         OMAP5_IOPAD(0x01dc, PIN_INPUT | MUX_MODE0)  /* usbb3_hsic_strobe */
 261                         OMAP5_IOPAD(0x01de, PIN_INPUT | MUX_MODE0)  /* usbb3_hsic_data */
 262
 263                         OMAP5_IOPAD(0x00a8, PIN_OUTPUT | MUX_MODE6) /* hsi2_caready.gpio3_76 */
 264                         OMAP5_IOPAD(0x00b6, PIN_OUTPUT | MUX_MODE6) /* hsi2_acdata.gpio3_83 */
 265                 >;
 266         };
 267
 268         dss_hdmi_pins: pinmux_dss_hdmi_pins {
 269                 pinctrl-single,pins = <
 270                         OMAP5_IOPAD(0x013c, PIN_INPUT | MUX_MODE0) /* hdmi_cec */
 271                         OMAP5_IOPAD(0x0140, PIN_INPUT | MUX_MODE0) /* hdmi_ddc_scl */
 272                         OMAP5_IOPAD(0x0142, PIN_INPUT | MUX_MODE0) /* hdmi_ddc_sda */
 273                 >;
 274         };
 275
 276         lcd_pins: pinmux_lcd_pins {
 277                 pinctrl-single,pins = <
 278                         OMAP5_IOPAD(0x0172, PIN_OUTPUT_PULLDOWN | MUX_MODE6) /* timer11_pwm_evt.gpio8_227 */
 279                 >;
 280         };
 281
 282         hdmi_conn_pins: pinmux_hdmi_conn_pins {
 283                 pinctrl-single,pins = <
 284                         OMAP5_IOPAD(0x013e, PIN_INPUT | MUX_MODE6) /* hdmi_hpd.gpio7_193 */
 285                 >;
 286         };
 287
 288         dss_dpi_pins: pinmux_dss_dpi_pins {
 289                 pinctrl-single,pins = <
 290                         OMAP5_IOPAD(0x0104, PIN_OUTPUT | MUX_MODE3) /* rfbi_data15.dispc_data15 */
 291                         OMAP5_IOPAD(0x0106, PIN_OUTPUT | MUX_MODE3) /* rfbi_data14.dispc_data14 */
 292                         OMAP5_IOPAD(0x0108, PIN_OUTPUT | MUX_MODE3) /* rfbi_data13.dispc_data13 */
 293                         OMAP5_IOPAD(0x010a, PIN_OUTPUT | MUX_MODE3) /* rfbi_data12.dispc_data12 */
 294                         OMAP5_IOPAD(0x010c, PIN_OUTPUT | MUX_MODE3) /* rfbi_data11.dispc_data11 */
 295                         OMAP5_IOPAD(0x010e, PIN_OUTPUT | MUX_MODE3) /* rfbi_data10.dispc_data10 */
 296                         OMAP5_IOPAD(0x0110, PIN_OUTPUT | MUX_MODE3) /* rfbi_data9.dispc_data9 */
 297                         OMAP5_IOPAD(0x0112, PIN_OUTPUT | MUX_MODE3) /* rfbi_data8.dispc_data8 */
 298                         OMAP5_IOPAD(0x0114, PIN_OUTPUT | MUX_MODE3) /* rfbi_data7.dispc_data7 */
 299                         OMAP5_IOPAD(0x0116, PIN_OUTPUT | MUX_MODE3) /* rfbi_data6.dispc_data6 */
 300                         OMAP5_IOPAD(0x0118, PIN_OUTPUT | MUX_MODE3) /* rfbi_data5.dispc_data5 */
 301                         OMAP5_IOPAD(0x011a, PIN_OUTPUT | MUX_MODE3) /* rfbi_data4.dispc_data4 */
 302                         OMAP5_IOPAD(0x011c, PIN_OUTPUT | MUX_MODE3) /* rfbi_data3.dispc_data3 */
 303                         OMAP5_IOPAD(0x011e, PIN_OUTPUT | MUX_MODE3) /* rfbi_data2.dispc_data2 */
 304                         OMAP5_IOPAD(0x0120, PIN_OUTPUT | MUX_MODE3) /* rfbi_data1.dispc_data1 */
 305                         OMAP5_IOPAD(0x0122, PIN_OUTPUT | MUX_MODE3) /* rfbi_data0.dispc_data0 */
 306                         OMAP5_IOPAD(0x0124, PIN_OUTPUT | MUX_MODE3) /* rfbi_we.dispc_vsync */
 307                         OMAP5_IOPAD(0x0126, PIN_OUTPUT | MUX_MODE3) /* rfbi_cs0.dispc_hsync */
 308                         OMAP5_IOPAD(0x0128, PIN_OUTPUT | MUX_MODE3) /* rfbi_a0.dispc_de */
 309                         OMAP5_IOPAD(0x012a, PIN_OUTPUT | MUX_MODE3) /* rfbi_re.dispc_pclk */
 310                         OMAP5_IOPAD(0x012c, PIN_OUTPUT | MUX_MODE3) /* rfbi_hsync0.dispc_data17 */
 311                         OMAP5_IOPAD(0x012e, PIN_OUTPUT | MUX_MODE3) /* rfbi_te_vsync0.dispc_data16 */
 312                         OMAP5_IOPAD(0x0130, PIN_OUTPUT | MUX_MODE3) /* gpio6_182.dispc_data18 */
 313                         OMAP5_IOPAD(0x0132, PIN_OUTPUT | MUX_MODE3) /* gpio6_183.dispc_data19 */
 314                         OMAP5_IOPAD(0x0134, PIN_OUTPUT | MUX_MODE3) /* gpio6_184.dispc_data20 */
 315                         OMAP5_IOPAD(0x0136, PIN_OUTPUT | MUX_MODE3) /* gpio6_185.dispc_data21 */
 316                         OMAP5_IOPAD(0x0138, PIN_OUTPUT | MUX_MODE3) /* gpio6_186.dispc_data22 */
 317                         OMAP5_IOPAD(0x013a, PIN_OUTPUT | MUX_MODE3) /* gpio6_187.dispc_data23 */
 318                 >;
 319         };
 320
 321         mcspi2_pins: pinmux_mcspi1_pins {
 322                 pinctrl-single,pins = <
 323                         OMAP5_IOPAD(0x00fc, PIN_INPUT | MUX_MODE0) /* mcspi2_clk */
 324                         OMAP5_IOPAD(0x00fe, PIN_INPUT | MUX_MODE0) /* mcspi2_simo */
 325                         OMAP5_IOPAD(0x0100, PIN_INPUT | MUX_MODE0) /* mcspi2_somi */
 326                         OMAP5_IOPAD(0x0102, PIN_INPUT | MUX_MODE0) /* mcspi2_cs0 */
 327                 >;
 328         };
 329 };
 330
 331 &mcspi2 {
 332         pinctrl-names = "default";
 333         pinctrl-0 = <&mcspi2_pins>;
 334
 335         /* touch controller */
 336         ads7846@0 {
 337                 pinctrl-names = "default";
 338                 pinctrl-0 = <&ads7846_pins>;
 339
 340                 compatible = "ti,ads7846";
 341                 vcc-supply = <&ads7846reg>;
 342
 343                 reg = <0>;                              /* CS0 */
 344                 spi-max-frequency = <1500000>;
 345
 346                 interrupt-parent = <&gpio1>;
 347                 interrupts = <15 0>;                    /* gpio1_wk15 */
 348                 pendown-gpio = <&gpio1 15 GPIO_ACTIVE_HIGH>;
 349
 350
 351                 ti,x-min = /bits/ 16 <0x0>;
 352                 ti,x-max = /bits/ 16 <0x0fff>;
 353                 ti,y-min = /bits/ 16 <0x0>;
 354                 ti,y-max = /bits/ 16 <0x0fff>;
 355
 356                 ti,x-plate-ohms = /bits/ 16 <180>;
 357                 ti,pressure-max = /bits/ 16 <255>;
 358
 359                 ti,debounce-max = /bits/ 16 <30>;
 360                 ti,debounce-tol = /bits/ 16 <10>;
 361                 ti,debounce-rep = /bits/ 16 <1>;
 362
 363                 wakeup-source;
 364         };
 365 };
 366
 367 &mmc1 {
 368         pinctrl-names = "default";
 369         pinctrl-0 = <&mmc1_pins>;
 370         vmmc-supply = <&ldo9_reg>;
 371         bus-width = <4>;
 372 };
 373
 374 &mmc2 {
 375         pinctrl-names = "default";
 376         pinctrl-0 = <&mmc2_pins>;
 377         vmmc-supply = <&vmmcsd_fixed>;
 378         bus-width = <8>;
 379         ti,non-removable;
 380 };
 381
 382 &mmc3 {
 383         pinctrl-names = "default";
 384         pinctrl-0 = <
 385                 &mmc3_pins
 386                 &wlan_gpios_pins
 387         >;
 388         vmmc-supply = <&vwlan_fixed>;
 389         bus-width = <4>;
 390         ti,non-removable;
 391 };
 392
 393 &mmc4 {
 394         status = "disabled";
 395 };
 396
 397 &mmc5 {
 398         status = "disabled";
 399 };
 400
 401 &i2c1 {
 402         pinctrl-names = "default";
 403         pinctrl-0 = <&i2c1_pins>;
 404
 405         clock-frequency = <400000>;
 406
 407         at24@50 {
 408                 compatible = "atmel,24c02";
 409                 pagesize = <16>;
 410                 reg = <0x50>;
 411         };
 412
 413         palmas: palmas@48 {
 414                 compatible = "ti,palmas";
 415                 interrupts = <GIC_SPI 7 IRQ_TYPE_NONE>; /* IRQ_SYS_1N */
 416                 reg = <0x48>;
 417                 interrupt-controller;
 418                 #interrupt-cells = <2>;
 419                 ti,system-power-controller;
 420
 421                 extcon_usb3: palmas_usb {
 422                         compatible = "ti,palmas-usb-vid";
 423                         ti,enable-vbus-detection;
 424                         ti,enable-id-detection;
 425                         ti,wakeup;
 426                 };
 427
 428                 rtc {
 429                         compatible = "ti,palmas-rtc";
 430                         interrupt-parent = <&palmas>;
 431                         interrupts = <8 IRQ_TYPE_NONE>;
 432                 };
 433
 434                 palmas_pmic {
 435                         compatible = "ti,palmas-pmic";
 436                         interrupt-parent = <&palmas>;
 437                         interrupts = <14 IRQ_TYPE_NONE>;
 438                         interrupt-names = "short-irq";
 439
 440                         ti,ldo6-vibrator;
 441
 442                         regulators {
 443                                 smps123_reg: smps123 {
 444                                         /* VDD_OPP_MPU */
 445                                         regulator-name = "smps123";
 446                                         regulator-min-microvolt = < 600000>;
 447                                         regulator-max-microvolt = <1500000>;
 448                                         regulator-always-on;
 449                                         regulator-boot-on;
 450                                 };
 451
 452                                 smps45_reg: smps45 {
 453                                         /* VDD_OPP_MM */
 454                                         regulator-name = "smps45";
 455                                         regulator-min-microvolt = < 600000>;
 456                                         regulator-max-microvolt = <1310000>;
 457                                         regulator-always-on;
 458                                         regulator-boot-on;
 459                                 };
 460
 461                                 smps6_reg: smps6 {
 462                                         /* VDD_DDR3 - over VDD_SMPS6 */
 463                                         regulator-name = "smps6";
 464                                         regulator-min-microvolt = <1500000>;
 465                                         regulator-max-microvolt = <1500000>;
 466                                         regulator-always-on;
 467                                         regulator-boot-on;
 468                                 };
 469
 470                                 smps7_reg: smps7 {
 471                                         /* VDDS_1v8_OMAP over VDDS_1v8_MAIN */
 472                                         regulator-name = "smps7";
 473                                         regulator-min-microvolt = <1800000>;
 474                                         regulator-max-microvolt = <1800000>;
 475                                         regulator-always-on;
 476                                         regulator-boot-on;
 477                                 };
 478
 479                                 smps8_reg: smps8 {
 480                                         /* VDD_OPP_CORE */
 481                                         regulator-name = "smps8";
 482                                         regulator-min-microvolt = < 600000>;
 483                                         regulator-max-microvolt = <1310000>;
 484                                         regulator-always-on;
 485                                         regulator-boot-on;
 486                                 };
 487
 488                                 smps9_reg: smps9 {
 489                                         /* VDDA_2v1_AUD over VDD_2v1 */
 490                                         regulator-name = "smps9";
 491                                         regulator-min-microvolt = <3300000>;
 492                                         regulator-max-microvolt = <3300000>;
 493                                         ti,smps-range = <0x80>;
 494                                         regulator-always-on;
 495                                         regulator-boot-on;
 496                                 };
 497
 498                                 smps10_out2_reg: smps10_out2 {
 499                                         /* VBUS_5V_OTG */
 500                                         regulator-name = "smps10_out2";
 501                                         regulator-min-microvolt = <5000000>;
 502                                         regulator-max-microvolt = <5000000>;
 503                                         regulator-always-on;
 504                                         regulator-boot-on;
 505                                 };
 506
 507                                 smps10_out1_reg: smps10_out1 {
 508                                         /* VBUS_5V_OTG */
 509                                         regulator-name = "smps10_out1";
 510                                         regulator-min-microvolt = <5000000>;
 511                                         regulator-max-microvolt = <5000000>;
 512                                 };
 513
 514                                 ldo1_reg: ldo1 {
 515                                         /* VDDAPHY_CAM: vdda_csiport */
 516                                         regulator-name = "ldo1";
 517                                         regulator-min-microvolt = <1800000>;
 518                                         regulator-max-microvolt = <1800000>;
 519                                 };
 520
 521                                 ldo2_reg: ldo2 {
 522                                         /* VDD_3V3_WLAN */
 523                                         regulator-name = "ldo2";
 524                                         regulator-min-microvolt = <3300000>;
 525                                         regulator-max-microvolt = <3300000>;
 526                                         startup-delay-us = <1000>;
 527                                 };
 528
 529                                 ldo3_reg: ldo3 {
 530                                         /* VCC_1V5_AUD */
 531                                         regulator-name = "ldo3";
 532                                         regulator-min-microvolt = <1500000>;
 533                                         regulator-max-microvolt = <1500000>;
 534                                         regulator-always-on;
 535                                         regulator-boot-on;
 536                                 };
 537
 538                                 ldo4_reg: ldo4 {
 539                                         /* VDDAPHY_DISP: vdda_dsiport/hdmi */
 540                                         regulator-name = "ldo4";
 541                                         regulator-min-microvolt = <1800000>;
 542                                         regulator-max-microvolt = <1800000>;
 543                                 };
 544
 545                                 ldo5_reg: ldo5 {
 546                                         /* VDDA_1V8_PHY: usb/sata/hdmi.. */
 547                                         regulator-name = "ldo5";
 548                                         regulator-min-microvolt = <1800000>;
 549                                         regulator-max-microvolt = <1800000>;
 550                                         regulator-always-on;
 551                                         regulator-boot-on;
 552                                 };
 553
 554                                 ldo6_reg: ldo6 {
 555                                         /* VDDS_1V2_WKUP: hsic/ldo_emu_wkup */
 556                                         regulator-name = "ldo6";
 557                                         regulator-min-microvolt = <1200000>;
 558                                         regulator-max-microvolt = <1200000>;
 559                                         regulator-always-on;
 560                                         regulator-boot-on;
 561                                 };
 562
 563                                 ldo7_reg: ldo7 {
 564                                         /* VDD_VPP: vpp1 */
 565                                         regulator-name = "ldo7";
 566                                         regulator-min-microvolt = <2000000>;
 567                                         regulator-max-microvolt = <2000000>;
 568                                         /* Only for efuse reprograming! */
 569                                         status = "disabled";
 570                                 };
 571
 572                                 ldo8_reg: ldo8 {
 573                                         /* VDD_3V_GP: act led/serial console */
 574                                         regulator-name = "ldo8";
 575                                         regulator-min-microvolt = <3000000>;
 576                                         regulator-max-microvolt = <3000000>;
 577                                         regulator-always-on;
 578                                         regulator-boot-on;
 579                                 };
 580
 581                                 ldo9_reg: ldo9 {
 582                                         /* VCC_DV_SDIO: vdds_sdcard */
 583                                         regulator-name = "ldo9";
 584                                         regulator-min-microvolt = <1800000>;
 585                                         regulator-max-microvolt = <3000000>;
 586                                         regulator-boot-on;
 587                                 };
 588
 589                                 ldoln_reg: ldoln {
 590                                         /* VDDA_1v8_REF: vdds_osc/mm_l4per.. */
 591                                         regulator-name = "ldoln";
 592                                         regulator-min-microvolt = <1800000>;
 593                                         regulator-max-microvolt = <1800000>;
 594                                         regulator-always-on;
 595                                         regulator-boot-on;
 596                                 };
 597
 598                                 ldousb_reg: ldousb {
 599                                         /* VDDA_3V_USB: VDDA_USBHS33 */
 600                                         regulator-name = "ldousb";
 601                                         regulator-min-microvolt = <3250000>;
 602                                         regulator-max-microvolt = <3250000>;
 603                                         regulator-always-on;
 604                                         regulator-boot-on;
 605                                 };
 606
 607                                 regen3_reg: regen3 {
 608                                         /* REGEN3 controls LDO9 supply to card */
 609                                         regulator-name = "regen3";
 610                                         regulator-always-on;
 611                                         regulator-boot-on;
 612                                 };
 613                         };
 614                 };
 615         };
 616 };
 617
 618 &i2c2 {
 619         pinctrl-names = "default";
 620         pinctrl-0 = <&i2c2_pins>;
 621
 622         clock-frequency = <100000>;
 623 };
 624
 625 &usbhshost {
 626         port2-mode = "ehci-hsic";
 627         port3-mode = "ehci-hsic";
 628 };
 629
 630 &usbhsehci {
 631         phys = <0 &hsusb2_phy &hsusb3_phy>;
 632 };
 633
 634 &usb3 {
 635        extcon = <&extcon_usb3>;
 636        vbus-supply = <&smps10_out1_reg>;
 637 };
 638
 639 &cpu0 {
 640         cpu0-supply = <&smps123_reg>;
 641 };
 642
 643 &dss {
 644         status = "ok";
 645
 646         pinctrl-names = "default";
 647         pinctrl-0 = <&dss_dpi_pins>;
 648
 649         port {
 650                 #address-cells = <1>;
 651                 #size-cells = <0>;
 652
 653                 dpi_dvi_out: endpoint@0 {
 654                         reg = <0>;
 655                         remote-endpoint = <&tfp410_in>;
 656                         data-lines = <24>;
 657                 };
 658
 659                 dpi_lcd_out: endpoint@1 {
 660                         reg = <1>;
 661                         remote-endpoint = <&lcd_in>;
 662                         data-lines = <24>;
 663                 };
 664         };
 665 };
 666
 667 &dsi2 {
 668         status = "ok";
 669         vdd-supply = <&ldo4_reg>;
 670 };
 671
 672 &hdmi {
 673         status = "ok";
 674         vdda-supply = <&ldo4_reg>;
 675
 676         pinctrl-names = "default";
 677         pinctrl-0 = <&dss_hdmi_pins>;
 678
 679         port {
 680                 hdmi_out: endpoint {
 681                         remote-endpoint = <&hdmi_connector_in>;
 682                         lanes = <1 0 3 2 5 4 7 6>;
 683                 };
 684         };
 685 };